CWEK-21/2024-25 PROVN OF COVERED REPAIR BAY AT 588 FRI GULMARG UNDER GE 969 EWS

Amount

M & L Brick work with sub class 'B' bricks (old size bricks) straight on curved on plan exc 6 M mean radius built in CM 1:4 complete all as specified and directed by Engr-in-Charge.

M & L Brick work with sub class ‘B’ bricks, straight or curved on plan any radius in half brick thick wall with old size bricks built in cement mortar 1:4 complete all as specified and directed by Engr-in-Charge.

M & L Rendering 15 mm thick in cement and sand mortar 1:4 on fair faces of brick work or cement concrete surfaces with using integral waterproofing compound 3% by weight of cement including finishing the surface even and smooth without using extra cement complete all as specified and directed by Engr-in-Charge. (Note - WPC shall be measured and paid separately).

M & L Rendering 10 mm thick in cement and sand mortar 1:6 on other than fair faces of brick work or cement concrete surfaces including finishing the surface even and smooth without using extra cement complete all as specified and directed by Engr-in-Charge.

M & L Rendering 5 mm thick in cement and sand mortar 1:3 on fair faces of brick work or cement concrete surfaces including finishing the surface even and smooth without using extra cement on ceilingcomplete all as specified and directed by Engr-in-Charge.

Supply only integral water proofing compound complete all as specified and directed by Engr-in-Charge..

M&L for Preparation of newly plastered surfaces of walls and applying two coats of oil bound distemper over a coat of chalk whiting, preparatory to distempering complete all as specified and directed by Engr-in-Charge.

M&L for Preparation of newly plastered surfaces of walls and applying two coats of cement base paint over a coat of primer complete all as specified and directed by Engr-in-Charge.

M&L for Preparation of newly plastered surfaces of walls and applying three coats of white wash complete all as specified and directed by Engr-in-Charge.

M&L Preparation of newly plastered surfaces of walls and applying two coats of dry distemper over a coat of clearcolle on plastered surfaces, preparatory to distempering on walls complete all as specified and directed by Engr-in-Charge.

M&L for Preparation of newly plastered surfaces of ceilings and applying three coats of white wash complete all as specified and directed by Engr-in-Charge.

M&L for cement concrete type E-2, 1:5:10, in foundation, filling and mass concrete in flooring complete all as specified and directed by Engr-in-Charge.

M&L 75mm thick PCC 1:2:4, type B-2, (20mm graded aggregate) as in sub base complete all as specified and directed by Engr-in-Charge.

M&L 75mm thick PCC 1:2:4, type B-2, (20mm graded aggregate) as in sub base/floor finishing the surface of concrete topping even and fair, without using extr cement complete all as specified and directed by Engr-in-Charge.

M&L for 15mm thick wearproof topping as specified (incorporating an approved metallic floor hardner), laid on concrete floors and paving and finished even and smooth (except metallic hardner) complete all as specified and directed by Engr-in-Charge.

Supplied only metallic hardner complete all as specified and directed by Engr-in-Charge.

M&L for 25mm thick PCC 1:2:4 type B-O (using 12.5 graded aggregate) as in sub base complete all as specified and directed by Engr-in-Charge.

M&L for 10mm thick screed bed or bedding layer in cement mortar 1:4 for laying floor finishes complete all as specified and directed by Engr-in-Charge.

M&L vitrified tiles 10mm thick dark shade (square/ rectangular) polished , area of each tiles n.exc 0.36 Sqm in floors, set and jointed pointed in white or coloured cement to match complete all as specified and directed by Engr-in-Charge.

M&L non skid ceramic tiles 7 to 8mm thick coloured tiles (square/rectangular) area of each tiles exc 0.06 Sqm but n.exc 0.11 Sqm in floors set and jointed pointed in white or coloured cement to match complete all as specified and directed by Engr-in-Charge.

M&L for rendering 10mm thick in CM 1:3 on vertical surfaces complete all as specified and directed by Engr-in-Charge.

M&L glazed coloured ceramic coloured tiles in vertical surface 450x350x7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed by Engr-in-Charge.

M & L for hardcore of gauge not exceeding 63 mm of broken stone, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface complete all as specified and directed by Engr-in-Charge.

M&L 75mm thick PCC 1:3:6, type C-2, (40mm graded aggregate) as in plinth protection and similar works including finisheing the surface of concrete topping even and fair, without using extr cement complete all as specified and directed by Engr-in-Charge.

M & L for formwork to sides and soffits of suspended slabs such as roof slabs, floor slas, landing and similar work n.exc 200mm thick, etc flat and fair finished surface of concrete,complete all as specified and directed by Engr-in-Charge.

