SPECIAL REPAIR TO OFFR MD ACCN QTR NO P-45, P-67/1 AT HQT ROAD, SPL REPAIR TO HARDSTANDING IN FRONT OF BLDG NO P-25, P-26, P-33, P-34, P-35, P-45, P-51, P-52, P-66, P-67 AT HQT ROAD AND PROVN OF IRON LADDER AND PATH FOR CERTAIN BLDGS IN FAUJI ROAD,HM

Amount

Schedule 'A' Part-I (B/R Works)

Surface excavation n. exc. 30cm deep and averaging 15cm deep in soft/loose soil complete all as specified and as directed.

Excavation in trenches not exc. 1.5 m wide and n. exc. 1.5m in depth for foundation, etc, or for shafts, wells, cesspits, manholes, pier holes etc. and getting out in hard/ dense soil complete all as specified and as directed.

Removing surplus spoil to a distance exc. 1.5 km but n.exc 5km and depositing where directed at a level n. exc. 1.5 m above the starting point complete all as specified and directed.

Material and labour for cement concrete 1:4:8 type D-2 using 40mm graded crushed stone aggregate as in sub base/foundation filling/mass concrete/sunken floor etc, complete all as specified and as directed.

Supply and fixing mild steel such as grills gratings, etc. with ends of bars shouldered and/or or forged into spikes; framed riveted,guard bars; barred iron doors ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165 and similar works including one shop coat of zinc chromate primer and cutting holes/making surface good in cement concrete 1:2:4 type B-0 complete all as specified and as directed.

Material and labour for mild steel high yield strength TMT bars 10mm dia and over cut to length bent to shape required, including cranking, hooking ends, bending and binding with and including MS wire (annealed) not less than 0.9mm dia complete all as specified and as directed.

Material and labour for preparation of new or previously untreated steel surface of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Material and labour for cement concrete 1:2:4 type B-1 using 20mm graded crushed stone aggregate as in sub base/foundation filling/mass concrete/sunken floor, benching, coping, roof kerb or mud stops for foot path etc etc, complete all as specified and as directed.

Material and labour for 100mm thick plain cement concrete 1:4:8 type D-2, using 40mm graded crushed stone aggregate as in sub-base for floors, surface finished even and rough to receive top finish complete all as specified and as directed.

Material and labour for chequered cement concrete tiles 25cm x 25cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors laid over and including 20mm thick screed bed or bedding layer in cement mortar 1:6, set and jointed in neat cement slurry and pointing in white cement with pigment to match complete all as specified and directed.

Demolition of cement concrete (Unreinforced) of any description in ground floor and paving not exceeding 15 cm in thickness (below or above ground level) complete all as specified and as directed.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc. and brushing neat cement slurry with 3.0kg of cement per sq. metre complete all as specified and as directed.

Taking down steel shutter of any description exc 2 sqm each complete all as specified and directed.

Supply and fixing steel rolling shutter 1.25mm thick with bevel gear box & crank handle including top cover ,anchoring rod ,hasp and staple and one shop coat of primer; erected in position as indicated ,complete gear operated type with bevel gear box and crank handle all as specified and directed.

Supply and fixing steel rolling shutter 1.25mm thick without ball bearing as specified including top cover ,anchoring rod ,hasp and staple and one shop coat of primer ;erected in position as indicated ,complete gear operated type with bevel gear box and crank handle complete all as specified and directed.

Supply and fixing framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing Fe 410-W (Gde- E- 250) quality complete all as specified and as directed.

Supply and fixing Mild steel, plain black sheet in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required complete all as specified and directed.

Material and labour for 100mm thick cement concrete 1:2:4 type B-1 using 20mm graded crushed stone aggregate as in sub base floor finishing cement concrete surface as specified and directed.

Material and labour for sand filling under floors or in foundation including consolidation with plate vibrator before and after laying paver blocks etc complete all as specified and as directed.

Material and labour for 80 mm thick, machine pressed precast concrete (white) interlocking paver block M-40 grade, any shape and size, conforming to IS 15658-2006, with grey cement and no pigment, complete all as specified and as directed.

