GE U(N) 28 2022 23 SPECIAL REPAIR TO BUILDING NO P5 ALONG WITH ADDITIONAL ALTERATION TO BUILDING NO NP23 INCLUDING CERTAIN SANCTION WORKS IN VARIOUS LOCATIONS OF SUB AREA UNDER GE (N) UDHAMPUR

Amount

M&L for surface excavation not exc 30cm deep and averaging 15cm deep and getting out in hard/ dense soil complete all as specified and as directed by Engineer-in-Charge.

M&L for excavation in trenches n.exc 1.50m wide and n.exc 1.50m in depth in foundation in hard/ dense soil and getting out complete all as specified and as directed by Engineer-in-Charge.

M&L for returning, filling in trenches, filling under floor including spreading, levelling, watering and ramming in layers not exc 25cm in hard/ dense soil complete all as specified and as directed by Engineer-in-Charge.

M&L for removing excavated material n.exc 50m and depositing where directed at a level n.exc 1.5m above the starting point complete all as specified and as directed by Engineer-in-Charge.

M&L for hardcore of gauge exc 63 mm but n exc. 100 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rolled/rammed to a true surface complete all as specified and directed by Engr-in-Charge

M&L for reinforced cement concrete, design mix as in beams/bends supported on walls, beams and columns in floor, roofs, landings, balconies, canopies, shelves and like complete all as specified and directed by Engr-in-charge.

M&L for reinforced cement concrete, design mix as in slab supported on walls, beams and columns in floor, roofs, landings, balconies, canopies, shelves and like complete all as specified and directed.

M&L for providing plain cement concrete 1:2:4 type B-1 Using 20 mm graded stone aggregate as in kerb and in similar works bedded and jointed in CM 1:6 including necessary exc if necessary complete all as specified and directed by Engr-in-charge.

M&L for providing plain cement concrete 1:2:4 type B-1 (20mm graded crushed stone aggregate) as in coping incl necessary formwork, complete all as specified and as directed by Engineer-in-Charge.

M&L for providing plain cement concrete type B-0 1:2:4 (12.5 mm graded aggregate) set in cement mortor 1:4 louvers and jallies, 35 mm thick (measured solid), including all moulding but excluding frame complete all as specified and directed by Engr-in-charge.

M&L for pre-cast cement concrete 1:2:4 type B-1 (20mm graded aggregate as in cover slabs for manholes etc) chullah hoods chajjas, water troughs, mangers shelves and similar articles with plain faces incl all moulding but excluding frame and in similar works beded and jointed in cement mortar 1:4, including necessary form work complete all as specified and as directed by Engineer-in-Charge.

M&L for plain cement concrete (1:4:8) type D-2 using 40mm graded aggregate as in drain foundation complete all as specified and as directed by Engineer-in-Charge.

M&L for brickwork with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius built in CM(1:6) with old size bricks complete all as specified and as directed by Engineer-in-Charge.

M&L for brick work with old size sub class 'B' bricks, straight or curved on plan exc 6m men radius built in cement mortar 1:4, complete all as specified and as directed by Engineer-in-Charge.

M&L for brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls, built in CM 1:4 complete all as specified and directed by Engr-in-Charge

M & L for formwork to sides and soffits of suspended slabs such as roof slabs, floor slabs,beams landings and similar work; not exceeding 200mm thick (Horizontal or sloping)complete all as specified and as directed by Engineer-in-Charge.

All as per SI NO 16 but edges of slab exc 10cm but not exc. 20cm wide complete all as specified and directed.

M & L for formwork to sides and soffits of floor or roof beam, beam haunching girders, bressum-mers, lintels cantilevers, shelves including supports,overhangs etc also splays between floors and beams, etc complete all as specified and directed by Engr-in-charge.

M&L for TMT bars 8mm dia and over cut to length bent to shape required including cranking bending spirally for hopping for columns,hooking ends and binding with and including MS wire (annealed) not less than 0.90 mm dia confirming to TMT bars complete all as specified.

M&L for Mild steel TMT bars 5 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed by Engr-in-Charge

M&L for dismantling of Asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings complete all as specified and directed by Engr-in-charge.

S&F Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by Engr-in-charge.

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by Engr-in-charge.

