SPL REP TO BLDG NO T 09 SPL REP REPL OF BER EXHAUST FAN WALL MOUNTED FAN GEYSERS DESERT COOLERS AND AIR CONDITIONER PROVN OF STATIC WATER TANK CONST OF MAIN GATE FOR KV AT BAIRAGARH UNDER GE BHOPAL

Amount

Note :(i) Please refer Sch A/ BOQ Notes before quoting the tender for all phases/ items mentioned below. (ii) Amount of Schedule of credit shall be deducted offline

Dismantling of asbestos cement (corrugated, semi corrugated etc.) sheets in roof coverings, including ridge complete all as specified and directed.

Dismantling structural steel work including purlins, tursses, etc. complete all as specified and directed.

S&F Steel work in tubular/structural trusses, purlins, etc including special shaped washer etc complete using ERW or induction butt welded tubes conforming to IS.1161-1979 grade St.-240 or steel sections conforming to Fe 410-W (Gde E-250) quality -A complete all as specified and directed.

M&L for mild steel work, angle iron, flat iron, MS plates as in brackets, cleats, fastners, wind ties, supports, base for posts etc with riveted, bolted or welded attachment complete of Fe-410-W (Gde-E-250) quality-A complete all as specified and directed.

M&L for preparing new or untreated steel & iron surfaces of any description over 10cm in width or girth and applying two coat of synthetic enamel paint over a coat of zinc primer complete all as specified and directed

S&F pre- painted galvalume aluminum zinc coating GI Based corrugated steel sheeting 0.50mm thick, 150 Az, of an colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, chajjas, fixed with self tapping screws complete all as specified and directed.

S&F Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick, 150 Az, of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

Dismantling of wall and celing hard boards/AC sheets and plywood in any thickness & any position including cover fillets complete all as specified and directed

M&L for galvanised cold rolled steel section frame work size 600x600mm grid size using 24 x 38 x 0.50mm (composite thickness) tee (bottom pre-coated) and 24 x 24 x 0.50mm (composite thickness) wall angle galvanised cold rolled steel section including suspenders as per (Gabsec) manufacturs instruction as in ceiling all as specified and direcetd (Make : GABSON (Gabsec) or equivalent as approved by the GE)

M&L for Asbestos free calcium silicate board of size 600 x 600 x 4 mm thick decorative type fire resistant, moisture resistant and tested as per IS 14862-2000 fixed to steel frame work as in ceiling, including applying two coats of oil bound distemper all as specified and directed.

Dismantling of stone slabs and tiles of any description or thickness in floors, aprons etc laid bedded and pointed in any mortar complete all as specified and directed.

M&L for dark shade vitrified ceramic tiles 10 mm thick (square/rectangular) polished, area of each tile n. exceeding 0.36 sqm in floors etc. over and including 20mm thick screed bed in cm 1:6 set and jointed in neat cement slurry and pointed in epoxy adhisive complete all as specified and directed.

Demolition of cement concrete in ground floor, (unreinforced) paving nexc 15 cm thick (below or above GL) complete all as specified and directed

M&L for Cement concrete 1:3:6 type C2 using 40mm graded stone aggregate in plinth protection, 75mm thick, finished even and smooth without using extra cement, including making joints 12mm wide to the full depth of PCC at every 3 metres and at every change of direction and filling the same with & including bitumen and sand 1:3 by weight complete all as specified and directed.

M&L for cement concrete 1:4:8 type D-2 (using 40 mm graded stone agg) as in foundation, filling, subbase and mass concrete complete all as specified and directed.

Taking down chowkats or frame nexc 1.5 sqm each with shutters (without taking off shutters from the frame) complete all as specified and directed

S&F 125X60mm pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges lock strike plate etc complete as specified made out of 1.25mm thick MS Sheet complete all as specified and as directed.

M&L for cement concrete Type B-0, 1:2:4 using 12.5mm graded stone aggregate as in filling of door frames of pressed steel and in bed blocks and like etc complete all as specified and as directed.

