GE/863/EWS-T-15 OF 2024-25

Amount

Demolition of cement concrete (un-reinforced) in ground floors and pavings n. exc 15 cm thickness (below or above ground level) complete all as specified and directed.

Demolition of cement concrete (reinforced) of any description and in any position not otherwise specifically provided for, complete all as specified and directed.

Demolition of brickwork or stone/boulder masonry, built in cement mortar including all quions, arches, pillars, etc but excluding ashlar facings, dressed stonework and precast concrete articles, complete all as specified and directed.

Demolition of brickwork or stone measonry for ashlar facings, dressed stonework, precast concrete articles and precast concrete block walling built in cement mortar, complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing rubbish off the premises, complete all as specified and directed.

M & L for providing cement concrete Type C-1 (1:3:6) using 20mm graded stone aggregate as in coping complete all as specified and directed.

Dismantling plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings, complete all as specified and directed.

S&F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and directed.

S&F pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and directed.

M&L for stone walling of squared rubble, uncoursed, well bonded, bedded and solidly hearted, built in CM 1:6 complete all as specified and as directed.

M&L for block masonry with solid pre-cast cement concrete blocks exc 10 cm in width made out of Cement concrete type C-1 (1:3:6), using 20 mm graded stone aggregate and setting in cement mortar 1 : 6, complete all as specified and directed.

Taking down wall panelling and similar work incl frame complete all as specified and as directed.

M&L 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification complete all as specified and directed.

M&L Solid PVC Wall Lining consisting of 5mm thick single side prelam PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications complete all as per specified and directed.

S&F powder coated (Thickness of powder coating not less than 50 micron) aluminium door shutters, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc complete all as specified and directed.

S&F powder coated (Thickness of powder coating not less than 50 micron) aluminium window and ventilator shutters, side hung type/sliding without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21, 100mm long (2 No.) suitable handle (1 no.) complete all as specified and directed.

S&F powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, complete all as specified and directed.

S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDMrubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete all as specified and directed.

S&F aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples complete all as specified and directed

M&L for 5mm thick wood grain printed PVC sheet inclusive of solvent cement and fixing at site on PVC/aluminium frame as per specifications complete all as per specified and directed.

S&F mortice brass lock vertical type size 100mm with 4 levers complete all as specified and as directed.

S&F double action floor spring hydraulically regulated made up of min 1.25mm thick aluminum alloy sheet foundation box, main body with stainless steel cover governing pivot made of brass other parts made of mild steel heavy duty ISI Marked fixed in position, complete all as specified and as directed.

S&F Aluminium (die cast ) body door closer hydraulically regulated designation No 3 universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 Kg complete all as specified and as directed.

M&L for pre laminated exterior grade 9mm thick both side laminated board complete all as specified & as directed.

M&L for Forming jambs etc., built in cement mortor 1:6 to openings incl cutting toothing and properly bonding into to old work also facing ,jointing and pointing to match to existing work complete all as specified and directed.

M&L for providing reinforced cement concrete 1:2:4 type B1 (20 mm graded stone aggregate) as beams, cantilevers, bressummers , lintel over 1.5 mtr span complete all as specified and directed. (Note :- Reinforcement shall be measured and paid separately under respective item)

M&L for Use & waste form work rough finished surfaces of concrete to sides and soffits of beams, lintel and similar items, complete all as specified and directed.

Demolition of Concrete (un-reinforced) of any description and in any position not otherwise specifically provided complete all as specified and directed.

S&F Ceramic oval type Counter wash basin dimensions 560 x 470 x 190 mm vitreous china (Snow white/Ivory) including CP waste fittings, 32mm bore size, waste pipe PVC 32mm bore, complete all as specified and directed.

Taking down cement plaster, any description on brick or stone walls, etc including racking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L for external rendering 15mm thick in cement mortar (1:4) on any face of brick wall or concrete surfaces, finished fair and even, complete all as specified and directed.

M&L for rendering 15mm thick in cement mortar (1:4) on stone masonry surfaces or surface other than fair face of brick-work or on one side of lathing, finished fair and even, complete all as specified and directed.

