GE/PNH-62/2023-24

Amount

B&R PORTION:- Taking down cement plaster of any description on stone or brick walls etc including racking out joints, hacking for key scrubbing down with water etc. complete all as specified and directed.

Dismantling plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof covering complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floors and paving not exceeding 15cm thickness (below or above ground level), complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description complete all as specified and directed.

S&F 0.63mm thick galvanised corrugated mild steel sheeting with grade of Zinc coating of 275 gms/Sqm with two corrugation side lap and at least 150 mm end lap , fixed with L or J type or cranked hook bolts, in roof, walls etc, complete all as specified and directed.

All as per item No. 5 above, but except sheeting, complete all as specified and directed.

S&F 0.80mm thick plain galvanised mild steel sheeting with 275 gm/sqm Zinc coating as in ridge , hips, valley gutters, drip and straight flashingfixed with L or J type or cranked hook bolts, in roof etc., complete all as specified and directed.

M&L for pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

M&L for pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, valley gutter and similar works fixed with self tapping screws complete all as specified and directed.

M&L for machine pressed precast concrete interlocking paver block any shape and size confirming to IS-15658-2006 of 60mm thickness M-40 Grade,laid jointed pointed with grey cement and no pigments, complete all as specified and directed by Engr-in-Charge. Note: The sample shall be got approved by GE before bulk procurement & lot shall be got tested independently by the GE.

M&L for 100 mm thick PCC 1:4:8 type D-2 (using 40 mm graded crushed stone aggregate) as in sub base of flooring/ path/ hardstanding etc complete all as specified and directed.

M&L for 25 mm thick PCC 1:2:4 type B-0 (using 12.5 mm graded crushed stone aggregate) as in sub base, flooring etc complete all as specified and directed.

M&L for Non skid coloured ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exc 0.18Sqm but n exc. 0.38Sqm in floors/skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, laid over and including 15mm thick screed bed in CM (1:6), complete all as specified and directed.

M&L for chequered cement concrete tiles 300x300x 25mm thick, set & jointed in neat cement slurry in floors and pointed with grey cement mixed with pigments, laid over and including 15mm thick screed bed in CM 1:6, complete all as specified and directed.

M&L for rendering 15mm thick on fair faces of brick or concrete surfaces in cement mortar 1:4 with mixing of liquid water proofing admixture @ 200 ml/kg of cement and finished the surface even and smooth without using extra cement, complete all as specified and directed. Note: WPC shall be measured and paid separately

Supply only liquid water proofing admixture complete all as specified and directed.

M&L for rendering 10 mm thick on fair faces of brick or concrete surfaces in cement mortar 1:6 and finished the surface even and smooth without using extra cement, complete all as specified and directed.

M&L for 5 mm thick rendering in CM 1:3 on fair faces of brick or concrete surfaces of ceiling & finishing the surface even and smooth without using extra cement, complete all as specified and directed.

M&L for rendering 15 mm thick on fair faces of brick or concrete surfaces in cement mortar 1:4 and finished the surface even and smooth without using extra cement, complete all as specified and directed.

M&L for rendering 20 mm thick on other than fair faces of brick or stone masonry wall surfaces in cement mortar 1:6 and finished the surface even and smooth without using extra cement, complete all as specified and directed.

M&L for rendering 15 mm thick on other than fair faces of brick or stone masonry wall surfaces in cement mortar 1:4 and finished the surface even and smooth without using extra cement, complete all as specified and directed.

M&L for applying two coats of white wash including preparation of newly plastered surfaces of wall complete all as specified and directed.

M&L for rendering 15 mm thick on other than fair faces of brick or stone masonry wall surfaces in cement mortar 1:6 and finished the surface even and smooth without using extra cement, complete all as specified and directed.

M&L for preparation of newly plastered / unplastered surfaces of wall including cornices pilaster etc, and applying two coats of cement base paint over a coat of white was complete all as specified and directed.

M&L for preparation of newly plastered / unplastered surfaces of wall including cornices pilaster etc, and applying two coats of OBD over & incl a coat of 1 mm thick wall care putty complete all as specified and directed.

Taking down shutters of any description exceeding 1sqm and not exceeding 2sqm each, complete all as specified and directed.

Taking down shutters of any description not exceeding 1sqm each, complete all as specified and directed.

Taking down chowkats with shutters (without taking off shutters from the frame) not exc 1.5 Sqm each complete all as specified and directed.

Taking down chowkhat or frame exc 1.5 Sqm but n exc 4 Sqm each with shutters (without taking of shutter from the frames) complete all as specified and directed.

S&F pressed steel frame of size 105X60mm for doors as per IS 4351 using PBI Sheet of 1.25 mm thick with double rebated including mild steel hinges medium weight 100mm long and 25X3mm flat iron in holdfast. tie bar including necessary fixing lugs, lock strike plate and fixing arrangement etc. complete all as specified and directed.

