Redevelopment of Thiruvotriyur High road from Tollgate Metro Station to New Washermanpet metro station in Division 39 Zone 04 and Arunachaleswar Koil Street from New Washermanpet Metro Station to QQ scheme road in Division 39 40 Part Zone 04

Amount

Dismantling plain cement concrete work and clearing the debris etc., complete.

Removing C.C Slab Clearing Away And Stacking The Same For Reuse

Cold Milling of Existing Asphalt Pavement to a Required Depth And The Milled Surface To Be Cleaned

Dismantling RCC Slab(reinforcement is being corroded) from Strom Water Drain - Steel is declared unfit for reuse

Removing Cement Concrete Kerbs Clearing Away And Stacking The Same For Reuse

Labour for disconnection of cable and removal of one no of 6 / 7 mt tubular street lamp post with out cable joint

Carting away the surplus earth and debris to a lead of 5 km. including Loading, unloading and dumping in the Corporation Land as directed during the execution.

Cutting bituminous concrete / Cement concrete surface of 300mm thick and width of 300mm using machineries (Jack Hammer) including hire charges of machineries and labour charges etc. complete.

Earth work excavation for foundation in all kinds soils in varying depths including dismantling any masonry or roots met within foundation and shoring with planks, baling water if necessary and filling the sides with excavated earth including clearing and levelling site etc., complete with an initial lead of 10m and lift of 2m.

Plain cement concrete work 1:3:6 (1 cement, 3 Crushed Stone Sand (Commercially called M-Sand) and 6 broken stone jelly 12 to 20mm gauge) including consolidation, curing, etc., complete

Supplying stone dust and filling in regular layers of 15cm thick including watering, consolidating etc. complete for foundation, basement, etc..

Supplying clean Crushed Stone Sand (Commercially called M-Sand) Sand sand and filling in regular layers of 15cm thick each including watering, consolidating etc. complete for foundation, basement, etc

Soling With Gravel to a Consolidated Thickness of 100mm Thick Using 1.333 Cu.m of Gravel For An Area of 10 Sq.m Including Spreading Watering And Consolidation By Power Road Roller Etc. Complete

Providing and laying Tack Coat 2.5 kg/10 m2 with Bitumen Emulsion (Rapid Setting 1)including cost of bitumen emulsion at the site, including labour charges for preparing the surface and applying required quantity of bitumen emulsion as Tack Coat using bitumen sprayer etc., complete over the primed surface as per clause 503 of MoRT& H Specifications Rev.5

Providing and laying Prime Coat 7Kg/10 M2 With Bitumen Emulsion (Slow Setting) Including Cost of Bitumen emulsion At The Site Including Labour Charges For Preparing The Surface And Applying Required Quantity of Bitumen Emulsion As Prime Coat Using Bitumen Sprayer Etc. Complete Over Wet Mix Macadam As Per Clause 502 of Mort & H Specifications.

Providing and laying 50mm consolidated thick Dense Bituminous Macadam using 0.24 m3 of 26.50-13.20mm, 0..25m3 of 13.20-2.36mm and 0.23m3 of 2.36mm & below and with 53.20 Kgs of VG30 bitumen for premixing per 10sqm including cost and conveyance of all materials to CMP site, heating the bitumen and aggregate to required temperature and mixing them in required temperature in central hot mix plant 20-30 ton capacity, conveying the mix by tipper trucks to work site, spreading the mix to uniform thickness of 50mm with paver to the specified grades and cross sections and compacted by Vibratory Roller to the required density etc., including labour for attending to paver at site etc., including hire charges and fuel charges for 20-30 t CMP with bitumen boiler, tipper trucks, 9m paver finisher, Vibratory roller and all other tools and plant required, including fuel and all other incidental charges etc., complete as per specification using CMP as per clause 505 MORTH Rev-5 [The Rate Is Applicable Only If It Is Laid By 9M Paver Finisher]

Providing and laying Bituminous Concrete to 40 mm thick using 0.13 cum of 19.00-9.50mm,0.17 cum of 9.50-2.36mm and 0.26 cum of 2.36 and below with 50.30 kgs of VG40 bitumen for premixing per 10sqm including cost and conveyance of all materials to CMP site, heating the bitumen and aggregate to required temperature and mixing them in required temperature in central hot mix plant 20-30 ton capacity, conveying the mix by tipper trucks to paver site, spreading the mix to uniform thickness of 40mm with mechanical paver to the specified grades and cross sections and consolidated by 8-10 tonne Vibratory / Pneumatic Roller to the required density etc., including labour for attending to paver to site etc., including hire charges and fuel charges for 20-30 t CMP with bitumen boiler, tipper trucks, 9m paver finisher, Vibratory / Pneumatic roller and all other tools and plant required, including fuel and all other incidental charges etc., complete as per specification using CMP as per clause 507 of MORTH Rev-5 (This Rate is applicable only if the work is carried out during night and if it is laid by 9M paver finisher).

Providing and laying of hot applied Thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35. The finished surface to be level uniform and free from streaks and holes etc completed as per MORT& H specification no. 803

Supplying And Fixing of Solar Raised Pavement Markers Made of Polycarbonate Molded Body, Solar Powered, Led Self-Illumination In Active Mode, 360 Degree Illumination And Reflective Panels With Micro Prismatic Lens Capable of Providing Total Internal Reflection of The Light Entering The Lens Face In Passive Mode. The Product Shall Support A Load of 13635 Kg Tested In Accordance To Morth And Astm D 4280 Type H. The Product Should Be Resistant To Water Ingress According To Ip 65 Standards With Is 12063:1987 Category 2 And Should Withstand Temperatures In The Range of - 7 C To 70 C. Flashing Rate And Color of Lighting Is To Be Provided As Per Requirement. There Should Be Minimum Current Losses of Less Than 20 Micro-Amperes In Slcep-Charging Mode To Enhance Product Life And Single Charge Should Provide For A Minimum Dutonomy of 50 Hours. The Height, Width And Length Shall Not Be Less Than 10 mm X 100 mm X 100 mm. Fixing Will Be By Drilling Holes On The Road For The Shanks To Go Inside, Without Nails And Using Epoxy Resin Based Adhesive As Per Manufacturer'S Recommendation And Complete As Directed By The Engineer. Warranty Certificate And Test Reports Confirming To Compressive Strength As Per Morth Circular Shall Be Obtained From The Manufacturer And Submitted To The Engineer-In-Charge. Two Years Warranty Certificate For Solar Rpm For The Quantity Installed And A Certified Copy of Test Reports From An Independent Test Laboratory Conforming To Water Ingress Shall Be Obtained From The Manufacturer By The Contractor And Submitted To The Engineer-In-Charge.

Providing And Fixing of Retro Refelctorised Cautionary ,60 cm Circular Mandatory And Informatory Signs (With Definition Board) Made Out of High Intensity Prismatic Grade Sheeting Conforming To Type – Iv Standards of Irc 67: 2012 And Astm D 4956 – 09, Specification And Fixed Over 2mm Thick Aluminium Sheet Fixed Over A Back Supporting Frame of 25mm X 25mmx3mm. Mild Steel Angel And Supported on a Mild Steel Angel Post 75X75X6mm With A Clear Height of Not Less Than 2.10M From The Ground Level to The Bottom of The Sign Board And 0.60M Below Ground Level. The Sign Post Should Be Painted As Per Irc 67- 2012 And Firmly Fixed To The Ground By Means of Properly Designed Foundation With M15 Grade Cement Concrete 45mmx45cmx60cm Size Including Cost And Conveyance of All Materials, Equipment, Machinery And Labour With All Leads And Lifts, Loading Charges Necessary For Satisfactory Completion of The Work As Directed By The Engineer In Charge. High Intensity Retro – Reflection Sheet Shall Consist of Minimum Coefficient of Retro-Reflection As Per Table 6.6 of Irc 67-2012. The Retro Reflection Sheeting Shall Be Covered Under 7 Years Warranty Issued For Field Performance And a Certified Copy of Three Years Outdoor Exposure Report Shall Be Obtained As Per Irc 67:2012 (As Per Mort&H Specification No.801)

Providing And Fixing of Retro Refelctorised Cautionary, 60 cm X 60 cm Square Mandatory And Informatory Signs (With Definition Board) Made Out of High Intensity Prismatic Grade Sheeting Conforming To Type – Iv Standards of Irc 67 . 2012 And Astm D 4956 – 09, Specification And Fixed Over 2mm Thick Aluminium Sheet Fixed Over A Back Supporting Frame of 25mm X 25mmx3mm. Mild Steel Angel And Supported on a Mild Steel Angel Post 75X75X6mm With A Clear Height of Not Less Than 2.10M From The Ground Level to The Bottom of The Sign Board And 0.60M Below Ground Level. The Sign Post Should Be Painted As Per Irc 67- 2012 And Firmly Fixed To The Ground By Means of Properly Designed Foundation With M15 Grade Cement Concrete 45cmx45cmx60cm Size Including Cost And Conveyance of All Materials, Equipment, Machinery And Labour With All Leads And Lifts, Loading Charges Necessary For Satisfactory Completion of The Work As Directed By The Engineer In Charge. High Intensity Retro – Reflection Sheet Shall Consist of Minimum Coefficient of Retro-Reflection As Per Table 6.6 of Irc 67:2012. The Retro Reflection Sheeting Shall Be Covered Under 7 Years Warranty Issued For Field Performance And a Certified Copy of Three Years Outdoor Exposure Report Shall Be Obtained As Per Irc 67-2012 (As Per Mort&H Specification No.801)

Providing and laying in position, Standardised Concrete Mix M-25 Grade in accordance with IS :456-2000,using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 350 kg/m3 and maximum water cement ration of 0.50, including admixture (Plasticiser/ Superplasticier) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5.0 m3) 7730 kg of 20 mm machine crushed stone jelly and with about (3.3 m3) 5156 kg of 10-12mm machine crushed stone jelly and with about (4.79 m3) 7670 kg of sand, nut excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying,vibrating with mechanical vibrators, finishing, curing, etc and providing complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS Standrands.(No separate payment will be made by the Department for the excess usage of materials)

supply and fabricating of Corrosion Resistant Steel/HCRM bars of Fe-500 D required for all RCC items of works invloved In Bridge Structures in the schedule and cost of TOR steel confirming to IS:1786 at site, including fabrication, labour charges for cleaning the rods, straightening,cutting,bending, type grills with GI wires including overlapping to the required lenght whereever necessary and placing the reinforcement in position as specified in the drawings, including cost of binding wire, provsion of spacer bars, cover blocks and all other charges etc., complete, as per standard specifications Fe-500 D

Supplying and erecting shuttering including necessary supports for plane surface in foundation and basement for RCC column footings, pintol blocks, plinth beam, staircase steps, critical steps, critical piers,etc., using mild steel sheets of size 90 x 60 cm and 10 gauge stiffened with welded mild steel angles of size 25 x 25 x 3 mm for boarding laid over silver Oak (country wood) joists of size 10 x 6.5 cm spaced at about 90 cm centre to centre and supported by casuarina props of 10 to 13 cm dia spaced at 75 cm centre to centre etc., complete.

Supplying and fixing of Rubber moulded Grey Premium Concrete Kerb of Size 450 x 125 x 300 mm using M 30 concrete. The concrete shall be moulded by table mount vibrated with polypropylene fibers at 5% and curing compound. The rate shall Include cost of materials, transportation, loading, unloading charges and all taxes Including necessary earth work, pointing with C.M. 1:3 to full depth curing, thread lining etc complete.

Providing, and fixing all side machine cut granite stone kerbs using 0.40m height, 0.100m thick and 0.6m length granite stone kerb without fragmentation for platform kerbs, including cost and conveyance of granite kerb from available source to work site, including labour charges for fixing the granite and pointing with c.m. 1:3 and all other incidental Charges etc., complete.

Brick work with bricks (9"x4 3/8" x 2 3/4") second class chamber burnt G.M. in C.M.1:6 ( 1 cement and 6 Crushed Stone Sand (Commercially called MSand)) including curing, etc.,Complete,for 23cm thick walls upto basement (upto 1m high aboveG.L.).

Plastering with cement mortar 1:3 (1 cement and 3 Crushed Stone Sand (Commercially called M-Sand)) 12mm thick including curing, etc., complete.

Cement mortar 1:4 (1 cement and 4 Crushed Stone Sand (Commercially called M-Sand))

Supplying And Fixing Rubber Moulded Interlocking Blocks - shot blasted finish Against Available Edge Restraints 60 mm Thick of Approved Design And Pattern of Strength 30 N/Sq.m. 10 mm Iss Metal With Minimum Cement Content As Applicable To M 30 Grade Concrete As Per Is-456-2000 Manufactures By Mechanical Or Hydraulic Machine Using Vibro- Compaction Process And Laid Over 50 mm Thick Laying Course (Bedding) Crushed Stone Sand (M Sand) Well Compacted By Plate Compactor With A Joint Width of 2 mm To 5 mm Including Filling of All Joints With Crushed Stone Sand (M Sand) And Compacting The Paved Surface With Plate Compactor Two Or Three Times Until All The Unit-To-Unit Joints Are Completely Filled With Crushed Stone Sand (M Sand) And Trimming The Edges Neatly Including All Labour Charges And Plate Compactor Charges Etc. Complete (Cost Inclusive of Crushed Stone Sand (M Sand)).

Supplying And Fixing Rubber Moulded Interlocking Blocks Against Available Edge Restraints 80 mm Thick of Approved Design and shot blasted finish And Pattern of Strength 40 N/Sq.m. 10 mm Iss Metal With Minimum Cement Content As Applicable To M 40 Grade Concrete As Per Is-456-2000 Manufactures By Mechanical Or Hydraulic Machine Using Vibro-Compaction Process And Laid Over 50 mm Thick Laying Course (Bedding) Crushed Stone Sand (M Sand) Well Compacted By Plate Compactor With A Joint Width of 2 mm To 5 mm Including Filling of All Joints With Crushed Stone Sand (M Sand) And Compacting The Paved Surface With Plate Compactor Two Or Three Times Until All The Unit-To-Unit Joints Are Completely Filled With Crushed Stone Sand (M Sand) And Trimming The Edges Neatly Including All Labour Charges And Plate Compactor Charges Etc. Complete (Cost Inclusive of Crushed Stone Sand (M Sand)).

Paving the floor with Black Galaxy Granite slab (30mm thick) in floors in C.M. 1:3, 20 mm thick over existing R.C.C. precast work table, etc., complete as directed by the Engineer-in-charge.

Providing And Fixing Machine Dressed Grey Granite Slab (all type of finishes- Lapato finish , leather finish, shot blasted finish) All Sides Machine Cut of Size as per architect design 30 mm Thick Granite Slabs For Platform (Pavement) Including Cost And Conveyance of Granite From Available Source Including Labour Charges For Fixing The Slab In Position To The Line Level And Gradient Including Pointing With cm.1:3 And All Other Incidental Charges Etc. Complete

Supplying and fixing Rajasthan Kota stones (shot blasted finish) 20mm thick of size 60 cm x 60 cm (Mechine edge finishing) over the existing base course including fixing the slab in cm 1:3, etc., complete.

Providing and fixing 10 x 10 x 7.50 cm Granite stone block (Cobble Stone in black color) hand cut and chisel dressed on top, for paving in floors, drains etc. lid over 20mm thick base mortar 1:4 (1 cement : 4 coarse sand) with joints 10mm wide filled with same mortar including ruled pointing etc. Rate of Cement mortar base taken separately complete as per direction of engineer-in-charge.

Providing and fixing 10 x 10 x 7.50 cm Granite stone block (Cobble Stone in grey color) hand cut and chisel dressed on top, for paving in floors, drains etc. lid over 20mm thick base mortar 1:4 (1 cement : 4 coarse sand) with joints 10mm wide filled with same mortar including ruled pointing etc. Rate of Cement mortar base taken separately complete as per direction of engineer-in-charge.

Providing and laying Tactile Paver Type of New Tek BT Yellow Colour Ceramic Tiles (for vision impaired persons as per standards) of size 305 x 305 x 15mm having with water absorption less than 0.5% and conforming to IS:15622 of approved make in all colours and shades in for outdoor floors such as footpath, court yard, multi modals location etc., laid on 20mm thick base of cement mortar 1:4 (1 cement : 4 coarse sand) in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. complete as per direction of Engineer-in-Charge.