M & L for formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintes, etc flat and fair finished surface of concrete.complete all as specified and directed by Engr-in-Charge.

M & L for formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete, railings, opening in concrete walls, floors and roofs n.exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but n.exc 20cm wide complete and fair finished surface of concrete, complete all as specified and directed by Engr-in-Charge.

M&L for RCC (nominal mix) type B-1, 1:2:4 (20mm graded aggregate) in beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed by Engr-in-Charge.

M&L for RCC (nominal mix) type B-1, 1:2:4 (20mm graded aggregate) in slaabs supported on walls, beams and columns in floors, roofs, landings, shelves and the like complete all as specified and directed by Engr-in-Charge.

S & F Mild steel TMT bars 10 mm dia and over, quality conforming to Grade 415 MPA cut to length , bent to shape required including cranking , bending and binding with mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed by Engr-in-Charge.

All as per item No-30 above but 5mm dia and above including 10mm dia in stirrups complete all as specified and directed by Engr-in-Charge.

S & F Roof trusses, trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. (unframed work) complete all as specified and directed by Engr-in-Charge.

S&F mild steel screw bolts hexagonal or square heads at one end and screwed the other, or screwed end to be fitted with washers and one hexaganal or suare nut exc 22.5cm and n.exc 300mm long and diameter of neck 16 to 20mm complete all as specified and directed by Engr-in-Charge.

S&F MS works in hand rails, half round or other steel section or core for wooden hand rail, straight portion, drilled and countersunk for balusters running bars for doors, balusters, nosing to steps, including embeding in concrete and screwing etc wind ties for roof including securing bolts etc confirming to Fe-290 Gde E-165 complete all as specified and directed by Engr-in-Charge.

M&L for Preparation of new or previously untreated steel surfaces of any description, over 10cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed by Engr-in-Charge.

M&L for Preparation of new or previously untreated steel surfaces of any description, n.exc 10cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primercomplete all as specified and directed by Engr-in-Charge.

S&F 0.63mm thick, galvanised, corrugated mild steel sheeting with two corrugation side lap, fixed with coach screws and washers, in roofs, walls etc with grade of zinc coating 275 grams per square metre complete all as specified and directed by Engr-in-Charge.

S&F 0.80mm thick plain, galvanised, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashing (length and girth as fixed) with grade of zinc coating 275 grams per square metre complete all as specified and directed by Engr-in-Charge.

M&L for preparing new zinc (or galvanized) surfaces to receive painting by coating with mordant solution including washing and cleaning etc. of any description, over 10cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and directed by Engr-in-Charge.

S&F Steel rolling shutters with out ball bearing as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer erected in position as indicated complete But gear operated type with bevel gear box and crank handle and thickness of laths 1.25mm complete all as specified and directed by Engr-in-Charge.

S&F 2nd Class Soft wood plain, solid straight chowkats and frmaes, wrought, framed rebated on the solid rounded or chamfered put together with glue pinned at joint complete all as specified and directed by Engr-in-Charge.

S&F 2nd class hard wood 35mm thick factory made panelled shutters with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and stype as per IS-1003 (Pt-I) kiln seasoned and chemically pressure treated complete all as specified and directed by Engr-in-Charge.

S & F Solid PVC Door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube, complete all as shown in drawing of relevant item in MES, schedule Part-II , 2010 complete all as specified and directed by Engr-in-Charge.

S & F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail. Panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement complete all as shown in drawing of relevant item complete all as specified and directed by Engr-in-Charge.

M&L for MS Cold rolled butt hinges medium weight 100mm long complete all as specified and directed by Engr-in-Charge.

S&F 300mm long aluminium alloy, anodised, sliding door bolt with hasp (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolkts and sliding bolts of extruded section or cast aluminium aloy and fixed it complete all as specified and directed by Engr-in-Charge.

S&F aluminium anodised barrel tower bolts, 150mm long complete all as specified and directed by Engr-in-Charge.

S&F extruded aluminium alloy handles, fabricated type 150 mm long complete all as specified and directed by Engr-in-Charge.

S&F steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed by Engr-in-Charge.

S&F steel ventilators with top hung shutter including hinges steel peg stay, squares no.exc 0.50 Sqm in each pane complete all as specified and directed by Engr-in-Charge.

S & F 4mm thick sheet glass, ordinary quality and glazing with oil putty in square n.exc 0.50 Sqm in each pane complete all as specified and directed by Engr-in-Charge.

S & F 4 mm thick figured glass pin head ftype and glazing with oil putty in squares n.exc 0.5 sqm in each pane complete all as specified and directed by Engr-in-Charge.

