SPECIAL REPAIRS TO 02 DORMITORIES AT ABHI IV BLOCK (P 115) SPECIAL REPAIRS TO NBSC BLOCK (T 33) AND ADDITION ALTERATION TO COMMON BATHROOMS AT EKLAVYA BLOCK (P 34) AT INS MANDOVI

Amount

Dismantling/taking down existing hessain base fell or clay tiles or any other existing water proofing treatment from roof/chajja including cement plaster, cleaning the surface and removing the dismantled debris to a distance exceeding 1.50 km but not exe 5 km to outside the MD land and laying water proofing membrane treatment using 4mm thick APP modified membrane consisting five layer membranes withfeatures as specified, weighing not less than 4.00kg/sqm laid over a coat of cold bituminous primer @ 0.40 kg/sqm by torching the membrane and sealing the over lap by 100mm length side and 150mm width side all as per ,manufactures instructions including joints and changes in direction be curved with cement mortar 10mm thick 1:3 mixed with SBR latex @ 2.00ml/bag of cement curved well before laying of membrane, including applying two coats of solar reflective bituminous aluminium paint @ 0.10 litre/sqm all as per manufacturer instructions and to the satisfication of Eng-In-Charge: Note: (i) Irrespective of lap the net covered area will only be measured for payment.(ii) The quoted rate is deemed to be inclusive of bituminouus primer, APP membrane, Solar reflective bituminous aluminium paint & SBR latex.

M&L Cement concrete type B-0, 1:2:4 (12.5mm graded aggregate), 25mm thick on concrete surface over top of RCC roof with using waterproofing compund as per manufacture instruction finished even & fair with using extra cement complete all as specified and as directed. Note: Waterproofing will not be measured seperately.

Taking down cement plaster on brick wall stone wall etc including raking out joints, hacking for key securing down with water etc complete all as specified and as directed.

M&L for Dubbing out average 15mm thick in CM 1:6 on irregular face of walls (when specifically rendered in writing) complete all as specified and as directed.

M & L for rendering 10 mm thick in cement mortar 1:6 on fair faces of brick work or concrete surfaces finish even & smooth with using extra cement complete all as specified and as directed.

M&L for preparation of newly plastered surfaces and applying two coats of oil emulsion distemper , white or tinted including a coat of alkali resistant priming paint before distemper over and icluding 1mm thick wall care putty on walls complete all as specified and as directed.

M & L for 15 mm thick rendering in cement mortar 1:4 on fair faces of brick work or concrete surface with liquid WPC as per manufacturer instruction and finished surface even and smooth without using extra cement complete all as specified and directed (Note - liquid WPC shall not be measured and paid separately)

M&L for preparation newly plastered surfaces and applying two coats of acrylic emulsion (Anti fungal paint-APEX or equivalent) weather proof exterior paint over a coat of wether proof primer on external surfaces of wall complete all as specified

M&L 5mm thick plastering in cement mortar 1:3 finished even & smooth, without using extra cement on ceiling complete all as specified and as directed.

M&L preparing newly plastered surfaces of ceiling and applying three coats of white wash

M&L for Clean existing reinforcement with wire/rotary wire brush, making the surfaces free from loose material dirt etc, complete, applying two coats of alkaline rust converting primer FEOVERT confirming to ASTM-B-117, on the rebars, including cleaning the reinforcement, wire brushing to remove loose rust spalls, with time interval of 6 hour between the coats and applying protective coating IPNET-RB complete all as specified and directed.

M&L for chipping , removing carefullly concrete work by low impact hammer ,breaker without damaging the structure & cleaning and disposal of debries outside the premises etc. complete all as specified and as directed. Note : Hard concrete shall not be removed by force.

S&F for wire netting of stainless steel wire 1.4 mm dia (size of mesh 25 mm ) fixed with tinned tacks of stainless steel wire staples, including necessary frame of steel all as specified and directed.