Taking down chowkhat or frames with shutter not exceeding 1.5sqm each with shutters (without taking off shutters from the frames) and removing to or from store complete all as specified and as directed.

Taking down chowkhat or frames with shutter exceeding 1.5 sqm not exceeding 4.0sqm each with shutters (without taking off shutters from the frames) and removing to or from store complete all as specified and as directed.

Taking down shutters of any description exc 1 Sqm and not exc 2 sqm complete all as specified and directed.

Supply and fixing 2nd class hardwood plain solid straight chowkhat or frame, wrought framed rebated on the solid, rounded or chamfered put together with flue pinned at joints etc and in position complete all as specified and directed.

Supply & fixing of solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS Square tube, supplying & fixing in opening as per specification & drawing complete all as specified and directed.

Supply and fixing for factory made solid PVC moulded door shutter, 28 to 30mm thick (stiles) with 2,4 or 6 raised panel with wood free EPS design with 2mm thick moulded prelam PVC sheet on the front face and 2mm plain colour PVC sheet on back face complete all as specified and directed.

Supply and fixing 18-19 mm Prelaminated particle board, exterior grade, prelaminated both side with decorative choice lamination & fixed with screws to timber frame work complete all as specified and directed.

Material and labour for 35mm thick plain framed, panelled shutters (two panels), with lock rail and panels of 9mm thick BWP commercial ply or of venered particle board 12mm thick with commercial veneering on both faces with rails and style of 2nd class hard wood. The size of rail and stile as per IS: 1003 (Part-I), kiln seasoned and chemically pressure treated complete all as specified and directed.

Material and labour for 2nd class hard wood glazed and skeleton shutters 35mm thick, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc., sizes of members of shutters as specified in clause 8.24 (a) of SSR Part-I; supplied and fitted to chowkhats complete all as specified and directed.

Material and labour for 35mm thick factory made flush shutter solid core construction with block board core and plywood face panels commercial type on both sides complete all as specified and as directed.

Supply and fixing for steel window 1.25 mm thick box type (primer coated) ERW hollow P section of size 60mmx25mm single rebated comprises gauged skeleton shutter ERW sec 50mmx20mm and 1mm thick with two openable leaf consisting two Nos sash bars of T-section 20mmx3mm complete welded to frame with one verticle mulion of ERW box type T-section of size 60mmx25mm and 1.25mm thick incl cutting holes and making good dismantled portion PCC (1:2:4) type B-1 four Nos for each window) including following fittings welded to frame shutter: - (a) Hold fast, 150mm long of 12mmx3mm made to shape-04 Nos per window. (b) Handle of z section 20mmx25mm, 100mm long 01 Nos per leaf (c) MS tower bolt 150mm long-2 Nos per leaf (d) z section 20mmx25mm, 100mm long stopper - 01 No per leaf (f) MS pintal hinges of size 75mmx12mm- 2 Nos per leaf (g) Fabrication & fixing arrangement as per Drg No CEJZ/TD-06/07. Note: Wire mesh and painting shall be measured and paid separately under respective item of schedule.

Supply and fixing for steel window 1.25 mm thick box type (primer coated) ERW hollow P section of size 60mmx25mm single rebated comprises glazed skeleton shutter ERW sec 50mmx20mm and 1mm thick with two openable leaf consisting two Nos sash bars of T-section 20mmx3mm complete welded to frame with one verticle mulion of ERW box type T-section of size 60mmx25mm and 1.25mm thick incl cutting holes and making good dismantled portion PCC (1:2:4) type B-1 four Nos for each window) including following fittings welded to frame shutter: - (a) Hold fast, 150mm long of 12mmx3mm made to shape-04 Nos per window. (b) Handle of z section 20mmx25mm, 100mm long 01 Nos per leaf (c) MS tower bolt 150mm long-2 Nos per leaf (d) z section 20mmx25mm, 100mm long stopper - 01 No per leaf (f) MS pintal hinges of size 75mmx12mm- 2 Nos per leaf (g) Fabrication & fixing arrangement as per Drg No CEJZ/TD-06/07. Note : Glass pans and painting shall be measured & paid separately under respective item of schedule.

