CERTAIN SPECIAL REPAIR WORK UNDER GE WEST FEROZEPUR CANTT

Amount

Dismantling of brick tiles in roof single layer jointed & pointed in cement mortar including removal of grass vegitation including roots near outlet of RWP and OHT staging area or specifically ordered by Engineer -in -Charge in writing, complete all as specified.

Dismantling of brick tiles in roof double layer jointed & pointed in cement mortar including removal of grass vegitation including roots near outlet of RWP and OHT staging area or specifically ordered by Engineer -in -Charge in writing, complete all as specified.

Demolition of mud phuska in roofs, any thickness, including leeping plaster (whether full thickness removed or only a part thereof) complete all as specified.

M&L for 15mm thick screed in cement mortar (1:4) on brick/concrete of roof surface finished even and smooth without using extra cement etc complete all as specified.

M&L for screeding 10 mm in cement mortar (1:4) on brick/concrete roof surfaces, using WPC (WPC measured and paid separately), surfaces finished even and smooth without using extra cement etc complete all as specified.

M & L for 80mm thick average consolidated thickness mud phuska on flat roof ncluding 25mm thick mud plaster complete all as specified.

Polymer modified bituminous membrane 3 mm thick with sand witched polythene film/non woven polyster reinforcement /polymeric water proofing membrane 3Kg/sqm plastifelt/hyperplas /multiplas / shivam or equivalent ) laid over hot blown grade85/25@ 1.2kg/Sqm (i.e roof slab cleaned throughly to to remove all loose particle dust/dirt particle ) shall be laid over entire roof surface over 4kg/Sqm bituminous primer and on verticle surface up to grooves ( or as per manufacturers recommendation) with over laps of 100mm The over lap shall be sealed by flames or as per manufacturer instruction.Hot blown bitumen grade 85/25 @1.2kg/Sqm applied over the membrane should be compatible with membrane all as recommendation manufacturers and all as specified and directed.

Polythene film (transparent) 150 micron with 150mm end & side laps bonded with 80/100 bitumen and laid on roof, complete all as specified and directed.

M&L Cutting out cracks to V-Section in existing roofs or terracing cleaning out, wetting grouting with cement and sand slurry 1:3 complete all as specified and directed.

M&L for brushing neat cement slurry with 3 kg of cement per square metre

M&L preparation of roof surface and applying one coat of aluminium primer (reflux) @ 0.10 kg /m applied on treated bituminous membrane complete all as specified and directed.

M&L Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or etc., and making good, cutting not exc 10 cm girth

Removing mud phuska /soil material exc. 250 m but n exc. 500 m and depositing where directed

M&L for Cement concrete tiles 25cm x 25cm x 22mm thick, with grey cement and no pigment laid over 15 mm thick screed in CM (1:6) mixed with water proofing compound ,joints grouted and flush pointed in CM (1:3) mixed with 5% of crude oil by weigt of cement complete all as specified.

M&L 40 mm thick cement concrete 1:2:4 type B1 using 20 mm graded stone aggregate as in slope correction layer over RCC slab finished without using extra cement complete all as specified and as directed.

S&F 40 mm thick brick tiles laid over a layer of 25 mm thick mud mortar and joints grouted flush in cement mortar (1:3) mixed with 5% of crude oil by weight of cement, complete all as specified.

All as per item No 16 herein before but using old brick tiles retrieved from dismantling (Item No 01 hereinbefore) including cleaning and removal of mortar from tiles. complete all as specified.

Taking down cement plaster inlcuding racking out joints, hacking for keys, scrubing down with water, complete all as specified and directed.

M&L 10 mm thick rendering in cement mortar (1:6) on any face of brick walls or concrete surfaces, finished fair and even complete all as specified and directed.

M&L Rendering 15mm thick in cement mortar (1:4) on any face of brick walls or conrete surfaces, surfaces finished fair and even complete all as specified & directred.

M&L Rendering 5mm thick in cement mortar (1:3) on any face of brick walls or conrete surfaces, surfaces finished even and fair without using extra cement, in ceiling, soffits of chajja or similar location etc complete all as specified & directred.

M&L for Preparation of old treated plastered surfaces of walls after complete removal of existing treatment and applying two coats of cement base paint complete all as specified.

