PROVN OF CERATIN MINOR WORKS AT VIKRAM VIHAR UNDER AGE B/R-I OF GE (SOUTH) DELHI CANTT-10

Amount

Taking down chowkhats or frames with shutter exceeding 1.5 sqm and not exceeding 4.00 sqm each but without taking off shutters from the frame including removing complete all as specified and as directed.

All as per item 1.00 here-in-before but not exceeding 1.5 sqm each.

Dismantling wrought iron or mild steel work of any description not otherwise provided for windows grill complete all as specified and as directed.

S&Faluminum window fabricated with powder coated (minimum thickness of powder coating 50 micron) anodized aluminum frame of section 63.5mm x 38.10mm x1.5mm thick, shutter with section 47.62mmx44.45mmx1.5mm thick including aluminum anodized “D “ handle, hinges, peg stays, tower bolts, etc including jointing cleats for fixing builder's hardware fittings & stainless steel wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples including necessary fittings/fixture /aluminum snap beads complete all as specified and as directed. Note: Measurement shall be taken for clear opening i.e. out to out of window frame as a whole including all fittings and fixtures and no extra shall be paid separately.

S&F factory made Aluminium window as per TD drg No. CEDZ/D-316 with following specifications complete all as specified and as directed: (i) outer frame of size 40mmx114mm with 1.3mm thickness, corner 45 degree cut aluminium welded (ii) center mullion of size 40mmx65mm (iii) welded shutter (02 nos) of size size 40mmx60mmx1.3mm thickness 45 degree cut mechanically joint with 6mm allen key bolt clamp with 5mm clear glass both side EPDM rubber gasket metal body hand lever type single point lock, aluminium kobra hinges 2 Nos per shutter (iv) SS 202 grade 12 mm round bar safety grill at 100 mm c/c distance modified to 150mm c/c distance in front of handle, welded at both ends with 6mm SS 202 grade round bar (v) Welded wire mesh shutter (02 nos) of size 40x18mmx1.3mm thickness 45 degree cut with 0.45mm nominal dia of SS wire mesh, SS 75mm long hinges & PVC magnet. (vi) Entire window shall be powder coated with pure polyster coat of any shade as approved by GE (vii) Window shall have provision for installation of window AC/Desert Cooler and provn of window glass shutter, wire mesh, grill and necessary fittings and locking arrangement for subject portion will be modified as per ground requirement during the execution as per direction of Engr-in-charge. (viii) Window shall be installed with silicone complete all as specified and directed by Engr-in-charge. Note: Measurement shall be taken for clear opening i.e. out to out of window frame as a whole including all fittings and fixtures and no extra shall be paid separately.

M&L poweder coated aluminium anodised three way track sliding windows of frame size 92 mm x 31.75 mm x 1.5mm thickness (section no. 20831 of JINDAL) and of shutter size 40 mm x 18 (with 9.00 mm interlocking legs) x 1.45 mm thick (section no. 20737 of JINDAL) section (two shutter glazed, covering half of span of opening each & one shutter sketlon covering half of span of opening ) incl provn for making windows air tight, including 95mm aluminium handle with spring lock , stainless steel wire cloth, 0.45 mm nominal dia of wire and average width of aperature 1.4mm and fixed with steel wire stapples and 5 mm thick plain glass including necessary fitting/ fixture/ aluminium snap beads complete all as specified and as directed. Note:- Measurement shall be taken for clear opening i.e. out to out of window frame as a whole including all fittings and fixtures and no extra shall be paid separately.

S&F Stainless steel wire cloth 0.36 mm nominal dia of wire and avg aparture 1.4mm and fitted with tinned tacks or galvanised wire stapple complete all as specified and as directed.

M&L for 6mm dia powder coated aluminium decco grill, (minimum thickness of powder coating 50 micron), section No-104, 100mm aperture of hexagonal design and pattern as approved complete all as specified and as directed.

S&F powder coated (minimum thickness of powder coating 50 micron) aluminium frame of desired section as per site requirement for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc complete all as specified and as directed.

Surface excavation in soft/loose soil, not exceeding 30 cm deep and averaging 15cm deep and getting out complete all as specified and as directed.

Excavation in trenches not exceeding 1.5 m wide & not exceeding 1.5 m in depth for foundation/drain sewage lines etc in hard/dense soil complete all as specified and as directed.

M&L for 100 mm thick cement concrete 1:4:8 type D-2 (using 40 mm graded crushed stone aggregate) as in sub base complete all as specified and as directed.

M&L for 75 mm thick cement concrete 1:4:8 type D-2 (using 40 mm graded stone crushed stone aggregate) as in sub base complete all as specified and as directed.

