GE/BAS-79/2025-26 Special repair of building No P-30 (1 to 08) at Somnath enclave at Basoli under GE Basoli

Amount

Excavation in trenches n exc 1.5 m wide and nexc 1.5 m in depth for foundation or laying of UG cable/ pipe and getting out in any type of soil complete all as specified and directed.

M&L returning, filling and including spreading, levelling, watering and well ramming in layers not exceeding 25 cm complete all as specified and directed.

Removing excavated material nexc 50m and depositing where directed at a level nexc 1.5mtr above the starting point, complete all as specified and directed.

M&L Reinforced cement concrete M-20 (Nominal mix) using 20mm graded crushed stone aggregates as in slabs/shelves, supported on walls, beam and columns in floors and in shelves and the like including necessay for work complete all as specified and directed.

M&L TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Taking down chowkats or frames with shutter (without taking off shutter from the frames) n. exc 1.50 Sqm each complete all as specified and directed.

Taking down chowkats or frames with shutter (without taking off shutter from the frames) exc. 1.50 Sqm n.exc 4 Sqm each complete all as specified and directed.

S & F Aluminium (anodised) fixed type powder coated window fabricated from standard aluminium box sections all as specified and directed and comprising of the following :- a) Chowkhat / frame 100 x 44 x 1.5 mm thick b) Top, mid & bottom rail and styles 100x44x1.5 mm thick. c) Each Fixed Panel of area not exc 1.20 Sqm d) Panel of 4.8 to 5.0 mm thick heat observing glass pane (Make-Saint Gobain/ Modi float glass/ Hindustan Pilkington glass works) fixed with standard aluminium beading and rubber gaskets. e) The Rate should be incl of Fasterner and Taking Down Old window/ RCC Jalli. Note : All fittings are powder coated.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 65 x 125 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately).

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 65 x 100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately).

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately).

S&F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 35 mm size comprising of virgin polymer of K value 58-60 ,calcium carbonate and natural fibre and non toxic additives and resistance to spred of flame of Class A cateegory with property of being termite /borer proof ,water /moisture proof and fire retardant . WPC to be Laminated with PVC foil of minimum 14 microns thick of approval design pasted with hot melt adhesive on both faces of shutter and fixing with stainless butt hinges of required size with neccessary full body threated star headed counter sunk s.s screw shall ,all as per direction of enginner In charge.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30 mm size comprising of virgin polymer of K value 58-60 ,calcium carbonate and natural fibre and non toxic additives and resistance to spred of flame of Class A cateegory with property of being termite /borer proof ,water /moisture proof and fire retardant . WPC to be Laminated with PVC foil of minimum 14 microns thick of approval design pasted with hot melt adhesive on both faces of shutter and fixing with stainless butt hinges of required size with neccessary full body threated star headed counter sunk s.s screw shall ,all as per direction of enginner In charge.

Factory made fully glazed/wire gauge (single piece Both side) PVC prelam door shutter 35 mm thick (style) consisting of frame made out of mild steel tubes of size 19mm x 19 mm (19 gauge) for top and bottom rails and 19mm x 19 mm (19 gauge) in styles. Single Pieces plain coloured PVC sheets 5mm thick to be used to cover styles and rails PVC sheet strip of 20 mm width stuck inside with styles solvent cement for stiles & plain coloured PVC sheets for top rail, lock rail and bottom rail on either side side and as gap insert for top rail and bottom rail. Panel will be wire gauges and dtighten tig firmly and fitted as per manufactures instructions including Stainless steel wire cloth, 0.25 mm to 0.36mm nominal dia of wire & average width of aperture 1.40mm to to 2mm and Aluminum XPM in rhombus shape, in one Piece from top rail to bottom rail taking down with existing one all as specified and directed by Engineer-in-Charge. NOTE: All screws shall be self tapping chromium plated

S&F Butt hinges of stainless steel of size 100mm complete all as specified and directed.

S&F 2 lever Brass Mortice lock for cabinets/cupboard with fittings ,concelead type, size 100 mm including cutting holes,cover plate and other accessories complete all as specified and as directed.Make:-Hettich,Godrej Harrison or equivalent make.

S&F Stainless steel, barrel tower bolts size 150 mm of extruded section and fixed complete all as specified and directed.

S&F aluminium hanging floor door stopper,Twin rubber stopper,size 100mm , anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. complete all as specified and directed.

S&F Stainless steel handles, fabricated type, anodised Size-150mm, anodised section and fixed complete all as specified and directed.

