Renovation or upgradation works at MS Block-I (Fan Type) B wing quarters in CSIR-CLRI Staff Quarters, Adyar, Chennai-600020

Amount

Civil Part

Demolishing lime concrete/other sunken filling light weight concrete manually/ by mechanical means including roof tile and disposal of material within 50 metres lead as per direction of Engineerin- charge.

Demolishing cement concrete/Mosaic flooring manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)

Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge.

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. In cement mortar

Taking out doors, windows and clerestory window shutters (steel or wood) including stacking and refixing the same with SS Hinges etc complete as per the direction of engineer-in-charge. Of area 3 sq. metres and below

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking in departmental stores : Of area 3 sq. metres and below

Dismantling of flushing cistern of all types (C.I./PVC/Vitrious China) including stacking of useful materials near the site and disposal of unserviceable materials within 50 metres lead.

Dismantling old plaster including wall tile or skirting raking out joints and cleaning the surface for plaster including wall tile/ granite wall cladding and disposal of rubbish to the dumping ground within 50 metres lead.

Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved.[ rubbish to be taken out of the CLRI campus at the risk and cost of the contractor]

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:5:10 (1 cement : 5 coarse sand (zone-III) derived from natural sources : 10 graded stone aggregate 40 mm nominal size derived from natural sources)

Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, excluding the cost of centering,shuttering and finishing:1:2:4 (1 Cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)

Brick work with common burnt clay modular bricks of class designation 7.5 in foundation and plinth in:Cement Mortar 1:6 (1 cement : 6 coarse sand).

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to all floor level in all shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand)

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to all floor level. Cement mortar 1:4 (1 cement :4 coarse sand)

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Raj Nagar Plain white marble/ Udaipur green marble/ Zebra black marble. Area of slab over 0.50 sqm

Providing wood work in frames of doors, windows, cubbord,clerestory windows and other frames, wrought framed and fixed in position including dash fasteners of required dia & length as per the direction of Engineer-in-charge. Second class teak wood

Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete.

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws, one coat of wood primer and wooden putty etc complete

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 25 mm thick (for cupboard) including ISI marked nickel plated bright finished SS. piano hinges and locking arragement with necessary SS screws, one coat of wood primer and wooden putty etc complete

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured).

Extra for cutting rebate in flush door shutters (Total area of the shutter to be measured).

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (including fixing accessories such as nuts, bolts, fasteners etc.). Make:Jindal or equivalent

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level.Thermo-Mechanically Treated bars of grade Fe-500D or more.

Centering and shuttering including strutting, propping etc. and removal including edge upto 20cm wide of form for Suspended floors, roofs, landings, balconies and access platform

Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources).

Providing and fixing curtain rods of 1.25 mm thick chromium plated brass plate, with two chromium plated brass brackets fixed with C.P. brass screws and wooden plugs, etc., wherever necessary complete : 20 mm dia

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved zinc steel primer all complete.Fixed to openings /wooden frames with rawl plugs screws etc.[Note: fabrication to be done at site]

Providing and fixing special quality bright finished brass cupboard or ward robe locks with four levers of approved quality including necessary screws etc. complete.50 mm [Make:Godrej or equivalent]

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete :250x16 mm

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : 300x16 mm

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 300x10 mm

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 250x10 mm

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete :200x10 mm

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : 125 mm

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.Twin rubber stopper

Providing and fixing chromium plated brass night latch and lock of approved quality including necessary screws etc. complete. Make:Godrej or equivalent

Providing and fixing wire gauge shutters using stainless steel grade 304 wire gauge with wire of dia 0.5 mm and average width of aperture 1.4 mm in both directions for doors, windows and clerestory windows with necessary screws and one coat of wood primer:30 mm thick shutters.[Frame work of mesh shutters to be not less than 150mm wide] With ISI marked stainless steel butt hinges of required size , one coat of wood primer and wooden putty etc. Second class teak wood

Providing and fixing factory made uPVC white colour casement/ casement cum fixed glazed windows comprising of uPVC multichambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated) casement handles, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant inside/polyurathene sealent out side (polyurethane sealent paid separately) over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. Casement window single panel with S.S. friction hinges (300 x 19 x 1.9 mm), made of (small series) frame 47 x 50 mm & sash 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glass pane glazing bead of appropriate dimension. [Note:The rate are including scaffolding, Silicon sealent and power supply both should be apply the contractor.] Make: Fenesta or equivalent.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including corner beeding and pointing in white cement mixed with pigment of matching shade complete. Make: Kajaria or equivalent.

