CERTAIN REPAIR TO OFFRS MD ACCNS UNDER AGE B/R-II OF GE (EAST) JALANDHAR CANTT

Amount

Taking down cement plaster of any description thickness including raking out joints hacking for key scrubbing down with water complete all as specified and as directed.

M&L for 15 mm thick cement mortar 1:6 on brick or concrete surface finished even and smooth without using extra cement complete all as specified and as directed.

M&L for preparing new plastered surfaces of walls by applying two coats of oil bound distemper over a coat of primer and one coat of birla white putty complete all as specified.

M&L for 15mm thick cement plaster on brick or concrete surfaces in cement mortar (1:4) mixed with integral water proofing compound in the proportion recommended by manufacturer, surfaces finished fair and even complete all as specified and as directed. (WPC shall be measured and paid separately under appropriate item of this BOQ).

M&L for preparation of new surfaces of walls including cornices, plasters etc (Plastered or unplastered surfaces) and applying two coats of cement base paint complete all as specified and as directed

Supply only integral water proofing compound all as specified and as directed.

M&L for plastering 5mm thick in cement mortar (1:3) finished even and smooth without using extra cement as on ceiling complete all as specified and as directed

M&L for three coats of white wash on newly plastered surfaces of ceiling including preparation of surfaces complete all as specified and as directed.

M&L for preparation of old surfaces of walls including cornices, plasters etc (Plastered or unplastered surfaces) and applying one coats of cement base paint complete all as specified and as directed

M&L for preparation of old decorated surfaces of walls, washing rubbing down and stooping of distempered and painted surfaces and applying one coat of oil bound distemper complete all as specified and as directed

M&L for one coat of white wash old plastered surfaces of ceiling including preparation of surface complete all as specified

M&L for hacking out old broken glass (any thickness, size quality or description) from wooden or steel frame glazed with putty or fixed with beads complete all as specified and as directed

S&F sheet glass ordinary quality 3.0 mm thick in square not exc 0.50 Sqm each pane glazing with oil putty, clip in metal frame and wooden beading in wooden frame complete all as specified

Dismantling floor hearth or wall tiling including cement mortar bedding ( but not backing) and disposal of rubbish outside MD land complete all as specified

M&L for non-skid ceramic coloured tiles 7 to 8mm thick area of each tile exceeding 18 sqm but not exceeding 38 sqm in floors set and jointed in neat cement slurry and pointed in while or coloured cement to match over and including 15mm thick bedding layer CM 1:6 in complete all as specified

M&L for coloured glazed tiles of size 450x 350x7 mm thick fixed with neat cement slurry in vertical surface to wall pointing in white/coloured cement to match over and including 10mm thick rendering in CM 1:4 complete all as specified and as directed.

M&L Vitrified Ceramic tiles light shade, 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match colour tiles over and incl 15mm thick screed bed in CM 1:6 all as specified.

All as per srl item No. 17.00 here-in-before but in skirting and 10mm thick rendering as backing coat of CM 1:4

M&L for 25mm thick cement concrete (1:2:4) type B-1 (12.5 mm graded aggregate) to receive the top layer of tiles complete all as specified and as directed

M&L for 18-20 mm thick machine cut granite (of any type ) tiles stone jointed with neat cement slurry mixed with pigment to match the colour of stone incl cutting and polishing and making hole in stone and RCC shelves suitable for gas pipe, with round edges where required and incl 15mm screed bed with CM1:6 including dismentling of existing granite complete all as specified and as directed.

Taking down chowkhats or frame with shutter w/o taking off shutter from the frame area not exc 1.5 Sqm each all as specified.

All as per srl item No. 21.00 here-in-before but area exc 1.5 Sqm and not exc 4 Sqm each.

Taking down shutters of any description exc 1 Sqm and not exc 2 Sqm each complete all as specified and as directed.

M&L for framed work as in doors or gates of angle or other section with gusset plates, hold fast rails, braces, etc, complete, drilled for fixing of steel sheeting or other covering. Doors, etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging, also fastening and fixing complete all as specified and as directed.

S & F pressed steel frames 125x60mm as per IS for door with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc including PCC 1:5:10, type B0 (20mm aggregate) filling in steel frame complete all as specified

All as above but 105x60mm size

S&F for 35mm thickness of factory made flush shutter solid core construction with block board core & ply wood face panels, commercial type on both side including 35 x 6 thick 2nd class Hard wood lipping on edge, complete all as specified and as directed.

