SPL REPAIR TO BLDG NO T-74, PROVN OF PARKING SHED NEAR BLDG NO T-07 (ADM BLOCK), RADIOLOGY ROOM FOR CTBT AND PROVN OF ELECTRIC POLE AND FLOOD LIGHT FOR BASKET BALL COURT AT SFI AT RMS.

Amount

Dismantling boarding any description fixed in any position with nails

Dismantling Asbestos cement (corrugated, semi corrugated, etc) sheets in roof coverings complete all as specified and as directed.

Dismantling wall and ceiling boards (fibre pulp insulation etc) or insulation boards, slabs, blankets any thickness, incl cover fillets

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all specified and as directed

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified and directed by Engineer-in-charge.

Dismantling of frame work timber scantling 40 Sq cm and over in section in any position complete all as specifed and directed.

Demolition of cement concrete (unreinforced) in ground floors and paving n.exc. 15cm thick (below or above ground level) and removal of rubbish from the site complete all as specified and as directed.

Demolition of brick work or stone/boulder masonry, built in cement mortar including all quions, arches, pillers etc complete all as specified and as directed.

Demolition of unreinforced cement concrete of any description and in any position not otherwise specifically provided for.

Demolition of reed, lathing, single or double, including battens and olaster or chicken wire lathing complate all as specified and as directed.

Taking down cement plaster of any description built in cement mortar on brick or stone walls etc including racking out joints, hacking for Key, scrubbing down with water etc. complete all as specified and as directed.

Taking down chowkats or frames with shutters with exc. 1.5 Sqm but n.exc. 4 Sqm each (without taking of shutters from the frames) complete all as specified and as directed.

Taking down Chowkhats or frames not exc. 1.5 sq. m each Ditto but with shutters (without taking off shutters from the frames)

Taking down and refixing the door in same opening after easing & adjusting of shutters of any description exc 1 sqm and n exc 2 sqm each, without taking down

Surface excavation n.exc 30 cm deep and averaging 15cm deep and getting out in soft and loose soil.

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m depth and getting out in soft/ loose soil complete all as specified ans as directed.

Excavation in post holes (or similar holes) each n. exc 0.50 m and getting out ,in soft/disintegrated rock .

Returning filling in trenches including spreading leveling watering and well ramming in layers not exceeding 25 cm thick all complete all as specified ans as directed.

Removing of excavated material not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point all complete all as specified ans as directed.

M&L for hardcore of gauge n.exc 63 mm, deposited, spread and levelled in layers n.exc 15cm thick, watered and rammmed to a true surface.

Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering

M&L of earth filling under floor well ramming including watering as required Spreading & leveling in layers n.exc. 25cm thick

M&L 2nd class hard wood, clean sawn, in scantling timber frame and fixed with nails complete all as specifed and directed.

M&L 2nd class hard wood plain solid straight chowkats and frames wrought framed rebated on the solid rounded or chamfered put together with glue pined joints

M&L 35 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides

M/L 30mm thick 2nd class hard wood Glazed and skelton shutter, open rebated and prepared to receive glass, gauge etc. devided into squares with plain chamfered or rounded, mitred and rebated sash bars edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc. sizes of members of shutters as specified in SSR Part-I Section-8 clause 8.24(b) complete all as specified.

Supply and fix 35mm thick 2nd class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc. sizes of members of shutters as specified in SSR Part I, Sec-tion 8, clause 8.24 (a) complete all as specified and as directed.

M&L 35 mm thick 2nd class HW plain framed pannelled shutter (any number of panels) with panels of timber flat on both sides or of veneered particle board medium density , wood particle board with commercial face veneers , supplied and fitted to chowkats.

Supply and fix solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube complete all as specified and as directed.

Supply and fix factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded decorative coloured laminates PVC `C` channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and decorative coloured laminates PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail or bottom rail ; panelling of decorative coloured laminates PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC laminated sheet beeding, and joined together with solvent cement, supplying and fixing in the frame at the site as per specification complete all as specified and as directed.

M&L 12mm thick plywood grade BWP type BB fixed with screw to timber frame work complete all as specifed and directed.

Easing of door/windows shutters for easy closing or opening leaf tightening of hinges or changing the position of hinges adjustment of tower bolt, sliding bolt etc complete all as directed.

S&F Rolled sections as in roof truss, purlins including cleats GDE Fe 410-0-or Fe 310-0.

M&L for rolled sections as in framing for clazing and the like fixed with angles cleats and connecting plates with timber foer eaves board complete all as specified and as directed.

S&F bands , straps, supports or stays for rainwater, ventilating pipes, including bolts, if required, hooks (stays) , heavy , for large gates, hooks and pintle hinges, large hasp and staples, chains, hand made sliding bolts, clamps, hold fasts , wall ties, hooks for hanging fans, plain angles cleats for securing purlins to wood trusses or rafters, knee piece inserts, two way and three way straps , palte washers and similar small articles conforming to Fe 290 , Gde E- 165.