Supply and fixing galvanized mild steel wire cloth 0.56mm nominal dia and average width of aperture 1.18mm and fixed with tinned tacks or galvanised steel staples complete all as specified and as directed.

Supply and fixing sheet glass 3mm thick ordinary quality and glazing with oil putty or wooden beads not exceeding 0.5 Sqm in each pane, complete all as specified and directed.

Material and labour 4mm thick figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sq. m in each pane complete all as specified and directed.

Supply and fixing butt hinges, 100mm long, medium weight, cold rolled mild steel complete all as specified and as directed.

Supply and fixing 200mm long aluminium anodised barrel tower bolt, of extruded section, with bright bolt and fixed complete all as specified.

Supply and fixing extruded aluminium alloy handles, 150mm size, fabricated type, anodised complete all as specified and directed.

Supply and fixing 300mm, mild steel ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and as directed.

Supply and fixing 250mm long aluminium alloy, anodised, sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed all as specified and directed.

Material and labour for preparation of new or previously untreated wooden surface of any description not otherwise described over 10cm width or girth and applying one coat of synthetic enamel paint over a coat of pink primer all as specified and as directed.

Supply and fixing in repair floor door stopper (double) of aluminium alloy body and tongue, anodised with hard drawn steel spring fixed in floor overall length of cover plate 150mm complete all as specified.

Material and labour for 25mm dia mild steel pipe curtain rod, powder coated fixed with & including MS powder coated hooks/ brackets and decorative finials (at both side), shade as approved by GE complete all as specified includng fixing of long size rawl plugs in wall for MS hook complete all as specified and directed.

Dismantling, floor hearth or wall tiling including cement mortar bedding (but not backing), removing rubbish outside defence land complete all as specified and as directed.

Material and labour vitrified ceramic tiles 10mm thick, any shade as approved, polished area of each tiles n.exc. 0.36 Sqm (square / rectangular) in floor etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles with & including rendering 15mm thick in cement mortar (1:6) finished rough to fix tiles complete all as specified and directed.

Material and labour vitrified ceramic tiles 10mm thick, any shade as approved, polished area of each tiles n.exc. 0.36 Sqm (square/ rectangular) in vertical surfaces such as skirting/ dado, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles laid over & including rendering 10mm thick in cement mortar (1:4) complete all as specified and directed.

Material and labour for glazed ceramic coloured tiles of size 450 x 350 x 7mm thick as in vertical surfaces i.e. skirting/ dado set and jointed in neat cement slurry and pointed in white or coloured cement to match the existing surface with & including rendering 10mm thick in cement mortar (1:4) finished rough to fix tiles complete all as specified and directed.

Material and labour for Non skid ceramic coloured tiles 7 to 8mm thick (Square or rectangular) area of each tile exc 0.06 Sqm but not exceeding 0.11 Sqm as in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles laid over and including screed bed or bedding layer 15mm thick in cement mortar (1:6) for laying floor finishes complete all as specified and directed.

Material and labour for 20mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all specified and as directed.

Material and labour for 50 mm thick PCC (1:3:6) type C-2 using 40 mm graded stone aggregate as in plinth protection, laid in panels, concrete surfaces finished even & smooth without using extra cement complete all as specified and directed.

Demolition of brick work built in cement mortar including all quoins, arches, pillars etc complete all as specified and directed.

Material and labour for brick work with sub class 'B' bricks, old size, straight or curved on plan to any radius in half brick thick walls, built in cement mortar (1:4) complete all as specified and directed.

Taking down cement plaster of any description on brick or concrete surfaces etc. including raking out joints, hacking for key, scrubbing down with water etc. complete all as specified and as directed.

Material and labour for 15mm thick rendering in cement mortar 1:6 on brick work or concrete surfaces finished even and smooth without using extra cement complete all specified and as directed.

Material and labour for 15mm thick rendering in cement mortar 1:4 on brick work or concrete surfaces finished even and smooth without using extra cement complete all specified and as directed.

