SPECIAL REPAIR TO 06 QTRS OF TYPE II AND TYPE III MD ACCN IN BLDG NO P31 AND P29 AT MES COLONY UNDER GE (E) MATHURA

Amount

Taking down Chowkhats or frames with shutter without taking off shutters from the frames n exc. 1.5 sqm each complete all as specified and as directed.

Taking down Chowkhats or frames with shutter without taking off shutters from the frames area exc. 1.5 sqm but n exc 4.00 sqm each complete all as specified and as directed.

Taking down shutters of any description exceeding 1.0sqm and not exceeding 2.0sqm each complete all as specified and as directed.

M&L for Refixing door shutter in same opening of any decription exc 1 sqm but not exc 2.00 sqm each complete all as specified and directed.

S&F Pressed steel frames of size 125x60 mm made out of 1.25mm steel sheet for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., with one shop coat of red oxide primer complete as specified and as directed.

S&F Pressed steel frames of size 105x60 mm made out of 1.25mm steel sheet for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., with one shop coat of red oxide primer complete as specified and as directed.

M&L for machine factory made PCC 1:3:6 type C-0 (using 12.5 mm graded stone aggregate) as n kerb stone of size 300x3000x150mm set in cement mortar 1:4 complete all as specified and as directed.

S&F 35mm thick factory made plain framed paneled shutters, any No. of panels with panels of plywood 9mm thick or more panel construction and 12mm for single panel construction, BWR conforming to ID fixed to timber frame of 2nd class hard wood, all style & rail as per clause 8.24(a) of SSR Part-I all as specfied and directed by Engineer-in-Charge.

S&F 35 mm thick factory made glazed and skeleton shutters of 2nd class HW, open rebated and prepared to receive glass/gauze etc edges of framing plain chamfered or rounded fitted with cut or mitred beads for securing glass etc complete all as specified.

S&F stainless steel wire cloth. 0.30mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm thick single side prelam PVC sheet instead of Plain colour PVC sheet & edges will be painted to match with prelam sheet PVC sheet reinforced with M.S. square tube, supplying & fixing in opening as per specification & drawing complete all as specified.

S&F Factory made solid panel PVC molded door shutter 28-30 mm thick (style) with 2 or 6 raised panneled desighned with 2mm thick moulded prelam pvc sheet on front , 2mm plain colour PVC sheet on back face with partial core as per specification & drawing.

S&F 200mm long Aluminium anodised, barrel tower bolts of extruded section.

S&F 150 mm long aluminium handles, cast type, anodised.

S&F 100 mm long stainless steel hinges complete all as specified & directed.

S&F factory made steel window with side hung shutters including projecting type hinges with steel handle & steel peg stay complete with glazing bars, dovetailed or welded complete all as specified and as directed.

S&F factory made steel window with side hung shutters including projecting type hinges with steel handle & steel peg stay complete with out glazing bars, dovetailed or welded complete all as specified and as directed.

S&F for 4.0 mm thick sheet glass in square n exc 0.5 sqm each pane including rubber bead jointing cleat for fixing in position for aluminium window/ventilator all as specified and as directed.

S&F mid steel ventilator with top hung shutter including hinges, steel peg stay, complete incl one shop coat of zninc chromate primer.

S&F 3 mm thick figured glass pin head type and glazing with oil putty in squares n.exc 0.50 Sqm in each pane complete all as specified and as directed.

S&F mild steel framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings framework of water tanks and similar work conforming to Fe-290, Gde-E-165 complete all as specified and as directed.

S&F Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts 250 mm long of extruded sections or cast aluminium alloy and fixed complete all as specified and as directed.

S&F Aluminium floor door stopper 2 legs runner shoes at and 150mm long.

S&F in repairs brass chromium plated towel rail 'D' type 20mm dia, 600mm long between flanges fixed to wall complete all as specified.

S&F in repair curtain rod stainless steel chromium plated 20mm dia with bracket knobs including end cap complete all as specified and directed.

