SPECIAL REPAIR TO BLDG NO P 126 (JCOs MD ACCN) AT BALWANT LINE AT CMP CENTRE AND SCHOOL AND PROVN OF ONE X BATH ROOM NEAR GUARD ROOM UNDER GE (SOUTH) BANGALORE

Amount

M&L for Roughening surfaces of old concrete floor by picking, sweeping clean and washing, Brushing neat cement slurry with 3.0kg of cement per sq. metre complete all as specified

M&L non-skid coloured ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over a screed of 15mm thick in CM 1:6 etc complete all as specified and directed.

M&L Non skid coloured ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in skirting etc. set and jointed in neat cement slurry and pointed in white cement or coloured cement to match over 10 mm thick rendering in cement mortar 1:4 etc complete all as specified and as directed.. Note : The width of tiles 100 mm to be cut from full size of tiles as directed by Engineer-in-charge.

M&L for bull nosed coloured chequered cement mortar tiles 20-25mm thick staircases/steps in single piece for steps and landings, set jointed and complete all as secified pointed in neat cement slurry in floor over a screed of 15mm thick in CM 1:6 etc complete all as specified and directed.

Dismantling floor hearth/ stone slabs/mosaic tile flooring or wall tiling including cement mortar bedding (but not backing) and removing servicebale tiles to stores and rubbish off rubbish off the same out side the MD land complete all as specified and as directed.

M&L for non-skid coloured ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and incl screed bed of 15mm thick in CM 1:6 etc complete all as specified and directed.

S&F coloured glazed ceramic tile in vertical surface 300x450x7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 10 mm thick rendering CM 1:4 backing coat complete all as specified and as directed.

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10cm girth complete all as specified.

S & F in repair of CPVC pipes 25mm Incl. SDR 11 Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors including taking down of pipe of 20 mm GI pipe complete all as specified.

S & F in repair of CPVC pipes 20mm all SDR 11 Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors including taking down of pipe of 15 mm GI pipe complete all as specified.

S&F of 20 mm dia CPVC brass elbow complete all as specified and as directed.

S&F of 20 mm dia CPVC Brass Tee complete all as specified and as directed.

S&F of 20 mm dia male brass threaded adapter complete all as specified and as directed.

S&F of 20 mm dia female brass threaded adapter complete all as specified and as directed.

S&F 1000 Ltrs. Capacity rotational moulded polyethylene water storage tanks (cylinder vertical with class top) hoisted and fixed in position including dismatling and removing to store all as specified

S&F 25 mm bore nipple suitable for HDPE water tank. (Min wt 45 gms).complete all as specified.

Supplying and laying in repairs CPVC ball valve( Gate valve) 25mm dia complete all as specified.

S&F 25 mm internal bore Ball valve high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Minimum weight 25mm-450gms) complete, fixed in repairs, all as specified.

Supplying and laying of CPVC Union 25mm dia complete all as specified.

S&F in repairs vitreous china wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) 'P' or 'S' trap complete all as specifed and as directed.

S&F in repairs plastic water closet seat cover, White, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specifed and as directed.

S&F in repair PVC white low level flushing cistern 10 ltr capacity with all fittings syphonic action with inlet ball valve and float, handle, bracket PVC short bend/ long bend etc. complete all as specified and directed .

S&F in repair Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified.

S&F in repair vitreous china wash hand basin, white, Oval type size 520 x 450x200mm including one number brass CP waste coupling, brackets 2 numbers including cutting for and pinning in ends of brackets complete all as specified and directed.

S&F in repair 32mm waste pipe for WHB & sink complete all as specified and as directed

S&F in reapir 15 mm bore brass CP two way bib taps with crutch or butterfly handle,screwed down,screwed for pipe or for brass ferrule complete all as specified.

S&F in repair 15 mm bore diameter brass CP wall mixture any type complete all as specified and as directed.

S&F in repair 75mm dia PVC (SWR) floor/Nahani trap, plain with 100mm SS grating including solvent cement incl dismantling of old any type Nahani/floor trap and also necessary filling s requeired complete all as specified and as directed.

