ADDITION/ALTERATION OF ENTRY GATE MT PARK OF 189 MH, PROVN OF TILE WORK, SANITARY FITTINGS, DOORS EXHAUST FANS IN WASHROOM OF OTM ACCN, PROVISION OF CERTAIN B/R WORKS IN COMMUNITY PARK IN BRIGADIER ENCLAVE AND SPECIAL REPAIR TO BLDG NO A/10/70

Amount

Demolition of cement concrete (un reinforced) in ground floors and paving n.exc 15cm thickness (below or above ground (level) and lowering if necessary, including removal of the rubbish off the premises complete all as specified and directed.

Demolition of RCC of any description and in any position not otherwise specifically provided for including (renforcement cut as per required to facilitate demolition) including removal of the rubbish off the premises complete all as specified and directed.

Dismantling of Stone slabs and tiles of any description or thickness in floors, aprons etc complete all as specified and as directed including removal of the rubbish off the premises complete all as specified and directed.

Demolition of Brickwork masonry, laid in Cement mortar including removal of the rubbish off the premises all as specified and directed.

Dismantling of floor hearth or wall tiling including cement mortar bedding but not backing and removing serviceable tiles to store yard and rubbish off the primises as directed

Dismantling wrought iron or mild steel work of any description not otherwise provided complete all as specified and as directed.

Dismantaling of plain or corrugated steel sheeting, any gauge, thickness, including nainital or similar pattern roof coverings complete all as specified and directed.

Taking down cement plaster of any description from brick wall surfaces etc including racking out joints and hacking for key, scrubbing down with water etc complete including removal of the rubbish off the premises all as specified and directed.

Taking down of chowkats or frames not exc 1.5sqm each with shutters (without taking off shutters from frames ) complete all as spd and directed.

Taking up or down steel water tubings and fittings etc complete and making good disturbed surfaces of walls/ceilings etc for 15 mm bore pipe complete including stacking aside for reuse and removal of unserviceable items from site complete all as specified and directed.

Taking up or down steel water tubings and fittings etc complete and making good disturbed surfaces of walls/ceilings etc for 20 mm bore pipe complete including stacking aside for reuse and removal of unserviceable items from site complete all as specified and directed.

Surface excavation n.exc.30 cm deep and averaging 15 cm deep and getting out in soft/loose soil including clearing away all grass vegetation, saplings, shrubs, brush wood, under growth, roots and trees n. exc. 30cm girth and removing rubbish upto a distance of 50 metre out of the periphery of the area complete all as specified and as directed.

Excavating in trenches, n.exc 1.5 m wide and n.exc 1.5 m depth for foundation etc or for shafts, wells, cesspits ,manhole pier hole, laying of cables, pipes etc n.exc 10 sqm on plan and n.exc 1.5m in depth and getting out in any kind of soil Note : Manual excavation to be done. During excavation if any damage occured to existing cable any type/ water pipe line, it will be contractor responsibilty to get it repair and make functional by providing jointing kit etc without any extra cost. Contractor has to repair it within 24 hrs so that essential service can not be effected due to such damage.If contractor fails to repair it within 24 hrs penalty @ Rs 500/- will be charged to contractor. In this GE decision will be final, conclusive and binding.

All as per item No 13.00 here-in-above but depth exc 1.50 m but n.exc 3.00 mtr complete all as specified and directed.

Returning filling in including spreading levelling watering and well ramming in layers n. exc 25 cm thick complete all as specified and directed.

Removal of excavated soil to a distance not exc 50 m and depositing where directed at a level not exc 1.5 mtr above the starting point complete all as directed.

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out soft/loose soil,and removing surplus soil to a distance n exc 50m and making good surface complete all as spd and directed.

M&L for Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering complete all as specified and directed.

M&L for Kankar or laterite,with mix of fly ash ,clinker & stone dust in the proportion of 1:3:6 ( i.e. 10% fly ash,30% clinker & 60% stone dust ) laying in layers n.exc 100mm thick ,watering ,ramming and compacted complete all as directed by Engg-in-charge .

