PROVN OF OPEN TRAINING SHED WITH ELEVATED PLINTH (25Mx15M ALONGWITH 4 FT WALL) AND ALLIED FACILITIES IN 18 WEU UNDER GE SATWARI

Amount

Note :-Execution of work vide Srl item No 1 to 30 of BOQ shall strictly be followed as per Drg No CEPZ/STD-029/2001 sheet 1/2 and 2/2 for steel roof truss design purose and connected drgs referred vide Drg No GE SAT/WD-246/2022 provided for plan, all sides elivation and footing prupose. Tenderers are requested to compare items of BOQ to their estimat and any items found to be indvertantly left out in BOQ, be brought to the notice of this office timely for its inclusion in Tender documents. However cost of any of the items shown in Drg No GE SAT/WD-246/2022 but leftout indvertantly shall be deemed to be included in the quoted rates of other BOQ items.

Surface dressing not exc 15cm deep and getting out in any type of soil complete all as specified.

Excavating in trenches, not exc 1.5 m wide and not exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits,manholes, pier holes, etc. not exc 10 Sqmm on plan and n exc 1.5 m in depth and getting out in any type of soil, complete all as specified and as directed by Engineer-In-Charge.

Plain cement concrete 1:4:8, type D-2 (using 40mm graded crushed stone aggregate), as in subbase, mass concrete in foundation, complete all as specified and as directed by Engineer-In-Charge.

RCC (Design Mix) M-25 (using 20mm graded crushed stone aggregate) as in columns, pillars, piers, posts and struts etc complete all as specified and directed

Use and waste of formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter for rough finished surfaces complete all as specified and as directed by Engineer-In-Charge.

TMT bars 10 mm and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed by Engineer-In-Charge.

TMT bars 6mm to 8mm dia cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed by Engineer-In-Charge.

75 mm thickness PCC 1:4:8 type D-2 (Using 40 mm graded crushed stone aggregate) as in sub base complete all as specifieds and directed. by Engr-in-Charge

Chequered cement concrete tiles 30cm x 30cm x 20 mm thick, set, jointed and pointed in neat cement slurry in floors over and including 15mm thick screed bed with cement mortar 1:6 complete all as specified and directed by Engr-in-Charge.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25Cm, complete all as specified and directed by Engineer-In-Charge.

Removing excavated materials, to a distance not exceeding 50mtrs and depositing where directed at a level not exceeding 1.50mtrs,beyond the starting point complete all as specified and directed by Engineer-In-Charge.

Spreading and levelling in layers n exc. 25 cm thick,watering and well ramming in layers as in floors with earth obtained from excavation complete all as specified and directed by Engineer-In-Charge.

Hardcore of broken stone of gauge not exc 63mm, deposited spread and leveled in layers not exc 15cm thick watered and well rammed to a true surface, complete all as specified and directed

40 mm thick PCC 1:2:4 type B-0 (using 20 mm graded crushed stone aggregat) as in floor finished rough complete all as specifieds and directed.

PCC 1:2:4 type B 1 using (20 mm graded crushed stone aggregate) as in blocks for hold fasts, benching, coping apex stones, bed plates and the like including weathering slightly rounded or chamfered angles and throating all as specified and direct. Note: Form work required for these items included in the unit rate of this item complete all as specifieds and directed.

Brick work in cement mortar 1:6 using sub-class B bricks straight or curved on plan exc 6m mean radius complete all as specifieds and directed.

Rendering 15 mm thick in cement mortatr 1:4 on fair face of brick work surfaces finished even and smooth without using extra cement complete all as specifieds and directed.

Rendering 15 mm thick in cement mortar 1:6 on other than fair face of brick work/ stone wall surfaces finished even and smooth without using extra cement all as specified. complete all as specifieds and directed.

Plain cement concrete 1:3:6, type C-1 (using 20mm graded crushed stone aggregate), 50 mm thick, as in plinth protection and providing the joints throughout the thickness, filled with mastic filling comprising bitumen 85/25 grade and sand mixture 1:3 by weight, complete all as specified and as directed by Engineer-In-Charge.

Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240 complete all as specifieds and directed.

Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel, gusset plates, or flat sections) including distance pieces, cleats etcFe 410 -W (GdeE- 250) qualityA complete all as specifieds and directed.

Rolled mild steel Plates (plain or chequered) square cut or notched (ordinary and counter sunk) forming holes etc of Fe-410-W(Gde E-250) quality B complete all as specifieds and directed.

Pre- painted galvatume aluminum zinc coating (AZ-150 Micron) GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specifieds and directed.

Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick ( AZ-150 Micron) of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specifieds and directed.

Mild steel screw bolt (machine made) dia 16 to 20 mm with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, but length of bolt exc 22.5cm and n exc 30cm long complete all as specifieds and directed.

Machine cut kota stone slab flooring 18-20 mm thick over cement screed bed laid and jointed cement screed bed laidand jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing complete over and including 15mm thick screed bed in cement mortar 1:4 all as specifid and directed

Machine cut kota stone slab 18-20 mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing complete for risers of staircase over and including 10mm thick fair and even plaster in cement mortar 1:4 after roughing surfaces of old concrete/any type of plaster by picking sweeping down with water to remove dust etc. complete all as specifieds and directed.

Preparation of newly plastered surfaces of walls, & applying two coats of oil bound distemper over two coat of wall care putty of 1 to 2 mm thick and one coat of primer complete all as specifieds and directed.

Preparation of newly plastered/concrete surfaces of walls and applying two coat of cement based paint over one coat of primer complete all as per specified and directed by Engr-in-charge.

