Development of Yelagiri Boat House in Tirupathur district

Amount

Earth work excavation for foundation (for narrow excavation) in all soils and sub-soils such as ordinary soil and hard gravelly soil to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by the departmental officers with an initial lead of 10 mts and initial lift of 2 mts. and clearing and levelling the site, etc., complete complying with standard specification.

Supplying and filling M-Sand in foundation, basement, layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers.

Supplying and FILLING GRAVEL in 'foundation and basement with filling crushed stone sand in layers of not more than 15cm.thick well rammed watered and compacted -1m3 etc., complete complying with standard specification.

Cement Concrete 1:5:10 (One Cement, Five crushed stone sand and Ten hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for foundation including dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification

Plain Cement Concrete 1:2:4 (one cement, two crushed stone sand and four hard broken stone jelly) using 20mm jelly for wearing coat including laying, compacting, finishing and curing, etc., complete as per standard specificatins and as directed by the departmental officers.

Supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 M height for plane surfaces as detailed below in all floors with all cross bracings using Mild Steel sheets of size 90 x 60 cm and 10 BG stiffened with welded Mild Steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton. (Payment for centering shall be given after the concrete is laid)

For plane surfaces such as RCC floor slab, roof slab, beams, lintels, bed blocks, landing slab, waist slab, portico slabs and beams .

For plane surfaces such as rectangular or square RCC columns, sunshades, top and bottom slab of RCC boxing, etc.

For plane surfaces such as vertical slab, side slabs of boxing, vertical drops, facia, vertical wall, etc.

Providing and laying in position, Standardised Concrete Mix M-30Grade in accordance with IS:456-2000 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cementcontent of 400 kg/m3 and maximum water cement ratio of 0.45, including admixture (plasticiser / superplasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5.0 cu.m.) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 cu.m.) 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu.m') 7670 kg. of crushed stone sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers.The coarse and fine aggregates to be used should comply with therequirements of IS Standards. (No separate payment will be made by the Department for the excess usage of materials).

For Foundation and Basement

For Ground floor

Supplying, fabricating and placing in position TMT rod grills for all RCC works as per design given including cost of steel and G.I. binding wire in all floors etc. complete complying with standard specification. (Contractor has to make his own arrangements for the supply of steel and binding wire)

Brick work in following Cement Mortar 1: 5 (one cement and five sand) using best quality II class Ground moulded chamber burnt bricks of size 9" x 4-1/2" x 3" for foundation and basement including curing, etc., complete complying with standard specifiction. a)For Foundation and Basement

Supplying and fixing of the size of 50mm x50mm x6mm ,40mm x40mm M.S L - Angle and flat of 32mm x6mm for the bottom frame of floating boat jetty, the rates inclusive cost and welding charges etc complete.

Fixing the 20 Nos new barrel and 2'9" x 2'0" in the floating boat jetty. The barrel should be fixed as per instructed by departmental officers

Supplying and Providing 3mm thick Aluminum chequered sheet over the M.S frames. The rates inclusive of providing end Aluminum beeding of 32mm x20mm all round and providing beeding in between sheet and including screws etc complete.

Supplying and fixing the old tyers around the new floating boat jetty with bolt nuts as per instructed by departmental officers

Painting new iron frame works ., with two coats of best approved first quality and colour of aspa paint over one coat of red oxide priming coat in all floors including cost of priming coat etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

Plastering in cement mortar 1:5 (One cement, and five sand) 12mm thick including curing and finishing neatly complying with standard specification and as directed by the Corporation Officers etc.

Plastering and finishing the exposed surface of all RCC items of work such as slabs, beams, sunshades, facia, canopy slab, staircase waist slab, landing slab etc., with Cement Mortar 1:3 (One Cement and Three Plastering Sand) 10mm thick including hacking the surfaces, providing cement mortar nosing, beading for sunshades, staircases, steps, landing slabs and curing, etc., in all floors complying with standard specification and as directed by the departmental officers

Painting the newly plastered wall surfaces two coats with approved weather proof Exterior Emulsion paint over etc., complete complying with standard specification.

Painting the wall two coats with approved weather proof Exterior Emulsion paint over one primer coat of over cement plastered wall surface ect., complete complying with standard specification.

