Construction of Executive Hostel (EH) Building for Integrated township at Chandrapura, Jharkhand

ABSTRACT OF COST CIVIL WORK

Sr No Sub Head DSR Amount Non DSR Amount Total Amount

Sr No Sub Head DSR Amount Non DSR Amount Total Amount

3 Reinforced Cement Concrete 104145766 0.00 104145765.6

11 Dismantling & Demolishing Work 756310.2 0.0 756310.17

12 Aluminium Work&other 763858.60 0.00 763858.60

14 Structural Glazing Work 9665381.02 0.00 9665381.02

15 Miscellaneous Work 0.00 4981786.00 4981786.00

Total Executive Building (civil work) 261689143.65 5834836.06 267523979.71

CONSTRUCTION OF INTEGRATED TOWNSHIP AT CHANDRAPURA, JHARKHAND

ESTIMATE - EXECUTIVE HOSTEL

2023 with Non DSR

Sl.No. DSR 2023 Description Unit Quantity DSR Amount

I 2.0 EARTH WORK

Carriage of materials by Mechanical Transport including loading, unloading and stacking of

Earth up to 5 km

Earth work in excavation by mechanical means {Hydraulic excavator)/ manual means over

areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting

out and disposal of excavated earth lead upto 50 m and for all lift, as directed by Engineer-in-

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc.

3 2.25 in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and cum 5064.37 209.78 1062396.81

watering, lead up to 50 m and lift up to 1.5 m.

Excavating, supplying, stacking and filling of local earth (including royalty) by mechanical

transport upto a lead of 5km also including ramming and watering of the earth in layers not

exceeding 20 cm in foundation trenches, plinth, sides offoundation etc. complete for all lift.

Supplying and filling in plinth with sand under floors, including watering, ramming,

consolidating and dressing complete.

Surface dressing of the ground including removing vegetation and inequalities not exceeding

15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m.

ANTI-TERMITE TREATMENT

Providing Pre-constructional anti- termite treatment and creating a chemical barrier to the

building by injecting chemical emulsion of required concentrations under grade slab and

Grade beam, all around the footings, column pits, trenches, pits, tunnels, wall trenches, back

fill, plinth filling, junction of wall and floor, Retaining / side walls of basement floor, external

perimeter of building, surrounding of pipes, expansion joints, below UG sump and Retaining /

side walls etc.as per instructions of chemical manufacturer and all as directed. The treatment

shall be carried out strictly in accordance with the technical specification and conforming to

IS 6313 or equivalent BS specification. The chemical to be used as insecticides for the

7 MR treatment shall be 50% EC (Imdachloropid 30.5 SC)and the application shall be dilute one

part of chemical 50% EC with 49 parts of water to get 1% emulsion and strictly in accordance

with the manufacturer's specification, as specified by consultants appointed by the

contractor. Manufacturer should ensure the performance guarantee of the work for a period

of 10 years by submitting a BG for 5(Five)% value of total anti-termite treatment work, for a

period of 05 years and Corporate Guarantee for further 05 (Five) Years.

The bottom surface of the excavations made for Foundation, column pits and trenches shall

7.1 a be treated with the chemical emulsion mentioned above at @ 5 litres/ sq. meter of surface sqm 3509.05 221.00 775500.05

The Vertical surface of sub structure (Retaining wall,foundations etc.) shall be treated @ 7.5

litres/ sq. meter of vertical surface area in contract with back fill soil.

TOTAL EARTH WORK AMOUNT 3150829.00 853050.06

II 4.0 CONCRETE WORK

Providing and laying in position cement concrete of specified grade excluding the cost of

centering and shuttering - All work up to plinth level :

1:3:6 (1 Cement : 3 coarse sand (zone-Ill) derived from natural sources :6 graded stone

8.1 4.1.6 aggregate 40 mm nominal size derived from natural sources) cum 449.98 7683.42 3457404.53

9 4.3 Centering and shuttering including strutting, propping etc. and removal of form work for :

9.1 4.3.1 Foundations, footings, bases for columns sqm 101.70 419.72 42685.76

Providing and laying damp-proof course 50 mm thick with cement concrete 1:2:4 (1 cement:

10 4.11 2 coarse sand (zone-Ill) derived from natural sources: 4 graded stone aggregate 20 mm sqm 192.98 530.60 102394.25

nominal size derived from natural sources).

Extra for providing and mixing water proofing material in cement concrete work in doses by 50kg

weight of cement as per manufacturer's specification. cement

Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of approved

12 4.13 quality using 1.7 kg per square metre on damp proof course after cleaning the surface with sqm 192.98 156.42 30186.42

brushes and finally with a piece of cloth lightly soaked in kerosene oil.

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand

(zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size

13 4.17 derived from natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, sqm 216.00 801.98 173226.77

well rammed and consolidated and grouted with fine sand, including necessary excavation,

levelling & dressing & finishing the top smooth.

TOTAL CONCRETE WORK AMOUNT 3807097.33

III 5.0 REINFORCED CEMENT CONCRETE

14.1 5.9 Centering and shuttering including strutting, propping etc. and removal of form for :

14.2 5.9.1 Foundations, footings, bases of columns, etc. for mass concrete SQM. 617.03 419.718145 258980.3659

14.3 5.9.2 Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc. SQM. 266.68 901.72775

14.4 5.9.3 Suspended floors, roofs, landings, balconies and access platform SQM. 8130.46 992.435675 8068958.558

14.6 5.9.5 Lintels, beams, plinth beams, girders, bressumers and cantilevers SQM. 9584.26 788.16892 7554012.622

14.7 5.9.6 Columns, Pillars, Piers, Abutments, Posts and Struts SQM. 6006.06 1028.87939 6179511.349

14.8 5.9.7 Stairs, (excluding landings) except spiral-staircases SQM. 338.09 818.725985 276805.916

Small lintels not exceeding 1.5 m clear span, moulding as in cornices, window sills, string 136752.566

courses, bands, copings, bed plates, anchor blocks and the like

Edges of slabs and breaks in floors and walls Under 20 cm wide SQM. 2450.00

14.11 5.9.19 Weather shade, Chajjas, corbels etc., including edges SQM. 348 1017.96 353945.5021

Extra for additional height in centering, shuttering where ever required with adequate bracing,

propping etc., including cost of de-shuttering and decentering at all levels, over a height of

3.5 m, for every additional height of 1 metre or part thereof (Plan area to be measured).

15.1 5.11.1 Suspended floors, roofs, landing, beams and balconies (Plan area to be measured) sqm 411.32

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in

position and binding all complete upto plinth level.

16.1 5.22.6 Thermo-Mechanically Treated bars of grade Fe-500D or more. kg 51744.00 115.43 5972905.905

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in

position and binding all complete above plinth level.

17.1 5.22A.6 Thermo-Mechanically Treated bars of grade Fe-500D or more. kg 300967.0 115.43 34741179.1

18 5.30 Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections. metre 7680.00 83.91 644440.4736

Providing and laying in position ready mixed or site batched design mix cement concrete for

reinforced cement concrete work; using coarse aggregate and fine aggregate derived from

natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures

in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to

improve durability and workability without impairing strength; including pumping of concrete

to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering,

19 5.33 finishing and reinforcement as per direction of the engineer-in-charge; for the following

grades of concrete.

Note: Extra cement up to 10% of the minimum specified cement content in design mix shall

be payable separately. In case the cement content in design mix is more than 110% of the

specified minimum cement content, the contractor shall have discretion to either re-design

the mix or bear the cost of extra cement.

19.1 5.33.1 All works upto plinth level

a 5.33.1.1 Concrete of M25 grade with minimum cement content of 330 kg /cum cum 778.19 10172.93 7916475.451

19.2 5.33.2 All works above plinth level upto floor V level

a 5.33.2.1 Concrete of M25 grade with minimum cement content of 330 kg /cum cum 2804.73 10553.59 29599959.6

20 5.38 Extra for R.C.C./ B.M.C/ R.M.C. work above floor V level for each four floors or part thereof. cum 880.96 380.65 335339.3577

Add for using extra cement in the items of design mix over and above the specified cement

content therein.

Floor Joint 100mm Providing & Fixing of Expansion Joint system related with the Floor to

Floor/ Floor to Wall Expansion Joint Cover for 100 mm Expansion Joints Aluminium Covers

Profiles, having a Hard Wearing, Maintenance Free, long Lasting design. The surface of the

Exp. Joint Covers should have Serrated Surface for Skid Resistance and should be ADA

Compliant. The exposed surface should not exceed 113mm.The design of the Exp. Joint

Cover System should be such that it should avoid any accumulation of dirt. The Exp. Joint

21 5.44 Cover should have an Articulated Telescope Design so as to accommodate the movements

in 3 directions. The system should be in alloy 6063 T66 in Mill finish and the total exposed

surface of the profile should not be more than 113 & the installation Height can be of 35 mm.

The system can be used for standard Rolling loads of private Cars or Cart wheel loads. The

system should have ASTM1399 E certification. The extrusion should be as ASTM 6063 T66

standards. The System shall be such that it will be flushed with the finish The System should

be ASTM-E 1399. Provision of Moiser Barrier in the Joint System to have watertight joint is

mandatory requirement all as per the manufactures design and as approved by the Engineer-

in-Charge. Approved Make: Cameo Inc (Migua) Or equivalent/ approved list of Make

21.1 5.44.1 Floor Joint of 100 mm gap metre 6841.95

Providing & Fixing of Expansion Joint system related with the WALL to WALL (Internal /

External) Location as per drawing and direction of engineer –In- Charge. Expansion Joint The

design of the Joint Cover System should be such that the system should snap onto a 50mm

22 5.45 wide, hook shaped aluminum clip. The system should have gasket seals on the edges to

provide scratch protection to the wall finish and prevent accumulation of dust. The system

should be in 6063 alloy in clear anodized matt finish. Provision of Moisture Barrier Membrane

in the Joint System to have watertight joint is mandatory requirement for all external area as

per the manufactures design and as approved by the Engineer-in-Charge. Approved Make:

Cameo Inc Or equivalent/ approved list of Make

22.1 5.45.1 Wall Joint of 100 mm gap metre 5678.64

Providing and fixing of expansion joint system of approved make and Manufactures for

various roof locations as per approved drawings and Direction of Engineer-In-Charge. The

joints shall be of extruded aluminium base members with, self aligning and self centring

arrangement support plates as per ASTM B221-02. The system shall be such that it

provides watertight roof to roof/roof to corner joint cover expansion control system that is

capable of accommodating multidirectional seismic movement without stress to its

components. System shall consist of metal profile that incorporates a universal aluminium

base member designed to Accommodate various project conditions and roof treatments.

The cover plate shall be designed of width and thickness required to satisfy movement and

23 5.46 loading requirements and secured to base members by utilizing manufacturer’s pre-

engineered self-centring arrangement that freely rotates / moves in all directions. The Self

centring arrangement shall exhibit circular sphere ends that lock and slide inside the

corresponding aluminium extrusion cavity to allow freedom of movement and flexure in all

directions including vertical displacement. The Joint System shall resists damage or

deterioration from the impact of falling ice, exposure to UV, airborne contaminants and

occasional foot traffic from maintenance personnel. Provision of Moisture Barrier Membrane

in the Joint System to have water tight joint is mandatory requirement. (Material shall

confirm to ASTM 6063

23.1 5.46.1 Roof Joint of 100 mm gap metre 6406.49

TOTAL REINFORCED CEMENT CONCRETE AMOUNT 104145765.59

IV 6.0 MASONRY WORK

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in

24 6.1 foundation and plinth in:

24.1 6.1.2 Cement mortar 1:6 (1 cement : 6 coarse sand) cum 51.34 7633.65 391911.446

Providing and laying Autoclaved Aerated concrete(AAC) blocks masonry 100 mm/ 125 mm

25 6.38 thick with Grade-1 AAC blocks of density 551 to 650 kg/cum conforming to 15:2185 (Part 3) cum 184.42 10912.19 2012426

in super structure above plinth level up to floor V level in cement mortar 1:4 (1 cement :4

coarse sand ). The rate includes providing and placing in position 2 Nos 6 mm dia M.S. bars

Providing and laying Autoclaved Aerated concrete(AAC) blocks masonry with 150 mm to 300

mm thick with Grade-1 AAC blocks of density 551 to 650 kg/cum conforming to 15:2185 (Part

3) in super structure above plinth level up to floor V level with RCC band at sill level and lintel

level with approved block laying polymer modified adhesive mortar all complete as per

direction of Engineer-in-Charge. (The payment of RCC band and reinforcement shall be

made for separately).

Extra for brick work / AAC block masonry / Tile brick masonry in superstructure above floor V

level, for each four floors or part thereof by mechanical means.

TOTAL MASONRY WORK AMOUNT 22559114.58

V 8.0 CLADDING WORK

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished,

machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations

of required size, approved shade, colour and texture laid over 20 mm thick base cement

mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching

pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give

high gloss finish etc. complete at all levels.

28.1 8.2.2 Granite stone slab colour black, Cherry/Ruby red

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including

29 8.3 machine polishing to edge to give high gloss finish etc. complete as per design approved by

Engineer-in-Charge.

Extra for fixing marble /granite stone, over and above corresponding basic item, in facia and

30 8.4 drops of width upto 150 mm with epoxy resin based adhesive, including cleaning etc. metre 710.04 608.52 432072.88

Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen

platform, vanity counter and similar location in marble/ Granite/ stone work, including

31 8.5 necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges each 174.00 1047.50 182265.45

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to

be specified by the manufacturer), of approved make, in all colours, shades except burgundy,

bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps

32 8.31 and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and sqm 12154.21 1357.09 16494321.70

jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed

with pigment of matching shade complete.

Stone tile work for wall lining upto 10 m height with special adhesive over 12 mm thick bed of

33 7.38 cement mortar 1:3 (1 cement : 3 coarse sand), including pointing in white cement with an

admixture of pigment to match the stone shade.

