REPAIRS TO ROOF, PPGL SHEETS, ROOF TREATMENT, FLOORING, HARDSTANDING AND MISC B/R RELATED WORKS IN AOP AREA INCLUDING HANGERS OF ARMY AVN SQN UNDER GE NASIK ROAD.

Amount

Demolition of concrete in ground floors and pavings n exc 15cm thickness (below or above ground level) and removing the debris out of MOD land.

M&L for 75 mm thick Plain cement concrete, 1:4:8, type D-2 (using 40mm graded aggregate) as in sub base. Note:mixing of concrete by machine only

M&L for 50 mm thick Plain cement concrete, 1:4:8, type D-2 (using 40mm graded aggregate) as in sub base. Note:mixing of concrete by machine only

M&L for 100 mm thick Plain cement concrete 1:2:4,Type B-2 (using 20mm graded aggregate) as in flooring over and including provision of 2mm thick pvc dividing strip for joints.complete all as per SSR Part-I. Note:mixing of concrete by machine only.

M&L for broken stone/boudlers as in Hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed by engr-in-charge.

M&L for Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering. Note.Moorum to be brought out of MOD land.quoted rate also deemed to be inclusive of surface dressing and site clearance.

M&L for Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand;over and including provision of PCC 1:2:4 type B0 as in filleting/edging to the sides of paver path/hardstanding in size and shape as directed by engr-in-charge.

M&L for Chequered cement concrete tiles with grey cement and pigment 30cm x 30cm x 25mm thick, with rubber moulded glossy finished surface, laid in floors over and including 15mm thick cement mortar screed bed in cement mortar 1:6, set jointed and pointed in neat cement slurry in floors.over and including provision of PCC 1:2:4 as in filleting/edging to the sides of paver path/hardstanding as per standard engineering practice to the entire satisfaction of engr-in-charge.

M&L for Rough Shahabad stone 25 mm to 30 mm thick in flooring/plinth set and jointed in in neat cement slurry and pointed in CM 1:4 complete all as specified and directed over and including 15mm thick screed bed in cement mortar 1:6.over and including provision of PCC 1:2:4 as in filleting/edging to the sides as per standard engineering practice to the entire satisfaction of engr-in-charge.

Dismantling stone slabs and tiles of any description or thickness in floors, aprons etc. laid, bedded and pointed in any mortar and removing the debris out of MOD land.

M&L for 18 to 20mm thick Granite of any type work (table rubbed and polished) in steps, jambs pillars, window cills cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture re of pigment to match with shade of granite 18 to 20mm thick all as specified and directed.

M&L for Machine cut cudappah stone slab 20-25mm thick over 10mm thick cement screed base in CM 1:4, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete

Dismantling of precast concrete articles and precast concrete block set or built in cement mortar and removing the debris out of MOD land.

M&L for Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete over and including applying two coats of synthetic enamel paint over a coat of primer.

Demolition of brickwork or stone/boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc.and removing the debris out of MOD land.

M&L for brick work with fly ash bricks straight or curved on plan exc 6 m mean radius built in CM 1:6 inlcluding raking out joints on both faces of wall.

Taking down completely cement or cement lime plaster, any description on brick or stone walls/ceiling, etc. including raking out joints, hacking for key, scrubbing down with water, etc. Note: work to be executed at any height and situation.

M&L for Rendering 15 mm thick in cement mortar 1:4 on brick wall/concrete surfaces finished fair and even and curing as per standard engineering practice. Note: work to be executed at any height and situation.

M&L for rendering 10mm thick in CM 1:6 on brick wall/concrete surfaces finished fair and even.

M&L for two coats of exterior emulsion paint on wall surface. Note: work to be executed at any height and situation.

M&L for two coats of exterior emulsion paint on ceiling surface. Note:work to be executed at any height and situation.

M&L for two coats of cement base paint on brick wall/concrete surfaces over a coat of primer including preparation of surfaces. Note:work is to be executed at any height and situation.

M&L for applying two coats of distemper oil emulsion on wall surfaces.

M&L for applying two coats of distemper oil emulsion on Ceiling surfaces.

M&L for applying one coats of distemper oil emulsion on wall surfaces. .