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including pointing the joints with white cement and matching pigment etc., complete.[ Non slippery/good matt finish as approved by engineer-in-Charge] Make: Kajaria or equivalent.

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.Double charge vitrified tile polished finish of size.Size of Tile 600 x 600 mm. Make:Kajaria or equivalent

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joint with white cement & matching pigments etc. complete.Size of Tile 600x600 mm Make: Kajaria or equivalent.

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete.

15 mm cement plaster on rough side of single or half brick wall of mix: (Note: approved River sand to be used) 1:6 (1 cement: 6 coarse sand)

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete. (Two coats)

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface : Water thinnable cement primer

Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate epoxy priming coat, preparation of surface, etc. complete.On steel work

Painting with oil type wood preservative of approved brand and manufacture :New work (two or more coats)

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture. Make:Berger or equivalent

Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour. Two coats. Make: Asian royale shine or equivalent)

Providing 40x5 mm flat iron hold fast 400 mm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 300x100x150 mm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size).including cutting of wall and making good the same.

Removing dry or oil bound distemper, water proofing cement paint and the like by mechanical scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete.

Fixing chowkhats in existing opening including embedding chowkhats in floors or walls cutting masonry for holdfasts, embedding hold fasts in cement concrete blocks of size 15 x 10 x 10 cm with cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size), painting two coats of approved wood preservative to sides of chowkhats and making good the damages to walls and floors as required complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in-Charge.Door chowkhats

Providing and fixing double scaffolding system (cup lock type) on the exterior side, up to seven story height made with 40 mm dia M.S. tube 1.5 m centre to centre, horizontal & vertical tubes joining with cup & lock system with M.S. tubes, M.S. tube challies, M.S. clamps and M.S. staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for the required duration as approved and removing it there after .The scaffolding system shall be stiffened with bracings, runners, connection with the building etc wherever required for inspection of work at required locations with essential safety features for the workmen etc. complete as per directions and approval of Engineerin- charge .The elevational area of the scaffolding shall be measured for payment purpose .The payment will be made once irrespective of duration of scaffolding.

Repair to plaster of thickness 12mm to 20 mm in patches of area 2.5 sqm and under, including cutting the patch in proper shape, raking out joints and preparing plastering the wall surface with cement based polymer modified self curing mortar (equivvalent to SP-40 or same), including disposal of rubbish, all complete as per the direction of Engineer-In- Charge.

Cutting holes of required size in brick masonry wall for fixing of exhaust fan including providing and fixing 300 mm dia PVC pipe conforming BIS-12818 and making good the same etc. complete as per direction of Engineer-in-charge.

Dismantling W.C. Pan/kitchen sink/washbasin of all sizes including disposal of dismantled materials i/c malba all complete as per directions of Engineer-in- Charge.

Taking out existing wooden door shutter, repair by cutting, painting etc. and refixing of repaired door shutters to existing door frames, including replacement of SS hinges with screws, etc. as required, all complete as per the direction of the Engineer-in-charge.

Dismantling of C.I. sluice valve including dismantling chamber and stacking of useful materials within a lead of 50 metres.Up to 150 mm diameter

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid. Make: Parryware or equivalent.

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Flat back wash basin size 550x400 mm with single 15 mm C.P. brass pillar tap jaguar or equivalent) Make: Parryware or equivalent.