33.1 7.38.1 8 mm thick (mirror polished and machine cut edge)

34.1.1 7.38.1.1 Granite stone of any colour and shade sqm 3312.10

TOTAL CLADDING WORK AMOUNT 19030179.27

VI 9.0 WOOD AND P. V. C. WORK

Providing and fixing ISi marked flush door shutters conforming to IS : 2202 (Part I) non-

decorative type, core of block board construction with frame of 1st class hard wood and well

matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on

both faces of shutters:

33.1 9.21.2 30 mm thick including ISi marked Stainless Steel butt hinges with necessary screws sqm 727.20 2324.80 1690593.56

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all

edges of flush door shutters (over all area of door shutter to be measured).

Extra for providing vision panel not exceeding 0.1 sqm in all type of flush doors (cost of glass

excluded) (overall area of door shutter to be measured):

35.1 9.24.1 Rectangular or square sqm 36.36 213.15 7750.14

Extra for cutting rebate in flush door shutters (Total area of the shutter to be measured).

Providing and fixing aluminium extruded section body tubular type universal hydraulic door

closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg

to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with

necessary accessories and screws etc. complete.

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less

38 9.97 than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with

necessary screws etc. complete :

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than

39 9.100 grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with

necessary screws etc. complete :

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic

40 9.101 coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour

and shade, with necessary screws etc. complete.

40.1 9.101.2 Twin rubber stopper each 394.00 77.44 30509.86

Providing and fixing ISI marked aluminium sliding door bolts anodised (anodic coating not

less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with

necessary screws etc. complete.

Providing and fixing bright finished brass 100 mm mortice latch and lock, ISi marked, with six

levers and a pair of anodised (anodic coating not less than grade AC 10 as per IS : 1868)

aluminium lever handles of approved quality with necessary screws etc. complete.

Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss /

matt/ suede finish with high density protective surface layer and reverse side of adhesive

bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved

Providing and fixing panic bar/ latch (Double point) fitted with a single body, Trim Latch &

44 9.139 Lock on back side of the Panic Latch of reputed brand and manufacture to be approved by each 134.00 8954.29 1199874.91

the Engineer- in- charge, all complete.

Providing and fixing fire resistant door frame of section 50 x 60 mm on horizontal side & 35 x

60 mm on vertical sides having built in rebate made out of 1.6 mm thick GI sheet (Zinc

coating not less than 120 gm/sqm) suitable for mounting 120 minutes Fire Rated Glazed

Door Shutters. The frame shall be filled with mineral wool Insulation having density minimum

96Kg/sqm. The frame will have a provision of G.I. anchor fastners 14 nos (5 each on vertical

45 9.161 style & 4 on horizontal style of size M10 x 80) suitable for fixing in the opening along with metre 393.20 2357.76 927072.75

factory made template for SS ball bearing hinges of size 100x89x3 mm for fixing of fire rated

glazed shutter. The frame shall be finished with an approved fire resistant primer or powder

coating of not less than 30 micron in desired shade as per the directions of Engineer - in-

Charge. (Cost of SS ball bearing hinges is excluded).

Providing and fixing 60 mm thick glazed fire resistant door shutters of 120 minutes Fire rating

conforming to IS:3614 (Part II) or EN1634-1:1999, tested and certified as per laboratory

approved by Engineer-in-Charge, with suitable mounting on door frame, consisting of vertical

styles, top rail & side rail 60 mm x 60 mm wide and bottom rail of 110 mm x 60 mm made out

of 1.6 mm thick G.I. sheet (zinc coating not less than 120 gm/ sqm) duly filled mineral wool

46 9.162 insulation having density minimum 96 kg/ cum and fixing with necessary stainless steel ball sqm 204.00 12862.76 2624002.71

bearing hinges of size 100x89x3 mm of approved make, including applying a coat of

approved fire resistant primer or powder coating not less than 30 micron etc all complete as

per direction of Engineer-in-Charge (panelling to be paid for separately).

Providing and fixing glazing in fire resistant door shutters, fixed panels & partitions etc., with

G.I. beading made out of 1.6 mm thick G.I. sheet (zinc coating not less than 120 gm/sqm) of

size 20 x 33 mm screwed with M4 x 38 mm SS screws at distance 75 mm from the edges

and 150 mm c/c , including applying a coat of approved fire resistant primer/ powder coating

of not less than 30 micron on G.I. beading, & special ceramic tape of 5 x 20 mm size etc

complete in all respect as per NBC 2016, IS 16231 (Part 3):2016 and as per direction of

Engineer-in-Charge with glass of required thickness having 120 minutes of fire resistance

47 9.164 both integrity & radiation control (EW120) and minimum 20 minutes of insulation (El20). The sqm 153.00 46748.19 7152472.89

manufacturer have to give test report/certification of fire glass and the glass should have the

stamp showing the value of E, EW & El. The glass shall be tested in approved NABL

accredited lab or by any other accreditation body which operates in accordance with ISO/IEC

17011 and accredited labs as per ISO/IEC 17025 for testing and

calibration scopes shall be eligible. The maximum glazing size shall not be more than

1100x2200 mm (w x h) or 2.42 sqm.

Providing and fixing bright /matt finished Stainless Steel handles of approved quality & make

with necessary screws etc all complete.

Providing and fixing factory made single extruded WPC (Wood PolymerComposite) solid

door/window/Clerestory windows & other Frames/ Chowkhat comprising of virgin PVC

polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood

powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100

gms) fabricated with miter joints after applying PVC solvent cement and screwed with full

body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw

withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58

N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class A

category with property of being termite/borer proof, water/moisture proof and fire retardant

and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length

complete as per direction of Engineer-In- Charge. (M.S hold fast/lugs or SS dash fasteners

shall be paid for separately). Note: For WPC solid door/fwindow frames, minus 5 mm

tolerance in dimensions i.e depth and width of profile shall be acceptable. Variation in profile

dimensions on plus side shall be acceptable but no extra payment on this account shall be

TOTAL WOOD AND P. V. C. WORK AMOUNT 18088005.64

VII 10.0 STEEL WORK

Supplying and fixing rolling shutters of approved make, made of required size M.S. laths,

interlocked together through their entire length and jointed together at the end by end locks,

mounted on specially designed pipe shaft with brackets, side guides and arrangements for

50 10.6 inside and outside locking with push and pull operation complete, including the cost of

providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile

steel wire of adequate strength conforming to IS: 4454 - part 1and M.S. top cover of required

thickness for rolling shutters.

50.1 10.6.1 80x1.25 mm M.S. laths with 1.25 mm thick top cover sqm 3910.02

51 10.7 Providing and fixing ball bearing for rolling shutters. each 526.96

Providing and fixing carbon steel galvanised ( minimum coating 5 micron) dash fastener of 10

mm dia double threaded 6.8 grade (yield strength 480 N/mm2), counter sunk head,

comprising of 10 mm dia polyamide PA 6 grade sleeve, including drilling of hole in frame ,

concrete/ masonry, etc. as per direction of Engineer-in-charge.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc.,

53 10.16 including cutting, hoisting, fixing in position and applying a priming coat of approved steel

primer, including welding and bolted with special shaped washers etc. complete.

53.1 10.16.2 Hot finished seamless type tubes kg 220.86

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels,

plates etc., including welding, grinding, buffing, polishing and making curvature (wherever

required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c

fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel

54 10.28 bolts etc., of required size, on the top of the floor or the side of waist slab with suitable kg 1790.48 826.70 1480189.31

arrangement as per approval of Engineer-incharge, (for payment purpose only weight of

stainless steel members shall be considered excluding fixing accessories such as nuts, bolts,

fasteners etc.).

TOTAL STEEL WORK AMOUNT 1854605.94

VIII 11.0 FLOORING WORK

52 mm thick cement concrete flooring with concrete hardener topping, under layer 40 mm

thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm

nominal size) and top layer 12 mm thick cement hardener consisting of mix 1:2 (1 cement

55 11.4 hardener mix : 2 graded stone aggregate 6 mm nominal size) by volume, hardening sqm 1547.15 1047.24 1620227.85

compound mixed @ 2 litre per 50 kg of cement or as per manufacturer's specifications. This

includes cost of cement slurry, but excluding the cost of nosing of steps etc. complete.

Cement plaster skirting up to 30 cm height, with cement mortar 1:3 (1 cement :3 coarse

sand), finished with a floating coat of neat cement.

Providing and laying matt finished vitrified tile of size 300x300x9.8 mm having with water

absorption less than 0.5% and conforming to IS: 15622 of approved make in all colours and

shades in for outdoor floors such as footpath, court yard, multi modals location etc., laid on

20 mm thick base of cement mortar 1:4 (1 cement : 4 coarse sand) in all shapes & patterns

including grouting the joints with white cement mixed with matching pigments etc. complete

as per direction of Engineer-in-Charge.

58 11.24 Extra for pre finished nosing to treads of steps of marble/granite stone. metre 350.00 770.51 269678.14

Extra for marble/granite stone flooring in treads of steps and risers using single length up to

Kata stone slab flooring over 20 mm (average) thick base laid over and jointed with grey

60 11.26 cement slurry mixed with pigment to match the shade of the slab, including rubbing and

polishing complete with base of cement mortar 1 :4 (1 cement: 4 coarse sand):

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm

(average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement

slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified

by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours

62 11.37 such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 sqm 31.05 1173.64 36441.44

Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing

the joints with white cement and matching pigment etc., complete.

38 mm thick wood block flooring of first class teak wood laid over 25 mm thick leveling layer

of cement concrete 1:2:4 (1 cement : 2 coarse sand: 4 graded stone aggregate 10 mm

63 11.34 nominal size) to be paid separately, coated with a thin layer of hot bitumen penetration 80/25 SQM 267.84 12865.49 3445892.21

(blown type) @ 2.45 kg per sgm, including fixing blocks in position after dipping in hot

bitumen (blown type) up to half depth, planed, levelled smooth and finished complete.

Providing and laying double charge vitrified floor tiles in different sizes (thickness to be

specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:

15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4

(1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting

the joints with white cement and matching pigments etc., complete.

64.1 11.41A.1 Double charge vitrified tile polished finish of size

64.2 11.41A.3 Glazed Vitrified tiles Matt/Antiskid finish of size

Providing and laying double charge vitrified tiles in different sizes (thickness to be

specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S.

65 11.46 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick

bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3

kg/ sqm including grouting the joint with white cement & matching pigments etc. complete.

Providing and laying Polished Granite stone flooring in required design and patterns, in linear

as well as curvilinear portions of the building all complete as per the architectural drawings

with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1

cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement

slurry admixed with pigment of matching shade including rubbing, curing and polishing etc.

all complete as specified and as directed by the Engineer-in-Charge.

66.1 11.56.1 Polished Granite stone slab colour of Black, Cherry/Ruby Red or equivalent sqm 351.00 4796.34 1683513.72

TOTAL FLOORING WORK AMOUNT 14820802.18

IX 12.0 ROOFING WORK

Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone

67 12.21 aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement : 3

fine sand) as per standard design :

Providing and fixing false ceiling at all height including providing and fixing of frame work

made of special sections, power pressed from M.S. sheets and galvanized with zinc coating

of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25

mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one

flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts,

other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with

nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I.

channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the

ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each

having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular

to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long

G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high

68 12.45 having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with

the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval,

including fixing of gypsum board to ceiling section and perimeter channel with the help of dry

wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush

finish of tapered and square edges of the board with recommended jointing compound ,

jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both

sides of joint and two coats of primer suitable for board, all as per manufacturer's

specification and also including the cost of making openings for light fittings, grills, diffusers,

cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings,

specification and direction of the Engineer in Charge but excluding the cost of painting with :

12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011

(Board with BIS certification marks)

68.2 12.45.3 12.5 mm thick tapered edge gypsum moisture resistant board sqm 1682.03 1636.60 2752803.12

Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true

horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections

( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main "T" runner with

suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick

(minimum) sheet, spaced at 1200 mm center to center and cross "T" of size 24x25 mm made

of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main "T" at 600 mm

center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm

and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of

the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm

69 12.52 and laying false ceiling tiles of approved texture in the grid including, required cutting/making,

opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T"

runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm

fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods

with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to

center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted

with polyester paint, all complete for all heights as per specifications, drawings and as

directed by Engineer-in-charge.

12.5 mm thick fully Perforated Gypsum Board tile made from plasterboard having glass fibre

conforming to IS: 2095 part I, of size 595x595 mm, having perforation of 9.7x9.7 mm at 19.4

69.1 12.52.4 mm c/c with center borders of 48 mm and the side borders of 30 mm, backed with non sqm 372.60 1635.42 609356.90

woven tissue on the back side, having an NRC (Noise Reduction Coefficient) of 0.79, with 50

mm resin bonded glass wool backing.

Providing and Fixing 15mmthick densified tegular edged eco friendly light weight calcium

silicate false ceiling tiles of approved texture of size 595 x 595 mm in true horizontal level,

suspended on inter locking metal grid of hot dipped galvanised steel sections (galvanising@

120 grams per sqm including both side) consisting of main 'T runner suitably spaced at joints

to get required length and of size 24x38 mm made from 0.33 mm thick (minimum) sheet,

spaced 1200 mm centre to centre, and cross "T" of size 24x28 mm made out of 0.33 mm

(Minimum) sheet, 1200 mm long spaced between main'T' at 600 mm centre to centre to form

a grid of 1200x600 mm and secondary cross 'T' of length 600 mm and size 24 x28 mm made

of 0.33 mm thick (Minimum) sheet to be inter locked at middle of the 1200x 600 mm panel to

from grid of size 600x600 mm, resting on periphery walls /partitions on a Perimeter wall angle

pre-coated steel of size(24x24X3000 mm made of 0.40 mm thick (minimum) sheet with the

70 12.53 help of rawl plugs at 450 mm centre to centre with 25 mm long dry wall screws @ 230 mm

interval and laying 15 mm thick densified edges calicum silicate ceiling tiles of approved

texture in the grid, including, cutting/ making opening for services like diffusers, grills, light

fittings, fixtures, smoke detectors etc., wherever required. Main 'T' runners to be suspended

from ceiling using G.I. slotted cleats of size 25x35x1.6 mm fixed to ceiling with 12.5 mm dia

and 50 mm long dash fasteners, 4 mm G.I. adjustable rods with galvanised steel level clips

of size 85 x 30 x 0.8 mm, spaced at 1200 mm centre to centre along main 'T. Bottom

exposed with 24 mm of all T-sections shall be pre-painted with polyster baked paint, for all

heights, as per specifications, drawings and as directed by Engineer-in-Charge..