M&L for applying one coats of distemper oil emulsion on Ceiling surfaces.

M&L for 1.5 mm thick(in two coats) acrylic wall care putty on wall Surfaces as per manufacturers instruction.

M&L for 1.5 mm thick (in two coats) acrylic wall care putty on ceiling surfaces as per manufacturers instructions.

M&L for 1.00 mm thick acrylic wall care putty on walls incl preparation of surfaces,filling holes and cracks with putty,rubbing,making surface even to the entire satisfaction of ground executives.

M&L for 1.00 mm thick acrylic wall care putty on ceilings incl preparation of surfaces,filling holes and cracks with putty,rubbing,making surface even to the entire satisfaction of ground executives.

M&L for applying two coats of interior primer on wall surfaces as per manufacutrers instruction.

M&L for applying two coats of interior primer on ceiling surfaces as per manufacutrers instruction.

M&L for applying one coats of interior primer on wall surfaces as per manufacutrers instruction.

M&L for applying one coats of interior primer on ceiling surfaces as per manufacutrers instruction.

M&L for applying one coat of exterior primer on wall surfaces as per manufacuters instructions. Note: work to be executed at any height.

M&L for applying one coat of exterior primer on ceiling surfaces as per manufacuters instructions. Note:work to be executed at any height.

M&L for applying two coats of exterior primer on wall surfaces as per manufacuters instruction.

M&L for applying two coats of exterior primer on ceiling surfaces as per manufacuters instruction.

M&L for preparation of old surfaces of wall surfaces by brooming down or steel wire brushing;washing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots;washing, removing nails,removing vegetation growth of any size and penetration on wall to the entire satisfaction of ground executives, sealing holes,cracks of any width/depth using waterproof crack sealing compound of premium quality as approved by GE. Note:work to be executed at any height and situation.

M&L for preparation of old surfaces of ceiling surfaces by brooming down or steel wire brushing;washing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots;washing, removing nails,removing vegetation growth of any size and penetration ceiling to the entire satisfaction of ground executives, sealing holes,cracks of any width/depth using waterproof crack sealing compound of premium quality as approved by GE. Note:work to be executed at any height and situation.

M&L for applying two coats of exterior emulsion paint on wall surfaces.

M&L for applying two coats of exterior emulsion paint on ceiling surfaces.

M&L for Providing, cement concrete 1:2:4, type B-1 (using 20 mm graded aggregate) in copings and the like including weathering, slightly rounded or chamfered angles and throating, as directed and finnshing the surfaces of concrete.

Demolition of concrete of any description and in any position.

M&L for Plain cement concrete 1:4:8, type D-2(using 40 mm graded aggregate) as in foundations, filling and mass concrete over and including preparation of surfaces.

Dismantling wrought iron or mild any description such as steel gate, steel frame works, purlins, rafter, railings, balusters and window guard bars and directed by Engr-in-Charge. Note:work is to be executed at any height and situation.

S&F steel work in tubular pipes including special shaped washer etc complete using ERW or induction butt welded tubes conforming to IS 4923:1997 Grade YSt-210 complete all over and including two coats of synthetic enamel paint over a coat of red oxide primer. Note. work is to be executed at any height and situation like hangars etc.

Dismantling Plain or corrugated steel sheeting of any gauge,thickness,including Nainital or similar pattern roof coverings complete all as specified and as directed. Note. work is to be executed at any height and situation like hangars etc

S&F Prepainted Galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength 550 mpa as in roof covering/cladding to wall,fixed with self tapping screw complete all as specified and as directed. Gap between wall face and sheet if any shall be sealed using CM 1:3 with WPC.quoted rate deemed to be inclusive of the same. Note : Note: work is to be executed at any height and situation like hangars etc.

S&F Prepainted Galvalume aluminium zinc coating GI based Plain sheet 0.50 mm thick of any colour having tensile strength 550 mpa as in roof covering/cladding to wall,fixed with self tapping screw complete all as specified and as directed. Note: work is to be executed at any height and situation.