S&F glazed and skelton shutters factory made 35mm thick open rebated and prepared to receive glass, gauge etc (without sash bars) edging of framing plain, chamfered or rounded with cut and mitred beads for securing glass etc. sizes of members of shutters as specified in SSR Part-I, Section 8, Clause 8.24(a) complete all as specified and as directed

S&F steel window 1.25 mm thick Box type (Primer coated) ERW hollow P section of size 60 mm x 25 mm double rebated comprises glazed and gauzed skelton shutter EWR sec 50 mm x 20 mm and 1 mm thick and two openable leaf consisting two Nos sash bar of T- section 20 mm x 3 mm complete welded to frame with one vertical mullion of EWRR box type T- section of size 60 mm x 25 mm and 1.25 mm thick including cuttings holes and making good dismantled portion in PCC (1:2:4) type B-1 four Nos for each window including following fittings welded to failed shutters:- (a) Hold fasts 150 mm long of 12 mm x 3 mm made to shape-04 nos per window. (b) Handle of Z sec 20 mm x 25 mm, 100 mm long-1 Nos of leaf (c) MS tower bolt 150 mm long 02 Nos per leaf. (d) Z sec 20 mm x 25 mm , 100 long of hollow square 15 mm x 20 mm x 63 mm welded to hinges – 01 Nos per leaf (f) MS pintal hinges of size 75mm x 12 mm -02 Nos per lear (g) Fabrication and fixing arrangement as per drawing No CEJZ/TD -06/07. Note:- Glass, wire mesh and painting shall be measured and paid separately under appropriate items.

Ditto as per description of item no above but in ventilators

S & F for powder coated aluminium frame for doors, windows ventilators with one or more rebates including joining cleat for fixing etc. including dismantling existing frame complete all as specified.

M&L Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, sliding windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings including dismantling of existing doors/window/ventilator and the directions of Engineer-in-charge

S & F framed work such as grills, gratings, etc .with ends of bars shouldered and/ or riveted , or forget into spikes ; framed guard bars barallel iron doors and similar work conforming to Fe.290.Gde-E-165

M&L for 3.00 mm thick glass sheet, ordinary quality and glazing with oil putty in square n. exc 0.5 sq. m in each pane.

M&L for 3.00 mm thick figured glass, pin head type and glazing with oil putty in squares not exc. 0.5 sqm in each pane

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. Tubes for top & bottom rails M.S. frame shall be covered with heat moulded plain colour PVC `C' channel having a PVC sheet strip of 20mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, fixing in the frame at the site as per specification & drawing

S&F PVC solid door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supplying and fixing in opening as per specification and drawing

S&F in repair floor door stopper 140mm of aluminium alloy body and tongue anodized with hard drawn steel spring fixed in floor all as specified and as directed by Engineer-in-Charge

S&F galvanized mild steel wire cloth 0.56 mm nominal dia and average width of aperture 1.18 mm and fixed with tinned tacks complete all as specified and as directed.

S&F in repair galvanized mild steel wire cloth 0.56 mm nominal dia and average width of aperture 1.18 mm and fixed with tinned tacks complete all as specified and as directed.

S&F 250mm long CP mild steel sliding door bolts stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate complete all as specified.

S&F 100mm size butt hinges medium weight cold rolled mild steel all as specified

S&F100mm size stainless steel butt hinges for fixing to PVC doors all as specified.

S&F 200mm long mild steel tower bolt stove enamelled black with bright bolt all as specified.

S&F 150 mm mild steel pressed handles oval type, stove enamelled black all as specified.

S&F aluminium anodised tower bolts 200 mm size fixed with machine screws complete all as specified and as directed.

S&F aluminium anodised Bow Handles 150 mm size fixed with machine screws.

M&L for preparation of new wood surface of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified

M&L preparation of new or previously untreated steel surfaces of any description, n. exc. 10cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer all as specified and as directed.

S&F in repair fancy CP Bib Cock long nose (Foam Flow) with Flange Make Prayag Cat No PIS-09H or equivalent of makes of Group I of Appx “B” suitable for fixing to 15mm bore (dia) GI Pipe, complete as all specified and as directed.

S&F in repair fancy CP 2 way Bib Cock with Flange of Make Prayag Cat No PIS-12H or equivalent makes of Group I of Appx “B” suitable for fixing to 15mm bore (dia) GI Pipe, complete as all specified and as directed.

S&F in repair fancy CP center hole basin mixer w/o pop up (9" spout) of Make Prayag Cat No 9350-N or equivalent of Group I of Appx “B” suitable for fixing to 15mm bore (dia) GI Pipe, complete as all specified and as directed.

S&F in repair fancy CP pillar cock chromium plated of make Prayag CAT No 9402 or equivalent makes of Group I of Appx “B” suitable for fixing to 15mm bore (dia) GI Pipe, complete as all specified and as directed.

S&F in repair fancy CP Concealed Stop Cock with Adjustable Wall Flange make Prayag CAT No 9818 or equivalent of makes of Group I of Appx “B” suitable for fixing to 15mm bore (dia) GI Pipe, complete as all specified and as directed.

