8226 REPAIRS TO ROOF, PLUMBING, JOINERY, FLOORING, PLASTERING, PATH AND CONNECTED ITEMS TO CERTAIN BLDG AT MINTSD MD AND OTM ACCN AND AREA UNDER AGE BR II SOUTH PUNE

Amount

Dismantling stone slab/tiles of any description or thickness, laid, bedded & pointed in cement mortor in floors, hard standing, Apron etc complete all as specified and as directed.

Demolition of cement concrete in ground floors and paving not exc 15cm thick (below or above ground level incl sunken slab) un-reinforced complete all as specified and as directed.

Demolition of brick/precast block walling built in cement mortar complete all as specified and as directed.

Taking down cement plaster on brick/ block walling including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and as directed.

M&L for 75mm thick PCC (1:4:8) type D-2 (using 40mm graded stone aggregate) as in sub base / flooring complete all as specified and as directed.

M&L for PCC 1:3:6 type C-2, (using 40mm graded stone aggregate), 75mm thick, laid in alternate bays including finishing the surfaces even and smooth using extra cement complete all as specified and as directed.

M&L for hardcore of broken stone or boulder n.exc. 63mm gauge, deposited, spread, levelled and well rammed including watering to a true surface complete all as specified and as directed.

M&L for PCC 1:2:4 type B-1 (using 20mm graded stone aggregate), 40mm thick, finished surface even and without smooth using extra cement complete all as specified and as directed.

S&F glass dividing strips 3 mm thick and 38 mm wide inserted in position as dividing strip in flooring complete all as specified and as directed.

M & L for 25mm thick cement concrete 1:2:4 type B-0 (using 12.5mm graded stone aggregate) as in floor levelling course complete all as specified and as directed.

M&L for 400x400x 6 to 7mm thick, non skid, ceramic, coloured tiles, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match complete over and including 15mm thick screed bed in CM 1:6 complete all as specified and as directed.

M&L for 300x600x5.5 to 6mm thick, coloured, glazed ceramic tiles as in skirting/Dado, laid and jointed in neat cement slurry and pointed in coloured cement to match complete over and including 10mm thick backing coat in CM 1:4 including triangular filleting on top in CM 1:4 complete all as specified and directed.

M&L for coloured vitrified tiles 600 x 600 x 8 mm thick as in flooring, set and jointed in neat cement slurry and pointed in coloured cement to match with tiles, laid over and including 20mm thick screed bed in CM (1:6) complete all as specified and as directed.

M&L for coloured vitrified tiles 600 x 600 x 8 mm as in skirting/dados, set and jointed in neat cement slurry and pointed in coloured cement to match with tiles, laid over and including 10mm thick backing coat in CM (1:4) including triangular filleting in CM 1:4 on top of tiles complete all as specified and as directed.

M&L for hand cut Kota stone flooring 20 to 25 mm thick laid, jointed with grey cement slurry and pointed with coloured cement to match the shade of Kota stone as in floor, treads etc including rubbing and mirror polishing laid over and including screed bed 20mm thick in CM 1:6 complete all as specified and directed.

M&L for hand cut kota stone 18 to 20mm thick as in skirting /Dado, set and jointed in neat cement slurry and pointed in coloured cement to match the shade of kota stone slab including, rubbing and mirror polishing laid over and including 10mm thick backing coat in CM 1:4 complete all as specified and as directed.

M&L for 18 to 20 mm thick, 75mm wide, marble strip, of approved colour, set & jointed in grey cement slurry and pointed in white/ coloured cement to match the shade of marble, laid over & including 20 mm thick, screed bed in CM 1:6 including rubbing and polishing complete as in floors complete all as specified and as directed.

S & F Machine cut cuddappa stone slab one side polished 20 to 25mm thick, set and jointed in neat cement slurry and pointed in coloured cement to match, laid over and including 20mm screed bed in cement mortar (1:6) complete all as specified and as directed.