M&L Washing rubbing down and stopping of distempered surfaces any type of wall incl preperation of old surface and then apply one coat of oil bound distemper of any tint over one coat of primer with 1mm wall care putty whereever required & specified by Engineer -in-Charge

M&L for applying one coat of acrylic emulsion exterior paint (Anti fungal paint-APEX or equivalent) over one coat of primer on old decorative surface of wall, ceiling cornices including preperation of surfaces by brooming scrapping down dust particle, smoke soot, moulds, moss and efforescent salts etc and making surface smooth by applying ready mix putty where required complete all as specified and as directed.

M&L for preperation of old plastered surfaces of ceiling and apply two coats of white wash complete all as specified and as directed.

Demolition of precast concrete block built in cement mortar complete all as specified and as directed .

M&L precast cement concrete type C-1, 1:3:6 (using 20mm graded aggregate) block masonary with solid blocks exc 10 cm in width and setting in cement mortar 1:6 complete all as specified and directed by Engr in Charge.

Demolition of cement concrete of any description in any position not otherwise specifically provided for

M&L for Plinth protection 75 mm thick cement concrete type B- 2, 1:3:6 using 40mm graded stone aggregate finishing cement concrete surface even and smooth without using extra cement complete all as specified and directed by Engr-in-chrage.

M&L 100mm thick Cement concrete C-2, 1:3;6(40mm graded aggregate) finished even & smooth without using extra cement

M&L TMT bars 10 mm cut to length bent to shape required including cranking and binding with MS wire n less than 0.9 mm dia but for stiffener of chainlink fencing complete all as specified and as directed.

M&L Cement concrete type B-0, 1:2:4 (12.5mm graded aggregate), 25mm thick on concrete surface over top of RCC chajjas with using waterproofing compund as per manufacture instruction finished even & fair with using extra cement Note: Waterproofing will not be measured seperately

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed.

M&L Screed bed or bedding layer of mortar 20 mm thick 1:4 for laying floor finishes complete all as specified and as directed.

M & L Rendering 10 mm thick cement plaster in cement mortar 1:4 on Vertical Surface complete all as specified and as directed.

M&L for Glazed ceramic coloured tiles in vertical surface 350 x250x 7 mm/ 450x 350x7 mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed.

M&L Non - skid Ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed.

Rounding to edges of stone slabs one edge, such as in steps , cooking platform, and other similar situations complete all as specified and as directed.

M&L Chequered cement concrete tiles 20cm x 20cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors with grey cement and pigments complete all as specified and as directed.

M & L Machine cut kota stone slab 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete

Mirror polishing on marble/ granite/ kota stone/ stone work where ever required to give high gloss finish and wex finishing complete all as specified and directed

M&L for 40mm thick cement concrete type B-1, 1:2:4 using 20mm graded stone aggregate finishing cement concrete surface even and smooth without using extra cement all as specified and as directed.

M&L for applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 kg per sq.m including cleaning surfaces all as specified and as directed.

M&L for broken stone or boulder hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface all as specified and as directed.

M&L for 100mm thick cement concrete type B- 2, 1:2:4 using 40mm graded stone aggregate finishing cement concrete surface even and smooth without using extra cement all as specified and as directed.

Taking down steel tubing and connections 15 mm bore complete all as specified and as directed.

Taking down steel tubing and connections 20 mm bore complete all as specified and as directed.

S & F of CPVC 20mm pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified.

S & F of CPVC 25mm pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified.

S&F bib taps, cast copper alloy with crutch or butterfly handle , screwed down , screwed for iron pipe or for brass ferrule & fixed . Size 15mm fixed in repair complete all as specified and as directed.

S & F 15 mm size stop valve copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipes or for union & fixed in repair

S & F pillar taps,15 mm bore fancy type cast copper alloy, with capstan heads, chromium plated, screwed down high pressure and fly nut screwed for iron pipes complete fixed in repairs

S&F in repairs stainless steel 12 inch size over head rain shower with 24 inch shower arm all as specified and directed

S&F Brass Chromium Plated Tubular towel rail, 20mm dia, D type, 60cm long between flanges in repair complete all as specified and as directed.