S&F pillar taps, tall height brass,fancy type, chromium plated, screwed down high pressure with or without lettered 'Hot' or 'cold' with long screwed shanks and flynuts screwed for 15mm bore iron pipe and fixed in repair, complete all as specified and directed.

S&F in repairs angle valves 15 mm nominal bore, brass, chromium plated, complete, fixed in repairs, all as specified and directed.

S&F in repairs PVC connection 15 mm size , 600mm long with PTMT adopter,check nuts and washer on both sides for hot water complete all as specified.

S&F in repair Pressure adjustable shower rose 15mm of brass chromium plated with shower arm of 190mm Long Light Body complete all as specified and directed.

S&F in repairs SS soap dish, any type, fixed to plugs with chromium plated brass screws complete all as specified and as directed.

S&F in repair for Glass stainless steel corner Shelf Complete all As specified

S&F in repair Cabinet Mirror 300mmX 450MM complete all as specified.

S&F in repair tubular towel rail 600 mm long of brass chromium plated 20 mm dia D type 60 cm long fixed with two plugs (gutties) of 2nd class hard wood embedded in cement mortar 1:3 with MS screws complete all as specified.

S&F in repairs PVC (SWR) 110 mm bore pipes single socketed, in any length with rubber ring joints laid in floors complete all as specified and as directed.

S&F in repairs PVC (SWR) 75 mm bore pipes single socketed, in any length with rubber ring joints laid in floors complete all as specified and as directed.

S&F PVC bends any radius 75mm dia complete all as specified and as directed.

S&F PVC bends any radius 110mm dia complete all as specified and as directed.

S&F PVC Single T any radius 110 mm dia with access door complete all as specified and as directed.

S&F PVC (SWR) 110 mm vent cowl complete all as specified and as directed.

S & F in repair PVC (SWR) pipes 110mm dia single socketed in any length with rubber ring joints fixed to walls including dismantling and breaking of pipe and fittings complete all as specified and as directed.

S&F in repair PVC (SWR) pipes 75 mm size in bore single socketed , in any length with rubber ring joints, fixed to walls including dismantling and breaking of pipe and fittings complete all as specified and as directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) not exc 1.5 sqm etc complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) exc 1.5 sqm but n exc 4 Sqm etc complete all as specified and directed.

Taking down of shutters exc 1 sqm but n exc 2 Sqm etc complete all as specified and directed.

S&F for Framed work such as grills,gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165etc. complete, as specified,

S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet, reinforced with MS square tube and fixing in position with hold fast, complete all as specified and directed by Engr-in-Charge.(Cost of hold fast included in the unit rate of this item.) complete all as specified.

S&F Factory made solid panel PVC moulded door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.

S&F 30 mm thick factory made Flush shutters, solid core construction, with particle board core and plywood face panels,complete all as specified.

S&F 30 mm thick IInd class hard wood glazed and skelton shutters open rebated and prepared to receive glass , gauge etc divided in to squares with plain, chamfered or rounded mittered and rebated sash bars any numbers, edges of framing plain chamfered complete all asspecified.

M&L second class plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed

S&F 2nd class hard wood plain fillets, Square or rectangular or triangular in section, clean sawn, planed on both sides secured with nails or beads , sectional area n exc 3 Sqcm including two coats of synthetic enamel paint over a coat of pink wood primer complete all as specified.

S&F continuous (Piano) hinges, mild steel, bright finish or electro galvanised width of flaps 30 mm when open complete all as specified.

S&F MS 40mm dia, drawer/cupboard knobs fixed with nut, screw and washer of brass polished, bright finished complete all as specified.

S&F 100 mm long Hasp and staple, safety type, aluminium anodised with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all specified.

S&F 75 mm brass handles,cast type polished bright complete all as specified and directed.

S&F cold rolled mild steel butt hinges medium weight of size 100mm fixed Complete all as specified and as directed.

S&F cold rolled mild steel butt hinges medium weight of size 125mm fixed Complete all as specified and as directed.

S&F 250 mm long aluminium alloy anodised sliding door bolt with hasp staple (bolt type) and fixing clips of sheets cast or extruded sections or cast aluminium alloy complete all as specified.

