Construction of Munsiff Court Complex at Billawar

Amount

Earthwork in excavation by mechanical means (Hydraulic excavator) over areas (Exceeding 30cm and upto 1.5m in depth, 1.5m in width as well as 10sqm on plan) including disposal of excavated as directed by the Engineer-in-charge including all lead, lift and carriage complete. a) All kind of soils

Earthwork in excavation by manual means in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5m width) and for shafts, wells, cesspits and the like not exceeding 10sqm on plan, depth upto 1.5mtr. including disposal of excavated earth as directed by the Engineer-in-charge including all lead, lift and carriage complete. a) All kind of soil.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering all work up to plinth level in (including all leads and lifts carriages of material by MT/HL)

1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate) 40mm nominal size crushed.

1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate) 40mm nominal size crushed.

1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate) 20mm nominal size crushed.

Providing and laying in position of reinforced cement concrete 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20mm nominal size) excluding the cost of centering, shuttering, finishing and reinforcement. All work upto plinth level. (including all leads and lifts carriages of material by MT/HL)

Providing and laying DPC 50mm thick in 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size crusher aggregate) (including all leads and lifts carriages of material by MT/HL)

Applying a coat of residual petroleum bitumen of Grade VG-10 of approved quality using 1.7 kg per square metre on damp-proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil.

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. upto floor five level excluding cost of centring, shuttering, finishing and reinforcement. 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded crushed stone aggregate 20mm nominal size) (including all leads and lifts carriages of material by MT/HL)

Brick work with common burnt clay F.P.S (non modular) bricks of class designation 75 in foundation plinth in cement mortar 1:6 (1 cement : 6 coarse sand) (including all leads and lifts carriages of material by MT/HL)

Brick work with common burnt clay F.P.S (non modular) bricks of class designation 75 in foundation plinth in cement mortar 1:4 (1 cement : 4 coare sand) (including all leads and lifts carriages of material by MT/HL)

Extra for brick work in superstructure above plinth level upto floor V level. (By manual means) (including all leads and lifts carriages of material by MT/HL)

Half brick masonry with bricks of class designation 75 in foundations and plinth in Cement mortar 1:4 (1 cement: 4 coarse sand) (including all leads and lifts carriages of material by MT/HL)

Extra for Half-brick masonary in superstructure above plinth level upto floor V level (including all leads and lifts carriages of material by MT/HL)

Providing and laying Reinforced cement concrete 1:1.5:3(1 Cement: 1.5 Coarse Sand: 3 graded crushed stone aggregate 20 mm nominal size) in suspended floors, balconies, landings and staircases having upto 15° slope excluding the cost of centering & shuttering. All works upto Floor V level. a) 1: 1.5: 3 (1 Cement: 1.5 Coarse Sand: 3 graded crushed stone aggregate 20 mm nominal size) (including all leads and lifts carriages of material by MT/HL)

Reinforcement for RCC work including straightening, cutting, bending, placing in position and binding all complete. a) Cold twisted bars.

Centering and shuttering including strutting, propping etc. and removal of form work for:-

Foundations, footing, bases of columns etc for mass concrete.

Suspended floors, roofs landings balconies and access plate form.

Columns, pillars,piers, abutments,posts & struts.

Edges of slab and breaks in floors and walls under 20cm wide.

Lintels, beams, plinth beams girders, bressumers and cantilevers.

Stair (Excl.landings)except spiral staircases.

Weather shade, chajjas, corbels etc. incl.edges.

Extra for additional height in centring, shuttering where ever required with adequate bracing, propping etc. including cost of de-shuttering and decentring at all levels, over a height of 3.5m, for every additional height of 1 metre or part thereof (Plan area to be measured). a) Suspended floors, roofs, landing, beams and balconies (Plan area to be measured).

Filling available excavated earthwork (excluding rocks) in trenches , plinth, sides of foundation etc. in layer not exceeding 20 cm in depth : consolidating each layer by ramming and watering , lead upto 50 mts, lift 15 mts).