M&L for rendering 10mm thick in cement mortar (1:6) on any face of brick walls or concrete surfaces, finished even and smooth without using extra cement, complete all as specified and directed.

M & L for rendering 10 mm thick on stone masonry surfaces or surface other than fair face of brick-work in cement plaster 1:6 and finished even and smooth (without using extra cement), complete all as specified and directed.

M&L for preparation of newly plastered surface of walls and applying two coat of cement base paint over a coat of primer complete all as specified and directed.

M&L for preparation of newly plastered surfaces of wall and applying two coat of oil bound distemper over 1 mm thick wall care putty on walls, complete all as specified and directed.

M&L for preparation of newly plastered surfaces of wall and apply two coat of distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification using paint roller technology and providing 1 mm thick wall care putty and sanding the surface to prepare the surface even and smooth, complete all as specified and directed.

M&L for complete removal of existing treatment on surfaces of walls and apply two coat of distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification using paint roller technology and providing 1 mm thick wall care putty and sanding the surface to prepare the surface even and smooth, complete all as specified and directed.

M&L for complete removal of existing treatment, washing, rubbing down and stopping of distempered and painted surfaces of walls and applying one coat of acrylic smooth exterior paint (weather coat) complete all as specified and directed.

M&L for Washing, rubbing down and stopping of old treated distempered and painted surfaces of walls and applying one coat of cement base paint, complete all as specified and directed.

Dismantling of wall and ceiling boards (fibre, pulp, insulation, etc) or insulation boards/slabs/blankets, any thickness inclduding cover fillets/frame, complete all as specified and directed.

S&F anodised aluminium snap grid of size 605 X 605 mm frame work for false ceiling including hangers 6mm dia G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of G.I. flat 40 x 3mm size 60mm long and expansion hold fasteners 12.5mm dia 40mm long complete all as specified and directed.

M&L exposed metal frame ceiling with 8mm thick calcium silicate board of siliceous and calcareous material reinforced with cellulose fibre for fixing in 600mmX600mm grid (frame work for ceiling shall be measured and paid seprately) complete all as specified and directed.

M&L for light shade Vitrified tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over and including 15mm thick cement screed bed or bedding layer in CM (1:6) complete all as specified and as directed.

M&L for light shade Vitrified tile 10mm thick polished, area of tile n exc.0.36 sqm as in Skirting set and jointed in cement slurry over and including 10mm thick rendering as in backing coat rough finished in cement mortar (1:4) and pointed in white cement with pigment to match the colour of tiles complete all as specified and directed.

M&L for Non skid ceramic coloured (colour & shade as approved) tiles of 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors set and jointed in neat cement slurry over and including 15mm thick screed in cement mortar (1:6) and pointed in white cement with pigment to match the colour of tiles complete all as specified.

M&L for glazed clolour ceramic tiles of size 350x 250x 7 mm/ 450X 350X 7mm thick as in vertical surfaces/dado laid over 10mm thick rendering (rough finished) as back coat in CM 1:4 etc. set and jointed in neat cement slurry and pointed in coloured cement with pigment complete all as specifed and as directed.

M & L for chequered cement concrete tiles 20 cm x 20 cm x 25 mm/30 cm x 30 cm x 25 mm thick, set, jointed and pointed in neat cement slurry over 20mm thick screed bed in cement mortar 1:4 as in floors with grey pigment cement and pigment, complete all as specified and directed.

M&L for 25mm thick cement concrete type B-0, 1:2:4 (using 12.5 mm graded crushed stone aggregate) complete as in levelling of floor etc complete all as specified and as directed.

M & L for providing cement concrete type C-1 1:3:6 using 20mm graded aggregate as in roof kerb or mud stops, round on edges complete all as specified and directed.

Taking down chowkats or frames not exc 1.5 sq.m each but with shutters (without taking off shutters from the frames), complete all as specified and directed.

Taking down chowkats or frames exc 1.5 sq.m but n.exc 4 sq.m each but with shutters (without taking off shutters from the frames), complete all as specified and directed.

Taking down shutters of any description exc 1 sqm and not exc 2 sqm each and removing, complete all as specified and directed.