S&F false ceiling with fibre cement designer tile ivory painted (high pressure steam cured) of 4 mm thickness (as per IS:14862) of size 595 x 595 mm and any one of the desin (occeanic, lake & hill,cascade or electra) in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 gms, both side inclusive) consisting of main 'T' runner with suitably spaced joints to get required length, and 15x32 mm made of 0.30 mm sheet, and cross'T' at 600mm c/c to form a grid including, required cutting/making, opening for services like diffusers,grills,light fittings, fixures,smoke detectors etc . Main 'T' runners to be suspended from ceiling using GI soffit cleats fixed to existing rafter, purlin, etc with gavanised Butterfly level clips, spaced at 600 mm c/c along main T, bottom exposed width of 15 mm of all T- sections shall be centra black pre-painted with polyester paint, and having a load bearing capacity of 12 kg/sqm, and refixed all exesting electric wiring and fixture all complete at all heights as per direction of Engineer-in -Charge.

M&L for taking down exsiting water proofing treatment incl PCC padding, plaster, etc complete necessary removal of debries from sitecomplete all as specified and as directed by Engineer-in-Charge.

M&L for 40 mm thick PCC (1:2:4) type B-0, (using 12.5 mm graded crushed stone aggregate) in two layers (each 20 mm) with chicken mesh provided between the layers and finished even and smooth with false grooves @ 450x450 mm complete all as specified and as directed.( Note: Chicken wire mesh shall be measured and paid separately under respective item of sch 'A").

M&L for galvanised steel wire cloth size of 20 mm but 0.36 mm nominal dia of wire and average width of aperture 1.40mm complete all as specified and directed by Engr-in-charge.

M&L for 10mm thick cement plaster on fair face of concrete surface including repair of doubing roof surfaces in CM 1:3 finished even and smooth without using extra cement over complete all as specified and directed.(Water proofing compound shall be measured and paid seprately )

Supply only integral water proofing compound complete all as specified and directed by Engr-in-charge.

M&L for preparing RCC roof slab top by wire brushing and cleaning the dust and forign materail etc complete and applying a coat of hot blown bitumen 85/25 grade @ 1.20kg/Sqm over a coat of bitumen primer @ 0.40 ltrs/Sqm and there after laying of a layer of APP based polymeric membrane (five layered with centre core as 100 microns high molecular high density polyethylene film) weighing 3kg/Sqm and will be laid as per MES SSR Pt-I para 11.43.2.2 with minium side lap 75 mm and end Lap of 150 mm bonded with hot blown bitumen 85/25 gde penetration @ 1.20 kg/sqm and blinded with fine sand in dry condition (pleable free) @ 0.50 kg/sqm dusted over the bitumen coat complete all as specified and as directed by Engineer-in-Charge.

M&L for demolition of Brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and recast concrete articles complete all as specified and directed by Engr-in-charge.

M&L for taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc.complete all as specified and as directed by Engineer-in-Charge.

M&L for rendering 15 mm thick in cement mortor 1:4 on fair faces of brick work or concrete surfaces complete all as specified and directed by Engr-in-charge.

M&L for rendering 5 mm thick in cement mortor 1:3 on fair faces of brick work or concrete surfaces complete all as specified and directed by Engr-in-charge.

M&L for rendering 10 mm thick in cement mortor 1:6 other than fair faces of brick work or concrete surfaces complete all as specified and directed by Engr-in-charge.

M&L for complete removal of existing treatment, preparation of plastered surfaces of wall and applying two coats of cement base paint over one coat of cement primer including 1 mm thick exterior wall care putty ( to be applied in two coats) all as specified. Note: Putty surface shall be rubbed with emery paper to form even and smooth surface.

M&L for preparation of plastered surfaces of wall and applying two coats of cement base paint over one coat of cement primer new surfaces including 1 mm thick exterior wall care putty ( to be applied in two coats) complete all as specified and directed by Engr-in-charge. Note: Putty surface shall be rubbed with emery paper to form even and smooth surface.

M&L for complete removal of existing treatment,preparation of surfaces of old wall surfaces and applying two coats of oil bound distember over one coat of primer paint over and including 1mm thick wall care putty complete all as specified and as directed by Engineer-in-Charge.

M&L for two coats of oil bound distember over a coat of primer over two coats of approved wall care putty over and including preparation of new plastered surfaces of wall/ ceiling complete all as specified and as directed by Engineer-in-Charge.

M&L for taking down the shutter of any description exc 1 sqm but n.exc 2sqm each in samecomplete all as specified and as directed by Engineer-in-Charge.

M&L for taking down Chowkats or frames exc 1.5 Sqm but not exceeding 4 Sqm each (Without taking off shutters from the frames) complete all as specified and as directed by Engineer-in-Charge.

All as per SINO 41 above but area n.exc 1.5 sqm complete all as specified and directed.

S&F for second class hard wood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed complete all as specified and as directed by Engineer-in-Charge.

