Providing RCC foundation, soling, PCC Masonary, Plastering etc. for fixing new filament winding machine laboratory in Textile department

Excavation for foundation in earth, soil of all types, sand, gravel and soft murum, including removing the excavated material up to a distance of 50 m. beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift upto 0.00 to 1.50 m.) By Manual Means

Providing dry/ trap/ granite/ quartzite/ gneiss rubble stone soling 15 cm to 20 cm thick including hand packing and compacting etc. complete.

Providing and laying Cast in situ/Ready Mix cement concrete in M15 of trap/ granite/quartzite/gneiss metal for foundation and bedding / steps including steel centering, formwork, laying/pumping, compacting, roughening them if special finish is to be provided, finishing uneven and honeycombed surface and curing etc. complete. The Cement Mortar 1:3 plaster is considered for rendering uneven and honeycombed surface, only. Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc. (Wooden centering will not be allowed.),with fully automatic micro processor based PLC with SCADA etc complete.

Dismantling brick masonry in lime or cement mortar and stacking the materils as directed with all leads, lifts etc.complete.

Removing doors and windows with frames and stacking the materials as directed with all leads, lifts etc. complete.

Removing ventilators and small windows with frame and stacking the materials with all leads, lifts etc. complete.

Removing the existing cement plaster of any thickness without causing dust nuisance and stacking the material at place as directed by engineer in Charge.

Removing cement tiles, or marble or polished shahabad floor or dado without bed concrete including stacking the materials as directed with all leads, lifts etc. complete

Removing rich mix cement concrete including stacking the spoils as directed with all leads, lifts etc, complete.

Removing G.I. or A.C. sheet roofing including purlins, principal rafters etc. including sorting serviceable and unserviceable materials, stacking the same as and where directed in the compound including scaffolding etc. complete.

Dismantling and disposal of existing any kind ceiling, including removing steel truss ,supporing structures, partition and other unwanted material ans stacking the same as directed by Engineer In charge.etc complete.

Treating rising Dampness (Capilari action) in masonry wall using low pressure pump and injecting an alkali ,silicon,silicone or stearate fluid into holes of 16 mm dia with 200 mm length drilled into walls at spacing of every 9 inches .Fill the holes with polymer modified mortar .Finish the mortar joints between the bricks masonry etc complete.

Providing internal / external 20 mm thick Ready Mix plaster confirming to IS:4031(Part?4) 1988 and IS 383-1970 in a single coat using Cement mortar of proportion 1:4 containing special type of polymer additives about 0.4%, to all type of surfaces in all positions including scaffolding and curing etc.complete.

Providing and applying Two coats of wall care Putty on plastered surface and Ceiling and Walls to prepare surface even and smooth of approved make, etc complete.

Providing and applying water proofing treatment using acrylic polymer modified cement based water proofing coating with fibre glass mesh mixing at the rate of powder to liquid (2:1) by weight covering 9 to 10 Square Metre /Kilogram with two coat using approved chemicals for masonry and concrete surface by brush covering 7 years guarantee on Stamp Papers etc. complete.

Providing & applying anti corrosive treatment to exposed reinforcement portion of beam/ column with one coat of alkaline Rust converter feovert/ rusticide or equivalent on exposed reinforcement after celaning the surface with wire brush, followed by two coats of anticorrossive epoxy based two component zinc rich primer MasterEmaco P 130 of BASF phenolic IPNET RB/ Polyalk flxoprime or equivalent rebar protection coating on exposed reinforcement and concrete penetrating corrossion inhibitor EPCO KP-100/ POLALK EP 113/ Masterseal 1414 of BASF/ FOSROC or equivalent over adjoining concrete surface etc complete.

Providing & applying of bond coat approved epoxy resin master brace 1414 of BASF/ EPI bond of krishna conchem/ or equivalent before polymer plaster/ concrete to have the perfact bond between old concrete and new concrete/ polymer plaster surface within half and hour of after application of bond coat conforming to ASTM C 881 Type 2, using nylon brushes scaffolding labour etc. complete

Providing & applying Ready mix polymer modified cement mortar of average thickness 15mm using polymer in one or more layers in proportion 1:5:15 of polymer cement quartz sand as manufacturers specifications in specific layers, curing the surface after 72 hours of application with wet gunny bags etc complete

Providing & filling of micro concrete & 10mm aggrigate (1:1) including sacrificial leakproof MS shuttering includes cost of higher charges of on machineries, barch, cost of all tools & all labor charges complete. Note: Voloume of micro concrete will be counted by actual bags received.

