ADDITION ALTERNATION OF ELECTRIC WIRING IN BLDG NO DT-9 AT OFFR MESS FCSR INCLUDING CERTAIN E M SANCTIONED WORKS AT SHILLONG UNDER GE SHILLONG

Amount

Material and labour for Point wiring with 1.50 Sqmm single core PVC insulated , unsheathed cable FRLSH, 1100 volt grade with multi stranded copper conductor drawn through and incuding medium grade, ISI marked, PVC conduit not less than 20 mm dia with accessories,cassing capping on wall/ceiling and incuding provision of 1.50 Sqmm single core PVC insulated , unsheathed cable FRLSH, 1100 volt grade with multi stranded copper conductor green colour as earth continuity conductor and connected to common earth dolly with suitable size of lugs, including mild steel sunken box/metal flush box with suitable modular or pressed steel terminal boxes made out of 1.6 mm thick mild steel sheet metal conforming to IS-5139(pt-I) of 1969 and IS:14772-2000 with earth dolly and coated with two coats of anti corrosive paint over a coat of red oxide primer both internally and externally including provision of new 3 mm thick plastic laminated sheet top cover for housing the switches , socket outlets, fan regulators etc. with brass screws and brass washers and making good the disturbed surfaces as per existing for one light point controlled by one switch including taking down old unserviceable one etc complete all as specified and as directed. Note :- Switch, socket and fan regulators to be measured and paid for separately . PVC Conduit confirming to IS 9537 part I & III .Note (All chases will be cut by chase cutter only) .Make of cable:- KEI / RR Kabel / Havells . PVC Casing & Capping:- Prestoplast / Finolex / Kalinga

All as per item No 1.00 above but for one 2/3 pin socket outlet 5/6 Amps point on same board etc complete all as directed by Engineer -in -Charge .Make of cable :- KEI / Finolex / Havells and Make of PVC casing & capping :- Prestoplast / Kalinga / Finolex.

All as per item No 1.00 above but for one 2/3 pin socket outlet 5/6 Amps point on independent board etc complete all as directed by Engineer -in -Charge .

All as per item No 1.00 above but for one bell point controlled by one bell push etc complete all as directed by Engineer -in -Charge .Make of cable :- KEI / Finolex / Havells and Make of PVC casing & capping :- Prestoplast / Kalinga / Finolex.

All as per Item No. 1.00 here-in-before but with FRLSH grade, (ISI mark) PVC insulated and unsheathed two run multistranded copper conductor of size 4.0 Sqmm for one power point of 3 pin 15 Amps on independent board including FRLSH grade (ISI mark), PVC insulated, unsheathed one run multi-stranded copper conductor of size 4.0 sqmm green in colour as earth continuity conductor connected to common earth dolly complete all as specified and directed.Make of cable :- KEI / Finolex / Havells and Make of PVC casing & capping :- Prestoplast / Kalinga / Finolex.

Supply and fix, Switch piano (ISI marked) Single pole 240 volts, one way 5/6 Amps complete all as specified and directed.

Supply and fix Switch socket combination (ISI marked), 2/3 pin and 5/6 Amps, 240 volts complete all as specified and as directed.

Supply and fix Switch socket combination (ISI marked), 2/3 pin and 15/16 Amps, 240 volts complete all as specified and as directed.

S&F Ceiling rose, 3 terminals PVC/polycarbonate, isolated body complete all as specified and directed.

S&F bell push ( ISI marked), single pole 240 volts, 5 Amps etc complete all as specified and directed.

Supply and fixing call bell ding dong, AC, 230 V, Single pole ISI marked etc complete all as specified and as directed.

S&F in repair decorative wall mounted LED batten fittings with all accessories, 1X18 Watt, extruded aluminium heat shrink type and provided for efficient heat dissipation and integrated electronic driver and fixed to wall with 2 Nos PVC block of suitable size complete all as specified and as directed. Make Havells Cat part No. LHEXBQP71N1W018 / CROMPTON Cat Part No. LCTL 18 CDL. / Philips cat part no. DX UJJWAL.