S&F in repair fancy CP angular stop Cock with Wall Flange of make Prayag CAT No 9810 or equivalent makes of Group I of Appx “B” suitable for fixing to 15mm bore (dia) GI Pipe, complete as all specified and as directed.

S&F in repair fancy CP 2 way angular stop Cock with Wall Flange Make Prayag Cat No 9911 or equivalent makes of Group I of Appx “B” suitable for fixing to 15mm bore (dia) GI Pipe, complete as all specified and as directed.

S&F in repair fancy Wall Mixer 3-in-1 with provision for both Over Head Shower and Hand Shower complete with 115mm long bend Pipe, connecting legs & wall flange of makes of Make Prayag Cat No 9880 or equivalent makes Group I of Appx “B” suitable for fixing to 15mm bore (dia) GI Pipe, complete as all specified and as directed.

S&F in repair fancy CP Sink mixer swinging spout (Wall mounted) with connecting legs & wall flanges of Make Prayag Cat No 9855 or equivalent makes of Group I of Appx “B” suitable for fixing to 15mm bore (dia) GI Pipe, complete as all specified and as directed

S&F in repair fancy Over Head Shower square wall shower (Adjustable) of size (9”x9”) including all fittings of Make Prayag Cat No BOS-33 or equivalent makes of Group I of Appx “B” suitable for fixing to 15mm bore (dia) GI Pipe, complete as all specified and as directed

S&F in repair fancy Hand Shower with 1.50 Mtr flexible tube and hook of Make Prayag Cat No BHS-91S or equivalent makes of Group I of Appx “B” suitable for fixing to 15mm bore (dia) GI Pipe, complete as all specified and as directed.

S&F in repair fancy towel rail of Make Prayag Cat No BA-80 or equivalent makes of Group I of Appx “B” fixing with Chromium plated Brass Screws and Wooden/Plastic Cleats, complete as all specified and as directed.

S & F in repair health faucet 1.00mtr long flexible tube & wall hook of Make Prayag Cat No BEA-41 or equivalent makes of Group I of Appx “B” suitable for 15mm dia for iron pipe or for brass ferrule all as specified & directed.

S & F in repair Jet spray with holder for EWC 1.5mtr long of Make Prayag Cat No BEA-17 or equivalent makes of Group I of Appx “B” suitable for 15mm dia for iron pipe or for brass ferrule all as specified & directed.

S & F in repair PVC connection, heavy duty 15 mm bore, 45 cm long with 2 Nos PTMT nuts of approved quality complete all as specified and as directed.

S & F in repair new flxible PVC waste pipe of approved quality 32 mm bore, 75 cm long with one end socketed fixed to waste coupling including one PVC reducer 32mm complete all as specified and as directed

S&F in repair, Coloured PVC bath Cabinet of size 450x450x90mm with Looking Mirror (as approved) fixing with Chromium plated Brass Screws and Wooden/Plastic Cleats, complete as all specified and as directed.

S&F in repair, Sheet Glass Shelf Assembly, consisting of 5.5mm thick Sheet Glass Shelf 12 Cm Wide with Chromium plated Bracket Guard and Railing 60 Cm long, complete all as specified and as directed.

S&F in repair, Sheet Glass Corner Shelves Assembly (Transparent), consisting of 5.5mm thick Sheet Glass (size 9 x 9 inch) Shelf with Chromium plated Bracket Guard and Railing, complete all as specified and as directed.

S&F in repair fancy chromium plated soap dish, complete all as specified and as directed. Make : Prayag or equilvant

S&F Vitreous China White Wash Down Water Closet Pan (EWC) with Trap and Fixing Bolts (excluding Flushing Cistern and Flush Pipe) including connection to drain (or outgoing pipe) and to Flushing Pipe, Anti-syphonage Pipe, etc. and Making Good to Floor /distrubed surfaces including dismantling the existing unserviceable Water Closet complete all as specified and as directed.

S&F coloured vitreous china wash down one piece water closet with seat cover , hinges, Accessories set, size 625x350x730mm fitting with twin flush fitting with inlet ball valve float and handle, incl fixing bolt, with bottom and cover and mild steel chromimum plated hinging device with complete fixed in repairs all as specified and as directed by Engr-in-Charge.

S&F Vitreous China White Squatting Pan, ‘ORISSA’ Pattern of size 580x440 mm with Integral Foot Rests, ‘P’ or ‘S’ Trap, providing Joints between Flush Pipe and Socket of WC Pan incluiding provision of Lime Concrete Bedding and Making Good to Floor/distrubed surfaces and fixed-in-repairs, complete all as specified and as directed.

S&F in repair, White Plastic Water Closet Seat and Cover for Water Closet Pan (Pedestal Pattern), Closed Pattern with Flat bottom and Cover and Mild Steel Chromium plated or Aluminised Hinging Device, complete all as specified and as directed.

