SPECIAL REPAIR TO BLDG NO ET-67 AND OTHER SANCTIONED WORKS AT RANGIA MILITARY STATION UNDER GE RANGIA

Amount

Taking down cement plaster on brick or stone walls, etc., including raking out joints, hacking for key, scrubbing down with water, etc., complete all as specified and as directed by Engineer-in-charge.

Taking down chowkat or frame exceeding 1.5 Sqm but not exceeding 4 Sqm each (without taking off shutter from the frame), complete all as specified and as directed by Engineer-in-charge.

Taking down chowkat or frame not exceeding 1.5 Sqm each (without taking off shutter from the frame), complete all as specified and as directed by Engineer-in-charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as per specified and as directed by Engineer-in-charge.

Demolition of unreinforced cement concrete in ground floors and pavings nexc 15 cm thickness (below or above ground level) complete all as specified and as directed by Engineer-in-charge.

Demolition of reinforced cement concrete in ground floors and pavings nexc 15 cm thickness (below or above ground level) complete all as specified and as directed by Engineer-in-charge.

Dismantling boarding, any description fixed in any position with nails, complete all as specified and as directed by Engineer-in-charge.

Taking up or down 15 mm bore steel tubing and connections, complete all as per specified and as directed by Engineer-in-charge.

Taking up or down 20 mm bore steel tubing and connections, complete all as per specified and as directed by Engineer-in-charge.

S&F GI tube 15 mm bore medium grade with fittings and fixed complete to wall, ceiling or laid in floor complete all as specified and as directed by Engineer-in-charge.

S&F GI tube 20 mm bore medium grade with fittings and fixed complete to wall, ceiling or laid in floor complete all as specified and as directed by Engineer-in-charge.

Dismantling Asbestos Cement (Corrugated, Semi corrugated etc.) sheets in roof coverings, complete all as specified and as directed by Engineer-in-charge.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm single side prelam PVC sheet used instead of plain colour PVC sheet & edges will be painted to match with prelam sheet, reinforced with M.S Square tube complete all as per specified and as directed by Engineer-in-charge.

S&F Solid PVC Door Frame of size 50mm x 95mm made out of 5mm single side prelam PVC sheet used instead of plain colour PVC sheet & edges will be painted to match with prelam sheet, reinforced with M.S Square tube complete all as per specified and as directed by Engineer-in-charge.

Supply and fixing Factory Made Solid PVC Moulded Door Shutter (with woof free EPS), 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing complete all as per specified and as directed by Engineer-in-charge.

S&F Factory made solid wire gauzed pvc door shutter 30mm thick (style) consisting of frame made out of M.S.tubes for top & bottom rails.M.S.frame shall be covered with heat moulded prelam PVC "C" channel having a prelam PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and prelam PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panells will be wire gaused in lieu of single side prelam PVC sheet panel. The wire gause shall be wrapped on an additional square 8 mm MS solid tube and this tube shall be welded to MS tubes. The wire gause shall be stretched to tighten firmly. And jointed to gether with solvent cement, suppling & fixing in the frame at site complete all as per specified and as directed by Engineer-in-charge.

Supply and fixing factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. .frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail,; Paneling of plain colour PVC sheet to be fitted in the M.S. frame welded/ sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement complete all as per specified and as directed by Engineer-in-charge.

S&F solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet rainforced with MS square tube in opening complete all as per specified and as directed by Engineer-in-charge.

Demolition of brick work built in any cement mortar complete all as specified and as directed by Engineer-in-charge.

M&L for brick work with sub-class `B' old size bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar (1:4) complete all as specified and as directed by Engineer-in-charge.

M&L for 15 mm thick rendering on fair faces of brick work or one side of lathing in cement mortar (1:4), mixing with water proofing compound @ 2% by weight of cement consumed and surface finished even and smooth without using extra cement complete all as specified and as directed by Engineer-in-charge. Note: WPC shall be measured and paid separately.

M&L for 10 mm thick rendering on fair faces of brick work or concrete block in cement mortar (1:6) and surface finished even and smooth without using extra cement complete all as specified and as directed by Engineer-in-charge.