M & L for machine pressed precast concrete interlocking paver block 60 mm thick of M-35 Grade with grey cement and pigment, any shape and size yellow/red colour confirming to IS 15658-2006 complete all as specified and as directed.

M&L for machine pressed precast concrete inter locking paver block 80 mm thick M-40 grade with grey cement and pigment & glossy finished any shape colour size complete all as specified and as directed.

M&L for sand cushion for laying interlocking paver block including watering and well ramming complete all as specified and as directed.

M&L for glossy finished coloured Chequered cement concrete tiles 30cm x 30cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors including 20 mm thick screed complete all as specified and as directed.

Removing of excavated material exceeding 250 m and not exceeding 500 mtr and depositing where directed complete all as specified and as directed.

Excavating in post holes in soft loose soil (or similar holes) each not exeedingc 0.5 cum, getting out , returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm complete all as specified and as directed.

M & for cutting holes into or through brick wall bult in cement mortar or cement lime mortar and stone walls n.exc 150 sq.cm including making good to the original surface complete all as specified and as directed.

M & L for cutting chases, pining in making good to facing where required and pinting in cement to, cutting not exc 10cm girth in brick walls complete all as specified and as directed.

S&F Structural Steel in roof, purlins crane of angle or other section gusset plates, Flat Iron rails braces etc, drilled for fixing, and other covering r etc to be prepared for hanging and sliding with and including either hooks and hinges and other covering running rails and guides and hanging also fastening and fixing complete. Fe- 410 Grade E-250 quality -Bl complete all as specified and as directed.

S&F steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St.-240 complete all as specified and as directed.

S&F Pre-printed galvalume aluminium zink coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof overing/cladding to wall, fixed with self tapping screw complete all as specified and as directed.

M&L for cement Concrete Type B1 1:2:4( using 20 mm graded crushed stone aggregate) as in roof Kerbs or mud stops, rounded or chamfered on edges complete all as specified and as directed.

M & L for applying two coats of synthetic enamel paint over a coat of red oxide primer on newly steel surfaces of any description over 10 cm in width or grith, not otherwise described including preparation of surfaces complete all as specified and as directed.

Taking down cement plaster on brick/concrete surface including racking out joints hacking for key scrubbing down with water etc complete all as specified and as directed.

M&L for Brick work with sub class B bricks straight or curved on plan exceeding 6 m mean radius built in cement mortar 1:6 complete all as Specified and as directed

M&L for 15 mm thick cement mortar plaster on brick or concrete surfaces in cement mortar 1:4 finished even and smooth surface wihtout using extra cement on internal wall of upto four stories bldgs complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the primess complete all as specified and as directed.

M&L for non skid jointless coloured ceramic tiles 300 x 300 x 7 to 8 mm thick, in floors etc set & jointed in neat cement slurry & pointed in coloured cement to match over and including 15 mm thick screed bed in cement mortar 1:6 for laying floor finish complete all as specified and as directed.

M&L for coloured glazed ceramic tiles 300mm x 250mm / 450 mm X350mm, 7 to 8 mm thick as in dado/ skirting,set and jointed in neat cement slurry & pointed in coloured cement includind 10 mm thick backing coat in cement mortore 1:4 complete all as specified and as directed.

M&L non skid coloured ceramic tiles jointless 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, as in floors etc set & jointed in neat cement slurry & pointed in coloured cement to match over and including 15 mm thick screed bed in cement mortar 1:6 for laying of floor finish and including roughning of old PCC flooring complete all as specified and as directed.

M&L for preparation of surface by complete removal of existing treatment, wahsing down and stopping of distempered and painted surfaces and old plastered or unplastered surfaces of wall and/ceiling applying two coats of distemper oil emulsion, white or tinted over & including a coat of 2 mm thick wall care putty complete all as specified and as directed.

M&L for complete removal of existing treatment by mechanical means and applying water proof wall care putty to achieve even and smooth surface and then applying two coat of 100% anti fungal acrylic emulsion exterior grade weather proof paint over and including one coat of exterior primer on wall/ceiling complete all as specified and as directed.

M&L for preparation of newly plastered surfaces on external wall/ ceiling, applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/ litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade(Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 Sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 Sqm and including 2 mm thick water proof wall care putty complete all as specified and as directed.

M&L for Preparing new plastered surfaces of wall and applying two coats of distemper oil emulsion, over a coat white or tinted over & including a coat of 2 mm thick wall care Putty complete all as specified and as directed.