M&L for hardcore of gauge not exceeding 63 mm of broken stone, deposited, spread and levelled layers not exceeding 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for sand filling under floors or in foundations including watering and consolidation complete all as specified and directed.

M & L for PCC (1:4:8) Type D2 using 40 mm graded crushed stone aggregate used as in sub base floor/pavings and finishing complete all as specified and as directed.

M & L for Plain Cement Concrete Type C2 1:3:6 (using 20 mm graded crushed stone aggregate) as foundation and mass filling as in post holes complete all as spd and directed.

M & L for Reinforced cement concrete (Design mix M-25 with using 20mm graded crushed stone aggregate) in foundation footings, bases for column, plinth beam etc complete all as specified and directed.

M & L for Reinforced cement concrete (Design mix M-25 with using 20mm graded crushed stone aggregate) in columns complete all as specified and directed.

M & L for Reinforced cement concrete (Design mix M-25 with using 20mm graded crushed stone aggregate) in Beams, lintels over 1.5m span complete all as specified and directed.

M & L for Reinforced cement concrete (Design mix M-25 with using 20mm graded crushed stone aggregate) as in slab supported on wall, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like etccomplete all as specified and directed.

M&L for Steel Centering and shuttering including strutting, propping etc. and removal of form to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter

M&L for Steel Centering and shuttering including strutting, propping etc. and removal of form to sides of pillars, posts, struts, piers, columns and stanchions for fair finished surface of concrete Complete all as specified and directed.

M&L for Steel Centering and shuttering including strutting, propping etc. and removal of form to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc. for fair finished surface of concrete, complete all as specified and directed.

M&L for Steel Centering and shuttering including strutting, propping etc. and removal of form to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping), for fair finished surface of concrete, all as specified and as directed.

M & L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M & L for Mild steel TMT bars 6mm to 8mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

S & F Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment using Fe 410 -W (Gde E- 250) quality A complete all as specified and directed..

S & F for rolled sections as in main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails and guides for doors, fixed with angle cleats or other connecting plates FE-410-W (Gde E-250) quality -A ,complete all as spd and directed.

S & F rolled mild steel in framed work as in doors or gates of angle or other section with gusset plates, rails, braces etc, complete drilled for fixing of steel sheeting or other covering, door etc to be prepared for sliding with and including either hooks and hinges, also fastening and fixing complete all as specified and directed.

S & F Roof trusses (framed) of angle iron members trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc complete all as specified and directed.

S & F for Hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts complete all as spd and directed.

Welding in repairs exc 2.5cm but n exc 5cm in length with thickness of metal to be welded exc. 20mm but n.exc 25mm for windows and ventilators complete all as specified and directed.

M & L for pre-painted hot-dip aluminium-zinc alloy metallic coated of any profile steel sheet corresponding to IS 15965:2012 of durability class 3, atmospheric classification category 3, coating class AZ150, 0.50 mm thick, of an approved colour and having yield strength of 550 MPa as in roof covering fixed with self tapping screws as specified up to anyheight including all necessary scaffolding and safety measures complete all as specified and directed.

M & L for pre-painted hot-dip aluminium-zinc alloy metallic coated plain steel sheet as per IS 15965:2012 of durability class 3, atmospheric classification category 3, coating class AZ150, 0.50 mm thick, of an approved colour and having yield strength of 550 MPa as in ridge/ valley/ gutter fixed with self tapping screws as specified any height Mtr height including all necessary scaffolding and safety measures complete all as specified and directed.

M & L for Brickwork with fly ash old sized bricks, straight or curved on plan exc 6 m mean radius, built in CM 1:6 complete all as specified and directed..

M&L brick work , half bricks thick , withfly ash bricks straight or curved on plan exc 6 m mean radius build in CM 1:6 all as specified as directed.

M&L for 15 mm thick cement plaster in cement mortar (1:6) as on walls, finishedfair and even complete all as specified and directed.

