GE(S)/M-70/2019-20

Amount

Taking down chowkats or frames with shutters (without taking off shutters from the frames) not exceeding 1.5 sqm each and removing from site. Note - Quoted rate shall be deemed to be include for cutting holes/demolition of PCC blocks etc for taking down chowkats and making good the damaged surfaces in CM 1:3 all as directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) exceeding 1.5 sqm but not exceeding 4 sqm each and removing from site. Note - Quoted rate shall be deemed to be include for cutting holes/demolition of PCC blocks etc for taking down chowkats and making good the damaged surfaces in CM 1:3 all as directed.

S&F rolled mild steel of grade Fe-290 (Grade E-165) in framed work as in doors or gates of angle or other section with gusset plates, rails braces, etc. complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete.

S&F rolled mild steel of grade Fe-290 (Grade E-165) in rolled section as in frames for doors/windows, framing for cladding, glazing and the like fixed with angle cleats and connecting plates, etc.

S&F 35 mm thick factory made second class hard wood glazed and skeleton shutters (three panels), open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc. sizes of members of shutters as specified in SSR Part-I, Section 8, clause 8.24(a), supplied and fitted to chowkats.

S&F 35 mm thick factory made, second class hard wood, plain framed, panelled shutter (three panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS: 1003 (Part I), kiln seasoned and chemically pressure treated.

S&F pressed steel frames of size 125 x 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified.

S&F pressed steel frames of size 105 x 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified.

M&L for PCC 1:3:6 type C-0 using 12.5 mm graded stone aggregate in cills, steps, bands, copings, bed plates, blocks for inserting hold fasts, filling back of chowkats etc. and the like including weathering, slightly rounded or chamfered angles and throating as directed.

S&F 250 mm long aluminium alloy, anodized, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy.

S&F 200 mm long aluminium, anodized, barrel tower bolts of extruded section and fixed.

S&F 125 mm long aluminium handles, cast type, anodised.

S&F 300 mm, mild steel, ordinary rat tail rod pattern springs including roller and roller plate complete.

S&F butt hinges, medium weight, cold rolled, mild steel of size 100 mm.

S&F 50 mm dia, polished, hard wood knobs fixed with screws.

S&F galvanised mild steel wire cloth, 0.56 nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanised wire staples

S&F box type steel windows comprised of tubular frame and shutters made out of 1.25 mm thick M S sheet tube factory made with double side shutters wire gauged shutter & glass glazed shutter (wire cloth and glass panes only shall be measured and paid seperately) with side hung shutters with steel handle and steel peg stay dovetailed or welded incl 2 Nos tower bolts 100 mm long for each leaf and 10 mm square bar grills at spacing as shown on drg welded to FI frame work, including other fittings, hinges, handles, tarred hold fasts, PCC blocks etc all as shown on drg No CEPZ/TD-354/09 sheet 1/3 to 3/3 complete all as specified and directed.

S&F sheet glass 3 mm thick, ordinary quality and glazing with oil putty or wooden beads supplied with shutters in square n. exc. 0.5 sqm in each pane.

S&F sheet glass 3 mm thick, ordinary quality and glazing with oil putty or wooden beads supplied with shutters in square n. exc. 0.5 sqm in each pane including hacking out old broken glass.

M&L for preparation of new or previously untreated steel surfaces of any description, over 10 cm in width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer.

M&L for preparation of old painted steel surfaces of any description, over 10 cm in width or girth, not otherwise described and applying one coat of synthetic enamel paint.

M&L for preparation of new or previously untreated wooden surfaces of any description, over 10 cm in width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of pink primer.

Taking down cement plaster, any description on brick, concrete or stone walls or ceiling including racking out joints, hacking for key, scrubbing down with water etc and removal of rubbish off all as specified and directed.

M&L for rendering 10 mm thick in CM 1:6 on brick work or concrete surfaces finished even and smooth without using extra cement.

M&L for 5 mm thick rendering in CM 1:3 over concrete surfaces in ceiling (facia/ceiling/edging of chajjas and roof projection) , finished even and smooth without using extra cement, complete all as specified.