Providing and fixing Stainless Steel A ISi 304 (18/8) kitchen sink as per IS: 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : Kitchen sink with drain board. 510x1040 mm bowl depth 250 mm

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Flexible pipe 32 mm dia

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Flexible pipe 40 mm dia

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick waterproofing hard board background fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete.Make:Jauguar or equivalent

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with G.I spl. clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall. 25 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 20 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with G.I spl. clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall. 50 mm nominal outer dia Pipes

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 25 mm nominal bore Make: Zoloto or equivalent

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :50 mm nominal bore. Make:Zoloto or equivalent

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :80 mm nominal bore.Make:Zoloto or equivalent

Providing and fixing uplasticised PVC connection pipe with brass unions for hot water supply : 45 cm length. 15 mm nominal bore. Make: Jaguar or equivalent

Providing and fixing C.P. brass shower rose with arm 15 or 20 mm inlet :Make: Jaguar or equivalent 150 mm diameter Make: Jaguar or equivalent

Providing and fixing C.I. sluice valves (with cap) complete with bolts, nuts, rubber insertions etc. including tail pieces if required :100 mm diameter.Class II.Make Kirloskar or equivalent

Constructing masonry Chamber 900x600x120/90 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for water meter complete with C.I. double/single flap surface box 400x200x200 mm (inside) with locking arrangement and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) , i/c necessary excavation/dismantling roof tile, foundation concrete 1:5:10 ( 1 cement : 5 fine sand:10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design :With common burnt clay F.P.S.(non modular) bricks of class designation 7.5

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 15 mm nominal bore Make: Jaguar or equivalent

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. 15 mm nominal bore Make: Jaguar or equivalent

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 15 mm nominal bore Make: Jaguar or equivalent

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931. 15mm nominal bore Make: Jaguar or equivalent

Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of Engineer-in-charge.

Providing and fixing PTMT grating of approved quality and colour. 100 mm nominal dia

Providing and fixing PTMT grating of approved quality and colour. Circular Type 125 mm nominal dia with 25 mm waste hole

Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms.

Cutting holes up to 15x15 cm in R.C.C. floors and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including finishing complete so as to make it leak proof.

Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs for all floor level, balconies, terraces etc consisting of following operations: (a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. (b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin- charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin- charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs. (c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge. (d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep. (e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test.“All above operations to be done in order and as directed and specified by the Engineer-in-Charge :With average thickness of 120 mm and minimum thickness at khurra as 65 mm.[Note: Shifting of materials not allowed through liftt machine provided for occupants. separate arragement may be made by the contractor at his risk and cost without disturbing the occupants. approved river sand to be used]

Providing and applying fibre reinforced elastomeric liquid water proofing membrane with resilient acrylic polymers/polyurethane having Sun Reflectivity Index (SRI) of 105 on top of concrete roof in three coats @10.76 litre/ 10 sqm. One coat of self-priming of elastomeric waterproofing liquid (dilution with water in the ratio of 1:1) and two coats of undiluted elastomeric waterproofing liquid (dry film thickness of complete application/system not less than 500 microns). The operation shall be carried out after scrapping and properly cleaning the surface to remove loose particles with wire brushes, complete in all respect as per the direction of Engineer-in Charge.Make:Fosroc Nito 725 or equivalent Methodology of applications: 1.First coat 1:1 (one part water : one part of polyurathane mix) properly mixed with stirring machine. 2.After 4 hours the second coat will be applied without water. 3.Third coat will be applied after 4 to 6 hours and allow for drying 48 hours 4.Roof will be tested with flood of water with minimum of 50mm level of water. 5.if any leakage found it will be addressed and again it is filled with water untill leakage arrest.

Providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing treatment to the RCC structures like retaining walls of the basement, water tanks, roof slabs, podiums, reservior, sewage & water treatment plant, tunnels / subway and bridge deck etc., prepared by mixing in the ratio of 5 : 2 (5 parts integral crystalline slurry : 2 parts water) for vertical surfaces and 3 : 1 (3 parts integral crystalline slurry : 1 part water) for horizontal /vertical surfaces and applying the same from negative (internal) side with the help of synthetic fiber brush. The material shall meet the requirements as specified in ACI- 212-3R-2010 i.e by reducing permeability of concrete by more than 90% compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline slurry shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the engineer-in-charge. The product performance shall carry guarantee for 10 years against any leakage.For vertical surface two coats @ 0.70 kg per sqm. Product- Fosroc or approved equivalent

Providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing treatment to the RCC structures like retaining walls of the basement, water tanks, roof slabs, podiums, reservior, sewage & water treatment plant, tunnels / subway and bridge deck etc., prepared by mixing in the ratio of 5 : 2 (5 parts integral crystalline slurry : 2 parts water) for vertical surfaces and 3 : 1 (3 parts integral crystalline slurry : 1 part water) for horizontal /vertical surfaces and applying the same from negative (internal) side with the help of synthetic fiber brush. The material shall meet the requirements as specified in ACI- 212-3R-2010 i.e by reducing permeability of concrete by more than 90% compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline slurry shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the engineer-in-charge. The product performance shall carry guarantee for 10 years against any leakage.For horizontal surface one coat @1.10 kg per sqm. Product- Fosroc or approved equivalent

Providing, erecting, maintaining and removing temporary protective screens made out of specified fabric with all necessary frame work,fixing, fittings arrangement to ensure that it remains in position for the work duration as required by the Engineer-in-charge.Wooven PVC cloth [Note: Building covered surface area will be measured for payment. required distance to be maintained from the wall as per the instruction of site incharge. Cloth sample as approved by the Engineer- in-charge. No extra will be paid in this regards]

Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., kitchen and the like consisting of: (i) Ist course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound conforming to IS 2645 in recommended proportions including rounding off junction of vertical and horizontal surface. (ii) IInd course of 20 mm cement plaster 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface. (iii) IIIrd course of applying blown or residual bitumen applied hot at 1.7 kg. per sqm of area. (iv) IVth course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 kg/ sqm). (v). 25mm Cpvc spout pipe to be provided at the bottom of the sunken floor of toilet and bath rooms including required drilling etc.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with G.I spl. clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall. 80 mm nominal outer dia Pipes

Providing and fixing PVC floor Trap of Make: "Supreme" Size:- 110mm, Socket Type:- "S", Length:- 278mm, Depth of outlet:- 110mm & Height of Trap-118mm with necessary concrete bedding in floors with necessary cutting, placing, etc., complete all as required and directed by the Engineer-In-Charge.

Polishing on mosaic flooring with mechanical method using approved stain removal powder coating, final coat with smooth finishing of wax polish including skirting and staircase, removing and laying mosaic flooring wherever required with fresh material etc., complete as per direction of engineer in charge. required to give high gloss finish complete. Three coats of machine polish or as required finish as per direction of Engineering-in-charge.

Supplying and fixing Health facet of approved design including with angle cock and required CP fittings as per direction of Enginner-in-Charge.(1.5m length) Make: Jaguar or equivalent.

Providing and Fixing uPVC - SWR (sewage waste & Rain water) pipes for sewer lines - Type :B of ISI: 13592 of approved make and quality with all necessary specials such as collars, elbows, tees, doors Y's, door T`s ,cowl cap, etc., using joining ring with solutions for necessary stage work at duct area , including Providing and fixing G.I. coated Special clamps with bolt nut at 1m c/c or as required all complete at site conditions in all leads and lifts and as directed by the Engineer-in-Charge. 110mm dia.

Providing and Fixing uPVC - SWR (sewage waste & Rain water) pipes for sewer lines - Type :B of ISI: 13592 of approved make and quality with all necessary specials such as collars, elbows, tees, doors Y's, door T`s ,cowl cap, etc., using joining ring with solutions for necessary stage work at duct area , including Providing and fixing G.I. coated Special clamps with bolt nut at 1m c/c or as required all complete at site conditions in all leads and lifts and as directed by the Engineer-in-Charge. 75mm dia.

Providing and Fixing uPVC - SWR (sewage waste & Rain water) pipes for sewer lines - Type :B of ISI: 13592 of approved make and quality with all necessary specials such as collars, elbows, tees, doors Y's, door T`s ,cowl cap, etc., using joining ring with solutions for necessary stage work at duct area , including trenching and filling the earth as required connection to the existing chember etc all complete as directed by the Engineer-in-Charge. 110mm dia.