S&F factory made solid PVC moulded door shutter with particle board core 28 to 30 mm thick (style) with 2,4, or 6 raised panel design with 2mm thick moulded prelam PVC sheet on the front face and 2mm plain colour PVC sheet on back face complete all as specifed and directed.

S&F factory made PVC moulded shutter but wire gauzed i.e. Panel will be of wire gauze in lieu of wood grain printed PVC sheet panel . The wire gauze shall be wrapped on an additional square 8mm MS solid tube and this tube shall be welded to MS tubes. The wire gauge shall be stretched to tighten firmly.

S&F in Window ECO 4000, of double rebate openable/fixed window made of galvanised steel colour coated/powder coated (base steel as per IS 513 Of 'D' quality, galvanised as per IS 277 with zinc of 120 gms/sqm) with total thickness of coating 0.58 microns thick and back coated with alkyd backer 5-7 micron thick or powder coated with pure polyster powder up to 50-60 micron thick. Outer frame section 72 x 55 mm , center mullion section 72 x 50 mm, shutter section 47 x 20 mm, fly mesh section 40 x 20 mm and the fixed glass beading section 12 x 12 mm, outer frame and mullions shall consist rebate for glazed shutter, fly mesh and 20 mm provision for guard bars/grills, the section cut to length mitre joined with corner bracket, center millions fixed with mullions cap, stay, handle, latch, 2 nos of heavy duty stainless steel pivot hinges per shutter and paneled with 5 mm thick plain float glass and S. S. mesh for fly mesh shutter (304 grade), fitted using EPDM (Ethyl Propyelene Diamine Monomer) gaskets including fixing windows in the concrete/masonry wall by means of self expanding screws, including 10mm square bars welded to 6x12mm flat at a distance 150mm C/C (pitch) etc. complete all as specified and directed. Make : NCL Allek Seccolor Ltd (Model :ECO 4000) or equvalent as approved by GE)

M&L for Providing and fixing fixed louvers fabricated from Roll formed sections made of galvanized Steel colour coated/powder coated (base Steel as per IS 513 ‘D’ quality, galvanized as per IS 277 with zinc of 120 grams/Sqm) with thickness of 0.58mm coated sections to be primer coat of epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with alkyd backer of 5-7 microns or powder coated with pure polyester powder up to 50-60 microns thick, section for external frame 33 x 58 mm, glass holding flanges made of polypropylene, sections are to be cut to length, mitre joined with corner bracket. The above frames should be fixed to the concrete/masonry walls by means of self expanding screws complete all as specified and directed.

S&F Solid PVC door frame of size 50 mmx 47mm made out of 5 mm plain colour PVC sheet reiforced with MS square tube and fixing in opening as per manufacturer instruction complete all as specified and directed.

S&F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width struck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rail on either side and gap insert for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles and rails with suitable PVC sheet beading and jointed together with solvent cement supplying and fixing in the frame at site as per specification & drawing complete all as specified and directed.

S&F 200 mm Aluminium anodised barrel tower bolts extruded section and fixed complete all as specified and directed

S&F 250mm long aluminium alloy anodised sliding door bolts with hasp stapple (bolt type) and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and as directed

S&F 100 mm mild steel butt hinges medium weight,cold rolled complete all as specified and directed

S&F 150 mm Aluminium handles, cast type, anodised complete all as specified and directed

S&F Galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperure 1.18 mm and fixed with tinned tacks, or galvanised wire staples fixed complete all as specified and directed.

M&L for preparation of new or previously untreated wooden surface of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and as directed.

M&L for Mild steel TMT Bar 6mm to 8mm dia and over cut to length, bent to shape to required, including cranking, bending spirally for hoping for columns, hooking ends and binding with and including mild seel wire (anneled ) not less than 0.9mm dia or securing with clips quality confirming all as specifed and directed.

Demolition of brick work, built in Cement mortar including all quoins, arches, pillars etc complete all as specified and directed.