S & F in repair recess mounted low glare luminaire 28 Watt PLUTO NEO 2 X 2 complete with all accessories etc complete all as specified and as directed. Make Havells Cat Part PLUTONEO 2X2PLR28WLED857S or equivalent model in Bajaj / CG.

S&F in repair Decorative wall mounted LED batten fittings with all accessories, 1X 9 Watt, extruded aluminium heat shrink type and provided for efficient heat dissipation and integrated electronic driver and fixed to wall with 2 Nos PVC block of suitable size complete all as specified and as directed Make :- Crompton Cat part No. LCTL-9-CDL or Make:- Havells Cat part No. LHEXBQP7IN1W009.

Supply and fixing LED Building security light 25 watt ,pressure die cast aluminium housing heat resistant glass, IP 65 protection, better optics for uniform distribution complete with all accessories internally pre wired and including connecting up with three core 1.5 sqmm flexible copper conductor cable from ceiling rose to connector of light including suitable size bracket and necessary electric connection etc complete all as specified and as directed.Make:- Bajaj cat part no. 169821 LED or CG cat part no LSTO 25 CDL equivalent make of Philips / Havells.

Supply and fix in repair MCB Distribution board , 240 volts single pole and neutral ,double door, sheet steel, enclosure powder coated with 100 Amps rated busbar with neutral link, 8 ways , fixed on wall duly grouted in solid block wall or on wooden board with electrical connection complete all as specified and directed. Make: Havells Cat part No DHDPSHODRW08 or equivalent in Schnieder/GE/C&S.

Supply and fix in repairs MCB DB 4 way vertical sheet metal enclosure TPN 415 volts, 50 Hz, with IP-43 protection, double door with 200 Amps standard bus bar of suitable size and common neutral link all enclosed in standard sheet flush mounting with one MCCB 100 Amps 4 Pole 25 KA as incommer complete all as specified and as directed. (Make:- Havells cat No :DHDLVDRRNAOF004 or equivalent make as Seimens /Legrand . (Note : MCB SP/TPN shall be measured and paid seperately under appropriate items of this schedule . Note : Copper thimble shall be used for connection of cable.

Supply and fix MCCB ,four pole , 415 Volt, 100-125 Amps,16 KA , adjustable thermal & fixed magnetic setting complete all as specified and directed.Make: Havells Cat part No -IHDA3BBF0100 or equivalent in Schnieder/GE/C&S / Havells.

Supply and fix in repair isolator/ MCB DP, 240 Volts, 40 Amps, 10 kA rupturing capacity 'C' series complete all as specified and as directed. Make: Havells Cat part No - DHMCCDPF0040 or equivalent in Schnieder/GE/C&S.

Supply and fix in repairs Isolator MCB, single pole 240 V, 6 to 32 Amps etc complete all as specified and as directed.Make : Havells / Schneider / Indoasian / Legrand.

Material and labour for sub main wiring with two single core 6.0 sqmm FRLSH, ISI marked PVC insulated multi stranded, unsheathed copper conductor cable and one single core unsheathed FRLSH , ISI marked, PVC insulated multistranded copper conductor cable of size 6.0 sqmm green colour as earth lead including PVC casing capping of suitable size including taking down old unserviceable one complete all as specified and directed, .(Note: two run of 6.0 sqmm cable , one run of earth wire of 6.0 sqmm and one run of PVC casing capping shall be measured as one length).Make- Cable- Finolex/RR cable/KEI, PVC Casing Capping- Presto plast/Finolex/Kalinga.

Supply, fixing and testing , electrically driven water heater (Geyser) , storage type, BEE 5 star rating , 25 litre capacity , grouting in brick wall with new GI nut & bolts of suitable size including provn of 2 Nos PVC connection 450 mm long suitable for geyser and necessary incoming and outgoing electric and water connections with hot / cold PVC pipes including testing etc complete all as specified and directed. Make: Havells product code GHWCANTWH025 or equivalent to Bajaj / Venus / Racold

S&F GI water tubing 15 mm dia medium grade with all necessary GI fittings such as bends, elbow, tees, sockets etc ,laid in trenches or fixed in wall, ceiling or floor with necessary GI clamp or hook etc complete all as specified and as directed.