Dismantling Existing pipes of any diameter inlet and outlet pipes for GI/Pvc/SWR/CI all complete as per direction of site incharge (external work)including removal of clamps , making holes, fittings, removing and refixing of water meters etc.,complete taking out the pipes of any diameter of size, manually/ by mechanical means including stacking of pipes in departmental stores as per direction of Engineer-in-charge [ Note: Removed old pipes will be measured for payment]

Providing and fixing C.P towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms.(square type) Make: Jaguar or equivalent

Providing and fixing 30mm thick panel PVC door shutter with bend Beading consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19 mm x 19 mm for styles and 15x15 mm for top & bottom rails. M.S. frame shall have a coat of steel primers of approved make and manufacture. M.S. frame covered with 5 mm thick heat moulded PVC 'C' channel of size 30 mm thickness, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on both side forming styles and 5 mm thick, 95 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided both side of the panel. 10 mm (5 mm x 2 ) thick, 20 mm wide cross PVC sheet be provided as gap insert for top rail & bottom rail, paneling of 5 mm thick both side PVC sheet to be fitted in the M.S. frame welded/ sealed to the styles & rails with 7 mm (5 mm+2 mm) thick x 15 mm wide PVC sheet beading on inner side, and joined together with solvent cement adhesive. An additional 5 mm thick PVC strip of 20 mm width is to be stuck on the interior side of the 'C' Channel using PVC solvent adhesive etc., and including SS Hinges and other fittings like 100mm Al.T-bolt and handles etc.,complete as per direction of Engineer-in-charge, manufacturer's specification & drawing.Both side deccorative. Make: As Approved by Engineering-in-Charge

Providing and fixing factory made P.V.C. door frame of size 50x47 mm with a wall thickness of 5 mm, sheet properly joined with solvent cement adhesive as per sectional view.A mild steel square tube of size 19mm of 19 gauge is inserted inside to give extra structural strength. The door frame can be made with/without rubber gasket as required.if rubber gasket is not required then one strip of 5mm thickness can be eliminated and final size of choukhat will be 50mm x 42 mm.PVC door frame sections are cut in 45° and joined to each other perfectly 90°.'L' shape brackets made out of M.S.square tube are inserted inside the choukhat corners.These brackets are finally fixed using the steel screws from both the sides and including all necessary Aluminium fittings like tower bolt ,keel, Ms Screw handle etc complete as per manufacturer’s specification and direction of Engineer- in-Charge. Make: As Approved by Engineering-in-Charge

Steel work for pipe clamp stand on the wall including welded in built up sections/ framed work, cutting, hoisting , fixing position in the wall with cement concrete, 1:2:4 (i cement: M-sand:20mm aggregate) making hole on the wall and making good with the required cement plaster , applying a suitable priming coat of approved epoxy primer and two coats of epoxy paint all complete as per the direction of engineering in charge.

Providing and laying sunken floor filling with CLC concrete blocks/ Cinder filling of 1:5:10 (1 cement: 5 M-sand: 10 CLC aggregate 40mm nominal size) including all leads and lifting as required and directed by the Engineer-In-Charge.

Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment. Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor: Anti-Termite Treatment- Post Construction Operation Details (i) Drilling at every one foot interval at wall and floor junction. (ii) Drill depth 4-5 inches on both sides. (iii) chemical used- Imidachloprid 30.5 S.C.[Bayer India or equivalent] (iv) Chemical injection done very half an hour up to saturation point(min 4-5 times). (v) Complete electrical conduits /junction boxes chemical treatment.[oil based] (vi) Plugging of holes after chemical injuction. (vii) On completion of work a warranty for a period 5 years is given for the site. (viii) Dliute and injecting Chemical emulision for POST CONSTRUCTIONAL anti-termite treatment (Including the cost of chemical emulsion) (ix) Treatment of existing mansory using chemical emulsion @ one litre per hole at 300mm interval full depth of the hole with Imidachlopride chemical.The hole filled with white/grey cement as directed by the engineer-in-charge

Removing and refixing of Cpvc pipe with clamps including cutting and refixing with required fittings as per the direction Engineering-in-Charge.For all floor level including required scaffolding et. Upto 100mm dia

Shifting of house holds to allotted quaters including all items like furniture , kichenware, storage units, electrical, electronics goods,(except Ac Unit) required installation and shifting back the same to renovated quarters without any damages and as per occupants positionsetc, complete as per the directions of Engineer-in-charge. Lead with in the staff quaters area upto all floor level. [ Rate including Shifting of all the items available at home including required fixing of frams, nails,hooks as per the requirements of occupants etc, ]

Providing and fixing Acrylic glazing in UPVC door, window, ventilator shutters and partitions etc, of 6mm thick plain Acrylic sheet with required is clear embossed with both side UV stabilizer, having at least 60-80% transparency for fixed windows/ 100% clear vision for other windows, conforming to the relevent IS code including cutting to shape and size as required with EPDM rubber / neoprene gasket etc. complete as per the direction of Engineer-in-charge.

