CA NO GE(H)-24/2024-25 SPECIAL REPAIR TO BLDG P-1487, P-1488, P-1472 AND OTHER SANCTIONED WORK IN THE AOR OF AGE B/R-I UNDER GE HISAR AT HISAR MIL STN.

Amount

Taking down chowkat or frame with shutters area not exc. 1.5 Sqm each (without taking off the wooden shutters from the frame) including cutting holes for hold fasts noth / disturbed portion with pcc 1:3:6 complete all as specified

Taking down chowkat or frame with shutters area exc 1.5 Sqm but not exc 4 Sqm each (without taking off the wooden shutters from the frame) including cutting holes for hold fasts noth / disturbed portion with pcc 1:3:6 complete all as specified.

S&F pressed steel frames of size 105mmx60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc. complete all as specified and directed.

Supply and fixing factory made 35 mm thick plain framed, paneled shutter (Two panels) with lock rail and panel of 9mm thick BWP commercial ply or 12 mm thick veneered particle board with commercial veneering on both faces, size of rail and styles as per IS : 1003 (Part-I), kiln seasoned and chemically pressure treated using second class Hard Wood rail and styles, fixed to chowkat, complete all as specified & directed.

S&F factory made Steel windows, ISI marked, (Box Type) with side hung shutters including box type hinges with steel handle etc complete with glazing bars dovetailed or welded including one shop coat of Zinc chrome primer including making good disturbed surfaces of walls, and including taking down old U/S steel window complete. DRG NO. CEJZ/TD-2013/01 sheet (1/3, 2/3, 3/3) Notes:- (i) The rate quoted by the contractor are deemed to be included for one shop coat of red oxide zinc chrome primer on steel windows. Nothing shall extra paid on this account. (ii) Glass pane/wire gauze/ guard bar shall be measured and paid separately.

S&F factory made Steel windows, ISI marked, (Box Type) with side hung shutters including box type hinges with steel handle etc complete without glazing bars dovetailed or welded including one shop coat of Zinc chrome primer including making good disturbed surfaces of walls, complete and including taking down old U/S window Notes:- (i) The rate quoted by the contractor are deemed to be included for one shop coat of red oxide zinc chrome primer on steel windows. Nothing shall extra paid on this account. (ii) Glass pane/wire gauze shall be measured and paid separately.

S&F steel ventilator with top hung shutter including hinges, steel peg stay, handle including one shop coat of Zinc Chromate primer complete all as specified.

Dismantling of wrought iron or mild steel work of any description not otherwise provided for in this Schedule all as specified & directed.

S&F mild steel framed work such as grills, gratings, etc with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks, cooler stand and similar work including welding conforming to Grade E-165 (Fe 290), complete, all as specified & directed.

M&L for preparation of new surfaces of wood or wood based materials of any description over 10 cm width or girth and applying two coats of synthetic enamel paint of approved tint over a coat of pink primer complete all as specified and directed.

M&L for preparation of new steel and iron surfaces of any description over 10 cm in width or girth and applying two coats of synthetic enamel paint of approved tint over a coat of zinc chrome primer complete all as specified and directed.

M&L for PCC 1:2:4 type B0, using 12.5mm graded crushed stone aggregate as in filling up chowkat , hold fast, bed block and similar works as directed, complete, all as specified.

Supply and fixing 3mm thick sheet glass ordinary quality and glazing with oil putty in square not exc 0.5 sqm in each pane including painting / oiling to new putty to match with the existing/new surfaces complete all as specified.

Supply & fixing butt hinges of size 100mm medium weight, cold rolled mild steel ISI marked complete all as specified

S&F 300mm long aluminium alloy, anodized, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified.

S&F 200mm long aluminium anodized barrel tower bolts of extruded section (ISI marked) complete all as specified.

S&F extruded aluminium alloy handle, 150mm size, fabricated type, anodized (ISI marked) complete all as specified.

S&F Floor door stopper of aluminium alloy body double legged with rubber shoe, fixed to bottom rail of door complete all as specified.