Providing and laying first quality Vertified tiles of all colours of size 605mmx605mmx9.6mm in cm 1:3, 12mm thick including pointing with white cement. Labour, Materials, etc. (Relevent ISI std)

Paving hydraulic pressed cement mosaic tiles of approved other colours and of size 20cmx20cmx20mm finished thickness with small verona or Indian Marble Chips (other than Salem Magnesite) with cement mortar 1:3( 1 cement and 3 Crushed Stone Sand (Commercially called M-Sand)) 20mm thick and pointed with same coloured cement including polishing with power polisher to a high degree of polish so as to be perfectly smooth and glossy with other approved colour mosaic tiles,etc.,complete.

Providing & laying Grass Track Paver 40mm - (500x500x40)mm (Thickness), manufactured by using material Recycled PP.HDPE with high strength plymers and UV stabilizers. compressive strength 200tn/sqm and service temperature -30C to 120C and Biological / Chemical resistance- Unaffected by moulds and algae and good resistance to oils acids, alkalis and bitumen, Internal voids area- >95%, Biological Resistance - not affected by biological activity. Chemical resistance - Excellent resistance to acids alcohols, bases and mineral oils, good resistance to Aldehydes , Esters, Aliphatic Hydrocarbons, ketones and vegetables, Recommended services temerature--100C to 1100C The cost is inclusive of all material, installation and transporation charges.

Providing & Fixing of everwood endura decking system as per following specifications:- Exterior grade Everwood WPC - Endura 145mm X 2900mm X25mm thick deck board fitted on slotted virgin aluminium ED50X30x1.5mm thickness framework. Framework fitted on on the firm sub-floor at intervals not exceeding 350mm center to center with Bosch/Fischer - N8/80 expansion screws at intervals not exceeding 750mm. Composite planks fitted on joists with anticorrossive SS304 grade start, center & end clips fastened with anti-corrossive Corroshield 7x25CSK screws.complete as per direction of Engineer-in-charge.

Providing 36 MM EPDM [30 MM SBR & 6 MM EPDM] FLOORINGetc for children play area other necessary fixing arrangement.

Providing and fixing 30 mm thk. stepping stone flooring regular and irragular shape complete as per direction of Engineer-in-charge.

Providing and fixing rough finish stone wall cement mortar 1:6 (1 cement and 6 Crushed Stone Sand (Commercially called M-Sand)) including fixing of bond stone wherever necessary including curing, etc., complete.

Supplying and laying precast a size 300 x 300 x 60 mm thick with Tree Grating perforated hole for perlocation of water and using M30 GRADE concrete inclusive the conveyance of the material form the Manufacturer factory to the site al lead of average 40km and including the sectioning, levelling, laying the good earth for maintain the uniform top level and compacting with earth rammer etc and complete.

Reinforced Cement Concrete Bollards with M20 grade concrete and 150mm dia 4 nos of 10mm dia TMT of overall size 800mm, 100mm projection of TMT Roads at the bottom of the Bollards beyond 800mm for anchor. Black pigment at 4.5 percent weight to cement will be used. Two Strips of Reflective 3M Sticker of width 40mm, including transportation and fixing charges etc, complete.

Supply and fixing of Bollard made from mid steel with CNC machine finishing with 165 mm outer diameter, 140 mm inner diameter and 1030 mm Height. Expose a height 730 mm from above Ground level and fix the remaining 300 mm below the GL. Two number of the circular rib of R10 mm radius are provided at the top and bottom of the bollard. 4 nos of 15mm width retro reflective sheet pasted at the top and bottom groove by hot blow air sticking process for an ambiance look and nighttime visibility. The whole product is power coated as per the standard recommendation of Engineer. For fixing the Bollards with M15 cement concrete 45 cm x 44 cm x 60 cm, 55 cm below ground level with 140dia x 250mm inner sleeve inserted for 150mm below ground level and 100mm projected above ground level. The inner sleeve is fixed with bollard using M16 bolt of 200 mm length.

Supply and fixing of Reinforced cement concrete (M40 grade )Rectangular precast seater box a size 1000mm X 450mm X 450mm with 30 mm thick wall including the transportation form the Manufacture factory to site and placing the seater as directed by Engineer incharge

Supplying and Fixing of CNC cut perforated Enclosure for EB transformer and EB pillar Boxes by using CNC MS Sheet (2mm thick), door hinged with vertical support of 80X40 mm Tubular Post including horizontal Support and Stiffener (40 x40 x2mm) for MS sheet including Powder coating of all structural members and labor for fitting , welding and transportation of the material from the factory to Site as directed by the engineer - in charge.

Supply & Fixing of Floor Mounted Stainless Steel litter bin with Pivot system, Grade SS 304, Satin Finish of Capacity 60 Litres Each bin, Over all Size (L x W x D mm) 1020 x 300 x 1020 (mm), complete with necessary foundation, anchor bolts, base plates, welding, bolts & nuts etc., as per drawing & instructions of the Engineer-in-charge.

Supply & fixing of Stainless Steel Bench (4 Seater) with backrest, Wooden seat cladding, Grade SS 304, Satin Finish including cutting, organ welding, grading, making circustances polishing, buffing etc. complete with necessary foundation, anchor bolts , base plates, bolts & nuts, etc., as per drawing & instructions of the Engineer-in-charge.

Supply & fixing of Stainless Steel Flat Bench (4 Seater) without Backrest, Grade SS 304, Satin Finish including cutting, organ welding, grading, making circustances polishing, buffing etc. complete with necessary foundation, anchor bolts , base plates, bolts & nuts, etc., as per drawing & instructions of the Engineer-in-charge.

Supply & fixing of Stainless Steel Signage for Vinyl pasting, Size - 1.25 M x 3 M Grade SS 304, satin finish including necessary foundation, anchor bolts , base plates, clamps welded on back side as per manufacturer's specification & direction of Architect / engineer in charge

Supply & fixing of Signage with SS Frame, Size 3 feet x 8 feet, back lid, 5mm thick Acrylic sheet advertisement panel, Req: IP 65 STD including cutting, organ welding, grading, making circustances polishing, buffing etc. complete items with necessary foundation, anchor bolts , base plates, bolts & nuts, etc., as per drawing & instructions of the Engineer-in-charge.

Supply & fixing of Signage with SS Frame, back lid, 5mm thick Acrylic sheet advertisement panel, Req: IP 65 STD, crca metal material, digital sinage display, MS metal frame with powder coated, size - 2 feet x 6 feet 55 inch, front touff. Glass 5mm including cutting, organ welding, grading, making circustances polishing, buffing etc. complete items with necessary foundation, anchor bolts , base plates, bolts & nuts, etc., as per drawing & instructions of the Engineer-in-charge.

Supply and Fixing of Puppy Dog Rider: All products must be tested and certified to meet EN 1176 safety standards. The EN 1176 certificates must be issued by a reputed notified International Certifying Body such as IPEMA, TUV, CPSC, or SGS only. The EN 1176 certificates must be in the name of a supplier who has carried out in excess of at least 100 public park projects in India either by themselves or through their dealers or contractors. These EN 1176 certificates must be clearly displayed on the notified certifying bodies websites as online verification is mandatory. HDPE of size 0.83 m x 0.31 m x 0.87 m.

Supply and Fixing of 2 Seater See Saw: All products must be tested and certified to meet EN 1176 safetystandards. The EN 1176 certificates must be issued by a reputed notified International Certifying Bodysuch as IPEMA, TUV, CPSC, or SGS only. The EN 1176 certificates must be in the name of a supplier who has carried out in excess of at least 100 public park projects in India either by themselves or through their dealers or contractors. These EN 1176 certificates must be clearly displayed on the notified certifying bodies websites as online verification is mandatory. The See Saw consists of 2 poles of Dia 114mm and thickness of 2.5mm which balances the horizontal rod at the center which is of size 3110 mm length and Dia 114 mm. It consists of 2 seats which is made of LLDPE virgin plastic of size 305mm X 213 mm X 125 mm. PLAY EQUIPMENT DIMENSIONS: 3.11 m x 0.44 m x 0.66 m

Supply and Fixing of PARALLEL BARS : Upright structural posts of height 2.16 m, 1.56 m are to be schedule HOT DIP Galvanized steel with a 114mm OD and 2.2mm (wall) thickness of the tubing.Handrail AT height 2.0 m, 1.7 m, 1.4 m and Dia 32 mm shall be an all-robotic welded unit, fabricated from 32 O.D. galvanized steel pipes.Bolts, nuts, screws, washers and etc used for assembly shall be stainless steel 304 of tamper resistant stainless steel. Exposed hardware shall be covered with All Joints are robotic welded. All components designed and manufactured to meet with EN 1176 safety standards.PLAY EQUIPMENT DIMENSIONS: 3.6 m x 0.2 m x 2.16 m

Supply and Fixing of Aveo -E :Semi Circular structural posts of height 1.83 m is to be schedule HOT DIP Galvanized steel with a 60 mm OD and 2.2mm (wall) thickness of the tubing.The poles are welded on to a base plate made from steel with 114mm inner diameter.Handrail is of Inverted U Shape of heights starting from 64 mm gradually increases to 357 mm and thickness Dia 32 mm shall be an all-robotic welded unit, fabricated from 32 O.D. galvanized steel pipes.Bolts, nuts, screws, washers and etc used for assembly shall be stainless steel 304 of tamper resistant stainless steel. Exposed hardware shall be covered with safety caps as per EN1176 standards as a safety.All Joints are robotic welded. All components designed and manufactured to meet with EN 1176 safety standards.PLAY EQUIPMENT DIMENSIONS: 2.70 m x 0.89 m x 1.84 m

Supply & Fixing of Lumberjack Logroller - E : LOG ROLLER of Size 900mm x 360 mm [super thick plastic] shall be animated and shall be rotationally molded from antistatic, copolymer, virgin linear low density UV stabilized polyethylene, with color molded in and minimum thickness of 6 - 8mm.Specialized connectors such as clamps and couplings are to be cast from aluminium which is pre treated, and cured, with a baked on powder coat finish.Bolts, nuts, screws, washers and etc used for assembly shall be stainless steel 304 grade and shall be of tamper resistant stainless steel. Exposed hardware shall be covered with safety caps. All joints are Robotic welded. ALL COMPONENTS TO MEET WITH EN-1176 SAFETY STANDARDS .The supplier must have carried out in excess of at least 100 public park projects in India either by themselves or through their dealers or contractors. PLAY EQUIPMENT DIMENSIONS: 1.36 m x 0.36 m x 1.60 m

Supply and Fixing of Creepy Crawly Climber: The equipment comprises of two parallel wavey support bars of height 1.5 m. Handrail of height Dia 32 mm. Exposed hardware shall be covered with ultra violet stabilized plastic safety caps as per EN1176 standards as a safety feature against protruding hardware. All components designed and manufactured to meet with EN 1176 safety standards.PLAY EQUIPMENT DIMENSIONS: 4.54 m x 0.72 m x 1.5 m.

Supply & fixing of BALANCING BEAM : “S” Shaped structural beam of length 2.64 m is to be schedule HOT DIP Galvanized steel with a 114 mm OD and 2.2mm (wall) thickness of the tubing.All post caps are to be cast from aluminum which is pretreated, cured and sandblasted, 114mm diameter.S Balance Beam is supported on the leg of height 530mm of Dia 114 mm and fixed to the Base Plate of Dia 210mmm shall be an all-robotic welded unit, fabricated from 114 O.D. galvanized steel pipes.Bolts, nuts, screws, washers and etc used for assembly shall be stainless steel 304 of tamper resistant stainless steel. Exposed hardware shall be covered with safety caps as per EN1176 standards. All joints are Robotic welded. All components designed and manufactured to meet with EN 1176 safety standards. PLAY EQUIPMENT DIMENSIONS: 2.64 m x 0.49 m x 0.64 m

Supply and Fixing of Tunnel - X: The Tunnel of Dia 0.83 m supported on the U-Shaped metal frame made from pipe of dia 32mm, Plastic Components shall be animated and shall be rotationally molded from antistatic, copolymer, virgin linear low density UV stabilized polyethylene, with color molded in and minimum thickness of 6 - 8mm. Specialized connectors such as clamps and couplings casted from aluminum alloy which is pretreated, cured and sandblasted and finished with a baked on powder coat finish using AkzoNobel INTERPON coatings are used to connect the various components of the playground. Bolts, nuts, screws, washers and etc used for assembly shall be stainless steel 304 of tamper resistant stainless steel. Exposed hardware shall be covered with safety caps as per EN1176 standards. All joints are Robotic welded. All components designed and manufactured to meet with EN 1176 safety standards.PLAY EQUIPMENT DIMENSIONS: 2.80 m x 1.22 m x 2.5 m

Supply & Fixing of WEB CLIMBER : Support posts of height 2.1 m are to be schedule Galvanized steel with a 89 mm OD.Bolts, nuts, screws, washers and etc used for assembly shall be stainless steel 304 grade and shall be of tamper resistant stainless steel. Exposed hardware shall be covered with afety caps as per EN1176 standards. All joints are Robotic welded. All components designed and manufactured to meet with EN 1176 safety standards.PLAY EQUIPMENT DIMENSIONS: 1.77 m x 0.5 m x 2.1 m

Supply & Fixing of Straight Rope Climber: Support posts of height 2.2 m are to be schedule Galvanized steel This equipment comprises of 2 poles of size Dia 114 mm and thickness of 2.5 mm. The Climber is made of cross ropes of Dia 20 mm and the total structure is of dimensions 1790 mm x 1760 mm which is connected to a metal frame of Dia 48 mm. Bolts, nuts, screws, washers and etc used for assembly shall be stainless steel 304 grade and shall be of tamper resistant stainless steel. Exposed hardware shall be covered with safety caps as a safety. All joints are Robotic welded. All components designed and manufactured to meet with EN 1176 safety standardsPLAY EQUIPMENT DIMENSIONS: 2.30 m x 0.30 m x 1.5 m 1

MATERIAL DESCRIPTION:Panels: HPLPosts: Carbon steel S-235 with electrolytic zinc.Paint: 1 coat of dust lacquer formed by the mixture of polyester resin, hardeners and colour pigments. Free of lead and high resistence to weather detoriation.Plastic Parts: Polypropylene, high density polyethene and polyamide.Metallic Parts: Steel S-235.Fixings: Steel conforming to 8.8 DIN267, AISI-304 & AISI-316.All joints are Robotic welded. All components designed and manufactured to meet with EN1176 safety standards.Maximum dimensions of parts: 60x25x25 cm.

MATERIAL DESCRIPTION:Plastic Parts: Polypropylene and rubber.Metallic Parts: AISI-304 steel.Fixings: Steel conforming to 8.8 DIN267, AISI-304 or AISI-316.All joints are Robotic welded. All components designed and manufactured to meet with EN1176 safety standards.Maximum dimensions of parts: 175x179x40 cm.

MATERIAL DESCRIPTION:Panels: 15 mm HPL board.Posts: Carbon steel S-235 with electrolytic zinc and lacquer.Plastic Parts: Polyethene, polypropylene, polyamide and rubber.Metallic Parts: Zinc coated and lacquered steel S-235, AISI-304 and aluminum, 2024-T4.Fixings: Steel conforming to 8.8 DIN267, AISI-304.Paint: 1 coat of dust lacquer formed by the mixture of polyester resin, hardeners and colour pigments. Free of lead and high resistence to weather detoriation. All joints are Robotic welded. All components designed and manufactured to meet with EN1176 safety standards.Maximum dimensions of parts: 463x226x23 cm.

MATERIAL DESCRIPTION:Panels: 15 mm HPL board.Posts: Carbon steel S-235 with electrolytic zinc and lacquer.Plastic Parts: Polyethene, polypropylene, polyamide and rubber.Metallic Parts: Zinc coated and lacquered steel S-235, AISI-304 and aluminum, 2024-T4.Fixings: Steel conforming to 8.8 DIN267, AISI-304.Paint: 1 coat of dust lacquer formed by the mixture of polyester resin, hardeners and colour pigments. Free of lead and high resistence to weather detoriation. All joints are Robotic welded. All components designed and manufactured to meet with EN1176 safety standards.Maximum dimensions of parts: 451x227x23 cm.