Taking down cement plaster on brick or concrete surfaces, including wall tiling if any, racking out joints, hacking for key, scrubbing down with water complete all as specified and directed.

M&L for brick work with fly ash bricks (modular size bricks), straight or curved on plan exc 6 m mean radius, built in CM 1:6 complete all as specified and directed.

M&L for brick work with fly ash bricks (modular size bricks) straight or curved on plan any radius in half brick thick walls, built in CM 1:4 all as specified and directed.

M&L for 15mm thick rendering in CM 1:6 on brick/concrete surfaces including finishing the surfaces even and smooth (without using extra cement) complete all as specified and directed.

M&L for 15mm thick rendering in CM 1:4 on brick/concrete surfaces including finishing the surfaces even and smooth (without using extra cement) complete all as specified and directed

M&L for preparation of newly plastered or unplastered surfaces of walls and applying two coat of acrylic exterior water base emulsion paint on walls over a coat of waterproof putty complete all as specified and as directed. Note: Putty shall be measured and paid for seperately under respective item

M&L for applying one coat of white wall care putty 3 mm thk on walls complete all as specified and directed. Make- Birla / JK putty

M&L for preparation of newly plastered or unplastered surfaces of walls and applying two coats of oil bound distemper over a coat of cement based putty complete all as specified and as directed. Note: Putty shall be measured and paid for seperately under respective item

M&L for Hardcore of Broken stone or boulders of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for Factory made, machine pressed, M-40 grade concrete interlocking paver blocks (glossy/reflective type), with grey cement and pigment, any shape and size conforming to IS:15658-2006 (ISI Marked) of 100 mm thickness with & including 50 mm thick sand cushion and joints filled with sand complete all as specified and directed.

M&L TMT steel bars 8 mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hookings ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

Excavation in trenches n exc 1:5m wide n exc 1.5m deep and getting out in hard/dense soil complete all as specified and directed.

M&L for reinforced cement concrete (Nominal mix) type B1, 1:2:4 20 mm graded stone aggregate) in foundation, footings, plinth beam, base of column etc complete all as specified and directed.

M&L for reinforced cement concrete (Nominal mix) type B1, 1:2:4 ( 20 mm graded stone aggregate) for column, pillar, post and strut etc all as specified and directed.

M&L for reinforced cement concrete (Nominal mix) type B1, 1:2:4 (20 mm graded stone aggregate) for beam etc all as specified and directed.

M&L for TMT steel bars 10 mm dia, and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hookings ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

Use and waste form work to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundaiton and plinth beams ; and similar work; vertical or to batter complete all as specified and directed.

Use and waste form work to sides of pillar, column, finished surface of concrete etc complete all as specified and directed.

Use and waste form work to sides of roof beam, and similar work complete all as specified and directed.

M&L for Framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe-290 Gde E-165 for ornamental and intricate design complete all as specified and directed.

M&L for Granite 20mm thick (of any type) work (table rubbed) and polishshed( in cooking platform, steps, jambs, pillar and like i including pointing pointing in white cement 1:2 using marble dust with admixture of pigment to match with shade of granite over and including 15 mm screed bed in cm 1:4 complete all as specified and directed.

Returning filling in including spreading levelling, watering and well rammming in layers n exc 25cm in soil complete all as specified and directed.

Removing excavated soil to a distance exc 250 m and not exc 500 m depositing where directed at a level n.exc 1.5m above the starting point complete all as specified and directed

Use & waste of Formwork to faces of walls, retaining walls, abutments, parapets and staircase railings and similar works including attached pillasters, buttresses etc, vertical or batter complete all as specified and directed.

M&L for reinforced cement concrete (nominal mix) in Type B1, 1 :2 :4 (20 mm graded aggregate) as in walls, retaining walls, basement walls, ballast walls and the like; any thickness; above top of footings, including attached pilaster and buttresses, complete all as specified and directed.

Supply only liquid water proofing compound complete all as specified and directed.

M&L for Mild steel round bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips of Fe-410 W Gde , E-250 Quality A complete all as specified and directed.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc. complete all as specified and as directed.