S&F 32mm thick flush shutter, solid core construction with black board and decorative prelam face panels ( as per sample kept in GE office) on both faces complete all as specified and directed.

S&F 35 mm Glazed and skeleton shutters, 2nd class H.W open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkatscomplete all as specified and as directed by Engineer-in-Charge.

S&F 125x 60 mm Pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete all as specified and directed by Engr-in-charge.

S&F 105x 60 mm Pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete all as specified and directed by Engr-in-charge.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm wall nut colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete, all as specified and directed by Engr in Charge.

S&F Factory Made Solid PVC Moulded Door Shutter wall nut colour, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the ront face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing but 2mm thick Moulded Prelam PVC Sheet on the front ace & 2mm Plain colour PVC Sheet on back face ®complete all as specified and as directed by Engineer-in-Charge.

S&F Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and directed by Engr-in-Charge

S&F mild steel 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed by Engr-in-Charge

S & F powder coated (of approved colour ) aluminium sections as in frame & shutter of windows (Hung/sliding), ventilators (louvers/fixed type) and fixed frame etc fixed to wall including rollers for sliding shutter and necessary locking arrangement, preparation of disturbed portion both side (internal & external surfaces of wall) match with existing surface treatment and all sides of aluminium frame shall be sealed with silicon sealent (inner/outer face) complete all as specified as directed by Engr-In-Charge.

S & F Stainless steel mosquito proof wire cloth of stainless 0.36mm dia and 1.4mm aperture fixed with aluminium flat/channel and screws all as specified as directed by Engr-In-Charge.

S & F glazing with 5.0 mm thick tinted/plain/frosted/glass exc 0.50 sqm in each panel fixed to aluminium section of windows/ventilator and fixed frame with suitable EPDM rubber packing and powder coated aluminium beading to frame complete all as specified and directed by Engr-in-charge.

M&L for dismantling timber scantlings of size and section in section, in any position as in truss or pulin etc.complete all as specified and directed by Engr-in-charge.

S & F Roof trusses (framed) , trussed , purline, cross gantries and fastening and heavy brakets framing (Beam, tee, angle,channel or flat section ) including guest olate, distance pieces Fe-410 gde (E-250) quality A complete all as specified and directed by Engr-in-charge.

M&L for mild steel framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted or gorged into spikes, framed guard bar, barred iron doors; ladder, framed balusters; railing; frame work for water tanks, cooler stand etc and similar work conforming to Fe 290 or Gde-E-165, complete all as specified and as directed.

S&F in repairs 0.80 mm Mild steel, plain, black sheet in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and ixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred fixed in position all as directed by Engr-in Charge.

M&L for preparation of old steel and iron surfaces exceeding 10cm width or girth and applying two coats of synthetic enamel paint over preprimed surfaces, complete all as specified and as directed by Engr-in-Charge.

M&L for Preparation of new steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primercomplete all as sp[ecified and directed.

M&L for two coat of enamel paint on wooden surfaces over a coal of pinkprimer incl preparation of new Surfaces of any description, not otherwise descri-bed, over 10cm width or girth complete all as specified and directed by Engr-in-charge.

All as per SI NO 61 above but one coat of synthetic enamel paint except primer on old surfacescomplete all as specified and as directed by Engineer-in-Charge.

S&F 300 mm Mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 16mm dia with and including a minimum of 6 bolts and nuts, four on olt plate and two on staple plate and fixed complete all as specified and as directed by Engineer-in-Charge.

S&F 150 mm Aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified and as directed by Engineer-in-Charge.

S&F 125 mm Extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed by Engr-in-charge.

S&F 100 mm Butt hinges, medium weight, cold rolled mild steel, and fixed complete all as specified and as directed by Engineer-in-Charge.

S&F Small fittings 1st class hard wood such as brackets of any type, latch and hinge blocks, shaped door and window stops and the like, including all necessary' labours; articles n exc 200 cu. cm each complete all as specified and directed.

S&F in reapirs 25 mm dia MS powder coated antique type curtain rods with bracket fixed to wall with suitable screws and onion type end brackets all as per approved design / colour/pattern fixed complete all as specified and directed by Engr-in-charge.

M&L for dismantling floor,hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed by Engineer-in-Charge.

M&L for Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement lurry and pointed in white or coloured cement to match including 10 mm screed bed 1:4 cement mortarcomplete all as specified and as directed by Engineer-in-Charge.

M&L for Non - skid Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed with spacer and laid with epoxy grout in neat cement slurry and pointed to match including 10 mm screed bed 1:4 cement mortarcomplete all as specified and as directed by Engineer-in-Charge.