M&L for Rendering 15 mm thick cement plaster in CM 1:4 on fair faces of brick/concrete surfaces finished fair and even, mixed wth water proofing compound admixture (if directed) as per manufacturer's instruction, complete all as specified and directed. Note :- WPC will measuered and paid separatly under relevant item of schedule.

Supply only liquid water proofing compound complete all as specified and directed..

S & F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded palin colour PVC `C' channel heaving a PVC sheert strip of 20mm width suck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bbottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S frame wedded/ sealed to the stiles, & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing complete all as specified and directed.

M&L for external teak wood lipping, 6mm thick fixed with nails complete all as specified.

Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge.

S&F for 4mm thick figured glass, pin head type and glazing with rubber gasket in squares n exc 0.5 sq. m in each pane complete all as specified and directed.

S & F stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed..

S&F 100 mm long butt hinges, stain less steel with galvanised mild steel hinge pin, anodised and fixed , type B-21 complete all as specified and directed.

S&F aluminium anodised 150 mm barrel tower bolts of extruded section complete all as specified and directed.

S&F 150 mm long aluminium alloy handles,fabricated type, anodised complete all as specified and directed.

M & L 75 mm thick plain cement concrete M 10(Nominal Mix) using 40 mm nominal size graded crushed stone aggregates finished surface even and rough as as in sub base floor/paving/hardstanding complete all as specified and directed.

M&L for 75 mm thick cement concrete M10 (Nominal Mix) with 40mm graded crushed aggregate finished even and fair laid to a slope of 1 in 12, laid in alternate bays, each bay not exceeding 3 m length with joint filled with bituminous mastic filling comprising a mixture of 1 part of heated Industrial bitumen 85/25 grade and two parts of heated sand as in plinth protection complete all as specified.

M&L for Non Skid coloured ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 Sqm but not exc. 0.18 Sqm, in floors etc. Set and jointed in neat cement slurry and pointed in white or coloured cement to match and including over screed bed or bedding layer of mortar 15 mm thick laying floor finished in CM 1:6 complete all as specified and directed.

M&L for Glazed ceramic tiles Coloured 450 x 300mm 7 to 8 mm thick in wall/dado etc, set & jointed in neat cement slurry & pointed in white or coloured cement to match rendering over 10 mm thick in CM 1:3 on stone masonry surfaces or surfaces other than fair face of brick work/ concrete surfaces complete all as specified and directed.

Material and labour for 25 mm thick chequered cement concrete tiles of size 30x30x25 mm mm,set ,jointed and pointed using with grey cement and pigment in floors, pavings etc including the setting and jointing in neat cement plaster or slurry 0.3 kg/sqm over 20mm thick screed bed or bedding layer in cement mortar 1:6 complete all as per specification.

M & L for 20 mm thick Granite (of any type) work (table rubbed and polished) for wall lining (veneering to wall) 12 mm thick in cement mortar 1:3 and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite stone including grinding and polishing with brass screw complete all as specified and directed.

M&L for exterior heavy duty tiles dark shade 12 mm thick (square/rectangular) each tiles exceeding 0.11 sqm but not exceeding 0.18 sqm, in shed etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and including over screed bed or bedding layer of mortar 15 mm thick laying floor finished in CM 1:6 complete all as specified and directed.

M & L for Machine pressed precast concrete coloured interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade with grey cement and pigments complete all as specified and as directed.

M&Lfactory made concrete kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified as directed.

Rounding to edges of stone slabs exposed edge, such as in steps, cooking platform and other similar situation complete all as spd and directed.

S&F 20 mm outer dia medium grade CPVC, SDR 11 & plain CPVC SDR 11 with all fittings (brass inside the fittings) and fixed complete to walls and ceiling or laid in floors complete all as specified and directed.

S&F 25 mm outer dia medium grade CPVC, SDR 11 & plain CPVC SDR 11 with all fittings (brass inside the fittings) and fixed complete to walls and ceiling or laid in floors complete all as specified and directed.