S&F pressed steel frame of size 125X60mm for doors as per IS 4351 using PBI Sheet of 1.25 mm thick with double rebated including mild steel hinges medium weight 100mm long and 25X3mm flat iron in holdfast. tie bar including necessary fixing lugs, lock strike plate and fixing arrangement etc. complete all as specified and directed.

M&L for 35mm thick 2nd class hardwood plain, framed, panelled shutter (any number of panels) with panels of timber flat on both sides (feather edged) or of veneered paticle board medium density, wood patilcle board with commercial face veneers complete all as specified and directed.

M&L for 35 mm thick 2nd class hardwood glazed and skeleton shutters, open rebated and prepared to receive glass, gauge etc, (with sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc sizes of members of shutters as specified in SSR part-I, section 8, clause 8.24 (a) complete all as specified and directed.

S&F Aluminium anodised, barrel tower bolts of extruded section of size 150mm and fixed, complete all as specified and directed.

S&F Aluminium alloy handles, cast type, anodised of size 150mm and fixed, complete all as specified and directed.

S&F 300mm long aluminium alloy anodized sliding door with haps, staple (bolt type) and fixing clips of sheets, cast or extrusted sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden / steel frames or stone/ concrete, glazed with putty or fixed with beads, complete all as specified and directed.

S&F Solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, fixing in opening as per specification & drawing complete all as specified and directed.

S&F factory made solid core PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC sheet, 'C' channel having PVC sheet strip of 20mm width stuck inside with solvent cement for styles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap inserted for top rail and bottom rail; panelling of plain colour PVC sheet to be fitted in MS frame welded/ sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement complete all as specified & shown in relevant drawing of item No. 08080 in MES Schedule (Part-II) complete all as specified and directed by Engineer-in-Charge.

S&F galvanised mild steel wire cloth 0.56 nominal dia of wire and average width of aparture 1.18 mm and fixed with tinned tacks or galvanised wire staples, complete all as specified and directed.

S&F mild steel butt hinges, medium weight, cold rolled,100mm long, complete all as specified and directed.

S&F Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed.

S&F Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete without glazing bars, dovetailed or welded complete all as specified and directed.

S&F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples or wooden beading, complete all as specified and directed.

S&F Sheet glass, ordinary quality, 4mm thick and glazed with oil putty or wooden beads, in square n exc. 0.5 Sq m each pane, complete all as specified and directed.

S&F figured glass, pin headed type, 3mm thick and glazed with oil putty or wooden beads, in square n exc. 0.5 Sq m each pane, complete all as specified and directed.

S&F 300mm Mild steel ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed.

M&L for preparation of new wooden surfaces of any description, not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint of Ist quality over a coat of pink primer, complete all as specified and directed.

M&L for applying two coats of synthetic enamel paint of Ist quality over a coat of red oxide primer to new or previously untreated steel surfaces over 10cm width or girth including preparation of surfaces, complete all as specified and as directed.

M&L for Plain cement Concrete 1:3:6 type-C1 (using 20mm graded crushed stone aggregate) as in copings, hold fasts plinth band, bed blocks and like slightly rounded or chamfered angles as directed including necessary form work, complete all as specified and directed.

M&L for preparation of old plastered or unplastered surfaces of wall and applying one coat of oil bound distemper of any tint on wall, complete all as specified and directed.

M&L for complete removal of existing treatement from wall plaster and applying two coats of oil bound distemper white or any tint, incl one coat of 3mm thick wall care putty complete all as specified and directed.

M&L for preparation of old plastered/ un-plastered wall surfaces or wood surfaces including brooming down or steel wire brushing, scraping down, smoke soot, mould, moss, efflorescent salts, trading oil and greasy spots, and applying one coat of cement base paint on wall and asbestos cement sheets, complete all as specified and directed.

M&L for 50mm thick PCC 1:3:6 Type C-1 (using 20mm graded crushed stone aggregates) laid in alternate bays (not exceeding 2 sqm each) as in plinth protection, finished the surfaces even & fair, including filled the joints with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight complete all as specified and directed.

S&F in repair Bib tap 15 mm bore with flange, Brass CP, fancy type. with crutch or butterfly handle screwed down screwed for iron pipe or for brass ferrule complete all as specified and directed. Make:- Jaquar cat part No CON-047KN or equivalent cat part of make as specified in P.S.

S&F in repair Angular stop valves cast copper alloy 15 mm dia, fancy type, chromium plated with wall flange screwed down, high pressure, with capstan handle screwed both ends for iron pipes or for unions complete all as specified and directed. Make-Jaquar Cat Part No:-CON-059KN or Equaivalent cat part of make as specified in P.S.

S&F in repair Vitreous china squatting pan (Orissa pattern) size 580 x 440 mm, snow white, with 'P' or 's' trap, front or back inlet and integral foot rests, complete connection to drain (outgoing pipe) and to flushing pipe and syphonage pipe etc. including lime concrete bedding, complete all as specified and directed.