S & F Vitreous China squatting pan “Orissa pattern” size 580x440mm white with integral foot rest (excluding flushing cistern and flush pipe) with CI ‘P’ trap of long arm of suitable size including connection to flush pipe, anti symphonic pipes etc , complete all as specified and directed by Engr-in-Charge.

S & F PVC low level flushing cistern, valveless, syphonic action type, 10 litres capacity with inlet, ball valve float and handle with and including brackets & PVC bend pipe 90 cm long etc, supplied and fixed, complete all as specified and directed by Engr-in-Charge.

S&F vitreous China wash basin, white, flat back size 550x400 mm including pillar tape, waste fitting chromium plated brass and rubber plug, procelain stopper, a pair of CI brackets, waste pipe and pillar tape etc. complete all as specified and directed by Engr-in-Charge.

S&F pillar tap, CP fancy type of 15 mm with capstan heads, screwed down, high pressure, with or without lattered 'Hot or Cold' with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and directed by Engr-in-Charge.

S&F urinal, full vitreous China , white and full etc. complete all as specified and directed by Engr-in-Charge.

S&F urinal spreaders of PTMT ay colour for fixing with 15mm dia pipe ( minimum wt 60 gms) complete all as specified and directed by Engr-in-Charge.

S&F 75 mm bore PVC (SWR) Bends with accesss door etc complete all as specified and directed by Engr-in-Charge.

S&F for PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls for 75 mm bore pipe Etc complete all as specified and directed by Engr-in-Charge.

S&F for PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls for 110 mm bore pipe Etc complete all as specified and directed by Engr-in-Charge.

S&F for PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floors for 75 mm bore pipe complete all as specified and directed by Engr-in-Charge.

S&F for PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floors for 110 mm bore pipe complete all as specified and directed by Engr-in-Charge.

S&F for PVC (SWR) bend with access door inluding jointing with solvent cement 75 mm bore complete all as specified and directed by Engr-in-Charge.

S&F for PVC (SWR) bend with access door inluding jointing with solvent cement 110 mm bore complete all as specified and directed by Engr-in-Charge.

M&L for 125/110 mm PVC (SWR) Gully Trap setting and jointed with solvent cement complete all as specified and directed by Engr-in-Charge.

M&L for 75 mm PVC (SWR) floor trap setting and jointed with solvent cement complete all as specified and directed by Engr-in-Charge.

M&L for 75 mm PVC (SWR) vent cowl setting and jointed with solvent cement complete all as specified and directed by Engr-in-Charge.

S&F MS works bends, straps, supports or stays for rainwater, ventilating pipes including securing with nut, bolts etc similar small articles confirming to FE-290 Gde E-165 complete all as specified and directed by Engr-in-Charge.

S&F 15mm bore medium graded GI tubing with all fittings and fixed complete to wall and ceiling or laid in trenches complete all as specified and directed by Engr-in-Charge.

S&F 20mm bore medium graded GI tubing with all fittings and fixed complete to wall and ceiling or laid in trenches complete all as specified.

S&F 20mm bore ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed (min weight 20mm-210 gms) complete all as specified and directed by Engr-in-Charge.

S & F PVC connection 15 mm size, of length 450 mm, with PTMT nuts supplied and fixedcomplete all as specified and directed by Engr-in-Charge.

S&F 15mm bore angle valve, fancy type chromium plated high pressure with crutch or butterfly handle screwed both ends for iron pipe complete all as specified and directed by Engr-in-Charge.

S&F 15mm bore dia Bib taps fancy type, cast copper alloy with crutch or butterfly handle, screwed down, serewed for iron pipe or for brass ferrule and fixed complete all as specified and directed by Engr-in-Charge.

S&F 1000 Ltrs capacity Rotational moulded polyethylene in white coloured three layered ISI marked water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified and directed by Engr-in-Charge.

M & L Painting to new wood or wood based surfaces of any description not otherwise described over 10 cm in width or girth including preparation of surfaces, priming with pink primer (one coat) finished with two coats of synthetic enamel paint complete all as specified and directed by Engr-in-Charge.

S&F 2nd class soft wood 20mm thick in facia boarding fixed with nails in any situation planed one side with butt joints complete all as specified and directed by Engr-in-Charge.

S&F 20mm thick Granite (of any type) machine cut in partition, liad on with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishingcomplete all as specified and directed by Engr-in-Charge.

Excavation in trenches in any type of soil, n exc 1.5 M wide and n exc 1.5 M deep for foundation, etc or for shafts, wells, manholes etc foundation of pole laying of cable etc, n.exc 10 Sqm on plan and n.exc 1.5m in depth and getting out hard dense soil complete all as specified and directed by Engr-in-Charge.