S&F 300 mm long Stainless Steel, sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet cast or extruded section and fixing bolts and sliding bolts complete all as specified and directed.

S&F in repair continuous (piano) hinges,Width of flaps (when open) 30 mm heavy duty mild steel, bright finish or electrogalvanised sutable for 19mm thick shutter and fixed, complete all as specified and directed.

M&L for 50 mm magnetic catchers with brass body and striking plate including letting in as fixed complete all as specified and directed.

S& F Stainless Steel Peg set of six hooks size 50mm to 60mm complete all as specified and directed

S&F factory made 18-20 mm PVC Board (weight not less than 10.5 kg/Sqm) PVC backing with glossy finish, oil spill proof laminated manufacured by an ISO 9001-2008 certified company. One side prelaminated of approved colour and other side balancing plain white for kitchen cabinet/cupboard shutter complete as per manufacturer's specifications and drawing including dismantling old board with all accessories and as directed.

S&F factory made 18-20 mm PVC Board (weight not less than 10.5 kg/Sqm) PVC backing with glossy finish, oil spill proof laminated manufacured by an ISO 9001-2008 certified company, both side plain for shelf/Partitions/drawer complete all as per manufacturer's specifications, drawing including dismantling of old board with accessories etc and as directed.

S&F 18-20 mm Wide PVC exterior grade plain colour banding(edge beading) of min thickness 0.80 mm fixed with adhesive/ jointing complete to edges of boards as in cupboards shelves / drawers/ shutters all around, complete all as specified and directed.

S&F of 304-grade, SS trolley as pull out/plain shelves unit with minimum width x depth x height 17" x20"x8" inches) fixed with soft close telescopic s/s channels with min load bearing capacity of 35 kg and Aluminium 'G' type Profile Handle including all other accessories required, complete all as specified and directed. (Make: Hettich, Hafele, Godrej interio or equivalent)

S&F of 304-grade, SS trolley for plate/thalli storage unit with minimum width x depth x height 21"x20"x8" inches) fixed with soft close telescopic s/s channels with min load bearing capacity of 35 kg and Aluminium 'G' type Profile Handle incl all other accessories required, complete all as specified and directed. (Make: Hettich, Hafele, Godrej interio or equivalent).

S&F of 304-grade, SS trolley for vegetable/storage unit with minimum width x depth x height 21"x20"x8" inches) fixed with soft close telescopic s/s channels with min load bearing capacity of 35 kg and Aluminium 'G' type Profile Handle incl all other accessories required, complete all as specified and directed. (Make: Hettich, Hafele, Godrej interio or equivalent).

S&F of 304-grade, SS Massala pull out storage unit with minimum width x depth x height 08"x 20" x 21" (inches) with three shelves with depth of 20 inches each fixed with soft close telescopic s/s channels with min load bearing capacity of 35 kg and Aluminium 'G' type Profile Handle incl all other accessories required, complete all as specified and directed. (Make: Hettich, Hafele, Godrej interio or equivalent)

M&L for Aluminium 'G' Type Profile Handle 6" width for kitchen cabinet/ cupboard complete all as specified and as per sample kept in GE office. Make:-Hettich,Godrej Harrison or equivalent make.

S & F telescopic Ball Bearing Soft closing/slide drawer channels of steel 304 grade, rust free, size 20 inch with min load bearing capacity of 35 kg for kitchen cabinet/ cupboard/ almirah, complete all as specified and as per sample kept in GE office. Make:-Hettich,Godrej Harrison or equivalent make

S&F 5 mm thick PVC Ultra Violet chemical, glossymate finish 100% termite/water proof, fire retrandent Eco friendly soild board one side decorative choice laminate ,and other side balancing white as wall lining in kitchen cabinet, cupboard etc fixed with screws to steel/timber frame work including dismantling old board etc complete all as specified and directed.

Providing & fixing Windows/ ventilators fabricated from roll framed sections made of galvanized steel colour coated/ powder coated (Base steel as per IS 513 “D” quality galvanized as per IS 277 with zinc of 120 gms/Sqr. Mtr.) with total coated thickness of 0.60mm incl painting, with Frame section 72mm x 55mm, Mullion section 72mm x 50mm, Shutter Frame 47mm x 20mm, incl 5mm plain/figured float glass and wire mesh,handle, lock and other accessories with powder coated guard bars Grill of size 10mm sq. MS Bars and 6mm x 12mm MS flat fixed using fasteners etc complete all as specified and as directed.Make:ECO – 4000 Series Windows (Double Rebate) NCL Windoors, Tata, JSW or its equivalent.