M&L for GI frame work size of grid 605 x 605 for seamless ceiling compromising of GI perimeter channel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre / intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with GI Cleat and steel expansion fasteners with and including ceiling section (Not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting lips across the intermediate channel at 457 mm centre to centre.

Supply and fixing as in replacement steel ventilator with top hung shutters including hinges, steel peg stay complete all as specified and as directed.

S&F steel work in tubular trusses including (purlins and rafters) special shaped washers etc complete using ERW or induction butt welded tubes .

S&F mild steel framed work such as grills, gratings etc with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe-290 Gde E-165.

S&F Powder coated of any colour (Thickness or powder coating not less than 50 micron) Anodised aluminium frame for doors, windows ventilators with one or more rebates including joining cleat for fixing etc. complete shall as specified.

M&L for mild steel TMT bars 10mm dia and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips.

All same as per item No 41 above but 6mm to 8mm dia

All same as per item No 41 above but 5mm dia and over and including 10mm dia in stirrups spacers and binders

Use and waste of formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter.

Use and waste of formwork to sides of pillars posts, struts, piers, columns and stanchions finished the suface rough.

Use and waste of formwork to sides and soffits of floors or roof beams, beams haunchings, girders,bressummers lintels, cantilevers, shelves including supports overhangs etc also splays between floors and beams etc.

Use and waste of formwork to chajjas, troughts and similar items including edges.

M&L form work with fair finished to soffits of suspended slabs such as roof slabs, floor slabs, landing and similar work nexc 200mm thick (horizontal or sloping)

M & L for formwork to sides of RCC / PCC bands in walls horizontal or sloping and similar work for rough finished surface of concrete complete all as specified.

M&L for RCC (Nominal Mix) type B1 1:1 1/2:3 (20 mm graded aggregate) as in foundation, including rafts, footings, foundation beams; plinth beams; bases for coloumns, etc basement slabs under reamed piles and mass concrete.

M&L for RCC (Nominal Mix) type B1 1:1 1/2:3 (20 mm graded aggregate) as in columns, pillars, piers, posts and struts.

M&L for RCC (Nominal Mix) type B1 1:1 1/2:3 (20 mm graded aggregate) supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like.

M&L for RCC (Nominal Mix) type B1 1:1 1/2:3 (20 mm graded aggregate) as in chajjas.

M&L for RCC (Nominal Mix) type B1 1:1 1/2:3 (20 mm graded aggregate) as in beams, cantilvers, bressummers, lintels over 1.5m span.

M&L 25mm thick Cement concrete type B-0, 1:2:4 (12.5mm graded aggregate) finished even and smooth without using extra cement.

M&L for PCC 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) as in cills, copings, benching on chajjas, roof kerbs, bed blocks and the like including weathering, slightly rounded or chamfered angles and throating as directed with and including necessary form work complete all as specified and directed.

M&L for Cement concrete for coping above ground level, filling and mass Type B2 (1:2:4) 20 mm grade aggregate complete all as specified and as directed

M & L for PCC 1:2:4 type B- 1 (20mm graded aggregate) as in lintels up to 1.5m clear span, cills, steps, seismic & other similar bands, plinth course, string course, lacing course, parapets & railing up to 60cm in height, copings, kneelers, apex stones, bed plates, kerbs , water trought & the like including weathering, slightly rounded or chamfered angles & throating, as directed

M & L for Precast cement concrete B1 1:2:4 (20mm graded aggregate) as cover slabs for Manholes drains etc including necessary formwork all as specified and directed.

M&L 40 mm thick PCC 1:2:4 type B-0 (using 12.5 mm graded stone agg) as damp proof course to horizontal or vertical surfaces including necessary form works, applying evenly a coat of blown type bitumen at 1.50 kg per sqm and blinding with clean dry sand @ 0.05 cum per sqm including 150 micron thick polythene film laid on a coat of bitumen primer @ 0.30 to 0.50 kg per sqm complete

M&L for RCC Nominal Mix Type B1 1:2:4 (using 20 mm graded stone aggregate) as in slabs.

Material and labour for rendering 15 mm thick plaster in cm (1:6) other side one side of lathing finished even and smooth with out using extra cement cpmlete all as specified and as directed.

Materials and labour for 15 mm thick rendering on brick work in cement mortar (1:6) and finished the surfaces even and smooth without using extra cement complete all as specified and as directed.

M&L for rendering 15mm thick plaster in CM 1:4 on fair faces of brick or concrete work finished the surface even and smooth without using extra cement.

M & L rendering 15mm thick on cement mortar 1:4 mixed with water proofing compound @ 3% of qty of cement finished of brick or concrete work finished the surface even and smooth without using extra cement.. WPC will be measured and paid separately.

M&L for rendering 10mm thick plaster in CM 1:6 on fair faces of brick or concrete work finished the surface even and smooth without using extra cement.

M&L for rendering 5mm thick plaster in CM 1:3 on fair faces of brick or concrete work finished even and smooth without using extra cement as in ceiling.

Supply only integral water proofing compound ( ISI marked )

M&L PCC 1:4:8 type D-2, 75mm thick as in sub base of floor.

M & L PCC (1:4:8) type D-2 using 40 mm graded stone aggregate in foundation, filling and mass concrete complete .