Demolition of cement concrete (un-reinforced) in ground floor and paving not exc 15 cm thickness (below or above ground level) complete, all as directed.

M&L for 100mm thick PCC 1:2:4 type B1 using 20mm graded crushed stone aggregate as in floor finished for garage and ramp all as directed.

M&L for 75mm thick PCC 1:3:6 type C1 using 20 mm graded crushed stone aggregate as in plinth protection surface finished fair and even complete all as specified. Note :- Plinth protection shall be of width as directed and shall be laid to slope of 1:30 in alternative bays not exceeding 3 meter in length. Joints of 6 mm wide and 10 mm deep shall be provided along the wall and bays and same shall be filled with bitumen mastic (1:3).

M&L for 50mm thick PCC 1:2:4 type B2 using 40mm graded crushed stone aggregate as in sub base as directed) all as specified and as directed.

M&L for machine cut Kota stone slab flooring 18 to 20mm thick laid over & including screed bed or bedding layer of 15mm thick in CM 1:6 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete all as specified. Note : - Kota stone shall be of size 550mm x 550mm (minimum) when brought at site.

M&L for Kota stone slab 15mm thick in riser of bricks steps & riser of staircase , skirting, dado and pillar laid over cement screed and jointed with pigment to match the shade of the slab including rubbing and polishing with & including backing coat in 10mm thick CM (1:3) to receive Kota Stone complete all as specified and directed (Note : Single piece tiles will be placed on the surface of stair case riser area).

Demolition of cement concrete (reinforced) of any description and in any position not otherwise specifically provided for in this Schedule complete all as specified.

M&L for reinforcement TMT bars 10 mm dia and over cut to length, bent to shape required, including cranking, bending spirally or hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia complete all as specified.

All as per serial item No. 26.00 here-in-before but 5 to 10mm dia in stirrups, spacers and binders.

M&L reinforced cement concrete (nominal mix) 1:2:4 type B1 using 20mm graded stone aggregate in slabs supported on walls, beams and columns in floors, roofs, shelves and the like. Note :- Reinforcement & formwork shall be measured and paid for separately.

Demolition / dismantling existing roof treatment , complete, all as directed.

M&L for preparation of roof surfaces (old or new) with wire brush drying and cleaning to remove all foreign materials and washing with water to remove loose particles with and including providing 40 mm average thick PCC 1:2:4 type B-0 (using 20mm graded stone aggregate) with maintain the proper roof slope complete all as specified and directed.

M&L for Priming surfaces and applying normal treatment (for moderate conditions), using glass fibre base bitumen felt, grade 2 all as specified and directed.

M&L providing APP based polymeric membrance miimum weighing 3 Kg / Sqm and minium 3 mm thick reinforced with polyster non woven fabrick (wt not less than 150 gms/Sqm) laid on primed surface by torch application including priming complete all as specified.

M&L for cement concrete 1:2:4 type B0, using 12.5mm graded crushed stone aggregate as in roof kerbs or mud stops, rounded or chamfered on edges all as specified.

S&F 20mm bore mild steel powder coated curtain rod with 02 Nos decorative ball type brackets (for each opening) and 02 Nos decorative side stoppers (for each opening) fixed on wall with wooden gutties & screws complete all as specified & as directed.

Demolition of brick/stone masonry built in cement/lime mortar of any mix and stacking serviceable stones aside for reuse & removing unserviceable materials in low laying area, complete, all as directed.

M&L for brick work with old size sub-class ‘B’ bricks, straight or curved on plan exc 6.00 metre mean radius, built in cement mortar 1:6 complete all as specified.

Taking down cement plaster or cement lime plaster on PCC/stone surface/brick surfaces including raking out joints hacking for key scrubbing down with water etc all as directed

M & L for rendering 15mm thick in cement mortar 1:6 on faces of brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified.

Material and labour preparation of new plastered surfaces and applying two coats of oil bound distemper of approved shade/tint over a coat of primer on walls including two coats of wall care putty all as specified & directed

Material and labour preparation of newly plastered surface of walls & applying three coats of white wash complete all as specified.