M&L for preparing new plastered surfaces and applying two coats of oil bound distemper on walls over 1 mm thick wall care putty on plastered surface, complete all as per specified and as directed by Engineer-in-charge.

M&L for preparing old plastered surfaces and applying two coats of oil bound distemper on walls over 1 mm thick wall care on plastered surface including complete removal of existing treatment complete all as per specified and as directed by Engineer-in-charge.

M&L for preparing new plastered surfaces and applying two coats of cement base paint on walls, complete all as per specified and as directed by Engineer-in-charge.

M&L for preparing old plastered surfaces and applying two coats of cement base paint on walls including complete removal of existing treatment complete all as per specified and as directed by Engineer-in-charge.

Supply only integral water proofing compound confirming to IS complete all as per specified and as directed by Engineer-in-charge.

M&L for 75 mm thick PCC type D-2, 1:4:8 (using 40 mm graded stone aggregate) in sub base/path etc., complete all as specified and as directed by Engineer-in-charge.

M&L 40 mm thick cement concrete type B1, 1:2:4 (using 20 mm graded stone aggregate) as in floors finished rough, complete all as per specified and as directed by Engineer-in-charge.

S&F Non-skid colour ceramic tiles (600x600) x 7 to 8mm thick in floors/skirting etc set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles over 15 mm thick screed bed or bedding layers in CM 1:6 complete all as per specified and as directed by Engineer-in-charge.

All as per serial item No 30 as above but on vertical surface over and including backing layer of 10 mm thick cm 1:4.

S&F Non-skid colour ceramic tiles (300x300) x 6 to 7mm thick in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles over 15 mm thick screed bed or bedding layers in CM 1:6 complete all as per specified and as directed by Engineer-in-charge.

M&L for Coloured Glazed ceramic tiles surface 350x 450x 7 to 8 mm thick, on vertical surfaces such as skirting, dados and risers to steps etc., set and jointed in neat cement slurry and pointed in white or Coloured cement to match over 10 mm thick screed bed or bedding layers in CM 1:4 complete all as per specified and as directed by Engineer-in-charge.

S & F galvanised mild steel wire cloth, 0.63mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned stacks, or galvanized wire staples complete all as per specified and as directed by Engineer-in-charge.

S & F in repair galvanised mild steel wire cloth, 0.63mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned stacks, or galvanized wire staples complete all as per specified and as directed by Engineer-in-charge.

S & F Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc., complete all as per specified and as directed by Engineer-in-charge.

S & F Anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.)., complete all as per specified and as directed by Engineer-in-charge.

M&L for framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as per specified and as directed by Engineer-in-charge.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads, complete all as specified and as directed by Engineer-in-charge.

S&F 3 mm thick sheet glass of ordinary quality in squares not exc. 0.5 sqm in each pane glazing with oil putty complete all as per specified and as directed by Engineer-in-charge.

S&F 125 mm long extruded Aluminium alloy handles, cast type, anodised, complete all as per specified and as directed by Engineer-in-charge.

S&F 200 mm long Aluminium, anodised, barrel tower bolts of extruded section, complete all as per specified and as directed by Engineer-in-charge.

S&F Mild steel 250 mm sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed, complete all as specified and as directed by Engineer-in-charge.

S&F 125 mm long medium weight, cold rolled mild steel butt hinges, complete all as specified and as directed by Engineer-in-charge.

S&F floor door stopper 14cm long of aluminium alloy body and tongue, anodised with hard drawn steel spring, fixed in floor complete all as per specified and as directed by Engineer-in-charge.

S&F 100 mm long extruded Aluminium alloy handles, cast type, anodised, complete all as per specified and as directed by Engineer-in-charge.

S&F 100 mm long Aluminium, anodised, barrel tower bolts of extruded section, complete all as per specified and as directed by Engineer-in-charge.

S&F 75 mm long medium weight, cold rolled mild steel butt hinges, complete all as specified and as directed by Engineer-in-charge.

S&F exposed GI powder coated snap grid frame work for false ceiling of grid size 600x600mm comprising of wall/cleat angle of size 25x25x0.35mm and cross tee of size 22x35x0.60mm with 1mm dia GI wire as suspender and including 4mm thick prepainted E-Board classic (decorative type) including fixing arrangement from steel truss of any type, complete all as per specified and as directed by Engineer-in-charge.