S&F PVC Flushing Cistern 10 Litre capacity White, Low Level, Valve less, syphonic action type with Inlet, Ball Valve, Float and handle, a pair of Cast Iron Brackets Erecting Stand duly painted including cutting and pinning in Ends, Making Good Disturbed Surfaces in Cement Mortar 1:3 including dismantling the existing unserviceable Cistern complete all as specified and as directed.

S&F Vitreous China Wash Hand Basin of size 550x400mm (Flat Back or Angle Back type) with pedestal including 32mm bore (dia) Brass Chromium plated Waste Fitting, a pair of Cast Iron Bracket duly painted / Erecting Stand including cutting and pinning in Ends Making Good disturbed Surfaces in Cement Mortar 1:3 including dismantling the existing unserviceable Wash Basin complete all as specified and as directed.

S&F in repair, Stainless Steel Sink with Drainage Board 1.0mm thick Over-all size 915x460mm and Bowl size 410x330x160mm for Kitchen or Laboratory with Plugs, Washers, Waste Fitting 32mm bore (dia) of Brass Chromium Plated, a Pair of Cast Iron Brackets duly Painted/ Erecting Stand including cutting and pinning in Ends, making good disturbed Surfaces in Cement Mortar 1:3, complete all as specified and as directed.

S&F in repair sink made of stainless steel 1mm thick, kitchen or laboratory, with plugs, washers and wastes coupling, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm (minimum), complete all as specified and as directed.

S&F in repair, Stainless Steel Kitchen Rack of size 750x800x200mm (Thickness of Sheet not less than 0.63mm) with Mild Steel Brackets and fixed to Wooden Plugs with Chromium Plated Brass Screws and Cup Washers, complete all as specified and as directed.

S&F chromium plated grating 125 mm dia circular of approved make and fixing with cement mortar 1:3 on Nahani trap or floor trap complete all as specified and as directed.

S&F in repairs 32mm dia PVC waste coupling for WHB or Sink (half or full threaded) complete all as specified and as directed

M&L for chromium plated peg set of 5 (PTMT), fixed with screws and plugging to rear side of door shutter in bath, complete all as specified and as directed.

M&L dis-connecting existing PVC tank of any capacity, setting aside (or lowering, if required) for repairs, cleaning and removing all scale and dirt, etc from tanks and from mouths of circulating pipes etc and finally washing the internal surfaces with bleaching powder/soap solution etc, re-connecting and re-fixing in position including making connections and writing Cleaned on ____ (Date) and 'Next Date of Cleaning ____ (Date), 4" height on outer face of tank with white paint complete all as specified and as directed.

Demolition of RCC water tank of any description and remove the debries from the roof and dispoed it out of defance land, complete all as specified and as directed.

S & F rotational moulded synthetic (HDPE), UV Coating, water storage tank 500 litre capacity (cylinderical vertical with closed top,) hoisted & fixed in position all as specified in SSR Part-I, including dismantling of existing water tank, complete all as spfd & directed.

S & F rotational moulded synthetic (HDPE), UV Coating, water storage tank 1000 litre capacity (cylinderical vertical with closed top,) hoisted & fixed in position all as specified in SSR Part-I, including dismantling of existing water tank, complete all as spfd & directed.

S&F 20mm Ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 15mm-142gms/ 20 mm - 210 gms./ 25mm-455gms/ 40mm - 690 gms) complete all as specified.

S&F in repair 20mm Ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 15mm-142gms/ 20 mm - 210 gms./ 25mm-455gms/ 40mm - 690 gms) complete all as specified.

S&F in repair 15mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed, complete all as specified and as directed.

S&F in repair 20mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed, complete all as specified and as directed.

S&F mild steel 300mm ordinary rat tail rod pattern springs including roller and roller plate welded to steel frame/ screwed to wooden frame complete all as specified and as directed.

M&L Galvanised iron water tubing 15 mm bore, medium grade with & including all fittings fixed to wall, ceilings and or laid in floors etc including taking down the existing tubing complete all as specified

All as per srl item No. 92.00 here-in-before but for 20mm bore tube

M&L for mild steel pipe 25 mm dia curtain rod with PVC coating fixed in the MS hooks, and finials/side brackets (both side), shade fixed in repair all as specified.

S & F in repairs 20mm dia curtain rails, mild steel , chromium plated fixing in cup board with brackets, stops, rollers etc, all as specified

M&L for PVC (SWR) floor trap with grating including jointing to waste pipe fixed with solvent cement (diameter of outlet in 75mm) including taking out damaged floor trap in any type and position complete all as specified and as directed

Cleaning of floor trap and applying of cement around the floor trap with sealant compound for arresting the seepage at any circumstances (Kitchen, Bathroom and Toilet) all as specified and as directed by Engineer-in-Charge. Make:- WACKER SILICONES (GP Silicone Sealant )

S&F PVC (SWR) pipes 110 mm dia with single socketed in any length with rubber ring joints fixed on brick walls or laid in trenches with PCC 1:4:8 complete houching with bedding including demolition and braking up existing pipes with fittings complete all as specified and as directed.