Preparation of newly plastered surfaces of walls and applyings two coats of cement base paint over a coat of primer complete all as specified and directed.

M&L for Washing, rubbing down and stopping of old treated distempered and painted surfaces of walls and applying one coat of cement base paint complete all as specified.

M&L Complete removal of existing treatment of wall suface and applying two coats of oil bound distemper, over a coat of wall care putty, complete all as specified and as directed.

M&L for White wash in one coat on old plastered surfaces of ceiling including preparation of surfaces complete all as specified..

M&L for White wash in two coats on old plastered surfaces of ceiling including preparation of surfaces complete all as specified..

Preparation of new plastered surface and applying two coats of oil bound distemper over a coat of primer complete all as specified.

M&L Preparation of newly plastered surfaces of wall and applying two coats of oil bound distemper, over a coat of 2 mm thick wall care putty, and a coat of primer, complete all as specified and as directed.

M&L washing rubbing down and stopping of distempered and painted surfacesand applying one coat of Oil Bound Distemper on wall surfaces including proper curing all as specified and directed.

M&L for Preparation of newly plastered surfaces of walls & applying three coats of white wash complete all as specified.

M&L for Preparation of newly plastered surfaces of ceiling & applying three coats of white wash complete all as specified.

M&L for Preparation of new steel surfaces of any description, over 10cm width or girth and applying two coats of synthetic enamel paint, complete all as specified.

M&L for Preparation of old steel surfaces of any description, over 10cm width or girth and applying one coats of synthetic enamel paint complete all as specified.

M&L for Preparation of new wooden or wood based surfaces of any description, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified.

M&L for Preparation of old wood or wooden surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint on already prepared old wooden surfaces complete all as specified and directed.

Taking down wooden chowkhats or frames with shutters (without taking off shutters from the frames) of size not exceeding 1.50 Sqm each including cutting holes in brick walls of appropriate size for insertion of cement concrete blocks for hold fasts complete all as specified and directed.

All as per item No 37 herein before but size exceeding 1.5 Sqm and not exceeding 4 Sqm each.

Taking down shutters of any description and refixing in the same opening exc 1 sqm and not exc 2 sqm each complete all as specified and directed.

S&F Factory made box type steel window side hung with pintol hinges & 2 Nos 150mm mild steel tower bolts to each shutter, steel handle and with glazing bars dovetailed or welded and with one shop coat of zinc chromate primer complete all as specified and shown on Drawing No CEJZ/TD-06/07 & CEJZ/TD-07/07.

S&F Factory made box type steel window side hung with pintol hinges & 2 Nos 150mm mild steel tower bolts to each shutter, steel handle and without glazing bars dovetailed or welded and with one shop coat of zinc chromate primer complete all as specified and shown on Drawing No CEJZ/TD-06/07 & CEJZ/TD-07/07.

S&F Factory made box type steel ventilator with glazing bars dovetailed or welded and with one shop coat of zinc chromate primer complete all as specified

S&F factory made 35mm thick second class hard wood plain framed panelled shutters (any number of panels ), with panels of timber flat on both sides (feather edge), or of veneered particle board medium density wood wood particle board with commericial face veneers and fitted to chowkats.

S&F factory made 35mm thick second class hard wood glazed and skelton shutters,open rebated and prepared to receive glass gauze,etc (without sash bars),edges of framing plain chamfered or rounded fitted with cut and mitred beads for securing glass etc sizes of members of shutters as specified in SSR part-I section 8 clause 8.24(a) fitted to chowkat.

S&F 150 mm Floor door stopper of aluminium alloy body and tongue, anodized with hard drawn steel spring complete all as specified and as directed.

PTMT tower bolts, 150 mm long and fixed with steel screws complete all as specified.

PTMT butt hinges,100mm long, fixed with steel screws with brass /bronze hinges pin complete all as specified and directed.

PTMT handle 150mm long fixed with steel screws complete all as specified.

Dismantling of floor hearth and wall tilling incl mortar beding removing serviceable tiles to store and rubbish off the premises as directed by the Engr-in-Charge

M & L for non skid coloured ceramic tiles of 7 to 8 mm thick , area of each tile exceeding 0.11 sq m but not exceeding 0.18Sq m in floors set and jointed in neat cement slurry and pointed in white cement mixed with colour pigment to match over a screed layer of 15 mm thick in CM 1:6 complete all as specified and as directed.