S&F of factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made of MS tubes for top & bottom rail. MS frame shall be covered with heat moulded wood grain printed PVC sheet ‘C’ channel having a pvc sheet strip of 20mm width stuck inside with solvent cement for stiles and wood grain printed PVC sheet for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; paneling of wood grain PVC sheet to be fitted to the MS Frame/sealed to the stiles & rails with suitable PVC sheet beading, & 5mm thick x15mm wide PVC sheet beading used inside stiles and rails and decorative PVC beading of 10mm x 10mm (90) degree used and joined together with solvent cement, complete all as specified and directed.

M&L for solid PVC door frame of size 50x47mm made out of 5mm thick wood grain printed pvc sheet reinforced with MS square tube, complete all as specified and directed.

S&F 30mm thick Flush shutters, solid core construction, with particle board core and plywood face panels, both face is covered with decorative face veneer with lipping/frame to match complete all as specified and directed.

S&F 2nd class hard wood 35 mm thick Glazed and sketon shutters, open rebeated and prepared to receive glass, gauze, etc (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc, sizes of members of shutters as specified in SS Part-I, section 8, clause 8.24 (a) supplied and fited to chowkat complete all as specified and directed.

S&F Pressed steel frames made of MS sheet of profile 165 mm X 60 mm for door and window frames with one or more rebates including lock strike plate, shock absorber, 20 mm dia 60 mm long MS conduit for housing of a drop bolt, treating of internal surfaces of chowkhats with coal tar or black paint including hinges, hold fasts/lugs etc complete all as specified and directed.

M&L for Cement concrete (1:3:6), type C-1 using 20mm graded stone aggregate as in filling of steel chowkhats including necessary form work complete all as specified and directed.

M&L for preparing new or previously untreated surfaces of wood or wood based materials of any description over 10 cm width or girth and applying two coat of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

S&F steel windows/ventilaor with side hung shutters including projecting type hinges with steel handle and steel peg stay complete with glazing bars dovetailed or welded, complete all as specified and directed.

All as per item No 64 here-in-before, but without glazing bars, complete all as specified and directed.

Supply and fabrication of framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290 Gde-E-165 complete all as specified and directed.

M & L for preparation of new or previously untreated surfaces of steel of any description, over 10 cm in width or girth not otherwise described applying two coats of synthetic enamel paint (ordinary tint) over a coat of red oxide primer complete all as specified and directed.

M&L for Preparation of old steel surfaces of any description, over 10cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and directed.

M&L for laying plain cement concrete type C-1 (1:3:6) (using 20mm graded stone aggregates) as in plinth protections, 75 mm thick , finished even and smooth without using extra cement , with joints 10 mm wide and in full depth at corners and @ 3.0 metre centre to centre, filled with mastic mortar, complete all as specified and directed by Engr-in-Charge.

S&F for wire netting of stainless steel wire 1.4 mm dia fixed with tinned tacks of stainless steel wire staple and mesh size 12 mm, complete all as specified and directed.

S&F 3.00 mm thick sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane, complete all as specified and directed.

S & F 300mm length aluminium alloy, anodised, sliding door bolt hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed, complete all as specified and directed.

S & F 150mm Aluminium handles, cast type, anodised and fixed with screws, complete all as specified and directed.

S & F 125mm Aluminium handles, cast type, anodised and fixed with screws, complete all as specified and directed.

S & F 150mm aluminium, anodised, barrel tower bolts of extruded section and fixed, complete all as specified and directed.

S&F 200 mm aluminium, anodised, barrel tower bolts of extruded section and fixed, complete all as specified and directed.

S & F 100 mm butt hinges, medium weight, cold rolled mild steel and fixed, complete all as specified and directed.

S & F mild steel 300mm ordinary rat tail rod pattern springs, including roller and roller plate, complete all as specified and directed.

S & F in repair brass chromium plated tubular towel rail 20mm dia incl brackets, complete all as specified and directed.

S&F 150 mm Floor door stopper of aluminium alloy body and tongue, anodized with hard drawn steel spring complete all as specified and as directed.

S&F in repair shelf of PTMT fixed with and including chromium plated brass screws and wooden cleats (Min weight 300 gms), complete all as specified and directed.

S&F in repair soap dish any type, fixed to plugs with chromium plated brass screws complete all as specified and directed.