S&F Pre-coated coloured 200 mm long plate type, springs including roller and roller plate complete all as per specified and directed.

Dismanting floor heath and wall tiling including cement mortar bedding (but not backing) and rubbish off the premishes.

M&L Non skid coloured ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tiles exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with and incl 15 mm thick screed bed or bedding layer in CM 1:4 all as specified and directed.

M&L for Glazed ceramic coloured tiles in vertical surface of size 450x300x7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 10 mm thick rendering in cement motar 1:4 complete all as specified and as directed.

M&L Non skid coloured ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tiles exceeding 0.18 sqm but not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with and incl 15 mm thick screed bed or bedding layer in CM 1:4 all as specified and directed.

M&L Non skid coloured ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tiles exceeding 0.18 sqm but not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with and incl 10 mm thick screed bed or bedding layer in CM 1:4 all as specified and directed.

Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc laid bedded and pointed in any mortar complete all as specified and as directed.

M&L for 16-18 mm thick Green marble (of any type) work (table rubbed and polished) in shelves (veneering to wall) including 15mm thick plastre in cement mortar (1:4) and pointing in white cement (1:2 )using marble dust with admixture of pigment to match with shade of granite, complete all as specified and as directed.

M&L for Machine cut kota stone slab flooring 20-22 mm thick screed bed in cement mortar 1:3 laid and jointed with gray cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed.

M&L for Kota stone slab 18-20mm thick (one piece)in riser of steps, skirting, dado and pillar etc laid over and including 10mm thick backing coat in CM 1:4 jointed with grey cement slurry mixed with pigment to match the shade of the slab including making groove to curve skidness, rubbing and polishing complete all as specified and as directed.

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete as specified and as directed.

Demolition of brick work or stone boulder masonary built in cement mortar including all quoins arches pillars etc. but excluding ashlar facing dressed stone work and precast concrete articles complete all as specified and as directed.

Taking down cement plaster on brick or stone walls, ceiling etc including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and as directed.

M&L rendering 15mm thick on other than fair face of brick walls or concrete surface in cement mortar 1:4 mixed with liquid WPC @ 200 ml per bag of cement or as per manufactures Instructions and finishing surface even & fair complete all as specified and as directed.

M&L for rendering 10mm thick on fair faces of brick or concrete surfaces in cement mortar 1:6 and finishing the surface even & fair complete all as specified and as directed.

M&L for rendering 10 mm thick on fair faces of bricks or concrete surfaces as in ceiling surfaces in cement mortar 1:3 finished even & fair all as specified and as directed.

M&L for preparation of new surfaces of wall and applying two coats of oil bound distemper over 1 mm thick wall care putty and a coat of primer spray machine, spray hard to receive area to achieve excellent application using limited manpower including scaffolding, testles, ladders, cradles and necessary safety measures complete all as specified and as directed.

M&L for three coats of white wash on ceiling including preparation of new plaster surface complete.

M&L for preparation of new wooden surfaces of any description over 10 cm width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed.

M&L for applying two coats of synthetic enamelled paint over a coat of red oxide zinc chromate primer of any grith including preparation of new steel surfaces complete all as specified directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings n.exc 15cm thick including removal of rubbish off the premises complete all as directed.

M&L for 50 mm thick cement concrete 1:3:6 type G-1 (using 20 mm graded stone aggregate) as in plinth protection, finishing cement concrete surface even and fair without using extra cement complete all as specified and as directed.

Supply only liquid water proofing compound complete all as specified & directed

Demolition of roof treatment including PCC, Mud phuska PCC padding, plastering, APP membrane complete treatment of any thickness and in any position and removing the demolished material out of MoD land complete all as specified and directed.