Supplying and filling in plinth with fine sand under floors including, watering, ramming consolidating and dressing complete (including all leads and lifts carriages of material by MT/HL)

6mm cement plaster to ceiling of mix 1: 3 (1 Cement:3 Fine sand) (including all leads and lifts carriages of material by MT/HL)

15 mm cement plaster on rough side of single or half brick walls of mix 1: 6 (1 cement: 6 fine sand) (including all leads and lifts carriages of material by MT/HL)

12mm cement plaster on brick wall of mix 1 : 6 ( 1 cement : 6 fine sand) (including all leads and lifts carriages of material by MT/HL)

15 mm cement plaster on rough side of single or half brick walls of mix 1: 4 (1 cement: 4 coarse sand) (including all leads and lifts carriages of material by MT/HL)

12mm cement plaster of mix 1 : 4 ( 1 cement : 4 coarse sand) (including all leads and lifts carriages of material by MT/HL)

15mm cement plaster 1:3 (1 cement:3 coarse sand) finished with a floating coat of neat cement on the rough side of single or half brick wall (including all leads and lifts carriages of material by MT/HL)

Add or deduct for plaster drip coarse / groove in plastered surface of moulding to RCC projections.

Making of grove 12mm x 10mm between brick and RCC

Providing 10cm / 7cm thick and 5 cm / 5.7cm projected string course with bricks of class designation 75 in cement mortar 1:4 (1 cement : 4 coarse sand) (including all leads and lifts carriages of material by MT/HL)

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z. sections and other sections of approved make conforming to IS : 733 and IS : 1285, fixed with rawl plugs and screws or with fixing clips, or with expansion hold fastners including necessary filling up of gaps at junctions at top, bottom and sides with required PVC / neoprene felt etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge (glazing and panelling to be paid for separately). a) For fixed portion using Powder coated aluminium (minimum thickness of powder coated 50 microns).

For shutters of doors, windows and ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately). a) Powder coated aluminium (minimum thickness of powder coated 50 microns).

Providing and fixing glazing in aluminium door, window, ventilator shutters and partition etc. with PVC / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer-in-charge. (Cost of aluminium snap beading shall be paid in basic item). With glass panes of 5.50 mm thickness (weight not less than 13.75 kg/sqm).

Providing and fixing 12mm thick prelaminated three layer medium density (exterior grade) particle board Grade-I, Type-II conforming to IS : 12823 bonded with phenol formaldehyde synthetic resin, of approved brand and manufacture in panelling fixed in aluminium doors, windows shutters and partition frames with C.P brass / stainless screws etc. compete as per architectural drawings and directions of Engineer-in-charge. Pre-laminated particle board with decorative lamination on both sides.

Providing and fixing double action hydraulic floor spring of approved brand and manufacture IS:6315 marked, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg for doors including cost of cutting floor, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge. a) With brass cover plate minimum 1.25mm thickness.

Providing and fixing Fly proof stainless steel grade 304 wire gauge with 0.5mm dia wire and 1.4mm wide aperture in aluminum door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge. (Cost of aluminum snap beading shall be paid in basic item).

Filling the gap in between aluminum frame and adjacent RCC/Brick/stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge. a) Upto 5mm depth and 5mm width.

Providing and fixing anodized aluminium grill (anodized transparent or dyed to required shade according to IS1868 minimum anodic coating of Grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing windows frame with C.P. brass / stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodized aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in-charge. (only weight of grill to be measured for payment).

Providing and fixing 12mm thick frameless toughened glass door shutter of approved brand and manufacture including providing and fixing top and bottom pivot and spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge (door handle, lock and stopper etc. to be paid separately).

Providing and fixing 100mm brass locks (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete.

Providing and fixing of aluminium sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS 1868) transparent or dyed to required colour or shade with nuts and screws complete

Providing and fixing of aluminum hanging floor door stopper ISI Marked anodized (anodic coating not less than grade AC 10 as per IS 1868) transparent or dyed to required colour or shade with nuts and screws complete Single rubber stopper.