M&L For Polycarbonate Acrylic sheet 2.5 mm thick of any colour/shade as in roof covering /clading to wall fixed with self taping screw .(Sample as approved & Kept in GE's sample room) complete all as specified and directed.

S&F Framed work such as grills,gratings, etc.. with ends of bars shouldered and/or riveted,or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed.

M& L applying water proofing membrane APP (Atactic Polypropylene Polymer) modified membrane with non-woven polyster reinforcement/mat with thermal insulation of weight not less than 3.6 kg/sqm and thickness not less than 3 mm (reinforced) with polyester Non woven fabric weighing not less than 160 gms per sqm , laid by torch application method with overlap 100 mm on length side and 150 mm on the width side over a solvent based bitumen primer @ 0.3 Ltr Sqm with one coat of aluminium paint over membrane surface by the same manufacturer conforming to IS:3384-1986 on prepared surfaces including 20 mm thick screed bed in cement mortar (1:4) even and fair & including taking out /demolition of old treatment complete and removal of debrises not exceeding 50 mtr and depositing where directed complete all as specified and directed. NOTE :- MOU to be submitted by the contractor beore starting of work with the authorised applicator by the OEM of APP membrane duly recommended by Engineer-in-charge.

M&L for cement concrete 1:2:4 type B-0 (using 12.5 mm graded crushed stone aggregate), top surface of plain concrete padding shall be finished even & fair w/o using extra cement complete all as specified and directed.

S&F in repair 110 mm bore PVC (SWR) Pipes single socketed in any length with rubber ring joints, laid in trenches complete all as specified and directed.

S&F in repair 75 mm bore PVC (SWR) Pipes single socketed in any length with rubber ring joints, laid in trenches complete all as specified and directed.

S&F in repair 110 mm bore PVC (SWR) Pipes single socketed in any length with rubber ring joints, fixed to wall complete all as specified and directed.

S&F in repair 75 mm bore PVC (SWR) Pipes single socketed in any length with rubber ring joints, fixed to wall complete all as specified and directed.

S&F PVC (SWR) Bends in any radius 110 mm bore in repair complete all as specified and directed.

S&F PVC (SWR) Bends in any radius 75 mm bore in repair complete all as specified and directed.

S&F PVC (SWR) Bends with access door in any radius 75 mm bore in repair complete all as specified and directed.

S&F PVC (SWR) Bends with access door in any radius 110 mm bore in repair complete all as specified and directed.

S&F in repair , PVC(SWR), junction single, (Single 'T' ) with access door equal or unequal for 75 mm bore , complete all as specified and directed

S&F in repair , PVC(SWR), junction single, (Single 'T' )with access door equal or unequal for 110 mm bore , complete all as specified and directed

S&F in repairs for 75mm bore PVC (SWR) floor trap plain with grating including jointing with solvent cement complete all as specified and directed.

M&L PVC (SWR) P trap 110 mm, setting and jointing with solvent cement complete all as specified and directed.

S & F in repair CP Brass bottle trap having minimum water seal 25 mm all as specified and directed.

S&F PVC (SWR) Vent cowl 75 mm bore in repair..complete all as specified and directed.

S&F in repair/new PVC connection 15mm size with PTMT nuts of length 450mm complete all as specified and directed.

S&F in repair Fancy type health faucet with 8mm dia 1mtr long flexible tube (back flow preventer), chromium plated of 15mm bore, complete all as specified and directed.

M&L for Rotational moulded polyethylene water storage tank 3 layer white colour water tank, non- toxic effect, algea formation protection (made from Virgin grade of polyetylene material which is duly stablized with anti-oxidentPlastic) of capacity 500 litres, (cylindrical vertical tanks with closed top,specific wt shall be 25 gm/ltr), the internal and external surfaces of tanks are smooth, clean and free from any hidden internal defects, hoisted and fixed in position including S & F necessary GI fittings, inlet/outlet washout, overflow pieces long nipples, checknuts & washer, 20 mm dia PTMT valves high pressure of PTMT with epoxy coated Aluminum rod & high-density plastic ball and 20 mm brass stop cock etc including taking down existing tank complete all as specified and directed.

Suppy and fix gate valve 20mm dia gun metal gate valve conforming to IS with iron wheel head screwed both ends for iron pipe complete all as specified and directed..

S&F in repair 15mm bore chromium plated cast copper alloy bib taps fancy type long body with crutch or butterfly handle screwed down screwed for iron pipe or for brass ferrule all complete all as specified and directed.