S&F 150 mm size extruded aluminium alloy handles fabricated type with plate anodized complete all as specified.

S&F 150 mm long aluminium anodized barrel tower bolts of extruded section complete all as specified.

M&L for preparation of new or previously untreated wood and wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant complete and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). all as Specified.

S & F for 18/ 19 mm thick prelaminated particle board interior grade, prelaminated both sides with decorative type with screws incl PVC edge bidding confirming to IS 12823-1990 complete all as specified

S&F in repairs mild steel 150 mm helical door springs including roller and roller plate complete (Helical door spring) including welding to steel chowkhats if required all as specified.

S&F for floor door stopper(double) of aluminium alloy body and tongue anodised with hard drawn steel spring fixed to door overall length of cover plate 150mm complete all as specified.

S&F Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples

Supply and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge

Supply and fixing Powder coated aluminium window shutters, sliding type 3 track aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified

S&F sheet glass ordinary quality 4mm thick in square not exc 0.5 Sqm complete all as specified.

S&F 4 mm thick figured glass pin headed type and glazing with oil putty in square n.exc 0.50 Sqm in each pane complete all as specified.

M&L for rendering 10mm thick in CM 1:6 on fair face of brick or concrete surfaces of walls finished even and fair Including taking down, raking out joints, hacking for key, scrubbing down with water etc and removing rubbish of the premises and applying two coats of oil bond distemper over a coat of 1mm thick wall care puttyafter preparation of surface complete all as specified and as directed.

M&L for washing, rubbing and brooming for preparation of existing surface and cleaning with water of old painted surfaces of walls and applying two coats of oil emulsion distemper over a coat 1 mm thick wall care putty, including stopping of nail holes, filling of cracks, etc and cleaning all window panes from splashes / droppings, complete all as specified and directed.

M&L for preparation of old decorated /painted surfaces of ceilng and applying one coat of oil emulsion distemper all as including cleaning splashes of distmeper on floor/objects etc all as specified and directed.

M&L 18-20 mm thick Granite black colour including rounding edges to exposed portion as in platforms for wash hand basin / sink (table, rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like laid in cement mortar (1:4),10mm thick incl pointing in white cement (1:2) using mable dust with admixture of pigments to match with shade granite including cutting for securing of slab,including after dismantling of existing any type of stone or concrete etc complete all as specified and as directed.

S&F in repairs 15mm dia swan neck pillar tp for sink brass fancy type, chromium plated complete all as specified

S&F in repair sinks with drainage board made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes coupling; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and directed.

S&F in repairs kitchen plate rack made of stainless steel 1mm thick complete size 1200 x 700mm x 200mm width of trade pattern complete all as specified.

Excavation in trenches, not exceeding 1.5 M wide and not exceeding 1.5 M depth for foundation, etc. and nexc 10 sqm on plan and getting out in soft/loose soil and disposal of surplus soil upto n.exc. 50m distance complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick with soils complete all as specified and as directed.

Spreading and levelling in layers not exceeding 25 cm thick and well ramming including watering as required complete all as specified and as directed.

M & L Plain Cement Concrete 1:4:8 Type D-2 using 40 mm graded crushed stone aggregate in foundations, filling and mass concrete complete all as specified and as directed.

M & L Reinforced Cement Concrete 1:1 1/2 :3 Type A-1 using 20 mm graded crushed stone aggregate in foundations including rafts, footings and mass concrete complete all as specified and as directed.

M & L Reinforced Cement Concrete 1:1 1/2 :3 Type A-1 using 20 mm graded crushed stone aggregate) in columns complete all as specified and as directed.

M & L Reinforced Cement Concrete 1:1 1/2 :3 Type A-1 using 20 mm graded crushed stone aggregate as in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and as directed.

Reinforced Cement Concrete1:1 1/2 :3 Type A-1 using 20 mm graded crushed stone aggregate) in slab supported on walls and beams and shelves like complete all as specified and as directed.