M&L for rendering 5 mm thick in CM 1:4 mixed with liquid water proofing compound @ 0.200 litre per bag of 50 kg of cement, over and including 10 mm thick rendering in CM 1:6 on brick work or concrete surfaces. Note:- Liquid water proofing compound shall be measured and paid for separately as “Supply only”

M&L for rendering 10 mm thick in CM 1:3 on concrete surfaces in ceiling (facia/ceiling/edging of chajjas and roof projection) including finishing even and smooth without using extra cement.

M&L for preparation of new plastered or unplastered surfaces of walls and applying two coats of distemper oil emulsion, white or tinted, over and including a coat of 2 mm thick wall care putty all as directed.

M&L for complete removal of existing treatment from walls and applying two coats of distemper oil emulsion, white or tinted, over and including a coat of 2 mm thick wall care putty all as directed.

M&L for preparation of new plastered or unplastered surfaces of walls and applying two coats of cement base paint, white or tinted, over and including a coat of alkali-resistant priming paint all as directed.

M&L for preparation of old decorated plastered or unplastered surfaces of walls by brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil & greasy spots including cornices etc and applying one coat of cement base paint, white or tinted, all as specified and as directed by Engineer-in-Charge.

M&L for preparation of newly plastered or unplastered surfaces of ceilings and applying three coats of white wash.

M&L for preparation of old decorated plastered or unplastered surfaces of walls by brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil & greasy spots including cornices etc and applying two coats of white wash all as specified and as directed by Engineer-in-Charge.

M&L for preparation of newly plastered or unplastered surfaces of ceilings and applying three coats of white wash.

M&L for preparation of old decorated plastered or unplastered surfaces of ceiling by brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil & greasy spots including cornices etc and applying one coat of white wash all as specified and as directed by Engineer-in-Charge.

M&L for non skid ceramic tiles, coloured, 7 to 8 mm thick in floors etc. (square/rectangular) area of each tile exc. 0.11 sqm but n. exc. 0.18 sqm, set & jointed in neat cement slurry & pointed in white or coloured cement to match over and including 15 mm thick screed bed in CM 1:6.

M&L for 25 mm thick PCC 1:2:4 type B-0 using 12.5 mm graded stone aggregate in sub floors.

M&L for 18 to 20 mm thick black marble work of Bhaislana zebra (table rubbed and polished) in cooking platform, pillars, window-cills, jambs, steps and like in CM 1:4 over and including 15 mm thick screed in CM 1:6 including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade complete all as specified and directed.

Demolition of stone slabs and tiles of any description or thickness in floors and aprons etc. laid, bedded and pointed in any mortar and removing from site all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings n. exc. 15 cm thickness (below or above ground level) and removing from site all as specified and directed.

M&L for 75 mm thick PCC 1:3:6 type C1 using 20 mm graded stone aggregate in plinth protection. Concrete shall be laid in alternate bays n.exc 3 m in length finished fair and even including provision of joints of 6 mm wide and 10 mm deep along the wall and bays filled with bitumen mastic (1:3).

Dismantling water tanks of any description, exc. 250 & n. exc. 500 litres capacity and removing from site.

Dismantling water tanks of any description, exc. 500 & n. exc. 1000 litres capacity and removing from site.

S&F 500 litres capacity rotational moulded polyethylene water storage tanks triple layer (cylindrical vertical with closed top), hoisted and fixed in position all as specified in SSR Part-I, connecting up pipes including 20 mm bore ball valve high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball screwed for iron pipe and fixed. (Minimum weight 210 gms.)

S&F 1000 litres capacity rotational moulded polyethylene water storage tanks triple layer (cylindrical vertical with closed top), hoisted and fixed in position all as specified in SSR Part-I, connecting up pipes including 20 mm bore ball valve high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball screwed for iron pipe and fixed. (Minimum weight 210 gms.)

S&F in repairs 25 mm dia gun metal, globe or gate valve, with iron wheel head, screwed both ends for iron pipe.

S&F in repairs 20 mm dia gun metal, globe or gate valve, with iron wheel head, screwed both ends for iron pipe.

Taking up or down steel tubing 15 mm bore and connections including cleaning for refixing or removing from site.

Taking up or down steel tubing 20 mm bore and connections including cleaning for refixing or removing from site.

Refixing old steel tubing, 15 mm bore, and connections in new or old position (Walls, ceiling, floors, etc.) NOTE :- Steel tubes obtained from item No. 51.00 above shall be used under this item.