M&L for 2 mm thick fiber glass sheet (plain/corrugated) as in roof covering/cladding to wall fixed with self tapping screws complete all as specified and directed by engr-in-charge. Note.The work is to be executed at any height and situation like hangars etc.

Dismantling barbed wire fixed to any type of standard rails straining bolts (each line wire to be measured).

Dismantling RCC posts or struts any section, embedded in concrete, brick work, masonry etc. including taking out embedded portion and making good disturbed ground and removing the debris out of MOD land.

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth round, in layers not exceeding 25 cm in soft/loose soil.

M&L for Plain Cement concrete 1:2:4 type B-1(using 40 mm graded aggregate) as in foundations, filling and mass concrete.

S&F 45mm to 50mm thick precast 1:2:4,type B0 (using 12.5 mm graded stone aggregate) panels/planks of approved design as in compound wall ,locking each other as per approved design/pattern in precast RCC post,set in cm as 1:4,(measured solid),including all moulding but excluding frame and including dismantling old unserviceable precast wall and removing debris out of MOD land,complete all as specified and directed. Note: The quoted rate shall be inclusive of cost of reinforcement,formwork.

M&L for providing precast RCC 1:2:4,type B-1(20mm graded stone aggregate) as in columns,posts,boundary pillars with grooves to lock RCC planks/panels and set in mortar 1:4 complete all as specified and directed. Note. The quoted rate shall be inclusive of cost of reinforcement,formwork.

M&L for Repairing of broken edges of RCC chajjas, roof projections, fins, facia and similar works by dismantling of loose and damaged/ disintegrated portion of edges (cross sectional area not exceeding 150 sqcm) with cement mortar 1:4 or cement concrete 1:1½:3 type A0 and chicken wire mesh with nails (to hold fresh mortar/concrete) including necessary formwork etc., Note: work to be executed for hangars etc.

Taking down carefully existing bituminous membrane/tarfelt treatment any description and cleaning and making good minor damaged surface of roof ,parapet,facia etc.quotated rate shall be deemed to be inclusive of complete removal of swollen plaster.and removing rubbish out of defence land. Note: work is to be executed at any height and situation.

M&L for Plain cement concrete 1:2:4,type B0(using 12.5mm graded aggregate) in roof kerbs or mud stops,ridge,padding, rounded or chamfered on edges.

M&L for rendering 15 mm thick(minimum) in CM 1:4 liquid waterproofing compound (200 ml per bag of cement used) on roof surfaces,parapets,facias etc .curing as per standard eng practices. Note: waterproofing compound shall be measured and paid separately.

Supplying only Liquid water proofing compound ISI marked complete all as specified and as directed.

M&L for Applying evenly a coat of hot blown bitumen 85/25 over roof surface,facia,parapet etc at the rate of 1.2 kg per sqm for fixing app membrane etc including cleaning surfaces.

M&L for Waterproofing on roof including flashing and junctions of parapet,kerb, wall etc.as under :- (a) Laying a layer of APP based polymeric membrane,3 mm thick(minimum),weighing not less than 3.60 kg/Sqm prefabricated fire layer waterproofing membrane reinforced with polyester non woven fabric(weighing not less than 160 gms/sqm) shall be applied over compatible primer(oil based) at 0.40 litre/Sqm of density at 25 degree Centigrade 0.87-0.89 Kg /Litre and viscosity 70-160cps or cold sticker, application of APP modified membrance shall be by torch application. The overlaps shall be minimum 150mm on the transverse direction and 100 mm on the longitudinal direction. (b) APP membrance,Primer and bitumastic aluminium paint shall be of same brand. (c) For vertical surfaces i.e. parapets,wall etc. app membrane shall be tucked into groove and sealed with silicon sealant i.e. "Dowsil 789 weatherproofing silicon sealant" using gun. (d) Bitumen and aluminium paint shall be paid separately.

M&L for applying two coats of solar reflective bitumastic aluminium paint at the rate 0.15L/sqm per two coats over exposed app membrane surfaces(old/new) including preparation of surfaces to the entire satisfaction of ground executives.

Disconnecting existing tanks exc 250 n exc 500 ltrs, setting aside (or lowering if required) cleaning and removing all scale dirt,etc from the mouth of circulating pipes etc and hoisting if required,reconnecting and re-fixing in position. Note: work is to be executed at any height and situation.