M & L for non skid coloured ceramic tiles of 7 to 8 mm thick , area of each tile exceeding 0.11 sq m but not exceeding 0.18Sq m as in skerting/dado set and jointed in neat cement slurry and pointed in white cement mixed with colour pigment to match and backing with 10 mm thick in CM 1:4 complete all as specified and as directed.

S/F of Glazed coloured and cereamic tiles in vertical surfaces 300X200X7mm / 450X300X7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over backing coat 10mm thick in cement mortar 1:4 for laying skirting dados and vertical surfaces all as specified and directed

Demoltion of brick work built in cement mortar of any specification and in any position complete all as specified.

Brick work in cement mortar 1:6 using sub class ‘B’ old size bricks, straight or curved on plan exceeding 6 metre mean radius complete all as specified.

All as per item 54 hereinbefore but using old bricks retrieved from demolition under item 53 hereinbefore including cleaning and removal of mortar from old bricks.

Solid PVC door frame of size 50 mm x 47 mm made of 5 mm plain colour PVC sheet reinforced with mild steel square tube complete all as specified in clause 8B.3.1 and shown on page 150 of MES Schedule Part-II (2004).

Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement, supply and fixing in the frame at site as per clause 8 B.2.1 of MES schedule Part-II (2004) complete all as specified. .

Hacking out old broken glass from metel frame including punching or drilling out old glazing pins/ spring clips and providing and fixing new complete all as specified and directed.

S &F in repair to 3mm thick, plain sheet glass ordinary quality and glazing, with oil putty or with wooden beads, in squares n.exc 0.50 Sqm incl. incl hacking out old broken glass and putty/beading complete all as specified.

3mm thick, plain sheet glass ordinary quality and glazing, with oil putty or with wooden beads (supplied alongwith shutters), in squares n.exc 0.50 Sqm complete all as specified.

Removing & refixing of existing water tank of capacity 500/250 Ltr etc setting aside (or lowering if required) for repair, cleaning etc and hoisting reconnecting & refixing in position.

S&F Forming jambs etc built in cement mortor 1:6 to openings incl cutting toothing and properly bonding into to old work also facing ,jointoing and pointing to match to existing work complete all as specified.

S &F in repair Galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture not more than 1.18mm and fixed with tinned tacks or galvanized wire staples complete all as specified as in repair.

Galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture not more than 1.18mm and fixed with tinned tacks or galvanized wire staples complete all as specified.

S&F Extruded Aluminium alloy tower bolt of 200mm length of bolt and fixed with screws, complete all as specified.

S&F 100mm size Butt hinges, medium weight, cold rolled mild steel complete all as specified and directed.

S&F 150mm size, extruded aluminium alloy handles, fabricated type, anodized and fixed with screws complete all as specified.

S&F 150mm long aluminium, anodised barrel tower bolts of extruded section, all as specified and as directed by the Engr-in-charge.

S&F 150 mm size, aluminium (cast type) anodized, handle and fixed with screws complete all as specified.

S&F 300mm Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified.

S & F 250mm long mild steel, sliding door bolt, plate type, stove enameled black, with bright bolt not less than 12mm dia with and including bolts and nuts complete all as specified.

S&F 300 mm Mild steel helical door spring including roller and roller plate complete all as specified.

Hasp and staple of aluminium anodized, safety type, 100mm long, fixed with screws complete all as specified.

Continuous (piano) hinges, mild steel bright finish or electro galvanised with flap (when open) 40 mm, fixed with steel screws complete all as specified.

S&F galvanised steel water tubes 15 mm bore medium grade, with all fittings and fixed complete to walls and ceiling or laid in floors including taking down corroded GI pipe complete all as specified and as directed by Engr-in-Charge.

S&F galvanised steel water tubes 20 mm bore medium grade, with all fittings and fixed complete to walls and ceiling or laid in floors including taking down corroded GI pipe complete all as specified and as directed by Engr-in-Charge.

Taking up or down 15 mm existing steel tubing and connections and re fixing old steel tubing and connections in new or old position complete to walls and ceiling or laid in floors complete including cleaning the steel tubing all as specified and as directed.

All as per item No. 77 here in before but 20mm dia.