Note :- Only calcium silicate false ceiling area will be measured from wall to wall. No

deduction shall be made for exposed frames/opening (cut outs) having area less than 0.30

sqm.The calcium silicate ceiling tile shall have NRC value of 0.50 (Minimum), light eflection sqm 1348.96 2309.87 3115919.46

> 85%, non- combustible as per B.S. 476 part IV, 100% humidity resistance and also having

thermal conductivity <0.043 w/mK.

Providing and fixing Heat Resistant Terrace Tiles (300 mm x 300 mm x 20 mm) with SRI

(solar refractive index) > 78, solar reflection > 0.70 and initial emittance > 0.75 on waterproof

and sloped surface of terrace, laid on 20 mm thick cement sand mortar in the ratio of 1:4 (1

cement : 4 coarse sand) and grouting the joints with mix of white cement & marble powder in

ratio of 1:1, including rubbing and polishing of the surface upto 3 cuts complete, including

providing skirting upto 150 mm height along the parapet walls in the same manner.

TOTAL ROOFING WORK AMOUNT 14710409.21

X 13.0 FINISHING WORK

72 13.4 12 mm cement plaster of mix :

Extra for plastering exterior walls of height more than 10 m from ground level for every

73 13.22 additional height of 3 m or part thereof.

74 13.5 15 mm cement plaster on rough side of single or half brick wall of mix:

75 13.16 6 mm cement plaster of mix :

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to

prepare the surface even and smooth complete.

Painting with synthetic enamel paint of approved brand and manufacture to give an even

77.1 13.62.1 Two or more coats on new work sqm 10.00 242.16 2421.55

Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile

Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture,

including applying additional coats wherever required to achieve even shade and colour.

Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than

79 13.41 50 gram/litre, of approved manufacturer and of required shade and colour all complete to

achieve even shade and colour :

New work (two or more coats) over and including water thinnable priming coat with cement

primer having VOC content less than 50 gram/litre

80 13.45 Finishing walls with textured exterior paint of required shade :

New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of

exterior primer applied @ 2.20kg/10 sqm

TOTAL FINISHING WORK AMOUNT 36937429.84

XI 15.0 DISMANTLING AND DEMOLISHING WORK

Demolishing cement concrete manually/ by mechanical means including disposal of material

within 50 metres lead as per direction of Engineer - in - charge.

81.1 15.2.2 Nominal concrete 1:4:8 or leaner mix (including equivalent design mix) cum 34.31 1609.30 55215.19

Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars

82 15.3 and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- cum 120.07 3800.90 456374.41

Demolishing brick work manually/ by mechanical means including stacking of serviceable

83 15.7 material and disposal of unserviceable material within 50 metres lead as per direction of

Engineer-in-charge.

Dismantling manually/ by mechanical means including stacking of serviceable material and

84 15.43 disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-

Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by

mechanical means, including loading, transporting, unloading to approved municipal dumping

ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including

all lifts involved.

Disposal of materials by Mechanical Transport including loading, unloading and stacking of

Building Rubbish

TOTAL DISMANTLING AND DEMOLISHING WORK AMOUNT 756310.17

XII 21.0 ALUMINIUM WORK

Providing and fixing double action hydraulic floor spring of approved brand and manufacture

conforming to IS : 6315, having brand logo embossed on the body / plate with double spring

mechanism and door weight upto 125 kg, for doors, including cost of cutting floors,

embedding in floors as required and making good the same matching to the existing floor

finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide

plate etc. complete as per the direction of Engineerin- charge.

87.1 21.4.1 With stainless steel cover plate minimum 1.25 mm thickness each 2.00 3022.37 6044.73

Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand

and manufacture, including providing and fixing top & bottom pivot & double acting hydraulic

88 21.18 floor spring type fixing arrangement and making necessary holes etc. for fixing required door sqm 4.80 5700.31 27361.49

fittings, all complete as per direction of Engineer-in-charge (Door handle, lock and stopper

etc.to be paid separately).

Filling the gap in between aluminium/ stone/ wood frame and adjacent RCC/Brick/ Stone/

wood/ Ceramic/ Gypsum work by providing weather/ structural non sag elastomeric PU

sealant over backer rod of approved quality as per architectural drawings and direction of

Engineer-in-charge complete, complying to ASTM C920, DIN 18540-F & ISO 11600

89.1 21.19.1 Upto 5 mm depth and 5 mm width metre 4608.20 158.51 730452.37

TOTAL ALUMINIUM WORK AMOUNT 763858.60

XIII 22.0 WATER PROOFING WORK

Providing and laying water proofing treatment to vertical and horizontal surfaces of

depressed portions of W.C., kitchen and the like consisting of:

(i) Ist course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound

conforming to IS : 2645 in recommended proportions including rounding off junction of

vertical and horizontal surface.

(ii) IInd course of 20 mm cement plaster 1:3 (1 cement : 3 coarse sand) mixed with water

90 22.3 proofing compound in recommended proportion including rounding off junction of vertical and sqm 1348.96 823.70 1111142.24

horizontal surface.

(iii) IIIrd course of applying blown or residual bitumen applied hot at 1.7 kg. per sqm of area.

(iv) IVth course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be

100 mm wide and pasted to each other with bitumen @ 1.7 kg/sqm).

Providing and spray applying two component hybrid polyuria polyurethane waterproofing

91 22.27 system at all levels for podium garden waterproofing by the manufacturer or his approved

applicator consistin of following operations -

(a) Brushing and vacuum cleaning the surface to make free from any loose material, oil,

grease, burr, dirt, dust etc.

(b) Repairing the surface if required, as per recommendation of manufacturer or his approved

applicator to make it water tight for which nothing extra shall be paid.

(c) Providing and applying by spray or brush, two component solvent free resin/ epoxy primer

mixed in proportion of volume / weight as recommended by manufacturer over cement

concrete surface in dry condition, having consumptionvaries from 0.20 to 0.40 kg/sqm

depending on the porosity and undulations in the surface.

(d) Providing and sprinkling washed coarse sand, as recommended by manufacturer,

overfreshly laid primed tacky surface @ 0.25 to 0.40 kg/sqm as directed by Engineer-in-

(e) Over primed sandy surface, providing and spray applying two component hyrbrid polyurea

polyurathane coating system, which shall be solvent free, mixed in proportion by volume / by

weight as recommended by manufacturer having elongation > 400%, shore a hardness > 75

(after 28 days), tensile strength of minimum of 10MPa as per DIN / ASTM and tear strength

minimum 30 N/mm as per DIN 53515 or minimum 45 N/mm as per ASTM D624 and 20

maximum gel time / reaction time with minimum 1.5 mm dry film thickness of two coats.

(f) A layer of non woven polypropleyne geotextile of minimum mass / unit area of 120 gsm

with an overlap of 50 mm shall be laid over the polyurea/ polyurethane coatin surface, having

minimum tensile strength 2.40 KN/m as per ASTM D 4595.

(g) Providing and laying screed of cement concrete 1:1.5:3 ( 1 Cement : 1.5 Coarse Sand : 3

Graded stone aggregate 20 mm nominal size) of minimum thickness 50 mm at khurrah with

a slope of 1:100 towards khurra to ridge of roof (screed shall be paid for seperately).

(h) Providing and laying dimple drain boards with inbuilt geo textile drainage membrane on

top having dimple height of 20-25 mm, average number of dimples 400 per sqm,

compressive strength not less than 180 KN/sqm and geotextile member having mass of 120

gsm, laid with minimum overlap of 50 mm.

Note : If HDPE drain cells / Drainmats along with a layer of geotextile having weight of 120

gsm and tensile strength not less than 2.4 KN/m as per ASTM D 4595 is provided in place of

dimple drain board with inbuilt geotextile, it shall not be paid exttra.

22.27.1 New work on horizontal surfaces sqm 3557.60 2891.90 10288213.07

TOTAL WATER PROOFING WORK AMOUNT 11399355.31

XIV 25.0 STRUCTURAL GLAZING WORK

Providing and supplying aluminium extruded tubular and other aluminium sections as per the

architectural drawings and approved shop drawings , the aluminium quality as per grade

6063 T5 or T6 as per BS 1474,including super durable powder coating of 60-80 microns

92 25.1 conforming to AAMA 2604 of required colour and shade as approved by the Engineer-in- kg 6968.85 443.43 3090164.33

Charge. ( The item includes cost of material such as cleats, sleeves, screws etc. necessary

for fabrication of extruded aluminium frame work. Nothing extra shall be paid on this

account). The weight of aluminium extruded section shall be taken for purpose of payment.

Designing, fabricating, testing, protection, installing and fixing in position semi (grid) unitized

system of structural glazing (with open joints) for linear as well as curvilinear portions of the

building for all heights and all levels, including:

(a) Structural analysis & design and preparation of shop drawings for the specified design

loads conforming to IS 875 part III (the system must passed the proof test at 1.5 times

93 25.2 design wind pressure without any failure), including functional design of the aluminum

sections for fixing glazing panels of various thicknesses, aluminium cleats, sleeves and

splice plates etc. gaskets, screws, toggles, nuts, bolts, clamps etc., structural and weather

silicone sealants, flashings, fire stop (barrier)- cum-smoke seals, microwave cured EPDM

gaskets for water tightness, pressure equalisation & drainage and protection against fire

hazard including:

(b) Fabricating and supplying serrated M.S. hot dip galvanised / Aluminium alloy of 6005 T5

brackets of required sizes, sections and profiles etc. to accommodate 3 Dimentional

movement for achieving perfect verticality and fixing structural glazing system rigidly to the

RCC/ masonry/structural steel framework of building structure using stainless steel anchor

fasteners/ bolts, nylon seperator to prevent bimetallic contacts with nuts and washers etc. of

stainless steel grade 316, of the required capacity and in required numbers.

(c) Providing and filling, two part pump filled, structural silicone sealant and one part weather

silicone sealant compatible with the structural silicone sealant of required bite size in a clean

and controlled factory / work shop environment, including double sided spacer tape, setting

blocks and backer rod, all of approved grade, brand and manufacture, as per the approved

sealant design, within and all around the perimeter for holding glass.

(d) Providing and fixing in position flashings of solid aluminium sheet 1 mm thick and of

sizes, shapes and profiles, as required as per the site conditions, to seal the gap between the

building structure and all its interfaces with curtain glazing to make it watertight.

(e) Making provision for drainage of moisture/ water that enters the curtain glazing system to

make it watertight, by incorporating principles of pressure equalization, providing suitable

gutter profiles at bottom (if required), making necessary holes of required sizes and of

required numbers etc. complete. This item includes cost of all inputs of designing, labour for

fabricating and installation of aluminium grid, installation of glazed units, T&P, scaffolding

and other incidental charges including wastages etc., enabling temporary structures and

services, cranes or cradles etc. as described above and as specified.

The item includes the cost of getting all the structural and functional design including shop

drawings checked by a structural designer, dully approved by Engineer-in-charge. The item

also includes the cost of all mock ups at site, cost of all samples of the individual

components for testing in an approved laboratory, field tests on the assembled working

structural glazing as specified, cleaning and protection till the handing over of the building for

occupation. In the end, the Contractor shall provide a water tight structural glazing having all

the performance characteristics etc. all complete as required, as per the Architectural

drawings, as per item description, as specified, as per the approved shop drawings and as

directed by the Engineer- in-Charge.

Note:- 1. The cost of providing extruded aluminium frames, shadow boxes, extruded

aluminium section capping for fixing in the grooves of the curtain glazing and vermin proof

stainless steel wire mesh shall be paid for separately under relevant items under this sub-

head. However, for the purpose of payment, only the actual area of structural glazing

(including width of grooves) on the external face shall be measured in sqm. up to two decimal

places. Note:-2. The following performance test are to be conducted on structural glazing

system if area of structural glazing exceeds 2500 Sqm from the certified laboratories

accreditated by NABL(National Accreditation Board for Testing and Calibration Laboratories),

Department of Science & Technologies, India. Cost of testing is payable separately. The NIT

approving authority will decide the necessity of testing on the basis of cost of the work, cost

of the test and importance of the work. Performance Testing of Structural glazing system

Tests to be conducted in the NABL accredited lab or any other accreditation body which

operates in accordance with ISO/IEC 17011 and accredits labs as per ISO/IEC 17025 1.

Performance Laboratory Test for Air Leakage Test (-50pa to - 300pa) & (+50pa to +300pa)

as per ASTM E-283-04 testing method for a range of

testing limit 1 to 200 mVhr

2. Static Water Penetration Test. (50pa to 1500pa) as per ASTME- 331-09 testing method for

a range up to 2000 ml.

3. Dynamic Water Penetration (50pa to 1500pa) as per AAMA 501.01- 05 testing method for

a range upto 2000 ml

4. Structural Performance Deflection and deformation by static air pressure test (1.5 times

design wind pressure without any failure) as per ASTME-330-10 testing method for a range sqm 304.82 3757.29 1145296.57

5. Seismic Movement Test (upto 30 mm) as per AAMA 501.4-09 testing method for

Qualitative test, Tests to be conducted on site.

6. Onsite Test for Water Leakage for a pressure range 50 kpa to 240 kpa (35psi) upto 2000

Providing, assembling and supplying vision glass panels (IGUs) comprising of hermetically-

sealed 6-12- 6 mm insulated glass (double glazed) vision panel units of size and shape as

required and specified, comprising of an outer heat strengthened float glass 6 mm thick, of

approved colour and shade with reflective soft coating on surface # 2 of approved colour and

94 25.3 shade, an inner Heat strengthned clear float glass 6 mm thick, spacer tube 12 mm wide, sqm 1279.43 3980.12 5092290.83

dessicants, including primary seal and secondary seal (structural silicone sealant) etc. all

complete for the required performances, as per the Architectural drawings, as per the

approved shop drawings, as specified and as directed by the Engineerin- Charge. The IGUs

shall be assembled in the factory/ workshop of the glass processor.