S&F SS soap dish approximate size 160 x 160 x 90 mm embedded in wall fixed in repair complete all as specified and as directed.

S&F in repair 2 in 1 Health Faucet with Hook (Chrome Plated) 1.5 Mtr Tube complete all as specified and as directed.

S&F 32mm Waste pipe 800mm long in repair complete all as specified and as directed.

S & F PVC Connection of size 15 mm ,600mm long with PTMT nuts complete all as specified

Taking down eaves gutters, sewage lines and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories)

S&F 50mm dia High density polyethylene pipes (HDPE) of pressure rating 6 kgf/cm2 fixed complete to walls, ceilings or in floors incl necessary fittings complete all as specified and as directed.

S&F 110 mm Ø PVC (SWR) pipe with single socketed in any length solvent cement jointed fixed to wall/column

S&F 75 mm Ø PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wallsb complete all as specified and as directed.

S& F PVC (SWR) bends any radius 75 mm bore with acess door complete all as specified and as directed.

S& F PVC (SWR) bends any radius 110 mm bore with acess door complete all as specified and as directed.

S&F PVC (SWR) junction single, (Single T) equal or unequal 110mm bore with acess door complete all as specified and as directed.

S&F PVC (SWR) junction single, (Single T) equal or unequal 75mm bore with acess door complete all as specified and as directed.

S&F PVC (SWR) vent cowl 75mm dia complete all as specified and as directed.

S&F PVC (SWR) vent cowl 110mm dia complete all as specified and as directed.

M&L for 75 mm PVC (SWR) floor trap, plain with grating including jointing with solvent cement fixed in repairs

Dismantling water tanks and removing to store exe 500 Ltr & n exe 1000 Ltr

S&F 1000 Litre Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I

S&F Ball valves 25mm bore dia high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipeand fixed in repairs . (Minimum weight 15mm-142gms/ 20 mm - 210 gms. /25mm- 455gms/ 40mm- 690 gms)

S&F 25 mm bore CPVC Ball value complete all as specified and as directed.

S&F 25 mm CPVC Tank Adaptor complete all as specified and as directed.

S & F Vitreous China wash down water closet pan (pedestal pattern), white (including seat cover, fixing bolt etc. and excluding flushing cistern and flush pipe ) fixed in repairs complete all as specified and as directed.

S & F vitreous China squatting pan, ‘Orissa’pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe and including provision of limeconcrete bedding ) in repair complete all as specified and as directed.

Supply 10 litres Capacity PVC valveless,syphonic action type,flushing cistern,low level,white with inlet,ball valve,float and handle including brackets & Flush pipe of polyethylene of low or high density or PVC. 32 mm dia, for low level cistern & fixing High or low level fluslhing cistern (exclusive of brackets), and connections to pipes and fixing of chain and pull, or lever, if any

S & F Wash basins, Vitreous China (flat back or angle back type) 550mmx400mm size, including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipefixed in repairs & Flush pipe of polyethylene of low or high density or PVC. 32 mm dia, for low level cistern

Supply of vitreous China urinal , full stall type ,white (excluding fluhing cistern, flush pipe and waste pipe ) & fixing of vitreous china urinals , bowl type (back or corner wall type) complete including providing and fixing plugs, bedding urinals against wall in cement mortar 1:2 securing urinals to plugs with and including 60 mm long brass screws, pointing around urinal back in cement , fixing automatic flushing cistern with brackets , flush pipe grating and union for discharge pipe (Exclusive of fixing supply pipe to flushing cistern trap and waste pipe)

Taking down chowkats or frames not exceeding 1.5 Sqm each but with shutters (without taking off shutters from the frames) all as specified.

Taking down chowkats or frames exceeding 1.5 Sqm but not exceeding 4.0 sqm each but with shutters (without taking off shutters from the frames) complete all as specified.