S&F in repair 300mm dia ordinary rat tail rod pattern springs of mild steel including roller and roller plate for skeletton door shutters complete all as per specified and as directed by Engineer-in-charge.

Dismantling Unframed timber scantlings 40 Sqcm and over in section and in any position, complete all as specified and as directed by Engineer-in-charge.

M&L 2nd class hard wood in scantling wrought timber unframed and fixed, complete all as specified and as directed by Engineer-in-charge.

M&L for 50 mm thick 2nd class hard wood boarding supplied and fixed with nails in any situation (except flooring and skirting) plained both sides with butt joints complete all as per specified and as directed by Engineer-in-charge.

M&L for preparation of wood and wood based surfaces new of any description, exceeding 10 cm width or girth, not otherwise described and applying two coats of creosote oil, complete all as specified and as directed by Engineer-in-charge.

M&L for preparation of new or previously untreated wood or wood based surfaces of any description, exceeding 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and as directed by Engineer-in-charge.

M&L 75 mm thick Cement concrete type C2, 1:3:6 (using 40 mm graded stone aggregate) as in plinth protections/ sub base of floor, complete all as per specified and as directed by Engineer-in-charge.

M&L for forming construction joint 30 mm deep x 10 mm wide filled with sealing compound grade "A", complete all as specified and as directed by Engineer-in-charge.

M&L cement concrete type C-2, 1:3:6 (using 40 mm graded stone aggregate) as in surface channels and drains, complete all as specified and as directed by Engineer-in-charge.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends complete all as specified and as directed by Engineer-in-charge.

Demolition and bracking up 75/100mm bore AC/CI/PVC pipe set in cement mortar complete all as specified and as directed by Engineer-in-charge.

S&F 110 mm dia PVC (SWR) pipes single socketed, in any length, laid in trenches or in floors, complete all as per specified and as directed by Engineer-in-charge.

S&F PVC (SWR) 110 mm bore bends complete all as per specified and as directed by Engineer-in-charge.

S&F PVC SWR vent cowl 110 mm bore complete all as specified and as directed by Engineer-in-charge.

S&F 75 mm dia PVC (SWR) pipes single socketed, in any length, laid in trenches or in floors, complete all as per specified and as directed by Engineer-in-charge.

S&F in repair 32 mm High density polyethylene pipes (HDPE) of pressure rating 6 kgf/sqcm fixed to walls, ceilings or in floors etc. complete all as per specified and as directed by Engineer-in-charge.

S&F in repair Vitreous China squatting pan "Orissa" patern size 580x440mm white with integral foot rest including connection to trap and to flushing pipe, anti-syphonage pipe, etc including 'P' or 'S' trap and provision for lime concrete bedding 1:2 (excluding flushing cistern and flush pipe) complete all as per specified and as directed by Engineer-in-charge.

S&F in repair PVC 10 ltr capacity low level flushing cistern white with inlet ball valve float and braket and 32 mm bore PVC flush pipe, complete all as per specified and as directed by Engineer-in-charge.

S&F in repair 15mm dia PVC connection pipe with PTMT nuts of length 450 mm complete all as specified and as directed by Engineer-in-charge.

S&F in repair 15 mm bore CP fancy type bib taps with wall flange, cast copper alloy, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and as directed by Engineer-in-charge.

S&F in repair 15 mm stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed, complete all as per specified and as directed by Engineer-in-charge.

S&F in repair vitreous china clay wash basin, white, flat back, size 630x450mm excluding taps but including PVC waste pipe 32 mm dia, brackets, waste coupling PTMT(half or full threaded, min weight 45gms) and including pedestal, complete all as per specified and as directed by Engineer-in-charge.

S&F in repair fancy type 15mm dia bore pillar tap cast copper alloy with capston heads chroumium plated, screwed down high pressure with or without lettered Hot or Cold with long screwed shanks and fly-nuts, screwed for iron pipe complete all as per specified and as directed by Engineer-in-charge.

S&F in repair brass chromium plated shower rose 125 mm size with or without swivel joints, any size, including fixing to steel pipe or union, complete all as per specified and as directed by Engineer-in-charge.