S&F in repair MS chromium plated peg set of five fixing with wall complete all as specified and directed.

S&F galvanised steel water tubes 15 mm bore medium grade, with all fittings and fixed complete to walls and ceiling or laid in floors including taking down corroded GI pipe complete all as specified and as directed.

S&F galvanised steel water tubes 20 mm bore medium grade, with all fittings and fixed complete to walls and ceiling or laid in floors including taking down corroded GI pipe complete all as specified and as directed.

S&F galvanised steel water tubes 25 mm bore medium grade, with all fittings and fixed complete to walls and ceiling or laid in floors including taking down corroded GI pipe complete all as specified and as directed.

S&F Vitreous china white wash down water closet (pedestal pattern) including PVC seat cover and connection to drain or out going pipe and to flushing pipe anti-syphonage pipe etc, fixed as in repair, complete all as specified and directed.

S&F PVC low level flushing cistern (white) of 10 liters capacity with inlet ball float valve, PVC flush pipe and necessary fixing arrangements and connecting to water pipe and WC etc and fixed in repairs, complete all as specified and directed.

S&F in repairs , first quality, wash basins, vitreous china, white, flat back of size 550x400mm, including brackets and cutting for and pinning in ends of brackets or erecting stand 32mm dia waste fittings, brass, chromium plated with long screwed shanks and fly nuts, 32mm dia HDPE waste pipe and including new brackets, complete all as specified and directed.

S&F Vitreous China urinals, bowl type (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement (minimum), with grating and union for discharge pipe (excluding flushing cistern, and flush pipe ) including waste pipe 32mm dia bore fixed in repairs complete all as specified and directed.

Supply only Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed complete all as spcified and directed.

S & F in repair Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect complete all as specified and directed.

S&F in repairs two way fancy type chromium plated 15 mm bore bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed, complete all as specified and directed.

S&F Self-closing tap for urinal, cast copper alloy 15mm bore, chromium plated, screwed for iron pipe and fixed complete all as specified and directed.

S&F in repairs fancy type chromium plated, 15 mm bore bib taps, cast copper alloy with crutch or butterfly handle, screwed down for iron pipe or for brass ferrule and fixed, complete all as specified and directed.

S&F in repair 15mm stop cock/angle cock cast copper alloy with crutch or butterflty handle, screwed down screwed for iron pipe or for brass ferrule fancy type chromium plated with fancy shank and cup, complete all as specified and directed.

S&F in repair PVC connections 15mm size with PTMT nuts of length 450 mm, complete all as specified and directed.

S&F in repair cast iron floor trap 100 mm dia, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified & directed.

Dismantling of cast iron or AC drain pipe/ PVC pipe jointed in cement mortar of size 110mm bore complete all as specified and directed.

Dismantling of cast iron or AC drain pipe/ PVC pipe jointed in cement mortar of size 75mm bore complete all as specified and directed.

S&F of 110mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed on wall with MS clamp, complete all as specified and as per direction of engineer in charge

S&F PVC SWR pipes single socketed in any length with rubber rings joints laid in trenches or in floors 110mm, complete all as specified and directed.

S&F PVC SWR pipes single socketd in any length with rubber rings joints laid in trenches or in floors 75 mm, complete all as specified and directed.

S&F of 75mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed on wall with MS clamp, complete all as specified and as per dierction of engineer in charge

S&F PVC (SWR) branch pieces single socketed Y equal or unequal 110mm, complete all as specified and directed.

S&F PVC (SWR) bends any radius 110mm, complete all as specified and directed.

S&F PVC (SWR) bends 75mm dia, complete all as specified and directed.

S&F PVC (SWR) junction single 110 mm, (Single T) equal or unequal, complete all as specified and directed.

S&F PVC (SWR) vent cowl 110 mm, complete all as specified and directed.

S&F 20mm bore Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and directed.

S&F 1000 litres capacity rotational moulded, triple layer polythene water storage tanks (cylindrical vertical with closed top) hoisting and fixed in position on roofs including fittings & dismantling existing water storage tank along with float valve, complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for, complete all as specified and directed.