S&F in repair Wall Mixer System Complete, Connecting Legs & Flanges complete all as specified and directed.

S&F in repair Central Hole Basin Mixer without Popup Waste System with 450mm Long Braided Hoses Also available complete all as specified and directed.

S&F in repair Wall Mixer 3-in-1 System with Provision for Overhead Shower Complete with 115mm Long Bend Pipe on Upper Side, Connecting Legs & Flanges (without Hand & Overhead Shower) complete all as specified and directed.

S&F PVC shelves of PTMT fixed with and including chromium plated brass screws and plastic cleats. complete all as specified and directed.

S&F in repair brass chromium plated tubular towel rails 20mm dia D type 60cm long between flanges complete all as specified and directed.

S&F in repair Vitreous China, wash basin white, flat back , size 400mmx300 including brackets of any size, including cutting for and pinning in ends of brackets or erecting stand including fixing and supply of waste pipe of 32 mm dia, waste coupling of chromium plated brass. complete all as specified and directed .

S & F for vitreous China squatting pan, ‘Orissa’pattern, size 580 x 440 mm white, with integral foot rests including provision of lime concrete bedding (excluding flushing cistern and flush pipe complete all as specified and directed.

S&F in repair, Vitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe )with CI ‘P’ or ‘S’ trap including plastic seat cover , white, closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging device and jet spray complete all as specified and directed

S&F in repair PVC valveless,syphonic action type, flushing cistern, low level, white with inlet, ball valve, float and handle including brackets, PVC 32 mm 'L' bend of capacity 10.0 litres and making good to dismantled/damaged floor/surfaces, fixing in repair, complete all as specified and directed

S&F in repair sinks with drainage board made of stainless steel 1.00 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm & bowl size 410mm x 355mm x 200mm complete with CP waste coupling & PVC waste pipe complete all as specified and directed .

S & F in repair Kitchen stainless steel plate rack made out of 1 mm thick sheet and having partions as per sample. The over all size (30"x36"x10") fixed with steel fastners or steel screw complete all as specified and directed .

S&F of 15mm dia bore steel water GI tubes medium grade with all fittings and fixed cocealed to walls, ceilings or laid in floors complete with and including taking up or down 15mm bore steel water tubing and connections including cutting/chiesling of brick/concrete surface and making good as per existing complete all as specified and directed

Refixing of 15mm dia bore steel water GI tubes medium grade with all new fittings and fixed cocealed to walls, ceilings or laid in floors complete with and including taking up or down 15mm bore steel water tubing and connections including cutting/chiesling of brick/concrete surface and making good as per existing complete all as specified and directed.

S&F of 20mm dia bore steel water GI tubes medium grade with all fittings and fixed cocealed to walls, ceilings or laid in floors complete with and including taking up or down 20mm bore steel water tubing and connections including cutting/chiesling of brick/concrete surface and making good as per existing complete all as specified and directed

Refixing of 20mm dia bore steel water GI tubes medium grade with all new fittings and fixed cocealed to walls, ceilings or laid in floors complete with and including taking up or down 20mm bore steel water tubing and connections including cutting/chiesling of brick/concrete surface and making good as per existing complete all as specified and directed

S&F of 40mm dia bore steel water GI tubes heavy grade as laid in sunken floor complete all as specified and directed

Demolition of plain cement concrete in ground floors or above ground floor and paving n.exc 15 cm thickness (Below or above ground level) complete all as specified and directed.

M&L for demolition of Concrete (reinforced) of any description and in any position not otherwise specifically provided for complete all as specified and directed.

M&L for 100 mm thick PCC 1:3:6 type C-2, using 40 mm graded stone aggregate,as in subbase complete all as specified and directed.

M&L for machine pressed precast concrete colour interlocking paver block any shape and size confirming to IS 15658- 2006 0f 60mm thickness with grey cement and pigment, M-35 grade in and including 50mm thick layer of sand filling complete all as specified and directed.

M&L for PCC 1:5:10 type E-2 (using 40 mm graged crushed stone aggregate) as in foundation filling and mass concrete (sunken floors etc) complete all as specified and drected

M&L for (a) Rendering 15mm thick plaster in cement sand mortar (1:4) mixed with water proofing compound (confirm to IS-2645-Specification for integral cement water proofing compound) as approved as per manufacturer instruction, shall be applied both on floor and side walls. The surface shall be cured and allowed to dry, all the joints of pipe shall be sealed properly as per instruction of agency who is carying out water proofing treatment. (b) Apply a layer of APP modifeid membraneover a coat of oil bound bitumen primer @ 0.30 liter/Sqm on floor as well as on side wall as per manufacturer's instruction of make/Manufacurer as in spcified in Zonal Specification Part-II , After the treatment is over ,sunkun portion shall be kept full of water for atleast one week to check that no seepage is seen from the external surfaces complete all as specified and directed.