Material and labour for 5mm thick rendering in cement mortar 1:3 on brick work or concrete surfaces of ceiling finished even and smooth without using extra cement complete all specified and as directed.

Material and labour for preparation of new plastered or unplastered surfaces of walls and applying two coats of oil bound distemper white or tinted over a coat of birla white putty complete all as specified and as directed.

Material and labour for preparation of newly plastered surfaces of walls and applying two coats of cement base paint over a coat of primer complete all as specified and directed.

Material and labour for prepration of surface and applying three coats of white (lime) wash on new surface of ceiling complete all as specified and as directed.

Taking up or down 15mm bore steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and as directed.

Supply, laying, jointing and testing 15mm bore galvanized iron steel tubing medium grade with all fittings such as bends, elbows, sockets, tees, reducers etc, fixed to walls, ceiling or laid in floors, including cutting through wall complete all as specified and as directed.

Taking up or down 20mm bore steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and as directed.

Supply, laying, jointing and testing 20mm bore galvanized iron steel tubing medium grade with all fittings such as bends, elbows, sockets, tees, reducers etc, fixed to walls, ceiling or laid in floors, including cutting through wall complete all as specified and as directed.

Cutting chases, pinning in, making good to facing where reqd and pointing in CM 1:3 to ends of edges of landing etc and cutting chases for concealed water tubing and making good cutting exc 10 cm but n.exc 20 cm girth complete all as specified and directed.

Supply and fixing in repairs for 15mm dia of pipe bib taps, cast copper alloy and chromium plated screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed.

Supply and fixing in repair 15mm bore stop valve/ angle cock cast copper alloy chromium plated screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for union complete all as specified and as directed.

Supply and fixing in repairs 15mm dia cast copper alloy chromium plated fancy type WHB mixer tap for hot and cold water complete all specified and as directed.

Supply and fixing 15mm bore dia concealed/Angular stop valves chromium plated fancy type, screwed down , high pressure ,with lettered Hot and Cold with long screwed shanks and fly nuts screwed for iron pipe or for union and fixed complete all as specified and directed.

Supply and fixing in repair 450mm long PVC connection fiber reinforced, for Hot/Cold water 15mm size with PTMT nuts and washer on both ends complete all as specified and as directed.

Supply and fixing in replacement PVC white low level flushing cistern 10 ltr capacity with all fittings syphonic action with top push type button with inlet ball valve and float including flush pipe, ball valve, handle, bracket PVC short bend etc. complete all as specified and directed.

Supply and fixing in repairs plastic water closet white seat cover closed pattern with flat bottom cover and mild steel chromium plated or aluminized hinging device complete all as specified and directed.

Supply and fixing in repair vitreous china wash down water closet pan (pedestal pattern), white, and connection to drain (or outgoing pipe) and connection to flushing pipe, anti-syphonage pipe, (excluding flusing cistern and flush pipe) etc complete all as specified and as directed.

Supply and fixing in repair Orissa pattern squatting pan with integral foot rest, vitreous china white of size 580mm x 440mm including making connection to trap, flush pipe, antisyphonic pipe (but excluding flushing pipe and flushing cistern), provision of lime concrete bedding etc and making good the floor surface complete all as specified and directed.

Supply and fixing vitreous china wash basin, coloured, oval shape, counter type of size 550mm x440mm fixed on RCC with granite platform including brackets and waste coupling (32 mm dia PTMT),waste pipe etc,cutting for pinning in ends of brackets fixing completely all as specified and directed. Make: Hindware cat no: 10016 or equivalent in as per Appendix 'B' of Particular Specification. Note:(i) RCC and granite shall be measured and paid seperately.

Supply and fixing in repair brass chromium plated shower rose of 125mm size, with or without swivel joints including fixing to steel pipe or union complete all as specified and as directed.

Supply and fixing in repair sink with drainage board made out of stainless steel sheet 1mm thick (kitchen or laboratory) with pIngs, washers and wastes; including bedding in cement mortar in dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 915mm x 460mm, bowl size 410mmx 330mmx 160mm complete all as specified and as directed.