Returning filling in incl spreading leveling, watering and well ramming in layers n exc 25 cm complete all as specified and directed by Engr-in-Charge.

Removing of excavated soil not exceeding 50m and depositing where directed at a level not exc 1.5 M above the starting pointcomplete all as specified and directed by Engr-in-Charge.

S&F second class softwood plain fillets square, rectangular or triangular in section, wrought secured with screws, cross sectional area exc 13 and n.exc 25 Sqcm complete all as specified and directed by Engr-in-Charge.

M&L for 6mm thick veneered decorative plywood, grade 1 (with BWR resin) with decorative face veneers on one face has decorative veneer fixed with nails to timber frame work in ceiling etc complete all as specified and directed by Engr-in-Charge.

M&L Cement concrete 1:4:8 type D-2 (using 40 mm graded crushed stone aggregate) as in foundation filling and mass complete all as specified and directed by Engr-in-Charge.

M&L Walling of Random rubble masonary, uncoused, well bonded, bedded and solidly hearted, built in cement mortar 1:4 complete all as specified and directed by Engr-in-Charge.

Extra over stone walling for hammer dressing with maximum depression on face from straight edge held against the dressed surface n.exc 40mm to face stones and dressing of face beds and joints,as specified,of random rubble walling,uncoursed or brought upto courses for Granite or Trap Stone complete all as specified and directed by Engr-in-Charge.

M&L Flush pointing in cement mortar 1:4 to random rubble masonry ,uncoursed or brought upto courses all as specified and directed.

M&L for Boulder filling dry hand packed tightly as in back of wall complete all as specified and directed by Engr-in-Charge.

S & F 110 mm bore of pipe PVC (SWR) pipes single socket in any length as in weep holes etc complete all as specified and directed by Engr-in-Charge.

M&L plain cement concrete (1:2:4), type B-0 (using 12.5mm graded crushed stone aggregate) as in benching, bed plates, copings and the like including necessary formwork complete all as specified and directed by Engr-in-Charge.

M&L pre cast cement concrete (1:2:4), type B-1 (using 20mm graded crushed stone aggregate) set in cement mortar 1:6 in bond stons for stone masonry and the like including necessary formwork. complete all as specified and directed by Engr-in-Charge.

Rolling and consolidatiion formation in cutting with roller using 8 to 12 Ton power roller complete to required level, gradient, slope, camber, super elevation including filling depression and including approved earth which may occure during rolling process complete all as specified and directed by Engr-in-Charge.

Surface excavation not exceeding 30cm deep and averaging 15cm deep and getting out in hard/dense soil for roads to required slop gradient, camber etc complete all as specified and directed by Engr-in-Charge.

M&L for soling (or sub base) 150mm thick compacted thickness with broken boulders or quarried stone, interstices filled, surface formed and rolled and consolidated ti reqyured gradient and camber with 8 to 12 tonne power roller complete all as specified and directed by Engr-in-Charge.

M&L 150mm thick cement concrete 1:4:8, D-2 using 40mm graded aggregate in sub base floor, paving and hard standing complete all as specified and directed by Engr-in-Charge.

M&L cement concrete work in pavement of flexural strength 40 Kg per square centimetre in field using 400 Kg of cement per cum thickness of concrete 25cm or less complete all as specified and directed by Engr-in-Charge.

Formwork to edges of concrete flats, threads, threads, bricks in floors, opening in concrete walls, floor and roofs n.exc 200mm wide and sides of RCC/PCC bend in walls, horizonattal or sloping and similar work exc 10cm but n.exc 20cm wide complete all as specified and directed by Engr-in-Charge.

M&L forming 12mm thick expansion joints for 150mm thick concrete, filled with pre-formed bituminious filler and top 30mm primed and sealed with sealing compound, Grade `A',complete all as specified and directed by Engr-in-Charge.

M&L forming conctraction (dummy) joints 65mm deep x 10m wide, filled with sealing compound `A' Grade complete all as specified and directed by Engr-in-Charge.

Forming construction joint 150mm deep x 10mm wide filled with sealing compound, complete all as specified and directed by Engr-in-Charge.

M&L for PCC 1:3:6, Type C-2 (40mm graded aggregate) as in fdns, filling and mass concrete etc complete all as specified and directed by Engr-in-Charge.

M&L plain cement concrete 1:2:4, type B-1 (using 20mm graded crushed stone aggregate) as in benching, bed plates, copings and the like including necessary formwork, complete all as specified and directed by Engr-in-Charge.