Disconnecting existing tanks exc 500 n exc 1000 Ltrs, setting aside (or lowering if required) cleaning and removing all scale dirt,etc from the mouth of circulating pipes etc and hoisting if required,reconnecting and re-fixing in position. Note: work is to be executed at any height and situation.

Taking down AC rain water pipes(any size or pattern) including all fittings,head shoes,bends,swan neck etc. Note: work is to be executed at any height and situation.

S & F PVC (SWR) pipes110 mm bore single socketed, in any length with rubber ring joints, laid in trenches or in floors/walls including fixing clamp etc. Note: work is to be executed at any height and situation.

Dismantling Wall and ceiling boards (fibre,pulp, insulation, etc.) orinsulation boards/slabs/blankets, any thickness, including cover fillets

S & F wall panelling 'Anutone-ACT KLH' Vinyl finish,Bevel edge of size 1200 x 1200 x 25 mm thick with glass fiber core,in rectangular grid of size 1200mm(H) x 1200mm(W) fixed on wall using galvanised steel 'Strul Z-Bar' or 'Impale clip' fixed to the wall in grid pattern all as per manufacturer instruction. NRC is upto 1.0 and fire class 'A'. Note:Contractor quotated rate shall be deemed to be inclusive of all minor items of exectution to complete the work as per manufacturer instructions.No price adjustment shall be done during execution if any item of work is specifically required to complete the work even if it is not mentioned in the description of Item above.

S&F False Ceiling 'Anutone-subtex Nubby' ceiling panel of size 1195 x 595 x 20 mm thick, texture finish concealed edge with glass fibre core fixed to T-grid ceiling frame work using galvanised steel 'Skelet Trelis' T 24 concell' system consisting of main tee MT 24 W 36 at 600 c/c and cross tee CT 24 W 12 at 1200 c/c,wall angle WA 24 W 30 around wall and spacer bar WA 24 W 30 at 600 c/c all as per manufacturer's instructions. Thickness of main/cross tee will be 0.3mm and that of wall angle/spacer 0.4mm. NRC is upto 0.90 and Fire class is I & P. Note:Contractor quotated rate shall be deemed to be inclusive of all minor items of exectution to complete the work as per manufacturer instructions.No price adjustment shall be done during execution if any item of work is specifically required to complete the work even if it is not mentioned in the description of Item above.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing debris out of MOD land and rubbish off the premises. Note:work to be executed at any height and situation.

M&L for 8-10 mm thick double charged vitrified tile 600 x 600mm as in flooring,laid in any shape/pattern over and including 15 mm thick screed in CM 1:6 as in floors. Note:shade of tile shall be as approved by GE based on manufacturing company catalogue. Note:work to be executed at any height and situation.

M&L for 8-10 mm thick double charged vitrified tile as in skirting,laid in any shape/pattern over and including 10 mm thick backing coat in CM 1:4. Note: skirting shall be of same size and same make as for flooring. Note:work to be executed at any height and situation.

Demolition of reinforced cement concrete of any description and in any position not specifically provided for and removing debris out of MOD land.

M&L for Precast cement concrete 1:2:4 type B-1(using 20mm graded aggregate) as in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces set in CM 1:4.

M&L for Mild steel TMT bars 6 to 8mm dia , cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips

NOTE : - AMOUNT OF SCHEDULE OF CREDIT RS. 89,820.00 WILL BE DEDUCTED FROM TOTAL AMOUNT OF BOQ.

M/S SAMEER SUBHASH PATANI (BID ID -3124333)

M/S R.K.S. CONSTRUCTION (BID ID -3124066)

Abhiraj Enterprises (BID ID -3122861)

MAHIMA CONSTRUCTION (BID ID -3132155)

MANOVANDANA CONSTRUCTION (BID ID -3132869)

Bidder Name

MAHIMA CONSTRUCTION

M/S SAMEER SUBHASH PATANI

J Sams Contructions

M/S R.K.S. CONSTRUCTION

Abhiraj Enterprises

MANOVANDANA CONSTRUCTION