Supply and fixing in repair PVC kitchen cabinet (dark shade) of size 280cm x 75cm and 30cm deep made of solid PVC plain coloured board 19mm thick comprising of two vertical portion and two horizontal shelves with four ball catchers shutters fixed with 75mm size galvanised mild steel butt hinges two Nos in each pane, aluminium handle 125mm long including taking down existing wooden/ block board/ PVC kitchen cabinet complete all as specified and as directed.

Supply and fixing elegant art frame type black synthetic wood bath mirror on piece length 54cm x 42cm fixed to wall complete all as specified and directed.

Supply and fixing Glass corner shelf (three tire) including CP railing, radius 300 mm complete all as specified and directed by the Engr-in-Charge.

Supply and fixing in repairs Chromium plated grating 125mm dia circular of approved make and fixing with cement mortor 1:3 on Nahani trap or floor trap complete all as specified and directed.

Supply and fixing in repairs toilet cabinet made out of white acrylic sheet 1.50 mm thick of size 450 x 350 x 90 mm with looking mirror 450 x 300 mm or specified fixed on the shutter and with suitable shelving arrangement in replacement of existing wooden cabinet/ mirror and repairing the disturbed surface to match with existing complete all as specified and directed.

Supply and fixing in repairs Pre fabricated stainless steel plate rack of size 9100mm x 790mm x 250mm, made out of 1mm thick stainless steel plate jointed with brass screws complete all as specified.

Supply and fixing for rotational moulded polye- thylene water storage tanks, 500 litres capacity, (cylindrical vertical with closed top), ISI marked, hoisted and fixed in position in SSR Part-I, including dismantling of water tanks complete all as specified and directed.

Supply and fixing for rotational moulded polye- thylene water storage tanks, 1000 litres capacity, (cylindrical vertical with closed top), ISI marked, hoisted and fixed in position in SSR Part-I, including dismantling of water tanks complete all as specified and directed.

Supply and fixing in replacement 20mm bore ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe (Minimum weight 210 gms) complete all as specified and directed.

Supply and fixing in repair brass chromium plated tubular towel rail, 20mm dia, 'D' type, 60cm long between flanges fixed with brass chromium plated screws complete all as specified and as directed.

Supply & fixing in replacement 32mm dia PVC waste pipe for WHB complete all as specified and as directed.

Supply and fixing 15mm bore superior quality jet spray brass chromium plated alongwith PVC connection of 1.0 meter suitable for EWC complete all as specified.

Material and labour for complete removal of existing treatments by washing, rubbing down and stopping etc on wall surface and applying two coats of oil bound distemper over a coat of primer complete all as specified and directed.

Material and labour for complete removal of existing treatments by washing, rubbing down and stopping etc on old surface of ceiling surface and applying two coats of white (lime) wash complete all as specified and directed.

Material and labour for complete removal of existing treatments by washing, rubbing down and stopping etc on wall surface and applying two coats of cement base paint over a coat of primer complete all as specified and directed.

Demolition and breaking up drain pipes of dia n.exc 150 mm internal dia (Salt glazed ware, AC or Reinforced concrete) set in cement mortar complete all as specified and directed.

Supply and fixing 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

Supply and fixing PVC (SWR) bends any radius 110mm bore complete all as specified and directed.

Material and labour for 75mm PVC (SWR) floor trap plain with grating incluidng jointing with solvent cement fixed in repairs complete all as specified and directed.

Supply and fixing 110mm bore PVC (SWR) branch pieces, single (single Y) equal or unequal, complete all as specified and as directed.

Demolition of cement concrete (reinforced) of any description in any position not otherwise specifically provided for (below or above ground level) including reinforcement cut as required to faciliate demolition complete all as specified and directed.