M&L for Granite 20mm thick (of any type) work, (table rubbed and polished) as in WHB platform and like set in CM (1:4) including pointing in white cement (1:2) using Marble dust with admixture of pigment to match with the shade of the Granite complete all as specified and as directed.

M&L for coloured precast chequered cement concrete tiles, glossy finish of size 400x400mm & 35mm thick, set jointed and pointed in neat cement slurry in floor laid over and including 20mm thick screed bed in CM (1:6) complete all as specified and as directed.

M & L for precast concrete interlocking paver blocks glossy finish with any shape and size conforming to IS-15658-2006, 60mm thick, M-35 grade with grey cement and pigment laid over & including 75mm thick stone dust/grit complete all as specified and as directed.

M & L for solid block masonary exc. 10 cm width blocks of PCC design mix Gde C-5 set in CM (1:6) complete all as specified & directed.

M&L for dubbing out average 15mm thick in CM 1:6 on irregular faces of walls (When specifically ordered in writing) complete all as specified and as directed.

Rendering (as subsequent coat) 10mm thick over dubbed out surfaces/concrete/brick surfaces in CM 1:6 finished event & smooth with sagol finish complete all as specified and as directed.

Rendering 10mm thick (as subsequent coat) in CM (1:4) over dubbing out surfaces using water proofing compound as per manufacturers instruction finished with sponge finish complete all as specified and as directed. (NOTE : WPC shall be measured and paid seperately)

Rendering 15mm thick in cement mortar 1:4 on brick/concrete surfaces using water proofing compound as per manufacturers instructions surface finished with sponge finish. (upto G+2 storey) (Note 1 : WPC shall be measured and paid separately)

S & F MS TMT bars 10mm dia and over, cut to length, bent to shape reqd, including cranking, bending spirally for hooping for columns and binding with mild steel annealed wire of dia not less than 0.9 mm or securing with clips complete all as specified and as directed.

Taking up or down carefully steel tubing and connections including cleaning for refixing of size 15mm bore complete all as specified and as directed.

Taking up or down carefully steel tubing and connections including cleaning for refixing of size 20mm bore complete all as specified and as directed.

Taking up or down carefully steel tubing and connections including cleaning for refixing of size 25mm bore complete all as specified and as directed.

M & L for 15 mm bore GI tubing medium grade with all fitting and fixed complete on walls and ceilings or laid in floors etc complete all as specified and directed.

All as per item No. 31.00 above but fixing only complete all as specified and as directed.

M & L for 20 mm bore GI tubing medium grade with all fitting and fixed complete on walls and ceilings or laid in floors etc complete all as specified and directed.

All as per item No. 33.00 above but fixing only complete all as specified and as directed.

M & L for 25 mm bore GI tubing medium grade with all fitting and fixed complete on walls and ceilings or laid in floors etc complete all as specified and directed.

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc, and cutting chses for concealed water tubing or concealed conduit wiring, etc complete all as specified and as directed.

S&F in repairs vitreous china wash down water closet pan, 'Pedestal' coloured, including fixing bolts etc including PVC seat cover white with flat bottom including MS, CP or aluminium anodised hinges devices including PVC low level flushing cistern 10 Ltr capacity with all internal fitting, inlet, outlet pipe connections etc. complete all as specified and directed.

S&F in repairs vitreous china, squatting pan, 'Orissa' pattern, size 580 x 440mm white, with integral foot rest, including concrete bedding and PVC flushing cistern 10 Ltr capacity including all internal fitting, inlet, outlet pipe connections etc. complete all as specified and directed.

S&F in repair vitreous china wash hand basin, white, 550x 400mm flat back including providing CI brackets, PVC waste pipe 32mm dia, waste coupling 32mm bore of CP and longbody CP pillar tap etc all as specified and directed.

S&F in repair vitreous china ovel type wash hand basin, including providing PVC waste pipe 32mm dia, waste coupling 32mm bore of CP and CP longbody pillar tap all as specified and directed.

S&F 20mm bore ‘D’ type brass CP tubular towel rail 60 cm long between flanges complete fixed in repairs complete all as specified and as directed.