Two coats of synthetic enamel paint over a coat of red oxide primer on new steel surfaces including preparation of surfaces over 10cm width or girth complete all as specifieds and directed. by Engr-in-Charge

Point wiring complete with 1.5 Sqmm single core PVC insulated and unsheathed cable 1100 volts FRLSH grade with multistranded copper conductor ISI market drawn throught heavy duty PVC concealed conduit fixed to wall / roofs / floors / ceiling etc and including provision of 1.5 Sqmm standed copper conductor cable as earth continuity conductor and connected to common earth dolly including concealed MS box with 3 mm thick laminated sheet cover fixed with brass screws and cup washers for mounting of plate mounting for housing the switches, socet outlets, fan regulators etc complete all as specified and as directed for the following:-

(a) One 3 pin socket outlet 6 amp on independent board complete all as specified and as directed.

(b) One 3 pin socket outlet 6 amp on same board with other switches complete all as specified and as directed.

All as per description of srl item No 31 above but for one 3 pin socket outlet 16 Amp on independent board with cable of size 2.5 Sqmm for point wiring and 2.5 sqmm as in continuous earth wire complete all as specified and directed.

Switch piano, flush type single pole, one way 6 amps capacity complete all as specified and as directed.

Socket out let 2 in 1 , 5 Pin 6A combined 2 module complete all as specified and as directed.

Switch piano, flush type single pole, one way 16 Amps capacity complete all as specified and as directed.

Socket out let 2 in 1 , 5 Pin 16A combined 2 module complete all as specified and as directed.

Distribution board (SPN) double door 8 way and should be IP 43 protected with copper bus bar 100 amp rated Earth Bar , neutral bar door earthing complete all as specified and as directed.

MCB SPN 32 Amp 240 Volts rupturing capacity 10 KA 'C' series, complete all as specified and directed.

MCB single pole 6 to 32 Amp 240 Volts, rupturing capacity 10 KA 'C' series, complete all as specified and directed

Galvanised mild steel earth plate electrode of size 600x600x6mm thick burried directly in ground earth pit not less than 2.25 mtr deep below normal gound level with top edge of the earth plate not less than 1,5 mtr below ground level connected to galvansed iron or earth lead wire 4mm dia (8SWG) by meant of nut bolt check nuts and washer of galvanised iron including PCC pit in PCC 1:2:4 type B-1 pre-cast RCC cover slab using reinfocement with XPM weighing not less than 1.87 kg/Sqmm with suitable handle made of 12mm round bar including necessary excavation and earth work inany type of soil 20mm dia medium grade galvanised steel tube for watering with one end fixed with cast iron funnel and wire mesh 15mm dia bore light grade galvanised steel tubing upto 7.5 m length for drawing earth lead wire protection common salt, charcoal etc shown in electrical plate No 3 of SSR part-1 and testing on complete all as specifieds and directed.

Sub main wiring with single core cable 2 x 4 Sqmm FRLSH insulated Unsheathed stranded copper conductor cable 1100 Volts grade in rigid PVC conduit (Concealed) medium grade alongwith 1 x 4 Sqmm FRLSH insulated unsheathed copper conductor cable as earth wire connected with main earth dolly complete all as specifieds and directed.

LED flood light 70 Watt 230 Volt AC outer type with thermal management in multiple optpics and equipped with IP 66 protection with impact and corrosion resistant complete with fixing arrengenment including clamps any type and size, nuts, bolts, washer and fixing on chanels, floor, poles et c and with driver and lamps complete all as specified directed.

25 mm dia rigid non-metalic PVC conduit medium grade ISI market in wall/ceiling/roof/trusses/angle of boxes (junction/terminal) tees, bends, elbows, reducers, bell mouth, tube ends and fixing by clamps with accessories such as couplers, lock nuts, saddles, pipe hooks etc complete all as specified directed.

Ceilling fan complete with blade, down road, and accessories, 230 V, 1200 mm sweep, Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current mortar (BLDC) and connected from ceilling rose/connector with & including suitable size flexible copper conductor PVC insulated sheathed cord, complete all as specified directed.

Replacement of unserviciable underground LT cable 1100 Volts grade heavy duty electric cable XLPE insulated & PVC outer sheathing with aluminium stranded conductor, Armoured cable 25 Sqmm 2 core cable confirming to IS-7098 Part-I (1988) with latest ammendments of sizes,. complete all as specified directed.

Cutting of bituminous road/ floor/ culvert/ PCC hard standing for laying of pipe / cable not exceeding 1.5 mtr wide and not exceeding 1.5 mtr deep encluding refilling/ with material watering and well ramming/ compacting and making good with PCC 1:2:4,type B-1(using 20mm graded crushed stone aggregated) 100 mm thick. complete all as specifieds and directed.

Dry river sand as cable cushioning 15cm thick layer before laying and 8cm thick over cable after laying the cable in trench complete all as specifieds and directed.

Dry bricks over cable as mechanical protection layed flat with width equal to length of brick with sub class 'B' bricks complete all as specifieds and directed.

GI pipe ''light grade'' for road crossing / on wall / on pole with fixed clamps, nuts, bolts for cable protection of size 40 mm dia complete all as specifieds and directed.

Srl item No 49 Contd … GI pipe ''light grade'' for road crossing / on wall / on pole with fixed clamps, nuts, bolts for cable protection of size 40 mm dia complete all as specifieds and directed.

STAR CONSTRUCTIONS

J P TECHNO

NARESH KUMAR AND COMPANY

M/S ANIL MAHAJAN

M/S ARUN ANAND