M&L for cement concrete type B-0 1:2:4 using (12.5 mm graded stone aggregates) 25 mm thick in flooring complete all as specified and directed.

M&L for screed bed or bedding layer of mortar 15mm thick in cement mortar 1:4 for laying floor finishes complete all as specified and directed.

M&L for 10mm thick rendering/screeding on fair faces of brick/concrete surfaces in cement mortar 1:4 and finished even and fair for receiving tiles complete all as specified and directed.

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L Glazed ceramic tiles in vertical surface 350x250mmx7mm/450X300X7mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface complete all as specified and directed.

Material and labour Non - skid Digital Ceramic joint less coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm , in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match and set in neat cement slurry and pointed with coloured/white cement to match the surface. (sample as approved & kept in GE's sample room) complete all as specified and directed.

Material and labour Non - skid Digital Ceramic joint less coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm , in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match and set in neat cement slurry and pointed with coloured/white cement to match the surface. (sample as approved & kept in GE's sample room) complete all as specified and directed.

Material and labour Non - skid Digital Ceramic joint less coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm , in skirting/dado etc set and jointed in neat cement slurry and pointed in white or coloured cement to match and set in neat cement slurry and pointed with coloured/white cement to match the surface. (sample as approved & kept in GE's sample room) complete all as specified and directed.

M&L for rendering 10mm thick in cement mortar 1:6, on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement, preparation of new plastered surfaces of walls and applying 1mm thick wall care putty, one coat of primer and two coat oil emulsion distemper on walls complete all as specified and directed.

Preparation of old decorated brick /concrete, plastered /un-plastered surfaces of ceilings, cornices etc by booming down with steel wire brushing, scrapping down smoke soot, moulds, moss, efflorescent salts, oil, greasy spots , rubbing with sand paper and applying two coat of white wash on ceiling, complete all as specified and directed.

M & L for Preparation of old decorated brick/concrete/ plastered/unplastered surfaces of walls, Pillars, cornices etc by booming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts, trading oil and greasy spots, rubbing with sand paper and applying one coat of oil bound distemper on walls, pillars, cornices surface including making good uneven surface/holes and smoothening of surface with 1mm thick birla wall care putty coloured in same shade where ever required etc. complete all as specified and directed.

M&L for preparation of new plastered surfaces of walls, chajjas, fascia, face of columns, beams etc. and applying two coat of weather proof smart exterior emulsion making good uneven surface/holes with Birla wall care putty coloured in same shade where ever required and over a coat of Primer etc (up to 2nd storey with necessary scaffolding) complete all as specified and directed. Note :- (Wall surface made smooth and application of emulsion through smart mechanical means)

Matrial and Labour for Complete Removal of Existing Treatment (Change of Colour Scheme) of Old plastered surfaces of walls, chajjas, fascia, face of columns, beams etc. and applying two coat of weather proof smart exterior emulsion making good uneven surface/holes with Birla wall care putty coloured in same shade where ever required and over a coat of Primer etc (up to 2nd storey with necessary scaffolding) complete all as specified and directed.

M&L for Granite black or any other colour 16-18mm thick (table rubbed and polished) in steps, jambs, pillars, window cills,cooking platform including Moulding, rounding , chamfering and making hole for Gas pipe and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixer of pigment to match with marble shade complete all as specified and directed.

M & L for 16-18 mm thick Granite (of any type) tiles machine cut, in skirting/ dado laid over cement screed and jointed with grey cement slurry, and pointed with white cement with admixture of pigment to match the shade of granite stone including 10 mm thick rendering 1:4, grinding and polishing complete all as specified and directed.

Taking down cement plaster on brick or concrete surface of any description including racking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

S&F in repair 25mm outer dia stainless steel decorative drapery rod of thickness 20 gauge and for every 01 RM length, with stainless steel brackets near to ends with stainless steel finials for 25mm dia drapery rod at both ends. The drapery rod shall be projecting 150 mm outer side from the clear opening of doors/windows. ( Including necessary fittings) Complete all as specified and directed.

S&F in repair 15mm bore angle valve with wall flange, cast copper alloy, chromium plated fancy type screwed for 15 mm iron pipe, complete all as specified and directed.

S&F in repair Stainless steel fancy type soap dish complete all as specified and directed.

