Special Repairs to Bldg No P-6/1 -08 (ORs MD accn) at Napier Qtr at Auto Regt and Provision of Amn Bay (Trg Shed) at KK Ranges in the area of AGE B/R II under GE (N) Ahmednagar

Amount

Demolition of Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) etc complete all as specified and directed by Engineer-in-Charge.

Demolition of brick/ stone masonry/block masinry built in cement or lime mortar etc complete all as specified and directed by Engineer-in-Charge.

M&L Cutting out bricks, forming toothing for, and bonding new into old work including value of new materials entering old walls and jointing and pointing (measured on vertical face in contact with old wall only), in cement and sand mortar (1:6) etc complete all as specified and directed by Engineer-in-Charge.

Taking down Chowkats or frames with shutters (without taking off shutters from the frames) n.exc 1.5 Sqm etc complete all as specified and directed by Engineer-in-Charge.

Taking down Chowkats or frames with shutters (without taking off shutters from the frames) exc 1.5 Sqm but n'exc 4.0 Sqm etc complete all as specified and directed by Engineer-in-Charge.

Taking down cement mortar plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed by Engineer-in-Charge.

Material and labour for providing water proofing treatment on roofs, as per manufecturer's instructions and as specified after taking down/out as existing at site :- (a) Cleaning the newly plastered surfaces with wire brushes and applying a coat of bituminous primer @ 0.30 ltrs/sqmts and allow to dry. (b) Applying and laying torch APP polymer modified bituminous membrance 3 mm thick with non woven polyster matt as reinforced weighing not less than 3 kg/sqmts by thermofusion process as per manufacturers specification including applying one coat of aluminium paint. Note : (i) Work will be carried out strictly by the authonticated applicator of the manufacturer and as per manufacturers specification as approved by GE. (ii) Certificate from manufacturer shall be submitted by the contractor.

M&L for pre- painted galvalume aluminum zinc coating GI based corrugated mangalore pattern steel sheet 0.50mm thick of red colour having tensile strength of 550 Mpa as in roof covering fixed with self tapping screws including dismantling corrugated steel sheeting, any gauge, thickness etc complete all as specified and directed by Engineer-in-Charge.

S&F Steel work in tubular trusses including special shaped washer etc. complete conforming to I. S.1161-1979 grade St.-240 etc complete all as specified and directed by Engineer-in-Charge.

S&F of steel work in post, Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. as per Fe 410 -W (Gde- E- 250) quality- A etc complete all as specified and directed by Engineer-in-Charge.

M&L for rendering 10mm thick in cement and sand mortar (1:4) over concrete surfaces finished even and smooth including water proofing compound as per manufacturers instructions etc complete all as specified and directed by Engineer-in-Charge.

Rendering 15 mm thick in cement and sand mortar (1:4) on fair faces of brick work or concrete surfaces and finished even and smooth without using extra cement including water proofing compound @ 3% of weight of cement etc complete all as specified and directed by Engineer-in-Charge.

M&L for rendering 5 mm thick in cement and sand mortar (1:3) on ceiling surfaces finished even and smooth etc complete all as specified and directed by Engineer-in-Charge.

M&L for PCC 1:2:4 Type B-1 (20 mm graded stone aggregate) as in hold fast blocks and rafter bed blocks and Gola etc complete all as specified and directed by Engineer-in-Charge.

M & L for 75mm thick PCC (1:3:6) type C-2 using 40mm graded mechanically crushed stone aggregate as in plinth protection finished even and smooth without using extra cement with & including 10mm wide, 30mm deep joints at the rate of 3.00 mt centre to centre and at every turning & filling the joints with bitumen & sand mixture etc complete all as specified and directed by Engineer-in-Charge.

M&L for 75 mm thick Cement concrete type B-2, 1:4:8 (40mm graded stone aggregate) as in sub base etc complete all as specified and directed by Engineer-in-Charge.

M&L for PCC (1:4:8) type D2 (using 40mm graded stone aggregate) as in foundation /mass concrete etc complete all as specified and directed by Engineer-in-Charge.