Material and labour for repairing of RCC projections, chajjas, roofs, facia etc. in patches not exceeding 3 Sqm in each patch by necessary preparation i.e. scrapping, cutting, chiseling, derusting and cleaning exposed reinforcement, sufaces of damaged, loose RCC surfaces and applying one coat of cement slurry and filling the surfaces with cement concrete (1:1.5:3) using 12.5mm graded crushed stone aggregate and reinforced with welded mesh of weight exc 2kg per sqmtr but n.exc 3kg/sqm with or without facia and finished with cement sand mortar (1:3) using coarse sand in patches are n.exc 70mm including applying two coats of finishes to match with the existing surfaces in at any height complete all as specified. Note:- Cost of formwork and welded mesh shall be deemed to be included in unit rate quoted by the contractor complete all as specified and as directed.

Material and labour for precast reinforced cement concrete 1:2:4, type B-1 using 20 mm graded crushed stone aggregate as in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs,mangers, shelves and similar articles with plain faces in position and set in cement mortar 1:6 including necessary form work complete all as specified and directed.

Material and labour for Cleaning/clearing of sewer line under ground of any depth by removing any type of blockage including desilting, descaling and de-chocking from drain manually using roding by any means and flushing after cleaning/clearing of sewage line of 150 mm dia bore pipe.The entire sludge water shall be disposed off out of Defence land complete all as specified and directed by Engineer-in-Charge.

Schedule 'A' Part-II (Internal electrification)

Taking down carefully aluminium / copper point wiring (light / fan / socket or power) complete including fitting such as switches, ceiling roses, socket, light fittings, regulators etc complete and making good disturbed surfaces of walls, floors complete all as specified and directed.

Taking down sub main wiring of two single core PVC cable PVC insulated 6/4 sqmm size cable including conduit or wooden batten and removing the material from site and making good the surfaces of walls, ceiling etc. all as per existing including white washing, painting all as per existing complete all as specified and as directed.

Taking down XLPE insulated, armoured screened PVC bedded, galvanised steel strip or wire armored, electric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor of any size complete all as specified and as directed.

Taking out unserviceable main switch/DB's complete all as specified and as directed.

Material and labour for concealed point wiring with 1.5 Sq.mm (nominal area) single core PVC insulated and unsheathed, FRLS cable, multi-stranded, copper conductor cable 1100 Volts grade with universal colour code (Phase & Neutral), drawn in and including PVC concealed conduit medium grade (ISI marked) with accessories like bends, tee junction boxes fixed on wall, ceiling etc. with sunk mild steel pressed terminal box 1.6mm thick sheet duly painted with two coats of black bituminous paint over a coat of red oxide primer and providing 3mm thick laminated bakelite sheet top cover including earth wire of PVC insulated FRLS cable, copper conductor multi-stranded, 1.5 Sq.mm size in green colour, for one light / call bell / fan point controlled by one, one way switch complete all as specified and as directed.

Material and labour for concealed point wiring with 1.5 Sq.mm (nominal area) single core PVC insulated and unsheathed, FRLS cable, multi-stranded, copper conductor cable 650/1100 Volts grade with universal colour code (Phase & Neutral), in and including PVC concealed conduit medium grade (ISI marked) with accesories like bends, tee junction boxes etc. with sunk pressed steel terminal boxes and providing 3mm thick bakelite sheet top cover including earth wire of PVC insulated FRLS cable, copper conductor multi-stranded, 1.5 Sq.mm size in green colour, for one three pin socket outlet 5 Amps on same board with other switches complete all as specified and as directed.

Material and labour for concealed point wiring with 1.5 Sq.mm (nominal area) single core PVC insulated and unsheathed, FRLS cable, multi-stranded, copper conductor cable 650/1100 Volts grade with universal colour code (Phase & Neutral), in and including PVC concealed conduit medium grade (ISI marked) with accesories like bends, tee junction boxes etc. with sunk pressed steel terminal boxes and providing 3mm thick bakelite sheet top cover including earth wire of PVC insulated FRLS cable, copper conductor multi-stranded, 1.5 Sq.mm size in green colour, for one three pin socket outlet 5 Amps on independent board complete all as specified and as directed.