Shifting of existing inside laboratories furniture, cupboards, other equipment’s, machines carefully and conveying and stacking the same outside the laboratory as directed by Engineer In charge /HOD textile etc complete.(Lumpsum basis work)

Providing fly ash brick masonry with conventional / I.S. type fly ash bricks in C.M. 1:6 in foundation and plinth including bailing out water manually striking joints, racking out joints watering and scaffolding etc. complete.

Providing and laying vitrified mirror / glossy finish tiles decorative type having size 590 mm to 605 mm x 590 mm to 605 mm of 8 to 10 mm thickness and confirming to IS 15622-2006 ( group Bla) of approved make, shade and pattern for flooring in required position laid on a bed of 1:4 cement mortar including neat cement float, filling joints, curing and clearing etc. complete. Minimum Thickness of vitrified tiles 8 mm and base price Rs.608/- per sq.m

Providing and laying in situ /Ready Mix cement concrete M-20 of trap / granite /quartzite/ gneiss metal for R.C.C. work in foundations like raft, strip foundations, grillage and footings of R.C.C. columns and steel stanchions etc. including bailing out water, Steel centering formwork, laying/pumping cover blocks, compaction and curing roughening the surface if special finish is to be provided (Excluding reinforcement and structural steel) etc. complete, with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

Providing and fixing in position TMT - FE - 500 bar reinforcement of various diameters for R.C.C. pile caps, footings, foundations, slabs, beams columns, canopies, staircase, newels, chajjas, lintels pardis, copings, fins, arches etc. as per detailed designs, drawings and schedules. including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required complete.

Providing and fabricating structural steel work in rolled sections like joists, channels, angles, tees etc. as per detailed design and drawings or as directed including cutting, fabricating, hoisting, erecting, fixing in position making riveted / bolted /welded connections without connecting plates, braces etc. and including one coat of anticorrosive paint and over it two coats of oil painting of approved quality and shade etc. complete.

Providing and fixing Modular false ceiling of 600 x 600 mm center to center and 13 mm thick square mineral fiber board to be fixed on frame work of alluminium sections for suspended false ceiling consisting of alluminium T 2”x1 ½” (50 mm x 40 mm) weighing 0.39 Kilogram/m at 60 cms center center and fixed with ½” x ½” (15 x 15 mm) flanges weighing 0.19 Kilogram/m suspended on 6 mm dia mild steel rod weighing 0.22 Kilogram/m, fixed on wall and beams including rounding of the edges with alluinium T of 2” x 1 ½” (50 mm x 40 mm) weighing 0.39 Kilogram/m etc. (all alluminium sections shall be anodized) including all labour, material, lifts etc. complete.

Providing and applying interior wall finish luster of approved make on internal wall surface and ceiling as detailed below Scrapping the surface with emery paper and wipe clean wall primer with brush with mineral turpentine with brush 8 to 10% and oil 15 to 20% with roller and allowing to dry for a period 6 to 8 hours. wall putty with appropriate proportion of water allowing to dry for period 4 to 6 hours. Scrapping with Emery paper 180 and wipe clean. Applyingwall primer with brush with mineral turpentine 8 to 10% and oil 15 to 20% with roller Scrapping Emery paper 320 and wipe clean, interior wall finish luster 1st coat with brush/rubber/spray with mineral turpentine 7 to 9% and Oil with roller 19 to 21% After 8 hours of activity Applying 2nd coat or wall finish Lustre with mineral turpentine 7 to 9 % with brush and Oil with roller 19 to 21% after allowing dry for the period of 6 to 8 hours activity. (with Texture finish on one wall of classroom as per design given by engineer incharge)

Providing and fixing fully glazed double leaf window shutter with openable fanlight including Country cut teak wood 25 mm thick style and rails with plain / obscured glass panels 5 mm thick as per drawing or as directed by the Engineer in charge with stainless steel fixtures and fastening and finishing the wood work with oil painting three coats etc. complete.

Removing the existing oil paint from doors and window surfaces upto the original wood surface by using flame and grinder etc complete. The surfaces should got approved from Engineer in charge before applying malimine polish.

Providing and applying melamine polish of required finish to the wood work by spray machine including knotting and preparing the even surface by scraping, applying French polish , scaffolding if required etc. complete.

Providing and fixing solid core flush door shutter in single leaf 32 mm thick decorative type of exterior grade as per detailed drawings approved face veneers 3 mm thick on both faces or as directed, all necessary beads, mouldings and lipping, wrought iron hold fasts,chromium plated fixtures and fastenings, with brass mortise lock, chromium plated 0handles on both sides, and finishing with French Polish etc. complete.Base price of of solid core flush doors Rs.1050/- per sq.m

Removal of debris including loading and unloading on approved dumping ground by truck for the lead of 50 kilometers.etc complete.