S&F 1000 litres capacity rotational moulded, triple layer polythene water storage tanks (cylindrical vertical with closed top) hoisting and fixed in position on roofs including fittings & dismantling existing water storage tank, complete all as specified.

S&F 500 litres capacity rotational moulded, triple layer polythene water storage tanks (cylindrical vertical with closed top) hoisting and fixed in position on roofs including fittings & dismantling existing water storage tank, complete all as specified.

S&F in repair 20mm bore PTMT ball valve high pressure with polythene float and fly nut complete, screwed for iron pipe or brass ferrule and fixed, complete all as specified.

S&F 1mm thick stainless steel sink, plugs, washers, PVC waste pipe, union, CP coupling & cantilever brackets embedded in cement and sand mortar in wall , overall size of sink 495mmx420mm, bowl size 410mmx330mmx 160mm as in repair complete all as specified.

S&F 1mm thick stainless steel sink, plugs, washers, PVC waste pipe, union, CP coupling & cantilever brackets embedded in cement and sand mortar in wall , ovesinks with drainage board made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mmrall size of sink 495mmx420mm, bowl size 410mmx330mmx 160 mm as in repair complete all as specified.

S&F stainless steel plate rack of standard pattern & of size 900x900x250mm thickness of stainless steel sheet shall be 304 AISI including fixing to wall with 4 nos 50 mm screws & pvc rawl plugs complete all as specifed and directed.

S&F PVC Connection pipe (LDPE) of pressure rating 6 Kg per Sq.cm, 450mm long, heavy duty with two sets of brass nuts & washers (one at each end)etc suitable for 15mm bore of pipe as in repair complete all as specified.

S&F Soap dish of PTMT fixed to wall with steel screws and PVC rawl plug complete all as specified.

S&F Vitreous china white squatting pan orrissa pattern of size 580mm x 440 mm with integral foot rests including necessary lime concrete and 100 mm bore cast iron ‘P’ trap with 550 to 600 mm long neck for connecting WC to branch piece with cement joints, fixed as in repair, complete all as specified.

S&F PVC low level flushing cistern (white) of 10 liters capacity with inlet ball float valve, PVC flush pipe and necessary fixing arrangements and connecting to water pipe and WC etc complete all as specified.

S& F Vitreous china wash down water closet pan ( pedestal pattern) white ( Excluding fixing bolts , flushing cistern and flush pipeall as specified and directed.

S & F Wash hand basin, flat back 550x400mm vitreous china (white) including PTMT waste fittings, 32mm bore size, waste pipe, PVC, 32mm bore, angle iron/cast iron brackets of required size as directed & making good disturbed surfaces to match with the existing complete all as specified and directed.

S&F Mild steel curtain rod powder coated with fixing side brackets, end cups, rings @ 10 Nos per RM and fixed with PVC rawl plugs & steel screws as in repairs complete all as specified.

Dismantling CI pipe alongwith fittings of 50/75/100mm dia, below or above ground level or laid in floors, jointed in cement mortar and taking out complete all as specified.

Taking down eaves gutters and rainwater pipes(any size or pattern), including all fittings, heads, shoes, bends, swan-necks etc.

S&F 110mm dia PVC (SWR) pipes (pressure rating not less than 4 Kg/cm2) single socketed in any length with rubber ring joints, fixed to wall complete all as specfied and directed.

S&F 110mm bore, PVC (SWR) bends any radius complete all as specified.

S&F PVC (SWR) vent cowl, for 110mm bore pipe complete all as specified.

S&F 110mm bore, PVC (SWR) branch piece, single (single T) equal or unequal with access door complete all as specified.

S&F 75mm bore PVC (SWR) pipes (pressure rating not less than 4 Kg/cm2) single socketed, in any length with rubber ring joints, fixed to wall complete all as specified and directed.

S&F 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors, complete all as specified and directed.

S&F 75mm bore, PVC (SWR) bends any radius complete all as specified.

S&F 75mm bore, PVC (SWR) branch piece, single (single T) equal or unequal with access door complete all as specified.

S&F 75mm bore PVC (SWR) floor trap, plain with grating including jointing with solvent cement as in repairs complete all as specified.

S&F bib taps 15mm bore, cast copper alloy with crutch or butterfly handle, screwed down screwed for iron pipe or for brass ferrule all as specified.