S&F 2nd class hard wood plain, solid straight chowkats and frames, wrought framed rebated on the solid rounded or chamfered put together with glue pinned at joints all as specified.

S&F 2nd class hard wood, 35 mm thick Glazed & skeleton shutters, open rebated & prepared to receive glass, gauze, etc. divided into squares with plain chamfered mitered and rebated sash bars any numbers, edges of framing plain, chamfered or rounded, fitted with cut & mitred beads for securing glass, etc., sizes of members of shutters as specified in SSR Part I, section 8, clause 8.24 (a); supplied & fitted to Chowkats all as specified.

S&F factory made 2nd class hard wood plain framed panelled shutter (Two panel) with lock rail and pannel of 9mm thicks BWP commercial ply or 12 mm veneered particle board with commercial vereered on both faces the size of rails and style as per IS 1003 (Part-I) kiln seasond and chemically pressure treated 40 mm thicks

Supply and fixing to existing door frames 30 mm thick Glass Fibre Reinforced Plastic (FRP) panelled door shutter of required colour and approved brand and manufacture, made with fire - retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate for forming hollow rails and styles, with wooden frame and suitable blocks of seasoned wood inside at required places for fixing of fittings, cast monolithically with 5 mm thick FRP laminate for panels conforming to IS: 14856, including fixing to frames, complete as specified by the manufacturer and as per directions of Engineer- in-charge.

Supply and fixing Fiber Glass Reinforced plastic (FRP)Door Frames of cross section 90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter of 30 mm thickness. The laminte shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady the frame., complete as specified by the manufacturer and as per directions of Engineer-in-charge.

S&F MS ordinary rat tail door springs (Capsule type) 300 mm long and including roller and roller plate complete all as specified

S&F extruded aluminium alloy handles, 125 mm long fabricated type anodised all as specified

S&F alluminium, anodised, barrel tower bolts of extruded section of size 150 mm long.

S&F 300 mm long, aluminium alloy, anodized, sliding door bolt with hasp, staple (bolt type) & fixing clips of sheet, cast or extruded section & fixing blots & sliding bolts of extruded section or cast aluminium alloy all as specified

S&F 100 mm long powder coated butt hinges, medium weight, cold rolled mild steel all as specified.

S&F 4 mm thick, sheet glass, ordinary quality and glazing with oil putty / beeding in squares not exceeding 0.5 sqm each pane all as specified .

S&F 4 mm thick, sheet glass, ordinary quality and glazing with oil putty / beeding in squares exceeding 0.5 sqm each pane all as specified .

S&F in repairs 4 mm thick figured glass , pin head type and glazing with oil putty in squares n exe 0.5 sqm in each pane complete all as specified & directed.

S&F aluminium alloy wire cloth 0.45 mm nominal dia of wire & average width of aperature 1.4 mm & fixed with aluminium wire staple.

M&L Preparing new wooden surfaces of any description exc. 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer all as specified

M&L for preperation old painted wooden surfaces of any description exc 10 cm width or girth and applying one coat of synthetic enamel paint all as specified and directed.

S&F in repairs 140mm Floor door stopper of aluminium alloy body and tongue, anodised with hard draw steel spring complete all as specified & directed..

S&F heavy duty stainless steel ceiling/ wall clothes stand for drying with UV protected nylon ropes and pulley 6 pipes x 6 feet full frame is of 4.5 kg all as specified and directed. Make : Easy dry, homWell, Skyware Luxury etc.

S&F Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and directed by Engr-in-chrage.

Cutting holes in brick walls, exc. half but not exc. one brick wall built in cement mortar for inserting hold fasts and making good dismantled portion in CM 1:3, or cement concrete 1:2:4 type B1 complete all as specified

S&F aluminum powder coated window/ventilator shutter including frame , any type (sliding or open-able ) with frame , & other similar work etc fabricated by using the JINDAL / CENTURY or equivalent standard section including necessary arrangement to receive 4mm thick sheet glass or wire mesh with aluminium channel beading, stainless steel screws, rollers, maruti lock & F frame including the cost of rubber gasket / rubber beading rollers, maruti lock & F frame etc complete . But the weight of the rubber gasket / beading rollers, maruti lock will not be measured with weight of aluminium shutter Note :- Sheet glass & wire mesh shall be measured & paid separately

S&F powder coated aluminium grill, 7.5 mm thick as per design code No. DG 007 of DURAL GRILL all as specified and as directed.