M&L for RCC Type B-1 1:2:4 using 20 mm graded stone aggregates as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete and floor slab etc complete all as specified and directed by Engineer-in-Charge.

M&L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips etc complete all as specified and directed by Engineer-in-Charge.

M&L for PCC solid block masonry type C1 (1:3:6) using 20 mm graded stone aggregate built in cement and sand mortar (1:6) , width exc. 10 cm etc complete all as specified and directed by Engineer-in-Charge.

M&L for Joint free ceramic tiles 600x600mm matt finish as in floor etc laid over and including screed bed 15 mm thick in cement and sand mortar (1:6) set and jointed with neat cement slurry and pointed with white or coloured cement to match the shade of tiles etc complete all as specified and directed by Engineer-in-Charge

Material and labour for joint free non skid ceramic coloured tiles size of each tile 400x400 mm 7-8 mm thick , as in floor etc laid over and including screed bed 15 mm thick in cement and sand mortar (1:6) set and jointed with grey cement slurry and pointed with white or coloured cement to match the shade of tiles etc complete all as specified and directed by Engineer-in-Charge

M&L for Glazed ceramic coloured tiles in vertical surface 450 x 300 x 7 mm thick laid over and including 10 mm thick back coat in cement and sand morter (1:4) set & jointed with grey cement slurry and pointed with white or coloured cement to match the shade of tiles etc complete all as specified and directed by Engineer-in-Charge.

Material and labour for 16 to 18 mm thick pre-polished granite stone slab of approved shade and colour Jet Black / Telephone Black as in top table, top of WHB, kitchen slab/platform, steps, gate pillars, cills etc or on vertical surfaces including vertical projection, full round moulding the edge laid over screed bed 15mm thick in cement and sand mortar (1:4) jointing & pointing in white cement 1:2 using marble dust with admixture of pigment to match the shade of granite and rubbing polishing expasosed edges to achieve mirror finish etc complete all as specified and directed by Engineer-in-Charge

Material and labour for machine cut cudappah stone slab 20-25 mm thick full round moulding the edge laid over and including 15 mm thick screed bed in cement and sand mortar (1:6), set and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing etc complete all as specified and directed by Engineer-in-Charge

M&L for providing and laying in repair Chequered cement concrete tiles 20cm x 20cm x 25mm thick, set, jointed and pointed in neat cement slurry as in floors laid over and including 15mm thick screed in cement and sand mortar (1:6) etc complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repairs vitreous china wash down water closet (Pedestal pattern) white including fixing bolts with and including plastic water closet seat cover closed pattern with flat bottom and cover and MSCP almn hinges device complete connecting to 'P' or 'S' trap etc complete all as specified and directed by Engineer-in-Charge.

Supply and fix in repairs Counter top wash hand basin vitreous China, flat back of size 450 X 300 mm including a pair of brackets, PTMT waste coupling, 32 mm dia PVC flexible waste pipe and connecting to stop valve and nahani trap etc complete all as specified and directed by Engineer-in-Charge

S&F in repairs stainless steel kitchen sink matt finish with draining over all size 950 X 510 mm and bowl size 410 X 410 X 230 mm, made out of 18 guage SS sheet of high quality including a pair of brackets, waste coupling, plug and chain, 32 mm dia PVC flexible waste pipe and nahani trap etc complete all as specified and directed by Engineer-in-Charge.

S&F in repairs stainless steel kitchen plate rack made out of 0.63 mm thick stainless steel sheet of size 36''x 36''x 10'' with complete accessories including screws etc complete all as specified and directed by Engineer-in-Charge.

Supply & Fix in repair CP health faucet with 8 mm dia 1 mtr long flexible tube wall mounted/hooked etc complete all as specified and directed by Engineer-in-Charge.