Material and labour for concealed point wiring with 2.5 Sq.mm (nominal area) single core PVC insulated and unsheathed, FRLS cable, multi-stranded, copper conductor cable 650/1100 Volts grade with universal colour code (Phase & Neutral), in and including PVC concealed conduit medium grade (ISI marked) with accesories like bends, tee junction boxes etc. with sunk pressed steel terminal boxes and providing 3mm thick bakelite sheet top cover including earth wire of PVC insulated FRLS cable, copper conductor multi-stranded, 2.5 Sq.mm size in green colour, for one six pin socket outlet 15 Amps on independent board complete all as specified and as directed.

All as per ser item No.110 above but with 4 sq mm cable for AC on independent board complete all as specified and directed.

Supply and fixing single pole and neutral enclosure with a two pin and earth plug and socket with one single pole MCB 240Volts, 20Amps complete all as specified and as directed.

Supply and fixing switch piano flush type, 5 Amps, AC, single pole, one way, 230 Volts (ISI Marked) complete all as specified and as directed.

Supply and fixing switch piano flush type, 15 Amps, AC, single pole, one way, 230 Volts (ISI Marked) complete all as specified and as directed.

Supply and fixing switch socket outlet multipurpose flush type 5 Amps, AC, 5 pin, single pole, one way, 230/250 Volts (ISI Marked) complete all as specified and as directed.

Supply and fixing socket outlet, multipurpose flush type, 5/15 Amps, AC, 6 pin, single pole, one way, 230/250 Volts (ISI Marked) complete all as specified.

Supply and fixing electric bell, AC, 230 volts, single pole complete all as specified and as directed.

Supply and fixing ceiling rose, surface bakelite, 65mm x 50mm having 3 terminals, PVC polycarbonate and isolated body complete all as specified and as directed.

Supply and fix ceiling fan regulator electronic rotary Step type (socket type) single phase A/C 230 volts all complete as specified and directed.

Supply and fixing lamp holder, PVC/ Polycarbonate type insulated body with back plate suitable for batten fittings including 5 watts LED lamp all sheathed flexible copper conductor of size 0.75Sqmm 3 core complete all as specified and as directed.

Supply and fixing in replacement of City 1 new decorative wall light fixture made up of polycarbonate, suitable for 5 W retrofit LED lamp (including LED lamp) complete all as specified and directed.

Supply and fixing sub main wiring with two single core PVC insulated unsheathed, FRLS multi stranded copper conductor cable of size 6.0 Sqmm and one single core PVC insulated unsheathed, FRLS multi stranded copper conductor cable green colour of size 6.0 Sqmm as earth lead in and including 25mm dia PVC concealed conduit with fittings complete all as specified and as directed.

Excavation in trenches not exc. 1.5 m wide and n. exc. 1.5m in depth for foundation, etc, or for shafts, wells, cesspits, manholes, pier holes etc. and getting out in soft/loose soil complete all as specified and as directed.

Returning filling in, including, spreading, leveling and well ramming in layers not exceeding 25cm complete all as specified and directed.

Removing excavated material to a distance n exc 50 metre and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed.

Supply, fixing and laying GI tubing light grade 40 mm bore with all necessary fitting laid in trenches, under road crossing, in floors or fixed to poles/DB for cable protection etc complete all as specified and as directed.

Supply and laying XLPE insulated, armoured screened PVC bedded, galvanised steel strip or wire armored, electric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor of cross sectional area 25Sqmm, 3.5core complete all as specified and as directed.

Material and labour for sand filling in trenches for cable cushioning 8cm below and 15cm above the cable and compaction complete all as specified and as directed.

Material and labour for sub class 'B' bricks laid in trenches for cable protection complete all as specified and as directed.

Supply and fixing Sheet metal enclosure for DBs when MCBs to be used, SPN 8 ways 240 V, with 200 Amps rated bus bar, double door, epoxy coated inside and outside complete all as specified.

Supply and fixing sheet metal enclosures for MCB's, double door, distribution board triple pole and neutral 4way, 240 Volts with 200Amps rated bus bar complete all as specified and as directed.