Providing and fixing of aluminum casement stays ISI marked anodised (anodic coating not less than grade AC 10 as per IS 1868) transparent or dyed to required colour or shade with nuts and screws complete :

Providing and fixing aluminium handles ISI marked anodized (anodic coating not less than grade AC 10 as per IS:1868) transparent or dyed to required colour and shade with necessary screws etc. complete

Providing and fixing aluminum tower bolts ISI marked (anodized anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete

(ii) 200 x 10mm

(iii) 150 x 10mm

Kota stone slab flooring over 20mm (avg.) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete with base of cement mortar 1:4 (1 cement : 4 coarse sand) 25mm thick. (including all leads and lifts carriages of material by MT/HL)

Kota stone slab 25mm thick in riser of steps, skirting, dado and pillars laid on 12mm (average) thick cement mortar 1:3 (1 cement : 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete. (including all leads and lifts carriages of material by MT/HL)

Providing and laying 18mm thick Granite of any colour and shape (area of slab upto 0.5 Sqm) gang saw cut mirror polished (pre moulded and pre polished), machine cut for kitchen platform, vanity counters window sills facias and similar locations of required size of approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand) with joints treated treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing moulding and polishing to edge to give high gloss finish etc. complete at all levels(including all leads and lifts carriages of material by MT/HL)

Extra for providing edge moulding to 18mm thick Granite stone counters, Vanities etc. over item No. 8.2 including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-charge.

Extra for nosing in steps and tread of kota stone slab.

Providing and laying / fixing ceramic glazed floor tiles 300 x 300mm (thickness to be specified by the manufactures) of first quality conforming to IS : 13755 of NITCO, ORIENT, SOMANY, KAJARIA or equivalent make in colour such as white, Ivory, Grey Fume Red, Brown laid on 20mm thick bed of cement mortar 1:4 ( 1 cement : 4 coarse sand) including pointing the joints with white cement and matching pigment etc. complete (including all leads and lifts carriages of material by MT/HL)

Providing and fixing 1st quality ceramic glazed tiles conforming to IS : 13753 of minimum thickness 5mm of approved make like NITCO, ORIENT, SOMANY, KAJARIA or equivalent make in all colour, shades except begundy bottle green, black or any size as approved by Engineer- in-Charge in skirting, risers of steps and dados over 12mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.30 kg per sqm including pointing in white cement mixed with pigment of matching shade complete (including all leads and lifts carriages of material by MT/HL)

Providing and laying vitrified premium quality floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622 of approved make of Kajaria / Somany Brand S&P Brown /Grey in colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) including grouting the joints with matching Epoxy etc. complete (size of tile 60x60cm) as per direction of Engineer-in-charge (including all leads and lifts carriages of material by MT/HL)

Providing and laying anti skid full-body vitrified premium quality floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622 of approved make of Kajaria / Somany Brand S&P Brown /Grey in colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) including grouting the joints with matching Epoxy etc. complete (size of tile 30x30cm) as per direction of Engineer-in-charge (including all leads and lifts carriages of material by MT/HL)

Chequerred precast cement concrete tiles 22mm thick in footpath and courtyard jointed with neat cement slurry mixed with pigment to match the shade of the tiles, including rubbing and cleaning etc. complete on 20mm thick bed of cement mortar 1:4 ( 1 cement : 4 coarse sand). Medium shade using 50% white cement and 50% ordinary cement (including all leads and lifts carriages of material by MT/HL)

Extra for providing opening of required size and shape for wash basins/kitchen sink in kitchen platform, vanity counters and similar location in marble / stone work including necessary holes for pillar taps etc. including rubbing and polishing of cut edges etc. complete.