Fabricating supplying and fixing in position of Steel container for Ticket counter and Store room Shipping Containers Size : 6M x 2.40M x 2.60M with partition 10x8 ft for ticket counter and 10x 8 ft for storage place. Main Entrance Door size : 6.5 ft x 3.5 ft 1 No and MS counter with tray and hinges .LED square light - 2 nos ,5A socket- 2 nos,Tube light -1 no,Bulk head- 1 no ,Wall fan -1 no, MCB- 1no . Internal Panelling : 340sft insulation of thermocol and 8mm MDF sheet 1.3mm vinyl matt for floor Painting: Two coat of Asian enamel paint finish (as per required colour). and two no Rack of size 10feet x 2feet complete complying with standard specification and as directed by the departmental officers.

Fabricating supplying and fixing in position of Steel container for Caféteria Food Kiosk Shipping Containers Size : 6M x 2.40M x 2.60M Main Entrance Door size : 6.5 ft x 3.5 ft 1 No and MS counter with tray and hinges -1 no , 20x2 ft running table with 18mm plywood &mic aby using MS frame sttucture .LED square light - 3 nos ,5A socket- 3 nos,Tube light -1 no,Bulk head- 1 no ,Wall fan -2 no, MCB- 1no . Internal Panelling : 608sft insulation of thermocol and 8mm calcium silicate baord with one coat wall putty and two coats of primer and Painting ,2'x2' Virtified tiles for floor Painting: Two coat of Asian enamel paint finish (as per required colour). complete complying with standard specification and as directed by the departmental officers.

Fabricating supplying and fixing in position of Steel container for Toilet- 4 nos Shipping Containers Size : 6M x 2.40M x 2.60M with partition 8 ft x 4 ft - 4 nos Main Entrance Door size : 6.5 ft x 3.5 ft 4 nos metal safety door with lock and sunshade .Bulk head- 4 no ,Toilet light - 4 no. Internal Panelling : 608sft insulation of thermocol and 8mm calcium silicate baord with one coat wall putty and two coats of primer and Painting ,2'x2' Virtified tiles for floor and 4 feet height wall tiles for every toilet. Painting: Two coat of Asian enamel paint finish (as per required colour).Plumbing fittings of EWC - 4 nos ,Wash basin - 4 nos,Tap - 4 nos complete complying with standard specification and as directed by the departmental officers.

Supplying, laying and jointing UPVC pipes (having working pressure 10 kg. / sq.cm) of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing UPVC specials using UPVC adhesives (but excluding cost of such specials) and fixing into wall with teak wood plugs, PVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges upto 4 metre height above ground level, etc., complete complying with standard specifications. The PVC pipes shall be got approved by Executive Engineer before use on works.

20mm dia

25mm dia

50mm dia

Supplying UPVC Specials (with working pressure 10 kg. / sq.cm.) in water supply arrangements (both in internal and external water supply arrangements

50 mm Dia Elbow

25mm dia Elbow

20mm dia Elbow

50 mm Dia TEE

25mm dia TEE

20mm di TEE

50 mm Dia BEND

25mm dia BEND

20mm dia BEND

50 mm Dia COUPLER

25mm dia COUPLER

20mm dia COUPLER

Supplying and fixing in position best quality PVC soil / waste pipes of various dia having 6 kg / sq.cm. pressure BIS mark and providing leak proofjoints using PVC adhesives including fixing to the wall with special clamp, teak wood plugs, brass screws, etc., and making connection to all sanitary fittings, dismantling masonry / RCC works wherever found necessary and making the good dismantled portion to the original condition, including testing for any leakages, etc., complete complying with standard specifications. (The PVC pipes should be got approved by the Executive Engineer before use on works). The rate for earth work excavation will be measured and paid separately in the cases where the pipe lines are proposed to laid below ground level

75mm dia

110mm dia

Supplying and fixing in position PVC specials of the following dia and types of approved quality confirming to BIS and providing leak proof joints including fixing to the walls and giving connection to the PVC soil stacks, dismantling the masonry or RCC works and re-doing the dismantled portion to original condition etc., complete complying with standard specifications. (The PVC specials should be got approved by the Executive Engineer before use on works).

75mm dia Elbow

110mm dia Elbow

75mm dia Elbow with Door

110mm dia Elbow with Door

75mm dia Tee

110mm dia Tee

75mm dia Tee with Single Door

110mm dia Tee with Single Door

Construction of INSPECTION CHAMBER following clear sizes including earth work excavation, CC 1:5:10 of 10 cm thick and brick work in Cement Mortar 1:5 [One cement and Five sand] using best quality of second class Table Mould Bricks of size 9" x 43/8" x 23/4" with Plastering with Cement Mortar 1:3 [One Cement and Three Plastering Sand] 12 mm thick to inner and outer sides and wearing coat 1:3:6 [One Cement, Three crushed stone sand and Six Aggregate] 15 cm thick and covered with precast slab 5 cm thick etc., complete complying as directed by the departmental officers as per standard specification.