S&F Bib taps, chromium plated cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule etc complete all as specified and as directed.Make:- Prayag / Sona / Parryware.

S&F 15 mm bore angle stop valve cast copper alloy, chromium plated screwed down high pressure with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe etc complete all as specified and as directed.Make:- Prayag / Sona / Parryware.

Material and labour for earthing complete with galvanised steel earth plate electrode 60 Cm X 60 Cm X 6 mm buried directly in ground vertically to a depth notless than 2.25 mtr deep below ground level with top edge of earth plate at a depth not less than 1.5 m below normal ground level connected to galvanised earth lead wire 4.0 mm dia by means of bolts, check nuts and washers ,galvanised steel and protected by GI pipe 15 mm bore light grade & connected to main switch board or main control board as directed and including concrete pit in PCC (1:3:6) type C1, precast RCC (1:2:4) type B1 cover slab 30 cm X 30 cmX 5 cm with 10mm dia TMT bars 8 cm C/c both ways and one handle for lifting made out of 8 mm dia TMT bar, funnel, wire mesh, 20mm bore galvanised iron pipe (medium grade) for watering, charcoal or coke and salt in alternative layers, necessary excavation and earth work in any type of soil and including necessary testing complete all as shown in Electrical Plate No 3 of SSR part -I etc including taking down old unserviceable one etc complete all as specified and as directed.

Excavation in trenches n exc 1.5 mtr wide and depth n exc 1.5 mtr deep for foundation, etc n exc 10 sqmtr on plan, in soft/loose soil and getting out complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers n.exc 25 Cm thick as in soft/loose soil etc complete all as specified and as directed.

Removing excavated materials (soil) n.exc 50 m and depositing where directed at a level n.exc 1.5 m above the starting point complete all as directed.

M&L for Sand cushioning with dry clean river sand for protection/covering of under ground cable in trenches complete all as specified and directed by Engr-in-Charge. Note:- Punned thickness only shall be measured for payment.

Supply and laying Sub class 'B' well burnt brick, laid flat in trenches as protection to LT XLPE cable complete all as specified and as directed.

Supply, laying XLPE insulated PVC inner sheathed, armoured with galvanized steel strip or wire heavy duty underground cable with stranded aluminum conductor 1100 volt grade of size 25 Sqmm 4.0 Core, confirming to IS, laid in trenches / duct passing through pipe / duct or fixed on pole and connecting and testing including taking down old unserviceable one complete all as specified and directed.

Supply, laying XLPE insulated PVC inner sheathed, armoured with galvanized steel strip or wire heavy duty underground cable with stranded aluminum conductor 1100 volt grade of size 25 Sqmm 4.0 Core, confirming ti IS, laid in trenches / duct passing through pipe / duct or fixed on pole and connecting and testing complete all as specified and directed.

Supply and laying GI tubing light grade,40 mm bore with all GI fittings, fixed complete to walls and ceiling or laid in floor for cable crossing complete all as specified and as directed

Supply and erecting steel tubular swaged pole 11 mtr long type 410 SP-55 complete with cast iron base plate and final taper plug duly painted with anti corrosive paint internally and externally and upto 1.5 m length of pole above ground level (externally) shall be painted with two coats of synthetic enamel paint in strips of 30 Cm length, black and yellow alternatively and balance of pole with two coats of aluminium paint etc complete all as specified and as directed by Engr-in-Charge. Make:- Bansal / M/s Calcutta poles ltd.

Supply and fix HT 11 KV, 150 mm height and 150 mm dia pin type insulator, porcelain, vitreous, white/brown/green, conforming to IS-2486 for 11000 Volts grade including one galvanised mild steel spindle, two galvanised iron washers and one galvanised iron nut etc complete all as specified and directed.