Extra for openable side / top hung vision glass panels (IGUs) including providing and

supplying at site all accessories and hardwares for the openable panels as specified and of

the approved make such as heavy duty stainless steel friction hinges, min 4 -point cremone

95 25.4 locking sets with stainless steel plates, handles, buffers etc. including necessary stainless sqm 25.69 3929.61 100951.59

steel screws/ fasteners, nuts, bolts, washers etc. all complete as per the Architectural

drawings, as per the approved shop drawings, as specified and as directed by the Engineer-

Providing, fabricating and supplying shadow box of required size and shape, for fixing in the

spandrel portion of the structural glazing, in linear as well as curvilinear portions of the

building by providing semi -rigid, inorganic, non-combustible fibre glass wool insulation 50

mm thick, conforming to IS: 8183 and BS: 3958 Part 5. The insulation layer shall have facing

96 25.5 (factory bonded on surface # 1 of the fibre glass insulation layer), of black non-woven fibre sqm 47.97 2311.47 110881.38

glass tissue of nominal thickness 0.5 mm and nominal mass not less than 60 gm /sqm,

made of randomly oriented glass fibres distributed in a binder by a wet-lay process including

fixing 1.5 mm thick solid aluminum sheet backing using, 6 mm thick cement board including

SS rivets, nuts, bolts, washers etc complete.

Providing and supplying Spandrel Glass Panels comprising of 6 mm thick heat strengthened

monolithic float glass of approved colour and shade with reflective soft coating on surface # 2

of approved colour and shade so as to match the colour and shade of the IGUs in the vision

panels etc. ,all complete for the required performances as specified, as per the Architectural

drawings, as per the approved shop drawings, as specified, and as directed by the Engineer-

in- Charge. For payment, only the actual area of glass on face # 1 of the glass panels (but

excluding the area of grooves and weather silicone sealant) provided and fixed in position,

shall be measured in sqm. (Payment for fixing of Spandrel Glass Panels in the curtain

glazing is included in cost of relevent Item*).“(i) Coloured tinted float glass 6 mm thick

substrate with reflective soft coating on face # 2, having properties as visible Light

transmittance (VLT) of 25 to 35 %, Light reflection internal 10 to 15%, light reflection external

10 to 20 %, shading coefficient (0.25- 0.28) and U value of 3.0 to

3.3 W/m2 K etc. . The properties of performance glass shall be decided by technical

sanctioning authority as per the site requirement.

TOTAL STRUCTURAL GLAZING WORK AMOUNT 9665381.02

XV MISCELLANEOUS WORK

Supply & Fixing 5 Knuckle, 2 bearing butt hinges size 4" x 3" x 3mm, in SS 304 and in satin

98 MR-2 stainless steel. As per EN 1935, CE Marked. Suitable for door weights upto 120kgs. as per each 268.00 491.00 131588.00

direction of engineer-in-charge

Supply & Fixing rack and pinion door closer EN size 3-6, with standard arm and two

independent closing valves and latching speed adjustable by arm. All adjustment screws face

fixed with slide plate. For Door width upto 1400mm Silver finish. As per EN 1154 and CE

marked. as per direction of engineer-in-charge

Supply & Fixing Automatic door bottom RP8si seal from Raven,extruded silicon sealing

component, spring loaded to lift clear of the floor. Concealed mounted in a 15mm x 34mm

groove. Max gap 13mm. Finish: Anadoised satin clear. L=920mm as per direction of engineer-

Supply & Fixing Surface mounted door coordinator for double doors SR 390, zinc plated for

101 MR-5 steel doors, non-Handed as per EN 1158 and CE marked. as per direction of engineer-in- each 120.00 14163.00 1699560.00

Supply & Fixing Delta Seal for acoustic, fire and smoke protection, suitable for wooden and

102 MR-6 steel frames, self adhesive, Finish = Black, Length = 1 x 2000mm, Height- 2 x 2750mm as each 120.00 7180.00 861600.00

per direction of engineer-in-charge

Providing and fixing G.I Chicken mesh having wire of thickness 22 SWG and minimum

aperture of 20mm X20 MM of approved quality over the junction of RCC member and brick

103 MR-7 /AAC wall including fixing with U nails /Screw 150 mm centre to centre in both direction sqm 2524.40 145.00 366038.00

before plastering etc all complete as per the direction of Engineer in charge

TOTAL MISCELLANEOUS WORK AMOUNT 4981786

Name of Project : CONSTRUCTION OF INTEGRATED TOWNSHIP AT CHANDRAPURA, JHARKHAND

Name of Work : Plumbing Works

EXECUTIVE HOSTEL

S. No. Description PLUMBING

DSR NSR Total

1 Internal Plumbing Works. 64,20,081.41 16,58,967.00 80,79,048.41

Grand Total 80.79 Lakh

Grand Total 80.79 Lakh

Name of Project : CONSTRUCTION OF INTEGRATED TOWNSHIP AT CHANDRAPURA, JHARKHAND

Name of Work : Plumbing Works

EXECUTIVE HOSTEL

Ref. DSR- DSR/NS

S. No. Description of Item Unit Qty

2023/MR Rate DSR NSR

1.0 Internal Plumbing Works.

1 17.10 Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as

per IS 13983 with C.I. brackets and stainless steel plug 40 mm

including painting of fittings and brackets, cutting and making

good the walls wherever required :

a 17.10.1.3 Kitchen sink with drain board 510x1040 mm bowl depth 200 mm

2 17.31 Providing and fixing mirror of superior glass (of approved quality)

complete with 6 mm thick hard board ground fixed to wooden

cleats with C.P. brass screws and washers complete.

3 17.28 Providing and fixing P.V.C. Waste pipe for sink or wash basin

including P.V.C. waste fittings complete. 0.00

a 17.28.1 Semi rigid pipe 0.00

4 DSR-17.22A Providing and fixing CP Brass 32mm size Bottle Trap of approved

quality & make and as per the direction of Engineer-in-charge.

5 DSR-17.34 Providing and fixing toilet paper holder : 0.00

Name of Project : CONSTRUCTION OF INTEGRATED TOWNSHIP AT CHANDRAPURA, JHARKHAND

Name of Work : Plumbing Works

EXECUTIVE HOSTEL

Ref. DSR- DSR/NS

S. No. Description of Item Unit Qty

2023/MR Rate DSR NSR

17.20 Providing and fixing white vitreous china pedestal type water

closet (European type W.C. pan) with seat and lid, 10 litre low

level white P.V.C. flushing cistern, including flush pipe, with

manually controlled device (handle lever), conforming to IS :

7231, with all fittings and fixtures complete, including cutting and

making good the walls and

floors wherever required : 0.00

6 17.2.1 W.C. pan with ISI marked white solid plastic seat and lid Each 72.00 6973.59 502098.71 0.00

6a 17.1 Providing and fixing water closet squatting pan (Indian type W.C.

pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level

white P.V.C. flushing cistern, including flush pipe, with manually

controlled device (handle lever) conforming to IS : 7231, with all

fittings and fixtures complete, including cutting and making good

the walls and floors wherever required

17.1.1 White Vitreous china Orissa pattern W.C. pan of size 580x440

mm with integral type foot rests Each 0.00 7243.14822 0.00 0.00

7.00 ,18.49 Providing and fixing C.P. brass bib cock of approved quality

conforming to IS:8931 : 0.00

Name of Project : CONSTRUCTION OF INTEGRATED TOWNSHIP AT CHANDRAPURA, JHARKHAND

Name of Work : Plumbing Works

EXECUTIVE HOSTEL

Ref. DSR- DSR/NS

S. No. Description of Item Unit Qty

2023/MR Rate DSR NSR

8.00 ,18.53 Providing and fixing C.P. brass angle valve for basin mixer and

geyser points of approved quality conforming to IS:8931

Name of Project : CONSTRUCTION OF INTEGRATED TOWNSHIP AT CHANDRAPURA, JHARKHAND

Name of Work : Plumbing Works

EXECUTIVE HOSTEL

Ref. DSR- DSR/NS

S. No. Description of Item Unit Qty

2023/MR Rate DSR NSR

9.00 17.7 Providing and fixing wash basin with C.I. brackets, 15 mm C.P.

brass pillar taps, 32 mm C.P. brass waste of standard pattern,

including painting of fittings and brackets, cutting and making

good the walls wherever require: 0.00

17.7.1 White Vitreous China Wash basin size 630x450 mm with a pair of

15 mm C.P. brass pillar taps] Each 72.00 2835.06 204124.62 0.00

10.00 18.21 Providing and fixing uplasticised PVC connection pipe with brass

unions : Each 0.00

11.00 18.22 Providing and fixing C.P. brass shower rose with 15 or 20 mm

12.00 17.22B Providing and fixing CP Brass Single lever telephonic wall mixer of

quality & make as approved by Engineer in charge. 0.00

NS-12 Providing & Fixing CP Brass Shower Spout Each 72.00 2952.00 0.00 2,12,544.00

13.00 NS-2 Providing and fixing C.P. cast brass twin coat hooks fixed to PVC

rawl plug with SS screws. Each 72.00 1315.00 0.00 94,680.00

Name of Project : CONSTRUCTION OF INTEGRATED TOWNSHIP AT CHANDRAPURA, JHARKHAND

Name of Work : Plumbing Works

EXECUTIVE HOSTEL

Ref. DSR- DSR/NS

S. No. Description of Item Unit Qty

2023/MR Rate DSR NSR

14.00 NS-3 Providing and fixing of ABS health spary which can tolerate water

pressure up to 6 bar flow pressure with metal hose and holder in

Polished Chrome. Each 72.00 1613.00 1,16,136.00

15.00 NS-4 Providing, fixing, testing and commissioning of CP brass swan

neck wall mounted sink mixer with wall flange and swinging

casted spout complete as required and making good the walls

wherever required. [Make :Euronics, Model:FLO-3012A].Or

equivalent/ approved list of Make Each 72.00 4217.00 0.00 3,03,624.00

16.00 17.72 Providing and fixing PTMT towel ring trapezoidal shape 215 mm

long, 200 mm wide with minimum distances of 37 mm from wall

face with concealed fittings arrangement of approved quality and

colour,weighing not less than 88 gms. Each 72.00 248.26 17874.44 -

17.00 18.65 Providing and fixing PTMT soap Dish Holder having length of

138mm,breadth 102mm, height of 75mm with concealed fitting

arrangements,weighing not less than 106 gms.

Name of Project : CONSTRUCTION OF INTEGRATED TOWNSHIP AT CHANDRAPURA, JHARKHAND

Name of Work : Plumbing Works

EXECUTIVE HOSTEL

Ref. DSR- DSR/NS

S. No. Description of Item Unit Qty

2023/MR Rate DSR NSR

19.00 17.5 Providing and fixing white vitreous china flat back half stall urinal

of size 580x380x350 mm with white PVC automatic flushing

cistern, with fittings, standard size C.P. brass flush pipe, spreaders

with unions and clamps (all in C.P. brass) with waste fitting as per

IS : 2556, C.I. trap with outlet grating and other couplings in C.P.

brass, including painting of fittings and cutting and making good

the walls and floors wherever required :

17.5.1 Single half stall urinal with 5 litre P.V.C. automatic flushing cistern

20.00 17.73 Providing and fixing PTMT towel rail complete with brackets fixed

to wooden cleats with CP brass screws with concealed fittings

arrangement of approved quality and colour.

21.00 NS-5 Supply, installation, testing and commissioning of horizontal type

storage hot water heater within-built pressure relief valve, rated

for inlet water pressure upto 6 bar complet in all respects

including inlet, oulet connections, fixing bolts etc. and testing

complete. 0.00

Name of Project : CONSTRUCTION OF INTEGRATED TOWNSHIP AT CHANDRAPURA, JHARKHAND

Name of Work : Plumbing Works

EXECUTIVE HOSTEL

Ref. DSR- DSR/NS

S. No. Description of Item Unit Qty

2023/MR Rate DSR NSR

B Soil, Waste, Vent & Rain Water Pipes 0

21.00 Making khurras 45x45 cm with average minimum thickness of 5

cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded

stone aggregate of 20 mm nominal size) over P.V.C. sheet

1mx1mx400micron, finished with 12mm cement plaster 1:3 (1

cement : 3 coarse sand) and a coat of neat cement, rounding the

edges and making and finishing the outlet complete.

22.00 Providing and fixing to the inlet mouth of rain water pipe cast

iron grating 15 cm diameter and weighing not less than 440

23.00 Providing and fixing soil, waste, vent and rain water pipes 0.00

Hubless centrifugally cast iron pipes epoxy coated inside &

24.00 Providing and fixing MS holder bat clamps of approved design to

cast iron (spun) pipe embedded in and Including cement concrete

blocks 10 x10 x10cm of 1:2:4 mix (1 cement : 2 coarse sand : 4

graded stone aggregate 20mm nominal size) including cost of

cutting holes and making good the walls etc.

Name of Project : CONSTRUCTION OF INTEGRATED TOWNSHIP AT CHANDRAPURA, JHARKHAND

Name of Work : Plumbing Works

EXECUTIVE HOSTEL

Ref. DSR- DSR/NS

S. No. Description of Item Unit Qty

2023/MR Rate DSR NSR

25.00 Providing and fixing bend of required degree with access door,

insertion rubber washer 3mm thick, bolts and nuts complete.