M&L rendering 5mm thick in cement mortar 1:3 on concrete surfaces in ceiling, finished even & smooth without using extra cement complete all as specified

Material and labour preparation of newly plastered/asbestos cement surfaces of ceilings & applying three coats of white wash complete all as specified.

M & L for rendering 15mm thick in cement mortar 1:4 on faces of brick work or concrete surfaces of walls, finished even and smooth without using extra cement including mixed with and including liquid water proofing compound @200 ML per 50 KG by weight of cement complete all as specified and directed.

M&L for preparation of newly plastered surfaces of wall & applying two coats of cement base paint of approved shade/tint on walls over a coat of primer all as specified & as directed.

M&L for preparing the old decorated plastered /un plastered surfaces of walls including cornices by brooming down or steel wire brushing scrapping down or steel wire brushing scrapping down smoke soot etc. and applying one coat of cement base paint of approved shade/tint on wall surface to give uniform and smooth surface etc complete all as specified and as directed.

M&L for preparation of old surfaces (plastered or unplastered) of walls including cornices, pilasters etc including brooming or steel wire brushing, scrapping down smoke soot, moulds, moss, efflorescent salts, trading oil, greasy spots and applying one coat of white wash complete all as specified & as directed.

M&L for preparing the old decorated plastered /un plastered surfaces of ceilings including cornices by brooming down or steel wire brushing scrapping down or steel wire brushing scrapping down smoke soot etc and applying one coat of white wash to give uniform and smooth surface etc complete all as specified and directed.

M&L for preparing new plastered or unplastered surface of walls and finishing walls with Acrylic smooth exterior paint of required shade. New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm of same make complete all as specifeid and directed.

M&L for preparation of old painted steel and iron surfaces of any description over 10 cm in width or girth and applying one coat of synthetic enamel paint of approved tint all as specified & as directed.

M&L writing letters or figures (Block, Roman, Italic or Indian) not exc. 30cm high with thick synthetic enamel paint of approved tint all as specified & as directed. Make : Berger/Johnson & Nicholson/Asian/Shalimar, 1st quality

Taking down and refixing in the same opening the heavy steel gate of garrages n exc 20Sqm

Providing and erecting steel props (upto full height, braced at centre, resting on wedge and block to support the structure provisionally during repair work and maintaining them in positon till reqd and as directed.

Chipping of loose/ damaged / cracked / previously repaired/ delaminated or weak concrete by chieseling to expose the sound core concrete where ever required and to expose rusted reinforcement upto depth n.exc 50mm and disposal of rubbish off the premises to a distance not exc 50 mtrs including cleaning of reinforced concrete surface by air compressor complete all as specified and directed.

Supply and apply of rust remover cum passivator to remove rust from existing reinforcement by using Product : Rustoff-100 of Sika or equivalent make in Fosroc / Thermax as approved by GE, with density : 1.01 Kg/ltr at 30°C and consumption : 0.2 kg/Sqm/coat complete all as specified and directed. Note : The material to be applied thoroughly on exposed rebars only with the help of a brush of suitable size. The area will be measured as length of bar x two times the dia of bar

Supply and apply cement based polymer modified rebar corrosion protection system to existing reinforcement using cement based polymer modified rebar corrosion protection system with consumption : 3.75 kg/Sqm for two coats and product requirements: carbonation resistance : 2 mm of SikaTop Armatec®-108 of Sika or equivalent make in Fosroc / Thermax as approved by GE corresponds to 20 mm of normal mortar; bond strength > 1N/Sqmm according to ASTM C 882-78 complete all as specified and directed. Note : The material to be applied thoroughly on exposed rebars only with the help of a brush of suitable size. The area will be measured as length of bar x two times the dia of bar

M&L for Providing, mixing & applying two component Epoxy resin concrete Bonding coat on prepared RCC surfaces as per manufacturer’s specification including prepartaion of surface throughly and cleaning complete where ever required with using Product : Sikadur®-32 LP of Sika or equivalent in Fosroc / Thermax as approved by GE with consumption : 0.4 kg/Sqm and Product requirements : Comp with ASTM C 881-78, Type II Grade 2 Class B+C complete all as specified and directed.