S & F vitreous china bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum) with grating and union for discharge pipe complete all as specified and as directed.

S&F in repairs salt glazed stone ware gully traps, square 150x150mm size complete all as specified and as directed.

S&F stainless steel, sink with drainboard 1 mm thick for kitchen, with plug, waste pipe, washers incl cantilever CI Brackets, connecting union etc & connecting to inlet/out let for smooth functioning size of sink 915 x 460 mm overall and bowl size 410mmx355mmx165mm complete all as specified and as directed.

S&F in repairs stainless steel sink 1.00 thick for kitchen or laboratory with plug waste pipe washers including cantilivers cast iron brackets connecting union etc over all size 495mmx420mm with bowl size 410mm x 330mm x 160mm complete all as specified and as directed.

M&L for providing and fixing CP toilet fitting in repairs as specified and as directed by the Engr -in-Charge for the following:-.

Brass CP wall mixer Non-telephonic shower arrangement screwed down for iron pipe of bore 15mm of make 'METRO'.

15mm bore bib taps, brass chromium plated, cast copper alloy fancy type handle, screwed down, screwed for iron pipes fixed in repairs.

Brass CP toilet paper holder.

Brass CP towel ring.

CP pressure adjustable shower with revolving joint.

Stop valve brass chromium plated, fancy type with long shank and cup (concealed type) fixed to pipe of 15mm bore.

Soap dish, brass chromium plated.

Health faucet CP

Urinal spreader brass chromium plated

S&F in repair bib cock 15mm bore standard of PTMT screwed down high pressure handle screwed for iron pipe or for unions complete all as specified and as directed.

S&F in repair fancy type pillar taps 15mm bore cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed for iron pipe etc complete all as specified and as directed.

S&F stainless steel grating 75 to 100 mm dia suitable for nahani trap complete all as specified and as directed.

Supply and fix in repairs, Gun metal, Globe or gate valves with iron wheel head, screwed both ends for iron pipes of size:-

20mm bore

25 mm bore

Supply and fix, in repairs, ball valves high pressure, of PTMT with epoxy coated Aluminium rod and high density plastic ball screwed for iron pipe (Minimum weight 20mm-210gms/25mm-455gms / 40mm-690gms) for the following :- (Make - Prayag/Symet or of equivalent make)

15 mm bore

20mm bore

25 mm bore

Supply and fix in replacement of PVC connection 15mm bore suitable for Hot or cold water, heavy duty, of size 60 cm long complete all as specified and as directed.

Disconnecting of existing water tanks, setting aside (or lowering,if required) for repairs,cleaning etc and hoisting if required reconnection and re-fixing in position. (Cleaning, reparing etc. measured separately) capacity upto 2000 ltrs complete all as specified and as directed. (NOTE : Necessary by pass arrangements for water supply is to be done by the contractor till the completion of roof work)

M & L for Cleaning and removing all dirt and scale etc from tank and from the mouths of circulating pipes for the tanks of capacity upto 2000 litres complete all as specified and as directed.

Dismantling of PVC water tanks exc 500ltr and n.exc 1000 ltr capacity removing to store complete all as specified and directed.

Dismantling of PVC water tanks exc 1000ltr and n.exc 2000 ltr capacity removing to store complete all as specified and directed.

S&F rotational moulded polyethylene water storage tank 500 Litres capacity ISI marked (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Pt-I with 25 mm ball valve high pressure PTMT with rod & high density plastic ball complete all as specified and directed.

S&F rotational moulded polyethylene water storage tank of 1000 ltr capacity ISI marked (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Pt-I with 25 mm ball valve high pressure PTMT with rod & high density plastic ball complete all as specified and directed.

S&F rotational moulded polyethylene water storage tank of 2000 ltr capacity ISI marked (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Pt-I with 25 mm ball valve high pressure PTMT with rod & high density plastic ball complete all as specified and directed.

S&F, in repairs, PVC cover for water storage tank of 300litres/ 500 litres Capacity fixed with PVC locking arrangements all complete all as specified and as directed.