M&L for Point wiring using approved colour coding as per IS (Red, Black and Green for single phase circuits), with multi-stranded copper conductor -stranded copper conductor 1.5 Sq. mm nominal cross-sectional area, single core, PVC insulated and unsheathed FRLS cable 1100 volts grade, ISI-694 marked with valid CML No. in and including medium grade, PVC concealed conduit and conduit accessories concealed in wall/roof/floor etc, ISI marked with valid CML No.(IS-9537-1983 for conduits and IS:3419:1976 for conduit accessories), with mild steel/pressed steel sunken boxes( with earth dolly) duly painted with two coats of anti corrosive paint/aluminium paint over a coat of red oxide primer internally, and two coats of black bituminous paint over a coat of red oxide primer externally, covered with 3 mm thick plastic laminated sheet cover for fixing of switches, sockets and fan regulators etc, including PVC insulated multi-stranded copper conductor 1.5 Sq mm nominal cross sectional area single core FRLS cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed at site for the following:- One light /Fan/Exhaust/bell point controlled by one switch.

All as per item No 61.00 above but for One 3 pin socket outlet 5 Amps on independent board complete all as specified and directed.

All as per item No 61.00 above but for One 3 pin socket outlet on same board complete all as specified and directed.

All as per item No. 61.00 here-in-before but wiring with 2.5 Sq mm copper cable for 5/15 amp switch socket on independent board and provision of 2 Sqmm, FRLS insulated multi-stranded single core earth wire for earth continuity, connected to common earth dolly complete all as specified and directed.

S&F Polycarbonate switch piano, flush button, single pole, one way 5 Amp , 240 volts ISI marked, complete all as specified and directed

S&F ceiling rose, surface type, 3 terminal, 240 V complete all as specified and directed

Supply and fixing Polycarbonate socket outlet 2-in-1, 5 pin 5 Amps, 240 volts, flush type complete all as specified and directed

S&F with socket outlet flush type multipurpose 2 in 1, 5 pin 5 and 15 Amp, 230 volts complete all as specified and directed

S&F Polycarbonate switch piano flush button single pole one way 15 Amp 240 volt ISI marked, complete all as specified and directed

Taking down old unserviceable sub main wiring of any size and any discription all complete all as specified and directed

M&L for Sub main wiring with two single core FRLS PVC insulated unsheathed cable 1100 volts grade, 6 Sqmm size with multistranded copper conductor, drawn in non metallic rigid PVC conduit of size 25 mm dia ISI marked including PVC insulated unsheathed 6 Sqmm cable with multistranded copper conductor green PVC insulated as continuous earth conductor cable connected to earth dolly complete all as specified and directed

Taking down existing unserviceable fitting any type any size and Supply and fixing LED lights fitting 1x 20 W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed

Taking down existing unserviceable light fitting patti type and S&F LED 20 watt recess mounting light fitting (2 x 2 luminaire) , with white powder coated CRCA housing with high power LEDs and aluminium front frame with flat white high power transmission acrylic cover including connecting with PVC insulated multistranded copper flexible cable 0.5 sqmm two core, and PVC round block white colour x 2 Nos for mounting of fitting complete all as specified & directed. Make :-Surya Cat Part No SLE DS 20 11R-ASTRUM or equivalent in Philips/ HAVELLS/BAJAJ.

Taking down main switches/MCB DBs of any capacity/type including MCBs.

S&F sheet metal enclosure for MCB, DB, VTPN 415 Volts 200 amps rated busbar 4 way Double door enclosure made up of CRCA sheet steel, RAL 9003 powder coated, IP 43 with MCB as incommer and MCB SP/TP in outgoing complete all as specified and directed.

Supply and fixing 415V 125 Amps, 3 pole and current carrying capacity in the VTPN DB complete with connection testing and commissioning complete all as specified and directed.

S&F MCB SP 240 volts 6 to 32 Amps, 10 KA breaking capacity, 'B' Curve including connection with suitable size aluminium / copper lugs complete all as specified and directed.