M&L for MS works such as cross arms, bracings, supports, clamps and back plates fabricated from structural steel section including nuts, bolts, washers, welding, bending, cold or hot, drilling holes for bolts, in any shape or size as indicated or directed and inclusive of one primer coat, one under coat and one finishing coat of synthetic enamel paint etc complete all as specified and as directed.

Supply and fixing air break switch, gang operated triple pole, mechanically operated, mounted on insulator and steel frame, with operating mechanism worked from ground level suitable for Horizontal or Vertical mounting fixed type, for current rating upto 200 amps suitable for 11000 Volts grade complete all as specified and as directed.

Materials and labour for danger notice plate of 1.6mm thick mild steel sheet, vitreous enameled white, with letters, figures and conventional skull and bones in signal red colour and fixed with MS clamps, bolts and nuts of approved size for HT, 25 x 20 cm size complete all as specified and directed.

M&L Stay assembly 20 mm stay rod complete with accessories as shown in electrical plate No 1 including loop type insulator, stay clamps, excavation and concrete etc compelte all as specified and directed.

M L MS works for anti-climbing device, spike type fabricated from MS bars(round, square and flat) including nuts, bolts, washers and welding in two halves made to shape to suit the cross section of the pole and including painting with two coats of aluminium paint over a coat of red oxide zinc chrome primer complete all as specified and directed.

Supply, laying or fixing 100 mm bore GI tubing, medium grade, ISI marked with all fittings for passing of cables laid in trenches or fixed to walls/poles complete all as specified and as directed.

Supply, install, testing and commissioning lightning arresters expulsion type complete with all fittings, suitable for 11000 volts, transmission class of discharge capacity 65 Kilo Amps etc complete all as specified and as directed.

M&L for PCC (1:3:6) type C-1 (using 20mm graded stone aggregate) as in coping of poles including necessary formwork etc complete all as specified and directed.

M&L for PCC (1:4:8) type D-2(using 40mm gr aggregate) as in foundation , filling and mass concrete etc complete all as specified and directed.

Supply ,install and testing copper wound Transformer step up / step down, outdoor type 100 KVA complete with standard fittings, HT 11 KV 3 Phase, LT 433 volts, 3 Phase 4 wire with off load tappings on HT side to vary secondary voltage within limit with Oil all as per IS:2026 of capacity 100 KVA inculding complete all as specified and as directed. Note-1. The rates include for supplying transformers with standard fittings and installing complete including all jointing materials, connecting with electrical system, earthing, testing and commissioning. Note-2. The transformer will have its initial oil filling to appropriate level (cost of oil including testing with desired dielectric strength included in ibid rates).

Supply, laying, connecting and testing XLPE HT under ground insulated (Earthed) cable laid in trenches/or fixed on pole etc. with screened PVC bedded galvanized steel strip or wire armoured electric power cable (heavy duty) with stranded aluminium conductor, 1100 Volt grade, cross sectional area 120 Sqmm, 3 Core conforming to IS-7098 (Part-II)-1985 complete all as specified and directed. Notes: (i) Excavation & necessary earth work shall be measured and paid separately.

Supply and fix Cable jointing kit for 11 KV (Earthed) grade cable for indoor termination heat shrink type joint complete with jointing material and accessories suitable for 3 core XLPE armoured aluminium conductor cable of size 120 to 185 sqmm etc complete all as specified and as directed by Engr-in-Charge.

Supply, laying, connecting and testing XLPE under ground insulated (Earthed) cable laid in trenches/or fixed on pole etc. with screened PVC bedded galvanized steel strip or wire armoured electric power cable (heavy duty) with stranded aluminium conductor, 1100 Volt grade, cross sectional area 70 Sqmm, 3.5 Core conforming to IS-7098 (Part-II)-1985 complete all as specified and directed. Note: Excavation & necessary earth work shall be measured and paid separately.

M&L for Automatic Power Factor Correction (APFC) Panel for 3 Phase, 415 V & 50 Hz system of capacity 50 KVAR, 6 stage type with suitable incoming MCCBs etc complete all as specified and as directed.

