Provision of Wash Room for Office of Chairperson P.U. ISSER Department at Panjab University Campus, Sector-14, Chandigarh.

Civil Work

Disposal of moorum/building rubbish/ malba/ similar unserviceable, dismantled or waste material by mechanical transport including loading, transporting, unloading to approved municipal dumping ground for lead upto 10 km for all lifts, complete as per directions of Engineer-in-charge. (Ref:- 1.1.18)

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge.

All kinds of soil (Ref:- 2.6.1)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :

1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) (Ref:- 4.1.3)

12mm cement plaster of mix

1:6 (1cement :6 fine sand) (Ref:-13.1.2)

Distempering with oil bound washable distemper of approved brand and manufacture to given an even shade

New work (two or more coats) over and including water thinnable priming coat with cement primer. (Ref:-13.41.1)

Demolishing cement concrete manually/ by mechanical means including disposal of material with in 50 metres lead as per direction of Engineer in charge..

1:4:8 or leaner mix (Ref:-15.2.2)

Demolishing brick work manually / by mechincal means including stacking of serviceable material and disposal of unserviceable material with in 50 metres lead as per direction of Engineer In -Charge.

In Cement Mortar (Ref:-15.7.4)

Dismantling stone slab flooring laid in cement mortar including stacking of servicable material and disposal of unserviceable material with in 50 metre lead. (Ref:-15.25)

Dismantling precast concrete or stone slabs in walls, partition walls etc. including stacking within 50 metres lead:

Thickness upto 40 mm (Ref:-15.40.1)

Dismantling G.I. pipes (external work) including excavation and refilling trenches after taking out the pipes, manually/ by mechanical means including stacking of pipes within 50 metres lead as per direction of Engineer-in-charge :

15 mm to 40 mm nominal bore (Ref:-15.44.1)

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. (Ref:-15.56)

Providing And Fixing white vitreous chinaware pedestal type water closet (European type W.C.pan ) with seat and lid, 10 litre low level white P.V.C flushing cistern with manually controlled device ( handle lever), conforming to IS: 7231, with all fittings and fixtures complete including cuting and making good the walls and floors wherever required:

W.C. pan with ISI marked white solid plastic seat and lid (Ref:-17.2.1)

Providing and fixing toilet paper holder:

C.P. Brass (Ref:-17.34.1)

Providing and fixing soil, waste and vent pipes

100 mm dia.

Sand cast iron S& S pipe as per IS: 3989 (Ref:-17.35.1.2)

Providing and fixing soil, waste and vent pipes

75 mm dia.

Sand cast iron S& S pipe as per IS: 3989 (Ref:-17.35.2.2)

Providing and fixing collar:

sand cast iron S&S as per IS-3989 (Ref:-17.57.1.2)

Providing and fixing collar:

sand cast iron S&S as per IS-3989 (Ref:-17.57.2.2)

Providing lead caulked joints to sand cast iron/centrifugally cast (spun) iron pipes and fittings of diameter:

100mm (Ref:-17.58.1)

Providing lead caulked joints to sand cast iron/centrifugally cast (spun) iron pipes and fittings of diameter:

75mm (Ref:-17.58.2)

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors :

100mm inlet and 75mm outlet

Sand cast iron S& S as per IS-3989 (Ref:-17.60.2.1)

Providing and fixing G.I. Pipes complete with G.I. fittings and clamps, i/c making good the walls etc. concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall :

15 mm dia nominal bore (Ref:-18.11.1)

Providing and fixing G.I. Pipes complete with G.I. fittings and clamps, i/c making good the walls etc. concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall :

20 mm dia nominal bore (Ref:-18.11.2)

Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc.complete:

Wash Room/ for chairperson GF (Ref:-18.13.1)

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :

20 mm nominal bore (Ref:-18.17.1A)

Providing and fixing uplasticised PVC connection pipe with brass C.P. Nuts collar and bush of approved quality colour.

45cm length

15 mm nominal bore (Ref:-18.21.2.1)

Providing and fixing G.I. Union in existing G.I. pipe line,cutting and threading the pipe and making long screws inclding excavation, refilling the earth or cutting of wall and making good the same complete wherever required:

15 mm nominal bore (Ref:-18.47.1)

Providing and fixing G.I. Union in existing G.I. pipe line,cutting and threading the pipe and making long screws inclding excavation, refilling the earth or cutting of wall and making good the same complete wherever required:

20 mm nominal bore. (Ref:-18.47.2)

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 (Ref:-18.52)

Providing and fixing C.P. brass stop cock (concealed) with caps including SS flange. Complete in all respect to the entire satisfaction of the engineer in-charge.