M&L for providing by mixing and trowel application of prepacked, light weight, two component structural grade polymer modified fibre reinforced thixotropic cement mortar Sika Monotop 122F of Sika or equivalent make in Fosroc / Thermax as approved by GE at an average thickness exceeding 10mm and upto 25mm to the prepared concrete substrate in soffit of slabs, beam, columns, parapets, fins and facias at any height, including finishing of applied Polymer mortar as per the technical specifications and manufacturer's instructions complete all as specified and directed.

M&L for weld-mesh of size 75x75x3mm to be wrapped on the exposed surface of rib of beam & on the slab bottom and tack welding to the exposed reinforcement at close intervals and gunite with cement mortar 1:3 mixed with admixture Sika Plasto creat plus or equivalent make in Fosroc / Themax as per manufacturer's instructions as approved by GE around rib of beam or roof slab of thickness n.exc 40mm to be applied under an operating pressure. The gunited surface to be cured properly for a min of 7 days all in complete as per the technical specifications and manufacturer's instructions and directed.

Providing and fixing water tight centering & shuttering and Scaffolding including bolting, strutting, propping etc. Including removal of from work from column, beam, slab and chajja etc. complete as per site requirement and directions of Engineer-in-Charge.

Supply and apply a ready to use non shrink, cementitious free flow micro-concrete (<100 mm) using Product : SikaRep Microcrete-4 + adequate coarse aggregate, Yield:approx 17 Ltr/bag (30 Kg) (depending on the size and quantity of coarse aggregate added), Product : SikaRep Microcrete-4 or equivalent make in Fosroc/Thermax as approved by GE. Product requirements: compressive strength > 60 N/Sqmm (28 days) according to ASTM C 1107-99 complete all as specified and directed.

M&L for providing and fixing 12-16mm dia injection ports non returnable nozzle by drilling, cleaning and sealing holes 50-75mm deep at 200mm c/c with fast setting high stength Epoxy putty, solvent free, three component compound based on epoxy resins, graded filters and thixotropic agnts using Sikadur 31 of Sika or equivelent make in Fosroc / Themax as approved by GE as in beams, columns, slab and parapets as per the technical specifications and manufacturer's instructions complete all as specified and directed.

M&L for grounting of nozzles with low viscous moisture insentive, high strength, eposy resin grout with Sikadur 52 LP (IN) of Sika or equivelent make in Fosroc as approved by GE with pressure not exceeding 2-3 KG/Sqcm till the nozzle refuse to take further grout including cutting extra length of the nozzle after the grout hardens and finishes as per the technical specifications and manufacturer's instructions complete all as specified and directed.

M&L cutting holes into or through RCC work as in slabs, chajjas etc including reinforcement is cut through if required and making good in cement mortar 1:3 or PCC 1:2:4 type B0 as required for superficial area exc. 100 but not exc. 250sqcm all as directed.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws or ‘L’ type or ‘J’ type or cranked hooks bolts complete all as specified & directed.

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws or ‘L’ type or ‘J’ type or cranked hooks bolts complete all as specified & directed.

S&F 1.25 thick mild steel plain, black sheet in wall clading, steel gates and similar work, cut to size, holes punched, including round headed screws, clout nails or rivers and fixed to wood or steel framing with plain 40mm lap joints with riverted or welded seams, including bending or truning up, mitered angles, etc as required complete all as specified and directed.

S&F mild steel framed work as in steel frames, chowkats, doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging, also fastening and fixing, conforming to Grade E-165 (Fe 290), complete, all as specified & directed.

M&L for hardcore of broken stone or boulders, gauge not exc. 63mm, deposited, spread and leveled in layers not exc 15 cm thick, watered and rammed to a true surface all as directed.

M&L reinforced cement concrete 1:2:4 type B1 using 20mm graded stone aggregate in beams, cantilevers, bressummers, lintels over 1.5m span and the like. Note :- Reinforcement & formwork shall be measured and paid for separately.

M&L formwork to sides and soffits of floor or roof beams, beam haunching, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. for rough finished flat surfaces of concrete.