Supply, install, testing and commissioning Automatic three phase 100 KVA DG AMF ( Auto Mains Failure) Panel with in house control for DG parameters like low lube protection, High winding temperature, low fuel , DG over speed with both auto and manual mode etc complete all as specified and as directed by Engineer in charge.

Supply, install , testing and commissioning of outdoor LT distribution feeder pillar IP-65 , CPRI approved of suitable size factory made totally enclosed dust and vermin proof , double leaf shutter in front and single leaf shutter in rear made out of 3.15 mm thick CRCA sheet duly fabricated and having proper front and rear locking arrangement duly painted with powder coated paint and aluminium bus bar 200 amps, 415 volts, 50 Hz 3 phase and 4 wire system with the following items connected as under including supplying and fixing on MS channel 75mmx40mmx5mm in PCC foundation and PCC work around the panel board within two fit area:- (near Cottage no -RTG). INCOMING (a) MCCB 4 pole 200 Amps, 415 V, 35 KA-01 No (b) LCD multifunctioning meter-01 No (c) Phase indicator Lamps (RYB phases)-01 Set (Set of Three) LED Cluster type (d) CTs 100/5 amps-set of three (e) Aluminium bus bar 300 Amps-03 Nos and 150 Amps -01 Nos (f) Internal Wiring for panel incl insulators, sleeves etc OUTGOING (a) MCCB 4 pole160 Amps, 415 V, 25 KA-03 No (b) MCCB 4 Pole 100 Amps, 415 V, 25 KA-02 No Note:- The contractor shall have to submit documentry evidence in support of authorisation of CPRI approved.

M&L for electrical Earthing complete with GI plate electrode of size 60 Cm X 60 Cm X 6.3 mm thick burried directly in ground vertically at a depth not less than 2.25 mtr. below normal ground level, with top edge of earth plate at a depth not less than 1.5 mtr. below normal ground level , connected to GI earth strip 32mm x 6mm earth lead by means of bolts, nuts and washers of galvanised iron , earth lead strip protected by means of 32 mm bore dia light grade GI pipe up to switch board / panel board , all as specified and shown in MES schedule Electrical Plate No:-5 of SSR Part I, including excavation and earth work in any type of soil , PCC 1 : 2 : 4 type C1 in chamber , RCC 1:2:4 type C1 40 mmthick cover slab with 6 mm dia MS bars at 100 mm centre to centre both ways,with 6 mm dia MS hook, Charcoal dust, salt , funnel for watering complete and testing the Earth resistence and writing same on the chamber with synthetic enamel paint all as specified and as directed.

S&F Earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc. as required 32 x 6 mm galvanised iron strip with saddles and fixing screws etc for roof conductors and down conductors above ground including dismantling old unserviceable strip complete all as specified and directed by Engr-in-Charge.

M&L for maintenance free chemical earthing comprising of 17.2 mm dia molecularly copper bounded 250 mm micron on steel electrode 2.5 meter long each 03 nos per set, earth enhancing soil treatment compound TEREC + having essential chemical ingredients such as ionic chemical to provide stable low resistance for earth terminal to make it maintenance free ( TEREC + comes in 25 kg per bag required per set of chemical earthing ) HDPE earth pit cover medium duty to withstand 2000 kg load U clamp bolt for connecting copper strip ( minimum size of copper strip 25 x 3 mm -20 meter ) to earth rod.Note:- The subject item shall be executed at site by the authorised person or its agent. Approval of the same shall be obtained from Accepting Officer before execution.

S&F copper strip 20 x 3.15 mm with saddles and fixing screws etc for roof conductors and down conductors above ground etc complete all as specified and as directed.