S&F in repair chromium plated shower roses with or without swivel joints 125mm size including fixing to steel pipe or union complete all as specified and directed.

Demolition of brickwork built in cement mortar including all quions, arches, pillar complete all as specified and directed

M&L Brick work with sub class 'B' bricks straight or curved on plan exc 6m mean radius with old size bricks built in cement mortar 1:6, complete all as specified and directed

All as per item No above, but except brick complete all as specified and directed

M&L Brick work with sub class 'B' bricks straight or curved on plan exc 6m mean radius with old size bricks built in cement mortar 1:4, complete all as specified and directed

M & L for Half thick Brick wall work curved on plan in any radius with old size bricks built in cement mortar 1:4 and external pointed flush in same mortar as the work proceeds. complete all as specified and directed.

M&L for Rendering 15mm thick in cement mortar 1:4 on fair faces of brick work or conrete surfaces finishing the surface even and smooth without using extra cement mixed with liquid water proofing compound complete all as specified and directed

M&L for rendering 5 mm thick in CM (1:3) finished surface even and smooth w/o using extra cement in ceiling and applying three coats of white wash on ceiling complete all as specified and directed

Supply only integral Water Proofing Compound. complete all as specified and directed

Taking down, dismantling of broken/loose portion of chajja, facia upto 450 mm wide and making good the surfaces with cement mortar 1:3 or PCC 1:1.5:3 including necessary formwork/scffolding and matching with existing surface of facia (including white wash/colour wash or cement base paint) chajja upto 2nd floor complete all as specified and directed.

M & L Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required complete all as specified and directed

M&L precast Reinforced cement concrete 1:2:4 type B1 (using 20mm graded crushed stone aggregates) as in man hole covers set in cement mortar 1:6 all as specified and directed incl necessary form work. Note: Steel reinforcement shall be measured and paid for separately under respective items

M&L Cement concrete M-15 (Nominal mix), type B-2, 1:2:4, (using 40 mm graded crushed stone aggregates) in surface channel and drain etc complete all as specified and directed

Supply and laying for XLPE insulated, armoured, heavy duty electric cable with aluminum conductor, 1100 Volts grade, of size 35 Sqmm, 3.5 core complete all as specified and directed by Engr-in-Charge . Note: Earth work including excavation, returning filling , removing, sand cushioning, GI pipe,brick covering for mechanical protection of cable etc will be measured and paid for separately under respective items of schedule.

Supply & laying of approved quality sand under cable upto 15cm before laying the cable and 8cm over the cable after laying, punned down to overall thickness of 18cm in trenches for cable cushioning complete all as specified and directed. (Punned thickness shall be measured)

Material and labour for well burnt, old size Sub Class 'B' brick covering protection to the eletric cable laid dry flat transversally along the length of cable with width equal to length of brick complete all as specified and directed .

Supply and fixing in trenches/under roads/under floor/on walls in new position tubing GI Light grade of 40 mm nominal bore of pipe with screwed sockets joints (such as bends, elbow, tees, etc) complete all as specified and directed

Suppy and fix gate valve 50mm dia gun metal gate valve conforming to IS with iron wheel head screwed both ends for iron pipe complete all as specified and directed..

Suppy and fix gate valve 25mm dia gun metal gate valve conforming to IS with iron wheel head screwed both ends for iron pipe complete all as specified and directed..

S&F of 25mm dia bore steel water GI tubes medium grade with all fittings and fixed cocealed to walls, ceilings or laid in trenches including taking down existing old unserviceable tube complete complete all as specified and directed

Taking down copper/aluminum point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc. complete all as per specified and directed.

M & L for point wiring for one light point/fan point controlled by one switch with 1.5 sqmm single core PVC insulated unsheathed multistranded copper conductor (FRLS) in and including PVC concealed conduit having thicknes 1.8mm with all fittings, pressed sunken box thickness of sheet not less than 2mm thick suitable for modular switches , including 1.5 sqmm single core PVC insulated unsheathed multistranded copper conductor (FRLS) as earth continuity conductor connected to comman earth dolly in and including cutting chiseling for concealed piping as required and making good disturbed surface area and white wash /colour wash to matching with the existing colour complete all as specified and directed. Note: (a) Insulation test of point wiring (b) colour coding is to be maintained .(Ph-Red, N-Black, Half -Yellow, Earth- Green) (b) Rate for cutting chases for conduit and flushing metal boxes including making good the distrubed wall deemed included in quoted rates. (c) Modular switchs ,sockets ,cover plates and all connected accessories shall be paid seperatly in respective items .