S&F in repair PVC valve less syphonic action type flushing cistern 10ltr capacity , low level white with inlet ball valve float and handle including brackets including 32mm dia PVC. flush pipe for low level cistern including all joints complete all as specified and directed. Make:- Prayag cat part No 501 or equivalent cat part of make as specified in P.S..

S&F in repair PVC connection 15mm size with PTMT nuts on both ends of length 450mm complete all as specified and directed.

S&F in repair PVC connection 15mm size with PTMT nuts on both ends of length 600mm complete all as specified and directed.

S&F in repair flush pipe/waste pipe of polyethylene of low or high density of PVC, 32mm dia complete all as specified and directed.

S&F in repair PVC (SWR) pipes 110mm dia any length single socketed with rubber ring joint laid in trenches/floors as soil pipe(vent pipe, complete all as specified and directed.

S&F in repair telephonic Health faucet (ABS Body) with 1.5 metre long easy Flex tube in chrome finish and wall Hook, to fix in 15 mm dia iron pipe or brass ferrule complete all as specified and directed.

S&F in repair CP jet spray with holder for EWC, 1.5 mtr long flexible pipe incl necessary nut bolt and washers complete all as specified andd directed.

S&F in repair Plastic water closet seat cover, white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specified and directed.

Cleaning/Disinfecting of PVC/cemented water storage tank any capacity of any capacity with disinfecting chemicals (chlorine) properly with water thoroughly flush out complete all as specified and directed.

Cleaning/clearing and maintenance of sewage lines any bore, manholes including CI stacks gully traps under ground lines any depth by removing any type of blockage from drain 100/150mm dia by roding from manholes to manholes and flushing after cleaning including manholes sludge/sludge water to be disposed off outside the periphery of defence land including taking off manhole covers and refixing the same after cleaning sewage lines, sewage lines cleared/cleaned under this item are to be maintained and kept fully functional by removing any type of blockage. The cost of this operation/provision shall be deemed to be included in unit rate quoted by the contractor complete all as specified and directed. Note :- Unit rate quoted by tenderer shall include taking out sludge from line and manholes(liquid/semi liquid/solid) excavtion of borrow pits for dumping sludge, removing including loading/unloading and transportation etc

Opening of cover(of any description and size) of septic tanks and soakage wells/pits, desludging/dewatering of septic tanks and soakage wells/pits of any size and depth by mechanical pumping (truct mounted(Mechanically)/Manually making it functional to the entire satisfaction of Engr-in -Charge and removing sludge outside the periphery of defence land at bis own arrangement where sanitary hazards do not take place as per directions/instructions of civil authority and burried in excavated pits and covering the same including refixing covers after cleaning complete all as specified and directed. Note:- Unit rate quoted by tenderer shall include taking out sludge from line and manholes(liquid/semi liquid/solid) excavtion of borrow pits for dumping sludge, removing including loading/unloading and transportation etc

Cleaning of blocked WC seats upto first manhole and making the drain pipe of any dia fully functional by flusing with water to entire satisfaction of Engg-in-charge including disposal of sludge etc away from preiphery of defence land at his own arrangement where sanitary hazards do not take place as per direction/ instruction of civil authority and burring in borrow pits (excavation and earth work shall be deemed to be included in the unit rate) complete all as specified and directed.

M&L for preparation of old plastered or unplastered surfaces of ceiling and applying one coat of white wash on ceiling, complete all as specified and directed.

Demolition of brick or stone masonry, built in cement mortar including all quoins, arches, pillars etc but excluding ashlars facings, dressed stone work, complete all as specified and directed.

M&L for brick work with sub class ‘B’ bricks straight or curved on plan exc 6m mean radius, built in cement mortar (1:6), complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L for non skid ceramic coloured tiles 7 to 8 mm thick (square/Rectagular) area of each tile exceeding 0.11 Sqm but not exc 0.18 Sqm in floor etc, set & jointed in neat cement slurry and pointed in white or coloured cement to match the surface over and including cement screed bed 15 mm thick in cement mortar 1:6 base complete all as specified and directed.

M&L for Glazed ceramic coloured tiles of size 450mm x350mm x7mm/ 350mm x250mm x 7mm thick, as in vertical surfaces such as in skirting and dado etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles over and including 10mm thick back coat layer in cement mortar 1:4, complete all as specified and directed by Engr-In-Charge.

M&L for walling of random rubble stone/boulder masonry brought upto course, well bonded, bedded and solidly hearted, built in cement mortar (1:6), complete all as specified and directed.

M&L for walling of random rubble stone/boulder masonry brought upto course, well bonded, bedded and solidly hearted, built in cement mortar (1:6), except stone complete all as specified and directed.

Taking up or down steel tubing of 20 mm bore pipe and connection laid in trenches or floors or fixed to walls and including cleaning for refixing or removal to store with all fittings, complete all as specified and directed.