S&F in repair vitreous China wash basin white, flat back,size 550X450 mm excluding taps, waste, chain and plug and porcelain stopper but including brackets including cutting for pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe complete all as spd and as directed.

S & F in repairs vitreous china squatting pan, 'Orissa" pattern, size 580 mm X 440 mm white with ‘P’ or ‘S” trap, front or back inlet and integral foot rests, any pattern and including fixing , connector to flush pipe, lime concrete bedding and making connections to flush pipe, connector to branch pipe and anti syphonage pipes etc. including sealing the joints and making leak proof using sealant complete all as specified and as directed by Engineer-in-Charge.

S & F in repairs vitreous china wash down water closet (pedestal pattern), white including thermoplastic seats and covers of grade 2 type, flat with hinging device of bronze or brass with nickel chromium plating, fixing bolt, connector to flush pipe and making connections to flush pipe, connector to branch soil pipe and anti syphonage pipes etc. including sealing the joints and making leak proof using sealant complete all as specified and as directed by Engineer-in-Charge.

S&F Vitreous China Urinal, full stall type, white (excluding flushing cistern, flush pipe and waste pipe) bowl type (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe complete all as specified.

S&F in repairs PVC low level flushing cistern, 10 litres capacity, syphonic action type white body with inlet ball valve, float , handle, bracket, flush pipe etc complete & connecting to WC complete all as specified and directed.

S&F 15mm bore fancy type stop valve , chromium plated concealed type cast copper alloy, screwed down , high pressure , with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

S&F in repair 15mm bore fancy type stop valve , chromium plated concealed type cast copper alloy, screwed down , high pressure , with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

S&F in repair PVC connection 15mm size PTMT nuts of length 600mm complete all as specified.

S&F in repair 15mm bore pillar taps cast copper alloy,with capstan heads,chromium plated,screwed down, swan neck fancy type high pressure, with or without lettred 'HOT or COLD' with long screwed shank and fly nuts complete all as specified.

S&F as in repair bib taps cast copper alloy 15mm bore with fancy chromium plated screwed down long body, screwed for iron pipe or for brass ferrule complete all as specified.

S&F 15 mm bore angle valves, cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions complete all as specified and as directed.

Supply & fixed health faucet (ABS body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 mtr long flexible tube and ABS wall hook including making connections and fixed in positions complete in all respect as specified and as directed.

S & F in repair toilet paper holder with flat recessed type stainless steel arm fixed to walls with chromium plated berass screws complete all as specified.

S & F in repair waste coupling of PTMT (half or full threaded) 32mm bore dia of discharge pipe complete all as specified and as directed.

S & F in repair sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and as directed.

S&F as in grating square 150mm size of PTMT(minimum 100 gms) complete all as specified and directed.

S&F as in repair tubular towel rail brass chromium plated 20 mm dia `D' type 60 cm long between flanges complete all as spd and directed.

S&F as in repair chromium plated shower roses 125 mm long with or without swivel joints, any size, including fixing fixing to steel pipe or union complete all as specified and direceted.

S&F Urinal Spreader of PTMT any colour for fixing with 15 mm dia pipe complete all as specified and directed.

S&F in repairs PVC SWR pipes 110 mm bore single socketed in any length with rubber ring joint fixed to wall with steel clamps all as specified and directed . Make : Supreme/ Finolex.

S&F PVC SWR pipes 110 mm bore single socketed in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed .

S&F in repairs PVC SWR pipes 75 mm bore single socketed in any length with rubber ring joint , laid in trenches or in floors complete all as specified and directed.

S&F PVC SWR bends of 100 mm bore complete all as specified and directed.

S&F PVC SWR bends of 75 mm bore complete all as specified and directed.

S&F PVC (SWR) junction single (single T) equal or unequal provided with access door of 110 mm dia complete all as specified and directed.

Supply and fix PVC SWR Nahani/ Floor trap, multi inlet connection, plain with grating including jointing with solvent cement, dia of outlet 75 mm, water seal minimum 50 mm, complete all as specified and directed by Engineer in charge.