M&L for glazed ceramic tiles 300x450x7 mm to 8mm thick in vertical surfaces such as skirting, dadao and risers to steps over 10 mm thick in CM(1:3) incl taking down from existing surfacescomplete all as specified and as directed by Engineer-in-Charge.

M&L for demolition of rerinforced cement concrete of any description and in any position complete all as specified and as directed by Engineer-in-Charge.

M&L for granite stone slab flooring 16 to 18 mm thick machine cut, rounding edges and polishing , bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing, over 20mm thick screed bed bedding in CM 1 :4 complete all as specified and as directed.

S & F looking mirror of size 450 x 600 using 5 mm thick mirror edges rounded fixed with clips all as specified incuding teak wood/pvc frame of size 25 x 25 mm decorativ and water proof including malimine polishingcomplete all as specified and as directed by Engineer-in-Charge.

S&F viterous china wash basin,white colour flat back size 550X440 mm incl waste coupling CP 32 mm dia chin and plug and porcelain stopper and CI brackets of iron 65x65x6mm embedded in PCC block with pcc 1:2:4 type B-1 and PVC waste pipe 32 mm dia & CP grating with holes with full pedestal of china ware,including PVC connection 15mm size with PTMT nuts of length 600mm and pillar mixer 'Hot and cold',fancy type,cast copper alloy, with capstan heads,choRmium plated,screwed down,high pressure,with or without lettered with long screwed shanks and fly nuts, screwed for iron pipe of bore 15mm,fixed in complete all as specified and as directed by Engr-in-Charge.

S&F 75 mm bore PVC (SWR) pipes single socketed , in any length with rubber ring joints, laid in trenches or in floorscomplete all as specified and as directed by Engineer-in-Charge.

S&F 110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls with MS clamps, all as specified and directed by the Engr-in-charge.

S&F PVC (SWR) bends 75 mm bore any radius with oveal & acces doorcomplete all as specified and as directed by Engineer-in-Charge.

S&F PVC (SWR) bends any radius in 110 mm diacomplete all as specified and as directed by Engineer-in-Charge.

S&F PVC (SWR) branch piece, single (single Y) equal or unequal complete all as specified and as directed by Engineer-in-Charge.

S&F PVC (SWR) floor trap plain/multi with grating incl. jointing with solvent cement (75 mm bore)complete all as specified and as directed by Engineer-in-Charge.

S&F in repairs sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mmcomplete all as specified and as directed by Engineer-in-Charge.

S & F in repairs made of stainless steel , 0.60 mm thick for kitchen plate rack , with plug , washers, fixing on wall, over all size 750x900 mmcomplete all as specified and as directed by Engineer-in-Charge.

M&L for machine cut kota stone slab flooring 18-20mm thick over 15 mm th cement screed in CM 1:4 base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishingcomplete all as specified and as directed by Engineer-in-Charge.

All as per SI NO 85 above but on vertical surfaces as risers incl M&L 5 mm thick screed in CM 1:3 complete all as specified and directed by Engr-in-Charge

M&L for marble strip cut to width n.exc 80 mm wide fixed as border in stair case walk ways etc.,over 25 mm thick cement screed in CM 1:3 base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete complete all as specified and directed by Engr-in-Charge

M&L for green marble 15mm to 17 mm thick (table rubbed and polishrd) in steps, jambs, pillars, window cills, cooking plateforms and like in cement mortor (1:4) including pointing in white cement (1:2)using marble dust with admixture of pigment to match with marble shade of green marbleincluding 15 mm th cement screed in CM (1:4) complete all as specified and directed by Engr-in-Charge

S&F reflective chequered vertical tiles 300x300x10mm size of approved colour and pattern set jointed over 10mm thick screed bed in CM 1:4 and pointed in neat cement slurry in floors complete all as specified and directed by Engr-in-Charge

M&L for Machine pressed precast conrete interlocking paver block with grey cement and pigment any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 grade complete all as specified and directed by Engr-in-charge.

M&L for sand filling in floors or pavings, laid in layers n.exc 15 cm thick,spread,levelled, and blinded with earth and rammed including watering complete all as specified and directed by Engr-in-charge.

M&L for demolition of un-reinforced cement concrete in roofs,floors ( other than ground floors), beams, staircase, landing, chajjas and similar suspended work.of and pavings not xceeding 15 cm thickness(below or above ground level)complete all as specified and as directed by Engineer-in-Charge.

M&L for demolition of cement concrete (unreinforced) in ground floor and in paving not exceeding 15 cm thickness (below or above ground level) complete all as specified.