Extra over stone walling for hammer dressing with maximum depression on face from straight edge held against the dressed surface nexc 40mm to face stones and dressing of face beds and joints,as specified,of random rubble walling,uncoursed or brought upto coursese for lime or sand stone complete all as specified and directed by Engr-in-Charge.

M&L for cement concrete type B1, 1:2:4 (20mm graded aggregate) as in surface channel and drains complete all as specified and directed by Engr-in-Charge.

Extra for forming fair faces (finished) drain of channel 30 cm inner girth in cement concrete using extra cement including forms moulds mitered stopped end etc complete all as specified and directed by Engr-in-Charge.

LLDPE Septic tank exc inordinary soil foundation in PCC 1:2:4 brick work in CM 1:4 RCC slab covers including RCC precast manhole cover having 6 mm plate embedded all arround/fiber reiforced cover with angle iron frame vent shaft and sludge chamber etc complete for 10 users complete all as specified as per manufactures instructions and directed by Enginner-in-Charge.

Soakage well exc in ordinary soil foundation in PCC 1:3:6 well of honey combed and solid in M-25 concrete including intercepting chamber screen chamber brick work in CM 1:4, RCC cover slab in M-25/RR Masonary/filling with brick bats, complete of size 2.40M dia x 3.00m deep complete all as specified and directed by Engr-in-Charge. and shown in drg No CESZ/TD-1078/2011.

M & L Brickwork with sub class ‘B’ (old size) bricks, straight or curved on plan exceeding 6 metre mean radius built in cement sand mortar 1:6 complete all as specified and directed by Engr-in-Charge.

M&L for 150 mm dia Reinforced concrete pipes, class NP2, laid and jointed complete with collars, complete all as specified and directed by Engr-in-Charge.

M&L for concrete bed to drain pipes in PCC 1:3:6 type C-2 using 40mm graded crushed stone aggregate including packing under haunching again, the sides of pipe after they are laid and tested for 150mm dia, complete all as specified and directed by Engr-in-Charge.

M&L for for rendering 15mm thick in CM 1:4 on fair faces of brick work or concrete surfaces and finished surfaces even and smooth complete all as specified and directed by Engr-in-Charge.

M & L precast RCC man holes cover in cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate, complete all as specified and directed by Engr-in-Charge.

Material and labour for point wiring with 1.5 Sqmm copper conductor FRLS (Stranded) PVC insulated ISI Marked unsheathed cable in and including concealed PVC conduits, medium grade, ISI marked not less than 20 mm dia with all fittings/ accessories and also including PVC insulated ISI marked unsheathed 1.5 Sqmm copper multistranded conductor FRLS as earth wire connected to common earth dolly and including sunk cast iron/pressed mild steel terminal boxes, junction boxes, other boxes made from 2 mm thick mild steel sheet of suitable sizes for mounting of switches, sockets, fan regulators, light fittings etc. covered with 3mm thick plastic laminated sheet (Make Hylum or equivalent ISI marked) for One light point/fan point controlled by one way switch 5 Amps complete all as specified and directed by Engr-in-Charge.

Description all as item no.115 above but for One 3 pin socket outlet 5 Amps on independent board, complete all as specified and directed by Engr-in-Charge.

Material and labour for point wiring with 2.5 Sqmm copper conductor FRLS (Stranded) PVC insulated ISI Marked unsheathed cable in and including concealed PVC conduits, medium grade, ISI marked not less than 20 mm dia with all fittings/ accessories and also including PVC insulated ISI marked unsheathed 1.5 Sqmm copper multistranded conductor FRLS as earth wire connected to common earth dolly and including sunk cast iron/pressed mild steel terminal boxes, junction boxes, other boxes made from 2 mm thick mild steel sheet of suitable sizes for mounting of 15A switches & sockets. covered with 3mm thick plastic laminated sheet (Make Hylum or equivalent ISI marked) for One 15A Socket point controlled by one way switch 15 Amps complete all as specified and directed by Engr-in-Charge.

S & F fixed Switch piano flush type single pole, one way 5/6 Amp, complete all as specified and directed by Engr-in-Charge. .

S & F Socket outlet 2 in 1, 3 Pin, 5 Amp, 230 Volts complete all as specified and directed by Engr-in-Charge.

Supply & Fixing Switch socket combination 6A/16A, 5 in 1 flush type with neon fuse and indictor complete all as specified and directed by Engr-in-Charge. (Anchor- Cat No.39593) Make : Anchor or Equivalent

S&F Ceiling rose surface bakelite surface 65x50 mm 3 trminals fixed on wall/ceiling and including PVC block, complete all as specified and directed by Engr-in-Charge.

Supply & Fixing Lamp holder, insulated body, threaded dome pattern, suitable for bracket fittings,complete all as specified and directed by Engr-in-Charge.

