REPAIR AND POLSIHING OF CERTAIN WOODEN FURNITURE AND SOFA SETS INCLUDING TRADE PATTERN FURNITURES AT OFFRS MD ACCN UNIT LINES AND STORE YARD OF BSO (SOUTH) UNDER GE (SOUTH) BANGALORE

Amount

BED PLYWOOD TOP WITH MNF SET (Applicable to item No 01 to 05) FD-246 Removing the existing unserviceable broken wooden long rail and supply of first class hard wood (Teak wood) new long rail of size 35mmx90mmx1980 mm including 35 mm x 5mm flat iron of mild steel bent to right angles as shown on drg and as as directed.

Removing the existing unserviceable broken wooden head board including legs and supply and fix 900x400mm new head board including teak wood legs of size 60mmx60mmx400mm and all as specified and as shown on drgs.

Removing the existing unserviceable /broken foot board including legs and supply and fix 900x300mm new foot board including teak wood legs of size 60mmx60mmx30mm and all as specified/directed and as shown on drg.

Removing the existing unserviceable /broken wooden stiffeners (supporting pieces) and supply and fix first class hard wooden stiffeners of size 40cmx60cm complete all as specified/directed and as shown on drg.

Removing the existing unserviceable plywood and supply and fix 900mmx1800mm x 12mm thick plywood commercial BWR grade bearing ISI marked all as specified/directed and as shown on drg.

SIDE BOARD (Applicable to item Nos 06 to 14) FD-241 Removing the existing unserviceable top and supply and fix new top made out of 18mm thick prelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination not less than 1.5mm thick of sizes 1220mmx455mm etc complete all as specified/directed and as shown on drg.

Removing the existing unserviceable side and supply and fix new side made out of 18mm thick prelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination not less than 1.5mm thick of sizes 760mmx455mm etc complete all as specified/directed and as shown on drg. Note:-Each side shall be measured as single units.

Removing the existing unserviceable back of side board and supply and fix new back with 6mm thick plywood, grade BWR, type BB with no. of ply 5, ISI marked of sizes 1220mmx700mm all as specified/directed and as shown on drg.

Removing the existing unserviceable bottom of drawer and supply and fix new 12mm thick plywood, grade BWR, type BB with no. of ply 7 of size 380mmx450mm all as specified/directed and as shown on drg.

Removing the existing unserviceable drawer and supply and fix new drawer of size 380mmx450mmx155mm, made out of teak wood plank 12 mm thick for sides and back and 18mm thick prelaminated particle board exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination for front and 6mm thick plywood for bottom of drawer, including fittings such as knobs etc all as specified/directed and as shown on drg. Note:-Each drawer will be measured as single unit.

Removing the existing unserviceable shutter and supply and fix new shutter of size 600mmx390mm made out of 18mm thick prelaminated particle board exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, including hinges, kobs and lock all as specified/directed and as shown on drg. Note:- Each shutter will be measured as single unit.

Removing the existing unserviceable bottom of side board and supply and fix new bottom of sizes 455mmx1228mm, made out of 18mm thick plywood, grade BWR, type BB all as specified/directed and as shown on drg.

Removing the existing unserviceable leg frame and supply and fix new teak wood leg frame with legs, sizes 1140mmx 380mm, etc complete all as specified/directed and as shown on drg..

Removing the existing unserviceable broken wooden legs and supply and fix new teak wood leg, size 45mmx45mmx125mm etc complete all as specified/directed and as shown on drg. Note:- Each leg will be measured as single unit.

TABLE WRITING (Applicable to item Nos 15 to 20) FD-249,33,275 Removing the existing unserviceable broken top and supply and fix new top made out of 18mm thick prelaminated particle board exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination with 6mm thick teak wood edging, size 1145mmx600mm all as specified/directed and as shown on drg.

Removing the existing unserviceable/ damaged cupboard shutter and supply and fix new shutter made out of 18 mm thick prelaminated particle board exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, size 400mmx700mm, including piano hinges and brass lock all as specified/directed and as shown on drg.