All as per srl item No. 98.00 here-in-before but 75 mm dia

S&F PVC (SWR) bends 110 mm with access door complete all as specified and as directed.

All as per srl item No. 100.00 here-in-before but 75 mm with access door

S&F for 110mm PVC (SWR) vent cowl complete all as specified and as directed.

Demolition of brick work as in walls/parapet wall,s removing grass fungus weed, roots of trees completely, grown on roof/wall surfaces, complete all as specified and as directed.

M&L for brick work with sub class 'B' old size bricks straight or curved on plan exc 6 M mean radius built in CM (1:6) all as specified.

All as per srl item No. 104.00 here-in-before but except bricks

Demolition of brick tiles single layer as in roof covering complete all as specified

Demolition of mud in roofs any thickness including plastering and leeping (whether full thickness removed or only a part thereof) all as specified

M&L for PCC (1:2:4) type B-0 (using 12.5mm graded stone aggregate) as in benching, roof padding, roof kerbs or mud stops, coping etc rounded or chamfered on edges complete all as specified and as directed

M&L for 10mm thick cement plaster in cement mortar (1:3) mixed with integral water proofing compound in the proportion recommended by manufacturer, on concrete roof surfaces finished even and fair, including cleaning the roof top by scraping down with water etc all as specified and as directed by Engineer-in-Charge (WPC shall be measured and paid separately under appropriate item of this BOQ).

Cleaning the surface and made free of dirt, foreign particle, laitance followed by grinding all all protrusion to make surface modulated. Thereafter, inspection for cracks on the surface caused by thermal expiation contraction. Cutting the grooves with suitable cutter machine in V-groove filled with repairs mortar/ microconcrate/ general purpose grout as recommended proportionally as per recommendation of manufacture. Making of Gollas at all the corners with polymer modified mortar (1:4) cement sand with 3.5% acylic of cement weight complete all as specified and as directed.

Supply and applying high build elastomeric waterproofing coating based on pure hydrophobic polyurethane cold applied of spray/brush applied, membrane with an elongation of 280% and tensile strength of 2.7N/mm2 as per ASTM D 2370, crack bridging ability of 3mm, no leakage upto 5 bars of water pressure as per DIN 1048, min 88% solid content. The system includes final base preparation, epoxy primer 1:1 (Resin; harder) application with 100% water dilution and Pure polyurethane application in 2 coats with a total min consumption of 1.25 kg per Sqm. Application should be done with Graco sprayer by a company authorised applicator” complete all as specified and as directed

M&L for Brushing neat cement slurry with 3 kg of cement per sq. meter

M & L for Bitumen Primer shall be applied on plastered surface of roofs at the rate of 0.40 Kg/Sqm of Surface area of roof for use in water proofing and dump proofing treatment

M&L Painting the roof surface with a coat of hot blown paving industrial bitumen 85/25 as a bonding material in two coats one on primed surface & 2nd on APP based polymeric membrane at the rate of 1.20 kg/sqm all as specified.

M&L for APP based polymeric membrane minimum weighing 3 Kg/sqm and minimum 3mm thick rainforced with five layer polyster non wove fabric ( wt. Not less than 150 gms/sqm) laid on primed surface by forced application complete all as specified

M&L for 40 mm thick brick tiles with 15 mm thick bedded layer of 1:3 CM laid on 2nd bitumen coated surface and joints grouted flush mortar 1:3 mixed with 5% of crude oil by weight of cement, complete all as specified .

All as per Item No 116.00 but except brick tiles

M&L Cutting out cracks to V-section in existing RCC roof slabs or terracing , cleaning out & filling solidly with a hot mixture of bitumen and clean dry sand 1:1 ( by weight) all as specified

M&L for flush pointing in cement mortar 1:3 on brick tiles laid flat including racking out joints/ pointing, hacking for key, scrubbing down with water complete all as specified

M&L for repairing of R.C.C projections, chajjias, roofs, facia and ceiling etc by necessary preparation. Scarping, cutting, chiselling derusting and cleaning exposed reinforcement, surfaces of damaged, loose R.C.C surfaces with cement concrete (1:1.5:3) using 12.5mm graded crushed stone aggregates and reinforcement with welded mesh of weight exc 2 kg per sqm but n.exc 3kg/sqm (if reqd) with or without facia and finished with cement and sand mortar (1:3) using coarse sand necessary form work and applying two coats of finishes to match with the existing surfaces in at any height complete all as specified and as directed by Engineer-in-Charge