M&L for rough cast finish plaster by applying the under coat of cement and sand mortar 1:3 not less than 10 mm thick and while it is still in plastic state the roughcast mixture consisting of crushed stone or fine gravel aggregate (size between 6 to 12 mm depending on the texture required) mixed with coarse sand and cement in the ratio of 1: 1: 1 shall be applied and finished even complete .

M&L for preparation of newly plastered surfaces of wall & applying two coats of OBD of approved shade/tint on walls over a coat of primer all as specified & as directed.

S&F rolled mild steel work as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats, necessary welding etc. conforming to Gde E-250 (Fe 410-W) quality `A’ ISI marked (IS-2062) all as specified and as directed.

S&F rolled mild steel work as in Plates (plain or chequered) channels, Square cut or notched (ordinary and counter sunk) forming holes, without any attachment including necessary welding etc. conforming to Gde E-250 (Fe 410-W) quality `A’ all as specified and as directed.

M&L for 100mm thick PCC (1:4:8) type D2 using 40 mm graded crushed stone aggregate as in sub base, surface finished fair and even complete all as specified.

M&L for PCC 1:2:4 type B-1 using 20mm graded crushed stone aggregate as in levelling course of floors and roofs 25mm thick finished fair & even complete all as specified & as directed.

M&L for mirror polishing on marble / granite/ machine cut Kota stone where ever required to give high gloss finish polishing complete all as specified.

S&F Anodised aluminium snap grid size 605 x 605mm frame work for false ceiling including hangers 6mm dia GI (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia 40mm long complete all as specified.

S&F Gypsum board 9-12mm thick duly finished surface (thin PVC layer on gypsum board as per maunfacturer's instructions) of size 595mmx595mm thick and the same shall be placed in snap grid as in false ceiling complete all as specified and directed. Note : The snap grid frame work shall be measured & paid for separately

S&F collapsible steel gates, top hung, consisting of channel pickets, piovted flat bars, top and bottom runers, brass handles etc.. As specified, erected in position and securing runers with holdfasts and brackets complete all as specifeid and as directed.

M&L for chequered cement concrete coloured tiles, 20cm x 20cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors with grey cement & pigment, laid over & including 20mm thick screed bed in cement & sand mortar 1:4, complete, all as specified & as directed.

M&L for precast cement concrete 1:2:4 type B-1 using 20mm graded crushed stone aggregate as in kerb block (factory casted) with plain fair faces, including weathering, slightly rounded or chamfered angle throating, with plain or interlocking joints and setting in cement mortar 1:4, complete, all as directed.

S&F Expanded metal, cut to length, bent to shape required and tying with and including annealed mild steel wire not less than 0.9mm dia or fixing with galvanised steel staples supplied and fixed to wood or steel members complete all as specified and as directed.

Surface excavation not exc 30cm deep and averaging 15cm deep and getting out in soft/loose soil.

Surface dressing not exceeding 15 cm depth and getting out in soft /loose soil including clearing away all grass and vegetation saplings , shrubs , bushes , undergrowth roots and removing rubbish upto a distance n exc 50 mtrs outside the periphery of the any installation/ feeder pillar area etc. Note:-The contractor will ensure that no vegetation grows during the contract period on the area so dressed.

Excavation in trenches in soft/loose soil n exc 1.50 meter wide and n exc 1.50 meter in depth for foundation of pole, laying cable etc and getting out etc complete all as specified and directed.

Returning, filling in including spreading, leveling, watering and well ramming in layers n exc 25 cm thick etc complete all as specified and directed.

Removing excavated surplus soil to a distance not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5 mtr above the starting point etc complete all as specified and directe.

Taking down carefully copper/aluminium point wiring (light/fan/socket or power) complete including taking out existing unserviceable terminal boxes & conduit with switches/sockets/fan regulators and fittings such as ceiling rose, pendants, tube light fittings, lamp holders, brackets light fittings, rectangular blocks, DB, MCB etc. and making good disturbed surface of walls, floors etc. to match with the existing surface etc complete all as specified and directed by Engineer-in-Charge.