Dismantling of drain pipes AC /CI/PVC pipes of various dia jointed in CM or adhesive 75 to 110mm dia complete all as specified and as directed.

S&F PVC (SWR) pipes, single socketed in any length with rubber ring joints laid in trenches or fixed to wall of following size :-

110mm bore

75mm bore

S&F in repair PVC (SWR) bends any radius 110 mm bore complete all as specified and as directed.

S&F in repair PVC (SWR) bends any radius 75 mm bore complete all as specified and as directed.

S&F in repair PVC (SWR) bends any radius 110 mm bore provided with access door complete all as specified and as directed.

S&F in repair PVC (SWR) bends any radius 75 mm bore provided with access door complete all as specified and as directed.

S&F PVC (SWR) junction, (Single Tee) equal or unequal 110mm bore complete all as specified and as directed.

S&F PVC (SWR) junction, (Single Tee) equal or unequal 75mm bore complete all as specified and as directed.

S&F PVC (SWR) vent cowl 110 mm bore complete all as specified and as directed.

S&F PVC (SWR) vent cowl 75 mm bore complete all as specified and as directed.

M & L for PVC (SWR) floor trap, dia of outlet 75mm, plain with grating including jointing with solvent cement complete all as specified and as directed.

S&F in repair PVC low level flushing cistern 10 ltrs capacity make ISI or equivalent incl all internal fitting, pair of bracket, including inlet/outlet PVC pipe connections etc complete all as specified and as directed.

Preparation of new plastered surfaces and applying two coats of cement base paint complete all as specified and as directed.

Preparing newly plastered surfaces, including chalk whiting preparatory to distempering and applying two coats of oil bound distemper on walls over a coat of alkali resistance primer complete all as specified and as directed.

M&L for preparation of new steel surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed.

M&L for preparation of new wooden surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed.

S&F in repairs high density polythene pipe 40mm dia (HDPE) of pressure rating 6kgf/cm² fixed complete to wall or floor incl bend tee elbow etc. complete all as specified and as directed.

S&F brass CP, Jet Spray assembly complete all as specified and as directed.

S & F in repairs 32mm bore PVC waste pipe for urinal / WHB / Kitchen or laboratory sink complete all as specified and as directed.

Supply only integral water proofing compound complete all as specified and as directed.

Application of one coat of polymer based liquid water proofing compound on concrete surface (in sunken portion) after a coat of rendering as per manufacturers instructions complete all as specified and as directed. (NOTE :- Polymer based liquid water roofing compound will be measured and paid seperately.) (Make : SBR of Pidilite, Fosroc, STP or equivalent.)

Supply only polymer based liquid water proofing compound complete all as specified and as directed. (Make : SBR of Pidilite, Fosroc, STP or equivalent.)

M & L for PCC 1:5:10 type E-2 (using 40mm graded brick aggregate) lean concrete for filling sunken floor complete all as specified and as directed.

Laying APP polymer modified approved membrane non woven, polyster weighing not less than 3.5 Kg/Sqm with laps and overlaps as specified and joints sealed and applied complete by torch application method all as specified and directed by Engineer-in-Charge. Carrying out test by flooding water for 24 hrs for leakage and seepage and rectifying the same to the entire satisfaction of GE.

S&F solid PVC door frame of size 50mm x47mm made out of 5mm plain colour PVC sheet reinforced with MS tube , supplying and fixing in opening complete all as per specification and as directed.

S&F factory made solid panel PVC door shutter 30mm thick (stiles) consisting of frame made out of M.S tubes for top & bottom rails; M.S frame shall be covered with heat moulded plain colour PVC ‘C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail & bottom rail; panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification and drawing as per product Drg given on Sl. Page No. 156 of SSR Part-II 2010 Refer item No. 8080 as specified and directed.

S&F aluminium handles, anodised, cast type, of size 125 mm complete all as specified and as directed.