M &L for Water proofing treatment to sunken floors of kitchen, toilets, laboratories, bath and WCs etc shall be as under:- (i) Application of Two component acrylic modified cementitious coating (aa) The surfaces to be applied shall be completely dry and free from containments such as dirt, dust, oil, surface treatments and old coatings. Concrete substrates must be mechanically prepared using abrasive blast cleaning or milling to remove cement laitance, existing coating and achieve a gripping profile that is clean, dry and free from laitance and dry other form of surface contamination. The installation instructions in manufacture's published literature should be strictly complied with, including but not limited to the following:- (bb) Chipping out any visible cracks in "V-Groove" pattern as applicable. Special attention on this part. Cleaning of cracks & then filling those cracks with SIKA latex SBR 100 putty/Dr Fixit 302 SBR latex/ Perma latex SBR/FOSROC Nitabond SBR latex/Asian paint latex as required. Final cleaning of surface with power grinder, wire brush, hair brush & vacuum pressure if required. (cc) Dampen all surfaces immediately ahed of application of Acrylic modified Cementitious coating of sika Top Seal-107/Brush Bond FOSROC/Dr Fixit/STP/CICO. (dd) Whilst the surface is still damp from saturation (S.S.D), apply one coat of Acrylic modified cementitious coating of SIKA Top Seal-107 /Brush Bond FOSROC/Dr Fixit/STP/CICO of viscosity as per manufacturer's instructions. (ee) Apply glass fabric sheet of SIKA Fab 1/FOSROC/Dr Fixit/STP whilst the first coat is wet. (ff) Once touch dry, apply second coat of Acrylic modified cementitious coating of SIKA Top Seal -107 /Brush Bond FOSROC/Dr Fixit/STP/CICO of viscosity as per manufacturer's instructions on the entire area. (gg) Second coat shall be applied after 6-8 Hrs of application of previous coat and in the direction right angle to the previous coat. (hh) The waterproofing coating should be taken to a height minimum 300mm above the finished floor level on the vertical surfaces three sides including dismantiling of existing tiles. (jj) It is essential to cure Acrylic modified cementitious coating immediately after application (minimum 6-8hrs drying) for a minimum of 3 to 5 days to ensure full cement hydration and to minimize cracking. (kk) A protection plaster 12-15mm thick) in CM 1:3 admixed with appropriate integral water proofing compound has to be applied on the walls. Admixture: SIKA Plastocrete Plus/FOSROC/DR Fixit/STP/CICO conforming to IS 2645. Providing and applying a protection screed of 50mm thick 1:4, cement sand mortar admixed with SIKA Plastocrete over the applied water proofing coating on horizontal surfaces. Admixture: SIKA Plastocrete Plus/FOSROC/DR Fixit/STP/CICO conforming to IS 2645. (ll) All the corners and joints should be pretreated with an elastic waterproofing sealing tape with a woven bonding mesh on each surface and an elastic expansions zone in the centre of Make SIKA Seal Tape/FOSROC/Dr Fixit/STP. (mm) The membrane has to be protected in accordance with the manufacturer's recommendations until placement of concrete. The membrane to be inspected for damage just prior to concrete placement and make repairs in accordance with manufacturer's recommendations. (nn)Waterproofing treatment has to be carried out through applicators authorised by the respective manufacturer's and approved by GE. (ii) All the joints of pipes and traps within the sunken portion shall be sealed properly by epoxy sealent. (iii) All CI traps in sunken slab to be enclosed with PCC 1:1.5:3 (Min 15cm) all around. (iv) The sunken portion shall be filled with PCC 1:5:10 type E-2 (using 40mm stone aggregate) complete all as specified. (v) Providing drainage spout pipe GI pipe 40mm dia bore light grade upto outside of outer wall ( Approx 450mm to 600 mm long ) including cutting to existing wall and making good the disturbed surface complete all as specified and as directed. (vi) Providing 25mm thick cement concrete 1:2:4 type B-0 using 12.5mm graded stone aggregate as in flooring for laying floor finish all as specified. Note:-Item No 25 (iv) ,(v) &(vi) shall be measured and paid seprately.

M & L Cement concrete 1:5:10 type E-2 (using 40mm stone aggregate) as in sunken flooring complete all as specified.

S & F drainage spout pipe GI pipe 40mm dia bore light grade upto outside of outer wall (Approx 450mm to 600 mm long ) including cutting to existing wall and making good the disturbed surface complete all as specified and directed.

M & L 25mm thick cement concrete 1:2:4 type B-0 using 12.5mm graded stone aggregate as in flooring for laying floor finish all as specified.

Demolition of cement concrete in ground floors and paving n. exc 15 cm thickness (below or above the ground level) complete all as specified and directed.