M&L for point wiring for one light point controlled by one, one way switch with 1.50 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade including 1.50 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade as continuous earth wire in green colour to common earth and connected to earth dolly laid/drawn into and including concealed PVC rigid non metallic conduit 25mm dia medium grade (ISI marked) with all fittings such as tees, bends etc including modular sunk type pressed steel box covered with and including modular press steel with cover plate and frame ’, complete, all as specified & directed. (Note :- Switches, sockets etc shall be measured and paid for separately under appropriate items of BoQ' ).'

All as per item No 90.00 (here-in-before) but ceiling fan /exhaust fan point controlled by one Number one way switch.

All as per item No. 90.00 (here-in-before) but for one 5 Amp socket outlet on independent board controlled by one Number one way switch on independent board

All as per item No. 90.00 (here-in-before) but for one 5 Amp socket outlet on the same board controlled by one Number one way switch on same board.

All as per srl item No. 90.00 (here-in-before) but for 15 Amp socket out let by using 2.50 Sqmm PVC insulated unsheathed copper conductor cable FRLS multi stranded on independent board including provn of 2.50 Sqmm unsheathed, multistranded copper conductor cable FRLS continues as earth wire connected to earth dolly etc complete all as specified and directed by Engineer-in-Charge.

Supply and fixing modular type switch 1 way 6Amp, 230Volts 1 module complete all as specified and directed

Supply and fixing modular type switch 1 way 16Amp, 230Volts 2 module complete all as specified and directed

Supply and fixing modular type socket outlet 6Amp - 5 pin combined 2 modle 230 volts AC complete all as specified and directed

Supply and fixing modular type socket outlet 6Amp/16 Amp - 3 pin combined 2 modle 230 volts AC complete all as specified and directed

M&L for point wiring for one light point controlled by one, one way switch with 1.50 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade including 1.50 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade as continuous earth wire in green colour to common earth and connected to earth dolly laid/drawn into and including concealed PVC rigid non metallic conduit 20mm dia medium grade (ISI marked) with all fittings such as tees, bends etc including sunk type pressed steel box covered with and including 3 mm thick new bakelite laminated sheet top cover ‘Hylam’, complete, all as specified & directed. (Note :- Switches, sockets etc shall be measured and paid for separately under appropriate items of BoQ' ).'

S&F Sub main wiring with two single core cable PVC insulated unsheathed of copper multi stranded conductor FRLS cable of size 2.5 sqmm, 1100 votls grade drawing through and EXISTING concealed conduit 25 mm dia medium duty including acessories such as Tee, bend, Elbow etc, ISI marked with and including PVC insulated 2.5 sqmm unsheathed multistranded FRLS copper conductor cable for earth continuity and connected to common earth dolly including cutting chasing of wall, if required and making good disturbed surface in CM (1:3) and finishig the surface to match with existing surface, etc complete all as specified and directed by including taking down old unserviceable submain wiring. Note:- Two lengths of 2.5 Sqmm cable, one length of 2.5 Sqmm cable and one length of PVC conduit will be measured as one length.

S&F switch piano, flush type, single pole, one way, 5/6 Amp, 230 Volts all as specified & directed.

S&F switch piano flush type, single pole, one way, 15 Amp, 230 Volts.all as specified & directed.

S&F flush type socket outlet multipurpose 3 Pin 15/16 Amp 230 volts AC complete all as specified and directed.

Supply & Fixing in replacement ceiling Fan 1200mm sweep 210 cfm Decoreted type with electronic regulator, with down rod , canopy, rubber reel etc including provision of three single core 0.5 sqmm copper conductor flexible cable connected from ceiling rose to fan and suitable size MS bolts, nuts for fixing ceiling fan complete all as specified and directed.

S&F fan regulator step type step 120/180 watt cap of polycarbonite complete all as specified & directed.

Supply and fixing LED tube light fitting 20 watt with electronic driver ultra slim with rxtured poly carbonate difuser for glare free light distribution complete all as specified and directed.