S&F in repair Vitreous china urinal, bowl type flat back of size 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60 mm long brass screws complete all as per specified and as directed by Engineer-in-charge.

S&F in repair Urinal spreader of PTMT any colour for fixing with 15 mm dia pipe (Minimum weight = 60 grams) complete all as per specified and as directed by Engineer-in-charge.

S&F 3 mm thick figured glass in squares not exc. 0.5 sqm in each pane glazing with oil putty complete all as per specified and as directed by Engineer-in-charge.

S&F in repair 75mm PVC (SWR) floor trap with grating including jointing with solvent cement complete all as per specified and as directed by Engineer-in-charge.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated or semi-corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 mpa as in roof covering/cladding to wall, fixed with self tapping screws or J hooks, complete all as specified and as directed by Engineer-in-charge.

S&F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 mpa as in roof covering/cladding to wall, fixed with self tapping screws or J hooks, complete all as specified and as directed by Engineer-in-charge.

M&L for RCC (nominal mix) type B-1, 1:2:4 (20 mm graded aggregate) as in lintel etc. including formwork to side and soffits of lintel, complete all as per specified and as directed by Engineer-in-charge.

M&L for RCC (nominal mix) type B-1, 1:2:4 (20 mm graded aggregate) as in Columns, pillars, piers, posts and struts including form work to the side of column, complete all as per specified and as directed by Engineer-in-charge.

M&L for mild steel TMT bars 10 mm dia. and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips, complete all as per specified and as directed by Engineer-in-charge.

M&L for mild steel TMT bars 5 mm to 10 mm dia., cut to length, bent to shape required, in stirrups, spacers and binders and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips quality confirming to Fe-410-S 0r Fe-410-O, complete all as per specified and as directed by Engineer-in-charge.

Dismantling wrought iron or mild steel work of any description not otherwise provided complete all as specified and as directed by Engineer-in-charge.

M&L for MS rolled section of grade Fe-410-0 or Fe-310-0 (beam, tee, angle channel ot flat section) as in roof trusses (framed), trussed purlins, crane gantries rails, and fastening and heavy bracket framing including destance pieces, wind tie, cleats etc., complete all as specified and as directed by Engineer-in-charge.

All as per Serial item No. 86 above but erection and fixing only.

M&L for preparation of new or previously untreated steel or iron surface of any description and applying two coats of synthetic enamel paint over a coat of red oxide, primer over 10cm width or girth complete all as specified and as directed by Engineer-in-charge.

Dismantling of unframed fillets, rails, posts, rafters, purlins etc., under 40 Sqcm in section, complete all as specified and as directed by Engineer-in-charge.

M&L second class hard wood plain fillets, square or rectangular or triangular in section, clean sawn, secured with nails or brads having sectional area exceeding 6 sqcm but not exceeding 13 sqcm complete all as specified and as directed by Engineer-in-charge.

M&L for preparation of new or previously untreated wood or wood based surfaces of any description, not exceeding 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and as directed by Engineer-in-charge.

M&L in repairs in patches for G I Wire netting 0.9 mm dia and 12 mm mesh lathing to wood or metal studding, joists, etc., in walls, ceilings, stanchions, beams, etc., including all laps, cutting and waste, complete all as specified and as directed by Engineer-in-charge.

M&L for preparation of old painted steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying one coats of synthetic enamel paint, complete all as specified and as directed by Engineer-in-charge.

Excavation in post holes (or similar holes) each n.exc 0.5cum in soft/loose soil and getting out, returning filling in and ramming earth or broken rubble mixed with earth around in layers not exceeding 25cm, watering and removing of surplus soil to a distance n.exc 50 meters and making good surface, complete all as per specified and as directed by Engineer-in-charge.

Excavation in trenches n.exc 1.5m wide and n.exc 1.5 m in depth for foundation etc or for shafts, wells, cesspits, manholes, pier holes etc n.exc 10 sqm on plan and n.exc 1.5m in depth and getting out in soft/loose soil complete all as per specified and as directed by Engineer-in-charge.

Returning, filling in, including spreading, leveling, watering and well ramming in layers n exc 25cm complete all as per specified and as directed by Engineer-in-charge.