S&F 15mm stop valve cast copper alloy with crutch or butterflty handle, screwed down for iron pipe or brass ferrule fancy type chromium plated with long shank and cup.

S&F 15mm stop cock/angle cock cast copper alloy with crutch or butterflty handle, screwed down screwed for iron pipe or for brass ferrule fancy type chromium plated with fancy shank and cup all as specified.

S&F 15mm bore pillar tap, cast copper alloy, with capstan heads, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly-nuts, screwed for iron pipe,

S & F 125mm dia CP grating doom fixed over trap with cement complete all as specified and directed

S&F towel rail 600mm long fixed with and including chromium plated brass screws and wooden/plastic cleats (Min wt 190 gms)

Supply & fixing in repair 125 mm chromium plated shower rose with or without swivel joints any size including fixing to steel pipe or union.

Demolition of cement concrete of any description and in any position not otherwise specifically provided

M&L 15 mm thick CM (1:4) as in horizontal and vertical surface of sunken floor portion and mix with SIKACIM (liquid integral water proofing admixture) of ratio 100 gm per cement bag(50 kg) add with 23 ltr of water and all as specified and directed.

M & L for applying evenly a tack coat of Industrial Bitumen 85/25 at the rate of 1.2 Kg per sqm incl cleaning surfaces as specified & directed by the Engr-in-Charge.

M&L Cement concrete (1:2:4) type B-1 (20 mm graded stone aggregate) as in roof kerbs or mud stops, bed blocks, benching,copings etc including form work, weathering, slightly rounded or chamfered complete all as specified.

M&L Cement concrete type E-2 1:5:10 in 40 mm graded aggregate as in sunken floor filling

M&L 30 mm thick cement concrete 1:2:4 type B1 using 20 mm graded stone aggregate mixed with water profing compound 3% of cement content as in flooring complete all as specified and as directed.

M&L Cement concrete (1:2:4) type B-1 using 20 mm graded stone aggregate as in plinth protection, 50mm thick, surfaces finished even and fair without using extra cement as in plinth protection including provision of construction joints complete all as directed by Engr-in-Charge and as specified.

S&F factory made Pressed steel frames made of 1.25mm thick MS sheet of profile 105x60mm for door and window frames with one rebate including lock strike plate, shock absorber, 20mm dia 60mm long MS conduit for housing of a drop bolt, treating of internal surfaces of chowkhats with coal tar or black paint including hinges, hold fasts/lugs etc complete all as specified.

All as per item above 118 here-in-before but size 125x60mm with double rebate.

All as per item above 118 here-in-before but size 75x50mm with single rebate.

Demolition of boarding of any description and in any position complete all as specified.

S & F 14 to 16 mm Solid PVC board plain colour ,fixed with screws or adhesive with complete accessaries as in shelves with rebates fixed on PVC solid pattern of size 40mmx18mmx500mm on tree sides n complete including taking down as fixed in repairs all as specified and directed.all as spd and directed by Engineer in charge.

M & L PCC (1:2:4), type B-0 using 12.50mm graded stone aggregate as in filling of steel chowkhats complete all as specified.

M&L for PCC1:3:6 type C-2(40mm graded aggregate)as in posts etc all as specified.

M&L Cement concrete (1:3:6), type C-1 using 20mm graded stone aggregate as in filling of steel chowkhats including necessary form work complete all as specified.

Demolition reinforced cement concrete ( reinforcement cut as required to facilitate demolition) of any description and in any position not otherwise specifically providedand removing the debris out side MD land complete all as specified and directed.

Demolition of Stone slabs and tiles laid bedded pointed in mortar of any description or thickness in floors, aprons etc.

M & L marble slab, 16-18mm thick of size not less than 1 Sqm each, machine cut as cooking platform or in any position, set and bedded in gray cement slurry over & including 15mm thick screed in cement mortar (1:4) and pointed in white cement with admixture of pigment to match the shade of granite including cutting, polishing (mirror type) complete all as specified.

M&L Plain cement concrete (1:4:8) type D-2 (using 40mm graded stone aggregates) 75mm thick as in sub base of floor complete all as specified & directed.

M&LCement concrete (1:2:4) type B-1 using 20mm graded stone aggregate as in plinth oprotection, sub base etc 50mm thick, surfaces finished even and smooth without using extra cement complete all as specified.