All as per item No 121 but for one 3 pin 5 Amp socket outlet on independent board complete all as per specified and directed.

All as per item No 121 but for one 3 pin 5 Amp socket outlet on same board complete all as per specified and directed.

All as per item No 121 above but controlled by two way switches, with cable of 1.5 sqmm size complete all as per specified and directed.

Point wiring with 2.5 sqmm single core PVC insulated unsheathed multistranded copper conductor (FRLS) with in and including PVC concealed conduit with sunken box suitable for modular switches and sockets for 5 pin 15 amps socket outlet ,including 2.5 sqmm single core PVC insulated unsheathed multistranded copper conductor (FRLS) as earth continuity conductor connected to comman earth dolly in and including cutting chiseling for concealed piping and making good disturbed surface area and white wash /colour wash to matching with the existing colour and complete all as specified and directed. Note : (a) Insulation test of point wiring (b) colour coding is to be maintained (Ph-Red, N-Black,Earth- Green).

S&F modular switches one way 6 amps one module complete all as specified and directed .

S&F modular switches one way 16 amps with indicator one module complete all as specified and directed .

S&F modular socketes out let 6 amps 5 pin shuttered socket2 module complete all as specified and directed.

S&F modular socket outlet 16 amps, 3 Pin Shuttered Socket, 2 module complete all as specified and directed

S&F for modular switch two way 6A,1 module ,complete all as specified and directed.

S&F modular white cover platewith frame 8 modular complete all as specifed and directed.

S&F modular white cover platewith frame 6 modular complete all as specifed and directed.

S&F modular white cover platewith frame 4 modular complete all as specifed and directed.

S&F modular white cover platewith frame 3 modular complete all as specifed and directed.

S&F modular white cover platewith frame 2 modular complete all as specifed and directed.

Supplying&Fixing modular Bell push, 6 amp two module complete all as specifed and directed.

S&F modular fan step regulator,120 W two module complete all as specified directed.

S&F in repair/replacement bell ding dong type, complete all as specified and directed .

S & F lamp holder/batton holder/angle holder insulated body(Metal ring) with bakelite back plate suitable for batten fittings including 9 watts LED Lamp 6500 K complete all as specified and directed.

S&F ceiling rose surface 65x50mm three terminal with bakelite back plate complete all as specified and directed.

Supply and fixing LED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose of make : Philips ,cat part No :BN170C LED20S-6500 PSU L120 /Havells ,Cat part no : LUMILINEPLUSNEOBS20WLED865SPCSSIND/Crompton , cat part no : CCS-100-20-65-HL2-DP-NWH/ Orient ,cat part no :LBLN-20-C-SQ-AL complete all as specified and directed

Supply and fixing LED light fitting mirror type Surface mounting General Purpose LED Battens in Extruded Aluminium housing with suite variety of application areas with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete of Make : Havells, cat part no: LUMILINEPLUSBS10WLED865SPCSSIND/Crompton, cat part no : TCS-108-10-65-SL-DP-NWH/of make Orient , cat part no: LBLN-10-C-SQ complete all as specified and directed.

M & L for providing/cutting the round /square hole on the wall and supply and fixing propeller type AC ventilating fans(Metalic body ) Single phase , 230 volts 300 mm sweep including grouting and fixing the ragged bolts in wall for exhaust fan and louver shutter on the exhaust side wall (outer surface of the wall ) and connecting PVC insulated three core 1.5 SQMM copper cable from ceiling rose to exhaust fan motor and writing MES No with black synthetic enemel paint 2.0 cm high. Make of Exhaust fan - Havells ,model no : Ventil Air DS Green /Standard, model no :Refresh air - SPS/Khaitan , model No: Eurocap complete all as specified and directed .

M & L for providing/cutting the round /square hole on the wall and supply and fixing propeller type AC ventilating fans(Metalic body ) Single phase , 230 volts 230 mm sweep including grouting and fixing the ragged bolts in wall for exhaust fan and louver shutter on the exhaust side wall (outer surface of the wall ) and connecting PVC insulated three core 1.5 SQMM copper cable from ceiling rose to exhaust fan motor and writing MES No with black synthetic enemel paint 2.0 cm high. Make of Exhaust fan - Havells ,model no : Ventil Air DS Green /Standard, model no :Refresh air - SPS/Khaitan , model No: Eurocap complete all as specified and directed .