15 mm nominal bore(Ref:-18.52.1)

Cutting holes upto 30x30 cm in walls including making good the same:

With F.P.S. bricks. (Ref:-18.76.1)

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :

For fixed portion

Powder coated aluminium (minimum thickness of powder coating 50 micron) 10 Gauge (Ref:-21.1.1.2)

Providing & laying P.C.C. 1:8:16 (1 Cement : 8 coarse sand: 16 coarse aggregate)with stone ballast 32mm guage in foundation and plinth. Complete in all respect to the entire satisfaction of the Engineer-in-charge. (Ref:-N.S.)

Providing & Laying Half Brick masonry work with F.P.S. bricks of class designation 100 in superstructure above plinth level upto floor V level. complete in all respect to the satisfaction of the engineer in charge.

Cement mortar 1:4 (1 cement :4 coarse sand) (Ref:-N.S.)

Providing and laying Brick work with F.P.S. bricks of class designation 100 (average compressive strength not less than 105 kg per sq.cm.) in Foundation and plinth in :

Cement mortar 1:6(1 cement : 6 coarse sand) (Ref:-N.S.)

Providing and laying Brick work with F.P.S. bricks of class designation 100 (average compressive strength not less than 105 kg per sq.cm.) in superstructure above plinth level up to floor V level in all shapes and sizes in :

Cement mortar 1:6 (1 cement : 6 coarse sand) (Ref:-N.S.)

Providing and fixing 32mm dia G.I. waste pipe along with elbow or bend. complete in all respect to the entire satisfaction of the engineer-in-charge. (Ref:-N.S.)

Providing and fixing 1st quality ceramic glazed wall tiles (300x600mm) conforming to IS: 15622 of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. (Ref:-N.S.)

Providing and laying Anti skid floor tiles of size 300x300mm of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), including pointing the joints with white cement and matching pigment etc., complete. (Ref:-N.S.)

Providing and fixing 15mm C.P. brass Angle cock and SS flange of approved quality. complete in all respect to the entire satisfaction of the engineer-in-charge. :

15 mm nominal bore (Ref:-N.S.)

Providing and fixing in position 15mm dia CP Brass nipple(1" to 2" long) to various fittings. Complete in all respect to the entire satisfaction of the engineer-in-charge. (Ref:-N.S.)

Providing and fixing Single socketed on wall face unplasticised Rigid UPVC pipe (6 kg per Sqcm pressure) of size 100mm dia conforming to IS : 13592 Type A, including jointing with necessary Tee and Bend conforming to IS : 5382, leaving 10 mm gap for thermal expansion. complete as per entire satisfaction of the Engineer-in-Charge.

100mm dia (Ref:-N.S.)

Providing and fixing C.P. towel Ring complete with PVC rawl plug and CP Brass screws with concealed fittings of approved quality and colour.Complete in all respect to the entire satisfaction of the engineer-in-charge (Ref:-N.S.)

Providing and fixing 3mm thick bakelite sheet of approved brand by engineer-in-charge at site. The sheet is to be used in panelling work for aluminium door/winow/shutter and partition fixed in position with C.P. brass screw or EPDM gasket etc. Complete in all respect to the entire satisfaction of the engineer-in-charge. (Ref:-N.S.)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): (Ref:-N.S.)

Providing & fixing Liquid Soap dispenser with metallic bottle. Complete in all respects as per entire satisfaction of the Engineer-in-Charge. (Ref:-N.S.)

Providing and fixing Jet connection alongwith 450mm long pipe for water closet. Complete in all respect to the entire satisfaction of the engineer-in-charge. (Ref:-N.S.)

Providing and fixing C.P. Stainless steel fitting heavy duty ISI marked.

Tower bolt 8" long (Ref:-N.S.)

Providing and fixing C.P. Stainless steel fitting heavy duty ISI marked.

Tower bolt 6" long (Ref:-N.S.)

Providing and fixing C.P. Stainless steel fitting heavy duty ISI marked.

Handle 5" D-type (Ref:-N.S.)

Providing and fixing C.P. Stainless steel fitting heavy duty ISI marked.

Hinges 5" (Ref:-N.S.)

Providing and fixing Hydraulic door closer with logo printed along with necessary fittings. Complete in all respect to the entire satisfaction of the engineer in charge. (Ref:-N.S.)

Providing & making 6mm thick looking mirror to be fixed on 6mm thick BWP(water proof) ply along with 2"x1" Teak wood beading duly polished. Complete in all respects to the entire satisfaction of the engineer in-charge. (Ref:-N.S.)

Please Enable Macros to View BoQ information