M&L for plain cement concrete 1:3:6 type C1 using 20mm graded crushed stone aggregate as in roof kerb complete all as specified and directed.

M&L for Cement concrete in foundations, filling and mass Type C2 (1:3:6) 40 mm grade aggregate complete all as specified and as directed.

Material and labour for 75mm thick PCC (1:3:6) type C2 (using 40mm graded stone aggregate) as in plinth protection, paving, footpath etc and finished the surface even and smooth without using extra cement complete all as specified and as directed.

Material and labour for PCC (1:3:6) type C2 (using 40mm graded stone aggregate) as in surface channel and like etc complete all as specified and as directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using ex- tra cement, including forms, moulds, mitred /stopped ends etc complete all as specified and directed.

All as per item No 75 above but exceeding 30 cm inner girth upto and including 25 mm girth or part thereof

M&L for brick work with sub class `B' bricks straight or curved on plan exc 6m mean radius built in CM 1:6.

M&L brick work with sub class B bricks straight or curved on plan to any radius in half brick thick walls built in CM 1:4

Supply and fixing as in replacement mild steel galvanized iron wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 and fixed with tinned tacks or staples complete all as specified and as directed.

Supply and fixing 0.71 mm dia and 12 mm mesh lathing to wood or metal studding, joists, etc in walls, ceilings, stanchions, beams etc, including all laps cutting and waste complete all as specified and as directed.

S&F Pre-painted galvalume aluminium zinc coating GI based semi corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall , fixed with self tapping screws as specified .

S & F Pre-painted galvatume aluminum zinc coating GI vased Plain steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self tapping screws as specified.

S & F for 4 mm thick of size 600x600mm HSPC (high pressure Steam Cured) pre-Painted self embossed, textured designer board E-Board Classic to be fixed GI powder coated grid/section size 600mmx600mm with main runner 38x24x0.9mm thick ,cross tee 28.6x24x0.9 mm and wall angle 19x19xo.9 mm duly suspended with 4mm dia GI bar hangers 1200mm centre to centre both ways fixed with steel dash fasteners or from purlin from the roof with alignment clip including providing provisions for light fixtures of any size etc complete all as specified.

Material and labour for non skid ceramic coloured tiles 7 to 8mm thick (Square/rectangular) area of each tile exc 0.06 sqm but n.exc 0.11 sqm coloured in floor etc set and jointed in neat cement slurry and pointed in white cement with pigment to match the shade of tiles over and including 15mm thick screed bed in CM (1:4) complete all as specified and as directed.

Material and labour coloured non skid ceramic tiles 7 to 8mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over and including 15mm thick screed bed of CM 1:4, complete all as specified and directed by Engineer-in-charge..

Ditto all as per item no 85 above but as in skirting over and including 10mm thick cement plaster in CM (1:4) and ditto

M&L coloured Glazed ceramic tiles in vertical surfaces 350 x 250 x 7 mm/ 450 x 350 x 7 mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10mm thick cement mortar 1:4 for fixing of tile complete all as specified and directed.

M&L Machine pressed precast concrete interlocking paver block any shape and size confering to IS 15658-2006 of 60 mm thickness M-35 grade fixed with grey cement and no pigment.

M&L sand cusion for interlocking tiles all as specified and directed.

M & L in repair 110 mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls complete all as specified and directed.

M & L repair for 75 mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls complete all as specified and directed.

S & F 110mm bore PVC (SWR) branch piece single (Single Y equal or unequal) complete all as specified and directed.

S & F in repair 110mm bore PVC (SWR) bends any radius complete all as specified and directed.

S & F 75mm bore PVC (SWR) bends any radius complete all as specified and directed.

S&F of 75dia PVC (SWR) Vent cowl

S & F 75mm dia, PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and as directed.

Taking up or down steel tubing 15mm bore and connections including cleaning for refixing and deposited to stores complete all as specified and directed.

Taking up or down steel tubing 20mm bore and connections including cleaning for refixing and deposited to stores complete all as specified and directed.

Supply and fix 15mm bore galvanised steel water tubing medium grade including all fittings and fixed complete to walls/ceiling or laid in floors complete all as specified and as direcetd.

Supply and fix 20mm bore galvanised steel water tubing medium grade including all fittings and fixed complete to walls/ceiling or laid in floors complete all as specified and as direcetd.

Supply and fixing 20mm bore Gun metal gate valve with iron wheel head and gun metal spindle screwed both ends after and including taking up or down old unserviceable valve complete all as specified and as directed. Make : Leader/Audco/Zoloto.

Supply and fixing 3 mm thick Sheet glass, ordinary quality and glazing with oil putty in square n.exe 0.50 Sqm in each pane after and including hacking out broken glass from wooden/metal surfaces complete all as specified and as directed by the Engr-in-Charge. Make : Modifloat/Ashai/Saint Gobain.