M&L Machine cut kota stone slab flooring 18-22mm thick over 20 mm cement screed base CM 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing polishing and rounded or chamfered for nosing complete all as per specified

M&L Kota stone slab 12-15mm thick in riser of steps, skirting, dado and pillar laid over 15 mm thick rendering (1:4) and jointed with ditto as per above item no 102

Demolition of un-reinforced cement concrete in ground floor and paving not exceeding 15 cm thick (below or above ground level) complete all as specified.

M&L Hardcore with broken bricks of guage n. exc 63mm deposited, spread and levelled in layers n exc. 10 cm thick, watered and rolled/ rammed to a true surface

M&L for 100mm thick Plain cement concrete (1:4:8) type D-2 using 40mm graded stone aggregate as in sub base complete all as specified and directed.

S & F 1.00 mm thick mild steel ,plain sheet in gates and similar work cut to size ,holes punched including round headed screws clout nails or rivits and fixed to steel framing with plain 40 mm lap joints with rivited or welded incl bending or turning up etc all as specified and directed

Mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips all as specified and directed

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning,filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm,all as specified and directed

M&L PCC (1:3:6) type C2 using 40mm graded aggregate as in foundation filling and mass concrete complete all as directed.

Dismantling posts or struts (wood, steel or R.C.C.) any section, including taking out embedded portion and making good disturbed ground ,all as specified and directed

S&F rolled mild steel structural work as in posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc. and similar work conforming to Fe-290 Gde E-165

Dismantling fencing wire mesh any type including plain bars and MS flats including nut and bolts/rivets complete all as specified and directed.

Supply only Chain link MS galvanisd fencing made of 3.15 mm dia wire and 50mm X 50mm mesh.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provission of binding wire complete all as specified and directed.

S&F Galvanised. 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type ofstandard rails strain- ing bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured) complete all as specified and directed.

Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or squarenut, n exc 5cm long diameter of neck 11 to 15 mm complete all as specified and directed.

M&L 60mm thick Coloured (Yellow & red) interlocking (M-35) cement concrete tiles of approved design & pattern with grey cement and pigment laid over Complete all as speciifed and directed.

Sand filling under floors or in foundations including watering and consolidation

Cutting holes in brick walls exc half bricks but not exc one brick built in cement mortar or cement lime mortar and stone walls built in lime mortar

Dismantling structural steel work framed truss etc.

S&F framed work as in roof trusses, purlins, crane gantries, rails and fastening and heavy bracket framing (beam, teel, angle, channel or flat section) including distance pieces, cleats etc conforming to Fe 290 (Gde E-165)

Dismantling plain or corrugated sheet/fibre sheet on roof covering complete all as specified and directed.

S&F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

Dismantling of wall and ceiling boards (Fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets complete all as specified.

S & F in rep of Gypsum Board 8mm thick in ceiling fixed with screw 60x60cm placed in ceiling (Angle 25mm X 25mm , Main tee 38mmX23mm ,Sub tee 23mmX23mm) incl aluminium anodised snap grid frame 605X605 mm for false ceiling incl hanging arrangement complete all as specified and directed by Engineer in Charge.

Surface excavation not exc 30 cm deep averaging 15 cm deep and getting out in hard dense soil.

Taking down carefully copper /aluminium point wiring (light, fan , socket or power ) complete, fittings such as switches, ceiling roses, pendants, regulators sockets light fitting etc removing materials to store for keetping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls , floors ,etc.

M &L Point wiring complete with 1100 volts grade PVC insulated unsheathed FRLS cable of copper conductor, multi stranded of size 1.5 sqmm, single core, in and including existing rigid non-metallic PVC conealed conduit, with all accessories if require such as bends,reducers, spacers, saddles, junction boxes bakelite sheets, wooden rectangular boards / round blocks(for housing lamp holders and light fittings etc) and existing MS pressed steel / cast iron sunken boxes of suitable size for mounting switches / bell pushes / sockets, fan regulator etc covered with new 3 mm thick laminated bakelite sheet top cover including continuous earth wire of size 1.5 sqmm unsheated stranded copper conductor with green PVC insulation connected to common earth dolly complete all as specified and directed for the followings :- (a) One light/fan Point controlled by one single pole one way switch.