M&L for Providing precast cement concrete 1:3:6 type C-1 using 20mm graded stone aggregate set in CM 1:4 solid building blocks exc. 10 cm in width and setting in cement mortar in walls laid in CM 1:6 complete all as specified and as directed.

Mild steel TMT bars 10 mm dia., and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips complete all as specified and as directed.

All as per item no.10 above but 6 to 8mm dia complete all as specified and as directed.

Mild steel TMT bars 5 mm to 10 mm dia., cut to length, bent to shape required, in stirrups, spacers and binders and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips complete all as specified and as directed.

S & F framed work such as grills, gratings etc. with ends of bars shouldered or riveted or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walkways, railings, framework of water tanks and similar works conforming to Fe-290 Gde E-165.

Form work to sides of fdn and PB for rough finished surfaces of concrete complete all as specified and as directed.

Form work to columns for fair finished surfaces of concrete complete all as specified and as directed.

Form work to sides and soffits of beams (roof beam) for fair finished surfaces of concrete complete all as specified and as directed.

Form work to sides and soffits of suspended slab for fair finished surfaces of concrete complete all as specified and as directed.

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. complete all as specified and as directed.

S&F Powder coated anodised aluminium frame, for door, windows, ventilators runner & packing with rubber gasket etc, with one or more rebates including joinning cleat for rebates including joining cleats for fixing etc, complete all as specified & directed by Engineer-in-Charge.

Blank

S&F 100 mm long extruded aluminium alloy handles, fabricated type anodised complete all as specified and as directed .

S&F mild steel butt hinges 75 mm, medium weight cold rolled and fixed complete all as specified and as directed.

M&L for rendering 10 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 and finished smooth and even without using extra cement.

M&L for rendering 5 mm thick CM 1:4, over 10mm thick in CM 1:6 on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement including mixing of water proofing compound, finishing the surface fair and even.

M&L for rendering 5 mm thick in ceiling on fair faces of concrete surfaces in cement mortar 1:3 and finished smooth and even without using extra cement.

M & L 25mm thick PCC (1:2:4) Type B-0 using 12.5mm graded stone aggregate as in sub-base of floor

Supply only liquid water proofing compound complete all as specified and as directed.

M & L 75 mm thick Cement concrete type D2, 1:4:8 (using 40 mm graded crushed stone aggregate) in sub base of flooring/ hard standing complete all as specified and as directed.

M & L 50 mm thick PCC 1:2:4 type B1 (using 20 mm graded crushed stone aggregate) in floorings including finishing the surface even and smooth using without extra cement complete all as specified and as directed.

M&L for preparing newly plastered surfaces of ceilings and applying three coats of white wash complete all as specified and as directed.

M&L for newly plaster surfaces of walls and applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm incl all necessary safety norms to the workers complete all as specified and as directed.

M &L for preparation of new plastered surface and applying two coats of cement base paint over cement primer on walls complete all as specified and as directed.

M & L two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer over 10cm in width or girth not otherwise described after preparation of new or previously untreated steel surface

S&F vitreous china wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) complete all as specifed and as directed.

S&F plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specifed and as directed.

S&F 15mm dia stop vlave cast copper alloy screwed down high pressure with crutch or buterfly handle chromium plated screwed both ends for iron pipe or unions and fixed for 15mm bore pipe concealed type complete all as directed.

S & F 15mm dia brass chromium plated shower rose125mm dia

S&F PVC low level flushing cistern 10 ltr capacity, valveless, syphonic action type with inlet, ball valve float and handle incl brakcet and flush pipe 32 mm dia complete all as specifed and as directed.

S&F Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified.. (Cat Part No of Cera F8030105 AB or equivalent in parryware/hindware/prayag)

S&F vitreous china wash hand basin, white, flat back size 550 x 400 mm including one number brass CP waste coupling, waste pipe 32 mm dia, brackets 2 numbers including cutting for and pinning in ends of brackets complete all as specified and directed.

S & F 15mm dia pillar taps cast copper alloy with capstan heads, chromium plated, screwed down high pressure without lettered 'HOT' or 'Cold" with long screwed shanks and fly nuts, screwed for iron pipe and fixed.