Refixing old steel tubing, 20 mm bore, and connections in new or old position (Walls, ceiling, floors, etc.) NOTE :- Steel tubes obtained from item No. 52.00 above shall be used under this item.

Supply and laying 15 mm bore tubes, galvanized steel, medium grade, with all fittings and fixed complete to walls and ceilings or laid in floors all as specified and directed.

Supply and laying 20 mm bore tubes, galvanized steel, medium grade, with all fittings and fixed complete to walls and ceilings or laid in floors all as specified and directed.

S&F in repairs 15 mm bore bib taps, cast copper alloy, fancy type, chromium plated, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule.

S&F in repairs vitreous china wash basin, white, flat back, size 550x400mm including brackets, cutting for and pinning in ends of brackets or erecting stand, brass chromium plated perforated waste coupling/fittings 32 mm dia with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed and PVC waste pipe of 32 mm bore and of suitable length, complete all as specified.

S&F in repairs 15 mm bore pillar taps, cast copper alloy with capstan heads, chromium plated, fancy type, screwed down high pressure with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly nuts, screwed for iron pipe and fixed.

S&F in repairs soap dish, stainless steel, approximate size 160x 160x90mm complete all as specified and directed.

S&F in repairs brass chromium plated tubular towel rail, 20 mm dia, D type, 60 cm long between flanges.

S&F in repairs, 15 mm bore stop valve, fancy type, chromium plated with long shank and cup (concealed type), screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipe or for unions.

S&F in repairs 15 mm bore stop valve/angle valve, cast copper alloy, fancy type, chromium plated, screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipe or for unions.

S&F in repair PVC connection 15 mm size with PTMT nuts of length 600 mm.

S&F in repair cast iron floor trap, 75 mm dia of outlet, with grating including jointing to waste pipe fixed in cement concrete type B1 (1:2:4).

Taking down eaves gutters and rain water pipes (any size or pattern) including all fittings, heads, shoes, bends, swan necks, etc, including cleaning or refixing or removal from site all as specified and directed. (measured overall as fixed along the centre line over fittings and accessories)

S&F 110 mm bore UPVC (SWR) pipes type ‘A’, single socketed, in any length, with rubber ring joints fixed to walls.

S&F 110 mm bore UPVC (SWR) bend, with oval access door, suitable for type ‘A’ pipes, any radius comple.

S&F sink made of stainless steel 1.00 mm thick kitchen or laboratory with plugs, washers and wastes, including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm, bowl size 410mm x 330mm x 160mm and PVC waste pipe of 32mm bore and of suitable length, complete all as specified.

Supply and fixing factory made 18mm(+ 0.7mm) thick PVC sheet one side prelam sheet for cupboard shutter of density 600kg/Cbm bent 90° and finish at all edges at level for making edges at level for making edge lipping/bending or 0.5mm thick PVC sheet lipping at 4 edges using bonding tape etc. Complete as per direction of Engineer-in-Charge, Manufacture specification.

S&F continuous (piano) hinges, mild steel, bright finish or electro galvanized width of flaps (when open) 30 mm.

S&F "Rajshri /Accucel/Plasopan " brand factory made PVC door/Cupboard frame (prelam) - of size 115mm x 50mm with a wall thickness of 5mm, made by joining 3 Nos heat bent 'C' channel of 5mm PVC sheet density 600kg/Cbm manufactured by ISO 9001-2008 certified company of size 35mm x 35mm x 35mm and 50mm x 45mm x 50mm & 35mm x 35mm x 35mm using solvent cement. The two side 'C' channel shall be reinforced with 19mm x 19mm M.S. square tube of 19 gauge. All three 'C' channel shall be fixed to flat base of 5mm PVC sheet with solvent cement. The door frame shall be mitre cut to two corners and jointed by inserting 4 Nos. 150 mm long brackets of 15mm x 15mm M.S. square tube inside the 19mm x 19mm square tube. The door frame shall be fixed to the wall using 65/100mm long MS screws through the frame by using PVC fasterner. A minimum of 4 Nos of screw to be provided for each vertical member and minimum 2 Nos for horizontal member etc. complete as per direction of Engineer-in-Charge, manufacturer's specification & drawing.

S&F hasp and staple of size 100 mm, safety type, aluminium anodised with mild steel hinge pin including bolt to hinge plate and fixed with screws.