Material & Labour for preparation of new surfaces of plastered walls and applying Two coats of Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification. over and including a coat of primer and 1.0 mm thick white wall care putty (premium quality) over plastered surfaces of walls to prepare the surface even and smooth complete all as specified.

M&L for prepration of newly plastered surfaces of wall and applying two coat of cement base paint over one coat of primer complete all as specified and directed.

M&L for prepration of new plastered surfaces and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces.

M&L for preparing of new steel & iron surfaces of any description, not otherwise described, over 10cm width or girth and applying two coats of synthetic enameled paint over a coat of Red oxide zinc chrome primer zinc chrome complete all as specified and as directed.

M & L for laying Reinforced concrete pipes 200 mm in dia, class NP2, laid and jointed complete with collars complete all as specified and directed.

Material and labour for cement concrete bed to drain pipe for 200mm bore of pipe including forming cradles in Cement concrete 1:3:6 Type C2 using 40mm graded crushed stone aggregate complete all as specified and as directed.

M&L Cement concrete 1:3:6, type C-1(using 20mm graded crushed stone aggregate) in surface channels and drains and Manholes complete all as specified and directed.

M&L for forming 30 cm inner girth fair finished drains or channels i.e. exc 30cm inner girth in cement concrete using extra cement including forms, moulds, mitred/ stopped ends etc complete all as specified and directed.

Taking down carefully aluminium conductor point wiring (light,fan,socket or power) complete including fittings such as switches,ceiling roses, pendants, regulators ,sockets etc. and removing (except those to be reused shall be kept in safe custody at the site ) and making good disturbed surfaces of walls, floors etc.to match with the existing complete all as specified.

M & L for concealed point wiring for fan/light point controlled by one one way switch complete with 1.5 sq mm FRLSH,PVC insulated multi stranded copper conductor single core cable 1100 volts grade (Red/yellow/blue wires for phases and black wire for neutral),drawn into and including non metalic PVC rigid conduit medium grade of suitable size and conduit accessories fixed on wall, floor, roof etc. and including PVC FRLSH insulated 1.5 sq mm copper conductor for earth continuity (Green Colour) and connected to common earth dolly including sunken in GI terminal box 2.8 mm thick bakelite hylam sheet cover, ISI marked with CM/L no. for mounting switch & sockets ect. Note : a) Note :- Cost of PVC conduit, cutting chases of wal/ceilingl, making good disturbed wall surfaces including finishing with cement mortor 1:4, matching with existing colour/paint of surface are deemed to be included in the quoted rate.

All as per item No.104.00 here-in-before but 5 Amp socket on same board with other switches complete all as specified and directed..

All as per BOQ item No 104.00 here-in-before but for one power pointt using by 2.50 sq mm FRLSH,PVC insulated multi stranded copper conductor single core cable 1100 volts grade (Red Colour use for Phase & Black Colour use for Neutral), and with and including FRLSH,PVC insulated multi stranded copper conductor single core 2.50 sq mm conductor for earth continuity (Green Colour) , on independent board ( but Not below the switch board of light points in the same vertical plane) complete all as specified and directed.

All as per BOQ item No 104.00 here-in-before but for one power pointt using by 4.0 sq mm FRLSH,PVC insulated multi stranded copper conductor single core cable 1100 volts grade (Red Colour use for Phase & Black Colour use for Neutral), and with and including FRLSH,PVC insulated multi stranded copper conductor single core 4.0 sq mm conductor for earth continuity (Green Colour) , on independent board ( but Not below the switch board of light points in the same vertical plane).