Supply and fix in repair Fancy type long body bib tap,foam flow, quarter turn,15 mm dia, CP cast copper alloy screwed down for iron pipe or for brass ferrule, min weight 400 gram each etc complete all as specified and directed by Engineer-in-Charge

Supply and fix in repair Fancy type two way bib tap,foam flow, quarter turn,15 mm dia, CP cast copper alloy screwed down for iron pipe or for brass ferrule, min weight 400 gram each etc etc complete all as specified and directed by Engineer-in-Charge

Supply and fixing in repairs stop valve/Angle cock cast copper alloy, fancy type screwed down, high pressure screwed both ends for iron pipe or for union and fix of size 15 mm bore, min weight 400 gram each etc complete all as specified and directed by Engineer-in-Charge

Supply and fix in repair 15 mm dia pillar tap,foam flow, quarter turn, swan neck long body heavy casted cast copper alloy, chromium plated, fancy type, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe etc complete all as specified and directed by Engineer-in-Charge

Supply and fix in repair 15 mm dia sink cock, foam flow, quarter turn, swan neck long body heavy casted cast copper alloy, chromium plated, fancy type, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe etc complete all as specified and directed by Engineer-in-Charge

Supply and fix in repairs, over head shower with long shower arm not less than 300 mm, shower rose fitted on adjustable pivot adjustable 100 mm dia etc complete all as specified and directed by Engineer-in-Charge.

S&F in repairs decorative towel ring recangular chromium plated fixed with (CP) brass screws with concel cap mn 60 mm dia, ring length minimum 210 mm minimum weight 200 gram each etc complete all as specified and directed by Engineer-in-Charge

S&F in repairs towel rod fancy type chromium plated fixed with (CP) brass screws etc complete all as specified and directed by Engineer-in-Charge

S & F in repairs looking mirror of size 600 mm x 450 mm with PVC decorative frame of 1'' width mounted on PVC sheet base etc complete all as specified and directed by Engineer-in-Charge.

S&F anodised aluminium window powdercoated and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 No.). hinges type B-21100mm long (2 No.) suitable handle (1 No.) etc complete all as specified and directed by Engineer-in-Charge.

Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P.brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge

Supply and fix 2nd class hardwood 35 mm thick factory made Plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats

M&L for 3.00 mm thick sheet glass ordinary quality and glazing with oil putty in square n exc 0.50 sqm in each pane etc complete all as specified and directed by Engineer-in-Charge.

M & L for 3 mm thick sheet frosted/pin headed glass ordinary quality and glazing with oil putty or wooden beads in squares n.exc 0.50 sqm in each pane etc complete all as specified and directed by Engineer-in-Charge.

M&L for 2 mm mesh, Wire netting of galvanised steel wire 0.71 mm dia fixed with tinned tacks of wire staples etc complete all as specified and directed by Engineer-in-Charge.

Supply and fix mild steel butt hinges medium weight cold rolled of size 100mm etc complete all as specified and directed by Engineer-in-Charge.

Supply and fix aluminium anodised barrel tower bolt of extruded section 150mm long etc complete all as specified and directed by Engineer-in-Charge.

Supply and fix aluminium alloy, anodised, sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded section of cast aluminium alloy and fixed 300mm long etc complete all as specified and directed by Engineer-in-Charge.

Supply and fix aluminium anodised handles of extruded section 150mm long etc complete all as specified and directed by Engineer-in-Charge.

S&F Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing etc complete all as specified and directed by Engineer-in-Charge.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification and drawing etc complete all as specified and directed by Engineer-in-Charge.

S & F Pressed steel door frame of size 125 x 60mm for doors with one or more rebates including necessary fixing lugs, hings, lock strike plate, etc complete all as specified and directed by Engineer-in-Charge.

Material and labour for preparation of new wood and wooden based surfaces of any description exceeding 10cm in width or girth and applying two coats of synthetic enamel paint over a coat of pink primer etc complete all as specified and directed by Engineer-in-Charge.

Material and labour for preparation of new steel surfaces of any description exceeding 10cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer etc complete all as specified and directed by Engineer-in-Charge.