S&F Sheet glass ordinary quality 4.00 mm thick and glazing in aluminum frame in squares n exc 0.5 sqm each

S&F Sheet glass ordinary quality 4.8 mm thick and glazing in aluminum frame in squares exc 0.5 sqm each

Supply and fixing 3 mm thick frosted glass, ordinary quality and glazing with oil putty in square n.exe 0.50 Sqm in each pane complete all as specified and as directed by the Engr-in-Charge. Make : Modifloat/Ashai/Saint Gobain.

Supply and fixing 100mm size stainless steel butt hinges,medium weight, cold rolled complete all as specified and as directed.

Supply and fixing 100mm size mild steel butt hinges, medium weight, cold rolled complete all as specified and as directed.

S&F 75 mm medium weight butt hinges cold rolled mild steel.

Supply and fixing 50mm size mild steel butt hinges complete all as specified and as directed.

S&F 200mm long aluminium anodised barrel tower bolts of extruded section.

S & F Aluminium anodized, barrel tower bolts, 150mm long of extruded section complete all as specified and as directed.

S&F 100 mm long aluminium anodised barrel tower bolts of extruded section.

Supply and fixing 150mm long extruded aluminium alloy handles, fabricated type, anodised complete all as specified and as directed.

Supply and fixing 100mm long extruded aluminium alloy handles, fabricated type, anodised complete all as specified and as directed.

Supply and fixing for 300mm long Mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate complete all as specified and as directed.

S&F in repair soap dish chromium plated stell/stainless steel, approx size 160x160mm x 1mm thick , fixed to walls with plugs & CP brass screws complete all as specified and directed.

S & F in repairs waste coupling of PTMT (half or full threaded) 32 mm dia ,complete all as specified and as directed.

S&F PVC waste pipe, 32mm bore, 750mm long for basin, fixed in repair, complete all as specified and directed.

Supply and fixing as in replacement 125mm dia brass chromium plated shower rose with revolving joints fixed to 15mm bore GI Pipe complete all as specified and as directed. Make :- ESSCO Cat No EOS-542A or equivalent approved make.

Supply and fixing as in replacement brass chromium plated towel rail 600mm long fixed with and including Chromium plated brass screws complete all as specified and as directed. Make : ESSCO Cat No A CN 1111 or equivalent approved make.

S&F towel rail 450mm long of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats (min wt - 170 gms)

S&F for 15 mm bore dia of pipe Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and direcated and as approved by GE.

Supply and fixing as in replacement 100mm dia grating doom with waste hole of PTMT (minimum weight 25gms) complete all as specified and as directed by the Engr-in-Charge. Make: Prayag / Polytuf

Supply & fixing as in replacement 15mm Bib taps, chromium plated cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and as directed by the Engr-in-Charge.

S&F 15mm bore dia bib taps long body cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule.

Supply and fixing as in replacement for 15mm Stop valves fancy type, chromium plated, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed by the Engr-in-Charge. Make : Essco Cat No 513A/513B or equivalent aproved make.

S&F in repairs concealed stop valve, cast copper alloy, with crutch or butterfly handle, screwed down both ends for high pressure, as per ISI suitable for 15mm dia iron pipe all as directed.

Supply and fix as in replacement of 15mm bore pillar tap fancy type, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and as directed by the Engr-in-Charge. Make : Essco, Cat No DLX-508 or equivalent approved make

S&F CP angle cock 15mm cast copper alloy screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions.

S&F in repairs for 15mm dia of pipe Angle valves (concealed type),fancy type and chromium plated screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipes or for Unions and fixed .

Supply and fixed in repair vitreous china wash hand basin including brackets, white size 550 x 400 mm incl cutting cutting for and pinning in ends of brackets. Including Waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other and fixed

S&F in repairs vitreous china water closet (squatt pan) orrisa pattern 580x440 mm size pan white with front or back inlet with integral 'foot rests including provn of lime concrete bedding including connections to 'flushing cistern/pipe complete all as specified and directed including 100mm CI 'P' trap.

Supply and fixing as in replacement 10 litre capacity low level PVC flushing cistern (any colour), syphonic action type, with inlet, ball valve, float, handle, fixed with cast iron bracket (of suitable size) and providing 32 mm dia PVC flush pipe and making all necessary connections complete all as specified and as directed by Engineer-in-Charge. Make : Parryware Model No C-8090 or equivalent approved make of Hindware/Commander.

Supply and fixing as in repair 15mm dia PVC connection pipe 450mm long with PTMT nuts complete all as specified and as directed. Make: Prayag Cat No : 323 or equivalent approved make.

Supply, hoisting and fixing in proper position ISI marked multi-layer rotational moulded polyethylene water storage tank (cylindrical vertical with closed top), of capacity 1000 litres with and including 20mm bore PTMT float and ball valve set including providing necessary connections complete all as specified and as directed by the Engr-in-Charge. Make : Syntex/Polywell/Polycon

S&F ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed in 20mm dia bore pipe.

M&L for providing and fixing Gypsum board 12 mm thick in ceiling fixed with screw as per manufacturers instruction

S&F for depth 0.70m – 1.65 m, DWCPE (SN8) 180 (OD)/163(ID) mm diameter Pipes laid on 150 mm thick PCC 1:3:6 type C-2 including packing under and haunching against the sides of pipes bed with excavation in any type of soil, including manholes/drop manhole of standard size made of Brick masonry/ RCC/Precast RCC with SFRC ventilating cover and frame. Includes all items and activities to execute and make sewer line functional all as specified and directed.

Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless stell cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed

S&F 4 levers brass mortices lock, vertical type, size 100mm

S&F Vitreous China wash basin ovel type table top size 550x400mm

Stainless steel sink, 1.00mm thick for kitchen or laboratory, with plug, waste pipe, washers, including cantilever cast iron brackets, connecting union etc., overall size 495mm x 420mm with bowl size 410mm x 330mm x 160mm

S&F 32 mm dia Low density poly ethylene pipes (LDPE) of pressure rating 6 kg/ cm2 laid in walls/floor.

All as per item No 144 but 40 mm dia

All as per item No 144 but 50 mm dia

M&L 50 mm dia Cast iron floor trap, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4)

S&F 15 mm dia concealed stop valve fancy type CP with long shank and cup complete

S&F for Draperly rod /Harrison rails of stainless steel of 20mm dia with fixing brackets , stops, rollers and rings etc.

M & L Cast iron work grade FG 150, unmachined, in brackets, gully traps, gratings, railing, frames, manhole covers, fire and soot doors, dampers, stop vulve boxes, gate stops,parts of ranges, bulusters and similar articles exc 5kg each

M&L 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite & including 20 mm thick screed bed (bedding layer) in CM 1:4, all as specified & directed.

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations

M&L Raking, cutting and waste on stone slabs/glazed tiles

M&L Circular cutting or notching and waste on stone slab/glazed tiles

M&L for 10 mm thick screed bed or bedding layer in CM 1:3 mixed with water proofing compound @ 3 % by weight of cement on concrete roof surface finished fair and even to maintain the proper slope of roof surface etc complete all as specified and directed.

M&L for Providing water proofing treatment over cleaned roof surface with super thermo APP modified water proofing memberane comprising of the following -

Cleaning of plastered roof surfaces and applying a coat of bitumen primer @ 0.30 kg/Sqm on top of dry surface of finished cement mortar plaster.

One coat of hot blown bitumen of grade 85/25 @ 1.2kg /sqm shall be applied over primed surfaces.

One layer of APP based polymeric water proofing membrane of weight not less than 3 kg/Sqm consisting 3mm thick reinforced with polyster non wove fabric shall be unrolled surfaces with lap of 100 mm and the over lap shall be sealed by flame.

One coat of hot blown bitumen of grade 85/25 @ 1.2kg /sqm shall be applied over polymeric membrane.

Applying two coats of aluminum paint on top of membrane @ 0.10Kg/Sqm.

S&F Aluminium (Die cast) body , Door closer hydraulically regulated, designation No. 2, universal type, suitable for door shutters of 701 to 850 mm in width and of weight between 36 to 60kg and fixed

M&L for preparation of new untreated wooden surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer.

Material and labour for preparation of old wooden surfaces of any description over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed.

Material and labour for preparation of old steel surfaces of any description over 10 cm width or girth and applying one coat of synthetic enamal paint complete all as specified and as directed.

Material and labour for preparation of new steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamal paint over a coat of red oxide zinc chrome primer complete all as specified and as directed.

Writing letters or figures with synthetic enamel paint (Block, Roman, Italic or Indian) not exceeding 30cm high over old painted surfaces complete all as specified and as directed

M&L for preparation of new steel surfaces of any description, n exc 10cm width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide, zinc chrome primer.

M&L preparation of newly plastered surfaces of walls & applying two coats of cement base paint over a coat of alkali resistant primer complete all as specified.

M&L for preparation of old plastered or unplastered surfaces of external wall by brooming down with steel wire brushing and applying one coat of cement base paint on external wall surfaces complete all as specified & directed.

M&L for preparation of new plastered surface & applying two coats of oil bound distemper (OBD) over a coat of white chalktening on wall complete all as specified and directed by Engineer-in-charge.

Material and labour for applying two coats of oil bound distemper after and including complete removal of existing treatment of old plastered surfaces of walls complete all as specified and as directed.

M&L preparing new plaster surfaces of wall and applying three coats of white wash on walls.

M/L for 2 mm thick Birla white putty/JK white wall care putty on walls.

M & L prepration of new treated surface of ceiling and applying two coats of distemper oil emulsion of approved quality with colour over a coat of primer all as specified and directed.

Taking down carefully copper/ aluminium point wiring (light, fan, socket or power) complete, including fitting & fixtures such as switches with board, ceiling roses, pendents, bell/ buzzer, bell push, lamp holders, regulators, sockets, light fittings etc., removing material from site and making good to the disturbed surfaces of walls, ceiling, floors etc. including making good the disturbed surfaces and paint touch up to match with the existing surface complete all as specified and as directed.