Hubless centrifugally cast iron epoxy coated inside & outside IS :

26.00 Providing and fixing plain bend of required degree. 0.00

Hubless centrifugally cast iron epoxy coated inside & outside IS :

27.00 Providing and fixing double equal plain junction of required

Hubless centrifugally cast iron pipes epoxy coated inside &

28.00 Providing and fixing single equal plain junction of required degree

Hubless centrifugally cast iron epoxy coated inside & outside IS :

Name of Project : CONSTRUCTION OF INTEGRATED TOWNSHIP AT CHANDRAPURA, JHARKHAND

Name of Work : Plumbing Works

EXECUTIVE HOSTEL

Ref. DSR- DSR/NS

S. No. Description of Item Unit Qty

2023/MR Rate DSR NSR

29.00 Providing and fixing single unequal plain junction of required

Hubless centrifugally cast iron epoxy coated inside & outside IS :

30.00 Providing and fixing Hubless cast iron offsets epoxy coated inside

& outside as per IS : 15905 0.00

17.54.A 130 mm offsets 0.00

31.00 Providing and fixing terminal guard: 0.00

Hubless centrifugally cast iron epoxy coated inside & outside IS :

32.00 Providing and fixing shielded coupling for Hubless centrifugally

cast iron pipe 0.00

17.57A.1 SS 304 grade coupling with EPDM rubber gasket Each 240.00 462.423115 1,10,981.55

33.00 Painting with synthetic enamel paint of approved drand and

manufacture to give an even shade 0.00

13.61 Two more coast on new work sqm 180.00 166.86 30034.76

Name of Project : CONSTRUCTION OF INTEGRATED TOWNSHIP AT CHANDRAPURA, JHARKHAND

Name of Work : Plumbing Works

EXECUTIVE HOSTEL

Ref. DSR- DSR/NS

S. No. Description of Item Unit Qty

2023/MR Rate DSR NSR

P/F M.S. cap 100 mm dia Each 12.00 240.82 2889.81

34.00 Providing and laying in position cement concrete of specified

grade excluding the cost of centering and shuttering - All work up

to plinth level: 0.00

4.1 1:2:4 (1 cement :2 coarse sand: 4 hard stone aggregate 20mm

35.00 Providing and fixing trap of self cleansing design with screwed

down or hinged with or without vent arm complete, including

cost of cutting and making good the walls and floors.

a ,17.60 100 mm inlet and 100 mm outlet 0.00

17.60.1 Hubless centrifugally cast (spun) iron epoxy coated inside &

b 100 mm inlet and 75 mm outlet 0.00

17.60.2 Hubless centrifugally cast (spun) iron epoxy coated inside &

outside as per IS:15905 Each 72.00 632.98 45574.23 0.00

36.00 Providing and fixing SS grating of approved quality and colour.

NS-6 Circular type 125 mm nominal dia [Make :Euronics, Model:

EFG01P-55].Or equivalent/ approved list of Make Each 216.00 635.00 0.00 1,37,160.00

Name of Project : CONSTRUCTION OF INTEGRATED TOWNSHIP AT CHANDRAPURA, JHARKHAND

Name of Work : Plumbing Works

EXECUTIVE HOSTEL

Ref. DSR- DSR/NS

S. No. Description of Item Unit Qty

2023/MR Rate DSR NSR

37.00 Providing, laying, testing & commissioning of 'B' class heavy duty

G.I. pipe conforming to IS 1239 including welding, fittings like

elbows, tees, flanges, tapers, nuts, bolts, gaskets etc. and fixing

the pipe on the wall/ceiling with suitable clamp/support frame

and painting with two or more coats of synthetic enamel paint of

required shade complete as required :

Fire DSR 27.8 For WB, Urinal FT & FD and Sink Drain pipe

40 mm dia nominal bore Metre 288.00 1033.91 297766.02 0.00

38.00 Providing & fixing on wall face unplasticised -Rigid PVC rain water

pipes conforming to IS:13592 Tyape A included jointing with seal

ring conforning to IS:5382 leaving 10 mm gap for thermal

expansion. (i)Single socketed pipes. 0.00

39.00 Providing, fixing on wall face unplasticised - PVC moulded fittings

/accessories for unplasticised - Rigid PVC rain water pipes

conforming to IS ; 13592 Type A including jointing with seal ring

conforming to IS ; 5382 leaving 10 mm gap for thermal

expansion. 0.00

12.42 Coupler -110 mm diameter Each 0.00 145.72 0.00 0.00

Name of Project : CONSTRUCTION OF INTEGRATED TOWNSHIP AT CHANDRAPURA, JHARKHAND

Name of Work : Plumbing Works

EXECUTIVE HOSTEL

Ref. DSR- DSR/NS

S. No. Description of Item Unit Qty

2023/MR Rate DSR NSR

39.00 NS 7 Providing and fixing of 110x75 mm dia uPVC Balcony Drain

Name of Project : CONSTRUCTION OF INTEGRATED TOWNSHIP AT CHANDRAPURA, JHARKHAND

Name of Work : Plumbing Works

EXECUTIVE HOSTEL

Ref. DSR- DSR/NS

S. No. Description of Item Unit Qty

2023/MR Rate DSR NSR

C Internal Water Supply

41.00 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,

having thermal stability for hot & cold water supply including all

CPVC plain & brass threaded fittings i/c fixing the pipe with

clamps at 1.00 m spacing. This includes jointing of pipes & fittings

with one step CPVC solvent cement and testing of joints

complete as per direction of Engineer in Charge.

18.70 Internal Work - Exposed on Wall

a 25 mm nominal outer dia .Pipes. Metre 240.00 429.78 103146.95 0.00

a 18.7.3 32 mm nominal outer dia .Pipes. Metre 90.00 555.22 49969.63 0.00

b 18.7.4 40 mm nominal outer dia .Pipes. Metre 60.00 752.37 45142.04 0.00

18.7.5 50 mm nominal outer dia .Pipes. Metre 30.00 999.82 29994.62 0.00

42.00 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,

having thermal stability for hot & cold water supply including all

CPVC plain & brass threaded fittings i/c fixing the pipe with

clamps at 1.00 m spacing. This includes jointing of pipes & fittings

with one step CPVC solvent cement and the cost of cutting chases

and making good the same including testing of joints complete as

per direction of Engineer in Charge.

,18.8 Concealed work including cutting chases and making good the

walls etc. 0.00

Name of Project : CONSTRUCTION OF INTEGRATED TOWNSHIP AT CHANDRAPURA, JHARKHAND

Name of Work : Plumbing Works

EXECUTIVE HOSTEL

Ref. DSR- DSR/NS

S. No. Description of Item Unit Qty

2023/MR Rate DSR NSR

a 20 mm nominal outer dia .Pipes. Metre 660.00 575.39 379759.56 0.00

b 18.8.2 25 mm nominal outer dia .Pipes. Metre 330.00 671.35 221544.07 0.00

43.00 Providing and fixing G.I. pipes with two coats of anti-corrosive

bitumastic paint of approved quality : complete with G.I. fittings

and clamps, i/c cutting and making good the walls etc.

,18.10 Internal work - Exposed on Wall 0

a 15 mm dia nominal bore Metre 30.00 405.06 12151.65

b 18.12.2 & 20 mm dia nominal bore

44.00 18.10.2 & Providing, laying, testing & commissioning of 'B' class heavy duty

18.40.2 G.I. pipe conforming to IS 1239 including welding, fittings like

elbows, tees, flanges, tapers, nuts, bolts, gaskets etc. and fixing

the pipe on the wall/ceiling with suitable clamp/support frame

and painting with two or more coats of synthetic enamel paint of

required shade complete as required :

c Fire DSR - 27.8 25 mm dia nominal bore Metre 5.00 760.98 3804.92 0.00

d DSR Fire-27.8.1 32 mm dia nominal bore

e DSR Fire-27.8.2 40 mm dia nominal bore

f DSR Fire-27.8.3 50 mm dia nominal bore

Name of Project : CONSTRUCTION OF INTEGRATED TOWNSHIP AT CHANDRAPURA, JHARKHAND

Name of Work : Plumbing Works

EXECUTIVE HOSTEL

Ref. DSR- DSR/NS

S. No. Description of Item Unit Qty

2023/MR Rate DSR NSR

g DSR Fire-27.8.4 65 mm dia nominal bore

h DSR Fire-27.8.5 80 mm dia nominal bore

DSR Fire-27.8.6 100 mm dia nominal bore

DSR Fire-27.8.7

Name of Project : CONSTRUCTION OF INTEGRATED TOWNSHIP AT CHANDRAPURA, JHARKHAND

Name of Work : Plumbing Works

EXECUTIVE HOSTEL

Ref. DSR- DSR/NS

S. No. Description of Item Unit Qty

2023/MR Rate DSR NSR

45.00 Constructing masonry Chamber 30x30x50 cm inside, in brick work

in cement mortar 1:4 (1 cement :4 coarse sand) for stop cock,

with C. I. surface box 100x100 x75 mm (inside) with hinged cover

fixed in cement concrete slab 1:2:4 mix (1 cement : 2 coarse sand

: 4 graded stone aggregate 20 mm nominal size), i/c necessary

excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand :

10 graded stone aggregate 40 mm nominal size ) and inside

plastering with cement mortar 1:3 (1 cement : 3 coarse sand)

12mm thick, finished with a floating coat of neat cement

complete as per standard design :

a DSR-18.32 With common burnt clay F.P.S.(non modular) bricks of class

designation 7.5 Each 0.00 2132.68 0.00 0.00

46.00 Providing and placing on terrace (at all floor levels) polyethylene

water storage tank, IS : 12701 marked, with cover and suitable

locking arrangement and making necessary holes for inlet, outlet

and overflow pipes but without fittings and the base support for

Name of Project : CONSTRUCTION OF INTEGRATED TOWNSHIP AT CHANDRAPURA, JHARKHAND

Name of Work : Plumbing Works

EXECUTIVE HOSTEL

Ref. DSR- DSR/NS

S. No. Description of Item Unit Qty

2023/MR Rate DSR NSR

47.00 Making core cutting machine up to 15x15 cm in R.C.C. floors and

roofs for passing drain pipe etc. and repairing the hole after

insertion of drain pipe etc. with cement concrete 1:2:4 (1 cement

: 2 coarse sand : 4 graded stone aggregate 20 mm nominal size),

including finishing complete so as to make it leak proof.

48.00 Providing and fixing gun metal gate valve with C.I. wheel of

approved quality (screwed end) : 0

49.00 Supplying, fixing, testing and commissioning of butterfly

valve of PN 1.6 rating with bronze/gunmetal seat duly ISI

marked complete with nuts, bolts, washers, gaskets

conforming to IS 13095 of following sizes as required : 0.00

50.00 Providing and fixing gun metal non- return valve of approved

quality (screwed end) : 0.00

Name of Project : CONSTRUCTION OF INTEGRATED TOWNSHIP AT CHANDRAPURA, JHARKHAND

Name of Work : Plumbing Works

EXECUTIVE HOSTEL

Ref. DSR- DSR/NS

S. No. Description of Item Unit Qty

2023/MR Rate DSR NSR

51.00 Providing and fixing forged brass ball valve of brass body with

hard chrome plated steel ball inside PTFE (Teflon) seat & ring with

chrome plated centre handle with female BSP threads complete

in all respects.

a NS-8 15 mm nominal bore Each 60.00 368.00 0.00 22080.00

b NS-9 20 mm nominal bore Each 108.00 513.00 0.00 55404.00

52.00 NS 10 Providing and fixing forged brass single acting air release valve

with screwed inlet 25 mm dia. Each 12.00 656.00 0.00 7872.00

53.00 Providing and fixing ball valve (brass) of approved quality, High or

18.18 low pressure, with plastic floats complete :.

Name of Project : CONSTRUCTION OF INTEGRATED TOWNSHIP AT CHANDRAPURA, JHARKHAND

Name of Work : Plumbing Works

EXECUTIVE HOSTEL

Ref. DSR- DSR/NS

S. No. Description of Item Unit Qty

2023/MR Rate DSR NSR

Solar Water Heaters

54.00 Supply, erection, testing & commissioning of solar water

NS-11 heating system with following details :

System temperature output : 60 degree C (during clear sunny

System type : Thermo syphon

System : Non Pressurised

Application : Bathing / Washing / Cooking

Type of Solar Collectors : Copper tube Flat Plate Collectors as per

BIS with following specifications -

Size of Collector : 2080 x 1070 x 100 mm

Number of Collector : To suit system requirement.

Absorber area : 2 sq M

Weight : 46 Kg (Dry)

Absorber Coating : Selective - NALSUN

Absorbivity : > 0.95

Emissivity : < 0.2

Frame Material : 16 SWG extruded Aluminium

Glazing : Toughened Glass

Glass beeding : EPDM

Finish : Painted by approved shade

Hot water return pump

Name of Project : CONSTRUCTION OF INTEGRATED TOWNSHIP AT CHANDRAPURA, JHARKHAND

Name of Work : Plumbing Works

EXECUTIVE HOSTEL

Ref. DSR- DSR/NS

S. No. Description of Item Unit Qty

2023/MR Rate DSR NSR

Hardware : SS 304

Insulation : PUF

Collector Stand : 35x35x3 mm MS angle

Hot Water Tank : Cylindrical - vertical / horizontal, Stainless steel

304 grade with 100 mm thick Rock Wool insulation including 22

SWG aluminium cladding.

The entire system should be complete with internal piping in

SS(304) with 50 mm rock wool insulation of density 48 kg/m3

with 26 SWG Al cladding, necessary isolation valves, Y type CI

strainer, hardwares, temperature gauge of range 0 - 120oC, water

meter, MS angle iron structure of min thickness 3 mm duly

painted etc as required to complete the system in all respects.

The entire system should be approved by BIS as per IS : 12933

and as per local regulations.

System Capacity : 1500 liters ( storage tank of 2,000 litres ) per

day (LPD) having 15 collectors. Item 1.00 702339.00 - 702339.00

Total C/F to Summary 64,20,081.41 16,58,967.00

Summary of Cost

Project - Proposed Construction of Integrated Township at Chandrapura, Jharkhand.

Name of Block - Executive Residence Block

DSR-2025 Market Based

S.No. Description Total Amount

S.No. Description Total Amount

1 Cost of Internal Electrification & UPS Work 2,13,30,237.80 39,56,822.26 2,52,87,060.06

2 Cost of Fire Detection & Alarm Work 2,79,250.00 - 2,79,250.00

3 Cost of CCTV Surveillance Work 2,01,600.00 - 2,01,600.00

Detailed Estimate Based On DSR-2025 With Cost Index & Market Rate

Project - Proposed Construction of Integrated Township at Chandrapura, Jharkhand.

Name Of Work -Executive Residence Internal Electrification Work

Rate as per D.S.R. 2025 MARKET BASED

Sr.N Rate as per

Particulars Sch.No. Qty Unit Amount Rate Amount

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5

sq.mm FRLS PVC insulated copper conductor

single core cable in surface / recessed medium class PVC

1 conduit, with modular switch, modular plate, suitable GI box 1.10.1 1,880.00 Nos. 1,189.00 22,35,320.00 -

and earthing the point with 1.5 sq.mm FRLS PVC insulated

copper conductor single core cable etc. as required.