M&L for 25mm thick cement concrete 1:2:4 type B-0 using 12.5mm graded crushed stone aggregates as in levelling course to receive floor rough finishes complete all as specified and directed by Engr-in-charge.

M&L for providing and laying water proofing treatment to sunken portion of WCs, bathrooms, etc by applying two coat of slurry of cement @ 0.488kg/Sqm mixed with acrylic based polymer modified cementitious composite compound @ 0.253kg/sqm this layer allowed to air cure for 4 hrs then applying slurry of cement @ 0.242 kg/sqm mixed with acrylic based polymer modified cementitious composite compound @ 0.126kg / sqm and allowed to aircure for 4 hrs and joints seal with sealing compound as approved by GE. Note: (i) Before laying of lime concrete joints of trap/WC/Soil pipes shall be properly sealed with sealing compound of Roofex/Forre/FOSROC and provn of P or S trap & Nahani /Floor traps with long aRm and also provn of spout of 40 mm dia complete all as specified and as directed by Engineer-in-Charge.

M&L for rendering 15mm thick on fair faces of brick work or concrete surfaces in Cement mortot as in CM 1:3 finishing even & smooth w/o using extra cement, complete all as specified and as directed by Engineer-in-Charge..

M&L for lean concrete using 40mm graded stone aggregate as in 1:5:10 as in filling sunken portion treatment, complete all as specified and as directed by Engineer-in-Charge.

S & F in repair Vitreous China Squatting pan "Orissa pattern" long pan, size 580 x 440 mm white ,with `P' or `S' trap, front or back inlet and foot rests any pattern including connection to trap and to flushing pipe, anti-syphonage pipe etc., including trap set in and including lime concrete complete all as specified and as directed by Engineer-in-Charge.

S & F in repairs PVC connections 15mm size with PTMT nuts of length 300mm complete all as specified and as directed by Engineer-in-Charge.

S&F in Repair PVC valveless , syphonic action type, Flushing cistern low level, white , with inlet, ball valve, float and handle including brackets,10 ltrs capacity including suitable pvc flushing bendcomplete all as specified and as directed by Engineer-in-Charge.

S & F in repairs Chromium plated shower roses with or without swivel joints, any size, including fixing to steel pipe or union complete all as specified and as directed by Engineer-in-Charge.

S & F angle cock concealed valve cast cpper alloy fancy type 15 mmcomplete all as specified and as directed by Engineer-in-Charge.

S & F in repair Bib tap cast copper alloy fancy type suitable for15 mm dia pipescomplete all as specified and as directed by Engineer-in-Charge.

S&F in repair Corner glass shelf complete all as specified and as directed by Engineer-in-Charge.

S & F CP towel rail 600 mm complete all as specified and as directed by Engineer-in-Charge.

S & F CP towel ring square complete all as specified and as directed by Engineer-in-Charge.

Taking up or down 15 mm bore steel tubing and connections, including cleaning for Refixing or removalcomplete all as specified and as directed by Engineer-in-Charge.

Taking up or down 25 mm bore steel tubing and connections, including cleaning for Refixing or removalcomplete all as specified and as directed by Engineer-in-Charge.

S & F 15 mm bore Galvanized Steel tubes, medium grade with all fittings for water supply pipes etc., laid in trenches/fixed on walls complete all as specified and as directed by Engineer-in-Charge.

S & F 25 mm bore Galvanized Steel tubes, medium grade with all fittings for water supply pipes etc., laid in trenches/fixed on wallscomplete all as specified and as directed by Engineer-in-Charge.

M&L for dismantling water tanks of exceeding 250 & not exceeding 500 ltrs and removing to store, complete all as specified and as directed.

M&L in repairs for 500 ltrs capacity Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top three layered) hoisted and fixed in position all as specified

S&F 20 mm Ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed in positioncomplete all as specified and as directed by Engineer-in-Charge.

M&L for GI Unions,20mm brass to connect iron to polyethylene and fixed complete all as specified and as directed by Engineer-in-Charge.

M&L for 50 mm thick plain cement concrete type C-1 1:3:6(Using 20mm graded crushed stone aggregates) as in plinth protection finished fair and even without using extra cement complete all as specified and directed. Note : The plinth protection shall be laid in panels and length of the each panel shall not be more than 2.00 metre all as directed. 6mm joints filled with 85/25 grade bitumen and sand (1:3 ratio) shall be provided. No deduction for joints shall be made while making payment against the above item complete all as specified and directed by Engr-in-Charge

M&L in repair 20 mm thick cement plaster on fair face of concrete surface including repair of doubing roof/chajja/facia surfaces in CM 1:3 finished even land smooth without using extra cement over complete all as specified and directed.(Water proofing compound shall be measured and paid seprately )

M&L for taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends swan necks, etc, including cleaning or refixing or removal to store (measured overall as fixed along the centre line over fitting and accessories). complete all as specified and as directed by Engineer-in-Charge.