Removing excavated material not exc. 50 m & depositing where directed at a level not exc. 1.5 m above starting point complete all as per specified and as directed by Engineer-in-charge.

M&L for PCC (1:4:8) type D2 ( using 40mm graded crushed stone aggregate) as in foundation, filling and mass concrete complete all as per specified and as directed by Engineer-in-charge.

S&F MS steel work in tubular trusses including special shaped washers etc., complete using ERW or induction butt welded tubes confirming to IS 1161- 1979 graded St 240 along with one shop coat of zinc chromate primer paint , complete all as per specified and as directed by Engineer-in-charge.

S&F MS plates Fe-410-W(Gde-E-250) quality-A (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment, complete all as per specified and as directed by Engineer-in-charge.

Surface excavation n.exc 30cm deep and averaging 15cm deep and getting out in soft/loose soil complete all as per specified and as directed by Engineer-in-charge.

M&L for hardcore of guage not exc. 63mm deposited, spread and levelled in layers not exc. 15 cm thick, watered and rammed to a true surface of broken stone or boulders, complete all as per specified and as directed by Engineer-in-charge.

M&L for 100 mm thick cement concrete type D-2, 1:4:8 (using 40 mm graded stone aggregate) in sub base in flooring/ hard standing, complete all as specified and as directed by Engineer-in-charge.

M&L 150 mm thick PCC (1:3:6) type C-2 (using 40 mm graded crushed stone aggregate) as in flooring, finished even and smooth without using extra cement, complete all as per specified and as directed by Engineer-in-charge.

M&L for brick work with old size fly ash bricks, straight or curved on plan exc 6m mean radius, built in in CM (1:6), complete all as specified and as directed by Engineer-in-charge.

M&L for preparing newly plastered surfaces of walls and applying three coats of white wash complete all as specified and as directed by Engineer-in-charge.

S&F galvanised mild steel wire cloth, 0.56 mm dia of wire and average width of aperture 1.18 mm and fixed with galvanised wire staples, complete all as specified and as directed by Engineer-in-charge.

S&F Pressed steel frames of size 60 x 125 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., including filling of PCC (1:3:6) in 20 mm graded stone aggregate complete all as per specified and as directed by Engineer-in-charge.

S&F 30 mm thick flush shutters, solid core construction, with particle board core and plywood face panels, commercial type on both sides, complete all as per specified and as directed by Engineer-in-charge.

M&L 30 mm thick second class hardwood glazed and skeleton shutter open rebated and prepared to receive glass, gauge etc edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass and rebated sash bars any numbers etc sizes of member (Bottom 250mm, stiles 100mm, top 120mm & lock rail 160mm wide) as specified in SSR part I section & clause 8.24 (a) complete all as specified and as directed by Engineer-in-charge.

S&F aluminium alloy 250 mm anodised sliding door bolts with hasp, staple (bolt type) & fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast - aluminium alloy, complete all as specified and as directed by Engineer-in-charge.

S&F 150 mm long extruded Aluminium alloy handles, fabricated type, anodised, complete all as per specified and as directed by Engineer-in-charge.

M&L for steel windows with side hung shutter including box type hinges with steel handle and steel peg stay ,complete with glazing bars,dovetailed or welded, complete all as per specified and as directed by Engineer-in-charge.

M&L for steel windows with side hung shutter including projecting type hinges with steel handle and steel peg stay ,complete without glazing bars,dovetailed or welded, complete all as per specified and as directed by Engineer-in-charge.

M&L cement concrete type C-1, 1:3:6 (using 20 mm graded stone aggregate) as in bed block of hold fast etc., complete all as specified and as directed by Engineer-in-charge.

M&L for plastic dividing strip, 38 x 1.5 mm thick and inserted in position to confirm to design, complete all as per specified and as directed by Engineer-in-charge.

S&F screw bolts (machine made) (diameter = 11 to 15 mm) with hexagonal or square head at one end and screwed the other or screwed both ends to be fitted with washers and one hexagonal or square nut exc. 10cm but n.exc. 15cm long MS Work as in bands , straps, supports or stays incl bolts, if reqd. , hold fasts, wall ties and similar small articles conforming to Fe-290 Gde E-165 complete all as specified and as directed by Engineer-in-charge.