Providing and fixing Euro designer tiles of EUROCON/ HINDUSTAN make of approved pattern and design mixed with pigment to match the shade of the slab for jointing complete with base of 20mm thick cement mortar 1:4 (1 cement: 4 coarse sand).

providing and fixing of brass finished magic eye piece with clear visibility and suitable for 30 to 35mm door shutter including making holes in the shutter and making good as per dirction of enginner-in-charge. (as per sample approved by engineer-in-charge)

Civil Part - Buy Back Items

Buy-back of existing Alwindows/Ms windows of frames, shutters, glazing, fittings all complete including dismantling and making good the brick work etc as per the direction of In-Charge. Any size.

Electrical Part

MODULAR LIGHT/FAN PT: Wiring for light / fan / exhaust fan / call bell point with 1.5sqmm FR PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable size GI. box and earthing the point with 1.5sqmm. FRLS PVC insulated copper conductor single core cable etc., as required. Make: FINOLEX/ANCHORROMA/HAVALLS/Legrand

Twin Control light point: Wiring for Twin control point with 1.5 sqmm FRLS PVC insulated copper conductor single core cable in surface/recessed medium class PVC conduit, 2way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sqmm FRLS PVC insulated copper conductor single core cable etc. as required. Make: FINOLEX/ANCHORROMA/HAVALLS/Legrand

A.C. POINT: Supplying and fixing suitable size G.I box with modular plate and cover in front on surface/recessed including providing and fixing 25A socket outlet and 25A modular SP MCB,"C" curve including connections, testing and commissioning etc.as required. Make: Legrand/L&T/MK

CIRCUIT WIRING : Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required MAKE: HAVALLS/FINOLEX/POLYCAB 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

CIRCUIT WIRING : Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required MAKE: HAVALLS/FINOLEX/POLYCAB 2 X 4 sq. mm + 1 X 4 sq. mm earth wire

ELECTRONIC BELL/BUZZER: Supply and fixing Electronic bell/buzzer suitable for single phase,230V, complete with connection,testing etc. as required. MAKE: ANCHOR/PHILLIPS/HAVALLS

MODULAR BELL SWITCH : Supplying and fixing following modular Bell switch on the existing modular plate & switch box including connections but modular plate etc. as required. MAKE: ANCHOR ROMA/MK/LEGRAND Bell push switch

MODULAR 15A SWITCH : Supplying and fixing following modular switch on the existing modular plate & switch box including connections but modular plate etc. as required. MAKE: ANCHOR ROMA/MK/LEGRAND 15/16 amp switch

MODULAR 15A SOCKET : Supplying and fixing following modular socket on the existing modular plate & switch box including connections but modular plate etc. as required. MAKE: ANCHOR ROMA/MK/LEGRAND 6 pin 5/16 amp socket outlet

MODULAR 5A SWITCH : Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but modular plate etc. as required. MAKE: ANCHOR ROMA/MK/LEGRAND 5/6 amp switch

MODULAR 5A SOCKET : Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but modular plate etc. as required. MAKE: ANCHOR ROMA/MK/LEGRAND 5/6 amp socket

MODULAR TV ANTENNA SOCKET: Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but modular plate etc. as required. MAKE: ANCHOR ROMA/MK/LEGRAND TV antenna socket outlet

ELECTRONIC FAN REGULATOR: Supply and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections etc. as required. MAKE: ANCHOR ROMA/MK/LEGRAND

GI Box alongwith modular base & cover plate : Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches & sockets and junction box in recess etc as required. MAKE: ANCHOR ROMA/MK/LEGRAND 2 Module (75 mm X 75 mm)

GI Box alongwith modular base & cover plate : Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches & sockets and junction box in recess etc as required. MAKE: ANCHOR ROMA/MK/LEGRAND 3 Module (100 mmX75 mm)

GI Box alongwith modular base & cover plate : Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches & sockets and junction box in recess etc as required. MAKE: ANCHOR ROMA/MK/LEGRAND 6 Module (200mm x 75mm )