Supplying and erecting in position LIGHT DUTYAluminum section as per the drawing. The materials and design of the member should confirm to the relevant Indian Standard specification. The section shall be procured only from reputed manufactures of alumnium section with prior approval of the Buildings Engineer and a certificate to the effect from the reputed manufacturers shall also be furnished with design. The rate quoted shall include the cost of section. Base-plate with holding down bolts and nuts to RCC or Masonry works, roof purlins, rafters, purlin sleeves, the members fixing accessories etc., painting one coat of red-oxide paint and erecting in position etc., complete as directed during execution. The contractor shall also arrange to provide grouting for holding down bolts embeding the end purlins, to the gable wall wherever necessary etc.,

Supplying and erecting in position LIGHT DUTY STEEL TRUSSES as per the drawing. The materials and design of the trusses should confirm to the relevant Indian Standard specification. The trusses shall be procured only from reputed manufactures of trusses with prior approval of the Buildings Engineer and a certificate to the effect from the reputed manufacturers shall also be furnished with design. The rate quoted shall include the cost of trusses. Base-plate with holding down bolts and nuts to RCC or Masonry works, roof purlins, rafters, purlin sleeves, the members fixing accessories etc., and including one coat of anticorrosive paint and over it two coats of oil painting of approved quality and shade etc. complete. and erecting in position etc., complete as directed during execution. The contractor shall also arrange to provide grouting for holding down bolts embeding the end purlins, to the gable wall wherever necessary etc., The roof sheeting shall project 0.762m from the eves purlins. For structures like CYCLE STAND, PARKING GARAGE, TEMPORARY ENCLOSERS

Providing and fixing Stainless Steel .S. ERW P hollow section of various thickness and sizes in square, rectanular and round shape from 25mm to 450mm section including frame of grade 304 pipes with braces of S.S. grade 304 and rectangular section including cutting, organ welding, grading, making circustances polishing, buffing etc. complete with necessary holes, nuts & bolts, caps & anchor plates of S.S. grade 304 ASTM as per drawing & instructionsof the Engineer-in-charge excluding the cost of RCC/CC and earth work.

Supplying and painting with two Coats Ready Mixed epoxy paint first class quality and of Approved colour over existing painted Metal structural using brush including necessary Scaffolding, thorough Cleaning, Washing, Clean removal of dirt etc., Complete and necessary plaster or paris putty etc., Where ever required (ISI Std.)

Art work as per the direction of department official, over Oil Painting with first class quality and approved colour including a priming coat with thorough scrapping clean removal of dirt., etc., complete and including necessary plaster of paris, putty, etc., wherever required (Relevent ISI STD), including putty works.

Random rubble masonry work in cement mortar 1:6 (1 cement and 6 Crushed Stone Sand (Commercially called M-Sand)) including fixing of bond stone wherever necessary including curing, etc., complete.

Geosynthetic Drainage with Two Filtering Non-woven Geotextiles having a “W” configuration as longitudinal parallel channels. Minimum thickness to be 7.2 mm, with two filtering UV stabilized polypropylene non-woven Geotextiles of minimum thickness of 0.75 mm having pores of 150 micron and tensile strength of 8.0 kN/m and having plane flow capacity of 2.1 L / (m.s) at hydraulic gradient of 1.0 & 20 kPa pressure, tensile strength of 18 kN/m with mass per unit area of 740 gsm.

Providing GI Barricading of size 3 m height w including Cutting, Welding, fabrication charges with fixing of indication with reflecting stickers and necessary interlocking arrangements with adjoining units and placing the barricading units as directed The GI. Sheet barricading is a temproray barricading and can be removed and reused after the completion of work in a particular stretch.

Construction of Modular type RWH Structure capacity of 4.32 cu.m by using infiltration modules of size 800 x 800 x 360 mm and side wall with infiltration modules of size 800 x 360 x 25 mm including earthwork excavation in bitumen/concrete roads to a size of 1200 x 1200 x 3000 mm and providing base plate, Geo - textile 400mm - 200 micron, Fine filter media 12mm thickness, Coarse filter media 20mm thickness, FRP of 700x700mm (clear opening 600x600mm) (Grating cover with Frame - Medium duty 10 MT), including all labour charges, carting away etc., complete.(Model 5)

Supplying and fabricating of stainless steel pipe 50mm dia (14gauge) 316 grade with base plate and clamp fixing including polishing and generator charges etc.

Design, fabrication and installation of simple vault tensile fabric work and Steel structure using Belgian make tensile polyester fabric, steel frames by ISO standard acclaimed CE certified installer with structural stability vetting from Anna university ,Chennai having using FLUOMAX Coated Architectural Membrane having tensile strength not less than 4300 N/50mm/ 4200 N/50mm (Warp/ Weft) and Tear strength not less than 600 N/ 500 N (Warp/ Weft) of make SIOEN Belgium or equivalent, cables, complete perimeter attachment system, and all normally associated components 282 PD-1564 with machines for Fabrication using swiss make Zund cutting machine and Belgian make Architectural Membrane on 20KW Forsstrom High Frequency Welding Machine with SEAMLESS WELDS 50 mm weld width X 1400 mm- Single Stroke all PVC joints shall be formed to a tolerance of +1mm, -1mm and shall be assembled to ensure that seams are always single laid and attaining seamless finish by that a cut edge does not face uphill and membrane used to have a double lacquering made out of highlyconcentrated FLUOMAX PVDF on both side, double PVC coating and be weldable without grinding to

Supplying and erecting in position of 1000 liters capacity Industrial Model Reverse Osmosis Water-cum-purifier to deliver Potable Water with world Health Organisation (WHO) Standards with following accessories (a) MS Skid – 1No (b) Media 11054 No, Vessel with 20 bb Multiport Valve (with Media Pubble and Fine Sand and Activated Carbon Filling) set (c) Feed Pump 0.50 HP – 1 No. (d) Vertical Pump 2-9, 2.00HP / Single Phase – 1 No (e) Membrane 40 x 40 filmtech (or) equilaents / Osmonic (USA) – 1 No. and Membrane Pressure Vessel 40 x 40 – 1 No. & Pressure Gauge – 2 Nos. (f) Flow Meter – 1 No. 20” Filter with Housing – 1 No., Low Pressure Switch – 1 No., Level Switch – 1 No. & Necessary CPVC Pipes and Fittings. 1000 Litres

Providing and fixing Glass Reinforced Concrete (G.R.C) ornamental Screens casted with 'Spray Mix' concrete design in approved size, pattern, thickness (Border 40-50mm thick & Internal Mamber 25-30mm thick) and shade. The Screens should be made from ‘53 grade’ White Portland Cement, White Quartz fine graded sieve Silica Sand, Alkali Resistant Glass Fiber, Super Plasticizers, Polymers and U.V resistant Synthetic inorganic pigments should be used for pigmentation. The Screens casting shall take place with layering methodology using- Direct Power Spray machines. The GRC Screens flexural strength average L.O.P should be above or equivalent to 6 N/mm2 & M.O.R should be above or equivalent to 12 N/mm2 for tests done on 28 days cured samples.The fixing of Screens should be done using ‘Dry fixing’ method onto structural support members i.e. R.C.C, Brick work or Red oxide Primer - paint or Epoxy primer -paint treated mild steel. The fixtures, fasteners and self tapping screws to be used for dry fixing should be of P / HILTI / KLIMAS / Fischer / Wurth / MUNGO. The quantity of fasteners or self tapping screws shall be calculated in accordance to the weight of Screens and actual site fixing conditions. If there will be a requirement of Joint filling then Elastomeric exterior grade paintable PU Sealant will be used. For final finishing of Screen one weathershield exterior grade water based diluted paint coat will be done if required. Vendors shall submit shop drawings of the same, the drawings to be duly approved by the Engineer in charge or Architect.

Supply & Installation of MS CNC Laser Cut Panel of below mention thickness, Aesthetic fixture made of MS, as per design & drawing given by architect. Item include cost of ms sheet, cutting & installation on site. All work to be completed as per instruction of Site in charge. - 6 mm thick ms sheet

Supply & Installation of MS CNC Laser Cut Panel of below mention thickness, Aesthetic fixture made of MS, as per design & drawing given by architect. Item include cost of ms sheet, cutting & installation on site. All work to be completed as per instruction of Site in charge. - 8 mm thick ms sheet

Supply and installation of Terracotta jaali 200x200x60mm, as per design & drawing given by architect. Item include cost of installation on site. All work to be completed as per instruction of Site in charge.

Supply of chemical adhesive to fix the terracotta jaali

Providing & Fixing of ACP Alucobond Cladding system as per following specifications:- with necessary hardware like screw , PVC Plug , SS starter Clip & PVC Decking clips and L-Cleat. inculding all the materila labour. complete as per direction of Engineer-in-charge.

Providing & Fixing of WPC cladding system as per following specifications:- Exterior grade WPC - Endura 156mm X 2900mm X21mm thick deck board fitted on slotted virgin aluminium L-Profile size 2900x50x50mm. The system will be installed using Aluminium section (38x25x1.3mm) and Aluminium L Angle (38x25x2.5mm) for cladding and using with necessary hardware like screw , PVC Plug , SS starter Clip & PVC Decking clips and L-Cleat. inculding all the materila labour. complete as per direction of Engineer-in-charge.

Supply & Installation LAMINATED GLASS of 5 mm clear toughend glass + 1.52 clear PVB layer + 5 mm clear toughend glass s per design & drawing given by architect.

Supply & installation of 16mm thk. Multicell structure modular panel polycarbon sheet with 2 side Uv layer as per your approved shade and finished as per architect's provided drawings and specification.

Providing and fixing 8mm thick corten steel plate signage etc with necessary clamps welded on back side asper manufacturer's specification & direction of Architect / engineer in charge

Providing and fixing acrylic plastic sheet panels of approved quality in required thickness plain clear or any colour or obscured linings in lieu of glass pans to doors/windows including providing and fixing clips, putty etc. complete. (b) 4.00 mm thick.

Providing and erecting chain link fencing as required. height with G.I. chain link of size 50 x 50 mm, 8 gauge thick and fixed 75 mm above ground level on vertical M.S. Angles of 40 x 40 x 6 mm size, includind excavating pits for foundation and embedded in C.C. block of 1:4:8 mix of size 450 x 450 x 670 mm. at 1.75 M. c/c with iron bar 16mm dia as hold fast including welding link with angle frame at 30 cm c/c with nuts and bolts and horizontal M.S. Angles at top and bottom of 25 x 25 x 5 mm size and vertical M.S. flat 35 x 5 mm and 25 x 5 mm horizontal including cross support of 40 x 40 x 6 mm angles both side at every corner or bend embedded in concrete blocks of 1:4:8 of size 450 x 450 x 670 mm including 3 coats of oil painting etc. complete.

Providing and fixing in position Natural rocks irregular shape 1 x 1 m, 200-300 mm maximum sized, Irregular shaped natural Rock as per design as instructed by Site in charge for edge stabalisation. The design should be approved by the Architects. It should be kept random, stable, natural, crack proof durable, environment friendly. Item include all the labour required for fixing of rocks, machinery for lifiting and placing of rocks, transportation. Complete.

Providing and fixing in position Rock sculpture as per design as instructed by Site in charge for edge stabalisation. The design should be approved by the Architects. It should be kept random, stable, natural, crack proof durable, environment friendly. Item include all the labour required for fixing of rocks, machinery for lifiting and placing of rocks, transportation. Complete.

Providing, fixing, laying, in position river pebbles of desired color, shape and size (200-150mm), (50-100mm) as per the instruction of site incharge. The shape, size, color of stone should be approved by architect. It sholud be placed in position as per the Architectural design.

Providing & Fixing Stainless Steel STAINLESS STEEL 304 cable Railing STAINLESS STEEL JINDAL MATERIAL WITH TC 50mmx50mm handrail, 40mmx40mm vertical, 6mm cable rope horizontal , railing height 1000mm, Railing mat finished design as per architects approval .Item to be installed as per vendor's specification & complee as per direction of Engineer-in-Charge.

Providing FRP 10000 Liter UG SUMP Basic Price @ R@ Rs.18 Per Liter Size(mm): Dia 7 Feet x Length 9.50 feet Approx., Inlet pipe diameter 6 inch” Outlet Pipe diameter 4 inch” Gas pipe diameter 2 inch”, Wall Thickness: 8-9mm, Main Hole 2 Nos.

Providing FRP 20000 Liter UG SUMP Basic Price @ R@ Rs.18.25 Per Liter Size(mm): Dia 7 Feet x Length 19 feet Approx., Inlet pipe diameter 6 inch” Outlet Pipe diameter 4 inch” Gas pipe diameter 2 inch”, Wall Thickness: 8-9mm, Main Hole 2 Nos.

Providing & Fixing Stainless Steel Sculpture Art Material S S 304 Grade Jindal , Sculpture Size 2500Mm Height 1500Mm Width, 3Mm Thickness And 5Mm Thickness Sheet , With Laser Cutting, Fabrication Nd Finishing , Stain Mat Finished. design as per architects approval .Item to be installed as per vendor's specification & complee as per direction of Engineer-in-Charge.

Construction of temporary wooden foot bridge for pedestrian traffic with causurina posts for vertical, horziontal, runner, crossstiffners, diagonal brace, incline props, handrailing and with 4 cm thick wooden planks nailed to country wood runners 3"x2" etc., complete.

Hire charges for diesel pumpset for 10HP with fuel and crew charges including transportation

Mazdoor for Traffic diversion un-skilled category-II (Wardans)

Supply, Installation, Testing & Commissioning of Interractive Water Fountain with Multi Colour Illumination suitable for 7.2mtr dia Fountain Equipment/Nozzles -24no. 23mm Foam jet(Bronze) with Ball joint(Brass) with Inlet Pipe arrangements as required. Interconnecting Plumbing -between Pumps and Fountain Nozzles with UPVC pipes(sch 40) & UPVC Fitting(sch 80) and Control Ball valves (UPVC) as required. Pump -of 1no. Submersible pumpset for Fountain operating on 3phase 415V AC Supply having 760LPM Discharge at 8mtr Head (3HP) & 1no. Submersible pumpset for Fountain operating on 3phase 415V AC Supply having 1600LPM Discharge at 8mtr Head (7.5HP) with suitable pipe connection and 2no. stainless steel 304 grade Suction Strainer as required. Pump make- KIRLOSKAR Illumination - 24no. Stainless steel body Underwater light fitting IP68 grade operating on 12V DC Supply - 24W LED Bulb RGB including fixing clamps and necessary Looping Cables within the Pond as required. Interconnecting Control Cables -Submersible cables of suitable sizes - 2Runs x 4Core x 2.5sqmm Copper Coductor Round Flexible cable and 2Run x 3Core x 4sqmm Copper Coductor Flat Flexible cable and Earthing Conductors including suitable PVC junction boxes with terminations with suitable PVC Conduit pipes from Fountain Pond to Control Panel (approximately 30mtr) as required.Cable make- POLYCAB/FINOLEX SS Mesh Cover-4' x 3' size of wire mesh of size 20mm x 20mm x 2mm thick made up of stainless steel 304 grade materials and covered with 1mm opening fine mesh (ss304) to protect the pump from the dust and garbage articles etc,. as required. Music System- Music system consists of 1no. PA Amplifier with Built-in Digital Player model-TZA-7000DP, 2nos. Box speakers model-SRX 500 with necessary Junction boxes, Interconnecting wiring between Speakers, PA Amplifier with suitable wires and PVC coduit pipes & fittings as required. PA system make- AHUJA Fountain Controller Unit- Outdoor type Control Panel made out of MS sheet including Door with locking arrangement with powder coated finish along with – 1no. 100A TPN Incoming MCCB, 2nos. Starters with O/L Relay for Pump, 1no. single preventor, 1no. 2 Pole MCB for Lights, 2no. 230v/12v DC Power supply for Lights, 2no. RGB Controller Unit for Lights Colour changing, 2no. 24Hrs Timer for Automatic ON/OFF (for Pump and Light) including Panel wiring etc,.as required.