Point wiring for light/bell/exhaust fan in 20 mm FRLS grade HMS PVC conduit with 1.5 sq.mm (2+1E) FRLSH grade copper wire, modular type switch, earthing and required accessories as per specification No: WGPW/SW.

Secondary point wiring for additional light/ bell point in min 20 mm metal conduit with 1.5 sq.mm (2+1E) FRLSH grade copper wire with required accessories as per specification No: WG-PW/SW

Point wiring for ceiling fan in 20 mm FRLS grade HMS PVC conduit with 1.5 sq.mm (2+1E) FRLSH grade copper wire, modular type switch, earthing and required accessories as per specification No: WG PW/SW

Point wiring for independent plug in 20 mm FRLS grade HMS PVC conduit with 1.5 sq.mm (2+1E ) FRLSH grade copper wire, modular type switch, earthing and required accessories as per specification No: WG-PW/SW

Wiring for plug on board with Switch socket surface/concealed type, copper wiring and earthing and with modular accessories as per specification No: WGPW/ CW

Supplying and erecting LED Panel Light(600mm X 600mm) Max. 30 W having CRCA powder coated housing, polystyrene diffuser having system lumens output of Min. 3600 Lumens, min. efficacy of 120 lumen/W, CRI>80, CCT upto 6500K, Beam Angle of 120 deg., max. ripple of 5%, THD<10%, p.f. >0.95, operating range of 120-270V, surge protection of 2.5 kV, Life class of 50,000 Hrs. at L70B50 including driver, having mounting arrangement with board for surface type or spring loaded mounting clips complete with 3 years warranty.

Supplying and erecting energy saving ceiling fan 230 V A.C. 50 cycles 1200 mm complete erected in position as per specification no. FG-FN/CF

Supplying and erecting mains with 3x2.5 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places as per specification No: WG-MA/BW

Supplying and erecting mains with 3x4 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places as per specification No: WG-MA/BW

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 16 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU

Supplying and laying HMS PVC conduit FRLS grade 25 mm dia with necessary accessories in RCC work/false ceiling/false flooring as per specificationNo. WG-MA/CC.

Supplying and erecting modular type 3 pin 6A multi socket with safety shutter, duly erected on provided plate and box with wiring connections complete.

Supplying and erecting modular type 3 pin 6 / 16A multi socket with safety shutter, duly erected on provided plate and box with wiring connections complete.

Supplying and erecting modular type switch 6A / 10A duly erected on provided plate and box with wiring connections complete.

Supplying and erecting modular type (two module) electronic step regulator for fan, duly erected on provided plate and box with wiring connections complete.

Supplying and erecting modular type blanking plate one module, duly erected on provided plate & box.

Supplying and erecting PVC Surface modular switch box with double mounting plate for 3 module duly erected.

Supplying and erecting PVC Surface modular switch box with double mounting plate for 4 module duly erected.

Supplying and erecting PVC Surface modular switch box with double mounting plate for 6 module duly erected.

Supplying and erecting PVC Surface modular switch box with double mounting & front plate for 8 module complete duly connected.

Supplying and erecting PVC Surface modular switch box with double mounting plate for 12 module duly erected.

Supplying and erecting PVC Surface modular switch box with double mounting plate for 16 / 18 module duly erected.

Supplying & erecting triple pole and neutral distribution board (TPNDB), SPMCB of 4 ways/phase (12 poles), with door, 1.2mm thickness,surface/flush mounted, IP 43 protection on iron/GI frame (horizontal busbar type) as per specification no. SW-SWR/MCBDB

Providing & erecting 3 Pole MCCB, 415 V, 100A, rated short-circuit breaking capacity 25 kA (Ics=100% of Icu), adjustable thermal (overload) setting and fixed magnetic setting with provided leads, provision for installation of shunt/UV/trip alarm contact. MCCB with phase barriers on both sides, insulation withstand capacity 800V, no line-load bias in provided enclosure/panel as per specification no. SW-SWR/MCCB

Supplying, erecting & marking SPMCB 6A to 32A, B-series with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB

Supplying, erecting & marking TPMCB 40A to 63A, with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB

Removing/ Dismentalling all existing Light Fixtures/ Fans/ Switchboards/ Distribution boards with electrical wiring & other accessories etc complete.

Supply & Installation of cables to extend existing cables and terminate with cable lugs & glands, etc. complete.(Cable Sizes: 1 to 3 core, 2.5 Sqmm to 25 Sqmm cables)