S&F aluminium anodised barrel tower bolts of extruded section 200 mm long complete all as specified and as directed.

S & F butt hinges 100mm size MS cold rolled medium weight complete all as specified and as directed.

S&F in repair 18 mm thick prelaminated particle board exterior grade, Conforming to IS-12823, Gde-I, prelaminated both side with decorative choice lamination as in Kitchen Cabinet etc fixed with screw including 3mm thick, 1st Class HW (TW) beading all around on edging to timber frame work all as specified and directed.

S & F in repair 30mm width of flap brass continious (piano) hinges for built in cup board shutter as approved complete all as specified and as directed.

S & F for standard telephonic slider for sliding drawer etc complete all as specified and as directed.

S&F 125 mm dia cupboard handles fixed with nuts, screws and washer of brass polished complete all as specified and as directed.

S&F ball catches with 8 mm dia steel ball, and brass body and striking plate including letting in and fixed complete all as specified and as directed.

Dismantling boarding/ceiling of any description, fixed in any position like partition etc with nails including frame work of timber complete all as specified and as directed.

M&L for Gypsum ceiling board for ceiling prepainted, perforated finish, 600 x 600 x 9 to 9.5mm thick in size, of approved brand/make, laid over and including grid work of size 600 x 600mm, made out of 0.5mm thick G.I. tee 32 x 24 mm for main, 25x24mm for cross tee and 20 x 20mm angle fixed on wall, powder coated finish on exposed faces of tee and angle. hung from ceiling using 2 mm thick G.I. Suspension wires spaced at 1200 mm on main runners including making niches for fans/light at as specified and directed.

S & F in repairs stainless steel wire cloth 0.56 mm nominal dia of wire and average width of aparture 1.18mm etc complete all as specified and directed.

Hacking out old broken glass (any thickness, size , quality or description) from metal frames , glazed with putty of fixed with beads as specified and directed.

S&F sheet glass ordinary quality, 3mm thick and glazing with oil putty in square n.exc. 0.5 Sqm in each pane complete all as specified and as directed.

S&F floor door stopper, aluminium alloy body and tongue anodised with hard drawn steel spring of 140mm size overall complete all as specified and as directed.

S&F aluminium powder coated fancy type curtain rod 25mm bore complete all as specified and as directed.

S&F aluminium powder coated brackets suitable for 25mm bore curtain rod (minimum projection from wall 75mm) fixed in wall including drilling, rawl plug, screws etc complete all as specified and directed.

Dismentling wrought rion or mild steel iron of any description not otherwise provide for.

Dismantling of plain or corrugated, steel sheeting, any gauge, thickness complete all as specified and as directed.

Dismantling of AC sheet corrugated, or semi corrugated in roof covering complete all as specified and as directed.

M & L 6mm thick non asbestos cement, corrugated or semi corrugated sheets in roof walls fixed with 'L' type or 'J' type or cranked hook bolts, washer etc complete all as specified and as directed.

M & L for asbestos cement two piece adjustable ridge 6mm thick fixed with L or J bolts with washer etc. complete all as specified and as directed.

M&L for MS structural steel work, framed as in trusses, purlins, rafter, post etc. conforming to grade E-250 (Fe-410W, quality A) including shaped washers including necessary cutting required length, notching drilling, riveting and or welding or connecting with nut bolts with angle cleats, fish plat, gusset plate and also erecting in true position complete all as specified and as directed.

S & F roof sheeting zinc coating GI based corrugated steel sheet 0.63mm thick of an colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified and as directed.

S & F Plain, galvanised, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings with grade of zinc coating 275 in any length and position, shape and size as including filletting at both the sides in cement mortar 1:3 complete all as specified and as directed.

S&F for galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering ,fixed with self taping screws complete all as specified and as directed.

Taking down chowkats or frames of wooden / steel n.exc 1.5 sqm (without taking off shutters from the frames) & removing from site incl cutting out hold fasts and making good to distrubed portion complete all as specified and as directed.