(b) One socket outlet on the same board controlled by one single pole one way switch

(c) One 5 amps socket outlet independent controlled by one single pole 5 Amp switch.

All as per Item No 158 mentioned here-in- before but one three pin 15 Amps switch socket out let on the independent board with 2.5 Sq mm PVC insulated copper conductor and 2.5 Sqmm copper conductor for continuous earthing complete.

Supply & Fixing Switch piano flush type single pole one way 5/6 Amp complete all as directed.

Supply & Fixing Switch piano flush type 15 amps, single pole one way duly ISI marked.

Supply & Fixing Socket outlet 2 in one , 5/6 Amps flush type ISI marked.

Supply & Fixing Socket outlet, 2 in one 6 pin 5 and 15 Amps piano flush type ISI marked.

Supply & Fixing ceiling rose,PVC/Polycarbonate,isolated three terminals.

Supply & Fixing bell push flush type 5 Amps duly ISI marked.

Supply & Fixing bell ding dong type AC 230 Volt single pole.

Supply & Fixing step type regulator Piano switch type ( 5 step) for ceiling fan 1200/1400 mm size 230 volts, 6 Amps.

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified.

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300m

Supply & Fixing Lamp holder PVC/Polycarbonate,isolated with back plate suitable for batten fittings including 10W LED Bulb omplete all as specified and directed.

Supply & Fixing sheet metal enclouser double door factory made powder coated out of CRCA mild steel sheet 1.2 mm thick wih metallic painting white series TPN DBs (Vertical type)fitted with ABS frame and 415 volts 200 Amps rated enameled bus bar 4 way dust and vermin proof ssuitable for incorporation of MCBs duly concealed in wall and making good to distrubed surface and colour matching complete all as specified

Supply & Fixing sheet metal enclouser double door factory made powder coated out of CRCA mild steel sheet 1.2 mm thick wih metallic painting white series pre-wired SPN DBs, 240 volts 200 Amps rated bus bar,Neutral link,Earth bar and Din rail, 8 way dust and vermin proof suitable for incorporation of MCBs duly concealed in wall and making good to distrubed surface and colour matching complete all as specified.

All as item No 174 above but DB's 4 way.

Supply & Fixing MCCB 100 Amps, 415 volts, 16 KA, 4 Pole complete all as specified.

Supply & Fixing MCCB 63 Amps, 415 volts, 16 KA, 4 Pole complete all as specified.

Supply & Fixing MCB, Single Pole and neutral 240 V, 32 Amps 10 KA 'B' series.

Supply & Fixing MCB, Single pole 240 V,6 - 32 Amps 10 KA 'B Series.

Supply & Fixing LED tube light fitting 18 Watts,4 feet long decorative ultra slim linear LED lighting fixture with extruded polycarbonate,environmental friendly, energy efficient 230V, complete with all accessories internally pre wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size. Cat Part No LCTL-18-CDL of Make : Crompton or equivalent to Havells/Bajaj/Phillips.

Supply & Fix in repair sub main wiring of 4 sqmm PVC insulated unsheathed FRLS cable multistranded copper conductor with earth wire of 4.0 sqmm PVC insulated unsheathed FRLS cable multistranded copper conductor including PVC conduit pipe 25 mm dia all as specified and directed. Note:-Two run of single core 4 sqmm cable and one run single core 4.0 sqmm cable for earth wire and including conduit pipe 25 mm dia shall measured as one length).

All as per item No 181 above but 6 Sqmm submain wiring

Earthing complete with Copper plate elecrode of size 60 cm x 60cm x 3.15 mm thick burried directly in ground vertically to a depth not less than 2.5 mtr below the ground level with top edge of earth plate at a depth not less than 1.5 mtr below ground level. Earth plate surrounded by 15mm thick packed alternative layers of charcoal dust and comman salt, earth lead copper srtip 20x3 mm by means of bolts , nuts, check nuts and washers of galvanised iron with thimbles. The other end of GI earth wire is connected to main switch board and protected by light grade GI pipe of 15 mm bore. provision of 20mm bore light grade GI pipe for watering including GI funnel and wire mesh. Pipe shall be provided vertically upto top level of earth pit and then taken horrizontally to the earth pit. Cement concrete chamber of PCC ( 1:3:6 ) type C-2 using 40 mm graded stone aggregate.The chamber shall be constructed one metre away from edge of earth pit. 50 mm thick pre cast cover of cement conrete (1:2:4) type B-1 using 20 mm graded stone aggregate, excavation in soft / loose soil, returning filling and removal of surplus soil to a distance of 50 mm as directed and shown in Electrical Plate No- 3 of SSR Part-1 (2009)