S&F brass CP 15 mm bore two way bib cock, quarter turn with wall flange and aerator, complete all as specified and as directed.

S&F 75mm dia PVC (SWR) floor/Nahani trap, plain with CP grating including solvent cement complete all as specified and as directed.

S&F 110mm dia PVC (SWR) 'P' trap complete all as specified and as directed.

S & F 100mm dia PVC (SWR) bends with oval access door

S & F 100mm dia PVC (SWR) bends

S & F 75mm dia PVC (SWR) bends with oval access door

S & F 75mm dia PVC (SWR) bends

S & F 110mm dia PVC (SWR) reducers

S & F 75mm dia PVC (SWR) vent cowls

M&L for 75 mm PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors

M&L for 75 mm PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls

M&L for 100 mm PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors

S&F 1000 Ltrs. Capacity rotational moulded polyethylene water storage tanks (cylinder vertical with class top) hoisted and fixed in position complete all as specified

S & F 20 mm dia CPVC ball valves complete all as specified.

S&F 20 mm bore Ball valve high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Minimum weight 20mm-210gms) complete, fixed in repairs, all as specified.

S&F CPVC pipes SDR 11 & plain CPVC SDR 11 fittings of 20mm dia laid on walls / ceiling or laying in floors complete all as specified.

S&F CPVC pipes SDR 11 & plain CPVC SDR 11 fittings of 16mm dia laid on walls / ceiling or laying in floors complete all as specified.

S & F 20mm brass tank adaptor

S & F 15mm brass elbow

S & F 15mm brass Tee

S & F 15mm brass male threaded adaptor

S & F 15mm brass female threaded adaptor

S&F 15mm dia fancy type chromium plated angle valve screwed both end for iron pipe or for unions , high pressure with long shank & cup (concealed type) having crutch handle complete all as specified and as directed by Engineer-in-Charge.

PVC connections 15mm size with PTMT nuts of length 450mm all as specified.

M&L 20 mm thick screed bed or bedding layer in cement mortar 1:4 for laying floor finishing complete all as specified .

M&L 20 to 25 mm thick coloured glossy finished factory made PCC designer tiles/pavers, set and jointed & pointed in neat cement slurry as in path/floor etc complete all as specified.

S&F towel rail 600mm long brass CP fixed with and including chromium plated brass screws and wooden/plastic cleats complete all as specified and as directed.

Soap dish, any type, fixed to plugs with chromium plated brass screws

M&L for cleaning the plastered/concrete surfaces with wire brushes and applying water proofing treatment as under: (a) Apply bitumen primer at the rate of 0.27 litre per Sqm as per IS 3384-1986 and bonding bitumen of VG-10 @1.20 Kg per Sqm. (b) APP modified water proofing memebrane as per IS 16540/16532-2017, 3mm thick and weighing not less than 3.80 kg per Sqm reinforce polyster/HMHDPE matt black finish over compatible primer/bonding bitumen and finish the top surface with bituminus aluminium paint @0.10 Ltr per Sqm complete all as specified.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. Removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc.

M & L for point wiring with 1100 Volts grade 1.5 sqmm PVC insulated FRLSH unsheathed cable with multistandred copper conductor conforming to IS: 694:1990 (for Phase, Neutral and and Earth) in and including Non metalic PVC rigid condiut medium grade with ISI mark of appropriate size with all accessories laid in wall/ ceiling/floor etc, concealed with GI flush in box/terminal boxes of sutaible size, including front plate for mounting of modular switch/ socket and combined cover plate with fitting screw washer, including cutting chasses in wall/floor/roof for fixing of conduit and flush in box and making good the distributed surfaces matching with existing complete all as specified and as directed for following- One light/ Bell/ fan point controlled by one switch

All as per Item No 154 above here in before but for Modular type Socket 6/10 Amp of two module in independent board, 230 volts complete all as specified and directed by Engr-In-Charge.

All as per Item No 154 above here in before but for Modular type Socket 6/10 Amp of two module on same board, 230 volts complete all as specified and directed by Engr-In-Charge.