Providing and laying integral cement based water proofing treatment including preparation of surfaces as required for treatment of roofs, balconies, terraces etc. (Make Armocreate of SWC Chryso France) consisting of (a) applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300mm height including cleaning the surface before treatment. (b) Laying brick bats with mortar using broken bricks / brick bats 25mm to 115mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20mm thick layer of cement mortar of mix 1:5 admixed with water proofing compound conforming to IS 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining was upto 300mm height including rounding of junction of walls and slaps. (c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg / sqm of cement admixed with water proofing compound conforming to IS 2645 and approved by Engineer-in-charge. (iv) Finishing the surface with 20mm thick joint less cement mortar of mix 1: 4 admixed with water proofing compound conforming to IS 2645 and approved by Engineer-in-charge including laying glass fiber cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300mm / sq 3mm deep. (e) The whole terrace so finished shall be flooded with water far a minimum period of two weeks for curing and for final test. All above operations to be done in order and as directed and specified by Engineer-in-charge. With average thickness of 120mm and minimum thickness at khurras as 65mm (including all leads and lifts carriages of material by MT/HL)

Providing and fixing on wall face unplasticised-Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10mm gap for thermal expansion. Single socketed pipes of 110mm diameter.

Providing and fixing on wall face unplasticised-PVC moulded fitting / accessories for unplasticised- rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10mm gap for thermal expansion :-

Coupler 110mm

Single tee with door 110x110x110mm

Bend 87.5x110mm

Providing and applying white cement based putty of average thickness 1mm, of approved brand and manufacture, over the plastered wall surface to prepare the surface even and smooth complete.

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade new work (two or more coats) over and including priming coat with cement primer.

Finishing walls with acrylic smooth exterior paint of required shade on New work (two or more coats applied @ 1.67 litre/10 sqm. over and including base coat of water proofing cement paint applied @ 2.20 kg/10 sqm.

Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes channels, plates etc. including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete including fixing the railing with necessary accessories and stainless steel dash fasteners, stainless steel bolts etc. of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Providing and fixing nickel plated M.S. pipe curtain rods with nickel plated brackets. 25mm dia (heavy type).

Making plinth protection 50mm thick cement concrete 1:3:6 (1 cement : 3 course sand : 6 graded stone aggregate 20mm nominal size) over 75mm bed of dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth crushed (including all leads and lifts carriages of material by MT/HL)

Brick edging 7 cm wide 11.4cm deep to plinth protection with bricks of class designation 75mm including grouting with cement mortar 1:4 (1 cement : 4 fine sand) (including all leads and lifts carriages of material by MT/HL)

Lettering with black Japan paint of approved brand and manufacture.

a) 10cm height.

b) 20cm height.

Providing and fixing water closet squatting pan (Indian Type W.C Pan) with 100mm sand cost iron P or S trap, 10 ltrs low lewel PVC flushing cistern including flush pipe (Hindware make Cat No. 20070/ Kerovit make Cat No. 606) Manually controlled device (Handle lever) conforming to IS : 7231, with all fitting and fixture complete including cutting and making good the wall and floows wherever required. Orissa Pan white viterous china pan of size 580x440mm with integral type footrests.

Applying one coat of water thinable cement primer of approved brand and manufacture on wall surface. a) Water thinable cement primer.

Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade. Two or more coats on new work.

Finishing walls with textured exterior paint of required shade on New work (two or more coats applied @ 3.28 litre / 10 sqm over and including base coat of water proofing cement paint applied @ 2.20 kg / 10 sqm.).

Providing & fixing of white vitreous China pedestial type water closet (European Type) with cistern (A/PHAS-100 Cat No. 201100+Cat No. 21054 / Kerovit model No. 112 and flush tank model no. 1001) with CP bolts, nuts, CI chair hanging arrangements, bakelite seat & cover with CP hinges & rubber buffers, CP brass screw, washer with all accessories with WC connector with Rubber Lip / Buffer and side gap filled with silicon sealant wherever required. Including brass / SS screws and washer complete including cutting, making good the walls, floors, slab wherever required as per direction of Engineer-in-charge.(including all leads and lifts carriages of material by MT/HL)

Providing & fixing of white vitreous china under counter oval wash basin/circular basin (Hindware 10080 / Kerovit model No. 206 & 207) with CP brass waste assembly, CP cast brass bottle trap with extension piece (Jaquar Cat No. 769B + Parko1535 or approved equivalent), 450mm long CP copper connections pipes (Jaquar Cat No. 803B or Parko 1535 or approved equivalent), wall flanges and rubber adapters for waste connection complete including CI/MS brackets duly painted, nuts, washers, cutting and making good the walls floors wherever required as per direction of Engineer-Incharge.