Supply and fixing LED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed by Engr-in-Charge.

Supply and fixing Energy saving, environment friendly & robust IP65 protected LED 50 watt midbay with PDC housing suitable for ceiling (Surface/Suspended) mount & available in Wide beam optics complete all as specified and directed by Engr-in-Charge. Make :- Havells cat part No. ILIOSBAYPLUSHBP50WLED857SP90DTOPC or eqiuvalent

Supply & Fixing in repair exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250m. complete all as specified and directed by Engr-in-Charge. Make : Havells or Equivalent

Supply & Fixing MCB DB Triple pole and neutral 4 way sheet metal enclosure 415 volts, 50 Hz, with IP-42 protection,Double door with 200 Amps standard bus bar of suitable size and common neutral link all enclosed in standard sheet flush mounting complete all as specified and directed by Engr-in-Charge.

Supply & Fixing MCB DB 12 way sheet metal enclosure SPN 240 volts, 50 Hz, with IP-42 protection,single door with 200 Amps standard bus bar of suitable size and common neutral link all enclosed in standard sheet flush mounting complete all as specified and directed by Engr-in-Charge.

Supply & Fixing 240V, 10 KA 'B' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 6 to 32 AMP, in the MCB DB Complete with connection testing and commissioning,complete all as specified and directed by Engr-in-Charge.

Supply & Fixing in repair amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of two poles and current carrying capacity 63 Amp SPN in the MCB DB complete with connection testing and commissioning ,complete all as specified and directed by Engr-in-Charge.

Supply and fixing 415V 10KA 'C' curve miniature circuit breaker (MCB) of TPN and current carrying capacity 100 Amp in the DB complete with connection testing and commissioning all as specified and directed by Engr-in-Charge.

Supply and fixing 415V 10KA 'C' curve miniature circuit breaker (MCB) of TPN and current carrying capacity 16 to 32 Amp in the DB complete with connection testing and commissioning complete all as specified and directed by Engr-in-Charge.

S & F 16 A 3P+N+E insulated plug & socket for 3 phase power supply complete all as specified and directed by Engineer-in-charge. Make :-Havells Cat part No. DHDPBTN016 or Equivalent

S & F in repair Sub main wiring using two runs of single core PVC insulated cable with copper conductor multistranded 1100 volts of sizes 6.0 Sqmm through new non metalic PVC casing capping including copper earth wire in green colour of size 6.0 Sqmm connection to DB with thimbling complete all as specified and directed by Engr-in-Charge. (Note:- Two runs of sub main wire including earth wire and rigid non metalic PVC casing capping shall be measured as one unit per RM make of cable.

S & F in repair Sub main wiring using four runs of single core PVC insulated cable with copper conductor multistranded 1100 volts of sizes 6.0 Sqmm through new non metalic PVC casing capping including copper earth wire in green colour of size 6.0 Sqmm connection to DB with thimbling complete as specified and directed. (Note:- four runs of sub main wire including earth wire and rigid non metalic PVC casing capping shall be measured as one unit per RM make of cable complete all as specified and directed by Engr-in-Charge.

Supply,installation,testing and commissioning outdoor type,plinth mounted step down transformer,11KV/433 volts (at no load) AC 3 phase 50HZ, 63 KVA capacity,core type,double copper wound,oil immersed,naturally cooled,oil natural Air Natural(ON AN) with external cooling tubes,delta connected on primary side(HV) and star connected on secondary side (LV) in accordance with vector group DYN-11(vector group) with neutral brought out on secondary side (LV side) and having taping at 0 (plus/ minus)2.5%, (plus/minus)5%,&(Plus/minus)7.5% on HV side to be charged by means of hands operated off load tap changer gear. switch handle shall be provided with the locking arrangement along with top position indicator.The transformer shall be IS:1180(Part-I) 2014 with maximum total losses as per energy efficiency level 2 of IS:1180 (Part I)2014 and shall comprise of the following:

a) HT cable box on primary side including all accessories as required. b) One cable box on LV side(Secondary Side) Consisting of four Nos porcelain bushing with copper rods. Complete with nuts and washers with two Nos of cable glands suitable for reception taking out of XLPE insulated heavy duty armoured cables including glands,Joints and jointing materials complete. c) Oil conservator with filter type drain valve and oil level gauge. d) De-hydrating breather with first fill dehydrating agent (Silica Gel) (e) Explosive vent. (f) Thermometer pocket on tank cover g) One No 100mm dia,dial type thermometer,Vapour pressure type,having range 0-120°C with metal guard having maximum perimeter reading temperature indicator with resisting device for transformer. h) Two Nos earth terminals for body earthing and two Nos earthing terminals for neutral earthing. (j) Rating plate and terminal marking plate (k) Oil level gauge (l) Oil drain filter valve (m) Lifting Lugs