M&L for Point wiring complete with two runs of 1.5 sqmm single core PVC insulated FR-LSH cable 1100 volts grade with multi-stranded copper conductors, drawn through and including PVC double locked Casing & caping including provision of 1.5 sqmm, FR-LSH, PVC insulated copper cable as earth continuity conductor connected to common earth dolly, including PVC rectagular box for mounting switches / sockets / regulators etc. with 3 mm thick plastic laminated sheet cover of suitable size as required at site and 50 mm deep complete all as specified and as directed.Make:- Finolex/Richa/RR Kabel Make of caping/casing & PVC boxes :- Prestoplast/Finolex/supreme/Richa

One light/call bell point controlled by one, one way switch .

One Ceiling fan point controlled by one, one way switch.

One 3 pin socket outlet 5 Amps on the same board with other switches.

One 3 pin socket outlet 5 Amps on the Independent board.

All as per item No- 172- here-in-before but with 2.5 Sq mm for 3 pin 15 Amps socket point controlled by one switch on independent board and 2.5 Sq mm copper conductor green in colour as earth continuity conductor connected to common earth dolly complete all as specified and as directed.

M&L Switch socket combination 2 in 1, 5A/16A, 5 in 1 flush type Make :Anchor/Plaza/SSK

M&L for Switch piano flush type single pole, one way 5A Make :Anchor/Plaza/SSK

M&L for switch Socket combination 2 in 1, 5A flush type complete all as specified and as directed. Make :Anchor/Plaza/SSK

M&L for bell push, flush type, 5 Amps Make :Anchor/Plaza/SSK

M&L for replacement of Bell AC 230 volts musical type.Make :Anchor/Plaza/SSK

M&L for stepped type electronic fan regulator 100 Watt socket size flush type on the existing phenolic laminated sheet etc.cn1`r\Make : Anchor/Havells/Legrand/Kinjal

Material and labour for (concelaed Type) point wiring including necessary chese cutting of wall for one light/fan/call bell point with 1.5 sqmm PVC insulated (FR-LSH) unsheathed copper cable multistranded conductor 1100 volts grade controlled by one way switch including 1.5 sqmm PVC (FR-LSH) insulated unsheathed copper cable multistrand conductor 1100 volts grade for continuity earth wire connected to common earth dolly drawn through and including PVC conduit with all accessories and sunk modular GI box for mounting of fittings like switch, socket and fan regulator with modular inner plate and cover plate and making good the distrubed surfaces as per the existing complete all as specified and as directed by the Engr-in-Charge. Note: Red coloured cable shall be used for live connection, black coloured cable shall be used for neutral connection and green coloured cable shall be used for earthing. Separate cable for earthing and neutral to be used for each individual circuit from the distribution board. The Rate of point wiring includes the following :- (i) Copper wire (ii) PVC Conduit with accessoreis (iii) Chase cutting (iv) other accessories such as modular GI box, modular inner plate and modular Cover plate etc Make:- Finolex/Richa/RR Kabel Make of caping/casing & PVC Conduit :- Prestoplast/Richa/superme/Finolex

One light point controlled by one, one way switch .

One 3 pin socket outlet 5 Amps on the same board with other switches.

One 3 pin socket outlet 5 Amps on the Independent board.

All as per item No- 180- here-in-before but with 2.5 Sq mm for 3 pin 15 Amps socket point controlled by one switch on independent board and 2.5 Sq mm copper conductor green in colour as earth continuity conductor connected to common earth dolly complete all as specified and as directed.

M&L for Modular Switch 1 way 6A,1 module Make : Havells/Legrand/Anchor

M&L for modular switch 1 way 16A, 1 module Make : Havells/Legrand/Anchor

M&L for Modular Socket ,6A/2/3 pin combined 2 module Make : Havells/Legrand/Anchor

M&L Modular Socket ,6A/16A-2/3 pin combined 2 module Make : Havells/Legrand/Anchor

M&L for stepped type electronic fan regulator,120 W-2 module Make : Havells/Legrand/Anchor

M&L for ceiling rose 3 terminal PVC/Polycarbonate isolated body complete all as specified and directed. Make : Anchor/Plaza/SSK

M&L for 20W LED, 4', Wall mounted LED batten, extruded aluminium heat sink provided for efficient heat dissipation with all accessories internally pre-wired and fixing the same on and including two Nos PVC blocks and connecting up with flexible copper cable of suitable size from ceiling rose to the light fitting incl taking down old unsv light fitting complete all as specified and as directed. Make : Havells Cat No LHFYBYPNIA1W022(batten) & LHLDDCXCML8P020(LED Tube) or equivalent in Bajaj/Philips

M&L for sub main wiring with two runs of 4.0 Sq mm and one run of 4.0 Sq mm for earth wire with multi standard copper conductors, 1100 volts grade, drawn through and including PVC double locked Casing & caping including complete all as specified and as directed. NOTE:- Two runs of 4.0 Sq mm +one run of 4.0 Sq mm and one run of PVC casing & capping and its accessories of suitable size shall be measured as one unit length.Make:- Finolex/Richa/RR Kabel

M&L for Energy efficient recessed mounted LED luminaire 42W, suitable for 2x2 grid/ armstrong ceiling including provisioning of flexible copper cable of size 0.75 Sq mm 3 core from ceiling rose to the light fitting in the existing space/ by cutting suitable space in false ceiling to mount light fitting with required handing/ fixing arrangement incl taking down old unsv light fitting complete all as specified and as directed. Make : Havells/Bajaj/CG