Providing & fixing of white vitreous china wash basin with pedestal (Hindware Cat No. 1008 + Ped Cat No. 11003 / Kerovit model No. 234 Ped Model no. 305) with CP brass waste assembly, CP cast brass bottle trap with extension piece (Jaquar Cat No. 769B + Parko1535 or approved equivalent), 450mm long CP copper connections pipes (Jaquar Cat No. 803B or Parko 1535 or approved equivalent), wall flanges and rubber adapters for waste connection complete including CI/MS brackets duly painted, nuts, washers, cutting and making good the walls floors wherever required as per direction of Engineer-Incharge.

Providing and fixing of C.P. brass Central Hole Basin Mixer without Popup Waste System including with 450mm Long Copper Pipes & Brass Nuts with all fittings and accessories as per direction of Engineer-Incharge. (Jaquar CQT 23167 D / Kerovit make Cat No. 1511010-ND-CP).

Providing & fixing white vitreous china flat back urinal with automatic flushing systems (Hindware 60021 / Kerovit model No. 505) comprising of all plumbing, electronic and electrical items. CP brass flush pipe with CP brass elbow, CP brass spreader, CP wall flange, infrared photo cells, eyes electrically operated solenoid valve, step down transformer / equipment and any other item required to provide satisfactory functioning including necessary wall cutting / chasing and making good, as required for urinal flushing complete as mentioned above as per direction of Engineer-in-charge.

Providing & fixing C.P. hand spray with lever control (health faucet) (Jaquar Cat. No. ALDCHR-565 / Kerovit make KA580001) and flexible hose 1 m long connection with C.P. holder for hand spray complete in all respects as per direction of Engineer-Incharge.

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 a) 15 mm nominal bore (Make Jaquar CQT 23059 / Kerovit make Cat No. KB 1511003).

Providing & fixing C.P. brass robe hook (Jaquar Cat No. ACN 1191N) or approved equivalent) fixed to wall/door with plastic rawl plugs and C.P brass screws including cutting and making good the walls wherever required as per direction of Engineer-Incharge.

Providing & fixing recessed liquid soap dispenser (Jaquar Cat No. ACN 1135N) as per direction of Engineer-Incharge.

P/F of Soap Dish Holder with all fittings as per direction of Engineer-in-charge (Jaquar Cat No. ACN 113 N).

P/F brass towel ring round with round flenge of approved make complete with all fittings (Jaquar Cat No. CAN 11021 BN / Kerovit make Cat No. KA 930004).

P/F of glass shelf 600mm long with all C.P fittings of approved quality complete item (Jaquar Cat No., CAN 11071 N).

P/F of regular body concealed stop cock suitable for 15mm pipe line with protection cap (Jaquar Cat No. ALD 083 / Kerovit make Cat No. KB 111030 CP and exposed part Cat No. KB 1511032) with exposed part angular stop cock with flange FUS 29.53.

P/F PVC connection (Complete item).

Providing and fixing complete set of sanitary fixtures for handicapped toilets, Hindware Cat. no. 70002) comprising of EWC - P , Cistern, Seat Cover, Twin Flush Fittings, Wash Basin 450x300, Half pedestal, 1 faucet with spatula lever, 1 hinged rail and 2 grab bars, including cutting and making good the walls and floors wherever required complete as per directions of Engineer in charge.

Providing and fixing 6mm copper backed float glass mirror MODI / SAINT-GOBAIN including 6mm thick BWR type ply board, 40mm stainless steel channel plugged to wall, hard wood treated with two coats of wood preservative, etc. all complete as specified and shown in drawing complete to the satisfaction of Engineer in charge.