M&L Forming jambs, etc., to openings (to foregoing item), with stone supplied by MES including cutting, toothings and properly bonding into old work, including facing and pointing (if necessary) to match existing work, complete in cement and sand mortar (1:6) etc complete all as specified and directed by Engineer-in-Charge.

Supply and fix PVC connections 15 mm size with PTMT nuts of length 600 mm etc complete all as specified and directed by Engineer-in-Charge

M & L for Taking up or down steel tubing 15 mm bore of pipes and connections etc complete all as specified and directed by Engineer-in-Charge

M & L for Taking up or down steel tubing 20 mm bore of pipes and connections etc complete all as specified and directed by Engineer-in-Charge

M & L for 16 mm outer dia of Pipe 3 Layer PP-R Polypropylene random copolymer concealed pipes SDR 7.4 (PN - 16) uv stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fitting fixed complete to walls, ceilings or in floors etc complete all as specified and directed by Engineer-in-Charge

M & L for 20 mm outer dia of Pipe 3 Layer PP-R Polypropylene random copolymer concealed pipes SDR 7.4 (PN - 16) uv stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fitting fixed complete to walls, ceilings or in floors etc complete all as specified and directed by Engineer-in-Charge

M&L for preparing new plastered surfaces of wall and applying two coats of OBD over a layer of 2mm thick putty finished with roller finish etc complete all as specified and directed by Engineer-in-Charge

M & L for preparation of new plastered surface of walls and applying two coats of exterior wather proof emulsion over primier etc complete all as specified and directed by Engineer-in-Charge

M&L for preparation of newly plastered surfaces of ceiling including cornices etc by brooming down or steel wire brushing, scraping down smoke soot, moulds, moss and efflorescent salt, trading oil and greasy spots and applying two coats of white lime wash at any height including scaffholding etc complete all as specified and directed by Engineer-in-charge.

S&F Stainless steel curtain rod 25 mm dia with stainless steel fixing brackets and screws and fancy type end globes at open ends etc complete all as specified and directed by Engineer-in-Charge.

S&F 12 mm thick Plywood, grade BWR, type BB, fixed with screws to timber frame work etc complete all as specified and directed by Engineer-in-Charge.

S&F 0.90 mm Decorative laminate type 1 of surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturer's instructions etc complete all as specified and directed by Engineer-in-Charge.

S&F 90 degree stainless steel (SS304) soft closing cupboard door hing concealed type with SS mount plate,SS screws and all accessories complete fitted as per manufacturer's instructions and as directed by engineer in charge Make sleek/Hettich/Spider or equivalent as approved by GE etc complete all as specified and directed by Engineer-in-Charge.

S&F 2nd class hardwood Plain fillets esc 13 Sqcm but n exc 25 Sqcm square, rectangular or triangular in section, clean sawn, secured with nails or brads etc complete all as specified and directed by Engineer-in-Charge.

S&F 100 mm stainless steel polished Concealed type cupboard /drawer handles including SS screws etc complete all as specified and directed by Engineer-in-Charge.

S&F in repair wall mounted cloth drying stand consisting of 16 mm dia powder coated MS rods of CR steel mounted on powder coated MS square pipe, 16- 4 rods, 4ft each, total weight not less than 3.80 Kg, fixed to wall including all fittings/accessories etc complete all as specified and directed by Engineer-in-charge Make -Easy dry Model: Mount it or Equivalent product in Nirali/Prayag.

Supply only intergral water proofing compound etc complete all as specified and directed by Engineer-in-Charge.

Surface excavation n.exc. 30 cm deep and averaging 15cm deep and getting out in hard/dense soil etc complete all as specified and directed by Engineer-in-Charge.

Excavation in post holes in hard/ dense soil ( or similar holes) each not exc 0.5, cum getting out in soft/loose soil, returning , filling in and ramming earth or broken rubble mixed with earth around, in layers not exc 25 cm, watering and removing surplus soil to a distance not exc 50 metre and making good surface etc complete all as specified and directed by Engineer-in-Charge.