Supplying anf fixing Heavy duty man hole cover 600mmx600mm Heavy duty man hole cover with frame.

Supplying and fixing in position first quality and approved variety of Gun metal Gate Valve with BIS make of the following dia including cost of shellac, thread balls, etc., complete complying with standard specifications (for both internal and external water supply arrangements). The valves to be used on work shall be got approved by the Executive Engineer before use on work.

50mm dia

25mm dia

20mm dia

Manufacturing, Supplying and Fixing of Stainless Steel Entrance Gate for the size of 6.00mx1.65 m using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick at required locations to a height of 1.60m from finished Pathway welded to 38mm dia Stainless Steel pipe post of 1.00mm thick as vertical at 230mm centre with 42 Nos. of 25mm dia intermediate Verical horizontal stainless steel pipe of 1.60mm thick in between as per given design. The vertical pipe has to be welded to the 100 X 100 X 6mm MS base plate encased in the base concrete. The rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance, electrical charges, etc. complete as per standard specification.

Supply & erection of M.s Angle pole of size 50mmx50mmx6mm and required length including provision of anchorage clamp and making holes for fixing chain link fencing , erection in true alignment with necessary foundation concrete including cost and conveyance of all materials , labour but excluding the cost of concrete etc...complete complying with standard specification.

Providing PVC Coated Chain Line Fencing of size 50mmx50mm 10guage to a height of 1.50m fixing with M.S angle poles using M.S flats of size 25mmx5mm fixing horizontally in between the angle poles. The rate is including providing holes in the M.S flats fixing M.S bolt and nuts with the angles, with the flats, cost of tiening wires etc /boltes&nuts etc complying with standard specification.

Trenching in ordinary soil up to a depth of 60 cm including removal and stacking of serviceable materials and then disposing of surplus soil, by spreading and neatly levelling within a lead of 50 m and making up the trenched area to proper levels by filling with earth or earth mixed with sludge or / and manure before and after flooding trench with water (excluding cost of imported earth, sludge or manure) etc. Complete Complying Standard Specification.

Supplying and stacking of good earth at site including royalty and carriage upto 5 km lead complet etc. Complying Standard Specification. (earth measured in stacks will be reduced by 20% for payment).

Supplying and stacking at site dump manure from approved source, including carriage upto 5 km lead complete (manure measured in stacks will be reduced by 8% for payment)

Providing and laying Bermuda grass turf with earth 50mm to 60mm thickness of existing ground prepared with proper level and ramming with tools wooden (Dhurmos) and than rolling the surface with light roller make the surface smoothen and light waterning with sprinkler and maintenance for 30 days or more till the grass establish properly etc. Complete Complying Standard Specification.

Providing and stacking of Ten Varieties Creeper flower plants well developed with fresh and healthy etc. Complete Complying Standard Specification.

Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any, with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately) etc. Complete Complying Standard Specification.

Providing and stacking of Half Shaded Plants twenty varieties such as Spider lilly, Bird of Paradise, Eternal flame, Flamigo flower, Flaming sword, Peace lilly, Poinsettia, Areca palm, Arrow Head, cast iron plant, Chinese evergreen, Corn Plant, Diffenbachia, Cordyline fruticosa ,Heart leaf, Rubber plant, Scheffra, Zebra Plant , Zo-Zo Plant & Snake Plant well developed with fresh and healthy 60 cm ht., etc. Complete Complying Standard Specification.

Providing and stacking of Budha Bamboo well developed with fresh and healthy 3 to 4 ft etc. Complete Complying Standard Specification.

Providing and stacking of Water Bamboo well developed with fresh and healthy 3 to 4 ft., etc. Complete Complying Standard Specification.

Providing and stacking of Border Plants (Golden Duranta, Iskinthari & Alamanda) well developed with fresh and healthy 4 to 5ft etc. Complete Complying Standard Specification.

Supplying and fixing of PVC Pipe springler and trip irrigation water line including all following components as directed by the departmental Officers (Includes transportation and labour charges) (as per Quotation) etc.complete complying with standard specification

50mm (2" ) Pipe

40mm (1.5" ) Pipe

50mm Bend (2" )

50mm Tee(2" )

50mm end cap(2" )

2'' Ball value

2" Filter

2 H.P.Motor (3 phase)

Popup adjustment sprinkler (360 degreeX360 degree)

Trip Irrigation pipe roll

Supplying of Park Bench Stainless Steel (VSP-67) having Square Tubes of 50mmx25mm, 50mmx50mm for a length of 5 ft and height of 2-1/2 feet etc complete with standard specification.