Providing and laying Non Pressure NP-3 class (Medium duty) R.C.C. pipes, upto the depth of 1.0 mt., including collars / spigot jointed with stiffmixture of spun yarn or rubber gasket with cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including laying, aligining with proper gradient conveyance, labour, testing of joints etc. complete compliance with standard specifications as per the instruction of departmental officers. - 300 mm dia. R.C.C. pipe

Providing and laying Non Pressure NP-3 class (Medium duty) R.C.C. pipes, upto the depth of 1.0 mt., including collars / spigot jointed with stiffmixture of spun yarn or rubber gasket with cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including laying, aligining with proper gradient conveyance, labour, testing of joints etc. complete compliance with standard specifications as per the instruction of departmental officers. - 200 mm dia. R.C.C. pipe

RCC non pressure spun pipe with socket and spigot ends as per IS 458/2003 manufactured with sulphate resistant cement with 12 mm HI -alumina lining provided for rubber ring joints. (Internal diameter - 900mm)

RCC non pressure spun pipe with socket and spigot ends as per IS 458/2003 manufactured with sulphate resistant cement with 12 mm HI -alumina lining provided for rubber ring joints. (Internal diameter - 600mm)

Hoisting and fixing of NP3 class RCC Pipe and collars in proper gradient and jointing pipe with collar by packing cement slurry dipped hemp yarn and packed with cement mortar 1:5 including all labour charges and all other incidental charges etc., complete (900 mm dia)

providing and laying precast saucer type drain of size 600 x 300 x 50mm with M30 GRADE concrete including the Cutting of the existing bituminous surface of 10 cm thicckness and PCC of 1:3:6 for leveling and maintain the gradient to drain the water from raod to Storm water Drain etc and complete.

Providing of 7 way 40 mm Multi Ducts with solid permanently solidly lubricated silicore in inner layer for ICT fibre cables conforming to ASTMF 2160, ASTM D 2444 and / or equivalent Indian Standard. External sheath shall be in orange color and shall be freen from visual defects like blisters, shirnk holes, flaking scratches, groove lines & surface roughness. the color of the 7 nos. PLB HDPE ducts shall be green, blue, yellow, brown, voilet, grey, red for differentiation. outer sheet thickness shall be 1.2 mm, 0.2mm. The inner surface of multi channel ducts shall be spirally ribbed & shall be of a configuration for faster installation of cables. Wall thickness (mm) of each of ducts excluding rib height shall be 2.9 mm 0.3 mm. ISO Requirements - ISO 9001, 14001, 18001, complete as per specifications and directions of Engineer - in - charge.

Construction of cast -in- situ Silt Catch Pit of inner size 450 X 450 X 450 mm including necessary earth work excavation including providing foundation in PCC 1:5:10 under wall 150mm thick and fixing vertical grating of size 450mm x 155mm x 30mm on the storm water drain mouth with RCC cast in situ wall of size 120mm in RCC 1:1.5:3 with steel of 9.25 kg including fixing FRP Grating Cover with frame of size 550 x 550mm (clear opening 450 x 450mm) -10 MT -completing the finishing work etc.

Construction of cast-in-sit Silt Catch Pit with Rain Water Harvesting Structure (Every 30m) of inner size 600x600x600mm including necessary earth work excavation inclulding providing foundation in PCC 1:4:8 under walls 150mm thick and fixing vertical grating of size 450mm length x 155mm height and 30mm thick on the storm water drain mouth, with RCC cast in situ wall of size 120mm in RCC 1:1.5:3 with steel of 10.60kg including fixing FRP Grating Cover with frame of size 700mmx700mm (Clear opening 600x600mm) - 10MT completing the finishing work etc., cost per each number. Using Hand Bore Set drilling of bore hole of 300mm dia upto 4.35m depth including shifting of the hand bore from one place to another place within 5km and filling in with 40mm HBG metal with 200mm dia slotted PVC pipe 6kg/cm2

Power: (Large Access, Multi Part) Recessed Single Seal RED 324 SSRH – 3 * 900 x 600mm DI MANHOLE COVER & FRAME IN D400 LOAD CLASS , Black Bitumen Paint For power manhole LT

Telecom: Recessed Double Seal RED 261 DSRH – 800 x 800mm DI MANHOLE COVER & FRAME IN D400 LOAD CLASS , Black Bitumen Paint For Telecom manhole

Storm Water: Recessed Double Seal RED 042 DSRH – 600 x 600mm DI MANHOLE COVER & FRAME IN D400 LOAD CLASS , Black Bitumen Paint For Storm Water Chamber - On Footpath

Providing FRP 10000 Liter UG SUMP Basic Price @ R@ Rs.18 Per Liter Size(mm): Dia 7 Feet x Length 9.50 feet Approx., Inlet pipe diameter 6 inch” Outlet Pipe diameter 4 inch” Gas pipe diameter 2 inch”, Wall Thickness: 8-9mm, Main Hole 2 nos.

Providing FRP 20000 Liter UG SUMP Basic Price @ R@ Rs.18.25 Per Liter Size(mm): Dia 7 Feet x Length 19 feet Approx., Inlet pipe diameter 6 inch” Outlet Pipe diameter 4 inch” Gas pipe diameter 2 inch”, Wall Thickness: 8-9mm, Main Hole 2 nos.

Pipes Work: Supply, laying & commissioning in position PVC pipe conforming to IS:4985:2000 and suitable for the respective working pressures without all fittings and accessories e.g. couplings, tees, bends, reducers, screwed adapters, flanged tail pieces etc., complete, as per the instructions of Architect/Landscape Architect/Engineer In Charge.: PVC pipe 90mm-10 kg/cm² -Mainline

PVC pipe 75mm-10 kg/cm² -Mainline

PVC pipe 63mm-6 kg/cm²

PVC pipe 50mm-6 kg/cm²

PVC pipe 40mm-6 kg/cm²

PVC pipe 25mm-10 kg/cm²

PVC pipe 20mm-10 kg/cm²

Earth work excavation and refilling 300x450mm

Earth work excavation and refilling 300x300mm

DRIP NET PC AS 16008 2.0L/H 0.30M 500M including installation charges.

Supply,Fixing & commissioning of 2" Large Capacity Y Type Disc / Screen Filters for submain filteration Have High Flow & Low Maintenance With a Solid Build,Maximum Flow Up to 110 gpm (25m³/hr), Maximum Pressure 116 psi (8 bar),Maximum Temperature Up to 140ºF (60ºC) etc., complete, as per the instructions of Architect/Landscape Architect/Engineer In Charge.

Supply,Fixing & commissioning of 1.5" Large Capacity Y Type Disc / Screen Filters for submain filteration Have High Flow & Low Maintenance With a Solid Build,Maximum Flow Up to 88 gpm (20m³/hr), Maximum Pressure 116 psi (8 bar),Maximum Temperature Up to 140ºF (60ºC) etc., complete, as per the instructions of Architect/Landscape Architect/Engineer In Charge.

Supply,Fixing & commissioning of 1" Large Capacity Y Type Disc / Screen Filters for submain filteration Have High Flow & Low Maintenance With a Solid Build,Maximum Flow Up to 26 gpm (6m³/hr), Maximum Pressure 116 psi (8 bar),Maximum Temperature Up to 140ºF (60ºC) etc., complete, as per the instructions of Architect/Landscape Architect/Engineer In Charge.

Supply,Fixing & commissioning of 40mm dia self-closing flushing valves that are installed at the end of the irrigation line for effecting flushing of the line at the beginning of every irrigation cycle, thus avoiding the clogging of the emitters /sprinklers through removal of particles, sediments and other impurities from the water. etc., complete, as per the instructions of Architect/Landscape Architect/Engineer In Charge.

Supply,Fixing & commissioning of 9 - Gauge Galvanized Steal Rod Comes Sharp tips provide easy insertion into all soil types, Staple Distribution Tubing , XF Drip Line or XBS Tubing to Finished Grade. Notched Sides. Corrosion -Resistant of TIE DOWN STAKE etc., complete, as per the instructions of Architect/Landscape Architect/Engineer In Charge.

Supply of endcap, nipple, start nipple, rubber grommet 16 mm dia. "Netafim" including installation charges.

Supply,Fixing & commissioning of High Quality Barbs Grab Tubing for a Secure Fit. Unique Barb Design to Reduce Insertion Force. Non - Obtrusive Brown Colored Fittings of 17mm Tee . etc., complete, as per the instructions of Architect/Landscape Architect/Engineer In Charge.

Supply,Fixing & commissioning of High Quality Barbs Grab Tubing for a Secure Fit. Unique Barb Design to Reduce Insertion Force. Non - Obtrusive Brown Colored Fittings of 17mm COUPLING. etc., complete, as per the instructions of Architect/Landscape Architect/Engineer In Charge.

Supply,Fixing & commissioning of High Quality Barbs Grab Tubing for a Secure Fit. Unique Barb Design to Reduce Insertion Force. Non - Obtrusive Brown Colored Fittings of 17mm ELBOW. etc., complete, as per the instructions of Architect/Landscape Architect/Engineer In Charge.

Supply,Fixing & commissioning of Pop up spray head1804 Series Spray bodies, with Rotary nozzle having mutilple stream MPR sprayhaving Co-moulded wiper seal is molded into the cap and features an encased plastic 'cage' to provide unmatched resitence to grit, nozzle capable of covering 2.4m to 7.3 at 1.4 - 3.8 Bars pressure, and the enviroment. Rotary nozzles shall have hand adjustable ( without tools) radius and arc-45 to 270 degree or full circle,True flushing mechanism,Thick streams and large water droplet & Low precipitation rate Additionally, the pressure-activated, multi-function seal design assures a positive seal without excess'flow-by'which enables more heads to be installed on the same valve, Two-piece ratchet mechanism, Features is Precision controlled flush at pop-down clears debris from unit, Construction of time-proven UV_resitant plastic.Pop spray body shall with stand upto 4.8 bar.etc., complete, as per the instructions of Architect/Landscape Architect/Engineer In Charge. 1804 R1724

Supply,Fixing & commissioning of 5004 Series Rotor pop up sprinkler full/part circle having radius of 6.7m - 12m @ 2.5 - 4.5 bar with discharge of 0.09 - 0.61 ltr./sec. The sprinkler is gear driven rotary type with having 3/4" bottom inlet. Oversized wiper seal, Rain Curtain technology, gentle close-in watering and Self-flushing arc adjustment port and Reversing full- and part-circle adjustment 40° - 350° and also having tapered riser stem with Wiper Seal The body of sprinkler is of non - corrodible, heavy duty, ABS plastic. O-ring Slip Clutch,Racheting Slip Clutch,Side Inlet Available 6" and 12",Turret-mounted ID Plugs,Flow Stop Available,Non-potable water indication available etc., complete, as per the instructions of Architect/Landscape Architect/Engineer In Charge.

Supply,Fixing & commissioning of 1/2" Pop up Connecting Swing joint Assembly. The tubing shall be made of polyetylene having wall thickness of 2.3mm ,a working pressure of 5.5 kg/cm2 at 43oC and a surge pressure of 16.6 kg/cm2. Flex pipe textured for wet conditions.The fittings shall be made of UV resistant thermo plastic etc., complete, as per the instructions of Architect/Landscape Architect/Engineer In Charge..SA Series.

Supply,Fixing & commissioning of 3/4" Pop up Connecting Swing joint Assembly. The tubing shall be made of polyetylene having wall thickness of 2.3mm ,a working pressure of 5.5 kg/cm2 at 43oC and a surge pressure of 16.6 kg/cm2. Flex pipe textured for wet conditions.The fittings shall be made of UV resistant thermo plastic etc., complete, as per the instructions of Architect/Landscape Architect/Engineer In Charge..SA Series.

Supply of Imported HDPE service saddle of varying size including installation charges.

Supply,Fixing & commissioning of PVC Single Union Ball Valve,security pivot to maintain lever in space,double water tight joint,direct injection stem,Stem O-Ring, non mechanical ,ball Seals with backing seals and with a base which permits maximum penetration into the valve of size 63mm with pressure rating PN 10 etc., complete, as per the instructions of Architect/Landscape Architect/Engineer In Charge.

Supply,Fixing & commissioning of PVC Single Union Ball Valve,security pivot to maintain lever in space,double water tight joint,direct injection stem, Stem O-Ring, non mechanical ,ball Seals with backing seals and a base which permits maximum penetration into the valve of size 50mm. with pressure rating PN 10 etc., complete, as per the instructions of Architect/Landscape Architect/Engineer In Charge.

Supply,Fixing & commissioning of PVC Single Union Ball Valve,security pivot to maintain lever in space,double water tight joint,direct injection stem,Stem O-Ring, non mechanical ,ball Seals with backing seals and with a base which permits maximum penetration into the valve of size 40mm. with pressure rating PN 10 etc., complete, as per the instructions of Architect/Landscape Architect/Engineer In Charge.

Supply,Fixing & commissioning of a double acting air and vaccum release 1/2 " Air release valve . The Air release valve shall be capable of both releasing and admitting air from and into the line. The working pressure shall be 5 bar. Only for Drip Irrigation etc., complete, as per the instructions of Architect/Landscape Architect/Engineer In Charge.

Supply,Fixing & commissioning of a double acting air and vaccum release 2 " Air release valve . The Air release valve shall be capable of both releasing and admitting air from and into the line. The working pressure shall be 10 KSC etc., complete, as per the instructions of Architect/Landscape Architect/Engineer In Charge.

Supply of 6"Round box with greenlid and corrugated structure with unique shovel access slot and bolt hole knockout.

Supply of 10" Round valve box with greenlid and corrugated structure with unique shovel access slot and bolt hole knockout

Supply,Fixing & commissioning of 12" Rectangular Standard Valve Box with greenlid and corrugated structure with unique shovel access slot and bolt hole knockout & having Dimensions @ Top Opening:18 1/4" L X 13" W & bottom opening :21 1/4" L X 15 15/16"W X 12" H etc., complete, as per the instructions of Architect/Landscape Architect/Engineer In Charge.

Supply,Fixing & commissioning of 18'' Jumbo Rectangular Standard Valve Box with greenlid and corrugated structure with unique shovel access slot and bolt hole knockout & having Dimensions @ Top Opening:18 1/4" L X 13" W & bottom opening :21 1/4" L X 15 15/16"W X 12" H etc., complete, as per the instructions of Architect/Landscape Architect/Engineer In Charge.

Supply of Quick coupling valve made up of Aluminium with locking cover corrosion resistant and stainless steel spring

Supply of Key threads into top of QCV to provide water access.

Supply,Fixing & commissioning of 3/4th inch Hose Swivel Made up of Solid Brass Swivels up to 360 degrees to allows hose to be pulled in any direction & Also to prevent Hose Damage etc., complete, as per the instructions of Architect/Landscape Architect/Engineer In Charge.

Supply of 3.0" Twin Disc Filter 50 M³ / Hr. including installation charges. (brands like Rain Bird or equivalent)

Supply,Fixing & commissioning of Monobloc pumpset of having discharge and head of design flow , UPVC sch 40 - suction & delivery manifold and mounted on a baseframe with proper supports etc., complete, as per the instructions of Architect/Landscape Architect/Engineer In Charge. Duty of Pump : 3.5 LPS Pressure Head Range = 50 - 55 Mtr No. of Pumps : 1 Working + 0 Standby

Supply ,Fixing & Commissioning of Control Cable for Pump Set - 3 core X 4 Sq.mm Copper

Supply,Fixing & commissioning of 3'' control Valve, Butterfly Valve VAN Stone flange & Tail Piece in mainline for bypass and flow diversion of approved quality with pressure rating of PN 10 etc., complete, as per the instructions of Architect/Landscape Architect/Engineer In Charge.

Supply,Fixing & commissioning of 2.5'' control Valve, Butterfly Valve VAN Stone flange & Tail Piece in mainline for bypass and flow diversion of approved quality with pressure rating of PN 10 etc., complete, as per the instructions of Architect/Landscape Architect/Engineer In Charge.

Supply of Gunmetal non return valve 3.0 " dia. (ISI)

Supply,Fixing & commissioning of Pressure release valve 3" with pressure setting from 0 to 7 Bar etc., complete, as per the instructions of Architect/Landscape Architect/Engineer In Charge.