S&F sheet metal enclosure distribution board TP&N, 4 way, double door, powder coated, protection class IP-42, suitable for mounting MCB, DBs confirming to IS-13032, IS-8632, BS-5484 with min 200 Amp rating copper bus bar, complete all as specified & directed.

S&F in replacement MCB TPN of capacity 63A,10 KA, type 'B', 415 volts complete all as specified and directed.

S & F LED bulb lamp 9 watt capacity complete all as sepcified and directed.

S&F lamp holder, insluated body, with back plate suitable for batten fittings & complete all as specified & directed.

S&F ceiling rose surface bakelite 65mm x 50mm, 3 terminals with back plate etc complete all as specified and directed.

S&F modular type Ceiling fan regulator electronic step type of suitable wattage, 230V suitable for 1200/1400 mm ceiling fan etc complete all as specified and directed

S&F in replacement LED light fitting 1x40W, regal batten for LED incl ultra bright glass LED tube light aluminium housing with very high efficiency, singel / double side connection all as specified and directed.

S&F in replacement street light LED light fitting 20 Watt, pressure die cast housing with epoxy powder coating, IP65, connected with and including 0.5 sqmm flexible copper multistranded conductor cable including security light bracket made to shape out of GI pipe 25mm dia light grade 1.5m length and fixed with MS clamps of size 40x5mm - 2 Nos, nuts, bolts and washers fixed on wall all as specified and directed. Make : Cat Part No ENDURAPEARLSL20WLED757SASYTOPCMP of Havells or Cat No LTESSI20WLED of C&S or equivalent of make as mentioned in Appx 'C' list of makes here-in-after

S & F MCB SP, 6 to 32 Amps 240 Volts , 'C' curve, 10 KA, IS-8828 marked for fixing in DB complete all as specified & directed. . Note :-Make of MCB shall be same of that DB.

S & F MCB SPN, 40-63Amps 240 Volts , 'C' curve, 10 KA, complete. Note :-Make of MCB shall be same of that DB.

S&F MCB TPN, 63 Amps 415 Volts , type 'C' curve, 10 KA, IS-8828 marked fixing in DB complete all as specified & directed. Note :-Make of MCB shall be same of that DB.

S&F sheet metal enclosure distribution board SP&N, 08 way, double door, powder coated, protection class IP-43, suitable for mounting MCB, DBs confirming to IS-13032, IS-8632, BS-5484 with min 200 Amp rating copper bus bar, complete all as specified & directed.

S&F sheet metal enclosure distribution board TP&N, 4 way, double door, powder coated, protection class IP-42, suitable for mounting MCB, DBs confirming to IS-13032, IS-8632, BS-5484 with min 200 Amp rating copper bus bar, complete all as specified & directed.

S&F sheet metal enclosure distribution board SP&N, 08 way, double door, powder coated, protection class IP-43, suitable for mounting MCB, DBs confirming to IS-13032, IS-8632, BS-5484 with min 200 Amp rating copper bus bar, complete all as specified & directed.

M&L for earthing complete with galvanized steel earth plate electrode 60cmx60cmx6mm thick burried directly in ground (earth pit not less than 2.25 m deep below ground level) with top edge of plate not less than 1.5 m deep below normal ground level and connected to and including galvanized iron earth wire 4 mm dia by means of GI nuts, bolts, check nuts, washers thimbles, etc as shown in electrical plate No 3 of SSR Part-I and connection to main switch board/Test point/panel/equipment and testing on completion including excavation and earth work in any type of soil, returning filling in, and removal of surplus spoil to a distance not exc 50 metre, charcoal and salt in alternate layer 15 cm thick all around the earth plate electrode, MS funnel with wire mesh, GI pipe medium grade 20 mm bore for watering and 15 mm bore upto 7.50 metre long GI pipe light grade for earth wire protection fixed with poles/wall with two clamps, made from MS flat 25 mmx3mm, bolts, nuts and washers, PCC chamber (1:3:6) type C1, 40mm thick precast RCC cover 1:2:4 type B1 shall be provided on CI frame etc complete all as specified & as directed including dismantling & taking out old existing unserviceable earthing. Note :- PCC chamber shall be constructed at least 1.5m away from the earth electrode and pipe for watering shall be provided in slanting manners.