Material and labour for sub main wiring with two single core 4.0 sqmm FRLSH, ISI marked PVC insulated multi stranded, unsheathed copper conductor cable and one single core unsheathed FRLSH , ISI marked, PVC insulated multistranded copper conductor cable of size 4.0 sqmm green colour as earth lead including PVC casing capping of suitable size including taking down old unserviceable one complete all as specified and directed, .(Note: two run of 4.0 sqmm cable , one run of earth wire of 4.0 sqmm and one run of PVC casing capping shall be measured as one length).Make- Cable- Finolex/RR cable/KEI, PVC Casing Capping- Presto plast/Finolex/Kalinga.

S&F sheet metal enclosure with socket and MCB SPN enclosure with two pin and earth plug and socket complete with one single pole MCB 240 V 20 Amps etc complete all as specified and as directed.

Supply, Install and testing Hi wall split Air conditioner units indoor / outdoor complete with cordless remote control unit with in built heating and cooling arrangement and with in built air ioniser and plasma filter for better indoor air quality of capacity 1.5 TR,BEE 5 star rating , energy efficient etc complete all as specified and as directed.Make :- VOLTAS ALL WEATHER SPLIT AC 18 H SZS 1.5 TON HOT & COLD or equivalent make in LG / DAIKIN / SAMSUNG / BLUESTAR.

Supply, Install and testing Voltage stablizer for automatic operation, single phase naturally air cooled indoor type & designed for input variation between 130 V to 300 V with output voltage stabilized at 230 V with accuracy of +/- 2.5% and of capacity 4 KVA etc complete all as specified and as directed.Make :- V-Guard VGX 400 or equivalent make in SEN & PANDIT / VENUS.

Supply and fix in repair MCCB DB 4 way vertical sheet metal enclosure TPN, 415 volts, double door with 100 Amps standard bus bar of suitable size , fixed on wall duly grouted in solid block wall or on wooden board with necessary electric connection etc complete all as specified and as directed. (Make:- Havells cat No :DHDLVDRWAOF004 or equivalent make as Seimens /Legrand / L&T .

Supply, laying XLPE insulated PVC inner sheathed, armoured with galvanized steel strip or wire heavy duty underground cable with stranded aluminum conductor 1100 volt grade of size 25 Sqmm 3.5 Core, confirming to IS, laid in trenches / duct passing through pipe / duct or fixed on pole and connecting and testing including taking down old unserviceable one complete all as specified and directed.

Supply and laying GI tubing light grade,50 mm bore , fixed complete to walls and ceiling or laid in floor for cable crossing complete all as specified and as directed

Supply and fix in repair MCB Distribution board , 240 volts single pole and neutral ,double door, sheet steel, enclosure powder coated with 200 Amps rated busbar with neutral link, 4 ways , fixed on wall duly grouted in solid block wall or on wooden board with electrical connection complete all as specified and directed. Make: Havells Cat part No DHDPSHODRW04 or equivalent in Schnieder/GE/C&S.

Supply and fix in repairs MCB 'C' series , four pole 415 V, 100 Amps 10 kA etc complete all as specified and as directed.Make : Havells / Schneider / Indoasian / Legrand.

Supply and fix in repairs MCB 'C' series , three pole 415 V, 100 Amps 10 kA etc complete all as specified and as directed.Make : Havells / Schneider / Indoasian / Legrand.

Supply and fix in repairs MCB , SPN , 240 V, 40 Amps 10 kA etc complete all as specified and as directed.Make : Havells / Schneider / Indoasian / Legrand.

Supply and fix in repairs MCB , SP , 240 V, 40 Amps 10 kA etc complete all as specified and as directed.Make : Havells / Schneider / Indoasian / Legrand.

Supply and fix Air Conditioner stand or shelf bracket ( steel) suitable for outdoor unit 1.5 ton including all necessary fixture etc complete all as specified and as directed.