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS 13983 with C.I. brackets and stainless steel plug 40 mm including painting of fittings and brackets, cutting and making good the walls wherever required: Kitchen sink without drain board 610 x 460 mm bowl depth 200 mm (Pantry)

Providing and fixing 600x450mm beveled edge mirror of superior glass (of approved quality) complete with 6mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washer complete.

Providing and fixing, testing and commissioning of C.P. brass single hole sink mixer with CP wall flange, swinging spout complete as required and making good as per direction of Engineer-in-Charge (Jaquar Cat No. CQT-23167D)

Providing and fixing CP brass towel rail of approved make complete with CP brackets fixed to wooden cleats with CP brass screws. (Jaquar Cat No. ACN1111DNM / Kerovit make Cat No. KA 930001).

Providing and fixing 15 mm dia. C.P. brass bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. (Short Body) (Make Jaquar Cat No. CQT-23047)

Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms. (15 mm dia.) (Make Jaquar Cat No. CON-107KN / Kerovit make Cat No. KB 1511004 CP)

Providing at site of works and lowering, laying and jointing HDPE pipes and required specials of outer diameters conforming to IS : 14333-1996 and bearing ISI mark in prepared trenches to required grade and level icluding cost of jointing materials, chemicals, labour required for handling and making joints etc. including hydraulic testing of pipes, refilling of trenches etc. complete note :- Water for initial testing will be made available free by MIDC if possible. For subsequent fills necessitated on account of rectifications water will be charged at the prevailing industrial water rates in respective industrial area. (Make Supreme)

110 mm dia 6 Kg/cm2

160 mm dia 6 Kg/cm2

200 mm dia 6 Kg/cm2

Providing and fixing UV stabilized PVC rain water pipes conforming to IS:4985 (working pressure 6 kg/sqcm.) including jointing with seal ring conforming to IS:5382 leaving 10 mm gap for thermal expansion. (Make Supreme)

75 mm dia 6 Kg/cm2

110 mm dia 6 Kg/cm2

Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC rain water pipes conforming to IS 13592 Type A, including jointing with seal ring conforming to IS: 5382, leaving 10 mm gap for thermal expansion (Make Supreme)

Single tee with door 110 x 110 x 110 mm

Single tee with door 110 x 110 x 110 mm

Single tee with door 75 x 75 x 75 mm

Single tee with door 75 x 75 x 75 mm

Single tee reducer 110 x 110 x 110 mm

Bend 110 mm

Bend 75 mm

Door tee 110 mm

Door tee 75 mm

Reducer 110 x 75 mm

Construction brick measonery man hole in cement motor 1:4 (1 cement: 4 Coarse Sand) R.C.C top slab with 1:2:4 mix (1 cement: 2 Coarse Sand: 4 graded stone aggrigate 20 mm nominal size) foundation concrete aggrigate 40 mm Nominal Size, in side palstering 12mm thick with cement mortor 1:3 (1 cement:3 Coarse sand) finshed with floating coat near cement and making channels in cement concrete 1:2:4 (1 cement:2 Coarse snad:4 graded stone aggirgate 20mm nominal size) finished with floating coat of neat cement complete as per standard design. inside size 90cmx80cm and 45cm deep including cast iron cover with frame (light duty) 455x610mm internal dimensionals. total wt. of cover and frame to be not less than 38kg (wt. of cover 33kg and wt.of frame 15kg) with F.P.S bricks of class designation 75 (crush stone aggrigate) (including all leads and lifts carriages of material by MT/HL)

Constructing masonry Chamber 60 x 60 x 75 cm, inside with 75 class designation brick work in cement mortar 1:4 (1 cement : 4 fine sand) for sluice valve, with C.I. surface box 100mm top diameter, 160 mm bottom diameter and 180 mm deep (inside) with chain lid and RCC top slab 1:2:4 mix (1 cement :2 coarse sand : 4 graded stone aggregate 20mm nominal size) necessary excavation foundation concrete 1:5:10 (1cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard design. (With F.P.S. bricks) (including all leads and lifts carriages of material by MT/HL)