GI Box alongwith modular base & cover plate : Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches & sockets and junction box in recess etc as required. MAKE: ANCHOR ROMA/MK/LEGRAND/GM 12 Module (200mm x 75mm )

PVC Pipe 32mm: Supplying and fixing of medium class PVC conduit along with accessories in surface / recess including cutting the wall and making good the same in case of recessed conduit as required. 32mm Make: Vasavi/Avonplast/Finolex

LABOUR CHARGES FOR Fixing of Exhaust Fan: Installation of Exhaust fan in the exsting opening, including making good the damage, connection, testing, commissioning with 1.5 sqmm FRLS PVC insulated, copper conductor, single core cable etc. as required

Labour Charges for Fixing of louver/shutter for Existing exhaust fan: Extra for fixing the louvers/shutters complete with frame for a exhaust fan of all sizes

PVC BATTEN/ANGLE HOLDER: Supplying and fixing PVC batten/angle holder including connection etc.as required. MAKE: ANCHOR ROMA/MK/LEGRAND

LABOUR CHARGES FOR FIXING OF FLUORESCENT/MIRROR LIGHT FITTING: Installation, testing and commissioning of pre-wired, fluorescent/Mirror light fitting of all types, complete with all accessories and tube etc. directly on ceiling/ wall, including connections with 1.5sqmm FRLS PVC insulated, copper coductor, single core cable and earthing etc. as required.

LABOUR CHARGES FOR FIXING OF CEILING FAN: Installation, testing and commissioning of ceiling fan, including wiring in the suitable size of down rods with 1.5 sqmm FRLS PVC insulated, copper conductor, single core cable, including providing and fixing phenolic laminated/PVC sheet cover on the fan box etc. as required.

REMOVAL OF ELECTRICAL ITEMS: Removing the existing connection,wires, unused metal enclosures, switch boards, fixtures,ceiling fans,exhaust fans,DB's.etc., and same have to be haneded over to department as directed by dept, Engineer.

EXHAUST FAN: Supply of 225mm Sweep Exhaust fan with metal type model for kitchen/bathroom complete with all accessories.. etc, as required . Make: Havells / USHA/ Almanord/Crompton

20W 4Ft Light fitting : Supply of 4ft 20W 6500K 2000lumen LED/Conventional type Light fitting with fixing accessories on surface /wall etc. as required. Make: Crompton/ Philips/Havells/Wipro

18W LED Surface Fitting: Supply & fixing of 18W LED 6500K (595mmX595mm) Surface fitting round/square light suitable fitting including Installation, testing and commissioning of pre-wired, fluorescent/Mirror light fitting of all types, complete with all accessories and tube etc. directly on ceiling/ wall, including connections with 1.5sqmm FRLS PVC insulated, copper coductor, single core cable and earthing etc. as required. Make: Crompton/ Philips/Havells

MIRROR LIGHT FITTING : Supply of 9W LED mirror light suitable fitting (Crompton/ Philips) to complete with all assocessories etc., as required. Make: Crompton/ Philips/Havells/Wipro

Making hole50mm in Wall : Making hole through wall & providing PVC pipe (50mm) for installation of AC outdoor unit pipe & cable by demolishing brick work manually and the same as good finishing of wall by plastering etc as required.

Shifting of AC Unit: Removing,Shifting & Refixing of existing Split AC Unit(upto 2Ton) with suitable copper pipe, wiring including 5.0 Rmt copper tubing,drain pipes, and electrical wiring connection,M.S stand for keeping outdoor unit of Split A/C.with M.S cage for locking of outdoor unitof Split A/C. including painting etc. complete as directed by Engineer

SINGLE ARM WITH LED FIXTURE: Supply,Installation,testing and commisioning of prewired,LED post angled type fitting with 40W LED lamp.The job including supplying and fixing of suitable size bracket with bolt,nut,washer with single armed G.I pipe,making the connection with 2.5sqmm FRLS PVC insulated copper conductor,single core cable to junction box.etc,as required. Make: Crompton/Philips/ Havalls.

CEILING FAN: Supply of ceiling fan with minimum 3 star rating, colour of gray/brown/ivory, 1200 mm sweep, double ball bearing (without regulator) etc., as required as directed by department. Make: Crompton /Orient/Almonard/Havells/Usha

JPS Constructions

prabu company

JPS Constructions

prabu company