All as per Item No 154 above here in before but for Modular type additional light / fan point on the same switch circuit mounted on same switch board controlled with separate switch, 230 volts complete all as specified and directed by Engr-In-Charge.

All as per Item no 154 above here in before but with 2.5 sqmm PVC insulated FRLSH unsheathed cable with GI Flush in box for modular switch/ socket 16 Amps of sutaible size as required with front plate for mounting of modular switch/ socket and combined cover plate of as required at site complete all as specified and as directed by Engr-in-Charge.

S&F for modular switch piano, flush type single pole, one way 16 Amps, 230 Volts complete all as specified and directed by Engr-In-Charge.

S&F for Modular type Socket 6/16 Amp two way of 230 volts complete all as specified and directed by Engr-In-Charge.

S&F for modular switch piano, flush type single pole, one way 5/6 Amps, 230 Volts complete all as specified and directed by Engr-In-Charge.

S&F for Modular type Socket 6/10 Amp of two way point complete all as specified and as deirected by engr in charge

S&F for Modular type fan regulator 1/2 module as reqd, 230 volts complete all as specified and directed by Engr-In-Charge.

S&F for Modular type bell push switch one way 6/10 Amps, 230 volts matching with existing complete all as specified and directed by Engr-In-Charge.

S&F Call bell AC, 230 Volts matching with existing sample complete all as specified and directed by Engr-In-Charge.

M&L ceiling rose surface bakelite 65x50 mm two to three terminals.complete all as specified and as directed by Engr-In-Charge.

Supply and fixing of LED lamp 9W including driver holder Complete all as specified and as directed by Engr-In-Charge.

M & L for lamp holder , PVC/ Polycarbonate type with back plate sutaible for LED 9W lamp fittings Complete all as specified and as directed by Engr-In-Charge.

M&L sub main wiring surface type with two runs of single core, PVC insulated, unsheathed multi standard copper conductor cable of size 10 Sqmm, 1100 volts grade (FRLS) and one run of 10 Sqmm PVC insulated multi stranded copper conductor for earth continuity conductor drawn through concealedin wall PVC conduit complete all as specified and as directed by Engr-In-Charge. (Note :- Two runs of 10 Sqmm cable, one run of 10 Sqmm continuity earth wire and one run of PVC conduit with all necessary accessories will be measured as one length).

S & F in replacement VTPN DB - Dobule Door made out of CRCA mild steel sheet flushed in wall, TPN 4 way with 200 Amp rated bus bar, 415 volt with PVC MCB blanking plate, stove enamelled for incorporated of MCBs, insulators and MCCB of capacity upto 125 Amps TP/FP etc, complete all as specified and as directed by engineer in charge

Supply and fixing MCCB FP 415 Volts 100 Amps, 16 KA complete all as specifed and directed by Engr-In-Charge.

S&F MCB, DB double door type, made out of CRCA mild steel sheet flushed in wall, SPN 8 way with 200 Amps rated bus bar , 240 volts IP-43, with PVC MCB blanking plates, stove enamelled, dust and vermin proof suitable for incorporation of MCB's and isolators etc including complete all as specified and as directed complete all as specified and as directed by Engr-In-Charge.

Supply and fixing MCB SPN 40 Amps, 240 Volts complete all as specified and as directed by Engr-In-Charge.

Supply & fixing MCB SP 06-40 Amp, AC, 240 volts, complete all as specified and as directed by Engr-In-Charge.

Supply and fixing surface & wall mounted LED batten 4feet with extruded aluminium housing and robust construction 20 W system lumen including flexible copper 2 core wire from tube light fitting to ceiling rose required length with all accessories all as specified and directed by Engr-in-Charge.

Supply and fixing surface & wall mounted LED batten 2feet 10 W with luminious efficacy not less than 100 lumen/watt including flexible copper 2/3 core wire from tube light fitting to ceiling rose with mounting provisions and all accessories with color of light warm white/cool day light as reqd at site complete all as specified and directed by Engr-in-Charge.