M&L APP based polymeric membrane not less than 3 mm thick, weighing not less then 3 kg / Sqm, reinforeced with polyster non-woven fabric (weighing not less than 150 gm/sqm) and it shall be laid by torch application. Side overlaps shall be 75 mm and the ends shall be 100 mm and all overlaps and jointed should also be sealed by torch application. For parapets then inserted inside the parapet in a grooves.The same shall be finished by a membrane flashing over a coat of cold applied bituminous primer confiming to IS:3384. @ 0.40kg per Sqm complete all as specified and directed.

M&L for Cement concrete plain tiles 25cm x 25cm x 22mm thick, machine pressed, set, jointed and pointed in neat cement slurry in floors, and cut and polished over and including 20mm thick screed bedding layer in CM (1:4) complete with grey cement and no pigment complete all as specified and as directed.

M&L for 40 mm average thick PCC 1:2:4 type B0 (using 12.5 mm graded stone aggregate) in floors/padding finishing the surface even and fair with out using extra cement all as specified and as directed.

Taking up or down 15 mm bore of steel tubing and connections complete all as specified and directed.

Taking up or down 20 mm bore of steel tubing and connections complete all as specified and directed.

S&F 15mm bore of pipe GI medium grade steel tubes, galvanised with & including all fittings and fixed complete to walls and ceiling or laid in floors, complete all as specified and as directed.

M&L 20 MM nominal bore galvanised steel water tubing, medium grade, with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified and directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to store (measured overall as fixed along the centre line over fittings and accessories)

S&F 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed on wall complete all as specified and directed.

S&F 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints and laid in tranches or in floors all as specified and directed.

S&F 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed on wall complete all as specified and directed.

S&F 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints and laid in tranches or in floors all as specified and directed.

S&F 110mm bore PVC (SWR) bends/Tees/branch pieces any radius.

S&F 75mm bore PVC (SWR) bends/Tees/branch pieces any radius.

S&F 110mm bore PVC (SWR) vent cowl.

S&F 75mm outlet dia bore PVC (SWR) floor trap plain with grating including jointing with solvent cement.

S&F in repair bib taps cast alloy chromium plated CP fancy type, screwed for iron pipe or brass ferrule and fixed for 15 mm bore complete.

S&F in repair for stop cock angle type cast copper alloy chromium plated screwed down high pressure CP fancy type srewed both ends for iron pipe 15mm bore complete.

S&F in repair Vitreous China squatting pan, 'Orissa' pattern, size 580 X 440 mm white, with integrated foot rests including setting the trap and pan in concrete and including 10 ltr capacity PVC valveless syphonic action type low level flushing cistern and 32 mm dia PVC flush pipe complete including jointing to socket of flushing rim all as specified and as directed.

S&F in repairs Stainless steel sink with draining board made out of 1.0 mm thick sheet for kitchen incl waste pipe CI cantilever brackets and waste coupling etc complete and making good to the side of wall,connecting union to pipe, including bedding in CM to dwarf wall. Overall size 915mmx460mm bowl and size 410x330x160mm complete all as specofied.

S&F in repair for vitreous china wash hand basin,white, flat back size 580x450 mm including bracket including cutting for and pinning in ends of bracket or eracting stand and waste, PVC connection, pillar tap fixing complete all as specified.

S&F in repair brass chromium plated shower rose with 125 mm size all as specified and approved.

S&F in repair Gun metal, globe or gate valves 20 mm bore dia, with iron wheel head, screwed both ends for iron pipe and fixed all as specified.

Supply only PVC connection 15 mm size best quality with PTMT nuts 450 mm long.

Supply only pillar tap 15 mm bore cast copper alloy with fancy type, chromium plated screwed down high pressure long screwed shank and fly nuts for iron pipe all as specified and directed.

S&F in repair white colour 750 litre capacity triple layer ISI Marked rotational moulded polyethylene water storage tank (cylindrical vertical with closed top)hoisted and fixed in position including making inlet/oulet connection and fitting tank connection incl 20mm ball brass valve, tank nipple etc complete all as specified and as directed.

Supply only 32 mm waste fittings, brass, chromium plated for basins, etc. with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed.