M&L for LED 1x20W Security light fitting, drawn through including GI bracket of 25mm bore light grade bent to shape and fixed on wall with metal fastners as required and connecting up with flexible copper cable of suitable size from ceiling rose to the light fitting complete all as specified and directed. Make:- Havells Cat No Endurapearl SL20WLLED757SASYTOPCMP /Bajaj/Philips/CG

M&L for Lamp holder , PVC/ Polycarbonate type with PVC round/square block incl 9 watt LED lamp suitable for lamp holder fittings. Make : Anchor/Plaza/SSKke :- Plaza/SSK/Hager Make of Lamp :- Havells/Bajaj/Philips

M&L for modular metal flush box 3 module complete all as specified and as directed Make : Havells/Legrand/Anchor

M&L for modular metal flush box 8 module complete all as specified and as directed Make : Havells/Legrand/Anchor

M&L for modular white cover plate with frame 3 module complete all as directed. Make : Havells/Legrand/Anchor

M&L for modular white cover plate with frame 8 module complete all as directed. Make : Havells/Legrand/Anchor

M&L for MCB Distribution board double door type SPN 8 way, sheet steel, powder painted, with neutral link & earth bar etc. and fixing MCBs of various rating capacity including taking down old unsv MCB DBs complete all as specified and as directed.Make:- Legrand Cat No 507611 or equivalent in ABB/Siemens

Taking down Ceiling fan/Exhaust fan of any sweep carefully from its installed position, dismantling complete, cleaning all dust, applying grease for bearing, painting of fans complete with superior quality synthetic enamel paint by spraying including filling cavaties with filler, after cleaning all dust, reassembling the fan and blades, hanging/ fixing the fan in its original position and testing on completion complete all as specified and as directed.

M&L for TPN DB -VTPN DBs 415 Volts 4 Way wall mounting indoor type adjustable suitable for incoming 4 pole 100/63 Amps MCCB and outgoing SP/TP MCBs with suitable for flush mounting and surface mounting with 100 Amps copper busbar for each phase with 2 nutral bar 2 earth bar and cable ties for meanagement reversible door for IP 43 & IP 54 DBs taking down old unserviceable MCCB complete all as specified and directed by Engr in Charge Make : Legrand or equivalent in ABB/Siemens

M&L for MCB Distribution board double door type TPN 4 way, sheet steel, powder painted, with bus bar neutral link & earth bar etc. and fixing MCBs of various rating capacity complete all as specified and as directed. Make : Legrand Cat No 507885 or equivalent in ABB/Siemens

M&L for MCB TPN 63 Amps, 415 volts, 50 Hz suitable for fixing in MCB DB 'C' seriesc incl taking down old unsv MCB complete all as specified and as directed.Make : Legrand Cat No 408794 or equivalent in ABB/Siemens

M&L for MCB SPN 32 Amps, 230 volts, 50 Hz suitable for fixing in MCB DB 'C' series incl taking down old unsv MCB complete all as specified and as directed.Make : Legrand Cat No 408617 or equivalent in ABB/Siemens

M&L for MCB SP 5-32 Amps, 230 volts, 50 Hz suitable for fixing in MCB DB 'C' series incl taking down old unsv MCB complete all as specified and as directed. Make:- Legrand Cat No 408587-95 or equivalent in ABB/Siemens

S&F sheet metal enclosure with socket plug top and MCBs single pole 32 Amps and neutral encloser with two pin and earth plug and socke complete one single pole MCB including metal encloser all as per specified and as directed by Engr-in-charge. Make :Havells/Legrand/Anchor

M&L for LT UG cable/ service connection of any size and M&L for laying of LT UG cable, XLPE insulated, galvanised steel strip or wire armoured, heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area of 50 sq mm,3.5 core complete all as specified and as directed. NOTE :- (i) Excavation and earth work, sand cushioning, cable protection cover, pipe etc. shall be measured and paid seperately under relevant items. Make : Richa/Havells/Finolex/KEI

All as per item No 205.00 -ditto- but 16 Sqmm 4 Core complete all as specified and as directed.

All as per item No 205.00 -ditto- but 10 Sqmm 2 Core complete all as specified and as directed.

M&L for spread fine river sand in trenches complete all as specified ans as directed. NOTE: For measurement purpose, punned down thickness shall only be taken.

M&L for laying brick sub class 'B' old size burnt bricks for cable protection of size 230mmx115mmx75mm complete all as specified and as directed

Supply & laying tubes ' light grade' galvanised, with all fittings, fixed complete to walls, poles, ceilings or laid in floors/ trenches/ road crossing for protection of cables of size 40 mm dia bore including taking out unsv GI tubing complete all as specified and as directed. Make:- Jindal/TATA/Prakash surya

All as per item No 210.00 -ditto- but size 25 mm dia bore complete all as specified and as directed. Bansal/ Bst/ Jindal/ Nezone (Ntl)/ Prakash/ Tata/ Swastik/ Zenith

S&F 15mm dia steel tubing galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors.