M&L for RCC (nominal mix) type B-1, 1:2:4 (20 mm graded aggregate) as in foundations, including rafts, footings, foundation beams, plinth beams, bases for columns, etc. basement slabs, under-reamed piles and mass concrete, complete all as per specified and as directed by Engineer-in-charge.

M&L for bringing earth from outside the MOD land and earth filling under floor in layers not exceeding 25cm thick including ramming and watering complete all as per specified and as directed by Engineer-in-charge.

M&L for form work for side of concrete footings, foundations beam, base of columns & similar works vertical or batter complete all as specified and as directed by Engineer-in-charge.

M&L for damp proof course to horizontal or vertical surfaces including necessary formwork in cement concrete (1:2:4) mix type B-0, 40 mm thick, complete all as per specified and as directed by Engineer-in-charge.

M&L for Polythene film, 150 micron thick, laid on a coat of bitumen primer, @ 0.30 to 0.50 kg per sqm, complete all as per specified and as directed by Engineer-in-charge.

M&L 75 mm thick Cement concrete type C-2, 1:3:6 (using 40 mm graded stone aggregate) in footpath / hardstanding / pavings / plinth protections, finished even and smooth without using extra cement complete all as specified and as directed by Engineer-in-charge.

S&F 15mm dia PVC connection pipe with PTMT nuts of length 450 mm complete all as specified and as directed by Engineer-in-charge.

S&F 15 mm stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed, complete all as per specified and as directed by Engineer-in-charge.

S&F vitreous china clay wash basin, white, flat back, size 630x450mm excluding taps but including PVC waste pipe 32 mm dia, brackets, waste coupling PTMT(half or full threaded, min weight 45gms) and including pedestal, complete all as per specified and as directed by Engineer-in-charge.

S&F fancy type 15mm dia bore pillar tap cast copper alloy with capston heads chroumium plated, screwed down high pressure with or without lettered Hot or Cold with long screwed shanks and fly-nuts, screwed for iron pipe complete all as per specified and as directed by Engineer-in-charge.

S&F fancy type curtain/hanger rods of mild steel pre painted with fixing decorative bracket stops rollers etc complete all as per specified and as directed by Engineer-in-charge.

M&L aluminium door closer hydraulically regulated, designation No. 2, universal type, suitable for door shutters of 701 to 850 mm in width and of weight between 36 to 60 kg and fixed, complete all as per specified and as directed by Engineer-in-charge.

S & F Brass Chromium plated tubular towel rail, 20 mm dia., D Type, 60 cm long between flanges complete all as per specified and as directed by Engineer-in-charge.

S&F towel Ring of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats (Minimum weight 90gms) complete all as per specified and as directed by Engineer-in-charge.

S&F rotational moulded polyethylene water storage tanks triple layered ISI Marked (cylindrical, vertical with closed top) of 500 Ltrs capacity hoisted and fixed in position all as specified and directedin SSR Pt I, complete all as specified and as directed by Engineer-in-charge.

S&F 20mm ball valves, high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed (Minium weight 20mm- 210 gms) and fixed in position complete all as per specified and as directed by Engineer-in-charge.

S&F 32 mm High density polyethylene pipes (HDPE) of pressure rating 6 kgf/sqcm fixed to walls, ceilings or in floors etc. complete all as per specified and as directed by Engineer-in-charge.

Forming embankments incl raising (or lowering) earth spreading in layer n. exe. 30 cm thick, watering, ramming/ rolling and finishing to reqd size and shape, etc, n. exe. 1.5m hing from base complete all as per specified and as directed by Engineer-in-charge.

Dismantling wall and ceiling boards (fibre, pulp, insulation,etc) or insulation board/Slabs/blankets of any thickness including cover fillets, complete all as specified and as directed by Engineer-in-charge.

Taking down carefully aluminum/copper point wiring (light fan, socket or power) complete incl fittings and fixtures such as switches, sockets, light fittings, ceiling rose, pendants, lamp holders, shade conical, regulators etc and separating serviceable fittings for reuse in the same work and removing unserviceable fittings and fixtures with wiring cable, battens, wooden boards etc from site and making good disturbed surfaces of walls, floors, ceiling etc all complete all as specified and directed complete all as per specified and as directed by Engineer-in-charge.