S&F in repairs stop valves concealed type long shank & cup C, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions & fixed - bore dia of pipe 15 mm.

Supply only CP fancy type 40 mm waste fittings, brass, chromium plated for sinks,with long screwed shanks and fly nuts, flange end bedded in red lead cement and othre end fixed.

S&F 20 mm bore GI nipple for HDPE water tank.

S&F 32 mm bore Low density polyethylene pipes (LDPE) of pressure rating 6 kgf/cm2 and fittings, fixed to WHB, complete.

Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth of brick walls complete all as specified.

S&F 18 mm thick WPC board in cupboard shutter/kitchen cabinet with decorative on one side & other side balancing white necessary stainless steel drilling screws/anchoring bolt along with modular handles, design and colour as approved by GE complete all as specified and directed.

S&F 18mm WPC board in cupboard shutter/kitchen cabinet with both side balancing white fixed with necessary stainless steel drilling screws/ anchoring bolt alongwith modular handles, design and colour as approved by GE complete all as specified and directed.

S&F Continuous (piano) hinges, mild steel, bright finish or electro galvanised width of flaps (When open) in mm 40mm complete.

S&F Ball catches with 8mm dia steel ball, and brass body and striking plate including letting in and fixed for cup board/kitchen cabinet shutter complete all as specified and as directed.

S&F stainless steel kitchen plate rack overall size 750mm X 600mm X 250mm made out of 0.8mm thick stainless steel sheet etc. complete all as per specified and directed.

S&F 100 mm Hasp and staple, mild steel, wire type, stove enamelled black, including bolt to hinge plate and fixed with screws

S&F in repair plain fillets square/ rectangular in section, sectional area exc 13 Sqcm but n.exc 25 Sqcm, wrought and fixed with nails complete

S&F stainless steel handles, cast type polished bright of 100 mm size for kitchen cabinet shutters complete all as specified and as directed.

S&F Ball bearing runners 450 mm Telescopic (KTS-20) full extension load capacity 50 kg.

S&F stainless steel 304 Gde kitchen modular basket for storage of plates, cups grain basket, glass cutlery, bottles, etc as per requied size all as specified and as directed.

Demolition of cement concrete (reinforced) in roofs, floors (other than ground floors) beams, staircases, landing, chajjas and similar suspended work including removing rubbish off the premises complete all as directed.

Dismantling asbestos cement corrugated or semi corrugated sheets in roof covering incl ridge.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed.

S&F rolled mild steel joist, channel, angle or Tee section fixed independently without connecting plate etc cut to ordinary length i.e. within 20 mm of length indicated) of Fe 410 Gde E-250 quality complete all as specified and as directed.

S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet AZ-150, 0.50mm thick of any colour having tensile strength of 550 Mpa as per IS 15965: 2012 in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

S&F 40 mm bore Low density polyethylene pipes (LDPE) of pressure rating 6 kgf/cm2 and fittings, fixed to sink/WHB etc, complete.

M&L 75 mm thick cement concrete 1:4:8 type D2 (using 40 mm graded aggregate) as in sub base complete all as specified and as directed.

M&L for 80mm factory made chamfered edge precast concrete interlocking paver blocks any shape and size locally available of best quality and confirming to IS 15658-2006, M-30 Grade with grey cement and pigments with approved colour design & pattern as in footpath, parks, lawn, or light traffic ways of required strength made by table vibratory method using PU mould laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, compacted and proper embedding/ laying of inter locking paver block into the sand bedding layer through vibratory compaction by using plate vibrator folling the joints with fine sand and cutting of paver block as per required size and pattern finishing and sweeping extra sand complete grey cement and pigments complete all as specified and as directed.

M&L for P.C.C. 1:2:4 type B-1 (using 20mm graded stone aggregate) as in coping or roof kerbs on roof chamfered on edge including troating slightly complete all as specified and as directed.