Supply and fixing MCB's, single pole, 6 to 32 Amps, 240 Volts complete all as specified and as directed.

Supply and fixing MCB's, single pole and neutral, 32 to 63 Amps, 240 Volts complete all as specified and as directed.

Supply and fixing MCCB's, triple pole and neutral, 100 Amps, 415 Volts, 16KA breaking capacity complete all as specified and as directed.

Supply and fixing LED batten light fitting (double side) 1X22Watts LED light fixture retrofit with 2100 lumen output with internal surge protection device of 4KV with voltage band of 140-280V CRI 6500K (white light) with LED rod 22Watts with fixtures box type and making electrical connections to ceiling rose using PVC insulated and overall sheathed flexible copper conductor of size 0.75Sqmm 3 core complete all as specified and as directed.

Supply and fixing in replacement LED street light fitting 1X60Watts including lamp made of pressure die cast housed withtoughened glass and high power LED with secondary optics,aluminium IP66 protection, 6500K impact resistance of IK 07 & 10 KV(SEOUL) external surge protection device including necessary brackets, nuts, bolts and washer as required for fixing and making electrical connections to by using PVC insulated and overall sheathed flexible copper conductor of size 0.75Sqmm 3 core complete all as specified and as directed.

Supply and fixing in replacement of energy saving bulk head luminaries with opal diffuse LED 1x10 watt 6000 K power factor more than 0.90 IP-65 class-I protection with high efficiency LED electronic driver, surge protection up to 2 KV, operative on 140 volts to 270 volts AC supply complete prewired products must be made in India only connection and testing complete all as specified and directed. Make : Havells cat part no LHEOAOP7UZ6W010 or equivalent as mentioned in Appendix 'B' to particular specifications. Note: (i) Contractor shall be provided 2 years written manufacturer’s warranty for the LED fixture complete including driver from the certified date of completion. (ii) Contractor shall be produce LM-79 & LM-80 report of NABL accredited laboratory from manufacturer's.

Supply and fixing 1200mm sweep ceiling fan, AC single phase 230/240 volts and making electrical connections to ceiling rose using PVC insulated and overall sheathed flexible copper conductor of size 1.5Sqmm 3 core complete all as specified and as directed.

Supply and fixing 300mm sweep metal body heavy duty exhaust fan, AC single phase 230/240 volts with louvers/shutter with mounting brackets with suitable size of nuts, bolts, washers make opening in the wall of required size for fixing the exhaust fan and making good the disturbed wall/plastered surface and making electrical connections to ceiling rose using PVC insulated and overall sheathed flexible copper conductor of size 1.5Sqmm 3 core complete all as specified and as directed.

Material and labour for earthing complete with galvanised steel earth plate, electrode 600 x 600 x 6mm thick buried directly in ground (earth pit not less than 2.25 metre below normal ground level) with top edge of the plate not less than 1.5metres below normal ground level, connected and including GI earth lead wire 4mm dia connected to earth plate by means of nuts, bolts, check nuts and washers of galvanised iron or steel, GI earth wire protected by 15mm dia GI pipe 'light grade' upto 2 metre above ground level and connected to machinery earth plate surrounded by packed alternate layers of charcoal and common salt 15cm thick all around top and bottom and watering pipe 20mm bore GI light grade all as shown in electrical plate No 3 of SSR Part-I of 2009, testing on completion including providing PCC chamber (1:3:6) using 20mm graded stone aggregate and 50mm thick cover with RCC 1:2:4 type B-1 and 8mm dia TMT bars 100mm C/C both way and frame including excavation earthwork and returning filling etc, complete all as specified and directed. Note :- Earth pit shall be constructed 50cm from the side of excavation to avoid sinking of pit.

KABEER CONSTRUCTIONS

DUGGAL CONSTRUCTION CO

M/S Kuldip Construction Co.

G S TRADERS

PAUL CONSTRUCTION CO.

SANDEEP JHANJI CONSTRUCTIONS

NIRMAL SINGH

SARASWATI CONSTRUCTION CO

THAPAR CONSTRUCTION COMPANY

AAY KAY ENGINEERS