Wiring for twin control light point with 1.5 sq.mm FRLS PVC

insulated copper conductor single core cable in surface /

recessed medium class PVC conduit, 2 way modular switch,

modular plate, suitable GI box and earthing the point with 1.5

sq.mm FRLS PVC insulated copper conductor single core cable

etc. as required.

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC

insulated copper conductor single core cable in surface/

3 recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC 1.12 20,440.00 Meter 373 76,24,120.00 -

insulated copper conductor single core cable for loop earthing as required.

Wiring for circuit/ submain wiring alongwith earth wire with the

following sizes of FRLS PVC insulated copper conductor, single core cable

in surface/ recessed steel conduit as required.

Wiring for circuit/ submain wiring alongwith earth wire with the

following sizes of FRLS PVC insulated copper conductor, single core cable

in surface/ recessed medium class PVC conduit as required.

Supplying and drawing following pair 0.5 mm dia FRLS PVC

insulated annealed copper conductor, unarmored telephone

cable in the existing surface/ recessed steel/ PVC conduit as

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper

conductor PE insulated, shielded with fine tinned copper braid and

protected with PVC sheath in the existing surface/ recessed steel/ PVC

conduit as required.

Supplying and fixing of following sizes of medium class PVC

conduit along with accessories in surface/recess including

cutting the wall and making good the same in case of recessed

conduit as required.

Supplying and fixing following modular switch/ socket on the

9 existing modular plate & switch box including connections but 1.24 - -

excluding modular plate etc. as required.

a Telephone socket outlet 1.24.6 158.00 Each 168 26,544.00 -

b TV socket outlet 1.24.7 72.00 Each 168 12,096.00 -

c RJ45 socket cat 6 with shutter RA-1 14.00 Each - 487.56 6,825.90

Supplying and fixing two module stepped type electronic fan

10 regulator on the existing modular plate switch box including 1.25 272.00 Each 402 1,09,344.00 -

connections but excluding modular plate etc. as required.

Supplying and fixing following size/ modules, GI box alongwith

11 modular base & cover plate for modular switches in recess etc. 1.27 - -

Supplying and fixing suitable size GI box with modular plate and cover in

front on surface or in recess, including providing and fixing 3 pin 5/6 A

modular socket outlet and 5/6 A modular switch, connections etc. as

Supplying and fixing suitable size GI box with modular plate and cover in

front on surface or in recess, including providing and fixing 6 pin 5/6 &

15/16 A modular socket outlet and 15/16 A modular switch, connections

etc. as required.

Installation ,Testing, Commissioning of wall bracket /ceiling

fittings of all sizes and shapes containing upto two GLS/CFL/LED lamps

per fitting, complete with all accessories including connections etc. as

Supplying and fixing call bell/ buzzer suitable for single phase,

230 V, complete as required.

Installation of exhaust fan in the existing opening, including making good

the damage, connection, testing, commissioning etc. as required.

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing

surface/ recessed Steel/ PVC conduit as required.

a 1 run of cable MR 672.00 Meter - 67.26 45,198.72

Supplying and fixing suitable size GI box with modular plate and cover in

front on surface or in recess, including providng and fixing 2 nos. 3 pin 5/6

20 A modular socket outlet and 2 nos. 5/6 A modular switch, connections etc. 1.56 86.00 Each 757 65,102.00 -

as required. (For light plugs to be used in non residential buildings).

Supplying & fixing suitable size GI box wih modular plate and

cover in front on surface or in recess including providing and

fixing 25 A modular socket outlet and 25 A modular SP MCB, "C" curve

including connections, painting etc. as required.

Supplying and fixing following way, single pole and

neutral, sheet steel, MCB distribution board, 240 V,

on surface/ recess, complete with tinned copper bus

bar, neutral bus bar, earth bar, din bar,

interconnections, powder painted including earthing

etc. as required. (But without MCB/RCCB/Isolator)

Supplying and fixing following way, horizontal type three pole

and neutral, sheet steel, MCB distribution board, 415 V, on

surface/ recess, complete with tinned copper bus bar, neutral

bus bar, earth bar, din bar, interconnections, powder painted

including earthing etc. as required. (But without

MCB/RCCB/Isolator)

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve,

miniature circuit breaker suitable for inductive load of following poles in

the existing MCB DB complete with

connections, testing and commissioning etc. as required.

c Three Phase & Neutral 2.10.5 4.00 Each 1301 5,204.00 -

Supplying and fixing 40/63A rating, 415 V, 10 kA, "C" curve, miniature

circuit breaker suitable for inductive load of Four poles in the existing MCB

26 DB complete with connections, testing and commissioning etc. as required. RA-4 4.00 Each - 2,604.69 10,418.74

Similar to Legrand DX3 AC MCBs or equivalent.

Supplying and installing following size of perforated painted

with powder coating M.S. cable trays with perforation not more than

27 17.5%, in convenient sections, joined with connectors, suspended from the 4.1 - -

ceiling with M.S. suspenders including bolts & nuts, painting suspenders

etc as required.

a 100 mm width X 50 mm depth X 1.6 mm thickness 4.1.1 120.00 Each 623 74,760.00 -

b 300 mm width X 50 mm depth X 1.6 mm thickness 4.1.4 50.00 Each 866 43,300.00 -

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick

including accessories, and providing masonry enclosure with

cover plate having locking arrangement and watering pipe of

2.7 metre long etc. with charcoal/ coke and salt as required.

Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre

below ground as strip earth electrode, including connection/

30 terminating with G.I. nut, bolt, spring, washer etc. as required. 5.9 80.00 Meter 160.00 12,800.00 -

(Jointing shall be done by overlapping and with 2 sets of G.I. nut

bolt & spring washer spaced at 50mm)

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in

recess for connections etc. as required.

Providing and fixing 6 SWG dia G.I. wire on surface or in recess

35 for loop earthing along with existing surface/ recessed conduit/ 5.18 480.00 Meter 50 24,000.00 -

submain wiring/ cable as required.

SITC of 12W Extruded aluminium batten available in 2ft run length with

multiple lumen packages and suitable for surface, wall & conduit ounting

(with accessories). similar to Philips Type HSN Code MRP (INR) BN 021

LED12S 6500 PSU GR or equivalent.

Supply and fixing of water tight oblong 10 Watt LED bulkhead luminaire having

pressure diecast housing with driver set confirming to IP 65 and above Protection,

IK08, High purity / transmisivity UV stablized Non yellowish diffuser/ Reflector

for uniform light distribution, ditachable driver set, suitable for 24hrs continuous

38 operation complete in all respect. MR 39.00 Each - 2,367.08 92,316.12

1200 system lumen, >120lm/W, PF>0.95, CRI>70, >300V, over voltage

protection, 4KV internal surge protection with 5 year warrenty. CAT-AAA

LED Batten light (System lumen efficacy >135 lm/Watt)

Supplying, installation, Testing & Commissioning of LED surface mounted

Batten light of following body material and construction as per IS : 10322 with

driver (Replaceable) as per the requirement with Driver efficiency >85%

,Operating voltage AC 140-270 Volt, freq 50/60 hz, Operating temp range -

15 deg to 40 deg centigrade, internal surge protection of 2.5 KV with Short &

Open circuit protection ,THD < 10% , P. F.≥0.95, IP20, CRI >80 , Flicker

free (flicker should be below 5 %), life time (LED,Driver & electrical circuitry),

of minimum 50000 Burning Hours with , 70% of initial Lumen

maintained till life ends, CCT 3000°K / 4000°K / 5700°K /6000°K/

6500°K (As per ANSI Bin), SDCM (Standard Deviation Color Matching)

<3, Maximum power consumption should not more than the specified rating

and Fixture shall be of relevant BIS standard and trade mark certificate (

T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen

printing on housing. OEM must have its own in house NABL lab setup for

all testing facilities for LED fixtures. complete in all respect i/c

connections with 1.5 sq mm FRLS, PVC insulated copper conductor

single core cable and earthing etc. as required with Minimum 5 year OEM

warranty. System lumen efficacy >135 lm/Watt output . LM79 & LM80 Test

report from NABL lab for all testing required for LED fixtures as per BIS

shall be submitted. Shape size and CCT shall be as approved by Engineerin-

Charge as per requirement. (Thermal management: heat sink of

aluminum housing such that LED junction temperature shall not rise above

Powder coated die cast /Extruded aluminum Body (Thickness ≥ 1.20

41 Supply of 9W LED Bulb similar to philips or equivalent. RA-19 360.00 Each - 135.47 48,768.62

Supply of 250mm exhuast fan having Built with a durable powder-coated

metal body, this 150 mm exhaust fan brings both style and resilience to

kitchens, bathrooms, or compact spaces.

Equipped with a fast-spinning 1200 RPM motor, it swiftly eliminates

steam, smoke, and odors for a fresher indoor atmosphere.

The compact 250 mm sweep ensures a perfect wall or window installation

without sacrificing airflow.

Precision balanced metal blades deliver steady, powerful airflow while

keeping vibrations and noise minimal.

42 Designed to be energy-efficient, it uses approximately 48 W, offering strong RA-20 158.00 Each - 1,763.37 2,78,611.80

performance without raising your electricity bill.

Operates quietly around 40–45 dB, making it ideal for use near bedrooms,

studies, or any quiet area.

Comes with a sturdy steel bird guard to prevent insects and debris from

entering, protecting hygiene and motor health.

Featuring a corrosion-resistant finish, it stays looking fresh and functioning

well even in humid conditions.

Maintenance is hassle-free—blades and grill detach easily for quick

cleaning to ensure consistent airflow.

Brush Less Direct Current (BLDC) Fan without Remote

Supply, Installation, Testing and Commissioning of ceiling fan with Brush

Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. metal(

Aluminium alloy) blades, 30 cm long down rod, 2 nos. canopies, shackle

kit, safety rope, copper winding, steel/Al body

Power Factor not less than 0.9, Service Value (CM/M/W) minimum as

below, 350 RPM (tolerance as, per IS : 374-2019), THD (Total Harmonic

Distortion) less than 10%, suitable for operation with regulator for speed

control and all remaining accessories including safety pin, nut bolts,

washers, temperature rise=75 0C (max.), insulation resistance more than 2

mega ohm, suitable for 230 V, 50 Hz, single phase AC supply, Ceiling Fan

compliant to IS 374:2019 fan i/c external connections with 1.5 sq.mm

FRLS/HFFR, PVC insulated copper conductor single core cable and

earthing etc. as required.

1200mm, service value ≥ 6.0 CM/Min/Watt, air delivery 210 CM/Min

Supply and fixing hexagonal Round G.P.fan box approved make made up

of 1.0 mm thick ISI Marked G.P.sheet spot welded Four to Eight holes for

pipe entry of the box. Holes should be semi-shuttered type with 0.5 mm

46 G.P. Sheet made upper & lower cover duly screwed. Fixing with wiring 272.00 Each 220.65 60,016.80 -

conduit laid in the R.C.C. roof before concreting alongwith supply of all 2023 10.18

material, labour, T&P etc. required for proper completion of the work.

Supply Installation Testing and Commissioning of 400mm sweep

47 1500RPM energy efficient BLDC fan with double ball bearing for longer RA-2 14.00 Each - 6,359.54 89,033.53

life similar to CGE RENESA or equivalent.

Lightning Arrestor Work - -

Lightning Arrestor: Supply, installation, testing and commissioning of

External Lightning wide area protection system based on Eaarly Streamer

Emission (ESE) technology. Device shall emit electromagnetic impulse in

the form of a streamer into the air microseconds earlier than naturally

48 formed streamers. Device confirmg to NFC 17-102 and UNE 21186 MR 2.00 Each - 62,304.00 1,24,608.00

Standards. Appropriate non penetrating mounting arrangement. The device

shall be mounted at suitable clear to the highest point on the roof top.

(Model selected shall give coverage of 79 M radius @ min 5M height from

Down conductor:Supply, installation, testing and commissioning of 70

49 Sqmm twisted 19-Strand, bare Cu cable on surface/wall / as per site MR 470.00 Metre - 2,510.92 11,80,133.34

requirement and complete in all respect.

Lightning Counter :Supply and installation of counting the number of

lightning strikes without any power supply.

52 Test Link :Supply and installation of test link in weather proof IP 65 BOX. MR 2.00 Each - 2,832.00 5,664.00

Supply, installation, testing and commisioning of 2 x 25W LED Aviation

abstruction light medium bay type 62, complete with lamp, lamp holder,

Condenser necessary connecting wire, 1 X 25 AV with all necessary

hardware, accessories as required for complete installation. Rate shall

include the cost of necessary steel structures , fixing arrangements in this

item. Refer drawing.

SITC of LT switchgear panels suitable for 433 V, 3 phase, 4 wire, 50 Hz

power distribution system. The panel shall be Indoor, free standing, floor

mounting, sheet metal clad, cubicle, dead front, dust and vermin proof type

compartmentalised design fabricated out of 14 SWG CRCA sheet steel,

complete with colour coded, heat shrinkable PVC insulated, aluminium bus

bars and separate earth bus bar of adequate cross section through out the

length of the panel. The incoming and outgoing feeders shall be

accommodated in a fully segregated, modular multitier arrangement with - - -

adequate size and distinct cable alley, bus bar alley/chamber. The panel

shall be complete with name plate, earthing, numbering, danger plate etc. as

per specifications and drawings as required. The panel shall withstand the

fault level of 50kA as per Single Line Diagram. The Panel shall also be

capable to communicate status like ON/OFF/ Trip through

Modbus/Ethernet for major component like ACB, MCCB, MCB &

Multifunation meters.

The Main LT Panel shall use all draw out type breakers suitable for 415 V

AC, 3 phase, 50 Hz, 3 phase 4 wire supply system. Panel shall have

Buscoupler switching, auto operation of incommer and bus coupler, auto

start of D.G. Sets, auto D.G. running by pre set timing, auto changeover etc

and having following incomming and outgoing Air Circuit - - -

Breakers,microprocessor release for overload, short circuit, instantaneous &

earthfault protection with Current & Voltage metering & LCD display.