Demolition and breaking up 150 mm internal dia drain pipe (salt glazed ware, AC or reinforced cement concrete) set in cement mortar including cement concrete bedding and haunching and removing the demolished material our of MoD land complete all as specified and as directed.

Construction of Soakage well of 1.80 mtr dia and 3.0 mtr deep complete all as specified and as shown in drawing No CEJZ/2004/S-35 sheet 1/1 dated 11 May 2004 (Revised 06-08-2005) which includes the following :- (i) Excavation and earth work, including R/F and removal of surplus soil. (ii) Cement concrete in foundation, brick work honey comb brick work. (iii) Reinforced cement concrete, form work, reinforcement. (iv) Precast cover slab, plastering, filling brick agreggate and all Pipes and fitting complete all as shown in drawing as specified and as directed.

Construction of septic tank for 25 users which includes, excavation in ordinary soil, PCC in foundation, brick work, RCC slab type A1 1:1½:3 reinforcement, Manhole covers, CI vent shaft and sludge chamber etc complete all as shown in drawing No CEJZ/2004/TD/S-17, Sheet No- 1/1 dated 11 May 2004 (Revised 06 Aug 2005) complete all as specified and as directed.

Excavation in trenches in any type of soil not exceeding 1.5 mtr wide and not exceeding 1.5 mtr in depth and getting out including forming botttom to required level or slope for laying pipes for foundations, shafts, wells, cesspits, manholes, pier hole etc n exc 10 sqm on plan and n. exc 1.5m in depth and getting out as in soft/loose soil complete all as specified and as directed.

Returning filing in excavation earth and ramming spreading, leveling, watering and well ramming in 25 CM layers complete all as specified and as directed.

Removing of surplus excavated earth to a distance exceeding exc 250m but n exc 500m and deposited where directed at a level no exc .5m above the starting point completed all as specified and directed.

M&L for PCC 1:4:8 type D2 (using 40mm graded stone aggregate) as in foundation and mass concrete complete all as specified and directed.

M&L for Brickwork with sub class 'B' Bricks straight or curved on plan exc 6 m mean radius built in cement mortar 1:4 complete all as specified and as directed.

M&L for rendering 15 mm thick on fair faces of brick work or concrete surface in cement mortar 1:6 finished even & smooth without using extra cement complete all as specified and as directed.

M&L salt glazed stone ware (SGSW) drain pipe 150 mm bore grade 'A' laid in trenches and jointed with cement mortar 1:1 complete all as specified and as directed.

M&L Cement concrete 1:4:8 Type D-2 (using 40 mm graded stone aggregate) as in bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for 150 mm bore pipe complete all as specified and as directed.

M&L for cement concrete 1:2:4 type B1 (using 20 mm graded stone aggregate) as in coping, benching etc complete all as directed and as specified.

M&L for extra forming fair finished drain or channels 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc. complete all as specified and as directed.

M&L for mild steel TMT bars 6 to 8mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

M&L for reinforced cement concrete type B-1 1:2:4 (using 20 mm graded stone aggregate) as in cover slab (for manholes etc) and similar articles complete all as specified and as directed. Note : Reinforcement shall be measured and paid separetly

Taking down carefully aluminum/copper point wiring (light ,fan, socket any type, power, bell etc.) complete including fixtures & fittings (such as ceiling rose, socket, Pendent, regulator, etc) and removing the material from site and making good the disturbed surfaces of walls ceiling etc complete all as specified and as directed.

M&L for Point wiring complete with 1.5 Sqmm single core PVC insulated (FRLS) cable 1100 volts grade with multi-stranded, copper conductor drawn through and including 20mm dia rigid non-metallic PVC conduit with all acessories such as internal bend end caps etc complete concealed in wall including cutting chases and making good the disturbed surface including provision of 1.5 Sqmm single core PVC insulated FRLS cable 1100 volts grade with multistrandered copper conductor cable as earth continuity conductor, fabricated steel terminal box made out of 1.60mm thick MS sheet concealed in walls for housing bottom & top cover plate and housing modular switches, sockets, regulator etc complete all as specified and as directed the followngs:-

One light/fan/exhaust fan point controlled by one way switch 5 amp complete all as specified and as directed.