Supply and Erection of cubicle type floor mounting type made out of 16 Gauge CRCA sheet steel construction dust and vermin proof for indoor use, extensible of both sides rated for 433V, 3 phase 50 Hz AC supply 4 wire system comprising of the following as per the detail specification. (Construction as per Technical specification). The painting of the complete system will be powder coated (The colour as per the choice Architect) or as per the requirement of the employer. All outgoing feeders will be connected with 1.1 KV grade PVC armoured cable. So bus bar will be extended for easy termination and suitable removal type gland plate will be provided for each feeders. LSB – 1 to 3 (OUTDOOR TYPE)

Supply and Erection of board will be fabricated out of 16 gauge CR sheet with necessary ‘L’ angle support frame using 11/2” x 1/4” ‘L’ angle. 3 PHASE LDB – 1 to 6 [ OUTDOOR TYPE ]

Supply,Fixing & Commissioning of Direct burial 14 Awg x 2 Maxi cable with PVC insulated UL stndard 493 with impregnated polyethene jacket and soft annealed tin coated copper confirming to ASTM B-33 for two way communication between decoder controller and decoders complete

Supply,Fixing & Commissioning of PVC pipe 25mm-10 kg/cm² including fittings and accessories

Supply,Fixing & commissioning Of Two wire control system ESP-LX IVM having solenoid and decoder in one unit as interface & Maximum Two Wire Connectors Between Communication Cable and Solenoid Valve,supports up to 60 stations standard Up to four 2-Wire paths, plus flow sensing and advanced flow management tools. supports upto 5 flow sensor inputs and removable front panel is programmable under battery power. water management features like: • Learn Flow utility and fl ow usage totalizer help optimize water usage, • FloWatch™ protection for high and low flow conditions , FloManager™ manages hydraulic demand, make full use of available water to turn on as many stations as possible without exceeding water supply and reducing the total time to complete irrigation cycles. SimulStations™ allows stations to operate at the same time; up to 8 with LX-IVM • Cycle+Soak™ by station, • Rain Delay up to 30 days, • 365-Day Calendar Day Off (up to 5 days), • Station Delay by program, • Normally Open or Normally Closed Master, Valves programmable by station; up to 5 with LX-IVM • Optional Weather Sensors are programmable by station to prevent or pause watering; up to 4 with LX-IVM. • Station Run Time: 0 min. to 96 hrs. • Seasonal Adjust: 0% to 300% (96 hrs. maximum station run time), • 10 independent programs on the ESP-LXI IVM • 8 start times per program,• Program Day Cycles include Custom days of the week, Odd, Odd no 31st, Even, and Cyclical dates,•

Supply,Fixing & Commissioning of IVM-SOL Interfaces (solenoid and decoder in one unit as interface with facility of Maximum Two Wire Connector Between the Solenoid valve & Communication Cable) with LX-IVM to control station valves and master valves as per specifications complete

Supply,Fixing & Commissioning of IVM-OUT Interfaces with LX-IVM to manage 3rd party valves and external gear such as pump stations as per specifications complete

Supply,Fixing & Commissioning of IVM-SD for surge protection on the 2-Wire path as required with copper grounding rod, clamps, charcoal and all requisite accessories as per specifications complete

Supply,Fixing & commissioning of 1" Solenoid globe angle inlet Valves with provision to DC Latched interface module, fabric reinforced Nitrile diaphram Material and rugged PVC construction ,compatible and slow closing to prevent water hammer,pressure rating upto 10.4 KSC and maximum flow of 40GPM ,max water temp. upto 42degree centigrade, 9V DC solenoid ( IVM-SOL Interfaces ) Without AC Coil ,current rating 0.41A @50Hz,coil resistance 30ohm with provision to attach PRS-Dial PGA Pressure Regulation Optional PRS-D

Supply,Fixing & commissioning of 1.5" Solenoid globe angle inlet Valves with provision to DC Latched interface module, fabric reinforced Nitrile diaphram Material and rugged PVC construction ,compatible and slow closing to prevent water hammer,pressure rating upto 10.4 KSC and maximum flow of 100GPM ,max water temp. upto 42degree centigrade, 9V DC solenoid ( IVM-SOL Interfaces) Without AC Coil ,current rating 0.41A @50Hz,coil resistance 30ohm with provision to attach PRS-Dial PGA Pressure Regulation Optional PRS-D

Supply,Fixing & commissioning of 2" Solenoid globe angle inlet Valves with provision to DC Latched interface module, fabric reinforced Nitrile diaphram Material and rugged PVC durable glass -filled nylon construction ,compatible with and slow closing to prevent water hammer,pressure rating upto 10.4 KSC and maximum flow of 150GPM ,max water temp. upto 42degree centigrade, 9V DC solenoid ( IVM-SOL Interfaces ) , Without AC Coil current rating 0.41A @50Hz,coil resistance 30ohm with provision to attach PRS-Dial PGA Pressure Regulation Optional PRS-D

Supply,Fixing & commissioning of PRS-DIAL to Maintain constant outlet pressure between 1.04 to6.9 KSC

Supply,Fixing & commissioning of direct bury -on wire connector with strain relief ,UL486 D certified ,with waterproof silicon sealant ,fits wire from 22ga to6 ga as per specifications complete DBRY

Supply,Fixing & commissioning of automatic rain shut off device ,latching hinge with multiple rainfall settings 5mm to 20mm UL CUL listed and CE approved complete RSD BEX

Supply,Fixing & commissioning of 9VDC Relay & 9V DC Coil With Stabilizer 300watts

Supply & Laying of 3" dia PVC with minimum thickness of 3mm with all its accessories required.

Supply and Fixing of PVC Junction Box waterproof suitable above Pipe

Supply & Erection of 200mm Dia Hume Pipe for road crossings etc. as per Site Requirement for Electrical

Supply & stacking of red earth at site to the departmental guage for pre-measurements which is of light textured, crystalline, porous and friable and not of generally acidic or neutral but not of alkaline and should be fertile, including seignior age charges, cost of transportation, loading, unloading, stacking and inclusive of all taxes etc., complete.

Supply and filling with earthup to 30Km for foundation basment etc, includading watering and consolidating etc, complete

Supply of well decomposed Farm yard Manure in a powdery form, devoid of soil sand, stones, plastics and other materials, highly nutrient and which supports plant growth.

Mixing charges of Red soil, sand and manure uniformly (1:1:1) for Preparation of soil mixture (excluding material cost)

Spreading of red soil, gravel or sand including watering and rolling which hand roller for every 75 mm thickness - including hire charges of roller.

Planting of Canna indica varigated Plant foliage shrub variety of height 30-45 cm in polythene bag of size 6x8 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Clerodendron green / variegated Plant ornamental foliage shrub variety of height 30-45 cm in polythene bag of size 6x8 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site incharge.

Planting of Duranta new gold Plant ornamental foliage shrub variety of height 30-45 cm in polythene bag of size 6x8 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Euphorbia milli foliage shrub variety of height 30-45 cm in polythene bag of size 6x8 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Ficus black ornamental foliage shrub variety of height 30-45 cm in polythene bag of size 6x8 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Ficus ponda ornamental foliage shrub variety of height 30-45 cm in polythene bag of size 6x8 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Ficus starlight ornamental foliage shrub variety of height 30-45 cm in polythene bag of size 6x8 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Galphimia Plant foliage shrub variety of height 30-45 cm in polythene bag of size 6x8 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge

Planting of Bamboo grass ornamental foliage shrub variety of height 30-45 cm in polythene bag of size 6x8 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Bougainvilla foliage shrub variety of height 30-45 cm in polythene bag of size 6x8 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Heliconium foliage shrub variety of height 30-45 cm in polythene bag of size 6x8 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Hibiscus hawai foliage shrub variety of height 30-45 cm in polythene bag of size 6x8 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Ixora dwarf varieties foliage shrub variety of height 30-45 cm in polythene bag of size 6x8 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Jasmine Plant foliage shrub variety of height 30-45 cm in polythene bag of size 6x8 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Jetropha Plant foliage shrub variety of height 30-45 cm in polythene bag of size 6x8 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Lavender Plant ornamental foliage shrub variety of height 30-45 cm in polythene bag of size 6x8 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Lilly foliage shrub variety of height 30- 45 cm in polythene bag of size 6x8 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in- charge.

Planting of Nerium oleander dwarf foliage shrub variety of height 30-45 cm in polythene bag of size 6x8 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Pachystachys lutea -Lollipop plant ornamental foliage shrub variety of height 30-45 cm in polythene bag of size 6x8 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Purple Fountain Grass – Pennisetum setaceum 'Cupreum' foliage shrub variety of height 30-45 cm in polythene bag of size 6x8 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Tecoma goudi choudi foliage shrub variety of height 30-45 cm in polythene bag of size 6x8 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Tecoma capensis foliage shrub variety of height 30-45 cm in polythene bag of size 6x8 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Alternanthera varigated ornamental foliage Ground cover variety in polythene bag of dia 20 cm including loading and unloading charges, transportation, stacking of sapling at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Chlorophytum ornamental foliage Ground cover variety in polythene bag of dia 20 cm including loading and unloading charges, transportation, stacking of sapling at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Hemigraphis ornamental foliage Ground cover variety in polythene bag of dia 20 cm including loading and unloading charges, transportation, stacking of sapling at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Ipomea ornamental foliage Ground cover variety in polythene bag of dia 20 cm including loading and unloading charges, transportation, stacking of sapling at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in- charge.

Planting of Lantana foliage Ground cover variety in polythene bag of dia 20 cm including loading and unloading charges, transportation, stacking of sapling at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Ophiopogon ornamental foliage Ground cover variety in polythene bag of dia 20 cm including loading and unloading charges, transportation, stacking of sapling at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Syngonium foliage Ground cover variety in polythene bag of dia 20 cm including loading and unloading charges, transportation, stacking of sapling at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in- charge.

Planting of Wedelia trilobata foliage Ground cover variety in polythene bag of dia 20 cm including loading and unloading charges, transportation, stacking of sapling at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in- charge.

Planting of Calliandra foliage Specimen plant variety of height 105- 120 cm in polythene bag of size 16x16 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge

Planting of Ficus benjamina green ornamental foliage Specimen plant variety of height 105-120 cm in polythene bag of size 16x16 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in- charge.

Planting of Juniperous ornamental foliage Specimen plant variety of height 105-120 cm in polythene bag of size 16x16 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Plumaria Dwarf ornamental foliage Specimen plant variety of height 105- 120 cm in polythene bag of size 16x16 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Thuja ornamental foliage Specimen plant/ Thespesia populnea/ Dichrosanchys clnerea/ memcylon umbellatum plants variety of height 105-120 cm in polythene bag of size 16x16 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Lemon grass Herbal plant variety of height 20-25 cm in polythene bag of size 6x7 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Cynodon dactylon (Arugampul) Grass including necessary soil preparation, transportation, loading and unloading charges etc., as directed by the site in-charge.

Supply,Fixing & commissioning of 3/4th inch Hose Swivel Made up of Solid Brass Swivels up to 360 degrees to allows hose to be pulled in any direction & Also to prevent Hose Damage etc., complete, as per the instructions of Architect/Landscape Architect/Engineer In Charge.

Supply,Fixing & commissioning of Pressure release valve 3" with pressure setting from 0 to 7 Bar etc., complete, as per the instructions of Architect/Landscape Architect/Engineer In Charge.

Submission of Shop drawing, As built drawing, Handing over documents, Training for maintenance team after commissioning of the system

Supplying and Planting of Tabebuia rosea tree sapling of height 180 - 240 cm in polythene bag of size 15x16 inch including supporting stack of 5 cm dia casurina pole of 10 feet height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site incharge.

Supplying and Planting of Bauhinia purpurea tree sapling of height 240 – 300 cm in polythene bag of size 20x21 inch including supporting stack of 5 cm dia casurina pole of 10 feet height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge

Supplying and Planting of Calophyllum inophyllum tree sapling of height 240 – 300 cm in polythene bag of size 20x21 inch including supporting stack of 5 cm dia casurina pole of 10 feet height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site incharge.

Supplying and Planting of Peltophorum tree sapling of height 240 – 300 cm in polythene bag of size 20x21 inch including supporting stack of 5 cm dia casurina pole of 10 feet height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Supplying and Planting of Cocoloba Unifera tree/Butea monosperma sapling of height 180 - 240 cm in polythene bag of size 15x16 inch including supporting stack of 5 cm dia casurina pole of 10 feet height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in- charge.

Supplying and Planting of Plumeria tree sapling of height 240 – 300 cm in polythene bag of size 20x21 inch including supporting stack of 5 cm dia casurina pole of 10 feet height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge

Supplying and Planting of Cassia fistula tree sapling of height 180 - 240 cm in polythene bag of size 15x16 inch including supporting stack of 5 cm dia casurina pole of 10 feet height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in- charge.

Supplying and Planting of Cordia sebestena/ Dalbergia tree sapling of height 180 - 240 cm in polythene bag of size 15x16 inch including supporting stack of 5 cm dia casurina pole of 10 feet height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in- charge.

Supplying and Planting of Erythrina tree sapling of height 180 - 240 cm in polythene bag of size 15x16 inch including supporting stack of 5 cm dia casurina pole of 10 feet height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Supplying and Planting of Kigelia pinnata tree sapling of height 180 - 240 cm in polythene bag of size 15x16 inch including supporting stack of 5 cm dia casurina pole of 10 feet height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in- charge.

Supplying and Planting of Lagerstroemia tree/ dichrostachys cinerea tree sapling of height 180 - 240 cm in polythene bag of size 15x16 inch including supporting stack of 5 cm dia casurina pole of 10 feet height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in- charge.

Supplying and Planting of Mimusops elengi /Poovarasu tree /Saraca indica /Michelia champaka (Shenbagam) tree/madhuca longifolia sapling of height 180 - 240 cm in polythene bag of size 15x16 inch including supporting stack of 5 cm dia casurina pole of 10 feet height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in- charge.

Supplying and Planting of Pungam tree sapling of height 180 - 240 cm in polythene bag of size 15x16 inch including supporting stack of 5 cm dia casurina pole of 10 feet height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Supplying and Planting of Spathodea campanulata tree /Swietenia macrophylla/ Schleichera oleosa/ shorea robusya tree sapling of height 180 - 240 cm in polythene bag of size 15x16 inch including supporting stack of 5 cm dia casurina pole of 10 feet height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in- charge.

Supplying and Planting of Tabebuia rosea tree / Tabebuia argentea sapling of height 180 - 240 cm in polythene bag of size 15x16 inch including supporting stack of 5 cm dia casurina pole of 10 feet height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in- charge.

Supplying and Planting of Bauhinia purpurea tree/ Thespesia populnea sapling of height 240 – 300 cm in polythene bag of size 20x21 inch including supporting stack of 5 cm dia casurina pole of 10 feet height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Supplying and Planting of Michelia champaka (Shenbagam) tree sapling of height 240 – 300 cm in polythene bag of size 20x21 inch including supporting stack of 5 cm dia casurina pole of 10 feet height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Supplying and Planting of Bamboo grass variegeta tree sapling of height 300 - 360 cm in polythene bag of size 15x16 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Supplying and Planting of Budha Belly Bamboo tree sapling of height 300 - 360 cm in polythene bag of size 15x16 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Supplying and Planting of Bismarckia palm variety of height 180-210 cm in polythene bag of size 16x16 inch including supporting stack of 5cm dia casurina pole of 10' height including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Supplying and Planting of Topiary for various shapes and sizes of 4ft to 5ft in Pot of dia 45 cm including loading and unloading charges, transportation, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the sitein- charge.

Preparation of Mounds of various size and shape by availlable excavated/ Supplied earth in layers not exceeding 20 cm in depth, breaking clods, watering of each layer, dressing etc., lead upto 50 meter and lift upto 1.5 m complete as per direction of Officer - in - charge.