Construction of transformer shed for transformer of capacity upto 300 KVA complete all as specified and show on Drg No CESZ/TD-1110/2011 Sheet 1/1 and 2/2 dated 01.12.11

Supply Installation testing and Commissioning of servo voltage stabilizer fully automatic micro processor based control card of capacity 25 KVA three phase ,Oil Cooled,Indoor type and designed for input variation between 200 volts to 480 V output voltage stabilized at 415V with accuracy of +- 1% and speed of Voltage correction should not be less than 8V/Sec,Input frequency 47 to 53 Hz having Facility to auto and manual operation,No load loss should be less than 0.5% operating temp -20°C to 45°C above ambient and suitable to operate with unbalanced load including initial oil filling upto appropriate level with new Easter oil and having all standard accessories complete all as specified and directed with and including following additional features:- High and low voltage cut off system, Single phase prevention and reverse phase protection system,Overload and short circuit protection by provided MCCB of suitable Amps and KA rating 4pole having adjustable thermal and adjustable magnetic setting,Incoming control by providing MCCB of 315Amps and 36KA rating 4Pole with adjustable thermal magnettic setting.complete all as specified and directed by Engr In Charge.

Supply and fix cable jointing kit for 11 KV Earthed grade cable for out door termination Heat shrink type joint complete with jointing material and accessories suitable for 3 core XLPE, armoured, Al conductor cable of size 95Sqmm complete as specified and directed by Engr In Charge

Supply and fix steel tubular swaged poles complete with cast iron plate finial taper plug,bolt,nuts & screws as specified type 410 SP-55 11Mtr with 300MM x 300MM x 6mm cast iron plate finial tapper plug,bolts,nuts and screws and making holes as per requirement all as specified including factory painted with two coats of black bituminious paint internally throughout and externally for embedded portion and applying one coat of red oxide primer making 5Nos of strips each 30CM high with super enamel paint black and yellow/white from ground level coping upto 1.5Mtr painting with two coats of aluminium paint for remaining height complete all as specified and directed by Engineer-in-Charge.

Material & Labour for switch air break gang operated outdoor HT 11KV triple pole mechanically operated mounted on HT insulators (12 insulators) type MS galvanised steel frame with operating mechanism worked from ground level including operating rod of GI pipe of 25mm bore with handle for current rating 200Amps 11000volts complete with locking arrangements MS clamps,bolts,nuts,and washers etc. including fuse barrels of required capacity to suite the load at site including two coats of aluminium paint over a coat of red oxide primer on MS work complete all as specified and directed by Engr In Charge.

Supply and fix HT lightning arrestor for outdoor use,non linear resistor type,complete with all fittings capacity 10KA suitable for 11 KV grade complete all as specified and directed by Engr In Charge.

Supply, laying & testing cable XLPE insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty)with stranded aluminium conductor, 11000 volts grade, of size 3 core 95 sq mm laid in trenches/on walls/Air/Pole in duct through pipe.complete all as specified and directed by Engr In Charge.

Supply and lay cable XLPE insulated screened PVC beded galvanised steel strip or wire armoured electric power cables (heavy duty) 1100 volts grade with standard aluminium conductor of size 95 sq mm 3.5 core laid in trenches fixed along with poles or passed through GI Pipe using clamps whereever reqd complete all as specified and directed by Engr In Charge.

Supply and lay cable XLPE insulated screened PVC beded galvanised steel strip or wire armoured electric power cables (heavy duty) 1100 volts grade with standard aluminium conductor of size 70 sq mm 3.5 core laid in trenches fixed along with poles or passed through GI Pipe using clamps whereever reqd complete all as specified and directed by Engr In Charge.

Supply and lay cable XLPE insulated screened PVC beded galvanised steel strip or wire armoured electric power cables (heavy duty) 1100 volts grade with standard aluminium conductor of size 35 sq mm 3.5 core complete all as specified and directed by Engr In Charge.

Supply, install, testing and commissioning of LT feeder piller box outdoor type made out of 3.15 mm thick CRCA sheet and MS angle iron frame with weather proof canopy, mounted on PCC pedestal, cubical type, front and rear side openable, compartment type with hinged door ligting lugs 2 Nos, earthing strips at rear side, bottom detachable gland plate complete with suitable size zinc and passivated nut, bolts spring and washers and locking arrangement for each compartment, provision of air vent, dust and vermin proof, provision of cable alley with 400 amps rated aluminium bus bar having 1100 volts grade sleaving and internal connection should be provided with aluminium strips of suitable size and to accommodate and including the following MCCBS duly painted with 2 coats powder coating over a coat of anticorrosive red oxide primer should accomodate the following accessories. complete all as specified and directed by Engr In Charge.