One 3 pin 5 Amps socket point controlled by one way switch on same board complete all as specified and as directed.

One 3 pin 5 Amps socket point controlled by one way switch on independent board complete all as specified and as directed.

One bell point controlled by one modular push button on independent board complete all as specified and as directed.

One light point controlled by 2- way switch 5 amp complete all as specified and as directed.

All as per item No. 124.00 here-in-above but for 3pin/5pin 16Amps socket point controlled independently, with 4 Sqmm PVC insulated & unsheathed (FRLS) copper conductor cable independent Point wiring complete all as specified and as directed.

S&F ceiling rose, PVC/ polycarbonate, isolated body 65mmX50mm three terminals complete all as specified and as directed.

S&F Modular switch 6 Amps single pole one-way, 1 Module complete all as specified and as directed.

S&F Modular switch 16 Amp single pole one way,1 Module complete all as specified and as directed.

S&F Modular switch 6 Amps single pole two-way, 1 Module complete all as specified and as directed.

S&F Modular bell push 6 Amps with indicator single pole one way, 1 Module complete all as specified and as directed.

S&F Modular socket 2-in-1, 5 pins 6 Amps , combined 2 Module complete all as specified and as directed.

S&F Modular socket 2-in-1, 3 and 3&5 pins 6 /16 Amps, combined 2 Module complete all as specified and as directed.

S&F fan Regulator electronic step type 120 watt, 2 Module complete all as specified and as directed.

S&F in repairs bell, ding dong type, 230 Volts and connection complete all as specified and as directed.

S&F lamp holder, PVC / polycarbonate type with back plate suitable for batten fittings complete all as specified and as directed.

S&F surface mounted bulk head LED light fitting including 10 watt LED lamp B22 base complete with all accessories and connection complete all as specified and as directed.

S&F indoor decorative ultra slim surface/Wall mounted LED batten tube light fitting with polycarbonate channel housing & integrated electronic driver,energy efficient, 140V-270 volts,co- related colour temperature (CCT) of 6500K, >100 Lm/Watt complete with all accessories internally pre-wired with and including 1 x 20 watt LED tube and including connecting up with twin core twisted flexible copper conductor cable of suitable size complete all as specified and as directed.

S&F indoor decorative ultra slim surface/Wall mounted LED batten tube light fitting with polycarbonate channel housing & integrated electronic driver,energy efficient, 140V-270 volts,co- related colour temperature (CCT) of 6500K, >100 Lm/Watt complete with all accessories internally pre-wired with and including 1 x 10 watt LED tube and including connecting up with twin core twisted flexible copper conductor cable of suitable size complete all as specified and as directed.

S&F LED lamp, 9 watt, B-22 base complete all as specified and as directed.

Supply & fixing in repair indoor wall mounted fitting, brushed nickel finish fixture, mild steel with glass finish with opal glass diffuser, with LED retrofit bulb of capacity 09 watts complete all as specified and as directed.

S&F in repair indoor decorative ultra slim surface /Wall mounted T5 LED batten tube light fitting 9 watt with LED Tube (size within 600x25x40 mm) suitable for mirror light with polycarbonate channel housing & integrated electronic driver,energy efficient, 140V-270 volts,co- related colour temperature (CCT) of 6500K,>100Lm/Watt complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable of suitable size complete all as specified and as directed

S&F building security light bracket made out of 40mm dia medium grade GI pipe of 1.2 m length bent to required shape suitable for fixing street light fitting on Steel tubular pole including two Nos clamps made out 40mm X 6mm flat with suitable nuts and bolts including applying two coats of aluminium paint over a coating of red oxide primer complete all as specified and as directed.