S & F Curtain rails anodised aluminium alloy with fixing brackets, stops, rollers etc. complete all as specified and as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed.

S&F hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters,nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts; posts adn struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets ( for securing wire mesh etc. including all necessary drilling and insulating of steel surface, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed.

M & L preparation of new steel surface and applying two coat of synthatic enamel paint incl one coat of red oxide primer complete all as specified and directed by Engineer-in-Charge.

Demolition of concrete(reinforced) of any description and in any position not otherwise specifically provided for and directed by Engineer-in-Charge.

M & L RCC (nominal mix ) in type B1 1:2:4(20mm graded aggregate) in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed by Engineer-in-Charge.

M&L for machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 grade

M&L Sand filling under floors or in foundations including watering and consolidation

Dismatling plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings.

Dismantling boarding, false ceiling any description, fixed in any position with nails/screws etc complete all as specified.

Taking down shutters of any description, exceeding 1.0 sqm but not exceeding 2 sqm each, from chowkhats, complete all as specified.

Taking down steel/CPVC tubing and connections 15 mm bore complete all as specified and as directed.

Taking down steel/CPVC tubing and connections 20 mm bore complete all as specified and as directed.

M&L precast cement concrete type C-1, 1:3:6 (using 20mm graded aggregate) block masonary with solid blocks exc 10 cm in width and setting in cement mortar 1:6 complete all as specified and directed by Engr in Charge.

M&L for preparation of newly plastered surfaces and applying two coats of oil emulsion distemper , white or tinted including a coat of alkali resistant priming paint before distemper over and icluding 1mm thick wall care putty on walls complete all as specified and as directed.

M&L for applying two coats of acrylic emulsion exterior paint (Anti fungal paint-APEX or equivalent) on old decorative surface of wall, ceiling cornices including preperation of surfaces by brooming scrapping down dust particle, smoke soot, moulds, moss and efforescent salts etc and making surface smooth by applying ready mix putty where required complete all as specified and as directed.

Washing rubbing down and stopping of distempered surfaces any type of wall incl preperation of old surface and then apply two coats of oil bound distemper of any tint with 1mm wall care putty where ever required & specified complete all as specified and as directed.

M&L for preperation of old painted surface of steel and applying one coat of synthetic enamel paint of any description not exc over 10 cm in width or girth complete all as specified and as directed.

M&L Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

M&L Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

S & F Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. of Fe 410W (Grade E- 250 ) Quality A, including for cutting to dead length where required, notching, drilling, fitting, riveting and/or welding or connecting with bolts and nuts (including rivets or bolts and nuts), providing and fitting angle cleats, fish plates, gusset plates etc., also for wedging, plumbing, truing up and fixing complete all as specified and directed by Engineer-in-Charge

S&F mild steel plates, plain or chequered, 5mm thick or over in thickness in available sizes complete all as specified and as directed.

S & F for 4 mm thick of size 600x600mm, pre-printed self embossed, textured designer E-board Classic to be fixed GI powder coated grid/section size 600mmx600mm with main runner 38x24x0.9mm thick ,cross tee 28.6x24x0.9 mm and wall angle 19x19xo.9 mm duly suspended with 4mm dia GI bar hangers 1200mm centre to centre both ways fixed with steel dash fasteners or from purlin from the roof with alignment clip including providing provisions for light fixtures of any size and finally applying two coats of oil bound distemper complete all as specified.

M & L for screed bed or bedding layer of mortar 20 mm thick in cement mortar 1:3 for laying floor finishes complete all as specified and as directed.