Refixing old steel water tubing of 20 mm bore and connections in new or old position fixed to walls, ceilings and floors etc. including fittings as requiered, complete all as specified.

S&F GI tubing of 20 mm bore ‘medium grade’ galvanized with all fittings like socket, union, elbow, bend, tees etc fixed to walls and ceilings or laid in floors, complete all as specified and directed.

Taking up or down steel tubing of 15 mm bore pipe and connection laid in trenches or floors or fixed to walls and including cleaning for refixing or removal to store with all fittings, complete all as specified and directed.

Refixing old steel water tubing of 15 mm bore and connections in new or old position fixed to walls, ceilings and floors etc. including fittings as requiered, complete all as specified.

S&F GI tubing of 15 mm bore ‘medium grade’ galvanized with all fittings like socket, union, elbow, bend, tees etc fixed to walls and ceilings or laid in floors, complete all as specified and directed.

S&F in repair 15mm bore gun metal globe or gate valve (ISI marked) with iron wheel head,screwed both ends for iron pipe complete all as specified and directed.

S&F in repair 20mm bore gun metal globe or gate valve (ISI marked) with iron wheel head,screwed both ends for iron pipe complete all as specified and directed.

S&F in repair 15mm bore pillar tap cast copper alloy with capstan head, fancy type, chromium plated, screwed down, high pressure, with or without lettered 'Hot or Cold' with long screwed for iron pipe complete all as specified and directed. Make:- Jaquar cat part NoCON-011KN or equivalent cat part of make as specified in P.S.

S&F in repair Concealed stop valves/cock cast copper alloy 15 mm dia, chromium plated with wall flange screwed down, high pressure, with butterfly handle screwed both ends for iron pipes or for unions complete all as specified and directed.

S&F in repair vitreous china wash hand basin, white, flat back, size 550x400 mm excluding taps, waste, chain & plug and porcelain stopper but exclusive of fixing of supply and waste pipe including cutting for and pinning in ends of brackets or erecting stand etc complete all as specified and directed.

S&F in repair vitreous china urinals, bowl type of size 465x355x265mm white (minimum) with grating and union for discharge pipe (excluding flushing cistern and waste pipe),complete including poviding and fixing plugs, bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement, fixing with automatic flushing cistern with brackets, flush pipe, waste pipe grating and union for discharge pipe complete all as specified and directed.

S&F in repair vitreous china urinals, bowl type of size 465x355x265mm white (minimum) with grating and union for discharge pipe (excluding flushing cistern and waste pipe),complete including poviding and fixing plugs, bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement, fixing with automatic flushing cistern with brackets, flush pipe, waste pipe grating and union for discharge pipe complete all as specified and directed.

S&F in repair 20mm bore ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Minimum weight - 210 gms) complete all as specified and directed.

S&F in repair PVC (SWR) bends of any radius 110mm dia provided with access door, complete all as specified and directed.

S&F in repair PVC (SWR) bends of any radius 75mm dia provided with access door, complete all as specified and directed.

S&F in repair PVC (SWR) branch piece, single (single Y) equal or unequal 110mm dia, complete all as specified and directed.

S&F in repair 75 mm dia PVC floor trap with grating including jointing with solvent cement to waste pipe complete all as specified and directed.

S&F in repair PVC soil waste and vent pipe 75 mm dia any length single socketed with rubber ring joint, laid in floor/walls as soil pipe including clamps, complete all as specified and directed.

Demolition or breaking up drain pipe of any size (salt glazed stone ware, AC, PVC or reinforcement concrete) set in cement mortar/concrete complete all as specified and directed.

S&F 150 mm bore salt glazed stone ware drain pipes, grade ‘A’ laid in trenches and jointed in CM 1:3, complete all as specified and directed by Engr-in-Charge.

M&L for concrete bed to drain pipes including packing under and haunching against the sides of pipes for 150mm SGSW pipe after they are laid in PCC (1:4:8) type D-2 (using 40mm graded crushed stone aggregate) & tested, complete all as specified and directed.

Demolition of cement concrete (reinforced) of any description and in any position (reinforement cut as required to facilitate demolition), complete all as specified and directed by Engineer-in-Charge.

M&L for precast cement concrete 1:2:4 type B1 (20mm graded crushed stone aggregate) as in landings, cover slab for man holes, chullah hoods, chajjas, water troughs, mangers, shelves etc set in cement mortar(1:6) including necessary formwork, complete all as specified and directed.

M&L for reinforced cement concret (nominal mix) type B-1, 1:2:4 (20mm graded aggregate) as in columns, pillars, piers, posts and struts and the like complete all as specified and directed.

Formwork to sides of pillars, posts, struts, piers, columns and stanchions in square or rectangular or polygonal with rough finished surface etc, complete all as specified and as directed.