Taking down old unserviceable existing MCB DB/ enclosures any size and type/ any descriptions as iron sheet scrap including MCB's/ MCCB's any type/ size and making good disturbed surface/ wall as per existing complete all as specified and directed.

S&F in replacement sheet metal enclosure MCB distribution board, SPN 12 Way, Double door, phosphatised, powder coated with 200Amp rated bus-bar, neutral link, earth bar and din rail , cable ties for cable management, 240 V complete all as specified and as directed.

S&F CRCA sheet powder coated MCB distrbution board, IP-43 IK-09 protection, double door recess mounted, triple pole and neutral 4 way with 100 Amps rated copper bus bar, 415 volt complete all as specified and as directed. Make : Havells/L&T/Simens/Schenieder

S&F in repair MCB TPN 63 Amps, 'C' series, breacking capacity 10KA, 415V complete all as specified and as directed.

S&F in repair MCB SP 32 Amps, 'C' series, breacking capacity 10KA, 240V complete all as specified and as directed.

S&F in repair MCB SPN 32 Amps, 'C' series, breacking capacity 10KA, 240V complete all as specified and as directed.

S&F MCB SP 5-32 Amps, 'C' series, breacking capacity 10KA, 240V complete all as specified and as directed.

Taking down electric meter from location and refixing the same on LT panel/ walls as per existing location with nut, bolt and all electrical connection from the DBs with suitable thimbles including making connection complete all as specified and as directed. Note : connection cable 10Sqmm multistranded copper conductor with flexible pipe main DB to meter deemed to included in quoted rate nothing paid extra.

Taking down the ceiling fan of 1200/140mm sweep carefully from its installed position, dismantling complete, cleaning all dust, applying grease for bearings, reassembling the fan and blades, painting of fans with white synthetic enamel paint by spraying with spray gun as directed and hanging/fixing the fan in its original position and replacement of down rod, rubber real, connector nut bolt complete and pvc sheathed and insulated 1.5 sqmm copper wire from fan terminal to ceiling rose and testing on completion complete all as specified and as directed.

S&F only capacitor 2.5 to 3.5 MFD suitable for ceiling fan/ exhaust fan complete all as specified and as directed.

Dismantling of worn out/burnt out windings of ceiling fan sweep size 1200/1400 and re-winding the motor of ceiling fan with super enamelled copper wire of existing gauge, varnishing with approved quality insulating varnish complete including replacement of split/safety pins, locking nut, check nut and testing for original and consumption complete all as specified and as directed.

S&F Ball bearing suitable for ceiling fan/exhaust fan/fresh air fan of any type as per existing required including proper alignment of shaft and testing complete all as specified and as directed.

S&F Bush made out of Gun metal suitable for ceiling fan/exhaust fan/fresh air fan as required at site complete all as specified and as directed.

S&F Canopy (set of two) suitable for ceiling fans of any make, type and size complete all as directed.

S&F Down rod MS grade 15 mm bore of length upto 180 cm suitable for ceiling fans of any type and size including cutting, drilling holes, making thread and painting complete all as directed.complete all as specified and as directed.

S&F hanging only ceiling fan and replacement of suitable length down rod complete all as directed.

S&F exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, copper winding of sweep 250 mm complete all as specified and as directed.

S&F exhaust fan steel body AC single phase, 50Hz, 230V, 300 mm sweep with blades, and frame and louvers complete all as specified and as directed.

Cutting holes for air ducting of exhaust fan in circule/square shape or as per site requirement into or through existing wall or PCC Block masonry built in cement mortar or cement lime mortar and stone walls built in lime mortar of superficial area exc 400 sqcm but n.exc 0.10sqm to a depth of 30cm including making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 complete all as specified and as directed.

M&L for Sub Main Wiring with two runs single core 10 Sqmm PVC insulated unsheathed (FRLS) cable with multistranded, 1100 volts grade copper conductor drawn in suitable size of rigid non-metallic PVC conduit (not less then 25mm dia med gd) and its all accessories complete concealed in wall/roof incl cutting & chases( making good all to the disturbed surfaces as per existing) with and including 10 sqmm copper green colour earth incl taking down old U/S wiring complete all as specified and as directed. Note: Two runs 10 sqmm, one run of 10 sqmm earth wire & One run of PVC conduit shall be measured as one unit length.