Removing the existing unserviceable drawer and supply and fix new drawer size 300mmx600mmx75mm, made out of teak wood plank 12 mm thick for sides and back and 18mm thick prelaminated particle board exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination for front and 6mm thick plywood for bottom of drawer (Plywood, grade BWR, type BB with no. of ply 5) including fittings such as knobs etc all as specified/directed and as shown on drg. Note:- Each drawer will be measured as single unit.

Removing the existing unserviceable back and supply and fix new back size 1145mmx700mm, made out of 6mm thick Plywood grade BWR, type BB, no. of ply 5, with two coats of synthetic enamel paint over a coat of primer all as specified/directed and as shown on drg.

Removing the existing unserviceable side and supply and fix new side size 600mmx700mm, made out of prelaminated particle board, 18mm thick exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination all as specified/directed and as shown on drg. Note:- Each side will be measured as single unit.

Removing the existing unserviceable leg and supply and fix new teak wood leg size 35mmx55mmx717mm, etc complete all as specified/directed and as shown on drg.

TABLE DINING 6 PERSONS 1500mm x 900mm (Applicable to item Nos 21 to 24) FD-273,239 Removing the existing unserviceable damaged top and supply and fix with a new prelaminated particle board 18mm with 6 mm thick teak wood edging all round of size 1500mmx900mm all as specified/directed and as shown on drg.

Removing the existing unserviceable damaged front and back rails & supply and fix new teak wood front and back rails of size 25mmx100mmx1500mm all as specified/directed and as shown on drg

Removing the existing unserviceable damaged leg and supply and fix new teak wood leg of size 75mmx40mmx760mm all as specified/directed and as shown on drg .

Removing the existing unserviceable damaged side rails and supply and fix new teak wood side rails of size 25mmx100mmx900mm all as specified/directed and as shown on drg.

TABLE DINING 8 PERSONS 1800mm x 900mm (Applicable to item Nos 25 to 28) Fd-273,239 Removing the existing unserviceable damaged top and supply and fix new top with a new prelaminated particle board 18mm with 6 mm thick teak wood edging all round of size 1800mmx900mm all as specified/directed and as shown on drg..

Removing the existing unserviceable damaged front and back rails & supply and fix new teak wood front of size 15mmx100mmx1800mm and back rails all as specified/directed and as shown on drg..

Removing the existing unserviceable damaged leg and supply and fix new teak wood leg all as specified and as shown on drg of size 75mmx40mmx700mm.

Removing the existing unserviceable damaged side rails and supply and fix new teak wood side rails of size 25mmx100mmx900mm all as specified and as shown on drg .

TABLE PEG (Applicable to item Nos 29 to 32) Fd-384,25,236 Removing the existing unserviceable top and supply and fix new top of size 450x300 mm made out of 18mm thick pre-laminated particle board and 4mm thick teak wood edging round the top of table all as specified and as shown on drg.

Removing the existing unserviceable bottom rail and supply and fix new teak wood bottom rail of size 20x 40x300mm all as specified and as shown on drg.

Removing the existing unserviceable front/back rail and supply and fix new teak wood front/back rail of size 20x 40x450mm all as specified and as shown on drg.

Removing the existing unserviceable leg and supply and fix new teak wood leg of size 30x50x380 mm all as specified and as shown on drg.

TABLE CENTRE (Applicable to item Nos 33 to 36) FD-29,274,235 Removing the existing unserviceable top and supply and fix new top of size 900mm x 450mm made out of 18mm thick pre laminated particle board and provided 4mm thick teak wood beading alround of table top all as specified and as shown on drg.

Removing the existing unserviceable leg and supply and fix new teak wood leg of size 30mmx60mmx400mm all as specified and as shown on drg.

Removing the existing unserviceable long rail of size 30mmx60mmx900mm and supply and fix new teak wood long rail all as specified and as shown on drg.

All as per item Ser no 35 here-in-before but short rail of size 30mmx60mmx450mm.

TABLE 900X600 WITH DRAWER (Applicable to item Nos 50 to 53) FD-41,283,224 Removing the existing unserviceable table top and supply and fix new top of size 900mmx600mm of prelaminated particle board 18mm of size interior grade with 4mm thick teak wood edging all round all as specified and as shown on drgs.

Removing the existing unserviceable/damaged front and back rails and supply and fix new teak wood front and back rails of size 25mmx130mmx740mm all as specified and as shown on drg.