Supply and Erection of cubicle type floor mounting type made out of 16 Gauge CRCA sheet steel construction dust and vermin proof for indoor use, extensible of both sides rated for 433V, 3 phase 50 Hz AC supply 4 wire system comprising of the following as per the detail specification. (Construction as per Technical specification). The painting of the complete system will be powder coated (The colour as per the choice Architect) or as per the requirement of the employer. All outgoing feeders will be connected with 1.1 KV grade PVC armoured cable. So bus bar will be extended for easy termination and suitable removal type gland plate will be provided for each feeders. LSB – 1 (OUTDOOR TYPE) INCOMING : 160A TPN FSU with fuse links – 1 No. OUTGOING : 63A TPN FSU with fuse links - 3 nos. Incoming metering:- Incoming metering will have 1 No digital type 96sq mm 1No multiparameter Class:1 accuracy RYB indication lamps necessary CT’s and control MCB's etc,. - 1 Set. Bus Bar Size: 1” x 1/4” Cu flat 1 Run / Phase. 1” x 1/8" Cu. Flat 1 Run / Neutral . EARTHING : 1” x 1/8” Cu Flat. Paint: Powder Coating Process. NOTE: “L” Angle Frame support will be provided for above said panel using 11/2” x 1/4” “L” Angle with enamel coating paint and its necessary hardware etc. Frame height will be 350mm

LSB – 2 to 6 (OUTDOOR TYPE) INCOMING : 160A TPN FSU with fuse links – 1 No. OUTGOING : 63A TPN FSU with fuse links - 4 nos. Incoming metering:- Incoming metering will have 1 No digital type 96sq mm 1No multiparameter Class:1 accuracy RYB indication lamps necessary CT’s and control MCB's etc,. - 1 Set. Bus Bar Size: 1” x 1/4” Cu flat 1 Run / Phase. 1” x 1/8" Cu. Flat 1 Run / Neutral . EARTHING : 1” x 1/8” Cu Flat. Paint: Powder Coating Process. NOTE: “L” Angle Frame support will be provided for above said panel using 11/2” x 1/4” “L” Angle with enamel coating paint and its necessary hardware etc. Frame height will be 350mm

SUPPLY OF NERI ARCHITECTURAL DIFFERENTIAL TWIN ARM(SHELIAK DESIGN) POLE - JM.02.23.052 - 6.5M height Differential Twin arm Pole Made in combination of mild steel pipe sections 114mm,89mm & 60mm dia. Top Sheilak design bracket made in combination of mild steel pipe sections 60mm dia.(vertical),33mm dia.(horizontal) & Decorative part with design leafs as shown in the diagram, made of cast iron in single piece (weight 9kgs.), to get 750mm horizonal arm length & pleasing aesthetics. Arch. Base design starts with 322mm Dia. ring , radially tapers to 215mm for a height of 70mm, which is followed by a ring of 215mm dia,, then radially tapers to 135mm for a height of 115mm .Total weight of the base is 15 Kgs. & height of the base is 235mm. Decorative Ring-1 (114mm/89mm-4.08kgs.) & Ring-2 (89mm/60mm-2.55kgs.)are made of cast iron. Decorative cast iron pole top starts from bottom with a ring section of dia. 67mm followed by a ring of dia. 75mm, radially increases to 100mm dia. for a height 15mm,then radially reduces to 46mm for a height 20mm followed by a jack shaped section(45mm(W & 20mm(H), followed by a ring of dia. 60mm which is followed by a Conical section(bottom dia. 40mm & top dia.10mm,140mm(H) with sphere shape(30mm dia.) on top-total height of the pole top is 260mm & weight is 2.5 Kgs. All cast iron weights mentioned are with +/-5% tolerance.The pole to be provided with suitable size base plate. This base plate along with foundation bolts of suitable size to be used for ensuring firm grouting into the specially designed RCC foundation.Entire pole shall be made to provide pleasing aesthetics as approved by Concerned Engineer in-charge. After Fabrication, Entire Pole is hot dip galvanized (60 microns Min) for the effective corrosion resistance . The hot dip Galvanised pole should be provided with an inbuilt junction box to fix 32A connectors and 6A MCB, at the bottom - the inbuilt box should have a flush door of suitable size. wind pressure calculation as per IS 875(part-3) & structural calculation report as per EN40 should be submitted to verify the pole design. Pole & it's parts are painted in 3 layer coating(coating thickness-100 microns minimum) in which 1st layer with etch primer, 2nd layer with epoxy primer & 3rd final layer with PU paint - customised colour Metallaic Grey.SUPPLY OF NERI ARCHITECTURAL DIFFERENTIAL TWIN ARM(SHELIAK DESIGN) POLE - JM.02.23.052 - 6.5M height Differential Twin arm Pole Made in combination of mild steel pipe sections 114mm,89mm & 60mm dia. Top Sheilak design bracket made in combination of mild steel pipe sections 60mm dia.(vertical),33mm dia.(horizontal) & Decorative part with design leafs as shown in the diagram, made of cast iron in single piece (weight 9kgs.), to get 750mm horizonal arm length & pleasing aesthetics. Arch. Base design starts with 322mm Dia. ring , radially tapers to 215mm for a height of 70mm, which is followed by a ring of 215mm dia,, then radially tapers to 135mm for a height of 115mm .Total weight of the base is 15 Kgs. & height of the base is 235mm. Decorative Ring-1 (114mm/89mm-4.08kgs.) & Ring-2 (89mm/60mm-2.55kgs.)are made of cast iron. Decorative cast iron pole top starts from bottom with a ring section of dia. 67mm followed by a ring of dia. 75mm, radially increases to 100mm dia. for a height 15mm,then radially reduces to 46mm for a height 20mm followed by a jack shaped section(45mm(W & 20mm(H), followed by a ring of dia. 60mm which is followed by a Conical section(bottom dia. 40mm & top dia.10mm,140mm(H) with sphere shape(30mm dia.) on top-total height of the pole top is 260mm & weight is 2.5 Kgs. All cast iron weights mentioned are with +/-5% tolerance.The pole to be provided with suitable size base plate. This base plate along with foundation bolts of suitable size to be used for ensuring firm grouting into the specially designed RCC foundation.Entire pole shall be made to provide pleasing aesthetics as approved by Concerned Engineer in-charge. After Fabrication, Entire Pole is hot dip galvanized (60 microns Min) for the effective corrosion resistance . The hot dip Galvanised pole should be provided with an inbuilt junction box to fix 32A connectors and 6A MCB, at the bottom - the inbuilt box should have a flush door of suitable size. wind pressure calculation as per IS 875(part-3) & structural calculation report as per EN40 should be submitted to verify the pole design. Pole & it's parts are painted in 3 layer coating(coating thickness-100 microns minimum) in which 1st layer with etch primer, 2nd layer with epoxy primer & 3rd final layer with PU paint - customised colour Metallaic Grey.

SUPPLYOF NERI ARCHITECTURAL LED LIGHT FIXTURE MODEL - LIGHT 21 (60W-70W) Power Module LED, 4000K, Suspended Type - Light 21: Upper frame with threaded coupling G3/4" for suspended mounting. at the top, made of die cast aluminum using pressure die-casting process. in single piece. Lower frame composed by a ring made of die cast aluminum using pressure die-casting process in single piece. Auxiliary and optical compartment can be accessed by opening the frames. Company /brand name should be engraved in the mold of the body. Drop shaped screen in polymethylmethacrylate (PMMA), transparent made in single piece using injection moulding process. Silicone gasket between the upper and lower frames. Finish-Pure polyester powder coating in Grey Colour.optical compartment IP Rating - IP 66. Height – 545mm,Diameter - 550mm,Weight - 8Kgs., Power LED Module with Company /brand name printed on PCB with the metal core plate.LED Chips of CREE/NICHIA/OSRAM/LUMILEDS make - same should be supported by LED manufacturer's tech sheet . Colour Rendering Index: Ra > 70. Electronic Power Supply for LED Module, which offers Protection against Short Circuit, Over- Voltage & Over- Current, with in-built surge protection (an additional surge protection device of 10kV also provided in-built the fixture). Optics with refractive lens in PMMA which should offer all the Type II,III,IV & V distribtuions. LED Lifetime @L90 >1,00,000hours@Ts 85°C. LM80 report from LED Manufacturer should be submitted. Safety test report as per IEC 60598 from UL/UL authorised/Intertek. LM79 report also should be submitted from UL/UL Authorised/Intertek Laboratory. Sample should be submitted for approval from concerned engineer-in charge.SUPPLYOF NERI ARCHITECTURAL LED LIGHT FIXTURE MODEL - LIGHT 21 (60W-70W) Power Module LED, 4000K, Suspended Type - Light 21: Upper frame with threaded coupling G3/4" for suspended mounting. at the top, made of die cast aluminum using pressure die-casting process. in single piece. Lower frame composed by a ring made of die cast aluminum using pressure die-casting process in single piece. Auxiliary and optical compartment can be accessed by opening the frames. Company /brand name should be engraved in the mold of the body. Drop shaped screen in polymethylmethacrylate (PMMA), transparent made in single piece using injection moulding process. Silicone gasket between the upper and lower frames. Finish-Pure polyester powder coating in Grey Colour.optical compartment IP Rating - IP 66. Height – 545mm,Diameter - 550mm,Weight - 8Kgs., Power LED Module with Company /brand name printed on PCB with the metal core plate.LED Chips of CREE/NICHIA/OSRAM/LUMILEDS make - same should be supported by LED manufacturer's tech sheet . Colour Rendering Index: Ra > 70. Electronic Power Supply for LED Module, which offers Protection against Short Circuit, Over- Voltage & Over- Current, with in-built surge protection (an additional surge protection device of 10kV also provided in-built the fixture). Optics with refractive lens in PMMA which should offer all the Type II,III,IV & V distribtuions. LED Lifetime @L90 >1,00,000hours@Ts 85°C. LM80 report from LED Manufacturer should be submitted. Safety test report as per IEC 60598 from UL/UL authorised/Intertek. LM79 report also should be submitted from UL/UL Authorised/Intertek Laboratory. Sample should be submitted for approval from concerned engineer-in charge.

SUPPLYOF NERI ARCHITECTURAL LED LIGHT FIXTURE MODEL - LIGHT 21 (30W-40W) Power Module LED, 4000K, Suspended Type - Light 21: Upper frame with threaded coupling G3/4" for suspended mounting. at the top, made of die cast aluminum using pressure die-casting process. in single piece. Lower frame composed by a ring made of die cast aluminum using pressure die-casting process in single piece. Auxiliary and optical compartment can be accessed by opening the frames. Company /brand name should be engraved in the mold of the body. Drop shaped screen in polymethylmethacrylate (PMMA), transparent made in single piece using injection moulding process. Silicone gasket between the upper and lower frames. Finish-Pure polyester powder coating in Grey Colour.optical compartment IP Rating - IP 66.. Height – 545mm,Diameter - 550mm,Weight - 8Kgs.,. Power LED Module with Company /brand name printed on PCB with the metal core plate.LED Chips of CREE/NICHIA/OSRAM/LUMILEDS make - same should be supported by LED manufacturer's tech sheet . Colour Rendering Index: Ra > 70. Electronic Power Supply for LED Module, which offers Protection against Short Circuit, Over- Voltage & Over- Current, with in-built surge protection (an additional surge protection device of 10kV also provided in-built the fixture). Optics with refractive lens in PMMA which should offer all the Type II,III,IV & V distribtuions. LED Lifetime @L90 >1,00,000hours@Ts 85°C. LM80 report from LED Manufacturer should be submitted. Safety test report as per IEC 60598 from UL/UL authorised/Intertek. LM79 report also should be submitted from UL/UL Authorised/Intertek Laboratory. Sample should be submitted for approval from concerned engineer-in charge.SUPPLYOF NERI ARCHITECTURAL LED LIGHT FIXTURE MODEL - LIGHT 21 (30W-40W) Power Module LED, 4000K, Suspended Type - Light 21: Upper frame with threaded coupling G3/4" for suspended mounting. at the top, made of die cast aluminum using pressure die-casting process. in single piece. Lower frame composed by a ring made of die cast aluminum using pressure die-casting process in single piece. Auxiliary and optical compartment can be accessed by opening the frames. Company /brand name should be engraved in the mold of the body. Drop shaped screen in polymethylmethacrylate (PMMA), transparent made in single piece using injection moulding process. Silicone gasket between the upper and lower frames. Finish-Pure polyester powder coating in Grey Colour.optical compartment IP Rating - IP 66.. Height – 545mm,Diameter - 550mm,Weight - 8Kgs.,. Power LED Module with Company /brand name printed on PCB with the metal core plate.LED Chips of CREE/NICHIA/OSRAM/LUMILEDS make - same should be supported by LED manufacturer's tech sheet . Colour Rendering Index: Ra > 70. Electronic Power Supply for LED Module, which offers Protection against Short Circuit, Over- Voltage & Over- Current, with in-built surge protection (an additional surge protection device of 10kV also provided in-built the fixture). Optics with refractive lens in PMMA which should offer all the Type II,III,IV & V distribtuions. LED Lifetime @L90 >1,00,000hours@Ts 85°C. LM80 report from LED Manufacturer should be submitted. Safety test report as per IEC 60598 from UL/UL authorised/Intertek. LM79 report also should be submitted from UL/UL Authorised/Intertek Laboratory. Sample should be submitted for approval from concerned engineer-in charge.

SUPPLY OF NERI ARCHITECTURAL SINGLE ARM(SHELIAK DESIGN) POLE - JM.02.23.051 - 6.5M height single arm Pole Made in combination of mild steel pipe sections 114mm,89mm & 60mm dia. Top Sheilak design bracket made in combination of mild steel pipe sections 60mm dia.(vertical),33mm dia.(horizontal) & Decorative part with design leafs as shown in the diagram, made of cast iron in single piece (weight 9kgs.), to get 750mm horizonal arm length & pleasing aesthetics. Arch. Base design starts with 322mm Dia. ring , radially tapers to 215mm for a height of 70mm, which is followed by a ring of 215mm dia,, then radially tapers to 135mm for a height of 115mm .Total weight of the base is 15 Kgs. & height of the base is 235mm. Decorative Ring-1 (114mm/89mm-4.08kgs.) & Ring-2 (89mm/60mm-2.55kgs.)are made of cast iron. Decorative cast iron pole top starts from bottom with a ring section of dia. 67mm followed by a ring of dia. 75mm, radially increases to 100mm dia. for a height 15mm,then radially reduces to 46mm for a height 20mm followed by a jack shaped section(45mm(W & 20mm(H), followed by a ring of dia. 60mm which is followed by a Conical section(bottom dia. 40mm & top dia.10mm,140mm(H) with sphere shape(30mm dia.) on top-total height of the pole top is 260mm & weight is 2.5 Kgs. All cast iron weights mentioned are with +/-5% tolerance.The pole to be provided with suitable size base plate. This base plate along with foundation bolts of suitable size to be used for ensuring firm grouting into the specially designed RCC foundation.Entire pole shall be made to provide pleasing aesthetics as approved by Concerned Engineer in-charge. After Fabrication, Entire Pole is hot dip galvanized (60 microns Min) for the effective corrosion resistance . The hot dip Galvanised pole should be provided with an inbuilt junction box to fix 32A connectors and 6A MCB, at the bottom - the inbuilt box should have a flush door of suitable size. wind pressure calculation as per IS 875(part-3) & structural calculation report as per EN40 should be submitted to verify the pole design. Pole & it's parts are painted in 3 layer coating(coating thickness-100 microns minimum) in which 1st layer with etch primer, 2nd layer with epoxy primer & 3rd final layer with PU paint - customised colour Metallaic Grey. SUPPLY OF NERI ARCHITECTURAL SINGLE ARM(SHELIAK DESIGN) POLE - JM.02.23.051 - 6.5M height single arm Pole Made in combination of mild steel pipe sections 114mm,89mm & 60mm dia. Top Sheilak design bracket made in combination of mild steel pipe sections 60mm dia.(vertical),33mm dia.(horizontal) & Decorative part with design leafs as shown in the diagram, made of cast iron in single piece (weight 9kgs.), to get 750mm horizonal arm length & pleasing aesthetics. Arch. Base design starts with 322mm Dia. ring , radially tapers to 215mm for a height of 70mm, which is followed by a ring of 215mm dia,, then radially tapers to 135mm for a height of 115mm .Total weight of the base is 15 Kgs. & height of the base is 235mm. Decorative Ring-1 (114mm/89mm-4.08kgs.) & Ring-2 (89mm/60mm-2.55kgs.)are made of cast iron. Decorative cast iron pole top starts from bottom with a ring section of dia. 67mm followed by a ring of dia. 75mm, radially increases to 100mm dia. for a height 15mm,then radially reduces to 46mm for a height 20mm followed by a jack shaped section(45mm(W & 20mm(H), followed by a ring of dia. 60mm which is followed by a Conical section(bottom dia. 40mm & top dia.10mm,140mm(H) with sphere shape(30mm dia.) on top-total height of the pole top is 260mm & weight is 2.5 Kgs. All cast iron weights mentioned are with +/-5% tolerance.The pole to be provided with suitable size base plate. This base plate along with foundation bolts of suitable size to be used for ensuring firm grouting into the specially designed RCC foundation.Entire pole shall be made to provide pleasing aesthetics as approved by Concerned Engineer in-charge. After Fabrication, Entire Pole is hot dip galvanized (60 microns Min) for the effective corrosion resistance . The hot dip Galvanised pole should be provided with an inbuilt junction box to fix 32A connectors and 6A MCB, at the bottom - the inbuilt box should have a flush door of suitable size. wind pressure calculation as per IS 875(part-3) & structural calculation report as per EN40 should be submitted to verify the pole design. Pole & it's parts are painted in 3 layer coating(coating thickness-100 microns minimum) in which 1st layer with etch primer, 2nd layer with epoxy primer & 3rd final layer with PU paint - customised colour Metallaic Grey.