Supply, laying, jointing and testing of XLPE insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor of size 25 Sq mm 4 core, laid in trenches/ duct/ fixing on walls/ poles or passing through HDPE double wall corrugated pipe (outer dia should not be less than 40mm) including connecting with suitable lugs, glands, nuts and bolts in existing panel from pole/ main panel box and testing complete all as specified and directed. Note :- HDPE pipe rate shall be deemed in quoted rate above.

Excavation in trenches not exceeding 1.5 mtr wide and not exceeding 1.5 meter in depth for laying of cable and getting out in soft/ loose soil complete all as specified and directed by Engr-in-charge.

Returning, filing in including spreading, levelling, watering and well ramming excavation soil in layers not exceeding 25 cm thick each, back in trenches after cables have been laid and tested, poles, stays, struts have been erected and tested, complete all as specified and as directed.

Removing excavated surplus (soil) obtained from excavation to a distance not exceeding 50 metre and depositing where directed at a level not exceeding 1.5 metre above the starting point complete all as specified and as directed.

Material and labour for Earthing complete with GI earth plate 600mm x 600mm x 6 mm thick electrode buried directly in ground (earth pit not less then 2.25 metres deep below ground level ) with top edge of the plate not less then 1.5 metres below normal ground level connected to GI wire 4.0 mm as earth lead by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 of MES schedule Part-I and incl 15 mm bore light grade GI protection pipe (upto 7.5 metres beyond outer edge of earth pit) PCC M-10 grade (Nominal Mix) using 40mm graded stone aggregate in pit with 40mm thick RCC cover in reinforced cement concrete M-15 grade (Nominal Mix) using 20mm graded stone aggregate, reinforced with 8mm dia bar both way @ 150mm c/c, watering arrangement with funnel and wire mesh and 20 mm bore light grade GI watering pipe, common salt and chaarcoal filling, necessary excavation and earth work complete.

Taking out the electric geyser of capacity 25 ltr carefully from its installed position by disconnecting inlet and outlet water pipes, dismantling the unit and replacing the defective parts and painting with one coat of synthetic enamel paint and writing MES No and safely keeping aside & refixing in its original position after completion of civil work and reconnecting the inlet/outlet water pipes and testing on completion complete all as specified and as directed. Note : The spare parts required shall be measured and paid separately under relevant items.

Supply only the following items suitable for electric geyser of capacity 25 ltrs :-

Heating element 1.5/2 KW ISI marked including rubber Gasket as per existing type

Thermostat suitable for 25 Ltr Geyser (as per the existing type)

Hot water / cold water pipe 600 mm long as per existing type.

S&F AC Box with 20A SP MCB, Metal enclosure complete all as specified and as directed.

M&L for Sub Main wiring for DB to DB with two runs single core 10 Sqmm PVC insulated unsheathed (FRLSH) cable with stranded copper conductor drawn in suitable size of rigid non-metallic PVC conduit and its all accessories complete concealed in wall/roof with and including 10 Sqmm copper green color earth wire all as specified and directed by Engineer-in-charge. (02 run 10 Sqmm single core cable, one run of 10 Sqmm earth wire & one run of PVC conduit will meaured as one RM)

M/s RCC (BID ID -3396906)

shyam construction (BID ID -3397703)

BHARDWAJ CONSTRUCTIONS (BID ID -3396593)

mh enterprises (BID ID -3398068)

M/s Orient Traders (BID ID -3397386)

Ms Kamal Kant Agarwal (BID ID -3397995)

M/s Aditya Enterprises (BID ID -3395581)

ISHWAR ENTERPRISES (BID ID -3397455)

Deepak Saxena (BID ID -3396664)