S&F hasp and staple of size 75 mm, safety type, aluminium anodised with mild steel hinge pin including bolt to hinge plate and fixed with screws.

M&L for cutting holes into or through brick walls built in cement mortar and making good in cement mortar 1:3 or cement concrete 1:2:4 type B1 as required, superficial area n. exc. 150 sq. cm

M&L for 40 mm thick PCC 1:2:4 type B-1 using 20 mm graded stone aggregate as in floors, finishing cement concrete surface even & smooth with using extra cement. Note:- Glass dividing strips shall be measured and paid for separately as “ supply only”

Supply only glass dividing strips, 3 mm thick and 38 mm wide.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for (roof padding, flooring above ground floors) including roof treatment and removing from site all as specified and directed.

Taking down cement plaster, any description on brick, concrete or stone walls or ceiling including racking out joints, hacking for key, scrubbing down with water etc. (over roof) including roof treatment of any description and removal of rubbish off all as specified and directed.

M&L for cement concrete 1:2:4 type B-0 mix (12.5 mm graded stone aggregate) in padding over roof.

M&L for 20 mm thick rendering in CM 1:4 over concrete surfaces (Roof) mixed with liquid water proofing compound @ 0.200 litre per bag of 50 kg of cement complete all as specified. NOTE : Liquid water proofing compound shall be measured and paid for separately as “Supply only”

M&L for applying roof treatment on top of roof with APP modified membrane (minimum 3 mm thick) weight not less than 3.60 Kg/sqm and reinforced with non-woven polyster reinforcement/mat (centre core) with thermal insulation with white mineral gravel finish on upper side of membrane laid by torch application method with overlaps 150 mm on length side and 100 mm on the width side as per manufacturer’s instructions over a coat of approved cold applied bituminous oil based primer (IS- 3384) @ 250 gm/sqm complete all as specified and as directed by Engineer-in-Charge.

Supply only liquid water proofing compound.

M&L for kota stone slab 18-20 mm thick in riser of steps, skirting, dado and pillar laid over and including 10 mm thick rendering in CM 1:4 on brick work or concrete surfaces and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete.

Taking down shutters of any description exc. 1 sqm and n. exc. 2 sqm each and removing from site.

S&F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded wood grain printed PVC ‘C’ channel having a PVC sheet strip of 20 mm width struck inside with solvent cement for stiles and wood grain printed PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail. Panelling of wood grain printed PVC sheet to be fitted in the M.S. frame welded/sealed to the stiles & rails with 5 mm thick x 15 mm wide PVC sheet beading used inside stiles and rails and decorative PVC brading of 10 mm x 10 mm (90°) and joined together with solvent cement, and fixing in the frame at site as per specification & drawing.

S&F 35mm thick H.D.F prelaminated (Wenga/Teak colour) moulded shutter 35 mm thick puf (poly urathane foam) insulation with minium density 40kg/cum filled in between two HDF sheets of thickness 3.2 mm both & border covered with 10 mm thick PVC sheet as per Drg No. CEPZ/TD-378/Sheet 1/1 dated 27/12/2011

M&L 35 mm thick single piece factory made wire gauge door shutter of ( steel & aluminium XPM) manufacturing by PVC sheets printed 5 mm thick on both side on frame made out of M.S. tube 19 SWG, size 19x19 mm complete in all respect with lock rail & beautified by PVC beading all around fixed with PVC solvent cement complete as per Drg No. CEPZ/TD-378/Sheet 1/1 dated 27/12/2011

S&F stainless steel wire cloth, 0.36 nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples or wooden beads supplied with shutters.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing from site and rubbish off the premises.

M&L for vitrified ceramic light shade tiles 10 mm thick(square/rectangular) polished, area of each tile n. exc.0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed or bedding layer in CM 1:6.

M&L for glazed ceramic tiles, coloured, 350x250x7mm/450x300x7mm thick on vertical surfaces such as skirtings, dados and risers to steps etc, set & jointed in neat cement slurry & pointed in white or coloured cement to match over and including 10mm thick rendering in CM 1:4 on brick or concrete surfaces.

S&F in repair brass chromium plated shower rose with arm of 150x150 mm size with swivel joint including fixing to steel pipe or union.