Air Circuit Breaker with microprocessor release ge metering & LCD display

, with ready to clsoe indicator, should have capability to communicate ON

/OFF/ Trip Status on Modbus/Ethernet and as per the detail specification of

ACB (Icu=Ics=Icw=65 KA (1 sec). MCCB, with microprocessor release

with LSIG protection functionand should not derate upto 50 decree

Centrigrate as per testing guideline as per IEC 60947-2 and all the ACB - - -

upto 2500Amp ACB should have same frame size LCD display for fault

trip history, haivng current limiting feature, double break mechanism &

capability to communicate ON /OFF/ Trip Status on Modbus/Ethernet. (65

55 EXECUTIVE RESIDENCE BLOCK L.T PANEL MR 1.00 Set 9,26,772.00 9,26,772.00

1 Nos. 800 Amp FP ACB 65KA LSIG having S/C, E/F O/C protection,

LCD Display having specs as per attached annexture

R,Y,B Phase indication Lamp with control MCB

On, Off, Trip Status Indication with control MCB

Inbuilt Zone Slelective Interlocking function

Multifunction Meter

1 Nos. 250 Amp FP MCCB 50 KA LSIG having S/C, E/F O/C protection,

LCD Display having specs as per attached annexture

R,Y,B Phase indication Lamp with control MCB

On, Off, Trip Status Indication with control MCB

Inbuilt Zone Slelective Interlocking function

Multifunction Meter

1 Nos. 250 Amp FP ATS

1 Nos. 1000 Amp FP busbars of aluminium alloy as per SLD. - -

1 Nos. 300 Amp FP busbars of aluminium alloy as per SLD. - -

12 Nos. 63 Amp FP MCCB 25 KA

On, Off, Trip Status Indication with control MCB

Multifunction Meter

LIFT + + Fire Fighting+ Plumbing +Spare

6 Nos. 63 Amp FP MCB 10 KA

On, Off, Trip Status Indication with control MCB - -

Common Area DB +Spare

6 Nos. 32 Amp FP MCB 10 KA

On, Off, Trip Status Indication with control MCB - -

Common Area DB +Spare

3 Nos. 250 Amp FP MCCB 25 KA

On, Off, Trip Status Indication with control MCB

Multifunction Meter

Meter Panel +Spare

Short Circuit Breaking capacity should not less than 10 KA. - -

RELAYS AS PER SLD - -

56 Floor Meter Panel MR 2.00 Set 4,01,554.00 8,03,108.00

1 Nos. 250 Amp MCCB 25 KA LSIG having S/C, E/F O/C protection,

R,Y,B Phase indication Lamp with control MCB

On, Off, Trip Status Indication with control MCB - -

Inbuilt Zone Slelective Interlocking function

Multifunction Meter

1 Nos. 300 Amp FP busbars of aluminium alloy as per SLD. - -

40 Nos. 32 Amp DP MCB 10 KA

On, Off, Trip Status Indication with control MCB - -

Flats DB +Spare

36 Nos. Single Phase Energy Meter - -

Short Circuit Breaking capacity should not less than 10 KA. - -

RELAYS AS PER SLD - -

Supply of aluminium conductor PVC insulated armoured served sheathed

cables 1100 Volts grade on cable tray as directed by engineer incharge

56 complete in all respect including The armouring of the cable shall be MR - -

properly connected with the earth conductor by clamps etc.

Supplying and making end termination with brass compression gland and

aluminium lugs for following size of PVC insulated and PVC sheathed /

XLPE aluminium conductor cable of 1.1 KV grade as required.

Laying and fixing of one number PVC insulated and PVC

60 sheathed / XLPE power cable of 1.1 KV grade of following size 10.8

on cable tray as required.

a Upto 35 sq. mm (clamped with 1mm thick saddle) 10.8.1 550.00 Meter 53.00 29,150.00 -

Above 95 sq. mm and upto 185 sq. mm (clamped with 25/40x3mm MS flat

Providing, laying and fixing following dia RCC pipe NP2 class

(light duty) in ground complete with RCC collars, jointing with

cement mortar 1:2 (1 cement : 2 fine sand) including trenching

(75 cm deep) and refilling etc as required. 300mm Dia

Supplying and laying of following size DWC HDPE pipe ISI marked along

with all accessories like socket, bend, couplers etc.

conforming to IS 14930, Part II complete with fitting and cutting,

jointing etc. in the existing trench, complete as required

Grand Total (DSR+MARKET BASED ITEM) 2,52,87,060.06

Grand Total (DSR+MARKET BASED ITEM) 2,52,87,060.06

Grand Total (DSR+MARKET BASED ITEM) In Lac 252.87

Grand Total (DSR+MARKET BASED ITEM) In Lac 252.87

Detailed Estimate Based On DSR-2025 With Cost Index & Market Rate

Project - Proposed Construction of Integrated Township at Chandrapura, Jharkhand.

Name Of Work -Executive Residence Block (G+6) Floor Manual Fire Detection Alarm System Work

Rate as per D.S.R. 2025 (For without

GST DSR rates = Rate*0.755)

Sr.No. Particulars Sch.No. Qty Unit Amount Rate Amount

Supplying, installation, testing & commissioning of manual call

boxes of MS construction in surface/recess with stainless steel

1 chain & hammer assembly complete with glass and push button 28.1.3 21 Each 513.00 10,773.00

etc. as required.

Supplying, installation, testing & commissioning fire alarm

sounder with facility to make announcement, mounted in M.S.

box (16 SWG) with hinged cover plate & suitable for operation

with amplifier i/c line matching transformer etc. complete as

Supplying, installation, testing & commissioning talk back slave -

station in surface/recess suitable for operation on simplex

mode complete with P.T.T. knob & speaker/microphone enclosed

3 in a M.S.(16 SWG)/ ABS box with break glass in front etc. 28.1.8 3 Each 963.00 2,889.00 -

complete as required

Supplying, installation, testing & commissioning sector panel

suitable for following zones, complete with visual indications for

short circuit fault, open circuit fault, fire condition and all other

standard facilities as per IS:2189 with mimic diagram for all

area/zone covered, complete with all connections,

interconnections as required

CABLING & WIRING -

Sr.No. Particulars Sch.No. Qty Unit Amount Rate Amount

17.5.1 Supplying & laying of 2x1.5 sqmm fire survival armoured

cable, 600/1000V rated with annealed copper conductor having

glass mica fire barrier tape covered by an extruded layer of Cross

5 Linkable Ethylene Propylene Rubber (EPR) insulation and LSZH 28.5.1 630 Meter 386.00 2,43,180.00 -

inner bedding, steel wire armouring & LSZH outer sheath

complete as required

Grand Total (DSR+MARKET BASED ITEM) 2,79,250.00

Grand Total (DSR+MARKET BASED ITEM) 2,79,250.00

Grand Total (DSR+MARKET BASED ITEM) 2,79,250.00

Grand Total (DSR+MARKET BASED ITEM) 2,79,250.00

Detailed Estimate Based On DSR-2025 With Cost Index & Market Rate

Project - Proposed Construction of Integrated Township at Chandrapura, Jharkhand.

Name Of Work -Executive Residence Block (G+6) CCTV Surveillance System Work

Rate as per D.S.R. 2025

Sr.No. Particulars Sch.No. Qty Unit Amount Rate Amount

Supplying and fixing of following sizes of medium class PVC conduit

along with accessories in surface/recess including cutting the wall and

making good the same in case of recessed conduit as required. 25mm

Grand Total (DSR+MARKET BASED ITEM) 2,01,600.00

Grand Total (DSR+MARKET BASED ITEM) 2,01,600.00

Grand Total (DSR+MARKET BASED ITEM) 2,01,600.00

Grand Total (DSR+MARKET BASED ITEM) 2,01,600.00

Detailed Estimate Based On DSR-2025 With Cost Index & Market Rate

Project - Proposed Construction of Integrated Township at Chandrapura, Jharkhand.

Name Of Work -Executive Residence Block (G+6) Lift Work

Rate as per PAR. 2025 MARKET BASED

Sr.N Rate as per

Particulars Sch.No. Qty Unit Amount Rate Amount

Supply Installation Testing and Commissioning of lift

with power operated doors and AC variable voltage and

variable frequency controls having speed of minimum

1.5m/sec as per CPWD specifications.

Extra for provision of Lift on each additional floor PAR 2025-

Grand Total (DSR+MARKET BASED ITEM) 1,13,50,020.50

Grand Total (DSR+MARKET BASED ITEM) 1,13,50,020.50

Grand Total (DSR+MARKET BASED ITEM) 1,13,50,020.50

Grand Total (DSR+MARKET BASED ITEM) 1,13,50,020.50

Name of Project : CONSTRUCTION OF INTEGRATED TOWNSHIP AT CHANDRAPURA, JHARKHAND

Final Abstract (fire fighting)

Amount as per Amount as per Amount as per

DSR -2023 Items NS/ DSR -2025 Non -Scheduled

(A) Items (A) Items (B)

S. No. Description

I. FIRE PUMPS AND HYDRANT WORKS 7,88,094.00 -

II. PIPING FOR FIRE FIGHTING SYSTEM 49,875.61 3,03,235.00 -

III FIRE EXTINGUSHER AND HYDRANT 6,16,761.58

Grand Total A+B 17,57,966.19

Grand Total A+B 17,57,966.19

DETAILED ESTIMATE

S. NO. (FIRE DSR-

2025/NS) DESCRIPTION UNIT QTY RATE AMOUNT (IN RS.)

SUBHEAD-I(A): FIRE PUMPS AND HYDRANT WORKS (NON SCHEDULED ITEMS)

1 27.4 FIRE ROOF PUMPS - ELECTRICAL

Supplying, installation, testing and commissioning of electric driven

terrace pump suitable for automatic operation and consisting of

following, complete in all respects, as required: (Terrace Pump)

Horizontal type, multistage, centrifugal pump of cast of iron body and

bronze impeller with stainless steel shaft, mechanical seal conforming to

Suitable HP squirell cage induction motor TEFC type suitable for

operation on 415 volts, 3 phase, 50 Hz, AC supply with IP55 class of

protection for enclosure, horiziontal foot mounted type with Class-'F'

insulation, conforming to IS-325.

M.S fabricated, common base plate, coupling, coupling guard,

foundation bolts etc. as required.

Suitable cement concrete foundation duly plastered and with anti

vibration pads.

Providing & fixing of pressure switch in M.S. pipe line including

2 27.22 connection etc. as required. Each 1 1,670.00 1,670.00

3 27.20 Supplying and fixing air vessel made of 250 mm dia, 8 mm thick MS

sheet, 1200 mm in height with air release valve on top and flanged

connection to riser, drain arrangement with 25 mm dia gun metal wheel

valve with required accessories, pressure gauge and paintingwith

synthetic enamel paint of approved shade as required. Each 1 19,402.00 19,402.00

4 Supply, installation, testing, trial run and commissioning of hydrants all

complete as required and as approved

Fire Hose Cabinet

Supplying and fixing single headed internal hydrant valve with

instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast

iron wheel ISI marked conforming to IS 5290 (Type -A) with blank

5 27.9 Gunmetal/Stainless Steel cap and chain as required :

27.9.2 Single headed Stainless steel Each 21 6,632.00 1,39,272.00

Supplying and fixing first-aid Hose Reel with MS construction spray

painted in post office red, conforming to IS 884 complete with the

6 27.17 following asrequired.

20 mm nominal internal dia water hose thermoplastic (Textile

reinforced) type -2 as per IS: 12585

20 mm nominal internal dia gun metal globe valve & nozzle.

Drum and brackets for fixing the equipmets on wall.

Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe

Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia

male and female couplings duly bound with GI wire, rivets etc.

7 27.16 conforming to IS 636 (type-A) as required :

27.16.2 Stainless steel (Grade 304) Each 44 4,667.00 2,05,348.00

Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm

nominal internal diameter size nozzle conforming to IS 903 suitable for

instantaneous connection to interconnect hose pipe coupling as required

27.18.2 Stainless steel (Grade 304) Each 21 3,402.00 71,442.00

Supplying and fixing orifice plate made out of 6 mm thick stainless steel

(Grade 304) with orifice of required size to be fitted between flange &

landing valve of external and internal hydrants to reduce pressure at the

outlet to the level of 3.5 kg/cm2 complete as required. Each 21 1,436.00 30,156.00

Supplying and fixing of fire brigade connection of cast iron body with gun

metal male instantaneous inlet couplings complete with cap and chain as

reqd. for suitable dia MS pipe connection conforming to IS 904 as

11 27.19 required :

TOTAL C/F TO SUMMARY 7,88,094.00

SUBHEAD-I (B): PIPING FOR FIRE FIGHTING SYSTEM

Excavating trenches of required width for pipes, cables, etc including

excavation for sockets, and dressing of sides, ramming of bottoms, depth

upto 1.5 m including getting out the excavated soil, and then returning

the soil as required, in layers not exceeding 20 cm in depth including

consolidating each deposited layer by ramming, watering, etc. and

12 disposing of surplus excavated soil as directed, within a lead of 50 m :

All kinds of soil

2.10.1.2 Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia. Cum 1 376.906145 376.91

Civil 4.5 Providing and fixing up to floor five level precast cement concrete string

or lacing courses, copings, bed plates, anchor blocks, plain window sills,

shelves, louvers, steps, stair cases, etc. including hoisting and setting in

position with cement mortar 1:3 (1 Cement : 3 coarse sand), cost of

required centering, shuttering and finishing smooth with 6mm thick

cement plaster 1:3 (1 Cement : 3 fine sand) on exposed surfaces

1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20mm

Civil 4.5.1 nominal size). Cum 1.00 10815.48853 10,815.49

Constructing masonary chamber 90 x 90 x100 cm. inside with 75 class

designation brickwork in cement mortar 1:5 ( 1 cement : 5 fine sand) for

sluice valve with CI surface box 100 mm top dia. 180 mm bottom dia.