Fixing only chain link fencing incl line wires any mesh size & type to any type of standards rails straining bolts etc. incl provision of binding wire complete all as specified and as directed.

Supply only chain link MS galavnised fencing 50mm squre mesh with 10 gauge complete all as specified and as directed.

S&F in repairs brass CP Wall mixer for mixing Hot and cold water screwed down for iron pipe complete all as specified and as directed.

S&F PVC modular type kicthen frame with PVC laminated shutter including Piano type hinges, 02 Nos handle , 02 Nos Knob for each shutters and shelves alonwith all fittings and fixtures complete all as specified and as directed.

M & L for treatment of soil under existing floor through above the skirting using emulsion termin or equivalent anti termite treatment making the the holes @ 300 mm center to center along the internal wall, 50 mm deep including drilling and plugging 12 mm dia holes with sealed coloured cement to match the existing skirting of the wall complete all as specified and as directed.

M&L for treatment of existing floors spray with pressure gun machine using emulsion Termin or equivalent Anti Termite Treatment complete all as specified and as directed. Notes for Srl item Nos.43.00 & 44.00:- (i) The work of anti termite treatment shall be got executed by the contractor through an approval agency (as approved by the GE) who is a member of PCAI (Pest Control Association of India) holding valid license as per clause 12 of insecticides Act, 1968 and persons employed to do the antitermite treatment shall be qualified as per Rule 10 of the Rules framed under insecticides Rules 1991 (ii) The contractor shall stand guarantee to the Government for a period of 10 years from the certified date of completion of work. The contractor shall furnish a written guarantee for the effectiveness of the treatment for a period of ten years in favour of GE. (iii) 2.5% of work done amount of this item shall be retained from contractors payment for a period of 10 years reckoned from date of physical completion of this work, or in lieu contractor may deposit bank FDR for the said amount for 10 years which shall be released.

M&L for 18 mm thick wood plastic composites (WPC) board for shutters, 100% solid with density not less than 650 Kg per cubic meter , one side wood grain finished laminated for exposed/external surface , fixed with screws fitted under or above the kitchen cooking platform and/or other platform including all necessary fittings and fixtures like nickle plated clip hinges, knobs, channels etc complete all as specified and as directed. Notes : (a) Pattern & design of WPC board to be decided by GE. (b) Items like cupboard knobs, stainless steel channel, CP plate clip hinges to be paid in extra. (c) Locking arrangement shall be provided in rooms cupboard shutters. The rate quoted by the tenderer shall be included for the same.

M&L for Granite (of any type) tiles 12 mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete and including 15mm thick screed bed in cm 1:6 for laying floor finish complete all as specified and as directed.

M&L for coloured dark shade vetrified ceramic tiles 8 mm thick (square / regtangular) polished , area of each tiles not exceeding 0.72 sqm in floors etc and joineted neat in cement slurry and pointed in white or colour cement to match over and including 15mm thick screed bed in cement mortar 1:4 complete all as specified and as directed.

All as per item No.47.00 here-in-before, but on vertical surfaces such as skirtings, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10 mm thick plastering in cement mortar 1:4 on brick masonry surfaces complete all as specified and as directed.

Taking down shutter of any description exceeding 1.00 sqm not exceeding 2.00 sqm each and refixing the same opening including easing and adjusting the same complete all as specified and as directed.

M&L for preparing new plastered surfaces of wall and applying two coats of distemper oil emulsion, over a coat white or tinted over & including a coat of 2 mm thick wall care putty complete all as specified and as directed.

S&F in repairs vitreous china wash hand basin, white round shape size 520x450x200 mm (excluding taps, waste, pipe chain and plug) but including porcelain stopper and a pair of MS bracket etc complete all as specified and as directed.

S&F in repairs vitreous china wash hand basin, white flat back size 550x400mm (excluding taps, waste, pipe chain and plug) but including porcelain stopper and a pair of MS bracket etc complete all as specified and as directed.

S&F in repairs chromium plated brass angle valve suitable for 15 mm bore pipe complete all as specified and as directed.

S&F in repairs PVC connection 450 mm long with 2 Nos brass check nuts suitable for 15 mm bore of pipe with washer complete all as specified and as directed.

M&L for soap dish chromium plated brass fixed with brass nuts and screws as in repair complete all as specified and as directed.

M&L for toilet paper holder brass chromium plated as in repair complete all as specified and as directed.

S&F in repairs CP brass shower rose fancy type 125 mm size suitable for 15mm bore pipe complete all as specified and as directed.

S&F in repairs viterous china wash down water closet pan (Pedestal pattern) white incl 'P' or 'S' trap and making good the disturbed surface to match with the existing complete all as specified and as directed.