SUPPLYOF NERI ARCHITECTURAL LED LIGHT FIXTURE MODEL - LIGHT 21 (60W-70W) Power Module LED, 4000K, Suspended Type - Light 21: Upper frame with threaded coupling G3/4" for suspended mounting. at the top, made of die cast aluminum using pressure die-casting process. in single piece. Lower frame composed by a ring made of die cast aluminum using pressure die-casting process in single piece. Auxiliary and optical compartment can be accessed by opening the frames. Company /brand name should be engraved in the mold of the body. Drop shaped screen in polymethylmethacrylate (PMMA), transparent made in single piece using injection moulding process. Silicone gasket between the upper and lower frames. Finish-Pure polyester powder coating in Grey Colour.optical compartment IP Rating - IP 66. Height – 545mm,Diameter - 550mm,Weight - 8Kgs., Power LED Module with Company /brand name printed on PCB with the metal core plate.LED Chips of CREE/NICHIA/OSRAM/LUMILEDS make - same should be supported by LED manufacturer's tech sheet . Colour Rendering Index: Ra > 70. Electronic Power Supply for LED Module, which offers Protection against Short Circuit, Over- Voltage & Over- Current, with in-built surge protection (an additional surge protection device of 10kV also provided in-built the fixture). Optics with refractive lens in PMMA which should offer all the Type II,III,IV & V distribtuions. LED Lifetime @L90 >1,00,000hours@Ts 85°C. LM80 report from LED Manufacturer should be submitted. Safety test report as per IEC 60598 from UL/UL authorised/Intertek. LM79 report also should be submitted from UL/UL Authorised/Intertek Laboratory. Sample should be submitted for approval from concerned engineer-in charge.SUPPLYOF NERI ARCHITECTURAL LED LIGHT FIXTURE MODEL - LIGHT 21 (60W-70W) Power Module LED, 4000K, Suspended Type - Light 21: Upper frame with threaded coupling G3/4" for suspended mounting. at the top, made of die cast aluminum using pressure die-casting process. in single piece. Lower frame composed by a ring made of die cast aluminum using pressure die-casting process in single piece. Auxiliary and optical compartment can be accessed by opening the frames. Company /brand name should be engraved in the mold of the body. Drop shaped screen in polymethylmethacrylate (PMMA), transparent made in single piece using injection moulding process. Silicone gasket between the upper and lower frames. Finish-Pure polyester powder coating in Grey Colour.optical compartment IP Rating - IP 66. Height – 545mm,Diameter - 550mm,Weight - 8Kgs., Power LED Module with Company /brand name printed on PCB with the metal core plate.LED Chips of CREE/NICHIA/OSRAM/LUMILEDS make - same should be supported by LED manufacturer's tech sheet . Colour Rendering Index: Ra > 70. Electronic Power Supply for LED Module, which offers Protection against Short Circuit, Over- Voltage & Over- Current, with in-built surge protection (an additional surge protection device of 10kV also provided in-built the fixture). Optics with refractive lens in PMMA which should offer all the Type II,III,IV & V distribtuions. LED Lifetime @L90 >1,00,000hours@Ts 85°C. LM80 report from LED Manufacturer should be submitted. Safety test report as per IEC 60598 from UL/UL authorised/Intertek. LM79 report also should be submitted from UL/UL Authorised/Intertek Laboratory. Sample should be submitted for approval from concerned engineer-in charge.

SUPPLY OF NERI ARCHITECTURAL POST TOP POLE - JM.02.23.053 - 3.5M height post top Pole Made of hot dip galvanised mild steel pipe sections 114mm dia. & 76mm dia. Arch. Base design starts with 322mm Dia. ring , radially tapers to 215mm for a height of 70mm, which is followed by a ring of 215mm dia,, then radially tapers to 135mm for a height of 115mm .Total weight of the base is 15 Kgs. & height of the base is 235mm . Ring-1(114mm/76mm, weight- 4kgs.) & Top Ring-(weight- 3kgs.) are made of cast iron. Entire pole & Bracket including all the cast iron elements shall be made to provide pleasing aesthetics as approved by Concerned Engineer in-charge. After Fabrication, Entire Pole is hot dip galvanized(60 microns Minimum ) for the effective corrosion resistance. The hot dip Galvanised pole should be provided with an inbuilt junction box to fix 32A connectors and 6A MCB, at the bottom - the inbuilt box should have a flush door of suitable size. The pole to be provide with suitable size base plate. This base plate along with foundation bolts of suitable size to be used for ensuring firm grouting into the specially designed RCC foundation. wind pressure calculation as per IS 875(part-3) & structural calculation report as per EN40 should be submitted to verify the pole design. Pole & Cast iron parts are painted in 3 layer coating(coating thickness-100 microns minimum) in which 1st layer with etch primer, 2nd layer with epoxy primer & 3rd final layer with PU paint - customised colour Metallaic NERI Grey.SUPPLY OF NERI ARCHITECTURAL POST TOP POLE - JM.02.23.053 - 3.5M height post top Pole Made of hot dip galvanised mild steel pipe sections 114mm dia. & 76mm dia. Arch. Base design starts with 322mm Dia. ring , radially tapers to 215mm for a height of 70mm, which is followed by a ring of 215mm dia,, then radially tapers to 135mm for a height of 115mm .Total weight of the base is 15 Kgs. & height of the base is 235mm . Ring-1(114mm/76mm, weight- 4kgs.) & Top Ring-(weight- 3kgs.) are made of cast iron. Entire pole & Bracket including all the cast iron elements shall be made to provide pleasing aesthetics as approved by Concerned Engineer in-charge. After Fabrication, Entire Pole is hot dip galvanized(60 microns Minimum ) for the effective corrosion resistance. The hot dip Galvanised pole should be provided with an inbuilt junction box to fix 32A connectors and 6A MCB, at the bottom - the inbuilt box should have a flush door of suitable size. The pole to be provide with suitable size base plate. This base plate along with foundation bolts of suitable size to be used for ensuring firm grouting into the specially designed RCC foundation. wind pressure calculation as per IS 875(part-3) & structural calculation report as per EN40 should be submitted to verify the pole design. Pole & Cast iron parts are painted in 3 layer coating(coating thickness-100 microns minimum) in which 1st layer with etch primer, 2nd layer with epoxy primer & 3rd final layer with PU paint - customised colour Metallaic NERI Grey.

SUPPLYOF NERI ARCHITECTURAL LED LIGHT FIXTURE MODEL - LIGHT 21 (30W-40W) Power Module LED, 4000K, Upright Type - Light 21: Upper frame with threaded coupling G3/4" for suspended mounting. at the top, made of die cast aluminum using pressure die-casting process. in single piece. Lower frame composed by a ring made of die cast aluminum using pressure die-casting process in single piece. Auxiliary and optical compartment can be accessed by opening the frames. Company /brand name should be engraved in the mold of the body. Drop shaped screen in polymethylmethacrylate (PMMA), transparent made in single piece using injection moulding process. Silicone gasket between the upper and lower frames. Finish-Pure polyester powder coating in Grey Colour.optical compartment IP Rating - IP 66.. Height – 545mm,Diameter - 550mm,Weight - 8Kgs.,. Power LED Module with Company /brand name printed on PCB with the metal core plate.LED Chips of CREE/NICHIA/OSRAM/LUMILEDS make - same should be supported by LED manufacturer's tech sheet . Colour Rendering Index: Ra > 70. Electronic Power Supply for LED Module, which offers Protection against Short Circuit, Over- Voltage & Over- Current, with in-built surge protection (an additional surge protection device of 10kV also provided in-built the fixture). Optics with refractive lens in PMMA which should offer all the Type II,III,IV & V distribtuions. LED Lifetime @L90 >1,00,000hours@Ts 85°C. LM80 report from LED Manufacturer should be submitted. Safety test report as per IEC 60598 from UL/UL authorised/Intertek. LM79 report also should be submitted from UL/UL Authorised/Intertek Laboratory. Sample should be submitted for approval from concerned engineer-in charge.SUPPLYOF NERI ARCHITECTURAL LED LIGHT FIXTURE MODEL - LIGHT 21 (30W-40W) Power Module LED, 4000K, Upright Type - Light 21: Upper frame with threaded coupling G3/4" for suspended mounting. at the top, made of die cast aluminum using pressure die-casting process. in single piece. Lower frame composed by a ring made of die cast aluminum using pressure die-casting process in single piece. Auxiliary and optical compartment can be accessed by opening the frames. Company /brand name should be engraved in the mold of the body. Drop shaped screen in polymethylmethacrylate (PMMA), transparent made in single piece using injection moulding process. Silicone gasket between the upper and lower frames. Finish-Pure polyester powder coating in Grey Colour.optical compartment IP Rating - IP 66.. Height – 545mm,Diameter - 550mm,Weight - 8Kgs.,. Power LED Module with Company /brand name printed on PCB with the metal core plate.LED Chips of CREE/NICHIA/OSRAM/LUMILEDS make - same should be supported by LED manufacturer's tech sheet . Colour Rendering Index: Ra > 70. Electronic Power Supply for LED Module, which offers Protection against Short Circuit, Over- Voltage & Over- Current, with in-built surge protection (an additional surge protection device of 10kV also provided in-built the fixture). Optics with refractive lens in PMMA which should offer all the Type II,III,IV & V distribtuions. LED Lifetime @L90 >1,00,000hours@Ts 85°C. LM80 report from LED Manufacturer should be submitted. Safety test report as per IEC 60598 from UL/UL authorised/Intertek. LM79 report also should be submitted from UL/UL Authorised/Intertek Laboratory. Sample should be submitted for approval from concerned engineer-in charge.

SUPPLY OF NERI ARCHITECTURAL LED Strip - NLS-5, 5W/M, LED, 3000k, DC24V, IP 67 FOR SWING SEATER - NLS-5: Silicon material-Much more flexible,Efficient heat dissipation,Smooth plane lighting surface,Perfect resealing with silicone glue. Mounting channel made of aluminium with acrylic diffuser screen, LED-DC 24V, source Efficacy>90lm/W,CRI>80,SMD LED,yellow glue 3M,120 degree beam angle,It also includes External IP67 metal body Electronic Power Supply(Meanwell XLG-Equivalent) for LED strip,which offers Protection against Short Circuit, Over- Voltage & Over- Current, with in-built surge protection. .

SUPPLY OF NERI ARCHITECTURAL LED Strip - NLS-5, 5W/M, LED, 3000k, DC24V, IP 67 FOR MS PERAGOLA TYPE-01 - NLS-5: Silicon material-Much more flexible,Efficient heat dissipation,Smooth plane lighting surface,Perfect resealing with silicone glue. Mounting channel made of aluminium with acrylic diffuser screen, LED-DC 24V, source Efficacy>90lm/W,CRI>80,SMD LED,yellow glue 3M,120 degree beam angle,It also includes External IP67 metal body Electronic Power Supply(Meanwell XLG-Equivalent) for LED strip,which offers Protection against Short Circuit, Over- Voltage & Over- Current, with in-built surge protection.

SUPPLY OF NERI ARCHITECTURAL LED Strip - NLS-5, 5W/M, LED, 3000k, DC24V, IP 67 FOR SIGNAGE - NLS-5: Silicon material-Much more flexible,Efficient heat dissipation,Smooth plane lighting surface,Perfect resealing with silicone glue. Mounting channel made of aluminium with acrylic diffuser screen, LED-DC 24V, source Efficacy>90lm/W,CRI>80,SMD LED,yellow glue 3M,120 degree beam angle,It also includes External IP67 metal body Electronic Power Supply(Meanwell XLG-Equivalent) for LED strip,which offers Protection against Short Circuit, Over- Voltage & Over- Current, with in-built surge protection.

SUPPLY OF NERI ARCHITECTURAL LED Strip - NLS-5, 5W/M, LED, 3000k, DC24V, IP 67 FOR MAP SIGNAGE- NLS-5: Silicon material-Much more flexible,Efficient heat dissipation,Smooth plane lighting surface,Perfect resealing with silicone glue. Mounting channel made of aluminium with acrylic diffuser screen, LED-DC 24V, source Efficacy>90lm/W,CRI>80,SMD LED,yellow glue 3M,120 degree beam angle,It also includes External IP67 metal body Electronic Power Supply(Meanwell XLG-Equivalent) for LED strip,which offers Protection against Short Circuit, Over- Voltage & Over- Current, with in-built surge protection.

SUPPLY OF NERI ARCHITECTURAL LED PROJECTOR LIGHT FIXTURE NSL-10S (8-12W), LED,3000K, IP 66 - NSL-10S: NSL-10S- Body in cylindrical shape made of Die-cast and extruded aluminium and finished with pure polyester powder coating in grey colour. Screen in flat tempered glass. Dimension-65mm(Dia.)x220mm(L),Weight-1kgs. Electronic Driver which offers Protection against Short Circuit, Over- Voltage, Over- Current & inbuilt surge protection., IP 66 protection, CRI > 80, voltage input AC240V. Estimated Lifetime-L70 @ 50,000hours minimum. LM80 report from LED Manufacturer should be submitted. Sample should be submitted for approval from concerned engineer-in charge. SUPPLY OF NERI ARCHITECTURAL LED PROJECTOR LIGHT FIXTURE NSL-10S (8-12W), LED,3000K, IP 66 FOR CNC CUT SIGNAGE - NSL-10S: NSL-10S- Body in cylindrical shape made of Die-cast and extruded aluminium and finished with pure polyester powder coating in grey colour. Screen in flat tempered glass. Dimension-65mm(Dia.)x220mm(L),Weight-1kgs. Electronic Driver which offers Protection against Short Circuit, Over- Voltage, Over- Current & inbuilt surge protection., IP 66 protection, CRI > 80, voltage input AC240V. Estimated Lifetime-L70 @ 50,000hours minimum. LM80 report from LED Manufacturer should be submitted. Sample should be submitted for approval from concerned engineer-in charge.

SUPPLY OF NERI ARCHITECTURAL LED PROJECTOR LIGHT FIXTURE NPL-3-9, (20W-25W), LED, RGBW, IP 66 FOR 3.75M HEIGHT GLASS LIGHT COLUMN - NPL-3-9: The housing in light weight, made of high strength die cast aluminium and coated by static powder making it weather resistant.Protection screen in ultra white tempered glass with high impact resistance . High precision dial ensures precision angle adjustment.Premium thermal management by high heat conductivity aluminum alloy and thermal fins. Pure Polyester powder coating in Standard Grey Colour. Precise structure and multi-protection silicon rubber seal guarantees the fixture IP66 rated. Height – 122mm, Dia.-170mm, Weight - 2Kgs. Power LED Module with high efficacy LED's, on Printed Circuit Board with metal core plate. Common external electronic Power Supply for LED Module,which offers Protection against Short Circuit, Over- Voltage & Over- Current, with in-built surge protection. Light fixture should be standard DMX512 protocol compatible, the DMX decoder function should be inbuilt the light fixture,Each light fixture should be invidually addressable & should be able to operate with any standard DMX512 equipment.Lens made of PC which should offer various beam angles. Estimated LED Lifetime is L70-50,000 hours minimum. Minimum Light fixture Lumen output is 1000Lumens @full power. LM80 report from LED Manufacturer should be submitted. Safety test report as per IEC 60598 from UL/UL authorised/Intertek. BIS Certificate with manufacturer name same as brand proposed should be submitted. Sample should be submitted for approval from concerned engineer-in charge.SUPPLY OF NERI ARCHITECTURAL LED PROJECTOR LIGHT FIXTURE NPL-3-9, (20W-25W), LED, RGBW, IP 66 FOR 3.75M HEIGHT GLASS LIGHT COLUMN - NPL-3-9: The housing in light weight, made of high strength die cast aluminium and coated by static powder making it weather resistant.Protection screen in ultra white tempered glass with high impact resistance . High precision dial ensures precision angle adjustment.Premium thermal management by high heat conductivity aluminum alloy and thermal fins. Pure Polyester powder coating in Standard Grey Colour. Precise structure and multi-protection silicon rubber seal guarantees the fixture IP66 rated. Height – 122mm, Dia.-170mm, Weight - 2Kgs. Power LED Module with high efficacy LED's, on Printed Circuit Board with metal core plate. Common external electronic Power Supply for LED Module,which offers Protection against Short Circuit, Over- Voltage & Over- Current, with in-built surge protection. Light fixture should be standard DMX512 protocol compatible, the DMX decoder function should be inbuilt the light fixture,Each light fixture should be invidually addressable & should be able to operate with any standard DMX512 equipment.Lens made of PC which should offer various beam angles. Estimated LED Lifetime is L70-50,000 hours minimum. Minimum Light fixture Lumen output is 1000Lumens @full power. LM80 report from LED Manufacturer should be submitted. Safety test report as per IEC 60598 from UL/UL authorised/Intertek. BIS Certificate with manufacturer name same as brand proposed should be submitted. Sample should be submitted for approval from concerned engineer-in charge.