M&L for dismantling boarding, any description, fixed in any position with nails complete all as specified and as directed by Engineer-in-Charge.

S&F 18/19 mm thick Prelaminated MDF board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with crews to timber frame work as in Cupboard, kitchen cabinet or similar work etc including provn of 6mm thick teak wood lipping alround the board/ shutter complete all as specified and as directed by Engineer-in-Charge.

S & F 30mm Continuous (piano) hinges, mild steel, bright finish or electro galvanised complete all as specified and as directed by Engineer-in-Charge.

S&F Aluminium handles, cast type, anodised 100mm longcomplete all as specified and as directed by Engineer-in-Charge.

S&F 100 size Hasp and staple, Alu Anodised, including bolt to hinge plate and fixed with screws complete all as specified and as directed by Engineer-in-Charge.

S&F magnet catchers 50mm steel plate MS body and striking plate incl letting in & fixedcomplete all as specified and as directed by Engineer-in-Charge.

M&L for extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using ex- tra cement, including foRms, moulds, mi- tred/stopped ends etc. complete all as specified and directed.

S&F in repairs stainless steel multipurpose basket in wooden drawers/partitions for storing rations of various types made of 3 to 4mm dia stainless steel rods, fixed in side partitions etc fixed, complete all as specified for modular kitchen complete all as specified and as directed by Engineer-in-Charge.

S&F in repair stainless steel zero crank hinges (auto) fancy type (with Euro concealed hinges) fixed to shutters in cupboards of standard size and shape for modular kitchen, complete all as directed by Engr-in-Charge for modular kitchen complete all as specified and as directed by Engineer-in-Charge.

S&F in repairs telescopic drawer side channel of std size and incl of roller for moving drawer, mild steel bright finish, or electrogalvanised, for modular kitchen, complete all as specified for modular kitchencomplete all as specified and as directed by Engineer-in-Charge.

M&L for demollition of stone slabs and tiles laid bedded and pointed in any mortar of any description or thickness in floors, aprons etccomplete all as specified and as directed by Engineer-in-Charge.

M&L for 75 mm thick plain cement concrete 1:4:8 type D-2 (using 40mm graded crushed stone aggregates) as in sub base complete all as specified and as directed by Engr-in-charge

Taking down carefully the existing Copper/Aluminium point wiring of any size and type by disconnecting from the either terminals complete with switches, sockets, ceiling rose, regulators, bell etc by unscrewing and removing materials to store for keeping in safe custody for re-use or for taking credit and making good to disturb surface of walls, floors etc., complete all as specified and directed by Engr -in- charge. Note : (i) Old dismanteled wiring and accessories (other than reuse) will be contractors property and credit will be charged against schedule of credit.

M&L for point wiring with PVC insulated unsheathed, FRLS 1100 volts grade stranded copper conductor cable single core 1.5 Sqmm for one light / fan point controlled by one way switch, and wire to be drawn in and including rigid pvc concealed conduit of dia not less tham 20mmof 2mm wall thickness complete with all accessories including GI anealed metal box 1.2 mm thick switch board of suitable size be fixed flush wall , with 3 mm thick ebonite sheet cover and necessary screws, cap washers etc. or to be fixed on wall respectively as directed by EIC and providing earth continuity wire using PVC insulated, un sheathed single core stranded copper conductor FRLS cable of size 1.5 Sqmm.

All as per item No.131 above but for bell / buzzer on independent board controlled by one push button bell switch.

All as per item No. 131 above but for one 5 Amps socket outlet on independent board.

All as per item No.131 above but wire size 2x2.5 Sqmm and and providing earth continuity wire using PVC insulated, unsheathed single core stranded copper conductor FRLS cable of size 2.5 Sqmm. to controlled the 3 pin 5 / 15 Amps socket outlet on independent board.

M&L for point wiring with 1.5 Sq. mm copper conductor, single core, PVC sheathed, cable, to controle one 3 pin socket outlet, 5 Amps on the same board with other switch complete all as specified and as directed by Engr-in-charge

S&F Switch Piano, flush type, One way, single pole, 5 Amps, suitable for 240 V, 50 Hz, AC supply complete all as directed by Engineer- in - Charge.