Supplying and fixing in position of the Granite Stone Benches of Size 1.50 M length x 0.60m ,width x 0.10m thick and legs of 0.90m height x 0.60m width x 0.10mm thick.The rate is inclusive of cost of all materials and labour charges etc complete with necessary earth work excavation,mat concrete with CC 1:5:10 and foundation concrete with PCC 1:2:4. as directed.

Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A one way module switch with module front plate continuous earth wire connection of 1.5 sq.mm copper wire and making good of the concealed portion with suitable colour for Concealed PVC Light point / fan point.

Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe on wall and ceiling and switch drop portion PVC rigid pipe concealed in wall with PVC accessories with Module GI switch box in flush with wall with 6A one way module switch with module front plate with continuous earth wire connection of 1.5 sq.mm copper wire with painting of Suitable colour for Open PVC Light point / fan point.

Wiring with 3 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A two way module switch with module front plate with continuous earth wire connection of 1.5 sq.mm copper wire and making good of the concealed portion with suitable colour for Concealed PVC pipe Stair case Light point.

Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories with suitable Module GI switch box in flush with wall with 1 no. 6A one way module switch and 1 no. 6A 3/ 2 pin module socket with module front plate with continuous earth wire connection of 1.5 sq.mm copper wire and making good of the concealed portion with painting of suitable colour for concealed PVC pipe Plug point.

Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC Rigid pipe on wall and ceiling and switch drop portion PVC rigid pipe concealed in wall with PVC accessories with suitable Module GI switch box in flush with wall with 1 no. 6A one way module switch and 1 no. 6A 3/ 2 pin module socket with module front plate with painting of Suitable colour with continuous earth wire connection of 1.5 sq.mm copper wire for Open PVC conduit Plug point.

Wiring with 2 x 4 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitablePVC rigid pipe Concealed in wall and ceiling with PVC accessories with suitable Module GI switch box in flush with wall with 1 no. 1OA one way module switch and 1 no. 16A 3/ 2 pin module socket with module front plate with continuous earth wire connection of 4 sq.mm copper wire and making good of the concealed portion with painting of suitable colour for Concealed PVC pipe power Plug point.

Supply and Run of 2 of 2.5 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with continuous earth wire connection of 2.5 sq.mm copper wire and making good of the concealed portion.

Supply and fixing of 8 way Vertical Triple pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 63 A 4 P MCB switch as incoming and 24 nos. 6A to 32A SP MCB as outgoing on wall with earth connection only.

Supply and fixing of LED type 4' 18 W fitting complete on wall or ceiling with PVC unsheathed FRLS Copper leads from terminals to the fitting etc., complete.

Supply and fixing of LED type 2'9 W fitting complete on wall or ceiling with PVC unsheathed FRLS Copper leads from terminals to the fitting etc., complete.

Supply and fixing of 18W LED square type Recessed fitting with LED on false Ceiling/ Surface with suitable hanging support from ceiling with PVC unsheathed copper leads from terminals to the fitting.

Supply and fixing of 30W LED street light fitting with LED (Lower end) with 25mm dia. GI pipe (class B) with 1 no.25mm GI bend complete on the existing post/ on wall with PVC unsheathed copper leads with MS clamps and with painting etc., Complete.

Supply and fixing of l200mm (48") sweep AC ceiling fan 5 star rated complete with 2 module 100W fan step regulator (Lower end) with 1 metre down rod with fan clamp with side plates and cross arm of size 450mm (18") etc., complete.

Supply and fixing of 375mm (15") sweep (light duty) AC exhaust fan complete without provision of holes in the wall etc., complete.

Supply and laying of 3 1/2' x 50 sq.mm PVC armoured LTUG cable in a trench to be excavated at a depth of 0.75 metre putting 0.15 metre layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good etc., complete.

Supply and laying of 3 1/2' x 35 sq.mm PVC armoured LTUG cable in a trench to be excavated at a depth of 0.75 metre putting 0.15 metre layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good etc., complete.

Supply and frxing of brass cable gland for following PVC armoured LTUG cable with earth connectionetc., complete.

3'Zc x 50 sq.mm

3'Zc x 35 sq.mm

Supply and providing cable end termination for the following PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete.