And 180 mm deep (inside) with chained lid and RCC top slab 1:2:4 mix ( 1

cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

necessary excavation foundation concrete 1 :5 :10 (1 cement : 5 fine

sand : 10 graded stone aggregate 40 mm nominal size and inside

plastering with 1:3 (1 cement : 3 coarse sand) 12 mm thick finished with

a floating coat of neat cement complete as per standard design with FPS

Providing and fixing C.I. double acting air valves of approved quality with

bolts, nuts, rubber insertions etc. complete ( The tail pieces, tapers etc. if

15.0 Civil 18.59 reqd. will be paid separately) 0

TOTAL C/F TO SUMMARY 49,875.61

SUBHEAD-II (B):PIPING FOR FIRE FIGHTING SYSTEM

Supplying, fixing, testing & commissioning of double flanged sluice valve

of rating PN 1.6 with non rising spindle, bronze/gun metal seat, ISI

marked complete with nuts, bolts, washers, gaskets and conforming to IS

16 27.12 780 of following sizes as required :

Providing, installation, testing and commissioning of stainless steel

Ystrainer fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet

17 27.15 with 3 mm dia holes with stainless steel flange.

Providing, installation, testing and commissioning of non-return valve of

following sizes confirming to IS: 5312 complete with rubber gasket, GI

18 27.14 bolts, nuts, washers etc.as required :

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6

rating with bronze/gunmetal seat duly ISI marked complete with nuts,

bolts, washers, gaskets conforming to IS 13095 of following sizes as

19 27.11 required :

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe

conforming to IS 3589/IS:1239 including Welding, fittings like elbows,

tees, flanges,tapers, nuts bolts, gaskets etc. and fixing the pipe on the

wall/ceiling with suitable clamp/support frame and painting with two or

more coats of synthetic enamel paint of required shade complete as

20 27.7 required : (Above Ground)

Threaded joint upto 50mm diameter pipe.

Welded joint above 50mm diameter pipe.

c 27.7.8 150 mm nominal bore (class C) Rm 10 4,299.00 42,990.00

d 27.7.7 100 mm nominal bore (class C) Rm 40 3,077.00 1,23,080.00

e 27.7.6 80 mm nominal bore (class C) Rm 10 2,277.00 22,770.00

g 27.7.4 50 mm nominal bore (class C) Rm 7 1,557.00 10,899.00

J 27.7.1 25 mm nominal bore (class C) Rm 7 920.00 6,440.00

TOTAL C/F TO SUMMARY 3,03,235.00

SUBHEAD- III (B): FIRE EXTINGUSHER AND HYDRANT (NON SCHEDULED ITEMS)

Providing and fixing carbon-di-oxide type fire extinguishers consisting of

welded M.S. cylindrical body, internal discharge tube, discharge nozzle,

suspension bracket, conforming to IS 2878, finished externally with red

enamel paint and fixed to wall with brackets complete with internal

1 NS-1 charges.

Providing & Fixing of stored pressure Fire Extinguisher ABC powder type

(Mono Ammonium Phosphate Powder) Magnetic Pressure Gauge having

the facility to check at site, Discharge Time less than 9 Secs, Controllable

discharge mechanism, Range minimum 4 Meters, applicable on Class

A,B,C and electrically started Fire, A Rating- 21A, B Rating 55B as per BS

EN-3 BIS 15683 marked, Can Construction : Deep drawn & CO2 Mig

welded, Valve Construction : Forging & Machining, Internal Coating of

Can : Epoxy Powder coating, External Coating ofCan : Epoxy Polyster

Powder coating, Sheet metal thickness : 1.60MM, Helium LeakDetection

2 NS-2 Tested, Warranty.

Providing and fixing angle iron (40 mm x 40 mm x 5 mm) MS door frame

900x2100 door capable of accommodating fire hose reel, landing valve,

hose pipes, fittings & accessories. The door shall have a front glass with

lock and key arrangement & shall be painted with post office red colour

(approval shall be taken on the basis of submitted sample before

ordering) Cost of fire extinguishers not included in item rate. (Liasioing

with civil contractor for making 900x600x2100 Recessed type mansoary

3 NS-3 box (by civil contractor). Each 21 13,524.56 2,84,015.69

4 NS-4 Providing and fixing of Fire Axe Each 21 644.03 13,524.56

5 Providing, fixing, testing and commissioning of full way level

operated forged brass ball valve of brass body with forged brass

hard chrome plated steel ball tested to a pressure not lass than 15

kg/sq.cm with threaded/flanged complete with nuts, bolts,

gaskets, washers etc. as required complete as per direction of

NS-5 Engineer incharge.

6 NS-6 ROOF FIRE PANELS:

Supply, installation, testing and commissioning of followingintegrated,

cubicle type,dead front, extensible, sheet steel control panel. The panel

shall be suitable for 440 volts, 50 cycles, 4 wire supply Item 1 55,835.33 55,835.33

The following components and accessories shall be mounted with ineach

One no 100 amps TP incoming MCCB with the following:

0-500 volts 96 x96 square mm voltmeter with slector switch and control

0-100 amps 96 x96 square mm ammeter with CT's and slector switch- 1

Including all elecal works

Phase indicating lamp with toggle switches.

Indication lamps for ON/OFF/TRIP status

Outgoing Feeders / Starters as below:

100 ATP MCCB with star / delta as starter suitable for 30 HP motor for

Downcomer Pump - 1 Set

Provision in control panel to connect flow switch for autmatic operation

of roof fire pumps.

TOTAL C/F TO SUMMARY 6,16,761.58

PROPOSED CONSTRUCTION OF EXECUTIVE HOSTEL BUILDING FOR CTPS TOWNSHIP AT CHANDRAPURA,

S.No. Description Unit Qty RATE Amount

# EXTERNAL SIGNAGES

1 MAIN GATE SIGNAGES

Providing and fixing External Signage's made of SS 304 (brush finish) 1mm thk.sheet for Logo and letters with raising(letter

depth of 50mm). Including all fittings, accessories, fixtures, fabrication.The signage will be front illuminated/hollow

illuminated either back or front of the signage to be made of 3.5 mm thick acrylic. 3M/Avery/LG Cast vinyl 90 micron and 5

7 sq meter Nos. 0 327647 0.00

years warrenty for desired colour with OSRAM make Or equivalent/ approved list of Make LEDS and IP 67 Grade OSRAM

powersupply with 5 years warrenty fixed on the wall with necessary fixtures. Height of a letter is not less than 400 mm. (IN

HINDI + ENGLISH + LOGO)

2 Entry/ Exit Signage - Wall / Surface Mounted IN/OUT/NO ENTRY/ NO EXIT)

Providing and fixing IN/OUT lit Mounted Exterior Signage sides is to be made of 80 mm width, extruded alloy 6063 of

having no screws visible outside. duly anodized 18-20 microns champagne/ brown/ silver finish with in built in provision to

received the sign face panel in 4.5mm Acrylic on front and having provoison of hold the LED Modules . Sign face is to be

made of graphic plotter cut vinyl 90 micron and 5 year warrenty as per graphic pasted over 4.5mm thick white transluent 600 450 Nos. 1 12824.24 12824.24

acrylic. The panel should be made easily openable for maintinace point of view.

Illumination:- The lighting for panel shall be achieved through OSRAM make Or equivalent/ approved list of Make LEDs

and IP 67 Grade OSRAM powersupply.

3 CAMPUS DIRECTIONAL TOTEM SIGNAGE

Providing and fixing Signage side to be made of 80 mm width modular extrude alloy 6063 of brand 247 sign/cosign/vista

system having no screw visible outside powder coated to 40-50 microns with in built in provision to receive the sign face

panel in acrylic/ACP on both side. Sign face B is to made of 10 thick Acrylic with 2 mm thick laser cut acrylic letters on it.

Internal Frame is to be made of 50x50x3mm MS Section with base plate of thickness 10mm. The panel should be made easily

openable for maintaince point of view. 18mm thick grounting bolt for holding base palte of totem.

FOUNDATION WILL BE PROVIDED BY CLIENT.

4 Traffic regulatory Signage ( Drop off/ Speed Limit / No Horn/ BASEMENT Entry/Exit)

Providing and fixing Traffic Regulaotry Non lit Totem Signage, made from Following

A)POST :- Signage is to be made oF 100x100 mm 1800 mm High MS pole, Base Plate of size 250x250mm of thickness

10mm is to be used. Duly powder coated 50 microns in the desired colour.

B) Panel-1 :-Panel size 400X110X1200mm is to be made of 50x50x2mm internal MS frame duly powder coated to 40-50

microns with ACP 4 mm thick, 0.5 mm aluminium foil, 3M / AVERY Prismatic Retro reflective sheet and approved color 600 1900 Nos. 0 41473 0.00

Overlay film on top having desired text and pictographs on both side post.

C) Panel-2 :- Panel size 600X600 Sq/round with ACP 4 mm thick, 0.5 mm aluminium foil, 3M / AVERY Prismatic Retro

reflective sheet and approved color Overlay film on top having desired text and pictographs.

FOUNDATION WILL BE PROVIDED BY CLIENT.

INTERNAL SIGNAGES

5 BLOCK NAME SIGNAGES (NON - ILLUMINATED)

Providing and fixing External Signage's made of SS 304 (brush finish) 1mm thk.sheet for Logo and letters with raising(letter

depth of 50mm). Including all fittings, accessories, fixtures, fabrication.The signage will be front illuminated/hollow

illuminated either back or front of the signage to be made of 3.5 mm thick acrylic. 3M/Avery/LG Cast vinyl 90 micron and 5

years warrenty for desired colour with OSRAM make Or equivalent/ approved list of Make LEDS and IP 67 Grade OSRAM

powersupply with 5 years warrenty fixed on the wall with necessary fixtures. Height of a letter is not less than 400 mm.

a Shop office banks 8.5 sq meter Nos. 3 469472 1408417.32

6 GENERAL INSTRUCTION SIGNAGES 0

Signage to be made of stainless steel sheet of 1 mm thick 304 grade brush finish including engraving/ etching of letters of

required size filled with colour as desired by engineer,fixing with ss screws on walls. signages to be bilingual/trilingual 0

b No Littering 300 400 Nos. 4 3616 14462.08

d Instructional Signages 600 900 Nos. 1 16264 16263.94

7 AREA IDENTIFICATION SIGNAGES 0

Supply & installation Signage Made Of Base 3 MM Beton silveri Beton whitel Swiss snow finish ACP panel Box having 6063

Alloy profiles to house the edge of ACP with in groove. Profile size 18X38 mm @edges and to be eprotuded by 5mmx3mm

beyond side surface from front side to make teh surface appeared recessed. Powder coated I Anodised as per approved shade,

Fascia 3mm acrylic sheet to be Stuck on base ACP Sheet in staggered manner before fixing of signage then Content CNC Cut 0

Acrylic 2 mm thick fixed on signage facia. signage to be mounted using clamps at backside of profile. teh sheets and content

to be duly CNC cut with neat and clean polised edges. Profiles make to be 247SIGN/ Tata Elexi / Glo-lite.Or equivalent/

approved list of Make

a Room Identification/ Room Name 300 250 Nos. 12 3523 42281.76

c Department Name Identification 300 500 Nos. 12 6027 72329.28

d Washroom Mounted 250 200 Nos. 12 2641 31690.08

g Floor Level Lift 300 500 Nos. 12 6027 72329.28

8 AREA IDENTICATION WAYFINDER SIGNAGES 0

Supply & installation Signage Made Of Frame work of 25 mm x 38 mm 6063 Alloy profiles (PVDF Coated) having (Roman

Ogee) Edge and panel made of 4 MM exterior grade PVDF coated ACP. Frame to house the edge of ACP with in groove.

Content CNC Cut Acrylic 2 mm thick fixed on signage facia. signage to be mounted using clamps at backside of profile, No 0

screws to be visible. Profiles make to be 247SIGN/ Tata Elexi / Glo-lite.Or equivalent/ approved list of Make

a Washroom wall projected (Double sided) 300 210 Nos. 4 5094 20376.24

b Wayfinding signages (Double sided) 1200 250 Nos. 1 19761 19761.46

c Reception Sign (Single sided) 900 175 Nos. 4 7131 28522.96

d Waiting area (Single sided) 900 175 Nos. 2 7131 14261.48

9 Wayfinder sign for basement 0

Double sided signage will be fabricated using 13+13 mm twin thick ultra slim edge modular aluminium extruded profile with

approved ACP as base duly fixed over on both side and type IV reflective vinyl duly digitally cut and pasted on ACP panels on 1050 200 Nos. 4 10311 41243.36

both side. Signage will be hanged using SS csble/ SS chain with fastners.

10 Entry Area Identification Signs for Ramp 0

Single side signage will be fabricated using 13-14 mm thick ultra slim edge modular aluminium extruded profile with

approved ACP as base duly fixed and type IV Avery/3M reflective vinyl duly digitally cut and pasted on ACP panels.

11 FIRE EVACUATION PHOTOLUMINICENT SIGNAGES 0

Emergency Evacuation Signage :‐ Round Corner signages with radius 8 to 12 mm, made of 2 mm Rigid PVC sheet with

premium photoluminescent of illumination upto minimum 4 hours. With UV printing for Graphic and text. Adhering to latest 0

NBC Standards. Mounted using SS screws OR 3M VHB tape, as per directions of Engineer-in-charge.

b Stair direction at landing 300 125 Nos. 4 819 3275.68

c stair floor level Indicator 382 382 Nos. 4 3193 12772.32

d Fire safety disclaimer 300 300 Nos. 4 1977 7906.00

e Fire hose cabinet 150 200 Nos. 4 658 2633.76

g Fire extinguisher 150 200 Nos. 4 658 2633.76

12 Evacuation Route Identification 0

Sandwich Acrylic frame work of 5 mm + 5mm thickness. Signages made of premium photo luminescent of illumination upto

minimum 4 hours. With UV printing for Graphic and text. Adhering to latest NBC Standards. Mounted using SS Spacers 18 15 450 Nos. 2 8868 17735.40

mm x 25 mm, as per directions of engineer incharge. Signages to be bilingual /trilingual language.

13 Poster Frame 0

Poster frame made of alloy 6063 having copper/bronze anodizing, clip on arrangement for easy change of insert. Use 2mm

clear acrylic as a protection layer in the front. 600 900 Nos. 3 10795 32383.92

BRAND / MAKE- 247SIGN/ COSIGN/ VISTA System.Or equivalent/ approved list of Make

G.Total 2027727.34