Taking down unserviceable ceiling fan, wall mounted fan, cabin fan, exhaust fans etc of any type and size from position, disconnecting electric supply, repair/replacement of unserviceable items, including cleaning oiling/greasing,tightening of nut bolt and refixing matching with existing. complete all as specified and directed by Engr-In-Charge. Note: (a) Cost of Replacement of minor items i.e, nut bolts, screws, pins etc including T&P and grease/oil are deemed to be included in quoted rates. Major items to be replaced to make fans serviceable will be measured and paid seperately.

Supply only following items to be fixed under item no -177 complete all as specified and directed by Engr-In-Charge. Ball/Roller bearing of size and shape matching with existing suitable for ceiling fan

Supply only following items to be fixed under item no -177 complete all as specified and directed by Engr-In-Charge. Ball/Roller bearing of size and shape matching with existing suitable for Exhaust fan

Gun metal bush of size and shape matching with existing suitable for ceiling fan

Gun metal bush of size and shape matching with existing suitable for Exhaust fan

Motor stator for ceiling fans wounded with copper wire of size matching with existing with insulation with casing complete.

Motor stator for exhaust fans upto 250 mm sweep wounded with copper wire of size matching with existing with insulation and casing matching with existing complete.

Motor rotor prewired for ceiling fans of size and type matching with existing

Motor rotor prewired for Exhaust fans/wall mounted fans of size and type matching with existing

Fan blades for ceiling fan of any type and size matching with existing

Fan blade for exhaust fan metal body any type and size with mounting provisions matching with existing.

Plastic cup with screw for ceiling fans

Rubber bush with MS bolts, nuts & washers with 'U' clamps for ceiling fans complete all as specified and as directed.

S&F in replacement capacitor 2.5 Mfd suitable for ceiling / exhaust /wall mounting fans complete all as specified and as directed.

S&F in replacement down rod of 30/45 cm with nut, bolts and safety pin for ceiling fans complete all as specified and as directed.

M&L for Preparation of surface & painting the ceiling fans with blades complete after cleaning & applying one coat of stove enamelled white paint by spray painting, writing No complete all as specified & as directed by Engr -in-Charge.

M&L for Preparation of surface & painting the Exaust fans with blades complete after cleaning & applying one coat of stove enamelled white paint by spray painting, writing No complete all as specified & as directed by Engr -in-Charge.

Taking down, dismantling of geysers of any type/capacity from site for repair and Inspection, cleaning, descaling, brazing inner tank, internal wiring including replacement of unserviceable items as reqd, reassembling & reinstallation after necessary repair incuding testing after repair complete all as specified & directed. Note :(a) Replacement of major unserviceable items shall be measured & paid separately under respective item of work.. (b)Cost of replacement for minor items like washers, gaskets, nuts, bolts etc and items not mentioned below is deemed to be include in quoted rates.

Supply only following items to be fixed under item no -182 complete all as specified and directed by Engr-In-Charge. Inner tank for geyser of capacity 25 ltrs of shape matching with existing.

Siphon Assembly suitable for geyser of capacity 25 ltrs of shape matching with existing.

Heating element rated 1.5/2.0 KW with mounting provisions round/tikona as reqd of shape matching with existing

Thermostat with auto cutoff provision switch capillary/screw type, with range 0-80 deg celcius of shape and size matching with existing suitable for geyser of capacity 25/50 Ltrs.

Indicator lamp red and green with coloured diffuser for geysers matching with existing.

Safety valve/high pressure valve matching with existing for geysers

NRV for geysers matching with existing.

Base fixing cover matching with existing.

Cover outer for geyser of capacity 25/50 ltrs of shape and size matching with existing.

S&F in replacement meter box, Size not less than 200mm x 150mm x 100mm, fabricated out of sheet steel, wall mounting meter box suitable for mounting 1 nos energy meters of size matching with existing, concealed type, painted with stove enamelled paint over a coat of red oxide primer on 2.0mm thick sheet steel, weather proof with double stud hinged door front open with internal locking arrengement and externally locking arrengement with aldrop bolt and meter mounting sheet sutaible size should be fixed inside box including dismantling old meters and cutouts from old box and refixing energy meter with complete connection in new meter box complete all as specifed and as directed by Engr-In-Charge.