S&F mild steel TMT bars 10 mm dia and over, cut to length, bent to shape requred, including cranking , bending spirally for columns hooking for columns hooking ends and binding with and including mild steel wire (annealed ) not less than 0.9mm dia or securing with clips complete all as specified and directed.

S&F rolled mild steel sections as in main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors, fixed with angle cleats or other connected plate confirming to Fe 410W(Gde E-250), quality 'A' complete all as specified and directed.

S&F in repair Vitreous china wash down water closet pan (pedestal pattern), white (excluding, flushing cistern and flush pipe) with & including seat cover and fixing bolts, connection to drain (or outgoing pipe) and antisyphonage pipe and including packing with white cement etc complete all as specified and directed.

S&F in repair brass chromium plated shower rose 125mm size with or without swivel joints, any size, including fixing to steel pipe or union complete all as specified and directed.

S&F in repair Gratings, 125 mm dia with waste hole of PTMT complete all as specified and directed.

S&F Rotational moulded polyethylene water storage tanks triple layer (Cylindrical vertical with closed top) hoisted and fixed in position all as spd in SSR Pt-I, of capacity 500 Ltrs incl with 15mm Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule including dismantling existing tank and removal from site complete all as specified and directed.

S&F Rotational moulded polyethylene water storage tanks triple layer (Cylindrical vertical with closed top) hoisted and fixed in position all as spd in SSR Pt-I, of capacity 1000 Ltrs incl with 20mm Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule including dismantling existing tank and removal from site complete all as specified and directed.

Petty repairs for leaking water in bib tap, pillar tap, stop cock, angle valve of any description any size by changing the washer/jumper etc complete all as specified and directed by Engr-in-Charge.

Removal of air lock/blockage of water in GI tubing 15/20mm bore incl taking down (if reqd), cleaning the pipe or fittings etc and refixing the same in position complete all as specified and directed by Engr-in-Charge.

M&L for preparation of old plastered or unplastered surfaces of wall and applying one coat white wash, complete all as specified and directed.

E&M PORTION:- Taking down carefully copper/ aluminium unserviceable/ perished point wiring (light, fan, socket or power complete including fixture and fittings such as switches, ceiling roses, pandents, regulators, sockets, light fittings,removing material from site for taking credit etc and making good disturbed surfaces of wall, floors, complete all as specifiecd and directed.

M&L for point wiring with two single core 1.5 Sqmm (nominal cross section area) FRLS PVC insulated unsheathed multistranded copper conductor cable and one single core 1.5 Sqmm (nominal cross section area) FRLS PVC insulated unsheathed multistranded copper conductor cable as earth continuity to common earth and connecting to earth dolly running in and including PVC casing & caping (ISI marked) of suitable size with PVC boards of appropriate sizes and all requisite accessories such as PVC elbow, Tee, collars, bends etc. with PVC terminals box & cover for mounting swtches, sockets, fan regulator etc for mounting switches, sockets, fan regulators etc complete all as specified and as directed for the following :-

One light/fan point controlled by one way switch 6 Amp complete all as specified and directed.

One ligh point controlled by two, two way switch 6 Amp complete all as specified and directed.

One 3/5 pin socket outlet 6 amp on same board complete all as specified and directed.

One 3/5 pin socket outlet 6 amp independent board complete all as specified and directed.

One bell point controlled by one way switch 6 Amp complete all as specified and directed.

All as per srl item No 116 here in before but for one 3 pin socket outlet 16/20 Amp independent with two single core 2.5 Sqmm size cable as phase & neutral and one single core 2.5 Sqmm as in continuous earth wire complete all as specified and directed.

S&F in repair ceiling rose, 3 terminal, surface bakelite 65 mm x 50mm, PVC/poly carbonate, insulated body, complete all as specified and directed.

S&F in repair switch piano flush type 6 Amp single pole one way, (ISI marked), complete all as specified and directed.

S&F in repair switch piano flush type 6 Amp, two way, (ISI marked), complete all as specified and directed.

S&F in repair switch piano bell push flush type 5 Amp single pole one way (ISI marked) complete all as specified and directed.

S&F in repair socket outlet 2 in 1, 3 pin, 5 Amp flush type universal, complete all as specified and directed.

S&F in repair Switch socket multipurpose combination 2 in 1, 5 pin, 6 Amp flush type universal, complete all as specified and directed.

S&F in repair Switch socket outlet multipurpose combination 2 in 1, 6 pin, 5 and 15 Amp flush type universal, complete all as specified and directed.

S&F in repair Lamp holder PVC/Polycarbonate type with back plate suitable for batten fittings, complete all as specified and directed.

S&F in repair stepped type electronic fan regulator flush type on the existing phenolic laminated sheet etc. for 1200 / 1400mm sweep, complete all as specified and directed.