Taking down chowkats or frames of wooden / steel exc 1.5 sqm & n.exc. 4 Sqm (without taking off shutters from the frames) & removing from site incl cutting out hold fasts and making good to distrubed portion complete all as specified and as directed.

Taking down shutters of any description exc 1 sqm and n exc 2 Sqm each complete all as specified and as directed.

Taking down shutters of any description exc 2 sqm and not exc 4 sqm each complete all as specified and as directed.

Taking down and refixing of door exc 1 Sqm and not exc 2 Sqm in the same opening after easing and adjusting and planning if required complete all as specified and as directed.

S & F pressed steel frames for doors with one or more rebates incl necessary fixing lugs, hinges, lock strike plate etc complete as specified size of frame 105mm x 60mm filled with PCC 1:3:6 type C-0 complete all as specified and as directed.

S & F 35mm thick factory made, panelled shutter (two panel) with lock rail and panel of 9mm BWP commercial ply or 12mm veneer particle board with commercial veneering on both faces. The size of the rail and as per IS 1003 (Part-I) Kiln seasoned and chemically pressure treated as specified and directed.

S & F 35mm thick glazed and skeleton shutter open rebated and prepared to receive glass, gauge, etc. edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass, etc; The size of the rail and stile as per IS 1003 (Part-I), Kiln seasoned and chemically pressure treated complete as specified and directed.

M&L for IInd class hard wood timber framed and fixed wrought complete all as specified and directed.

S & F butt hinges 100mm size MS cold rolled medium weight complete all as specified and as directed.

S&F aluminium anodised barrel tower bolts of extruded section 200 mm long complete all as specified and as directed.

S&F aluminium sliding door bolts with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section etc length of bolt 300 mm complete all as specified and as directed.

S &F 300mm MS ordinary rat tail rod pattern spring including roller and roller plate complete all as specified and as directed.

S &F 300mm MS ordinary rat tail rod pattern spring including roller and roller plate complete in repairs (including dismentling existing door spring by means of welding) complete all as specified and as directed.

S & F in repairs 3 mm thick figured glass pin head type and glazing with oil putty not exc 0.5 Sqm in each pane complete all as specified and as directed.

S&F steel windows double shutters, one glazed and other fly proof shutter, side hung, including projecting type hinges with steel handles and steel peg stay complete with glazing bars dovetailed or welded complete including 12mm square guard bars as specified in relevent IS as specified and directed.

S&F Aluminium single leaf door on pivots alongwith hydraulic door closer (Aluminium Extruded Section), door lock, handles 5mm thick plain glass in top and 12mm thick prelaminated particle board (both side laminated) in bottom panel, fixed with rubber beading and glazing clips and using aluminum powder coated sections as given in 'JINDAL' Catalogue complete all as directed. (a) Rectangular tube - 14005 (b) Shutter vertical - 18501 (c) Shutter top rail - 19503 (d) Shutter middle rail - 20060 (e) Shutter bottom rail - 19511 (f) Glazing clips - 19352.

S&F two track sliding window with two or more shutter with 4mm thick plane glass or frosted alongwith good quality bearing, handle, lock etc using following aluminum powder coated sections as given in 'JINDAL' Catalogue. (a) Bottom frame rail - 20619 (b) Top frame & Vertical - 20681 (c) Handle (side) - 20606 (d) Shutter inter lock - 20724 (e) Shutter top & Bottom - 20844.

S&F three track sliding window with two or more shutter with 4mm thick tinted glass one shutter using stainless steel wire cloth 0.36mm nominal dia & 1.18mm width aperture for mosquito proofing with good quality bearing handle, lock, rubber beading and glazing clips etc using following aluminum powder coated sections conforming to catalogue of 'JINDAL' or of equivalent make complete all as specified and directed. (a) Bottom frame - 20620 (b) Top frame & vertical - 20621 (c) Handle (side) - 20606 (d) Shutter inter lock - 20724 (e) Shutter top & Bottom - 20844 (f) Glazing clips - 19352.

All as per item No. 131.00 above but with provision of AC opening complete all as specified and as directed.