Supply and fix Copper suction and discharge pipe for insulation suitable for Air Conditioner 1.5 / 2.0 Ton , super quality etc complete all as specified and as directed

Supply and fix in repair 25 mm bore PVC drain pipe , fixed on wall / roof / with necessary GI clamp or hook etc complete all as specified and as directed

Taking up or down steel tubing with connections including cleaning for refixing or removal from site with all fittings complete all as specified and directed. of following bore(s) of pipe :- (Note - 1:- excavation will be measured and paid seperately under relevant items. ) (a) 50 mm dia

(b) All as per item no. 72.00 here in above but of 40 mm dia

© All as per item no. 72.00 here in above but of 25 mm dia

Supply , laying and connection in trenches GI tubing , medium grade, including fittings such as tee, bend, nipple, socket, reducer, flange, union etc complete all as directed by Engr in Charge of following bore (s) of pipe:- (a) 50 mm dia Note - 1:- excavation will be measured and paid seperately under relevant items. )

(b) All as per item no. 75.00 here in above but of 40 mm dia

© All as per item no. 75.00 here in above but of 25 mm bore

S&F in repair Gun metal gate valve class I (ISI) marked with iron wheel head, screwed both ends for iron pipe, complete all as specified and directed by Engr-in-Charge for the following bore (s) of pipe:- (a) 50 mm bore

(b) All as per item no.78.00 here in above but of 40 mm bore

© All as per item no.78.00 here in above but of 25 mm bore

M&L for construction of Block masonry valve pit of size 600 mm x 600 mm x 600 mm (internal dimension) complete with MS angle iron frame work ( angle size 40 x 40 x 6 mm ) , 3 mm thick MS shet top cover , openable through hinges including necessary locking arrangement , rendering 15 mm thick cement mortar 1:4 on inside and exposed external surface in two layers (5+10) mixed with water proofing compound, and painting steel surfaces with two coats of bituminous paint inside and on exposed surfaces complete all as specified and shown in Drg No. TD/EM/6 Sheet 1/2 & 2/2 including dismantling old unserviceable one.

Supply & Fixing Hanging LED Pendant light ,Elegant desing with premium chrome finish, Easy height adjustment during installation, recommended to use with energy saving lamp complete with holder, necessary fixing arrengements, 9 watt LED lamp etc complete all as specified and as directed by Engr-in Charge. Make- Havells cat No LHFXAFN1TN1C060 or equivalent make in CG / Bajaj.

Supply & Fixing Energy Saver inverter lamp 9 watt B22, 6500 k, 220-240 Volt etc complete all as specified and as directed by Engr-in Charge. Make- Havells / CG / Bajaj / Philips.

Supply and fixing LED security Building light LED 45 Watt , pressure die cast aluminum housing, heat resistant glass, IP65 protection, better optics for uniform distribtion complete with all accessories internally pre wired and including connecting up with three core 1.5 sqmm flexible copper conductor cable FRLSH from ceiling rose to connector of light including suitable size bracket complete all as specified and as directed..Make Make:- Bajaj / havells/CG .

Supply,laying, and testing XLPE cable insulated,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with starnded aluminium conductor of size 16 sqmm 4 core etc complete all as specfied and directed.Make:- Havells / KEI / Fusion.

Supply and erecting steel tubular swaged pole 8.5 meter long type 410 SP-22 complete with cast iron base plate and final taper plug duly painted with anti corrosive paint internally and externally and upto 1.5 m length of pole above ground level (externally) shall be painted with two coats of synthetic enamel paint in strips of 30 Cm length, black and yellow alternatively and balance of pole with two coats of aluminium paint etc complete all as specified and as directed by Engr-in-Charge. Make:- Bansal / M/s Calcutta poles ltd.

Supply and fixing LED Flood light 50 watt , pressure die cast aluminum housing, heat resistant glass, IP65 protection, better optics for uniform distribtion complete with all accessories internally pre wired and including connecting up with three core 1.5 sqmm flexible copper conductor cable FRLSH from ceiling rose to connector of light including suitable size bracket etc complete all as specified and directed..Make Bajaj / Havells / CG