S&F in repairs, vitreous china wash down water closet pan (pedestal pattern), white, with and including plastic water closet seat, white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device, and fixed complete all as specified.

S&F in repairs CP pressure jet for EWC, with 1.50 m tube fixed to angular stop cock.

S&F in repairs brass chromium plated toilet paper holder with flap fixed with chromium plated screw and PVC cleat fixed etc. complete all as specified and directed.

S&F in repairs PVC valveless, syphonic action type, flushing cistern, low level, 10 litres capacity, white, with inlet, ball valve, float and handle including brackets and PVC flushing pipe, 32 mm dia.

S&F in repairs 15 mm bore brass CP mixer for mixing hot and cold water screwed down for iron pipe.

S&F 75 mm bore cast iron bends (any radius), diminishing pieces or tapers (larger bore measured).

S&F 50 mm bore CI cowl.

M&L for 75 mm thick cement concrete 1:3:6 type C-2 using 40 mm graded stone aggregate in sub base.

S&F 60 mm thick, M-35 grade, coloured (red/yellow) glossy finish, machine pressed PCC interlocking paver block, with grey cement and pigment, any shape and size laid dry over and including 50 mm thick screened river washed sand cushion.

M&L for PCC 1:2:4 type B1 using 20 mm stone aggregate in kerbs of interlocking tiles and the like as directed.

S&F in repairs 25 mm bore prepolished stainless steel powder coated, single curtain rod (wall thickness not less than 1mm) including fancy type PVC powder coated brackets, funnels etc suitable for single curtain rod, fixed in repair, etc complete all as specified and approved by GE.

Demolition of brick work or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc. and removing from site all as specified and directed.

M&L for brick work with fly ash bricks, old size bricks, straight or curved on plan exc 6 mtr mean radius built in CM (1:6) all as spd and directed

S&f rubber lining fitted with aluminium powder coated strip 100 mm wide for door cill complete all as directed.

Dismantling AC/steel/fibre glass sheets (corrugated, semi corrugated, etc.) sheets in roof coverings.

S&F pre-painted galvatume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 MPa as in roof covering/cladding to wall, fixed with self tapping screws as specified.

S&F prepolished stainless steel peg set with 6 hooks of minimum size 375x40x8 mm fixed to doors/wall with machine screws.

Taking down carefully aluminium/copper point wiring (light, fan, socket or power) complete, including fixtures and fittings such as switches, ceiling roses, pendent, regulators, sockets, bell push, bell, light fittings etc. removing serviceable materials to store for keeping in safe custody for reuse at site or for taking credit (Credit shall be made as per Schedule of credit), removing rubbish from the site and making good all disturbed surfaces of walls, floors etc. to match to the existing surfaces.

M&L for modular point wiring complete with 1.5 Sq mm single core PVC insulated but unsheathed multistranded copper conductor FRLS cable 1100 volts grade drawn through and including non metallic rigid PVC heavy duty concealed conduit with wall thickness not less than 1.8 mm including conduit accessories like bends, tees junction boxes, etc fixed concealed/recessed in wall or ceiling etc including 1.5 Sq mm, single core, PVC insulated but unsheathed multi stranded copper conductor FRLS cable 1100 Volts grade as earth continuity wire connected to earth dolly including inner and outer frame plate matching with surrouding with modular sunken steel boxes zinc oxide plated of suitable size including modular sheets of suitable module and back plates etc. complete for:- (a) One light/fan point controlled by one, one way switch.

All as per item No. 112.00 above but One 3 pin 5 or 6 Amps socket outlet on independent board with other switches as directed.

All as per item No. 112.00 above but One 3 pin 5 or 6 Amps socket outlet on same board with other switches as directed.

M&L for modular point wiring complete with 2.5 Sq mm single core PVC insulated but unsheathed multistranded copper conductor FRLS cable 1100 volts grade drawn through and including non metallic rigid PVC heavy duty concealed conduit with wall thickness not less than 1.8 mm including conduit accessories like bends, tees junction boxes, etc fixed concealed/recessed in wall or ceiling etc including 2.5 Sq mm, single core, PVC insulated but unsheathed multi stranded copper conductor FRLS cable 1100 Volts grade as earth continuity wire connected to earth dolly including inner and outer frame plate matching with surrouding with modular sunken steel boxes zinc oxide plated of suitable size including modular sheets of suitable module and back plates etc. complete for one 3 pin 15 or 16 Amps socket outlet on independent board.