Excavation in trences n.exc 1.5m wide and n.exc 1.5m in depth for foundation soft/disintegrated rock and getting out etc complete all as specified and directed by Engineer-in-Charge.

M&L for PCC (1:3:6) type C-2 using 40mm graded stone aggregate as in foundation filling and mass concrete etc complete all as specified and directed by Engineer-in-Charge.

Removing excavated (soil) material n.exc 50m and depositing where directed at a level n. exc 1.5m above the starting point etc complete all as specified and directed by Engineer-in-Charge.

M&L hardcore or gauge of brokenstone or boulders n.exc 63mm, deposited spread and levelled in layers n.exc 15cm thick, watered and rammed to a true surface etc complete all as specified and directed by Engineer-in-Charge.

M&L moorum filling in floors or paving laid in layers n.exc. 15cm thick spread levelled and rammed including watering etc complete all as specified and directed by Engineer-in-Charge.

M&L for PCC (1:2:4) type B-1 (using 20mm graded stone aggregate) 40mm thick as in floor surface finished even and smooth using extra cement etc complete all as specified and directed by Engineer-in-Charge.

M&L for rendering 15 mm thick in cement and sand mortar (1:6) on fair faces of concrete / block masonary / brick surface finished even and smooth without using extra cement etc complete all as specified and directed by Engineer-in-Charge

Returning, filling including spreading levelling, watering and well ramming in layers n.exc 25cm in layers n.exc 25cm in soft disintegrated rock etc complete all as specified and directed by Engineer-in-Charge.

M&L for preparing new plastered surfaces and applying three coats of white wash etc complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of new plastered surface of walls and applying two coats of cement paint on external surfaces etc complete all as specified and directed by Engineer-in-Charge.

M&L for machine pressed precast concrete glossy finish interlocking paver block any shape and size confirming to IS 15658-2006 of 80 mm thickness M-35 Grade with gray cement pigment over sand cushion 30mm etc complete all as specified and directed by Engineer-in-Charge.

M&L for filleting in any position and to any shape, Section of fillet exc. 25 but n exc. 50Sqm in cement mortar 1:3 including all mitres, stops, etc complete all as specified and directed by Engineer-in-Charge.

Taking down carefully copper/aluminum point wiring (light/fan/bell/socket, power point etc) complete , including fixture and fitting such as switches, ceilling roses, pendants, regulators, sockets, light fittings etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per condition seperately) and making good disturbed surfases of walls, floors etc complete all as specified and directed Engineer-in-Chage

M&L for point wiring complete on surface of wall (open) type with two runs of 1.5 sq mm for phase and neutral single core multistranded copper conductor of 1100 volts grade PVC insulated and unsheathed FRLSH cable drawn in and incl PVC Casing and capping ISI Marked with its accessories PVC boxes (upto 12 module suitble for Mylinc series of Legrand including white plates with frame upto 12 module of make suitable for Mylinc Series ) for fixing switches/socket/regulators etc incl 1.5 sq mm single core multistranded copper conductor of 1100 volts grade PVC insulated and unsheathed FRLS cable as earth continuity conductor to common earth & connecting to earth dolly for the following, all as specified and directed. Note : 1. Porper colour coding shall be adopted for wiring (For Phase- Red, Yellow, Blue, For Earth - Green and For Neutral- Black) 2. All points are required to earthed upto fixtures i.e. Holders, Tube lights, Wall lights, ceiling lights, bulkhead lights, bldg security light etc

One light point controlled by switch 5 Amp single pole one way

One fan point controlled by switch 5 Amp single pole one way

One bell point controlled by one switch 5 Amp single pole, one way on independent board

One 3 pin 5 Amp socket outlet on same board controlled by one, one way 5 Amp switch

One socket outlet 5/3 pin 5 Amp controlled by one switch on independent board

One light point controlled by switch 5 Amp single pole two way

All as per Item No 88 (here-in-before) but with 2.5 Sqmm Copper conductor cable for Phase , Neutral and Earth for one 3 pin, 15 Amp socket outlet on independent board