Providing and fixing Heavy class SS grating with Cockroach proof SS strainer of approved design including floor trap & setting in floor with cement motor to match with floor finish as per direction of Engineer-Incharge. (Size 100 mm dia) (ISI Marked)

Providing and fixing heavy class SS grating plane floor trap & setting in floor with cement motor to match with floor finish as per direction of Engineer-Incharge (Size 100 mm dia) (ISI Marked)

Providing and fixing of Tumbler holder with all fittings as per direction of Engineer-in-charge (Make Jaquar Cat No.CAN 114N).

Providing and fixing on wall mixed with provision for over head shower with 115mm long bend pipe on upper side connecting leg and wall flenges of approved quality with all fittings (Make Jaquar Cat No.SHA-479L).

Supply, installing, testing of approved make PE-AL-PE pipe manufactured a per IAPMO-IGC-INDIA 308, 2014 should have UMC marking each meter with continues blue line on the pipe. PE resin shall be as per ISO 4427-1, Aluminium as per IS-737 with minimum elongation of 18% and ultimate tensile strength of 85 Mpa with test certificate and including all relevant DZE bras fitting as female elbows / Tees, MTC, FTC and engineering plastic fittings with internal sealing system like Eq Elbows, Eq. tees, reduces, St couplers, clamps at one meter spacing, with PAP valves and brass tank nipples etc including testing of lines and joint as per engineer in charge make Kitec, Mainthilee and Vista (Hot & Cold) Internal work-Exposed on wall.

2025 (20mm OD) pipe.

2532 (25mm OD) pipe.

Concealed inside the walls.

1620 (20mm OD) pipe.

2025 (25mm OD) pipe.

External works

2025 (25mm OD) pipe.

2532 (32mm OD) pipe.

Providing and fixing U clamp with slotted base made of stainless steel AlSi 304 18/8, Makes Intello TEC

25mm U clamp

32mm U clamp

100mm U clamp

Slooted base 30x3mm (width x thicknes)500mm(Length)

Slooted base 30x3mm (width x thicknes)200mm(Length)

Slooted base 30x3mm (width x thicknes)300mm(Length)

Providing and fixing Polyproplene manholes with multiple inletand single outlet including excavation, fixing etc. complete in all respect upto 1.00 mtrs. deep (United make) Manhole 160mm.

Providing and fixing polypropylene soakaway Rings with tongue and groove joints designed to accommodate modular vertical expansion, single inlet and single outlet including excavation, fixing wrapping of the ring with geo-textile cloth etc. complete in all respect (United Make), Soakaway Rings 1.2m x 0.75mx0.5m (Soakage pit).

Supply, installing, testing of approved make Back water valves (NRV) for preventing of incoming water, reptile, rats and insect in the building premises through sewer lines at inspection chambers as per Engineer-in-charge Make Capricorn size 160mm.

Providing and applying of dispersive SBR latex of high dispersive SBR latex for concrete repairs, bonding and water application Make water proofing applications Make-BASF.

Master seal 551

Fibre mesn

Polymix

Master Emaco SBR 2

SUB HEAD - - WATER SUPPLY, DRAINAGE, PUMPS & EQUIPMENT: Supply, assembly, erection, testing and commissioning of pumping system comprising the following:

Carriage of the following materials by Mechanical Transport from source to site of work incl. loading, unloading and stacking complete :- a) Stone aggregate below(Crusher Bajree) 40mm size from Billawar crusher for an average lead of 3.00 Km. by M.T. b) Sand from Billawar crusher for an average lead of 3.00 km. by M.T. c) Bricks from Hiranagar for an av. lead of 70.00 Km. by M.T d) Disposal of earth for an av. lead of 1.00 km. by M.T.

Harish Kohli

vijay builders

M/s Romesh Construction Co