Material & Labour for point wiring complete with 1.5 sq mm FRLSH, PVC insulated multi stranded copper conductor single core cable 1100 volts grade (Red Colour use for Phase & Black Colour use for Neutral),drawn into and including PVC casing- caping (double interlock type) of not less than 20mm width with accessories and fittings such as bends, elbows, tees, crosses, junction box etc, fixed on wall/ceiling with GI saddles, GI screws, rawl plugs etc. for one light/fan/ bell point controlled by one switch including pressed steel terminal box powder coated of suitable size with 3 mm thick plastic laminated sheet cover of approved make for housing/mounting switches, sockets & regulators etc. and drawing 1.5 sq. mm copper solid conductor PVC insulated, unsheated cable as earth continuity conductor, connected to common earth and earth dolly , all as specified and directed by Engineer-in-Charge Note :- Cost of PVC casing & capping, making good disturbed wall surfaces including finishing with cement mortor 1:4, matching with existing colour/paint of surface are deemed to be included in the quoted rate.

Supply and fixed switch piano flush type, single pole , 5/6 Amps, one way complete all as specified.

Supply and fixed socket outlet 2 in 1 multipurpose 3 pin , (6 Amps ) flush type controlled by one switch duly marked complete all as specified and directed.

Supply and fixed socket combination outlet 2 in 1 multipurpose 5 pin , (6 Amps ) flush type 230/240V controlled by one switch duly marked complete all as specified and directed.

Supply & Fixing switch 16 Amps, 230/240 V complete all as specified and as directed by EIC.

Supply and fixed socket outlet 2 in 1 , 6 pin , (16 Amps ) flush type controlled by one switch complete all as specified and directed by EIC.

Supply & fixed ceiling rose surface bakelite 65 mm x 50 mm two to three terminal suitable for 230 Volts AC 6 Amps complete all as specified.

Supply & fixed lamp holder, polycarbonatebody with back plate straight or angular suitable for batten fittings complete all as specified.

S & F in repair LED street lights nominal power 35 Watt, LED of Make Osram; Everlight; Philips; Nicha; Cree; Samsung, LED wattage of minimum 1 watt each and Maximum 3 watt each, operational voltage of 170 volts to 270 volts, frequency of 50 Hz, lumen efficacy of minimum 110 lumens per watt, built-in integrated electronic LED driver, output open /short circuit protection, phase to phase protection, over voltage protection, surge voltage protection upto 4 KVs, protection grade IP 66, CRI greater than 80%, CW available CCT of 5700K, power factor of minimum 0.95, pressure die-cast aluminium alloy housing with epoxy powder coated metallic silver finish after phosphochromate treatment, life span of minimum 50000 working hours including fixing at any height and including wiring using three core PVC insulated, PVC sheathed, flexible stranded copper conductor FR-LSH cables suitable for outdoor use, 1.5 sqmm as per IS 694: 2010 complete all as specified and as directed.

S&F in repairs LED 20 Watt tube light fitting intregated type, including LED retrofit tube lamp 20 W , LED tube light nominal power 20 Watt, LED wattage of minimum 1 watt each and Maximum 3 watt each, operational voltage of 170 volts to 270 volts, frequency of 50 Hz, , lumen efficacy of minimum 110 lumens per watt, , integrated electronic driver (SMP based constant current supply) with output short circuit protection and surge protection upto 2.5 KV, protection grade IP 20, CRI greater than 80%, bema angle of 120 clear, THD below or less than 20%, CW available CCT of 6500K, power factor of minimum 0.95 life span of minimum 50000 working hours and LED batten with aluminium housing and polycarbonate diffuser complete fitting including connecting with PVC insulated multistranded copper flexible cable 1.0 sqmm three core, and PVC round/ square box white colour x 2 Nos for mounting of fitting complete all as specified & directed. Note (i) Make of batten and LED tube lamp should be of same make.

S&F in repairs LED 9/10 Watt tube light fitting mirror intregated type, including LED retrofit tube lamp 9/10 W , LED tube light nominal power 9/10 Watt, L LED wattage of minimum 1 watt each and Maximum 3 watt each, operational voltage of 170 volts to 270 volts, frequency of 50 Hz, , lumen efficacy of minimum 115 lumens per watt, , integrated electronic driver (SMP based constant current supply) with output short circuit protection and surge protection upto 2.5 KV, protection grade IP 20, CRI greater than 80%, bema angle of 120 clear, THD below or less than 20%, CW available CCT of 6500K, power factor of minimum 0.95 extruded aluminium LED battens life span of minimum 50000 working hours complete fitting including connecting with PVC insulated multistranded copper flexible cable 1.0 sqmm three core, and PVC round/ square box white colour x 2 Nos for mounting of fitting including taking down old unserviceable complete all as specified & directed. Note : Make of batten and LED tube lamp should be of same make.