S&F in repair electric bell ding dong type 230 volts AC supply 50 Hz complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repair inverter LED batten 1x 20W, with square profile and polycarbonate channel, lithium iron battery with charging time of 8 to 10 hours and backup tile upto 04 hours with driver, holder incl LED tube light connecting up with with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed. Make : Havells cat part No. LHEXACP7FN1W020 or equivalent make as specified in PS

Supply and fixing in repair LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

S & F in repair LED light fitting 1x9W/1X10W bulk head luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

S & F in repair wall mounted decorative LED light fittings 15 watt connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

S&F in repair surface mounted square LED panel of size 192mm x 192 mm x 23mm, aluminium die cast body with premium diffuser to ensure glare free & even distribution of light , of 18 watt capacity , lumen output 6000K, with pre-wired fitting complete all as specified and directed. Make : Havells cat part No. LHEAAWP7IL1WO18 or equivalent make as mentioned in PS

Supply and fixing in repair LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and directed.

S&F in repair gate light fittings, outdoor type, high power , 25 watt, IP65 luminaire, prewired with suitable pole for mounting complete all as specified and directed. Make: Havells cat part No. Coral Opal IP65 or equivalent make as mentioned in PS

Supply and fixing in repair LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and directed.

S&F in repair LED bulb 9-12 watt inverter type with 2 hour backup, complete all as specified and directed.

S&F in repair LED lamp CDL 10 watt with holder base (B22) type, complete all as specified and directed. Make of LED lamp:- Havells cat part No LHLDEUEEML8R010 or Equivalent cat part of make as specified in P.S.

S&F in repair LED driver suitable for 35 watt LED ceiiling light fittings and making connection to fitting complete all as specified and directed. Make:-Havells cat part No-LEDDRIVER36V36WS or Equivalent cat part of make as specified in P.S.

S&F in repair single pole and neutral enclosure with a two pin and metal earth plug and socket complete with & incl one single pole MCB of 20 Amps complete all as specified and directed.

S&F in repair sheet metal enclosure for DBs, vertical TPN double door (IP43), 4 ways built in bus bars suitable for 415 volts, AC, 50 Hz and suitable for FP MCCB as incommer and out going SP/TP MCBs complete all as specified and directed. Note:- MCBs shall be measured and paid separately.

S&F in repair sheet metal enclosure for DBs, SPN double door (IP43), 4 ways built in bus bars suitable for 240 volts, AC, 50 Hz , including connecting both incoming and outgoing cable termination with proper taping, lagging testing and commissioning complete all as specified and directed.

S&F in repair sheet metal enclosure for DBs, SPN double door (IP43), 8 ways with 200 amps rated bus bar suitable for 240 volts, AC, 50 Hz, including connecting both incoming and outgoing cable termination with proper taping, lagging testing and commissioning complete all as specified and directed.

S&F in repair sheet metal enclosure for DBs, SPN double door (IP43), 12 ways with 200 amps rated bus bar suitable for 240 volts, AC, 50 Hz, including connecting both incoming and outgoing cable termination with proper taping, lagging testing and commissioning complete all as specified and directed.

S&F in repair MCB TPN 40-63 amps 415 volts 10 KA 'C' series, complete all as specified and directed. Make:-Havells cat part No- DHMGCTNF040 - DHMGCTNF063 or Equivalent cat part of make as specified in P.S.

S&F in repair MCB SPN 40-63 amps 415 volts 10 KA 'C' series, complete all as specified and directed. Make:-Havells cat part No- DHMGCSNF040 - DHMGCSNF063 or Equivalent cat part of make as specified in P.S.

S&F in repair MCB single pole 6 to 32 amps 240 volts 10 KA 'C' series complete all as specified and directed. Make:-Havells cat part No-DHMGCSPF006-032 or Equivalent cat part of make as specified in P.S.

S&F heavy duty metallic exhaust fan 380/200 mm sweep 1400 RPM, single phase 240 Volts including all connecting accessories, complete and taking out old existing exhaust fan, complete all as specified and directed.

S&F in repair of PVC counduit non matalic rigid, of size 25 mm dia (external) incl all accessories use for fixing of conduit on wall and ceiling etc, complete all as specified and directed.

Supply and fixing in repair LED bush & spike light luminaire of capacity 9 watt, IP65 protection, 240 volt complete all as specified and directed.

S&F in repair PVC casing caping of size 25 mm incl all fixing accessories complete all as specified and directed.

S&F Earthing complete with galvanized steel earth plate electrode 60cmx 60cmx6mm thick buried directly in ground (earth pit not less than 2.25m deep below normal ground level) with top edge of the plate not less than 1.5m below normal ground level, connected to galvanized iron wire 4.0mm dia by means of bolts, nuts and washers of galvanized iron or steel, protected by GI light grade pipe 15mm bore including GI light grade water pipe 20mm dia with funnel all as shown in electric plate No. 3 of 2009 SSR Pt-I and testing complete including earth work in any type of soil, PCC 1:2:4 type B-1 as in earthing pit and cover 50mm thick reinforced with 6mm dia MS round bar @ 10cm C/C both way and MS frame, common salt, charcoal and testing on completion including dismantling unsv earthing, complete all as specified and directed.