Material and labour for cement concrete type D-2, 1:4:8 (40mm graded aggregate) 75mm thick as in sub base of flooring complete all as specified and directed.

Material and labour for 75mm PCC 1:3:6 type C1 using 20mm graded aggregate as in plinth protection and path finishing the surfaces even and smooth with using extra cement with joint/panel filled grade 'A' bitumen compound complete all as specified and directed.

Material and labour for chequered cement concrete tiles 30cm x 30cm x 18 to 20 mm thick set with grey cement and pigments jointed and pointed in neat coloured cement slurry in floors over and including 15 mm thick cement screed bed in cement mortar (1:6) including demolition of old tiles/concrete floor all as specified and directed

Material and labour for laying 60mm thick machine pressed precast concrete interlocking paver block and shape and size conforming to IS-15658-2006 of M-35 grade with grey cement and pigment including demolition of old paver blocks complete all as specified and directed. Note : The sample shall be got approved from the GE before build procurement and lots shall be got tested independently by the GE

As per ser No above but except tiles

Material and labour for 25mm sand cushion, filling 30mm under floors or in foundations including watering and consolidation complete all as specified and directed

Material and labour for PCC (1:2:4) type B-1 (using 20mm graded stone aggregate) as in sides of rounded or chamfered on edges of interlocking/ chequered tiles, bed block concrete complete all as specified and directed

Uprooting of trees,grass,bushes etc from brick wall/roof tiles or any surfaces of bldg including dismantling the requried brick work /rooftiles/mud concrete etc for uprooting the vegetation etc and make good the same to match existing surfaces with same material or concrete 1:2:4 type B-1 after pouring the chemical (which destroy the growth of vegetation to place where vegetation removed).The rate shall include for scaffolding or any other arrangment required during this process upto 10 mtr height complete all as specified

S & F factory Made 18mm thick 100% Solid WPC ( Wood polymer Composite ) Plain Board of required size comprising of virgin PVC resin of K Value 57-60 ( Suspension Grade ), Calcium Carbonate and natural Fibers ( Wood Powders/ rice husk/ wheat husk ) and Non toxic additives, made from Extrusion process WPC foam sheet Single Extruded ( Inner ) with density not less than 650 kg/cbm Certified Company, having good screw holding capacity ( Screw Withdrawal strength of 2000 N ( Face ) & 1100 N ( Edge ), Minimum Compressive Strength of 50 N/mm2, Modulus of elasticity 850N/mm2 and resistance of spread of flame of Class A category with Property of being Termite/ Borer Free.Water/ Moisture Proof, Fire Retardant and fixing with stainless Steel butt hinges of required size with necessary full body threaded star headed counter sunk SS Screws. All as per direction of Engineer -In-Charge, Material test certificate and authentication should be compulsory provided by the manufacturing company : For WC/ Bathroom/ Toilet/ Kitchen/ Balcony Doors & Cabinets.

S & F factory Made 18mm thick 100% Solid WPC ( Wood polymer Composite ) One side Laminated Board of required size comprising of virgin PVC resin of K Value 57-60 ( Suspension Grade ), Calcium Carbonate and natural fibers ( Wood Powders/ rice husk/ wheat husk ) and Non toxic additives, made from Extrusion process WPC foam sheet Single Extruded ( Inner ) with having minimum density not less than 650 kg/cbm manufactured by Certified Company, having good screw holding capacity ( Screw Withdrawal strength of 2000 N ( Face ) & 1100 N ( Edge ), Minimum Compissive of 50 N/mm2 , Modulus of elasticity 850N/mm2 and resistance of spread of flame of Class A category with Property of being Termite/ Borer Free.Water/ Moisture Proof and Fire Retardant. WPC to be Laminated with PVC foil of minimum 14 microns thick of approved design pasted on both faces of shutter and fixinng stainless Steel butt hinges of required size with necessary full body threaded star headed counter sunk SS Screws. All as per direction of Engineer -In-Charge, Material test certificate and authentication should be compulsory provided by the manufacturing company : For WC/ Bathroom/ Toilet/ Kitchen/ Balcony Doors and Cabinets.

Supply, Fixing and installation of wall mounted Electric Kitchen Chimney of size 75 cm, compact design suction 1400m3/hr Auto clean type touch control with wave sensor duct dia 150mm including free Kit for installation with duct cover of adequate size ,kutchina and equivalent make as approved by GE.

S&F auto hinges for cabinet case (Make ; KARF/HETICH)

Supply & fix stainless steel plain basket of size 15”x18”x4” (Make: Everlite/ Slimline/Peacock/Fabshine) complete all as specified & directed.

Supply & fix stainless steel plain basket of size 15”x18”x6” (Make: Everlite/ Slimline/Peacock/Fabshine) complete all as specified & directed.