S&F roof trusess (framed), verticle pole , trussed ,purlins, crane gantries rails and fastenings and heavy bracket framing (beam tea angle chanell or flat section ) including distance pieces,cleats etc confirming to Fe 410-W (grade -E-250) quality A complete all as specified and directed.

S&F Precast cement concrete 1:3:6, type C1 (Using 20 mm graded stone aggregate) in landings, cover slabs (for manholes etc.) shelves and similar articles with plain faces and set in cement mortar 1:4 complete all as specified & directed.

S&F mild steel TMT bars 10 mm dia., and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing wire complete all as specified & directed.

S&F mild steel TMT 6 mm to 8 mm dia, cut to length, bent to shape required, including cranking, bending spirally for stirrups, hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia, or securing with clips complete all as specified & directed.

S&F PVC bath cabinet fixed with and including chromium plated brass screws and wooden claeats size 355mmx455, complete all as specified and directed.

S&F in repairs Harrison rails, mild steel, chromium plated with fixing brackets, stops, rollers etc complete all as specified and directed.

M & L for broken stone/boulders of guage exc 63mm but n exc. 100 mm, deposited, spread and evelled in layers n exc. 15 cm thick, watered and rolled/rammed to a true surface complete all as specified and directed.

Excavation in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in hard/dense soil complete all as specified & directed by Engineer-in-charge.

Returning filling in soil including spreading, levelling, watering and well ramming in layers not exceeding 25cm thick complete all as specified & directed by Engineer-in-charge.

Removal of surplus soil to a distance n.exc 50 m and depositing where directed at level not exceeding 1.5 m above the starting point complete all as specified & directed by Engineer-in-charge.

Demolition and breaking up drain pipes (Salt glazed ware, AC or Reinforced concrete) 150mm dia set in cement mortar complete all as specified and directed.

M & L cement concrete bed to drain pipe including packing under and haunching against side of pipe after they are laid and tested in cement concrete 1:4:8 type C-2 using 40 mm graded stone aggregate for 150 mm dia pipe complete all as specified and directed.

Supply, laying, jointing and testing 150mm bore reinfirced conctete pipes class NP-2 laid and jointed in cement mortor 1:1 complete with collars or socket/spigot type laid jointed and haunching at side in cement complete all as specified and directed. (Note- cement concrete used for haunching concrete shall be measured and paid seperately)

M&L for 20 mm thick Granite (of any type and colour) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite incl all moulding etc complete all as specified & as directed .

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in hard/dense soil complete all as specified and directed.

M&L for P.C.C 1:4:8 type D-2 using 40 mm graded stone aggregate as in foundation filling, sub-base of floors and mass concrete complete all as specified and as directed.

M&L for walling of random rubble stone masonry uncourced, well bonded, bedded and solidly hearted built in CM 1:6. complete all as specified and as directed.

M&L for 40 mm thick Cement Concrete 1:2:4 (using 12.5 mm graded stone aggregate) as in damp proof course (DPC) to horizontal or vertical surfaces including necessary form work and mixing of water proofing compound as per manufacturer’s instructions complete all as specified and directed. Note: - Water proofing compound will be measured and paid separately.

Supply only water proofing compound (WPC), complete all as specified and directed.

Spreading and leveling n.exc 25cm thick each layer incl well ramming, watering and consolidation complete all as specified and directed.

M&L for Hardcore of broken stone or boulders gauge n exc. 63mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for 75 mm thick P.C.C 1:4:8 type D-2 using 40mm graded stone agg as in sub base of floor complete all as specified and as directed.

M&L for 25 mm thick PCC 1:2:4 type B1, 20 mm graded stone aggregate as in flooring including finishing cement concrete rough surface with out using extra cement. complete all as specified and directed.

M&L for non skid ceramic coloured tiles 7 to 8 mm thick (square/Rectagular) area of each tile exceeding 0.06 Sqm but not exc 0.11 Sqm in floor etc, set & jointed in neat cement slurry and pointed in white or coloured cement to match the surface over and including cement screed bed 15 mm thick in cement mortar 1:6 base complete all as specified and directed.