S&F MCB SPN 240 volts 32 -40 Amps, 10 KA breaking capacity, 'c' curve including connection with suitable size aluminium / copper lugs complete all as specified and directed.

S&F sheet metal enclosure for MCB, DB, SPN, 240 Volts, 200 amps rated busbar, 8 way Double door enclosure made up of CRCA sheet steel, RAL 9003 powder coated, IP 43, including wooden rectangle board of first quality of suitable size for mounting of DB box complete all as specified and directed.

Taking down & Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor.(BLDC) with hook for hanging ceiling fan complete all as specified and directed. MAKE: CROMPTON ENTRUST 50 OR EQUIVALENT IN BAJAJ,HAVELLS. Note: Old fan shall be deposited to AGE E/M Yard.

Taking down and servicing/greasing/painting of ceiling fan of size 1200mm sweep and refixing in position including provision 3 core flexible PVC insulated multi stranded copper conductor of size 0.5 sq mm from ceiling rose/ connector to fan with replacement of capacitor complete all as specified and directed.

M&L for Earthing complete with galvanised steel earth plate electrode 60×60cm×6mm thick, buried directly in ground (earth pit not less level) with top edge of the plate not less'than 1.5 metres below normal ground level, connected to galvanised iron earth wire of 4 mm as earthing lead by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 SSR including earth pit in any soil char coal common salt , 15 mm all around earth plate PCC (1:3:6) type culprit, with 40 x40x6 mm angle iron frame and PCC cover (1:2:4) type B1 , water pipe funnel and GI protection pipe light grade 15mm dia upto panel connecting earth lead to panel all as specified and directed by EIC. Note : Earth continuity conductor including protection pipe up to 7.5 mtrs from earth electrode will be included in unit rate.

Excavation in trenches nexc 1.5 mtr wide and n exc 1.5 mtr in depth and getting out in soft/ loose for laying cables, erection of poles complete all as specified and directed.

M&L for sand filling with clean dry fine sand unwashed including gently punning around cables in trenches for cable protection (8 cm below cable & 15 cm above cable) complete all as specified and directed. [Note:-Compacted/punned thickness shall be measured & paid]

Supplying and laying sub class 'B' bricks (modular) for cable protection cover laid flat and dry in trenches over the cable perpendicular to the direction of cable complete all as specified and directed

Takng down old unservicable cable and Supply and Laying XLPE insulated, PVC sheathed, armoured, heavy duty electric under ground cable, with stranded aluminium conductor, 1100 Volts grade of size 25x3.5 sqmm, laid in trenches/floor or fixed on wall/pole complete all as specified and directed.

S&F GI Tubes, 'light grade' galvanised, with all fitting and laid in floors, under road, pavement or hard standing steel water tubing bore of tube 25 mm complete all as specified and directed

Cutting of cast iron pipes in position for insertion of new tees , branches, etc for 80 mm bore complete all as specified and directed :-

S & F for CI fittings i.e bend (any type, radius and angle) tapers any type, (straight bend including decreasing or double socket etc) Tee pieces single branch,'Y' junction, (all sockets or socket and spigot or flanged) collars, caps and plugs. for spigot socketed pipes upto 150 mm bore (Make : Kapilance/ LNT/ Necco/Kajeriwal/Kesin)

M&L for run lead joint for spigot and socketed end CI pipe & fittings complete all as specified incl excavation, returning & refilling and directed by Engr in charge for 80 mm bore

Ditto but for 100 mm bore

Ditto but for 150 mm bore

Supply and fix cast iron flanged sluice valve of class 1.6 PN, long body, ISI marked, conf to IS-14846 with stainless steel spindle and hand wheel including nut bolts, rubber gasket complete for installation of valve all as specified and directed by EIC for 80 mm bore : (Make : KIRLOSKAR / LEADER / L&T)

M&L for brick with sub class B brick straight or curved on plain exc 6 Mtr mean radious built in cement mortar 1:4 complete all as directed (For repairing of old broken chamber )

M&L for PCC 1:2:4 type B1 using 20 mm stone aggregate as in coping/support both including necessary form work etc complete all as directed

M&L for framed work for valve pit chamber cover made of mild steel equal angle and MS sheet 3 mm thick including welding, cutting, hinges, locking arrangments including painting complete all as specified and directed.