Removing the existing unserviceable damaged leg and supply and fix new teak wood leg of size 60mm to 40mm(bottom) with a height of 735mm all as specified and as shown on drg.

Removing the existing unserviceable damaged side rails and supply and fix new teak wood side rails of size 25mmx130mmx440mm all as specified and as shown on drg.

TEAPOY (Applicable to item Nos 54 to 57) FD-34,278,232,282 Removing the existing unserviceable top and supply and fix new top of size 600mmx450mm made out of 18mm thick pre-laminated particle board exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination with 4mm thick teak wood edging al-round the top of teapoy all as specified and as shown on drg.

Removing the existing unserviceable leg and supply and fix new teak wood leg of size 515mmx45mmx45mm all as specified and as shown on drg.

Removing the existing unserviceable front rail and supply and fix new teak wood front rail of size 450mmx50mmx20mm all as specified and as shown on drgs.

Removing the existing unserviceable side rail and supply and fix new teak wood side rail of size 390mmx50mmx20mm all as specified and as shown on drgs.

Book case FD-237 Preparing the wooden surfaces by scraping and filling bore holes with putty and rubbing by sand paper/abbrassive cloth throughly smooth and clean off and applying one coat of french polishing to required finish complete all as specified and as directed.

Side Board FD-241 Preparing the wooden surfaces by scraping and filling bore holes with putty and rubbing by sand paper/ abbrasive cloth throughly smooth and clean off and applying one coat of french polish to required finish complete all as specified and as directed.

Table 900x600 with Drawer FD-41,283,224 Preparing the wooden surfaces by scraping and filling bore holes with putty and rubbing by sand paper/ abbrasive cloth throughly smooth and clean off and applying one coat of french polish to required finish complete all as specified and as directed.

Table bed side FD-28,276,243 Preparing the wooden surfaces by scraping and filling bore holes with putty and rubbing by sand paper/ abbrasive cloth throughly smooth and clean off and applying one coat of french polish to required finish complete all as specified and as directed.

Table Dressing Gents FD-31,230 Preparing the wooden surfaces by scraping and filling bore holes with putty and rubbing by sand paper/ abbrasive cloth throughly smooth and clean off and applying one coat of french polish to required finish complete all as specified and as directed.

Table Dressing Ladies FD-32,251 Preparing the wooden surfaces by scraping and filling bore holes with putty and rubbing by sand paper/abbrasive cloth throughly smooth and clean off and applying one coat of french polish to required finish complete all as specified and as directed.

Bed plywood top FD-246 Preparing the wooden surfaces by scraping and filling bore holes with putty and rubbing by sand paper/ abbrasive cloth throughly smooth and clean off and applying one coat of french polish to required finish complete all as specified and as directed.

Binsoiled linen large FD-70 Preparing the wooden surfaces by scraping and filling bore holes with putty and rubbing by sand paper/ abbrasive cloth throughly smooth and clean off and applying one coat of french polish to required finish complete all as specified and as directed.

Chair dining FD-16,279 Preparing the wooden surfaces by scraping and filling bore holes with putty and rubbing by sand paper/ abbrasive cloth throughly smooth and clean off and applying one coat of french polish complete all as specified and as directed.

Chair dining Map : FD/MAPII/04 Preparing the wooden surfaces by scraping and filling bore holes with putty and rubbing by sand paper/ abbrasive cloth throughly smooth and clean off and applying one coat of french polish complete all as specified and as directed.

Chair Easy FD-17,229 Preparing the wooden surfaces by scraping and filling bore holes with putty and rubbing by sand paper/ abbrasive cloth throughly smooth and clean off and applying one coat of french polish to required finish complete all as specified and as directed.

Chair writing FD-20,280 Preparing the wooden surfaces by scraping and filling bore holes with putty and rubbing by sand paper/ abbrasive cloth throughly smooth and clean off and applying one coat of french polish to required finish complete all as specified and as directed.

Hat stand with mirror FD-233 Preparing the wooden surfaces by scraping and filling bore holes with putty and rubbing by sand paper/ abbrasive cloth throughly smooth and clean off and applying one coat of french polish to required finish complete all as specified and as directed.