3'Zc x 50 sq.mm

3'Zc x 35 sq.mm

Earthing as per the ISI specification with an earth electrode of 2.10 metre C1ass'B' GI pipe of dia not less than 40mm with copper earth plate of size l25mm x 50mm x 6mm with necessary funneling arrangements with necessarymasonry work and with 38mm RCC cover slab for the brick masonry. etc., complete.

Supply and run of 1 of No.8 SWG GI wire for earth connection etc. Complete.

Supply and fixng of TNEB meter board suitable for 3phase 100A service connection made up of suitable angle iron frame work of size 2feetx1- 1/ 2feet using angle iron of size1-1/2"x1 1/ 2"x1/4" rigidly fixed on wall covered with hylem sheet of size 2feetx1-1/ 2feet of 12mm thickness with necessary bolts and nuts supports and supply and fixing of 3Nos. 100A fuse units (500V), 1No.neutral1ink, copper earth flat of size1"x1/4" with interconnection of EB meter to fuse units by 16 Sq.mm PVC insulated copper wire with earth connection complete.

SUPPLY OF TUBULAR 8M HEIGHT SINGLE ARM CONICAL POLE (HEKA BRACKET) 8M Height Single Arm Pole is made in combination of Conical section made of High tensile MS Sheet(3mm thick minimum) with top dia. 75mm & bottom dia. l57mm dia. and Heka design bracket which is made in combination of Steel pipe sections O0mm dia.(vertica1),60mm dia.(horizontal) &gradually bent 42mm dia.,to provide pleasing aesthetics & an arm length of l000mm & pleasing aesthetics. Entire pole & Bracket shall be made to provide pleasing aesthetics as approved by Concerned Engineer in-charge. After Fabrication, Entire Pole is effectively treated with chemical composition in order to have the durable corrosion resistance. The pole should be provided with an inbuilt junction box with lNo. 32A Heavy Duty Stud type connector and lNo. 6A SP MCB, at the bottom - the inbuilt box should have a flush door of suitable size. The pole to be provided with suitable size base plate. This base plate along with foundation bolts of suitable size to be used for ensuring firm grouting into the specially designed RCC foundation. wind pressure calculation as per IS 875(part-3) & structural calculation report as per EN40 should be submitted to verify the pole design. Pole & it's parts are painted in 3 layer coating(coating thickness 100 microns minimum) inpwhich 1st layer withpetch primer,

SUPPLY OF LIGHT 104, LED, 48W, 4000K,IP 66 Light 104 Upper frame made in aluminium, with quick coupling threaded G 3/4" for fixing to support. Bottom frame also in aluminium, removable for access to the wiring and optical compartment. Fixing with 3 screws in stainless steel. Gasket in silicon between the upper and bottom frames. Pure polyester powder coating in Standard NERI Grey Colour.IP Rating - IP 66. Height — 225mm,Diameter - 420mm,Weight - 6.5Kg, Area Exposed to Wind(S) - 0.05 m2 Power LED Module with Company /brand name printed on PCB with the metal core plate .LED Chips of CREE/ NICHIA/ OSRAM/ LUMILEDS make - same should be supported by LED manufacturer's tech sheet . Colour Rendering Index: Ra > 70. Electronic Power Supply for LED Module, which offers Protection against Short Circuit, OverVoltage & Over- Current, with in- built surge protection of 4kV minimum (an additional surge protection device of 10kV also provided in-built the fixture). Optics with refractive lens in PMMA/ PC . LED Lifetime >1,00,000houre@Ts 85°C. LM80 report from LED Manufacturer should be submitted. Safety test report as per IEC 00598 from UL/UL authorised/Intertek Lab should be submitted. LM79 report also should be submitted from UL/UL Authorised/Intertek Laboratory. BIS certificate with brand same as manufacturer also should be submitted.

Supply fabricaton and install on of 200 Amps LV panel made out of 14/ 16 SWG CRCA sheet steel enclosure, welded construction floor mounting type with grey powder coated suitable floor mounting in angle iron frame with comprising of following arrangements etc., complete. Incomer: 200 Amps TPN switch - 1 No Outgoing: 32 Amps TPN Switch - 1 No 63 Amps TPN Switch - 5 Nos Bus Bar: 500mm x l00mm x 6mm - 3 Nos

Providing chemical earthing as per the ISI specification with an earth electrode of 3.0mt class 'B' GI pipe with necessary funneling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry.

GST at 18%

R SUDHAKAR (BID ID -1415926)