S&F 20mm dia steel tubing galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors.

M&L for cable connection to street light of 1100 volts grade heavy duty cable PVC insulated aluminium conductor, served with inner sheathing of PVC tape and overall PVC sheathed cable flat or circular 4 Sqmm twin core all as specified and as directed. Make : Richa/Finolex/RPG

M&L for PVC pole junction boxes with inbuilt aluminuim bus bar (02 Nos) of suitable size fitted over bus bar insulator and fixing to pole complete all as specified and as directed. Make :Sintex/Hensel/C&S.

S&F for Ceiling fan 1200 mm sweep, 5 star rating including suitable size of fan hook and connecting up with three core twisted flexible copper conductor cable of suitable size upto ceiling rose complete all as specified and as directed.Make : Bajaj/Usha/CG

Supply, installation and commissioning split type air conditioner, 1.5 TR capacity , 5 star BEE rating with cordless remote control unit , in built air ioniser , plasama filter for better indoor air quality with invertor technology inclusive of suction and discharge lines of suitable size of copper tube including necessary brazing and providing nitrile tubing over gas circulating copper tubes and neatly tying the ends with PVC insulating tape, mounting on suitable out door bracket inclusive of suitable drain pipe , complete all as specified and directed.(Spl item) Make : Voltas/Blue star/Hitachi

S&F installation and testing and commissioning of Split type Air conditioner of capacity 1.5 ton rating 3 star with cordless remote operated on 220 Volt AC supply complete to wall with suitable bracket for indoor outdoor unit and connected with electric suply, testing on full load complete all as specified and directed..Make : Voltas/Blue star/Godrej/Hitachi/Hair

Supply installation, testing and commissioning of Refrigerator of capacity 235 Ltrs rating 4 star inverter Direct -cool single door of complete all as specified and directed.Make : Voltas/Blue star/Godrej/Hitachi/Hair/LG

S&f for Electronic Voltage stabilizer, wall mounted type, for automatic operation, single phase ,naturally air cooled, digital display ,indoor type & designed for input variation between 175 V to 260 V with output voltage stabilized at 230V with accuracy of +/- 5% and capacity of 2 KVA including all accessories, complete all as specified and as directed.(Spl item) Make : V-Guard/Microtex/Voltas

Supply & installed voltage stabilizer for automatic operation single phase naturally cooled indoor type & designed for input variation between 130-300V with digital display output voltage stablized at 230V with accuracy of +2.5% and of capacity 4 KVA.Make : V-Guard/Microtex/HI-Tech/Voltas

Supply and erect Steel tubular swaged poles complete with cast iron base plate, finial taper plug, bolts, nuts & screws as specified type 410 SP-22 (9.0 metres long), as per IS-2713 including painting with one coat of black bituminous paint through out internally and externally up to ground level and remaining external surfaces of poles shall be painted with two coats of aluminium paint over a coat of red oxide, zinc chrome primer, complete all as specified and as directed. (Note: Excavation & earthwork , PCC foundation & coping shall be measured & paid separately) Bansal Poles / Calcutta Poles / Jindal Poles / Kwality Steel-Kolkata / National tubing company/Neozne

M&L for LED flood light 180 Watt capacity with high luminious efficiency made up of Epoxy powder coated pressure die cast aluminium housing with elegantly designed heat sink for efficient thermal management, sturdiness and excellent corrosion resistant and lens embedded PC cover having Top Opening seperate driver compartment with IP 66 protection and High quality toughened glass IK07 with 10 KV Built in surge protection device and all connected accessories (for fixing of 4 x LED flood light on one electric pole) including suitable size of serive bracket/angle bar of size 40 x 40 x 6 mm, housing, nuts and bolts etc and making electrical connection complete all as specified and directed.Make: Havells Cat No JETAVALOURFL180WLED757PINTWBLTG/Bajaj/CG/

M&L for earthing complete with galvanized steel earth plate electrode of size 600x600x6mm thick buried directly in ground (earth pit not less than 2.25m deep below the normal ground level) with top edge of the earth plate not less than 1.5 mtr below normal ground level connected to galvanised earth lead wire 4 mm dia as earth lead connectd by means of bolts, nuts, washers and check nuts all as shown in electrical plate No 3 of MES SSR Part-I, including testing on completion complete all as specified and as directed. NOTE:- (i) The unit rate shall also included for earth work in hard/ dense soil, PCC (1:3:6) type C1 chamber with CI cover plate 10mm thick including angle iron frame , funnel with GI watering pipe 20mm dia Medium grade, GI protection pipe light grade 15mm dia and wire mesh complete in addition to item No 1 (a) to (e) of preamble (notes) under sub heading earthing, specified on Sl Page No 389 of MES SSR Part-II. (ii) Earthing lead and GI protection pipe beyond 7.5m will be measured and paid separately. (iii) Test points shall be made of GI strip 32x6 mm bridge type mounted on insulators, where ever applicable

NAGALAND AGENCIES CO

commercial enterprises

P K ELECTRICAL

das enterprises

SHRI MADAN SINGH