Earthing complete with galvanized steel plate elecrode of size 60 cm x 60cm x 6.0 mm thick burried directly in ground vertically to a depth not less than 2.5 mtr below the ground level with top edge of earth plate at a depth not less than 1.5 mtr below ground level. Earth plate surrounded by 15mm thick packed alternative layers of charcoal dust and comman salt, earth lead GI wire of 4mm dia (8 SWG) by means of bolts , nuts, check nuts and washers of galvanised iron with thimbles. The other end of GI earth wire is connected to main switch board and protected by light grade GI pipe of 15 mm bore. provision of 20mm bore light grade GI pipe for watering including GI funnel and wire mesh. Pipe shall be provided vertically upto top level of earth pit and then taken horrizontally to the earth pit. Cement concrete chamber of PCC ( 1:3:6 ) type C-2 using 40 mm graded stone aggregate.The chamber shall be constructed one metre away from edge of earth pit. 50 mm thick pre cast cover of cement conrete (1:2:4) type B-1 using 20 mm graded stone aggregate, excavation in soft / loose soil, returning filling and removal of surplus soil to a distance of 50 mm as directed and shown in Electrical Plate No- 3 of SSR Part-1 (2009)

Supply and fixing LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete. complete all as specified and directed.

Supply and fixing post top lantern LED type 20 watt 230 watt volts AC outdoor type with decorative post top for 360 degree indirect light IP 65 protection with impact and corrosion resistant complete with driver and lamp complete

Supply & Fixing LED bulb 10 Watt complete all as specified and directed.

Supply and fixing LED street light fitting 60 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete. complete all as specified and directed.

Supply and lay cable XLPE insulated screened PVC bedded, galvanised steel strip or wire armoured, electric power cables (Heavy duty) 1100 volts grade with stranded aluminium conductor of size 25 Sqmm 4 core.

Supply and lay cable XLPE insulated screened PVC bedded, galvanised steel strip or wire armoured, electric power cables (Heavy duty) 1100 volts grade with stranded aluminium conductor of size 16 Sqmm 2 core.

Suplying and fixing 1100 volts grade heavy duty10 Sq mm two core cable PVC insulated aluminium conductor, served with inner shething of PVC sheeathed in service conections suspended by insulating hangers not more than I metre apart including 4Sq mm suspension wire, one twin core cable flat or circular

M & L Air termination single pointed copper rod 12mm dia and 300mm long complete all as specified.

M & L Copper iron strip 32x6mm buried directly in ground or fixed to walls complete all as specified and directed.

M & L for Test point terminal block made of gun metal or phosphorous or bronze size 75x75x25mm drilled and screwed including 3 Nos, 8mm dia 25 mm long hex head screw complete all as specified and directed.

Excavation in trenches n.exc 1.5 m wide and n.exc depth in loose/soft soil and getting out for laying of cable and reection pole.

Returning filling in including spreading leveling watering and well ramming in layers n. exc 25 cm in soft/loose soil complete all as directed

Removal of excavated soil n.exc 50m and depositing where directed at a level n.exc 1.5 m above the starting point complete all as per directed

M&L for sand filling under floors, foundation or cable protection including spreding leveling in layer not exc 25cm thick.

M & L sub class B bricks locally available of size 22x11x7.5 cm laid dry width wise acrose the line of cable in trenches for protection of UG cable

M&L Mild steel galvanised iron pipe light grade (ISI marked) 40mm bore for passing of cable laid in trenches fixed to walls laid under floors, roads including all fittings i.e MS clamps nuts & bolts etc as required all as specified.

M & L Mild steel galvanised iron pipe light grade (ISI marked) 50mm bore for passing of earth lead laid in trenches fixed to walls laid under floors, roads including all fittings i.e MS clamps nuts & bolts etc as required all as specified.

M/s Sanjiv Kumar

M/S Pee Kay Builders

R.S.ENTERPRISES

M/S Yashpaul Gulati

Sethi and Company

M/s Bansi Lal

S S BUILDERS