S&F bell Multi music type elelctric 230V AC single pole etc complete all as specified and directed by Engineer-in-Charge

S&F Modular Switch, 6 Amp, one way, one Module. etc complete all as specified and directed by Engineer-in-Charge

S&F Modular Switch, 6 Amp, two way, one Module. etc complete all as specified and directed by Engineer-in-Charge

S&F Modular Switch, 16 Amp, onw way, one Module. etc complete all as specified and directed by Engineer-in-Charge

S&F Modular Socket Outlet 6 Amp, 2/3 pin, combined two module etc complete all as specified and directed by Engineer-in-Charge.

S&F Modular Socket Outlet 6 Amp / 16 Amp - 2/3 pin combined two module etc complete all as specified and directed by Engineer-in-Charge

S&F Modular Bell push, 6 Amp, one module etc complete all as specified and directed by Engineer-in-Charge

S&F Modular Fan Regulator Fan step regulator, 120 Watt - two module etc complete all as specified and directed by Engineer-in-Charge

Supply & fixing lamp holder (Angular/Straight ), insulated body, with back plate for batten fitting etc complete all as specified and directed by Engineer-in-Charge

M&L for ceiling rose three terminal / PVC / polycarbonate, isolated body etc complete all as specified and directed by Engineer-in-Charge

S&F in replacement double door Sheet metal enclosures factory made DBs 4 way TPN, 415 volts Concealed in Wall,protection class IP-42, suitable for fixing of MCBs etc, confirming As per IEC 61439-3 ,Suitable for Flush Mounting and Surface Mounting, With 100 A Copper Busbar ,With Neutral bar, Earthbar and Cable ties for Cable management,Fully shrouded Neutral bars, Prefitted masking sheet complete all as specified and as directed. Make: Legrand ,Cat No:5076 70 or equivalent makes mentioned in list of makes in Appendix `C'

S & F in replacement double door Sheet metal enclosures factory made DBs SPN, 8 way ,240 volts ,protection class IP-42, suitable for fixing of MCBs,, confirming As per IEC 61439-3 ,Suitable for Flush Mounting and Surface Mounting, With 100 A Copper Busbar ,With Neutral bar, Earthbar and Cable ties for Cable management,Fully shrouded Neutral bars, Prefitted masking sheet etc complete all as specified and directed by Engineer-in-Charge. Make: Legrand ,Cat No: 5076 11 or equivalent makes mentioned in list of makes in Appendix `C'

Supply & fixing MCB , SP, AC, 240 Volts of 06 to 40 Amp capacity 16 KA, 'C' series and making connections with suitable size of copper lugs etc complete all as specified and directed by Engineer-in-Charge

Supply & fixing MCBs, TPN, AC, 415 volts of 63 Amps capacity 16 KA, 'C' series and making connections with suitable size of copper lugs etc complete all as specified and directed by Engineer-in-Charge

Supply & fixing MCBs, SPN, AC, 240 volts of 40 Amps capacity 16 KA, 'C' series and making connections with suitable size of copper lugs etc complete all as specified and directed by Engineer-in-Charge

Supply and fix Industrial type ultra slim square profile LED lighting fixture, environmental friendly, energy efficient ready to use pack Industrial type LED Tube light fitiing 20 Watt with LED light source 6500 K with uniform light output, with all accessories including its connection with and including 2 core sheathed copper conductor cable of size 0.5 Sqmm with complete with all accessories etc complete all as specified and directed by Engineer-in-Charge.