S & F ventilators/louvers using 4mm thick x 10cm wide froasted glass strips and following aluminium powder coated sections conforming to catalogue of 'JINDAL' or of equivalent make and rubber beading etc all as directed :- (a) SP : 20048 (b) Glazing clips : 19352

Taking down existing shutters cleaning, repairing easing, making good by changing stiles lock rails top & bottom rail with cleats, rubber, beading, floor spring etc and refixing in the same position after repairing and making good distrubed area complete all as specified and directed (Note :- Replaced aluminium section will be measured seperately as supply only).

Supply only powder coated aluminium section of stiles top, bottom, locking rails for doors, windows, ventilators, partitions with one or more rebates including joining cleat for fixing etc complete all as specified and directed.

S&F in repairs Mortice lock, vertical type size 100mm of brass body, 4 lever 'Link' make complete all as specified and as directed.

S&F in repairs 5mm thick plane or frosted glass in panels of aluminium doors and partitions etc complete all as specified and as directed.

S&F in repairs 4mm thick plane or frosted glass in panels of aluminium doors, windows and partitions etc complete all as specified and as directed.

S&F in repairs MS pivots top of approved make complete all as specified and as directed.

S&F in repair hydraulic door closer aluminium body suitable for door shutter of 850 to 1000mm in width and of weight between 61 to 80 Kg of approved make of ISI marked complete all as specified and as directed.

S&F in repairs "L" clamps with necessary nut & bolts for door frame complete all as specified and directed.

S&F in repairs MS pivots bottom of approved make complete all as specified and directed.

S&F in repairs slider assembly for sliding aluminium doors with "G" section and including necessary nut and bolts fittings clamps wheel tracks etc complete all as specified and as directed.

Dismantling of single layer Mangalore pattern tiles or similar tiles in roofing etc complete all as specified and as directed.

Dismantling battens for tiles shingles etc of any size includingtiling fillets exc. 15 cm spacing etc complete all as specified and as directed.

Dismantling timber scantling 40 Sqcm and over in section in any position (unframed wok) etc complete all as specified and as directed.

Dismantling timber scantling under 40 Sqcm in section in any position( unframed wok) etc complete all as specified and as directed.

Dismantling boarding any description fixed in any position with nails etc complete all as specified and as directed.

M & L IInd class hard wood clean sawn batten at 30 cm center to center sectional area exc 5 and n.exc 15 Sqcm etc complete all as specified and as directed.

All as per item No. 149.00 above but except batten complete all as specified and as directed.

M&L roof tiles Mangalore pattern inter locking at side joints laid dry etc complete all as specified

All as per item Sl No. 151.00 above but except tiles etc complete all as specified and as directed.

M & L ridge tile or hip tiles to suit Mangalore pattern of roofing tiles bedded and jointed in CM (1:6) etc complete all as specified and as directed.

All as per Sl. item No. 153.00 above but except tiles etc complete all as specified and as directed.

S & F for 25 mm thick 2nd class H/W boarding butt joints plained both sides complete all as specified and as directed.

All as per Sl. Item No. 155.00 abvove but fixing only complete all as specified and as directed.

M&L for second class hard wood clean sawn timber fixed as in scantling complete all as specified and as directed.

M & L for IInd class hard wood plain fillets square, rectangular or triangular in section clean sawn secured with nails, sectional area exc. 13 Sqcm but n. exc 25 Sqcm etc complete all as specified and as directed.

All as per Sl. Item No. 158.00 above but except fillet complete all as specified and as directed,

Removing of old water proofing treatment including screed bed and cleaning the surface of slab with wire brushes removing dust, foreign materials including flushing at junction of wall and removing the rubbish off the premises to a distance exc 500m complete all as specified and as directed.

Removing of existing water tank of capacity 1000 or 2000 Ltr setting aside (or lowering if required) for repair, cleaning etc and reconnecting & refixing in position after carrying out necessary roof treatment including necessary fittings and GI Pipes if required complete all as specified and as directed. (NOTE : Necessary by pass arrangements for water supply is to be done by the contractor till completion of roof work.)