Taking down carefully unserviceable main switches and DB’s including wooden boards and removing from site including making good disturbed surfaces of walls complete all as per specified and as directed by Engineer-in-charge.

Taking down old ceiling fan/exhaust fan and refixing only serviceable fans after testing to its original position/location and handing over old unserviceable ceiling/exhaust fans to MES store yard complete all as specified and as directed by Engineer-in-charge.

M&L for point wiring with 1.5 sqmm size (nominal area) PVC insulated unsheathed single core multi stranded FRLSH copper conductor cable drawn into and incl PVC casing capping sleeves and caps of adequate width and length with all accessories and fittings like bends . elbow crosses etc with PVC round block and PVC terminal boxes with 3.00mm thick laminated sheet cover for mounting fittings etc like switches sockets and fan regulator incl 1.5 sqmm size PVC insulated multistranded FRLSH copper conductor cable as earth continuity conductor and connected to earth dolly complete all as specified and as directed for one light point controlled by one switch, complete all as per specified and as directed by Engineer-in-Charge.

All as per serial item No. 141 above but for one fan point controlled by one switch.

All as per serial item No. 141 above but for one 3 pin 5 Amps socket outlet on independent board.

All as per serial item No. 141 above but for one 3 pin 5 Amps socket outlet on same board.

All as per serial item No. 141 above but with 4 sqmm (nominal area) cable with 4.00 sq mm size copper earth continuity conductor of green colour for 15 A socket outlet on independent boards.

Supply and fix switch socket combination 05/15 Amp 6 pin flush type, complete all as specified and as directed by Engineer-in-charge.

Supply and fix socket multi purpose 2 in 1, 3 pin 5 Amp flush type complete all as specified and as directed by Engineer-in-charge.

Supply and fix switch socket combination 2 in 1, 3 pin, 5/6 Amp flush type universal, complete all as specified and as directed by Engineer-in-charge.

Supply and fix switch piano flush type, 6/5 Amps 240 volts single pole one way, complete all as specified and as directed by Engineer-in-charge.

Supply and fix ceiling rose surface backelite three terminal complete all as specified and as directed by Engineer-in-charge.

S & F stepped type electronic fan regulator flush type on the existing phenolic laminated sheet etc. as reqd., complete all as specified and as directed by Engineer-in-charge.

Supply and fixing LED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose, complete all as specified and as directed by Engineer-in-charge.

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250mm, complete all as specified and as directed by Engineer-in-charge.

S&F PVC rectangular block for mounting, DBs, etc. with 3mm thick plastic laminated sheet cover of size 250 x 200 x 50 mm deep complete all as specified and as directed by Engineer-in-charge.

Supply and fix sheet metal enclosure powder painted for MCB SPN 12 way double door DB with din rail and suitable bus bar complete all as specified and as directed by Engineer-in-charge.

Supply and fix sheet metal enclosure powder painted for MCB SPN 2 way single door DB with din rail and suitable bus bar complete all as specified and as directed by Engineer-in-charge.

Supply and fix MCB SPN 240 Volts 40 Amps breaking capacity 10 KA rating, complete all as specified and as directed by Engineer-in-charge.

Supply and fixing 240V, 10 KA 'B' curve miniature circuit breaker (MCB) of SP capacity 6 to 32 AMP, in the MCB DB Complete with connection testing and commissioning, complete all as specified and as directed by Engineer-in-charge.

Supply and fixing amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) SPN 32 Amps and current carrying capacity in the MCB DB complete with connection testing and commissioning, complete all as specified and as directed by Engineer-in-charge.

Supply and fix 16 Sqmm 1100 volts grade heavy duty cable PVC insulated aluminium conductor, served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 metre apart including 4mm suspension wire, one twin core cable flat or circular including taking down old unserviceable, complete all as specified and as directed by Engineer-in-charge.

Supply and fix 16 Sqmm 1100 volts grade heavy duty cable PVC insulated aluminium conductor, served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 metre apart including 4mm suspension wire, one twin core cable flat or circular, complete all as specified and as directed by Engineer-in-charge.