S&F Decorative ultra slim square profile LED lighting fixture with extruded polycarbonate, environmental friendly, energy efficient ready to use pack LED Tube light fitiing 10 Watt with LED light source 6500 K with uniform light output, with all accessories including its connection with 2 core seathed copper conductor cable of size 0.5 Sqmm with etc complete all as specified and directed by Engineer-in-Charge

Supply & fix in replacement energy saving and environmental friendly long life LED street light 25 Watt (Bldg security light) made up of pressure die cast aluminium housing with mild power LED as lighting source and PC cover having TOP Opening seperate driver compartment with IP65 protection and impact resistance of IK07 fixed on wall with GI pipe of suitable dia and all fixing accessories including connecting up with & including twin core twisted flexible copper conductor cable of suitable size of 230V , 50 HZ etc complete all as specified and directed by Engineer-in-Charge

S&F sub main wiring with two single core PVC insulated,unsheathed, FRLSH stranded copper conductor cable 6 Sqmm with 6 Sqmm PVC insulated, unsheathed, FRLSH stranded copper conductor cable as earth wire drawn through and including PVC Casing and capping ISI Marked with its all necessary accessories and earth wire connected to common earth dolly etc complete all as specified and directed by Engineer-in-Charge (Make of Cable : Finolex/RR Cable/Havells & Make for PVC Casing & Caping : AKG/PRESTOPLAST/PRECISION): - Note : 1. Porper colour coding shall be adopted for wiring (For Phase- Red, Yellow, Blue, For Earth - Green and For Neutral- Black) 2. Two run of 6 sq.mm cable i.e for one run for phase, one run for neutral with one run of 6 Sqmm cable for earth and one run of PVC Casing & caping shall be measured as one unit

Material & labour for earthing complete with galvanised steel earth plate electrode 600x600x6mm thick burried directly in ground. Earth pit not less than 2.25 m depth and top edge of the earth plate not less than 1.5 m below normal ground level connected to galvanised earth lead wire 4.0 mm dia by means of nuts, bolts & washer etc. Earth wire connected upto main earth point / DBs alongwith 15mm dia earth protection pipe from top edge of the earth plate to main earth point to be connected and 20mm dia watering pipe light grade with funnel and provn of PCC using cement concrete (1:2:4) mix type B1 using granded stone aggregate and RCC pit cover 50 mm thick precost RCC (1:2:4) mix type B1 duly reinforced with 8 mm dia of TMT bar @ 100 mm CIC, both way, lifting arrangement complete including all necessary earth work etc complete all as specified and directed by Engineer-in-Charge

M & L for Supply,laying ,connecting ,testing and commissioning and jointing , LT underground cable in replacement ,1100 volts grade, XLPE insulated, armored with galvanized round steel wire or steel strip, electric power cables heavy duty, with multi stranded aluminum conductor, laid in ducts, fixed on poles/walls with proper size saddles and clamp complete all as specified and as directed by the Engineer-in-Charge of following Sizes :-

(a) LT cable10 Sqmm, 4 core.

Supply &lay HDPE pipe 40 mm bore for laying of LT cable complete with all accessores etc complete all as specified and directed by Engineer-in-Charge

Taking out/down and opening of existing ceiling fans 1200 mm sweep,from any position, of any make etc & refixing at the desired location after reassembling and after servicing/overhauling by thouroghly cleaning the shaft,rotor,stator and applying lubricant/grease to bearings and one coat of super enamelled varnish over winding to improve the insulation resistance including repair /replacement of spare parts/ material /items , making connection by replacing PVC insulated unsheathed cable of copper conductor of size 1.50 Sqmm upto 0.50 Mtr length including using material/parts of minor nature such as screws, lugs, insulation tape, nuts, bolts, washers etc after cleaning the metal surface, greasing/lubricant etc to make it functional tc complete all as specified and directed by Engineer-in-Charge

Material and labour for preperation of ceiling fans 1200 mm sweep, of any make by cleaning of metal surfaces including painting with spray painting on required gloss with white synthetic enamel paint on complete body of fans and writing MES No with black synthetic enamel paint etc complete all as specified and directed by Engineer-in-Charge

An amount of Rs 53,029.00 shall be deducted from BOQ on account of schedule of credit

M/s. A P INFRA

OM SAI ASSOCIATES

M/s Meher Construction

MS. A.S. CONSTRUCTION

M/S-B.R.SONAWANE

M/s. Sagar Traders