Supply & fix stainless steel plain basket of size 15”x18”x8” (Make: Everlite/ Slimline/Peacock/Fabshine) complete all as specified & directed.

Supply & fix stainless steel partition of size 17”x20”x6” (Make: Everlite/ Slim line Peacock/Fabshine complete) all as specified & directed.

Supply & fix stainless steel cutlery of size 17”x20”x6” (Make: Everlite/ Slim line Peacock/Fabshine) complete all as specified and directed.

Supply & fix stainless steel grain trolly with stand of size 21”x17”x10” (Make: Everlite/ Slimline Peacock/Fabshine) complete all as specified and directed.

Supply & fix stainless steel cup & soucer, trolly of size 15”x18”x4” (Make: Everlite/ Slim line Peacock/Fabshine) complete all as specified and directed.

Supply & fix stainless steel Plate basket of size 24"x30" (Make: Everlite/ Slim line Peacock/Fabshine) complete all as specified and directed.

Supply & fix 20” long telescopic slider to facilitate drawer slide on steel ball bearing fixed with steel screws complete all as specified and directed (Make: Nixon/Radol/Ozone Ultima or Equivalent) complete all as specified and directed.

Supply & fix 150 mm size stainless steel bright finish handle for cabinet shutter.

M&L 75 mm thick plain cement concrete 1:4:8 type D-2 (using 40mm graded stone agg as in sub base finishing the surface even and rough to receive floor finishes complete all as specified and directed.

M&L for durastone non skid vitrified tile 400x400x10 to 12mm thick in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with tile laid over and including screed bed or bedding layer 15 mm thick in CM (1:6) complete all as specified and directed.

M&L PCC 1:3:6 type C-1 (using 20 mm graded stone agg) as in seismic and other similar bands, coping, bed block or similar work including necessary form work as in filling of pressed steel door frame complete all as specified and directed.

S & F Continuous (piano) hinges, mild steel, bright finish or electrogalvanised., width of flaps when open in 30mm complete all as specified and as directed.

S&F stainless steel soft close hydraulic clip on concealed hinges for full overlay (0 degree crank ) for kitchen cupboard ,complete all as specified and directed.

S & F 75mm Extruded aluminium alloy handles, fabricated type,anodised, complete all as specified and directed.

Demolition of reinforced cement concrete in ground floors and paving n.exc 15 cm thickness (reinforcement to cut as required to facilitate demolition)complete all as specified and directed

M&L pre cast RCC 1:2:4 type B1 using 20mm graded stone aggregate as in Manhole cover slab including necessary form work set in CM 1:4 complete all as specified and directed.

Material and labour for reinforced cement concrete (1:2:4) type B-1 (20 mm graded aggregate) slab supported on wall, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed

Material and labour for MS TMT bars 10 mm and over dia and cut to length, bent to shape required including cranking bending spirally for hooping for clos hooking ends and binding with and including MS wire (annealed) not less than 0.9 mm dia complete all as specified and directed

Material and labour for form work to soffits of suspended slabs such roof slabs, floor slabs, shelves, landings and similar work, not exceeding 200mm thick (horizontal or slopping) rough finished surfaces of concrete flat or shelfs etc. complete all as specified and directed.

Use and waste of formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n. exc. 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc. 10cm but n. exc. 20cm wide for rough finished surfaces of concrete complete all as specified and directed.

S&F for Providing precast cement concrete louvres and jallies, 25mm thick (measured solid), PCC 1:2:4, Type B0 (12.5mm graded aggregate) including all mouldings with frame Set in CM 1:4 including dismantiling/demoliation of existing louvers/jallies complete all as specified and directed.

M&L for welding in repairs not exceeding 2.5cm in length & thickness of metal to be welded not exceeding 6mm complete all as specified and directed.

S&F for anti-dusting rubber beading for door shutter for anti-snakes, dusting etc all as specified and directed

M&L for repair to steel rolling shutter of area not exceeding 8 Sqm and any description including repairing of ball bearing, top cover, anchoring rod, hasp and staple, gear operated system, crank handle, chain wheel and hand chain including necessary welding, gressing etc and making the shutters serviceable complete all as per existing pattern as specified.

S&F for fancy toilet paper holder of chromium plated fixed to walls CP brass screws complete all as speicified.

Dismantling asbestos cement, plain or corrugated steel sheeting any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and directed .

M&L for Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa, AZ-150 as in roof overing /cladding to wall, fixed with self tapping screws as specified complete all as specified and directed .

M&L for Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa AZ-150 as in roof covering/cladding to wall, fixed with self tapping screws as specified

M&L for broken glass pieces embeded in PCC 1:3:6 (75 mm thick) on boundary walls including demoliation of old glass pieces complete all as specified and directed by Engr-in-charge.

SANMATI UDYOG (BID ID -3077584)

NATIONAL BUILDERS (BID ID -3084239)