S&F modular switch 1 way 6 Amp, 1 module complete all as specified and directed.

S&F modular switch 1 way 16 Amp, 1 module complete all as specified and directed.

S&F modular socket 6 Amp, 2/3 pin mutipurpose 2 module complete all as specified and directed.

S&F modular socket 6 Amp/16 Amp, 6 pin multi purpose 2 module complete all as specified and directed.

S&F lamp holder insulated body with back plate for batten fittings polycarbonate body all as specified and directed by Engineer-in-Charge.

S&F ceiling rose surface bakelite 3 terminals 230 Volts AC with polycarbonate body all as specified and directed by Engineer-in-Charge.

Surface mounted 1x20 watt LED tube light fittings (4 feet long), prewired, decorative luminaire with inbuilt LED tube rod and acrylic cover with all accessories and making connection using 3 core, 0.50 Sqmm PVC insulated and overall sheathed flexible copper conductor cable from ceiling rose/PVC connector to light fitting and testing etc complete all as specified and directed.

Surface mounted 1x10 watt LED tube light fittings, prewired, decorative luminaire with inbuilt LED tube rod and acrylic cover with all accessories and making connection using 3 core, 0.50 Sqmm PVC insulated and overall sheathed flexible copper conductor cable from ceiling rose/PVC connector to light fitting and testing etc complete all as specified and directed.

Supply and fixing as in repair bulk head 10 W LED light fitting IP 43 in engineering plastic housing with clear primatic diffuser conf to Cat Pt No CG80IB6WLED of C&G or equivalent of make /Philips/Wipro/Bajaj complete with all acessories , connecting electricaly to ceiling rose using cord flexible 3 core PVC insulated over all sheathed with flexible copper conductor of size 0.75 sqmm all as required.

S&F in repair and testing factory made sheet metal enclosure for MCB DB SPN 8 way 240 volt with single door, IP - 43 protection duly fixed/concealed in wall complete and making good disturbed surfaces of wall, floor etc including necessary connection lugging with copper lugs pin/ring type all as directed by Engineer-in-Charge.

S&F in repair MCB single pole 230 volts any rating from 6 to 32 amps, with rupturing capacity 10 KA, 'C' curve type, including providing thimble for out going cables.

S&F in repair MCB single pole and neutral 240 volts any rating from 6 to 32 amps, with rupturing capacity 10 KA, 'C' curve type, including providing thimble for out going cables.

M&L in repair for earthing complete with galvanised steel earth electrode 60cmx60cmx6mm buried directly in ground vertically to depth not less than 2.25m below normal ground level with top edge of the earth plate at a depth not less than 1.5m below ground level connected to and including GI earth lead wire 4 mm dia by means of nuts, bolts, check nuts and washer etc, made of GI and connected to test point and earth dolly all as shown in electrical plate No. 3 SSR Part-I 2009 and specified or indicated including excavation and earthwork in any type of soil PCC (1:3:6) Type C1 in chamber, precast RCC 50 mm thick in cement concrete (1:2:4) type B1, reinforced with welded steel wire fabric or XPM (Weight not less than 4.00 Kg/Square metre) with cast iron frame, funnel with wire mesh, 20mm bore medium grade GI watering pipe, lugs, 15mm bore medium grade GI protection pipe, test point etc. complete all as specified and directed. Note:- (i) Item includes the cost of 7.5 metre GI pipe for protection of earth lead. (ii) Item includes the cost of 7.5 metre GI earth lead.

S&F LED lamp 12 watts

Excavating in trenches in any type of soil, n. exc. 1.5 m wide and n. exc. 1.5 m in depth, for foundation, etc. or for shafts, wells, cess pits, manholes, pier holes, etc n. exc. 10 sqm on plan and n.exc 1.5 m in depth and getting out.

Returning, filling in (soil), including spreading, leveling, watering and well ramming in layers not exc. 25 cm.

Removing excavated material (soil) n.exc. 50 m and depositing where directed at a level n. exc. 1.5 m above the starting point.