Peg table FD-384,25,236 Preparing the wooden surfaces by scraping and filling bore holes with putty and rubbing by sand paper/ abbrasive cloth throughly smooth and clean off and applying one coat of french polish to required finish complete all as specified and as directed.

Sofa Set 4 Seater FD-258 Preparing the wooden surfaces by scraping and filling bore holes with putty and rubbing by sand paper/ abbrasive cloth throughly smooth and clean off and applying ono coat of french polish to required finish complete all as specified and as directed.

Sofa Set 5 Seater FD-281 Preparing the wooden surfaces by scraping and filling bore holes with putty and rubbing by sand paper/ abbrasive cloth throughly smooth and clean off and applying one coat of french polish to required finish complete all as specified and as directed.

Stool Dressing FD-27 Preparing the wooden surfaces by scraping and filling bore holes with putty and rubbing by sand paper/ abbrasive cloth throughly smooth and clean off and applying one coat of french polish to required finish complete all as specified and as directed.

Table 900x600 W/o Drawer FD-42,284 preparing the wooden surfaces by scraping and filling bore holes with putty and rubbing by sand paper/ abbrasive cloth throughly smooth and clean off and applying one coat of french polish to required finish complete all as specified and as directed.

Table Centre FD-29,274,235 Preparing the wooden surfaces by scraping and filling bore holes with putty and rubbing by sand paper/ abbrasive cloth throughly smooth and clean off and applying one coat of french polish to required finish complete all as specified and as directed.

Table dining 6 persons FD-273,239 Preparing the wooden surfaces by scraping and filling bore holes with putty and rubbing by sand paper/ abbrasive cloth throughly smooth and clean off and applying one coat of french polish to required finish complete all as specified and as directed.

Table dining 8 persons FD-273,239 Preparing the wooden surfaces by scraping and filling bore holes with putty and rubbing by sand paper/ abbrasive cloth throughly smooth and clean off and applying one coat of french polish to required finish complete all as specified and as directed.

Table office clerk wooden.FD-2201 Preparing the wooden surfaces by scraping and filling bore holes with putty and rubbing by sand paper/ abbrasive cloth throughly smooth and clean off and applying one coat of french polish complete all as specified and as directed.

Table office officer wooden DB-4199 Preparing the wooden surfaces by scraping and filling bore holes with putty and rubbing by sand paper/ abbrasive cloth throughly smooth and clean off and applying one coat of french polish complete all as specified and as directed.

Table writing FD-249,33,275 Preparing the wooden surfaces by scraping and filling bore holes with putty and rubbing by sand paper/ abbrasive cloth throughly smooth and clean off and applying one coat of french polish to required finish complete all as specified and as directed.

Teapoy FD-34,278,232,382 Preparing the wooden surfaces by scraping and filling bore holes with putty and rubbing by sand paper/ abbrasive cloth throughly smooth and clean off and applying one coat of french polish to required finish complete all as specified and as directed.

Almirah large wooden DB-4042 Preparing the wooden surfaces by scraping and filling bore holes with putty and rubbing by sand paper/abbrassive cloth throughly smooth and clean off and applying one coat of french polish of the required finishing.

Almirah med wooden DB-3959 Preparing the wooden surfaces by scraping and filling bore holes with putty and rubbing by sand paper/abbrassive cloth throughly smooth and clean off and applying one coat of french polish of the required finishing.

SOFA SETs (Applicable to item Nos 85 to 93)FD-281 Removing the existing unserviceable tapestry cloth, cushion and replacing with new tapestry cloth as per sample with foam cushion of size 560mmx530mm, 40 density, 100mm thick, including inner cloth all as shown on drgs and as directed. Note :- Each cushion for seat or back will be measured as single unit.

Removing the existing unserviceable leg from Sofa and supply and fix new teak wood leg of size 35mmx75mmx510mm all as shown on drg and as directed.

Removing the existing unserviceable arm rest from sofa and supply and fix new teak wooden arm rest all as shown on drawing and as directed .

Removing the existing unserviceable side rail from sofa and supply and fix new teak wood side rail of size 35mmx100mmx690mm all as shown on drawing and as directed .

Removing the existing unserviceable bearer from sofa long pieces and supply and fix new teak wood bearer of size 590mmx50mmx22mm all as shown on drawing and as directed .