Supply & fixing exhaust ventilation fan with louvers of sweep 380 mm,230 volts 1200 Rpm, with blade and frame and loures steel body heavy duty complete with ,ISI marked complete all as directed by Engr-in-Charge.

S&F exhaust ventilation fan with louvers of sweep 300mm 230 volts 1200 Rpm, with blade and frame and loures sturdy engineering plastic complete with ,ISI marked complete all as directed by Engr-in-Charge.

Supply & fixing exhaust ventilation fan with louvers of sweep 225mm,230 volts, with blade and frame and loures steel body, ISI marked complete all as directed by Engr-in-Charge.

S & F sheet metal enclosure for MCB, DB, SPN, 240 Volts, 100 Amps rated busbar, Confirming to IS as per IEC 61439-3, 8 way Double door enclosure made up of CRCA sheet steel, RAL 9003 powder coated, IP 43 , IK 09 including fixing the DB box flush in wall of any type and making good the distrubed surface to match as the existing with all as specified and directed by Engr-in-charge.

S & F sheet metal enclosure for MCB, DB, SPN, 240 Volts, 100 Amps rated busbar, Confirming to IS as per IEC 61439-3, 4 way Double door enclosure made up of CRCA sheet steel, RAL 9003 powder coated, IP 43 , IK 09 including fixing the DB box flush in wall of any type and making good the distrubed surface to match as the existing with all as specified and directed by Engr-in-charge.

S & F sheet metal enclosure for MCB, DB, SPN, 240 Volts, 100 Amps rated busbar, Confirming to IS as per IEC 61439-3, 2 way Double door enclosure made up of CRCA sheet steel, RAL 9003 powder coated, IP 43 , IK 09 including fixing the DB box flush in wall of any type and making good the distrubed surface to match as the existing with all as specified and directed by Engr-in-charge.

Supply and fixed MCB SP, 6 to 32 Amps, 'C' series 10kA, 240 Voltsand to be housed in DBs including necessry connection complete all as specified and directed. (Note :- Proper and suitable size cable lugs to be fixed with MCB are included in unit rate of each MCB of any rating).

Supply and fixed MCB SPN 32/40 Amps, 'C' curve, 240 Volts,ISI marked and to be housed in DBs complete including necessry connection all as specified and directed. (Note :- Proper and suitable size cable lugs to be fixed with MCB are included in unit rate of each MCB of any rating).

Supplly and fixing post top lantern LED type 20 watt 230 volts AC outdoor type with decorative post top for 360 degree indirect light IP 65 Protection with impact and corrosion resistant complete with driver and lamp complete all as directed by EIC.

Supplly and fixing post top lantern LED type 40 watt 230 volts AC outdoor type with decorative post top for 360 degree indirect light IP 65 Protection with impact and corrosion resistant complete with driver and lamp complete all as directed by EIC.