Supply and fixing ceiling fans (Copper widing) complete with blades, down rod and accessories, 230V, 1200mm sweep, min air delivery 210 CFM, BEE five star rated with brushless direct current motor (BLDC) with remote complete all as specified and directed.

Supply , laying , jointing, testing and commissioning of size 10 sqmm 2core LT underground cable , 1100 volts grade, XLPE insulated and PVC sheathed, strip armoured heavy duty with multistrand aluminium conductors IS-7098, laid in trenches /fixed on wall /floor /road /culverts /pole or encased in GI pipe complete all as specified. Note : Sand cushioning, cable protection, GI protection pipe, clamps, jointing kits and excavation & earth work shall be measured & paid for separately.

Supply , laying , jointing, testing and commissioning of size 10 sqmm 4core LT underground cable , 1100 volts grade, XLPE insulated and PVC sheathed, armoured heavy duty with multistrand aluminium conductors IS-7098, laid in trenches /fixed on wall /floor /road /culverts /pole or encased in GI pipe complete all as specified and directed. Note : Excavation, earth work, sand cushion & brick protection shall be paid separately.

S&F LED highway light 72watt light complete with driver suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and directed by Engr-in-Charge.

Supply and fix in repair MS heavy duty down rod of 15mm dia and 1000mm length with necessary cutting / drilling holes and painting for ceiling fans complete all as specified and directed.

Supply & fixing and testing exhaust fan of 480mm sweep heavy duty, double ball bearing, 1400 RPM, suitable for SP 230 / 250 volt, 50 Hz AC supply complete with louver shutter including fixing / grouting of frame in wall & cutting opening complete with covers & connecting with & including 3 Nos 1.5 sqmm single core, PVC insulated but unsheathed FRLS 1100 volts grade cable with multi-stranded copper conductor from ceiling rose to fan complete

S&F wall mounted air circulated fan 600mm sweep, Aerodynamically designed blades for high air delivery, powerful copper motor designed, min 1350RPM, adjustable tilt oscillating, button control complete all as specified and directed.

M&L for brick covering to underground electric cable using sub class ‘B’ bricks, laid dry, flat, perpendicular to the direction of cable etc complete all as specified and directed.

M&L for Sand cushioning 230mm thickness with dry sand (one layer of 80mm thickness before laying of cable and other layer of 150mm thickness after laying of cable) and punned down to 180mm after laying of cable in trenches for protection of cable complete all as directed. Note :- For the purpose of payment only punned thickness shall be measured.

M&L for Boring holes horizontally under road crossing manually for crossing of GI pipe/HT/LT cable etc up to 200 mm bore all as directed

Supply and lay GI pipe light grade in replacement as cable protection laid on trench/floor, fixed on pole/wall etc of following sizes all as specified of size 100 mm dia Make:- Jindal, Tata, Surya prakash

Supply and laying XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cables with aluminium conductor 1100 volts grade 3.5 core 35 sqmm

Material and labour for river washed and screened, dry sand for filling in trenches below and around underground cables for cushioning of cables etc, complete all as specified.

Supply and fix Voltage stabilizer for automatic operation, three phase, naturally oil cooled, indoor type & designed for input variation between 300 V to 480 V with output voltage stabilized at 415 with accuracy + 2.5% and speed of correction 8 Volts per second and of capacity 10 KVA .

S&F (in replacement) change over switch 63 Amps OFF load (side handle) in sheet enclosure four pole to be fixed on wall with FI 32x6mm, nuts, bolts, washers etc complete with all electric connection complete all as specified and directed.

S&F 1100 volts grade heavy duty cable PVC insulated , 10Sqmm aluminium conductor served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 meter apart including 4mm suspension wire, one twin core cable flat. complete all as specified and directed.

m/s krishna engineers1 (BID ID -3051692)

Siya constructions (BID ID -3051707)

moti construction company (BID ID -3051982)

malik constructions (BID ID -3051616)