Removing building material exc. upto 1 km total distance including loading, unloading and stacking at the destination to a distance n.exc. 5 KM complete all as specified and directed.

M&L water proofing treatment to RCC roof slabs, walls, chajjas etc shall be carried out as specified below and as directed by Engineer-in-Charge. (a) M&L for 10mm thick plaster screed bed layer in CM 1:3 on concrete surfaces. (b) Preparing plastered surfaces of roof slab, walls, chajjas etc by brooming with broom sweeping free from dust etc and evenly applying a coat of approved bituminous priper @ 0.20 Kg/Sqm of area complete all as specified. (c) Laying APP polymer modified approved membrane non woven, polyster weighing not less than 3.5 Kg/Sqm with laps and overlaps as specified and joints sealed and applied complete by torch application method all as specified and directed by Engineer-in-Charge. Carrying out test by flooding water for 24 hrs for leakage and seepage and rectifying the same to the entire satisfaction of GE. (d) Finally applying a coat of solar reflective bituminous aluminium @ 0.15 ltr/Sqm on the top of membrane surfaces complete all as specified and as directed by Engineer-in-Charge.

M&L for Framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, frame work of water tanks and similar work conforming to Fe-290.Gde-E-165 for MS framed work as in trusses, purlins, rafters, post etc conforming to grade E-250 (Fe 410W, quality 'A') including shaped washers, including necessary cutting required length, notching, drilling, riveting and or welding or connecting with nut bolts with angle cleats, fish plate, gusset plate and also erecting in true position complete all as specified and as directed.

S&F in repairs collapsible steel gates, top hung, consisting of channel pickets, pivoted flat bars, top and bottom runnners brass handles etc as specified in SSR Part-I , erected in position and securing runners with holdfasts and brackets complete all as specified and directed.

S&F in repairs steel rolling shutters made out of 1.00mm thick laths/sheets without ball bearing as specified including top cover, anchoring rod, hasp & staples & one shop coat of primer and erected in position as indicated, manual type complete all as specified

Taking down & refixing steel rolling shutters with out ball bearing as specified including top cover anchoring rod hasp and staple and one shop coat of primer erected in position as indicated complete push pull or manual type all as specified and directed

S&F in repairs safety lever locks mild steel with 4 levers for rolling shutters all as specified and directed

S&F in repairs ball bearing for rolling shutters complete all as specified and directed

Prepration of old decorated surfaces of walls/ceiling by brooming down and scrapping whereever necessary and applying one coat of oil bound distemper complete all as specified and directed

Prepration of old decorated surfaces of walls, soffits/ facia of chajja/roof slab etc and applying one coat of cement base paint white or tinted all as specified and directed

M & L for scraping the existing plaster upto the brick work applying two coats of LP(f) & covering the entire area with polyrised poly bag with wire mesh and cover it with new plaster, followed by application of siliconate injection grout for rising dampness grouting should be identified and marked for in setting the nozzle for rising dampness. The spacing of holes will two nos hole in every one meter, using 12mm to 15mm dia drill bit, drill holes at an inclination of 45 the extent of 1/2 to 3/4 of the wall thickness and should be injected in the lowest possible point dampness and the material used in the wall and its construction, pump sufficient to create pressure of approx 3Kg/sqcm must inject chemical through pressure grouting machine. Inject the dilute liquid (1:4) by pumping till the point of return application of two coats of water based hyginic coat containing liquid is felt (min 10 lit) and allow to remain for some time before the next nozzle and observing the area for 24 hours including removing the extended/protruding nozzle and seal with the suitable compound the treated area should be washed througly followed by application of two coats of water based hygynic coat containing inentire scraped area and including removing of old material of any description, complete all as specified and directed by Engineer-in-Charge. (Note 1 :Treatment should be done by only Auth Applicator)

L.K.R.TIWARI CONSTRUCTION

SARATH ENTERPRISES

Gauri Associates