Supply and lay in trenches/on wall/on pole/in duct /through protection pipe, XLPE insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables heavy duty LT cable, 1100 volts grade with aluminium conductor cross sectional area 16 Sqmm 2 core size including retrieving/taking out/taking down old unserviceable cable from duct/trenches/pipes/pole/wall etc. including brick cover and protection pipe and disconnecting the connections. Note :- Excavation and earth work, sand cushioning, brick cover and protection pipe etc. shall be measured and paid for separately.

M&L for dry clean fine river sand as in sand cushioning to underground cable including punning down of sand layer all as specified and directed. Note :- Punned thickness shall only be measured and paid.

M&L for brick protection with sub class 'B' old size brick well burnt laid flat for cable protection abutting each other laid dry with width equal to length of brick complete all as specified and directed.

M&L for galvanised steel tubing, light grade, for protection of cable, laid in trenches/road crossing/floor or fixed to pole/wall with all fittings, of size 40 mm bore.

M&L for point wiring complete with 1.5 Sq mm single core PVC insulated but unsheathed multistranded copper conductor FRLS cable 1100 volts grade drawn through and including non metallic rigid PVC heavy duty conduit on surface with wall thickness not less than 1.8 mm including conduit accessories like bends, tees junction boxes, etc fixed concealed/recessed in wall or ceiling etc including 1.5 Sq mm, single core, PVC insulated but unsheathed multi stranded copper conductor FRLS cable 1100 Volts grade as earth continuity wire including sunken type pressed steel terminal boxes of suitable size with 3mm thick bakelite sheet white/coloured top cover for:- (a) One light/fan point controlled by one, one way switch.

All as per item No. 137.00 above but one 3 pin 5 or 6 Amps socket outlet on independent board with other switches as directed.

All as per item No. 137.00 above but one 3 pin 5 or 6 Amps socket outlet on same board with other switches as directed.

M&L for point wiring complete with 2.5 Sqmm single core PVC insulated but unsheathed multistranded copper conductor FRLS cable 1100 volts grade drawn through and including non metallic rigid PVC heavy duty conduit on surface with wall thickness not less than 1. 8mm heavy duty including conduit accessories concealed in wall, ceiling etc including sunken type pressed steel terminal boxes of size 175/100mm with 3mm thick bakelite sheet cover white/coloured including 2.5 Sqmm, single core, PVC insulated but unsheathed copper conductor FRLS 1100 volts grade cable as earth continuity wire for one 3 pin 15 or 16 Amps socket outlet on independent board.

S&F switch piano flush button single pole one way 6 amps 230 volts AC with polycarbonate body all as specified and directed by Engineer-in-Charge.

S&F switch piano flush button single pole one way 16 amps 230 volts AC with polycarbonate body all as specified and directed by Engineer-in-Charge.

S&F socket out let, 5 pin 6 amps multi purpose 2 in 1 flush type, 230 volts AC with polycarbonate body all as specified and directed by Engineer-in-Charge.

S&F socket out let, 6 pin 6 & 16 amps multi purpose 2 in 1 flush type, 230 volts AC with polycarbonate body all as specified and directed by Engineer-in-Charge.

S&F fan regulator electronic, switch type hum free with polycarbonate body suitable to control speed of fan from 0 to 100% and connecting electrically all as specified and directed by Engineer-in-Charge.

M&L in repair for sub main wiring with two runs of PVC insulated but unsheathed multi stranded copper conductor FRLS cable 1100 volt grade of size 6 Sqmm and one run of 6 Sqmm single core PVC insulated but unsheathed multi stranded copper conductor FRLS cable 1100 volt grade as earth lead drawn through in and including non metallic PVC conduit of size 25 mm dia (external) with wall thickness not less than 1.8 mm, ISI marked on surface on wall/ceiling including accessories like bends, tees junction boxes, etc fixed in wall or ceiling etc. complete as directed by Engineer-in-Charge. NOTE: Two runs of cable with one run of earth wire and PVC conduit shall be measured & paid for as one length.

M&L for taking down ceiling fan and hanging the same after repair and connecting up including provision of cable from ceiling rose or connector to fan.

Note:- Cutting chases in walls/floors/ceilings wherever required for electric work shall be deemed to be included in respective item of Schedule ‘A’.

A V BUILDERS

M/s. RAMESH KUMAR

RD Engineers

Raghbir chand

M/S J N TRADERS

dadwal engineers