M&L vitrified ceramic tiles 10 mm thick (square/ rectangular) polished light shade, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match

M&L virified ceramic tiles 10 mm thick (square/ rectangular) polished light shade, area of each tiles not exceeding 0.36 sqm, on vertical surface etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match

M&L Non - skid Ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, supplying & fixing in opening as per specification & drawing

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification

Fixing only of any thickness wooden plain framed panelled shutter and glazed and skeleton shutter at same place after repairing complete all as specified and directed by Engr-in-chrage.

S&F 18/19 mm thick prelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination and other side balancing white lamination, fixed with screws in timber frame work in cup board shelves incl PVC edge band tape fixed complete all as specified and directed by Engineer-in-Charge.

M&L for Forming jambs, etc. to openings (to foregoing item), including cutting, toothing and properly bonding into old work, also facing, jointing and pointing to match existing work, complete in CM 1:6

S&F extruded aluminium alloy handles, 150 mm long fabricated type anodised complete all as specified and directed by Engr-in-chrage.

S&F Floor door stopper of 150mm lenth of cover plate of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed by Engr-in-chrage.

S & F powder coated aluminium shutters for window/ ventilators, without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised snap beading, screws, anodised aluminium fittings such as peg stays 150 mm long (1 No), hinges type B-21 100 mm long (2 Nos), suitable handle (1 No) complete all as specified and directed.

S&F Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer in-charge.

S&F Stainless steel sink, 1.00mm thick for kitchen or laboratory, with plug, waste pipe, washers, including cantilever cast iron brackets, connecting union etc. overall size 495mm x 420mm with bowl size 410mm x 330mm x 160mm fixed on cooking platform with proper slopping and covering with granite slab complete all as specified.

Supply only Integral waterproofing compound complete all as specified and as directed.

M&L for granite 20 mm (of any type) work (table rubbed and polished) in steps, jambs, pillars, win dow-cills, tread & riser of steps, cooking platform and like in cement mortar (1:4) including point ing in white cement (1:2) us ing marble dust with admix ture of pigment to match with shade of granite complete all as specified and as directed.

M&L for preparation of newly plastered surfaces preparatory to distempering, Priming plastered and other surfaces with alkali resistant priming paint, 1mm thick wall care putty & distempering walls with two coats of distemper oil emulsion, white or tinted complete all as specified and as directed.

M&L TMT bars 6 mm to 8 mm cut to length bent to shape required including cranking, bending spirally for hooping for columns, ceiling, hooking ends and binding with MS wire n less than 0.9 mm dia or securing with clips all as specified and directed

S&F PVC (SWR) branch piece, single (single Y) equal or unequal of dia 110mm with access door

S&F PVC (SWR) branch piece, double (double Y) equal or unequalof dia 110mm with access door

M & L for Cement concrete75mm thick cement concrete type C-2 ,1:3:6 (40mm graded aggregate ) as in plinth protection finished even and smooth without using extra cement

M&L for pre cast cement concrete (1:2:4) Type B1, using 20mm graded crushed stone aggregates in cover slabs, set in cement mortar 1:4 with plain faces, complete all as specified and directed by Engineer-in-Charge. Note: - Reinforcement steel shall be measured and paid separately under appropriate item of Schedule 'A'. .

Demolition of brick work or stone / boulder masonry built in cement mortar

Removing Dismantled/Demolished Building materials etc to a distance upto 5 kms beyond the lead including the rates, including loading,unloading and taking outside INS mandovi area.(Note:Contractor to identify area/location in civil area for disposal of debris.)

Taking down carefully copper / aluminium point wiring ( Light,fan socket or power) complete including fitting and fixture such as switches,ceiling roses, pendants,regulators, socket etc, removing material for taking credit and making good disturbed surface of walls, floors etc complete all as directed by Engineer-in-charge.

Taking down DB TPN/SPN, Main Switch,Sheet metal enclosure complete all as specified and as directed.