Material and labour for earthing complete with Galvanised steel earth plate electrode 600x600x6 mm mm buried directly in ground (Earth pit not less than 2.25m below ground level) with top edge of the plate not less than 1.5m below normal ground level, connected to GI wire 4 mm as earth lead by means of bolt, nuts, check nuts and washers of galvanised iron or steel, upto 7.5m length, earth strip protected by and including 15 mm dia GI pipe (light grade) and connected to main test point or body of pole/pannel or lightening arrester of main controlling switch as directed including concrete pit in PCC (1:3:6) type C1 , Precast RCC (1:2:4) Type B1 cover slab of size 54x54x5 cm reinforced with 8 mm dia TMT bars @ 100 mm C/C both ways with one handle for lifting made out of 10 mm dia TMT bar embedded in precast cover slab, funnel, wire mesh, 20 mm bore GI Pipe (Medium Grade) for watering, Charcoal and salt in alternate layers of 15 cm (Compacted Thickness) around the earth electrode including necessary excavation, earth work in any type of soil and disposal of spoil to a distance n.exc 50 m and necessary testing complete all as shown in Electrical Plate No 3 of SSR Part-I. NOTE : 1. The unit rare includes for protectionh GI pipe of 15mm and watering pipe of 20mm bore including excavation for earth pit in any type of soil/disintegrate rock. 2. Contractor has to bring agriculture soil from outside of defence land and fill in earth pit to acheive desired result as the soil resisitivity is very high. 3. The cost of GI wire including protection pipe, from top of earth plate upto 7.5 meter above/below ground level is deemed to be included in the unit rate. 4. All the joints in GI wire and connectgion with earth plate to be welded through brazing and in addition by providing double brass nut bolt and washer. 5.Costing of welding and nut bolts are deemed to be included in the unit rate.

Supply, Laying and testing cable LT XLPE sheathed,PVC insulated screened PVC bedded,galvanised steel strip of wire armoured electric power cable heavy duty with solid aluminium conductor 1100 volt grade, laid in trenches/surface of wall/in GI pipe along with pole for connection to OH lines,including brass cable glands,clamps,etc of 2 core 6 sqmm.

M&L Sand Cushioning (dry) in trenches for protection of UG Cables (below, above and around the UG Cable laid in Trenches) of 230mm Spread thickness and consolidated (punned) upto 180mm thickness, complete all as specified and as directed. (NOTE : For the purpose of Payment, Punned thick-ness of Sand Cushioning only shall be Measured and Paid )

Supply and fixing GI Light grade 40 mm dia of size for road cross/cutting on wall floor drain etc complete all as directed specified.

Supply and laying well burnt Bricks , locally available best quality (sub class "B" bricks) laid in trenches perpandicular to U/G cable for cable protection complete all as directed specified.

Material and labour for laying of GI tubing 25 mm bore, medium grade, ISI marked, conforming to IS 1239 (Part-1): 2004 including all fittings conforming to IS 1239 (Part-2): 2011 like elbow, socket, tee, reducer, nipple, short piece, union etc as required at site and laid in trenches incl connecting with existing lines all as directed by Engr-in-charge. Note:(i) Union or long screw have to provided at starting / end point of jointing pipe line . (ii) Contractor has to submit the test certificate and purchase voucher of pipes before claiming payment.

Material and labour for laying of GI tubing 40 mm bore, medium grade, ISI marked, conforming to IS 1239 (Part-1): 2004 including all fittings conforming to IS 1239 (Part-2): 2011 like elbow, socket, tee, reducer, nipple, short piece, union etc as required at site and laid in trenches incl connecting with existing lines all as directed by Engr-in-charge. Note:(i) Union or long screw have to provided at starting / end point of jointing pipe line . (ii) Contractor has to submit the test certificate and purchase voucher of pipes before claiming payment.

Supply and fix 25 mm bore dia pipe gun metal globe or gate valves, yoke type, full opening with iron wheel head, screwed both ends heavy duty, ISI marked complete for iron pipes complete all as specified and directed.

Supply and fix 40 mm bore dia pipe gun metal globe or gate valves, yoke type, full opening with iron wheel head, screwed both ends heavy duty, ISI marked complete for iron pipes complete all as specified and directed.

S & F rotational moulded polyethylene ISI marked (vertical cylindrical with close top) as per IS 12701: 1996 of 1000 litres capacity hoisted and fixed in position with and including Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for 25mm bore dia iron pipe, provision of 20 mm /25 mm dia medium grade GI pipe for connecting inlet, outlet, over flow and washout pipes including dismantling the existing one and removing to store complete all as specified and as directed.

M&L cutting existing steel tubing for alteration or addition of size 40 to 50mm dia GI pipe complete all as directed by EIC.

Intime Commotrade Pvt Ltd (BID ID -3472687)

SPS TRADING (BID ID -3472635)