M&L for laying plain cement concrete type C-1 (1:3:6) (using 20mm graded stone aggregates) as in plinth protections, 50 mm thick , finished even and smooth without using extra cement , with joints 10 mm wide and in full depth at corners and @ 3.0 metre centre to centre, filled with mastic mortar, complete all as specified and directed by Engr-in-Charge.

M& L for two coat of oil bound distemper including preparation of newly plastered surfaces of wall and applying a coat chalk whiting complete all as specified and as directed.

M&L for providing reinforced cement concrete 1:2:4 type B1 ( 20 mm graded stone aggregate) as chajja , shelves etc complete all as specified and directed. (Note :- Reinforcement shall be measured and paid separately under respective item)

M&L for use & waste form work rough finished surfaces of concrete to chajja ,shelves , troughs and similar items including edges complete all as specified and as directed.

S&F Second class hard wood plain, solid, straight chowkats and frames, wrought, framed, rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed.

S&F 2nd class hard wood 35 mm thick plain, framed, panelled shutters (any no of panels) with panels of timber flat on both sides (feather edge) or of veneered partical boaed medium density, wood pertical board with commercial face veneers; supply and fix two chowkats complete all as specified and directed.

S&F 250 mm Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed.

S&F 4.8 mm thick sheet glass ordinary quality and glazing with oil putty in squares area not exceeding 0.5 Sqm in each pane, complete all as specified and directed.

S&F rolled mild steel Fe -290(Gde E-165) for Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc.complete all as specified and directed.

M& L for machine cut kota stone slab flooring OF SIZE 550MMX550MM AND 18-20mm thick laid over 20 mm thcik cement screed bed 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab, complete all as specified and directed.

M&L for sand filling under floors or foundation spreading and levelling in layer n exc 25 cm thick including well ramming including watering and consolidation complete all as specified and directed

M&L for preparation of newly plastered surfaces of wall and applying three coat of white wash on walls, complete all as specified and directed.

M/L for 20mm thick cement concrete type B-0 1:2:4 (using 12.5 mm graded crushed stone aggregate) as in levelling of floors, etc. complete all as specified and as directed.

S&F rolled Mild steel plates plain or chequrred cut or notched (ordinary and counter sunk) forming holes, without any attachment.(Fe-410-W(Gde E-250)Quality-A), complete all as specified and directed.

S&F 3.00 mm thick figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sq. m in each pane complete all as specified and directed.

S & F brass chromium plated tubular towel rail 20mm dia and bracket complete all as specified and directed.

S&F shelf of PTMT fixed with and including chromium plated brass screws and wooden cleats (Min weight 300 gms), complete all as specified and directed.

S&F soap dish any type, fixed to plugs with chromium plated brass screws complete all as specified and directed.

S&F MS chromium plated peg set of five fixing with wall complete all as specified and directed.

S&F Galvanised iron steel water tubing, 15mm bore, medium grade with all fittings and fixed to walls and ceilings or laid in floors complete all as specified and directed.

S&F Galvanised iron steel water tubing, 20mm bore, medium grade with all fittings and fixed to walls and ceilings or laid in floors complete all as specified and directed.

S & F 500 ltr capcity rotational moulded polyethylne water storage tanks, tripple layered, (cylindrical vertical with closed top) duly provided with necessay fittings/fixtures for connecting inlet, outlet, washout and overflow pipes, hoisted incl ball brass valve, high pressure with polythene float and flynut complete screwed for iron pipe or brass ferrule 20 mm bore and fixed in position complete all as specified and directed.

S&F Vitreous china wash down water closet pan (pedestal pattern), white, including flush pipe of polyethylene of low or high density or PVC 32 mm dia., plastic water closet seat closed pattern with cover and hinging device and trap with connection including CP jet with steel pipe complete all as specified and directed by Engr-in-charge.

S&F 10 ltr capacity PVC valve less symphonic action type flushing cistern, white ,with inlet ball valve, float and handle including bracket and 32 mm dia HDPE flush pipe and connected to squat pattern /pedestal pattern water closet (Flush shall be fixed at suitable height for smooth functioning ) complete all specified and directed.