Removing the existing unserviceable bearer from sofa short pieces and supply and fix new teak wood bearer of size 440mmx50mmx22mm all as shown on drawing and as directed .

Removing the existing unserviceable battens from sofa and supply and fix new teak wood battens of size 570mmx50mmx22mm all as shown on drawing and as directed .

Removing the existing unserviceable front rail from sofa long pieces and supply and fix new teak wood front rail all as shown on drawing and as directed .

Removing the existing unserviceable front rail from sofa short pieces and supply and fix new teak wood front rail of size 22mmx102mmx1740mm all as shown on drawing and as directed .

Chair computer/Chair revolving FD/E6/MAP/01 Removing the existing un serviceable seat (cushioned) and supply and fix the new seat of seat 510mm x 470mm x 60mm (12 mm hot pressed ply wood, upholstered with fabric and moulded polyurethane foam with PVC lipping. (Make : Godrej or equivalent)

Chair cushion with Arms/Chair visitor -TP Removing the existing un serviceable seat (cushioned) and supply and fix the new seat of seat 510mm x 470mm x 60mm (12 mm hot pressed ply wood, upholstered with fabric and moulded polyurethane foam with PVC lipping for chair cushion with arms/chair visitor all as shown on drg and as directed.

Chair revolving padded with Arm high back FD-75 Removing the existing un serviceable seat (cushioned) and supply and fix the new seat of seat 510mm x 470mm x 60mm (12 mm hot pressed ply wood, upholstered with fabric and moulded polyurethane foam with PVC lipping for chair revolving padded with arm high back all as shown on drg and as directed.

Chair computer/Chair revolving FD/E6/MAP/01 Removing the existing un serviceable back and supply and fix the new back (12 mm th hot pressed ply wood, upholstered with fabric and moulded polyurethane foam. The back form shall be designed with contour lumber support for extra comfort with PVC lipping for chair computer/chair revolving approx size of seat 510mm x 470mm x 60mm all as shown on drg and as directed. (Make : Godrej or equivalent)

Chair cushion with Arms TP Removing the existing un serviceable back and supply and fix the new back (12 mm th hot pressed ply wood, upholstered with fabric and moulded polyurethane foam. The back form shall be designed with contour lumber support for extra comfort with PVC lipping for chair cushion with arms all as shown on drg and as directed.

Chair revolving padded with Arm high back FD-75 Removing the existing un serviceable back and supply and fix the new back (12 mm th hot pressed ply wood, upholstered with fabric and moulded polyurethane foam. The back form shall be designed with contour lumber support for extra comfort with PVC lipping for chair revolving padding with arm high back all as shown on drg and as directed.

Removing the existing broken bottom gas lift (Up & Down) hydraulic with pouch (Maintenance free environmental friendly, chrome free cylinder tube shll be fixed in a MS black powder coated outer central column tube 38 mm dia and 2mm thick. It shall have 100 mm stroke length and gas pressure of 300 newton force, should under go an impact test)from revolving chairs, computer chairs supply and fix new bottom gas lift (hydraulic) with pouch of Make : Godrej or equivelent Note : Adjustable Tilting Mechanism to be designed with the following mechanism. Forward tilt, self regulating tilt tension + manual override, 4 position tilt lock. Anti-shock back mechanism to prevent back rest from hitting the user when the lock released. 360 swivel mechanism to allow fluid lateral movement)

Removing the existing broken twin caster wheel from revolving chairs ,computer chairs ,Tables TV Trolley etc ,supply and fix new fibre caster wheel Make : Godrej or equivalent

Removing the existing broken Pedestal assy (injection moulded in black 30% Glass filled nylone A 10.5 MM dia forged bright Zinc plated MS castor pin is of press fitted into each prong for holding the cators. It is 600 mm pitch-centre Dia) from revolving chairs & computer chairs ,supply and fix new Fibre Stem Base of Make : Godrej or equivalent

Removing the existing broken padded Arm rest (Black integral skin polyurethane finforced with MS insert. It shall be scratch and weather reisistant) as per sample from revolving chairs & computer chairs ,supply and fix new arm rest make : Godrej or equivalent

REENA INDUSTRIES

Global Furnisherts