Taking down submain wiring complete all as specified and as directed.

Taking down old MCB complete all as specified and as directed.

Taking down old Switch Sockets complete all as specified and as directed.

Taking down Old Tube lights complete all as specified and as directed.

M & L for Point wiring controlled by one switch with cable 1.5 sqmm copper cable in multistranded unsheathed through concealed in wall with PVC conduit with all accessories including 1.5 sqmm cable conductor for earth wire including making connection with common earth earth dolly including pressed steel terminal boxes firmly concealed in wall with suitable modular frame and cover fixed with brass secrew for mounting switches sockets regulator ect all as per directed by engr-in-charge..

All as per item no 149 but for Ceiling/Exhaust Fan

All as per item no 149 but for one 3 pin socket outlet. 15 amps,independent, with cables 4 sq.mm size

All as per item no 149 but for switch socket combination 5 Amp on same board with other switches

All as per item no 149 but for switch socket combination 5 Amp on independent board

all per item no 149 herein before but 2.5 sq.mm pvc insulated and unsheathed copper conductor for switch socket combination 15 amps on independent board

Supply and fix in replacement modular switch one way 6 amp, 1 module 230V 50Hz AC supply.

Supply and fix in replacement modular switch one way 16 amp, 1 module 230V 50Hz AC supply.

S & F in replacement modular socket 3/5 pin 15 Amp, 230 Volt 2 module

S & F in replacement stepped type modular electronic fan regulator 230 volts 2 module minimum 120 watt all as directed by Engineer-in-charge

Supply & Fixing in replacement LED tube light fitting 1 X 20 watt baton integrated LED channel integral sleek extruded polycarbonate LED channel with white acrylic cover alonwith LED tube including flexible wire three core from existing ceiling rose to fitting duly mounted on PVC block with steel screw & sleeves all as directed by Engineer-in-charge.

Supply & Fixing in replacement LED tube light fitting 1 X 10 watt baton integrated LED channel integral sleek extruded polycarbonate LED channel with white acrylic cover alonwith LED tube including flexible wire three core from existing ceiling rose to fitting duly mounted on PVC block with steel screw & sleeves all as directed by Engineer-in-charge.

Supply and fixing LED building light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistan complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete.

S&f LED focus light fitting 1 X 7 watt baton integrated LED chanel integral sleek extruded polycarbonate LED channel with warm white light including flexible wire three core from existing ceiling rose to fitting duly mounted on PVC block for each bed. Make luker LSP07 or equivalent in/Bajaj/Philips complete all as specified and directed

Supply and fixing ceiling fans in replacement and depositing in MES yard complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE Energy efficient.

M & L for Taking down and Refixing of wall mounted fan complete including cleaning and painting with sythetic enamel paint as per existing / suitable colour all as directed by Engineer-in-charge.

S&F in replacement ceiling rose,surface bakelite 65X50 mm two to three terminals

S&F in replacement MCB 6-32 Amp 240 Volt single pole 'C' series including taking down old unsv MCB.

S&F in replacement MCB (DB) Vertical (TPN) 4 way double door 415 Volts complete including taking down existing old unserviceable DB.

Supply and fix in replacement MCB TP 415 Volts 63 Amps 'C' series incl taking down old unsv MCB.

Supply and fix in replacement MCB SPN 230 Volts 32 Amps 'C' series incl taking down old unsv MCB.

ML for submain wiring with 04 run of 10 sqmm single core copper cable PVC insulated unsheathed multistranded 1100 volt grade drawn through and inculding suitable size of rigid PVC conduit with accessories etc concealed in wall/ceiling with and including two run of 10 sqmm single core copper cable run through rigid PVC conduit concealed in wall from main DB to submain DB. NOTE :- Four run of 10 sqmm single core cable and 02 run of 10 sqmm single core cable as earthing contnuity conductor with PVC conduit concealed in wall shall be measured as one unit length. meter