Supply & fixing vitreous china wash basin, white, flat back of size 550mm x 400mm including 32mm dia PVC flush pipe with coupling and set of brackets including 15mm bore pillar tap fancy type cast copper alloy with capstan head, chromium plated, screwed down, high pressure with or without lettered 'Hot' or 'Cold' with long shank and fly nuts screwed for iron pipe or for brass ferrule incl PVC connections 15mm size with PTMT nuts of legth 450mm complete all as specified and directed by Engineer-in-Charge.

S & F in 15mm bore bib tap Chromium Plated fancy type cast copper alloy with crutch or butterfly hadle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and as directed.

S & F gun-metal, globe or gate valves, with iron wheel head, screwed both end for iron pipe and fixed to 20 mm bore GI Pipe complette all as specified and as directed.

S & F 15mm bore stop valve/angle valve cast copper alloy chromium plated fancy type screwed down, high pressure, with crutch or butter fly handles complete all as specified & directed.

S&F 75 mm bore PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed.

S&F 125/110 mm PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and directed.

S&F PVC connections 15 mm size with PTMT nuts of length 450 mm complete all as specified and directed.

M&L 60mm thick Coloured interlocking (M-35) cement concrete tiles with grey cement and pigment of approved design & pattern as approved by Engineer-in-Cahrge including 50 mm thick sand cushioning Complete all as speciifed and directed.

M&L for cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished, and reforming benching as required, complete all as specified and directed.

M&L for PCC 1:3:6 type C-2 using 40 mm graded aggregate as in surface channel and drain complete all as specified and directed.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc., complete all as specified and directed.

M & L for point wiring using approved colour coding as per IS by using FRLS PVC insulated 1.5 Sqmm multistranded,1100 volt grade copper conductor cable unsheathed type, alongwith 1.5 Sqmm FRLS PVC insulated stranded copper conductor cable for continous earthing in & incl PVC casing & caping with accessories having ISI mark fixed on wall surfaces / ceiling including provision of suitable gang box for fixing switches, sockets, regularors, etc. for one light/fan/bell point controlled by one switch complete all as specified and directed by Engr-in-charge.

All as per item No 174 here-in-before but for one multipin socket outlet 5 Amp on the independent board, complete all as specified and directed by Engr-in-charge.

All as per item No 174 here-in-before but for one multipin socket outlet 5 Amp on the same board with other switches, complete all as specified and directed by Engr-in-charge.

All as per item No 174 here-in-before but for one multipin socket outlet 15 Amp, independent board using 2.5 sqmm copper conductor, complete all as specified and directed by Engr-in-charge.

S & F switch piano type 5 Amp, 230 Volt, flush type single pole one way complete all as specified and directed.

S & F socket outlet multipin 5 Amp 230 Volt flush type complete all as specified and directed.

S & F switch piano type 15 Amp, 230 Volt, flush type single pole one way complete all as specified and directed.

S & F socket outlet multi pin 15 Amp 230 Volt flush type complete all as specified and directed.

S & F Ceiling rose, 3 terminal, PVC isolated body complete all as specified and directed

S & F LED light fitting 20W, 220 volt AC, having colour temperature daylight (6500K), Decorative ultra slim square profile LED lighting fixture with extruded polycarbonate, connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

S & F LED light fitting 1x10W/1X12W bulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size, complete all as specified and directed by Engr-in-charge.

S & F sheet metal enclosure double door distribution board single pole and neutral, 4 way 240 volt with 200 amps rated bus bar complete with bus and neutral link complete all as specified and directed.

S & F MCB 6 to 32 amp rating 240V, 10KA 'C' curve, Single pole in the MCB DB complete with connection testing and commissioning complete all as specified and directed.

All as per item No 186 here-in-before but of SPN and capacity 32 Amps, complete all as specified and directed by Engr-in-charge.

Supply, laying & testing LT UG XLPE insulated armoured heavy duty electric cable with aluminium conductor 1100 Volts grade cross-sectional area 6 sqmm 2 core as per IS specification laid through GI pipe/on floor/wall complete all as specified and directed

Supply and laying of GI pipe light galvanized iron with all fitting laid in trenches for cable proctection of 50 mm bore complete all as specified and directed.

Supply and fixing lamp holder, PVC/ Polycarbonate type with back plate suitable of batten fittings.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete.

Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300mm sweep with, blades, and frame and louvers

M & L of earthing complete with galvanized steel earth plate electrode 60cmx60cmx6.0mm thick, buried directly in ground (earth pit not less than 2.25metres deep below normal ground level) with top edge of the plate not less than 1.5meter below normal ground level ,connected to and including using galvanized iron strip of 25.0 x 4.0 mm thick as earthling lead by means of bolts nuts, cheek nuts and washers of galvanized iron or steel .earth plate surrounded by alternate layers packed with char coal dust and common salt ,15cm thick and 15cm wide all around bottom and top and watering pipe 20mm bore of GI light grade with funnel, wire mesh and 40mm dia GI protection pipe medium grade all as shown in electrical plate no-3 of SSR part-I and connected to earthling test point, and including testing on completion all as specified location and as directed by Engineer-in -charge. Note: 1. Suitable quantity of charcoal, common salt, funnel, GI pipe required for watering, pit & CI pit cover etc is deemed to be included in quoted rate and lead wire used beyond 7.5m from pit cover will be measured separately. 2.On testing after completion if the desired resistance is not obtained the earthing shall be re-done at no extra cost.

Cutting existing steel tubing for alterations or additions (Each cut measured) incl Screwing of existing steel tubing in position for alterations or additions without taking down for tapping 25mm dia from the existing pipe line (any size) complete all as specified and as directed by Engineer-in-Charge.

S & F stepped type electronic fan regulator flush type, complete all as specified and directed.

S & F LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC, having colour temperature daylight (6500K), Ultra modern recess mounting luminaire with high performance LEDs, suitable for mounting with Armstrong/Grid ceiling including connecting up three core flexible copper conductor cable of suitable size complete all as specified and directed

S & F in replacement of sheet metal enclosure double door distribution board single pole and neutral, 8 way 240 volt with 200 amps rated bus bar complete with bus and neutral link complete all as specified and directed.

S & F in replacement MCB 6 to 32 amp rating 240V, 10KA 'C' curve, Single pole in the MCB DB complete with connection testing and commissioning complete all as specified and directed.

All as per item No 198 here-in-before but of SPN and capacity 40 Amps, complete all as specified and directed.

Supply & laying LT UG XLPE insulated armoured heavy duty electric cable with aluminium conductor 1100 Volts grade cross-sectional area 10 sqmm 2 core as per IS specification laid through GI pipe/on floor/wall complete all as specified and directed

M&L for dismantling of service wire 10 sqmm 2 core with all accessories incl GI pipe, service bracket, etc., complete all as specified and directed.

S&F 9 watt Cool day white LED B22 base , AC, 240Volt, complete all as specified and directed.

M & L in replacement of earthing complete with galvanized steel earth plate electrode 60cmx60cmx6.0mm thick, buried directly in ground (earth pit not less than 2.25metres deep below normal ground level) with top edge of the plate not less than 1.5meter below normal ground level ,connected to and including using galvanized iron wire of 4.0 mm thick as earthling lead by means of bolts nuts, cheek nuts and washers of galvanized iron or steel .earth plate surrounded by alternate layers packed with char coal dust and common salt ,15cm thick and 15cm wide all around bottom and top and watering pipe 20mm bore of GI light grade with funnel, wire mesh and 40mm dia GI protection pipe medium grade all as shown in electrical plate no-3 of SSR part-I and connected to earthling test point, and including testing on completion all as specified location and as directed by Engineer-in -charge. Note: 1. Suitable quantity of charcoal, common salt, funnel, GI pipe required for watering, pit & CI pit cover etc is deemed to be included in quoted rate and lead wire used beyond 7.5m from pit cover will be measured separately. 2.On testing after completion if the desired resistance is not obtained the earthing shall be re-done at no extra cost.

Schedule of Credit

Kusan Enterprises (BID ID -3071169)

chankaya solutions (BID ID -3071437)

M/S Shamsher Negi Dewa (BID ID -3069969)

R B TRADERS (BID ID -3070596)

M/S Gopal Singh (BID ID -3071508)

M/S Gulab Singh (BID ID -3072442)

M/S PAWAN KUMAR NEGI GOVT. CONTRACTOR (BID ID -3071269)