SUPPLY OF NERI ARCHITECTURAL LED PROJECTOR LIGHT FIXTURE NSL-10S (8-12W), LED,3000K, IP 66 FOR 2.6M HEIGHT VERTICAL COLUMN ( 2 SIDE LIGHT SCREEN) -NSL-10S- Body in cylindrical shape made of Die-cast and extruded aluminium and finished with pure polyester powder coating in grey colour. Screen in flat tempered glass. Dimension-65mm(Dia.)x220mm(L),Weight-1kgs. Electronic Driver which offers Protection against Short Circuit, Over- Voltage, Over- Current & inbuilt surge protection., IP 66 protection, CRI > 80, voltage input AC240V. Estimated Lifetime-L70 @ 50,000hours minimum. LM80 report from LED Manufacturer should be submitted. Sample should be submitted for approval from concerned engineer-in charge. SUPPLY OF NERI ARCHITECTURAL LED PROJECTOR LIGHT FIXTURE NSL-10S (8-12W), LED,3000K, IP 66 FOR 2.6M HEIGHT VERTICAL COLUMN ( 2 SIDE LIGHT SCREEN) -NSL-10S- Body in cylindrical shape made of Die-cast and extruded aluminium and finished with pure polyester powder coating in grey colour. Screen in flat tempered glass. Dimension-65mm(Dia.)x220mm(L),Weight-1kgs. Electronic Driver which offers Protection against Short Circuit, Over- Voltage, Over- Current & inbuilt surge protection., IP 66 protection, CRI > 80, voltage input AC240V. Estimated Lifetime-L70 @ 50,000hours minimum. LM80 report from LED Manufacturer should be submitted. Sample should be submitted for approval from concerned engineer-in charge.

SUPPLY OF NERI ARCHITECTURAL LED PROJECTOR LIGHT FIXTURE- MODEL - NSL-20S,( 18W-22W), LED, 3000K, IP 66 FOR TENSILE STRUCTURE - NSL-20S- Body in cylindrical shape made of Die-cast and extruded aluminium and finished with pure polyester powder coating in grey colour. Screen in flat tempered glass. Dimension-90mm(Dia.)x220mm(L),Weight-1kgs. Electronic Driver which offers Protection against Short Circuit, Over- Voltage, Over- Current & inbuilt surge protection., IP 66 protection, CRI > 80, voltage input AC240V. Estimated Lifetime-L70 @ 50,000hours minimum. LM80 report from LED Manufacturer should be submitted. Sample should be submitted for approval from concerned engineer-in charge.

SUPPLY OF NERI ARCHITECTURAL LED PROJECTOR LIGHT FIXTURE NSL-10S (8-12W), LED,3000K,IP 66 FOR 4.7M SUB VISUAL MARKER -NSL-10S- Body in cylindrical shape made of Die-cast and extruded aluminium and finished with pure polyester powder coating in grey colour. Screen in flat tempered glass. Dimension-65mm(Dia.)x220mm(L),Weight-1kgs. Electronic Driver which offers Protection against Short Circuit, Over- Voltage, Over- Current & inbuilt surge protection., IP 66 protection, CRI > 80, voltage input AC240V. Estimated Lifetime-L70 @ 50,000hours minimum. LM80 report from LED Manufacturer should be submitted. Sample should be submitted for approval from concerned engineer-in charge.

SUPPLY OF NERI ARCHITECTURAL LED RGBW PROJECTOR LIGHT FIXTURE - NSL-30S (25-35W), LED,3000K,IP 66 FOR METRO STATION FAÇADE ROUND PILLARS -NSL-30S- Body in cylindrical shape made of Die-cast and extruded aluminium and finished with pure polyester powder coating in grey colour. Screen in flat tempered glass. Dimension-108mm(Dia.)x260mm(L),Weight-1.5kgs. Electronic Driver which offers Protection against Short Circuit, Over- Voltage, Over- Current & inbuilt surge protection., IP 66 protection, CRI > 80, voltage input AC240V. Estimated Lifetime-L70 @ 50,000hours minimum. LM80 report from LED Manufacturer should be submitted. Sample should be submitted for approval from concerned engineer-in charge.

SUPPLY OF NERI ARCHITECTURAL LED RGBW PROJECTOR LIGHT FIXTURE MODEL NPL-3-12, (25W-30W), LED, RGBW, IP 66 - FOR METRO STATION FAÇADE (57nos for New Washermanpet Metro, 77 nos for Tollgate Metro) - NPL-3-12: The housing in light weight, made of high strength die cast aluminium and coated by static powder making it weather resistant.Protection screen in ultra white tempered glass with high impact resistance . High precision dial ensures precision angle adjustment.Premium thermal management by high heat conductivity aluminum alloy and thermal fins. Pure Polyester powder coating in Standard Grey Colour. Precise structure and multi-protection silicon rubber seal guarantees the fixture IP66 rated. Height – 122mm, Dia.-170mm, Weight - 2Kgs.Power LED Module with high efficacy LED's, on Printed Circuit Board with metal core plate. Common external electronic Power Supply for LED Module,which offers Protection against Short Circuit, Over- Voltage & Over- Current, with in-built surge protection. Light fixture should be standard DMX512 protocol compatible, the DMX decoder function should be inbuilt the light fixture,Each light fixture should be invidually addressable & should be able to operate with any standard DMX512 equipment. Lens made of PC which should offer various beam angles. Estimated LED Lifetime is L70-50,000 hours minimum. Minimum Light fixture Lumen output is 1350Lumens @full power. LM80 report from LED Manufacturer should be submitted. Safety test report as per IEC 60598 from UL/UL authorised/Intertek. BIS Certificate with manufacturer name same as brand proposed should be submitted. Sample should be submitted for approval from concerned engineer-in charge.

SUPPLY OF NERI ARCHITECTURAL WALL WASHER LED LIGH FIXTURE - MODEL - NWWL-7-24, (40W-50W), LED, RGBW, IP 66, DC 24V(External driver), 1M Length FOR METRO STATION FAÇADE (52 nos for New Washermanpet Metro, 52 nos for Tollgate Metro) - NWWL-7-24: The housing in light weight, made of high strength aluminium and coated by static powder making it weather resistant.Protection screen in tempered glass with high impact resistance . High precision dial ensures precision angle adjustment. Pure Polyester powder coating in Standard Grey Colour. Precise structure and multi-protection silicon rubber seal guarantees the fixture IP66 rated. Length-1000mm,Height – 30mm, Width.-38mm, Weight - 2Kgs.Power LED Module with high efficacy LED's, on Printed Circuit Board with metal core plate. Common external electronic Power Supply for LED Module,which offers Protection against Short Circuit, Over- Voltage & Over- Current, with in-built surge protection. Light fixture should be standard DMX512 protocol compatible, the DMX decoder function should be inbuilt the light fixture,Each light fixture should be invidually addressable & should be able to operate with any standard DMX512 equipment. Lens made of PC which should offer various beam angles. Estimated LED Lifetime is L70-50,000 hours minimum. LM80 report from LED Manufacturer should be submitted. Safety test report as per IS10322/IEC 60598 from UL/UL authorised/3rd party NABL lab should be submitted. BIS Certificate with manufacturer name same as brand proposed should be submitted. Minimum Light fixture Lumen output is 1450 Lumens @full power. Sample Should be submitted for concerned engineer incharge for approval of light fixture.

SUPPLY OF 2 Universe (1024 Channels) DMX controller with following features & specifications: This is built on the latest generation of lighting controllers and combines all recent innovations. Designed for DIN rail mounting, this is the perfect solution for midrange lighting installations. Delivered with 1024 DMX channels.The lighting levels, color and effects can be programmed from a PC, Mac, Android, iPad or iPhone using software from our website.It's Key Features includes • DMX Stand Alone controller • Up to 2 x DMX512 universes (1024 channels) • RDM compatible • USB & Ethernet connectivity for programming/ control • Stand Alone mode with 99 scenes • Play scenes in 5 areas / zones • microSD slot • 8+3 dry contact trigger ports • Test scenes rotary switch • Windows/Mac software to set dynamic colors/effects • iPhone/iPad/Android remote and programming apps • cloud compatibility.Technical Data Input Power 12v DC (8-15V range), Output Protocol DMX512 , Programmability PC, Mac, Android, iOS, Connections-USB-C Ethernet Screw terminals for DMX / RDM Universes, 8+3 Contact ports, 12v power-in Battery holder (CR2032), microSD slot Memory SD Card ,Environment IP20 / to 0 to +50°C, Buttons Rotary switch ,OS Requirements Mac OS X 10.8-10.14 Windows 7/8/10 Standards CE, ETL, Low voltage, EMC, and RoHS

SUPPLY OF 6port DMX Splitter(Din rail Mountable)with following features & specifications: DMX signal splitter enables branching in complex DMX installations. The combination of a large number of receivers in series can be troublesome, therefore it was possible to create branching DMX tracks using a splitter.With Splitter, it possible to split the DMX input signal into 6 independent branches. The individual outputs are galvanically isolated from input and between each other. The output signals are appropriately reinforces, which guarantees correct operation of the entire installation. DMX Splitter is manufactured in a housing adapted for mounting on standard DIN 35mm rails. Specification - Power Supply-DC12-24V,DMX Channels--512,nos. of DMX Inout-1 & output-6,Optical Isolation of DMX Lines,Built-in Terminatior,breakdown voltage of the isolation>1000V,current consumption-<500mA,Weight-0.2Kgs.,W-105mm,H-86mm&D-60mm.

Programming of DMX system. Minimum of 10 scenes need to be configured.

Supply and Laying of 1.1 KV grade XLPE insulated PVC sheathed armoured Al. Conductor cables confirming to IS: 7908 Part I 1988 of following sizes as per technical specification. 3 1/2C x 70 Sq mm Al. Ar XLPE Cable for Pillar Box to SSB

4C x 25 Sq mm Al. Ar XLPE Cable for LSB to LDB & PDB

4C x 4 Sqmm Al. Ar XLPE Cable for LDB to street light pole

3c x 2.5 Sqmm Copper Ar XLPE Cable for Toilet Area Incoming and Small Light Point

Supply and Fixing of End Termination of the following cables by using of siemens type & Flange type glands, crimping sockets and glands earthing with all accessories required to complete the work. 3 1/2C x 70 Sq mm Al. Ar XLPE Cable

4C x 25 Sq mm Al. Ar XLPE Cable

4C x 4 Sqmm Al. Ar XLPE Cable

3c x 2.5 Sqmm Copper Ar XLPE Cable

Supply and Providing of safe ear thing electrode of 3 rmt long 50mm dia with 2 bag back fill compound with mixture of ,GI bolt nut etc, completely as per IS 3043, 1987 or latest revision. (ELECTRODE SAFE EARTH CAT ) (Earth pipe should be near to the Panel Board)

Supply & Erection of 32mm dia, 1 Mtr length GI Earth pipe (C Class) with 8 SWG GI wire earthing of street light pole with complete accessories (Earth pipe should be near to the )

Supply and Laying of G.I Flat for the following sizes of earth wires and earth flat, , bolt nuts and washers etc., required to complete the work. Supply and Laying of 50mm x 6mm G.I Flat Hot Dipped

Supply and Laying of 25mm x 6mm G.I Flat Hot Dipped

Supply and Laying of 8 SWG G.I wire

Supply and Wiring with 2 runs of 1.5 sqmm PVC insulated 1100 V grade FRLS copper wire for Ph/neutral and 1 run of 1 sq. mm FRLS copper wire for earth in 19/25mm MS conduit pipe of 2mm thickness run on wall / ceiling with complete with all accessories, including providing modular type switch for control housed in a zinc passivated MS Box of approved make including giving necessary connections for Light point. Single light point controlled by single switch

1 Fan control by 1 No & 100W Regulator

Supply and Wiring with 2 runs of 1.5 sqmm PVC insulated 1100 V grade FRLS copper wire for Ph/neutral and 1 run of 1 sq. mm FRLS copper wire for earth in 19/25mm MS conduit pipe of 2mm thickness run on wall / ceiling with complete with all accessories, including providing modular type switch for control housed in a zinc passivated MS Box of approved make including giving necessary connections for Exhaust-Fan point.

Supply and Wiring with 2 runs of 1.5 sqmm PVC insulated 1100 V grade FRLS copper wire for Ph/neutral and 1 run of 1 sq. mm FRLS copper wire for earth in 19/25mm MS conduit pipe of 2mm thickness run on wall / ceiling with Complete with all accessories for Excess Length.(Light point)

Supply and Wiring with 2 runs of 2.5 sqmm PVC insulated 1100 V grade FRLS copper wire for Ph/neutral and 1 run of 1.5 sq. mm FRLS copper wire for earth in 19/25mm MS conduit pipe of 2mm thickness run on wall / ceiling with complete With all accessories for Power point

Supply and fixing of 6A Switch and 6A Multi pin Socket for on board 6A Plug Point.

Supply and fixing of 16A Switch with indicator and 6/16A Multi pin Socket for control housed in a zinc passivated MS Box of approved make including giving necessary connections for 6/16A Plug Point.

Supply and Fixing of 1 x 20W LED light fitting – 4feet

Supply and Erection of 300mm Sweep Metal Exhaust Fan with fitting including frame

Supply & Laying of following sizes of MS conduit with all accessories in recessed conduit system. Rate should be included for providing necessary junction box and GI pull wire as required. 32 mm Dia 2mm thick MS conduit

25 mm Dia 2mm thick MS conduit

19 mm Dia 2mm thick MS conduit

Supply & Laying of 2" dia PVC with minimum thickness of 3mm with all its accessories required.

Supply and Fixing of PVC Junction Box waterproof suitable above Pipe

Supply & Laying of 3" dia PVC with minimum thickness of 3mm with all its accessories required.

Supply and Fixing of PVC Junction Box waterproof suitable above Pipe

Supply & Erection of 200mm Dia Hume Pipe for road crossings etc. as per Site Requirement for Electrical

Supply & Fabrication erection of MS item for electrical Equipment supported item

Resources allocated to EHS management: Environment, Health and Safety manager.(B.Tech in Environment)

Resources allocated to EHS management: Community Liasion Officer

Measures for Traffic, noise from vehicle ,plant and equipment’s and atmospheric emissions management including dust pollution to nearby settlement areas .

Waste and hazardous products management, management of oil and grease waste in a separate storage place with proper ventilation

ENVIRONMENT MONITORING PLAN The following tests to be conducted through NABL accredited Lab approved by MoEF &CC Air Quality Monitoring ( PM 10 ,PM 2.5,SO2 ,NOx and CO)- 3 sensitive locations for 3 seasons per year during construction & operation phase

Noise Level Monitoring - (Leg dB (A)Average and Peak value Hourly measurement during day ) 3 sensitive locations for 3 seasons/year during construction & operation phase

Surface Water Quality Monitoring (BoD , pH, TDS, Total hardness Sulphate, Fluorides, Chloride, Fe, Pb)- 3 sensitive locations for 2 seasons/year during construction & operation period

Ground Water Quality Monitoring (BoD , pH, TDS, Total hardness Sulphate, Fluorides, Chloride, Fe, Pb)- 3 sensitive locations for 3 seasons/year during construction & operation period

Soil/Silt Quality monitoring (SAR, Oil & Grease, Texture, Lead, Arsenic, Cadmium, Mercury, Iron, Copper, Zinc,Nickel, Chromium, Manganese, PH, conductivity)-3 sensitve locations once in a year during construction & operation

GURUMURTHY ENGINEERING ENTERPRISES (BID ID -1066389)