Material & Labour for fine and dry sand cushioning for underground cable by providing a layers of sand 8CM deep before laying and and 15 CM deep after laying the cable including trenching the cable,complete all as specified and as directed. Note: Punned thickness of sand layer shall be measured and paid to contractor.Punned layer thickness to be paid as per SSR part I Complete all as specified and directed by Engineer-in-Charge.

Material & Labour for sub class brick laid dry width wise across the cable in trenches for protection of cable Complete all as specified and directed by Engineer-in-Charge.

Supply and Laying reinforced precast PCC Cable Cover ISI Marked,Class EHV,Type-I with peak size 450MM x 230MM x 50MM for covering cables laid dry flat as cable protection on Sand Complete all as specified and directed by Engineer-in-Charge.

Earthing complete with galvanised steel earth plate electrode 60×60cm.× 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less'than 1.5 metres below normal ground level, earth plate surrounded by 15 CM thick packed layer of charcoal and common salt alternatively upto 90CM and connected with and including GI strip of size 32x6 mm by means of bolts,nuts,checknuts,and washers 40mm bore GI pipe light grade from earth plate upto testing point for protection of strip and 20mm bore GI pipe medium grade with wire mesh and funnel for watering including necessary excavation and earthwork PCC chamber (1:3:6) type C2 with RCC cover complete all as shown in electrical plate no 3 of MES schedule Part I of SSR Part I(2009) Complete all as specified and directed by Engineer-in-Charge. Notes:(i) RCC pit cover shall be pre cast of RCC(1:2:4) type B 40mm thick reinforcement with 8mm TOR steel @ 100 C/C in leiu of CI cover and the rate includes in the unit rate of item (ii) Earth electrode shall be protected upto test point using necessary arrangement with suitable size GI pipe and the rate includes in the unit rate of item. (iii) Earth pit chamber and RCC cover shall be painted with red paint over a primer coat and the rate includes in the unit rate.

Supply and fixing LED street light fitting 90 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete complete all as specified and directed by engineer -in-charge. Note : The contractor shall be produced the two yrs warranty card during supply Complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing GI pipe bracket ,made out of GI pipe 40 mm dia light grade 1.2mtr long bend to the shape 120 degrees angle including clamps-02 set made out of MS flat (50x6mm) duly bend to shape for PCC/steel tubular pole , nuts,bolts and washers etc, complete all as directed at site.

M&L plain cement concrete 1:2:4 type C1 (using 20mm graded crushed stone aggregate as in copying of pole complete all as specified and directed by Engr in charge.

M&L for Cross arms, bracings, supports, clamps and back plates fabricated from structural steel sections including nuts, bolts, washers, welding, bending cold or hot, drilling holes for bolts, in any shape or size as indicated or directed and inclusive of one primer coat, one under coat and one finishing coat of paint complete all as specified and directed by an Engr In Charge.

Material and Labour for Cutting of existing GI pipe line of size upto 50 mm dia and inseting new pipe line of dia 40mm including all fittings complete all as specified and directed by Engr In Charge.

S & F GI tubing medium grade with screwed socket joints together with all fittings(such as bend,elbows,tees,short pieces,connectors,back nuts,diminishing pieces cap plug and unions etc and fixing complete with clips,wall hooks,wooden plug of size 25 MM dia complete all as specified and directed by Engr In Charge.

S & F GI tubing medium grade with screwed socket joints together with all fittings(such as bend,elbows,tees,short pieces,connectors,back nuts,diminishing pieces cap plug and unions etc and fixing complete with clips,wall hooks,wooden plug of size 40 MM dia complete all as specified and directed by Engr In Charge.

S & F of Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe or unions and fixed suitable of 25 mm dia sizes complete all as specified and directed by Engr In Charge.

S & F of Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe or unions and fixed suitable of 40mm dia sizes complete all as specified and directed by Engr In Charge.

M&L for construction of brick valve pit of size (0.6Mx0.6Mx0.6M) internal dimensions including all excavation and earth work in any type of soil and disposal of soil to a distance of not existing 50 mtr and depositing all as directed including 10 mm plastering internally in cement mortar 1:4, 100mm thick at with angle iron frame (40x40x6mm) including handle, locking arrangement will be provided including two coats of synthetic enamel paint over a coat of red oxide primer on sheet surface complete all as directed by Engr-in-Charge.

M/S MIR & CO

M/S Manzoor and Co