S&F & laying only GI tubing 50 mm bore medium grade ISI Marked with one socket both end threaded in any length including cutting threading connection in new or old position and all type of GI new fittings for laid in trenches/wall/ceiling/ floor/ all as specified and directed.

S&F 50 mm bore Gun metal globe or gate valves, conf to IS 778 with iron wheel head, screwed both ends for iron pipe and fixed in existing or new position (Make : Leader/ Zoloto/ Sant/ Ramco)

Ditto but for 25 mm bore

Ditto but for 20 mm bore

M&L for point wiring complete for one switch socket combination 5/6 amp on independent board with cable 1.5 sqmm (Nominal area) FRLS PVC insulated multistranded unsheathed copper conductor, drawn in concealed PVC conduit should not less than 20 mm dia and including juction covers and junction boxes , sunken cast iron/ pressed steel terminal boxes duly grouted in bricks cement or wooden planks wall and painted with red oxide metal primer for mounting of switches, sockets,fan regulator with 3 mm thick plastic laminated sheet top cover fixed with brass screwed and cup washers including making good to disturbed surfaces of wall in CM 1:3 with white/colour wash as per adjoining specifications including provision of continuous earth continuity wire of 1.5 sqmm copper PVC insulated insulated FRLS cable for one light/ fan point controlled by one switch and connected to common earth dolly, complete all as specified and direced by the Engineer in charge.

All as per Srl item No. 101.00 here in before but for one switch socket combination 6 pin 5/ 15 Amps on independent board with wire of size 4 Sqmm and 4 Sqmm as earth wire.complete all as specified and directed by Engineer - in - Charge.

Supply and fix sheet metal enclosures with socket plug top and MCB's with two pin and earth plug and socket complete with one Single pole MCB 240 V grade 25 Amp complete all as specified and directed .

S&F Voltage stabilizer for automatic operation, single phase naturally air cooled indoor type & designed for input variation between 170 V to 270 V with output voltage stabilized at 230 V and of capacity 5 KVA all as specified and directed by EIC. Make-V-Guard Modal-VG500/ equivalent in Microtek/Vintak as Approrved by GE.

S&F steel body exhaust fan AC three phase 230/240 volts of size 300 mm sweep with louver all as specified and directed by EIC. Make-CG Modal DRIFTAIRPLUS120PW or equivalent in Havells/Usha Approrved by GE.

S&F water heater strorage type,electricity capacity 25 litrs BEE 5 star rated with advanced safty features all as specified and directed by EIC.Make-V Guard Model-Divino ,Havells,CG or Equivalent Approrved by GE.

S&F desert cooler electric driven (single phase) having nominal air flow capacity of 4000 cum per hour (or nearest size) plastic/PVC boby size 61x40.5x120 cm tank cap 75 ltr power-190 watt suitable for 550 sqft area ,high density honeycomb pads, control type manual and remote type all as specified and directed by EIC.Make-CG Model OZONE or Equivalent Approrved by GE.

S&F air cooled air split unit air conditioner Inverter type electric driven (single phase) capacity of 2 TR BEE 5 star rated with Dist filter, copper condenser coil with suitable stand all as specified and directed. Make-Bluestar Model-IA524DLU /Daikin/Carrier or Equivalent Approrved by GE.

Deduct Schedule of credit (calculation will be done off line) Rs. 23800.00

M/S Shanti Traders

PADAMSHRI CONSTRUCTION CO

CREATIVE CONSTRUCTION

RAJPATI CONSTRUCTION

Samaksh Enterprises

Nakoda Constrcution Company

M/S SURINDER KUMAR MAHAJAN