S&F two in one, 3 Pin, 5 Amps, flush type socket outlet complete all as directed by Engineer- in - Charge.

S&F switch Piano, flush type, One way, single pole, 15 Amps, suitable for 240 V, 50 Hz, AC supply complete all as directed by Engineer- in - Charge.

S&F two in one, 3 Pin, 5/15 Amps, flush type socket outlet suitable for 240 V, 50 Hz, AC supply complete all as directed by Engineer- in - Charge.

S&F push bell switch piano, flush type, white colour, single pole, 5 Amps, suitable for 240 V, 50 Hz, AC supply complete all as directed by Engineer- in - Charge.

S&F ceiling rose, 3 terminal, PVC / polycarbonet, isolated body complete all as directed by Engineer - in - Charge.

S&F stepped type, electronic fan regulator, flush type on the existing phenolic laminated sheet etc. as required complete all as directed by Engineer- in - Charge.

S&F calling bell, suitable for 230 Volt, 50 Hz, single pole, AC supply complete all as directed by Engineer- in - Charge.

S&F Slim linear LED lighting fixture 18 watt LED batten, with full base of extruded aluminium section acting as a heat sink with closed back, isolated driver, complete making all connection using 1.5 sqmm copper conductor multistrandard PVC insulated 2 core flexible cable with flexible PVC pipe from ceiling rose to fittings complete including taking down old US tube light fitting 36/40W and taken in schedule of credit all as per the direction of Engr-in-Charge.

S&F of decorative ultra slim linear LED lighting fixture 10/12 watt LED complete making all connection using 1.5 sqmm copper conductor multistranded PVC insulated 2 core flexible cable from ceiling rose to fitting by using extra length flexible cable 2 core other than provided by manufacture complete all as per directed by Engr-in-charge

S&Fof decorative ultra slim linear LED lighting fixture 5/6 watt LED complete making all connection using 1.5 sqmm copper conductor multistranded PVC insulated 2 core flexible cable from ceiling rose to fitting drawn through in PVC flexible conduit complete all as per directed by Engr-in-charge

S&F security (street) light fitting 35 watt, new generation energy saving & environmental friendly long life versatile pressure die cost aluminium IP 66 with acylic, powder coated, pressure die cast aluminium compact high power LED street light with heat resistant toughed glass, corrosion resistant, isolated driver, including provision of GI tubing bracket of suitable size and fixed on wall including clamps, nut, bolts and washer for fixing of security (street) light completet including taking down old US light fitting of any type /size and taken in schedule of creditall as per direction of Engr-in-Charge. Make:SYSKA Cat no SSK-ST-25W(S) or equivalent in Havells Cat No : ENDURACITYLITEPLATPLUSSL35WLED757SASYBOPC,

S&F new generation energy saving LED bulk head 9/10 Watt with opal diffuser suitable for 600 LUMEN complete all as specified and as directed by Engr-in-charge

M&L for taking down old unserviceable MCB DB with MCB etc after disconnecting for re use or for credit complete all as specified and as directed by Engineer-in-Charge.

M&L for taking down fan/Exhaust fan, ceiling cable end, dismantling blades and kept in safe custody for repairing/servising all as specified and directed by Engineer-in-Charge.

M&L for repair of ceiling fan 1200mm sweep/ Exhaust fan of any make obtained from above item, oiling, greasing after cleaning slot, over hauling & replacement of defective split pin nut bolts washer etc including spray painting with enammeled paint with the help of spray gun and marking of MES No with black enammeled paint all as specified and directed by Engr-in-charge.

M&L for hanging /fixing only ceiling/Exhaust fan and connecting up including provision of stranded 3core flexible 1.0sqmm copper conductor cable from ceiling rose or connector to fan all as specified and directed by Engr-in-charge.

M&L for earthing complete with GI earth plate electrode 600mmx600mmx6mm thick burried in ground vertically to a depth not less than 2.25meters below ground level with top edge of the earth plate at a depth not lesss than 1.5 meter below Normal ground level, earth plate surrounded 15cm thick layers of common salt and charcoal dust starting from ground below 15 cm of earth plate and up to 15 cm above the same. GI plate connected with galvanised earth lead wire 4.0mm dia by means of GI nuts, bolts and washers of galvanised iron or steel all as shown in electrical plate no.5 connecting to earth test point all as specified or indicated including testing on complition with following:- (a) Test point GI wire 4mm dia . (b) Watering pipe GI light grade 20mm dia from top of the earth electrode up to MS funnel with wire mesh embeded in floor of PCC earth pit. (GI Funnel should properly tightned on GI watering pipe and embeded in PCC floor of earth pit with open top suitable for watering of earth pits) (c) PCC earth pit 30x30x30cm constructed in PCC 1:2:4 type B1 exposed surfaces smoothly finished with 15mm thick cement mortar 1:6 plaster including RCC pit cover 25mm thick with 2 Nos MS handles of 12mm dia suitable for carrying of pit cover. (d) Angle iron frame made of 40x40x4 mm angle iron for 30x30 mm PCC pit for holding the pit cover.