S&F in repair Sub main wiring with single core cable 2x 4 Sqmm FRLS insulated unsheathed stranded copper conductor cable 1100 Volts grade including surface PVC casing caping medium grade alongwith 1x 4 Sqmm FRLS insulated unsheathed copper conductor cable as earth wire connected with main earth dolly, complete all as specified and directed. Note:-Three wire of 4 sqmm and one run of PVC conduit/casing caping shall be measured as one unit.

S&F in repair Sub main wiring with single core cable 2x 6 Sqmm FRLS insulated unsheathed stranded copper conductor cable 1100 Volts grade including surface PVC casing caping medium grade alongwith 1x 6 Sqmm FRLS insulated unsheathed copper conductor cable as earth wire connected with main earth dolly, complete all as specified and directed. Note:-Three wire of 6 Sqmm and one run of pvc conduit/casing caping shall be measured as one unit.

S&F 1100 volts grade heavy duty cable PVC insulated solid aluminium conductor served with PVC tape and over all PVC sheathed in service connections suspended by insulating hangers not more than 1 m apart including 4mm dia GI suspension wire, one twin core cable flat or circular of size 6 Sqmm 2 core & including taking down old old unsv service cable connection, complete all as specified and directed.

S&F 1100 volts grade heavy duty cable PVC insulated solid aluminium conductor served with PVC tape and over all PVC sheathed in service connections suspended by insulating hangers not more than 1 m apart including 4mm dia GI suspension wire, one twin core cable flat of circular of size 10 Sqmm 2 core including taking down existing old service connection, complete all as specified and directed.

Repair and maintenance of unserviceable ceiling fan of 1200mm/1400mm sweep at contractor's work shop, incl dismantling complete the ceiling fan parts, inspecting serviceability of all the parts, refixing of serviceable parts after cleaning and replacement of unserviceable parts with company's genuine parts i.e. capacitor, bearing, bushes, shaft, bracket, rubber bush, connecting wire, PVC connector, aluminium clamp for rod, bracket, bush rod, greasing/oiling etc assembling, cleaning and testing of ceiling fan complete all as specified and directed. Note: (i) Unserviceable parts as above shall be measured and paid separately under relevant items No 157 to 165 of Sch 'A' as supply only. (ii) Rewinding of stator will be measured & paid for separately under relevant item of Sch 'A'. (iii) Cost of minor part i.e. Cotter pin, screws shall be deemed to included in the cost of quoted rate.

Supply only bearing good quality for ceiling fan 1200mm/1400mm sweep ISI marked complete all as specified and directed.

Supply only Gun metal bush for ceiling fan 1200mm/1400mm sweep complete all as specified and directed.

Supply only capacitor 2.5 mfd ISI marked complete all as specified and directed.

Supply only brass bracket assy for hanging the ceiling fan 1200mm/1400mm sweep complete all as specified and directed.

Supply only 3 core flexible wire 40/.0076, white colour from ceiling rose to fan connector complete all as specified and directed.

Supply only stator shaft for ceiling fan complete all as specified and directed.

Supply only fan blade for ceiling fan 1200 mm sweep of existing make complete all as specified and directed.

Supply only fan blade for ceiling fan 1400 mm sweep of existing make complete all as specified and directed.

Supply only canopy (top/bottom) of ceiling fans any make /size of colour matching with existing canopy/ fan colour complete all as specified and directed.

M&L for removing of old burnt winding of any size , type and rewinding of stator winding with superior quality copper wire with insulation complete all as specified and directed.

M&L for painting of ceiling fans complete, in situ with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etc complete all as specified and directed.

M&L for Replacement of down rod of ceiling fan with down rod of 15mm bore medium grade GI pipe 0.45 metre long with clamps, bolts, nuts, split pins washers of suitable size of approved quality complete all as specified and directed by Engineer in charge.

All as per item No 168 above but of length 0.60 Mtr complete all as specified and directed.

Repair and maintenance of unserviceable exhaust fan of any cap and sweep by dismantling the exhaust fan parts, inspecting the serviceability of parts, refixing of serviceable parts after cleaning, replacement of unerviceable parts i.e. beaing, bush, capacitor, connecting wires, fan blade, locknut, rubber pad etc, oiling/greasing, cleaning and testing of exhaust fan complete all as specified and directed. Note: (i) Unserviceable parts replaced shall be measured and paid separately under relevant items No 171 to 173 of Sch 'A' as supply only. (ii) Rewinding of stator winding shall be measured & paid for separately under relevant item of Sch 'A'. (iii) Cost of minor part i.e. screws shall be deemed to included in the cost of quoted rate.

Supply only double ball bearing (ISI marked) for exhaust fan of 200 mm sweep to 450 mm sweep fan complete all as specified and directed.