M/L for earthing complete with galvanised steel earth plate electrode 60cm x 60cm x 6 mm thick burried directly on ground earth pit n. less than 2.25 m deep below the ground bend with top edge of the plate n. less than 1.5m below ground level connected to GI earth wire 4 mm by means of bolts,nuts,checks nuts and washers of galvanised steel including necessary earth work and excavation in any strata and PCC 1:3:6 type C2 chamber and chamber cover and light grade GI pipe 20 mm dia for protection of earth strip and GI wire etc complete all as per electrical plate No. 3 of SSR Part-I including connections with Earth testing point all as specified or indicated including testing on completion. NOTE: On testing after completion if the desired earth resistance is not obtained the earthing willbe redone at no extra cost.

Supply and fix modular switch one way 6 amp, 1 module 230V 50Hz AC supply.

Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300m sweep with, blades, and frame and louvers.

Supply and fix Switch socket outlet multi purpose 3 pin, 16 amp and one pin, 6 amp controlled by one switch.

SupplY & fixed Sheet Metal Enclosure DB, Single pole & neutral , Single Door , for housing MCBs

Wiring for circuit/submain wiring alongwith earth wire with the following sizes of FR is PVC insulated copper conductor, single core cable in surface/ recessed as required 2x2.5 sq. mm + 1x2.5 sq. mm earth wire earth wire

Supply and fixing amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of SP 6 To 32 AMP and current carrying capacity in the MCB DB complete with connection testing and commissioning.

Supply and fixing amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of SPN 32 AMP and current carrying capacity in the MCB DB complete with connection testing and commissioning.

S&F LED Mirror light with high output diffuser 2' long 10 watt 230 volts AC decorative type with driver holder and LED Lamp including connecting up with tree core flexible copper conductor cable of suitable size complete all as specified and directed

S&F in replacement MCB (DB) SPN 8 way double door 230 Volts complete including taking down existing old unserviceable DB.

Supply &fix in repairs exhaust fan made of sturdy engineering plastic complete with louvers shutters voltage 230v,50 hz RPM-1200 Copper winding of sweep 300mm including making holes if any and PCC works and testing all as directed by engr-in-charge

M&L for submain wiring with 02 run of 6 sqmm single core copper cable PVC insulated unsheathed multistranded 1100 volt grade drawn through and inculding suitable size of rigid PVC conduit with accessories etc concealed in wall/ceiling with and including one run of 6 sqmm single core copper cable run through rigid PVC conduit concealed in wall from main DB to submain DB. NOTE :- 02 run of 6 sqmm single core cable and 01 run of 6 sqmm single core cable as earthing contnuity conductor with PVC conduit concealed in wall shall be measured as one unit length. meter

M&L for submain wiring with 02 run of 4 sqmm single core copper cable PVC insulated unsheathed multistranded 1100 volt grade drawn through and inculding suitable size of rigid PVC conduit with accessories etc concealed in wall/ceiling with and including one run of 4 sqmm single core copper cable run through rigid PVC conduit concealed in wall from main DB to submain DB. NOTE :- 02 run of 4 sqmm single core cable and 01 run of 4 sqmm single core cable as earthing contnuity conductor with PVC conduit concealed in wall shall be measured as one unit length. meter

Supply &fix sheet metal enclouser single pole and neutral with two pin and earth plug and socket complete with one single pole 20 amps MCB 240 Volts

Supply and fix electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostat, NRV, connection piece etc. including testing and commissioning as directed by Engineer-in-charge.

S&F 20mm dia CPVC SDR 11 conduit pipe, including all standard fittings accessories complete all as specified and directed.

S&F bib taps cast copper alloy with crutch or butterfly handle screwed down screwed for 20mm dia CPVC pipe including suitable GI fittings of suitable length & dia complete all as specified & directed.

S&F stop valve for 20 mm dia CPVC pipe including connected GI fittings of suitable length & dia for connecting to geyser inlet & outlet pipes complete all as specified & directed.

Ramesh Enterprises (BID ID -3267264)

Super Construction (BID ID -3266042)