S&F wall Security light fittings 1x 15 Watt LED New generation energy saving and environmental friendly long life LED street light made up of pressure die cast aluminium housing with high power LED as lighting source and lens embedded PC cover having TOP openning seperate driver compartment with IP65 protection and impact resistance of IK07 and including connection up, complete all as specified and as directed by Engineer-in-charge.

S&F street light bracket made out of GI tubing 25 mm bore medium grade 1.20 Mtr long bend to required shape as in bracket for street light fittings fixed with two pair or MS flat iron 40mm x 5mm size and 30cm long clamp of required shape with bolts nuts and washers suitable for steel tubular pole including painting of mild steel flat iron surfaces with two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed by Engineer-in-charge.

Supply and fix lamp holder, PVC/Polycarbonate type complete all as specified and as directed by Engineer-in-charge.

Supply and fix LED bulb 7 W including taking down old unserviceable one complete all as specified and as directed by Engineer-in-charge.

Supply and fix LED bulb 7 W, complete all as specified and as directed by Engineer-in-charge.

M&L for earthing complete with galvanised steel earth plate electrode of size 600 mm x 600 mm x 6 mm thick buried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of the plate not less than 1.5 mtr below ground level, connected to galvanized earth wire 4.00 mm dia by means of bolts nuts check nuts & washers of galvanized iron or steel , procteded by GI pipe 15 mm bore( light grade) and watering pipe 20 mm bore GI pipe (light grade) and chamber of pcc 1:4:8 type D2 using 40 mm graded stone aggregate and coping shall be in PCC 1:3:6 type C1 using 20mm graded stone agg. 50 mm thick cover of RCC 1:2:4 type B1 using 20 mm graded stone agg. reinforced with 8 mm dia MS tor bar @ 80 mm c/c both ways including excvation and earth work and removal of surplus soil complete all as shown in electrical plate no 3 of SSR PT 1, 2009 with charcoal dust and salt complete and earth lead connected to earthing test point (up to main switches, DBs) including taking down old unserviceable one, complete all as specified & testing on completion. NOTE:- (I) item includes the cost of 7.5 mtr length GI pipe for protection for GI earth wire. (ii) item rates includes the cost of 7.5 mtr earth lead GI earth wire. (iii) PCC pit shall be provided at least 500mm away from the pit and not on the earth pit itself and the extra cost of additional length of watering pipe,bends,elbow etc shall be deemed included in the unit rate.

M&L for earthing complete with galvanised steel earth plate electrode of size 600 mm x 600 mm x 6 mm thick buried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of the plate not less than 1.5 mtr below ground level, connected to galvanized earth wire 4.00 mm dia by means of bolts nuts check nuts & washers of galvanized iron or steel , procteded by GI pipe 15 mm bore( light grade) and watering pipe 20 mm bore GI pipe (light grade) and chamber of pcc 1:4:8 type D2 using 40 mm graded stone aggregate and coping shall be in PCC 1:3:6 type C1 using 20mm graded stone agg. 50 mm thick cover of RCC 1:2:4 type B1 using 20 mm graded stone agg. reinforced with 8 mm dia MS tor bar @ 80 mm c/c both ways including excvation and earth work and removal of surplus soil complete all as shown in electrical plate no 3 of SSR PT 1, 2009 with charcoal dust and salt complete and earth lead connected to earthing test point (up to main switches, DBs), complete all as specified & testing on completion. NOTE:- (I) item includes the cost of 7.5 mtr length GI pipe for protection for GI earth wire. (ii) item rates includes the cost of 7.5 mtr earth lead GI earth wire. (iii) PCC pit shall be provided at least 500mm away from the pit and not on the earth pit itself and the extra cost of additional length of watering pipe,bends,elbow etc shall be deemed included in the unit rate.

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC), complete all as specified and as directed by Engineer-in-charge.

Supply and fix sheet metal enclosure powder painted for MCB SPN 4 way double door DB with din rail and suitable bus bar complete all as specified and as directed by Engineer-in-charge. Note:- The contract sum shall be calculated by deducting the amount shown in Credit Schedule attached to this tender, from total amount of Schedule 'A'/BOQ.

M/S MICROAPPS SOFTWARE PRIVATE LIMITED

M/S JIWA SINGH S GILL

M/s Nice Traders