Supply & fixing Factory made IP-65 (Dust and power jet proof according to IEC60529) transparent street light junction box of size 167 mm x 125 mm x 82 mm made of high quality polycarbonate (shock proof, rust free, corrosion free acid and chemical resistant , fire retardant , fire retardant having high impact (IK 08) totally insulated, UV resistant ) having high grade gasket made of polyurethane and one no of MCB SP 10 Amps with two cable gland for cable FRLSH size 16 sqmm etc and fixing on pole with MS flat iron of size 20X3mm with necessary nut & bolts including complete all as specified and directed Make:Hensel Cat No K9105 or equivalent in Sentex

S&F PVC Cable of size 3 core 2.5 Sqmm PVC insulated , un sheathed , multi stranded copper conductor cables FRLSH in 20 mm PVC conduit including clamp and connecting up to street light fitting etc complete all as specified and as directed.

Material and labour for Point wiring with 1.50 Sqmm single core PVC insulated , unsheathed cable FRLSH, 1100 volt grade with multi stranded copper conductor drawn through and incuding medium grade, ISI marked, PVC conduit not less than 20 mm dia with accessories,cassing capping on wall/ceiling and incuding provision of 1.50 Sqmm single core PVC insulated , unsheathed cable FRLSH, 1100 volt grade with multi stranded copper conductor green colour as earth continuity conductor and connected to common earth dolly with suitable size of lugs, including mild steel sunken box/metal flush box with suitable modular or pressed steel terminal boxes made out of 1.6 mm thick mild steel sheet metal conforming to IS-5139(pt-I) of 1969 and IS:14772-2000 with earth dolly and coated with two coats of anti corrosive paint over a coat of red oxide primer both internally and externally including provision of new 3 mm thick plastic laminated sheet top cover for housing the switches , socket outlets, fan regulators etc. with brass screws and brass washers and making good the disturbed surfaces as per existing for one light point controlled by one switch i etc complete all as specified and as directed. Note :- Switch, socket and fan regulators to be measured and paid for separately . PVC Conduit confirming to IS 9537 part I & III .Note (All chases will be cut by chase cutter only) .Make of cable:- KEI / RR Kabel / Havells . PVC Casing & Capping:- Prestoplast / Finolex / Kalinga

Supply and fixing and testing Exhaust fan 250 mm sweep with louvers, AC single phase, including electrical connection with twisted 3 core PVC insulated flexible cord of size 0.75mm copper conductor FRLSH from ceiling rose including cutting holes in brick or PCC block wall and making good to disturbed surfaces with cement sand mortar 1:4 including necessary colour wash / distemper to match with the existing shade of the wall and necessary electric connection etc complete all as specified and directed. Make:- USHA ,model- CRISP AIR or equivalent make in CG / Bajaj / Havells.

Material and labour for sub main wiring with two single core 4.0 sqmm FRLSH, ISI marked PVC insulated multi stranded, unsheathed copper conductor cable and one single core unsheathed FRLSH , ISI marked, PVC insulated multistranded copper conductor cable of size 4.0 sqmm green colour as earth lead including PVC casing capping of suitable size complete all as specified and directed, .(Note: two run of 4.0 sqmm cable , one run of earth wire of 4.0 sqmm and one run of PVC casing capping shall be measured as one length).Make- Cable- Finolex/RR cable/KEI, PVC Casing Capping- Presto plast/Finolex/Kalinga.

Supply and fixr MCB, single pole 240 V, 6 to 40 Amps etc complete all as specified and as directed.Make : Havells / Schneider / Indoasian / Legrand.

Supply,laying, and testing XLPE cable insulated,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with starnded aluminium conductor of size 16 sqmm 2 core etc complete all as specfied and directed.Make:- Havells / KEI / Fusion.

Supply and fix isolator/ MCB DP, 240 Volts, 40 Amps, 10 kA rupturing capacity 'C' series complete all as specified and as directed. Make: Havells Cat part No - DHMCCDPF0040 or equivalent in Schnieder/GE/C&S.

Supply and fix Isolator MCB, single pole 240 V, 6 to 32 Amps etc complete all as specified and as directed.Make : Hager cat part no. NCN106N or equivalent make in Havells / Schneider / Indoasian / Legrand.

M/s A L Traders

kapoor and co