S&F for LED Bldg security lights of 35 Watt. 230 V having pressure die cast aluminium housing with system lumens efficency≥100 lumen/W IP-65 protection, IK-07 rating, inbuilt electronic driver with PF>0.95 including Gl bracket of suitable dia bend to shape and fixed to wall by means of clamps or nuts bolts and connecting up with three core twisted flexible copper conductor cable . Make of street light fitting - Bajaj, cat part no :ENXT P 35L WH PO PC SD/Havells ,cat part no :ENDURASUNDOWNSL35WLED765PASYBOPC/Wipro ,cat part no : LR08-501-XXX-57-XX/Crompton ,cat part no : TRP-400-35-57-SL-LM-NSR complete all as specified and directed.

S&F MCB SP 6-32 Amps with 10KA breaking capacity of 'B' series in distribution board complete all as per specified and directed.

S&F in replacement MCBs single pole and neutral (SPN)/isolator 32 Amps with 10 KA breaking capacity of 'B' series in distribution boards all as specified and directed.

M&L for SPN MCB DB 8 way sheet metal enclosures double door 230 V AC, 50 Hz AC with IP 43 and IK 09 rating having fully insulated copper busbar, neutral bar, earth bar and cable ties for cable management including polyuthrene gasket complete fixed flush in wall including cutting chases on wall for taking out old DB and fixing of new DB and making good disturbed surface of wall with cement mortar and finishes to match exisiting surface complete all as specified and directed.

Removing existing unserviceable DBs along with its enclosures old wiring in between DB's/main switch/meter & S & F factory fabricated sheet metal enclosures wall mounted type DB of size 1.25 m x 1.0m x 0.25m with 2mm thick CRCA sheet and applying two coats of synthetic enamel paint over one coat of red oxide zinc chrome primer suitable to accommodate and comprising of following :- (a) Taking down and re-fixing electric meter 9 Nos. (b) One number MCB VTPN DB 4 way single door with one No incoming MCCB 63 Amp TPN-01, 10 KA with and including following :- (i) MCB SP 32 Amp - 05 Nos (ii) MCB SP 6 Amp - 01 No (iii) Blank plates - 03 Nos (iv) Rewiring with PVC insulated unsheathed ISI marked 4 sqmm FRLS copper condutor connected in between DB's SP to electric meter etc complete all as specified and directed .

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor(BLDC) complete all as specified and directed

S&F sub main wiring with two run of single core (FRLS) PVC insulated and unsheathed cable with copper conductor (Multi strand) having nominal area 6.0 Sqmm drawing into and including PVC non metallic rigid conduit of adequate size and making electric connections including one run (FRLS) PVC insulated single core copper conductor cable 6.0 Sqmm as a earth continuity conductor(green colour) in and including in non metallic rigid PVC conduit, including cutting chases in brick wall, replastering and making good to match the existing specifications complete all as per specified and directed. Note :- (i) Rates are deemed to be included chases of conduit and sinking for boxes cutting and making holes in wall/floor for passing in or through conduit (ii) Two run of 6.00 sqmm single core (FRLS) PVC insulated copper conductor cable one run of 6.0 sqmm copper conductor cable (FRLS) as a earth lead and one run of PVC conduit of suitable size will be measured as a one unit.

M&L for Earthing complete with galvanized steel earth plate electrode 600x600x6mm thick buried directly in ground (Earth pit not less than 2.25 Metre deep below ground level) with top edge of the plate not less than 1.5 metre below normal ground level, connected to galvanized earth lead wire 4.0 mm dia by means of bolts, nuts, check nuts and washers of galvanized iron or steel all as shown in electrical plate No. 3 of SSR Part-I (2009) including filling of charcoal dust, common salt all around Earth plate upto 150mm, 20mm bore GI medium grade watering pipe, 15 mm bore light grade earth lead protection pipe upto main board, funnel with wiremesh, 40mm thick RCC 1:2:4 type B-1 using 20 mm graded crushed stone aggregate reinforced with suitable handle and angle iron frame and necessary excavation and earth work in any type of soil etc. complete all as specified and as directed including testing on completion. (Note: The rate quoted include cost of min 7.5 metre earthling wire)

M/S OM SAI RAM BUILDERS (BID ID -3481090)

M/S SURINDER KUMAR MAHAJAN (BID ID -3481271)

KALSI CONSTRUCTION CO (BID ID -3481646)

Standard engineers (BID ID -3481105)

M/S MAHAJAN ENTERPRISES (BID ID -3481399)

SATISH AND CO (BID ID -3481346)

RATTAN CHAND CHANDAN AND CO (BID ID -3481508)

Ms International Engineers (BID ID -3481600)