S&F in repair 12 mm thick prelaminatd particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete all as specified and as directed.

All as per item 59.00 here-in-before but 18/19 mm thick.

S&F 15mm bore GI tubes, medium grade galvanised, with all fittings and fixed complete to walls and ceilings or laid floors or concealed, including taking up or down 15mm bore steel tubing and connections and complete all as specified and as directed.

S&F (width of flaps 30 mm) Continuous (piano) hinges, mild steel, bright finish or electro galvanised complete all as specified and as directed.

S&F in repairs plastic water closet (EWC) seat cover white closed pattern with flat bottom and cover incl mild steel chromium plated hinging device complete all as specified and as directed.

S&F in repairs towel rail 600 mm long 20 mm dia aluminium anodised chromium plated fixed with wooden guities embeded in cement mortar (1 : 3) with steel screws etc complete all as specified and as directed.

S&F in factory made single extruded WPC (Wood Polymer Composite) solid frames or chowkhat of size 45 x 75 mm comprising of vigin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ricehusk/wheat husk) and non toxicadditives (maximum toxicity index of 12 for 100 g,s) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of class A category with property of being termite/ borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete all as specified and as directed. Note:- For WPC solid frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

M&L for 18 mm thick wood plastic composites (WPC) board for shutters, shelves with property of being termite/ borer proof, water/ moisture proof and fire retardant 100% solid with density not less than 650 Kg per cubic meter , one side wood grain finished laminated for exposed/external surface , fixed with screws fitted under or above the kitchen cooking platform including all necessary fittings and fixtures like nickle plated clip pieno hinges, knobs, channels etc complete all as specified and as directed. Note : Pattern & design of WPC board to be decided by GE

S&F PVC magnetic door catches of kitchen cabinet and similar work fixed with MS screws complete all as specified and as directed.

M & L for fabrication & fitting of modular kitchen with cabinet/ shelves & wardrobe/ cupboard made out of 18mm thick (one side decorative lamination & other side balancing lamination) PVC sheet with plano hinges including providing cabinet for keeping baskets / cutlery basket with handles / door shutters complete all as specified and as directed. Note :- PVC sheet, fitting & fixture will be measured and paid separetely as supply only.

Suppy only of 18mm thick UV coating, HDHMR board exterior grade, including acrylic high gloss sheet of 3mm thick over HDHMR board,anti fungal,moisture resistence,anti borer, as per IS 14587 for frame and shutter for kitchen cabinets/Cupboards etc complete all as specified and as directed. NOTE:- Sample as approved by Engineer-in-charge.

S&F 18mm thick UV coating, MDF board exterior grade, Both side laminated with any colour anti fungal,moisture resistence,anti borer, as per IS 14587 for kitchen/Cupboards shelfs fixing with 1st class hard wood lipping/beading etc complete all as specified and as directed. NOTE:- Sample as approved by Engineer-in-charge.

S&F soft close clip hinge bright finish complete all as specified & as directed.

S&F 125 mm dia oval shape brass handle fancy type bright finish complete all as specified and as directed.

S&F stainless steel basket (plain) of approved quality of size 520 x 485 x 100 mm complete all as specified and as directed.

S&F stainless steel glass basket of approved quality of size 520 x 485 x 150 mm complete all as specified and as directed.

S&F stainless steel two shelf pull out basket of approved quality of size 520 x 485 x 150 mm complete all as specified and as directed.

S&F stainless steel cutlery basket of approved quality of size 520 x 485 x 100 mm complete all as specified and as directed.

S&F repair of basket/ trolly channel 500mm long extruded MS galvanised over roller as per site required to make funcontional complete all as specified and as directed.

S&F (width of flaps 30 mm) Continuous (piano) hinges, mild steel, bright finish or electro galvanised complete all as specified and as directed.

S&F (width of flaps 30 mm )Continuous (piano) hinges, mild steel, bright finish or electro galvanised complete all as specified and as directed.

Notes :- (i) The contract sum shall be after deducting the amount of Credit shown in Sch of Credit of this Tender. (ii) If any item of same description in nature is found to be entered as "double in BOQ" and the bidder quotes different rates against same item, then the rate quoted on lower side shall be applicable and higher rate will not be allowed to be paid in any circumstances. No claims on this account shall be entertained on a later date.

M R INTERIOR HUB (BID ID -3271153)

UNIQUE BUILDERS (BID ID -3269335)

H S KALSI AND BROS (BID ID -3267283)

M/S.M.S.Devi.Const.Co (BID ID -3271773)