Supply only gun metal bush for Exhaust fan of any capacity. complete all as specified and directed.

Supply only blade of exhuast fan of 200 mm sweep to 450 mm sweep as per existing make complete all as specified and directed.

M&L for rewinding of 300mm sweep exhaust fan motor with superior quality copper winding wire with insulation complete all as specified and directed.

M&L for rewinding of 450mm sweep exhaust fan motor with superior quality copper winding wire with insulation complete all as specified and directed.

M&L for preparation of painted surfaces of exhaust fan of any make and size by scrubbing old and applying one coat of synthetic enamel paint by spray painting complete all as specified and directed by Engr-in-Charge.

Taking out old u/s ceiling fan from site of capacity 1200/1400 mm sweep and replacement of ceiling fan with new of existing make and capacity incl all connecting accessories complete all as specified and directed.

Disconnecting electric & water connection to geyser of capacity 25/35/50 litr, taking down from existing position, dismantling and inspecting all the parts for its serviciability, cleaning of serviceable parts i.e. heating element, base assembly, connecting lead, thermostat, electric contact, electric wiring, indicators, safety valves etc re-fixing in the same in position, testing complete all as specified and directed by Engr-in-Charge. Notes: (i) The defective parts to be replaced shall be measured and paid separately under relevant item No 179 to 190 of Sch 'A' as supply only (ii) Cost of minor items i.e. screws, nuts, bolts etc shall be deemed to be included in this item

Supply only heating element of capacity 2 KW, ISI marked with rubber gasket suitable for existing size, type & make of geyser complete all as specified and as directed.

Supply only heating element of capacity 1.5 KW, ISI marked with rubber gasket suitable for existing size, type & make of geyser complete all as specified and as directed.

Supply only thermostat, ISI marked suitable for existing size, type & make of geyser complete all as specified and as directed.

Supply only indicator lamp suitable for existing size, type & make of geyser complete all as specified and as directed.

Supply only geyser safety valve suitable for existing size, type & make of geyser complete all as specified and as directed.

Supply only PVC pipe connection of heavy duty for inlet, outlet connection suitable to withstand the pressure and temperature complete all as specified and as directed.

Supply only aluminium/chromium type flecxible connection, heavy duty for inlet, outlet connection suitable to withstand the pressure and temperature complete all as specified and as directed.

Supply only inner tank made out of steel sheet conforming to IS, suitable for 25 litres capacity of geyser, vertical type complete all as specified and as directed.

Supply only inner tank made out of steel sheet conforming to IS, suitable for 35/50 litres capacity of geyser, vertical type complete all as specified and as directed.

Supply only proper glass wool filling in between inner and outer tank of geyser of 25/50 litrs capacity of any make/type complete all as specified and as directed.

Supply only non return valve made out of brass fixed in vertical position of suitable dia complete all as specified and as directed.

Supply only new base assembly with inlet and outlet pipe made out of steel sheet with gasket and proper size of nuts, bolts and washer etc suitable for 25 litres capacity of geyser complete all as specified and as directed.

M&L for complete servicing and repair of DG set capacity 62.5 KVA including replacement of Engine oil and all types of filters as per manufacturers manual and as directed by Engineer in Charge. NOTES: - (i) Engine oil, oil filter, coolant replacement will be measured and paid separalety under revelant item. (ii) 'B' check shall be carried out by the authorised dealer of kirloskar/ Crompton Greaves and certificate of 'B' check shall be produced by the contractor from authorised dealer of Kirloskar / Crompton Greaves (iii) Testing equipments required for `B' check shall be of contractor's responsibility.

Supply only Special engine oil 20 W 40 grade all as recommended by manufacturer for first filling in the new DG sets complete all as specified and directed. Make: Kirloskar/ Castrol

Supply only Coolant concentrate for filling in radiator of DG set complete all as specified and directed. Make of coolant: Castrol or equivalent make as approved by GE.

M&L for cleaning of radiator assy by means of dismentlling from engine completely, flushing out complete old coolant/water ,cleaning by chemical wash , soldering /brazing complete and reassembling the same to the engine for smooth and efficient functioning complete all as specified and directed.

Supply only Lubricant oil filter element suitable for engine which has to be repaired at site/workshop complete all as specified and directed by Engineer-in-Charge.

Supply only Fuel filter suitable for engine which has to be repaired at site/workshop complete all as specified and directed by Engineer-in-Charge.

Supply only Fuel filter housing suitable for engine which has to be repaired at site/workshop complete all as specified and directed by Engineer-in-Charge.

Supply only belt suitable for engine which has to be repaired at site/workshop complete all as specified and directed by Engineer-in-Charge.

Supply only Hose pipe for air cleaner including hose clips suitable for engine which has to be repaired at site/workshop complete all as specified and directed by Engineer-in-Charge.

M/S BADRI NATH GUPTA

VIKAS ENTERPRISES