M & L earthing complete with GI earth plate Electrode 60 cm x 60 cm x 6 mm thick burried directly in ground (earth plate not less than 2.25 Metre deep below ground level) with top edge of the plate not less than 1.5 metre below normal ground level connected to galvanished earth wire 4.0 mm dia by means of bolts, nuts check and washers of GI or steel all as shown in electrical plate No. 3 of SSR Pt -I connected to earthing test point all as specified or indicated including GI pipe 15 mm dia light grade for earth wire protection, necessary excavation, earth work in any type of soil, PCC chamber and RCC cover slab, connecting lead wire from test point to DB complete all as specified & as directed by Engr-In-Charge.

S&F LED weather proof bulk head light fitting of shape and size as per site requirment of wattage upto 10 watt light fitting with mounting clamp, LED driver holder, LED lamps etc including connecting up to in celling rose complete all as specified and as directed by Engr-in-Charge.

Supply and laying 40 mm GI pipe fitting tubes medium grade galvanished with all fittings complete laid in trenches including taking down the old unserviceable GI pipe from trenches Complete all as specified and as directed by Engr-In-Charge.

Supply and laying 25 mm GI pipe fitting tubes medium grade galvanished with all fittings complete laid in trenches including taking down the old unserviceable GI pipe from trenches Complete all as specified and as directed by Engr-In-Charge.

S & F in repairs float valves of size 25 mm and as reqired at site as complete brass fitting with rod and plastic ball Complete all as specified and as directed by Engr-in-in Charge.

S & F in repairs gun metal gate valve with inner wheel head, screwed both ends in iron pipe and fixed of Size 25 mm Complete all as specifed and as directed by Engr-In-Charge.

Supply, laying and testing cable XLPE insulated, screened, PVC bedded galvanised steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16 Sqmm x 4 core including taking down unserviceable UG cable complete all as specified and directed by Engr-In-Charge.

Removing excavated soil to a distance not exceeding 50 mtrs and depositing where directed at a level not exceeding 1.5 M above the starting point all as directed.

M&L for sand cushioning in trenches for bricks of u/g cable with coarse sand laid dry in trenches with uniform thickness complete all as specified and as directed by Engr-In-Charge.

Supply and lay burnt bricks of sub class 'B' laid dry across in trenches for cable protection all as specified and directed Complete all as specified and as directed by Engr - In - Charge.

Supply, laying and testing cable XLPE insulated, screened, PVC bedded galvanised steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 10 Sqmm x 2 core complete all as specified and directed by Engr-In-Charge.

Supply and laying GI medium grade GI tubing complete with all fittings laid in trenchs / wall of size 25mm dia complete all as specified and as directed.

Cutting screwing existing GI pipe upto 50mm for inserting Tee pieces, bends, sockets etc for taking out new connection complete all as specified and as directed.

S & F 25mm dia gun metal gate valve with inner wheel head, screwed both ends in iron pipe and fixed complete all as specified and as directed.

S & F Float valve of 25mm dia complete all as specified and as directed.

M & L switch piano, flush type single pole, one way 5 Amps complete all as specified and as directed.

S & F Metal Body sound proof exhaust fan 450mm size made of sturdy engineering plastic complete with louvers shutter, voltage 230V, 50Hz, RPM 1200, copper winding of sweep 450mm complete all as specified and as directed.

S&F MCB, DB double door type, made out of CRCA mild steel sheet flushed in wall, SPN 4 way with 200 Amps rated bus bar , 240 volts IP-43, with PVC MCB blanking plates, stove enamelled, dust and vermin proof suitable for incorporation of MCB's and isolators etc including complete all as specified and as directed complete all as specified and as directed by Engr-In-Charge.

VACON INFRASTRUCTURES (BID ID -3269298)

SKANDA CONSTRUCTIONS (BID ID -3276837)

Elite Constructions (BID ID -3274545)

PRAGATHI BUILDERS (BID ID -3277007)

K. VENKATESH NAIDU (BID ID -3277188)