M&L for earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc. as required 6sqmm galvanised iron or steel wire all as specified and directed by Engr-in-charge.

S & F sheet metal VTPN DBs - 160 Amp bouble door 04 way (optimum F2+12) with metal door 415 volts grade IP 43 Protection Grade fixed flush to wall complete including connections should be provide with necessary reducer lugs all as specified and directed by Engr-in-charge.

S&F in repair MCB TPN 63 to 100Amps, 240 Volts all as specified and directed by Engr-in-charge.

S&F MCCB adjustable type, 100 Amps with breaking capacity 36 KA , 4 pole, 415V all as specified and directed by Engr-in-charge.

S & F in replacement single pole and neutral sheet steel powder coated Distribution board for MCBs fitted with bus bar , Neutral link ,Earth Bar and Din rail suitable for use on 240 V, 50 Hz supply double door SPN DB system 8 ways.all as specified and directed by Engr-in-charge.

S&F connection and testing MCB SP 40 Amps 'C' Curve all as specified and directed by Engr-in-charge.

S&F on load change over switch 02 pole 240 V AC, 50 Hz in sheet metal enclosure SPN of capacity 63 Amp all as specified and directed by Engineer-in-Charge

S&F 'C' series SPN MCB 40 Amps 240V ,50Hz,10kA lighting and other domestic loads incl all termnials, fitting etc.all as specified and directed by Engr-in-charge.

S&F 'C' series SPN MCB 40 to 63 Amp Amps 240V ,50Hz,10kA lighting and other domestic loads incl all termnials, fitting etc.all as specified and directed by Engr-in-charge.

S&F connection and testing MCB SP 6-32 Amps 'C' Curve all as specified and directed by Engr-in-charge.

S&F connection and testing MCB SP 6-32 Amps 'B' Curve all as specified and directed by Engr-in-charge.

M&L for taking down serviceable/ unserviceable electric meter including meter box from existing position carefully for refixing including making good to disturbed surfaces all as specified and directed by Engr-in-charge. (Note : Disturbed surfaces should making good by Plastering/ distembering/colour washing / white washing to match with existing surfaces)

Re fixing of serviceable electric meter obtained from item No 170 with meter box by scouting to the wall and fix firmely all as specified and directed by Engr-in-charge.

SupplyIing, laying / fixing and testing in replacement XLPE Insulated screened PVC bedded, galvanized steel strip or wire armored, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 25 sq mm 2 core in trenches/floor/pole/GI pipe complete including cutting/chasing to any surface and making good to the disturbed surface to match the existing all as specified and directed by Engr-in-charge.

M&L for dry sand cushioning to under ground cables provided with a layer of sand 8 cm deep before laying the cable, 15 cm depth after laying cable & stretching the cable all as specified and directed.

Supply and lay brick class ‘B’ covering as mechanical protection to cable with well burnt all as specified and directed by Engr-in-charge.

M&L for GI tubing light grade with all fitting and fixed in wall and floor or fixed to pole of size 40mm dia.all as specified and directed by Engr-in-charge.

M&L for bore hole for passing of cable through/insection of 40/80 mm dia GI pipe under PCC/Road/Taxy Track/ Runway/ Hard standing not less than 1200 mm deep complete all as directed Note: (i) Cost of equipments, tools and plants, material required for boaring shell be deemed to be included in unit quoted rate above. (ii) Cost of GI pipe 50/80 mm dia shell be deemed to be included in unit quoted rate above. (iii) Cost of air compressor for boaring shell be deemed to be included in unit quoted rate above.

M&L for sub main wiring with two single core 6sqmm standed copper conductor PVC insulated and unsheated cable ISI marked 25mm dia ,medium grade PVC conduit concealed in wall for sub main connection including 6Sqmm PVC insulated unsheated copper conductor ISI marked as earth wire complete all as specified and directed by Engr-in-charge.

sohtra and co

M/S GURBACHAN SINGH

SATYA SALES AND BUILDERS

M/S IMTESH BHAT

HANS RAJ SHARMA

MADAN LAL SHARMA AND SONS

SHIVAE CONSTRUCTION

paras ram pachiala