Construction of Club House cum Community Centre along with swimming pool at Heart Beat-02, plot GH 01D, Sector -107, Noida

S. No. Description Total Amount Remarks

GRAND TOTAL 209,018,266.60

BILL OF QUANTITY BASED ON DSR-2021

S. NO. DSR NO. DESCRIPTION OF ITEM UNIT QUANTITY DSR RATE DSR AMOUNT NDSR RATE NDSR AMOUNT

I SUB HEAD-I :- DISMANTLING WORK

Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and

1 15.3 disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge. Cum 11.00 2,928.10 32,209.10

Extra for scrapping, cleaning and straightening reinforcement from R.C.C. or R.B. work.

Hacking of CC flooring including cleaning for surface etc. complete as per direction of the

Engineer-in-Charge.

II SUB HEAD-II :- REINFORCEMENT CEMENT CONCRETE -

REINFORCEMENT CEMENT CONCRETE -

3 5.9 Centering and shuttering including, propping etc and removal of form for : -

5.9.1 Foundations, footings, bases of columns, etc. for mass concrete sqm 15.98 307.95 4,921.29

5.9.6 Columns, Pillars, Piers, Abutments, Posts and Struts sqm 2,136.09 804.25 1,717,947.20

5.9.3 Suspended floors, roofs, landings, balconies and access platform sqm 5,004.54 766.55 3,836,231.27

5.9.5 Lintels, beams, plinth beams, girders, bressumers and cantilevers sqm 3,415.31 608.35 2,077,706.20

Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc

Steel reinforcement for R.C.C. work including straightening, cutting,

bending, placing in position and binding all complete above plinth level.

5.22A.6 Thermo-Mechanically Treated bars of grade Fe-500D or more. Kg 414,643.97 89.65 37,172,832.30

Providing and laying in position ready mixed or site batched design mix cement concrete for

reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural

sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in

recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve

3 5.33.1 durability and workability without impairing strength; including pumping of concrete to site of -

laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and

reinforcement as per direction of the engineer-in-charge; for the following grades of concrete.

5.33.1.1 All works upto plinth level -

5.33.1.2 Concrete of M30 grade with minimum cement content of 350 kg /cum cum 71.67 8,599.35 616,310.25

5.33.2.1 All works above plinth level upto floor V level -

5.33.2.2 Concrete of M30 grade with minimum cement content of 350 kg /cum cum 1,820.41 10,221.70 18,607,666.87

III SUB HEAD-III :- BRICK WORK -

Providing and laying autoclaved aerated cement blocks masonry with 100 mm thick AAC blocks

in super structure above plinth level up to floor V level in cement mortar 1:4 (1 cement : 4 coarse

4 6.38 sand ). The rate includes providing and placing in position 2 Nos 6 mm dia M.S. bars at every Cum 220.53 8,890.80 1,960,672.93

third course of masonry work.

Digitally signed by MOHD

Providing and laying autoclaved aerated cement blocks masonry with 150mm/230mm/300 mm

thick AAC blocks in super structure above plinth level up to floor V level with RCC band at sill

level and lintel level with approved block laying polymer modified adhesive mortar all complete

5 6.47 as per direction of Engineer-in-Charge. (The payment of RCC band and reinforcement shall be Cum 432.58 6,994.15 3,025,529.98

made for seperately).

IV SUB HEAD-IV :-CLADDING WORK -

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be

specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle

green, black of any size as approved by Engineer-in-Charge, in skirting, risers of stepsand dados,

6 8.31 over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey Sqm 836.92 1,063.45 890,018.76

cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of

matching shade complete.

Providing Wall Cladding Clay Tiles in size 230mm x 75mm x 15mm thick in all shades of

'Terracotta' non-pigmented made from natural clay. The appearance and shade of tiles should be

natural clay shade or terracotta having subtle variation in shade. The tiles would be made from

special clay and firing temperature would be more than 1100° Celsius. The allowed variance in

7 MR these tiles should not be more than ± 2.5mm & top surface should be coated with Silicone and Sqm 1,544.02 3,228.00 4,984,108.83

surface water absorption should not exceed 1% and by immersion method it should be less than

8%. The work to be completed as per drawing, specification and direction of Engineer In Charge

completre in all respect.

Digitally signed by MOHD

ACCOUSTICAL WALL CALDDING -

Providing 100% Natural Material- Magnesite (Hygroscopic & biologically sound binding agent)

bonded woodwool Panel "Heradesign - Superfine series planks of 600Mm*1200Mm *25Mm

thickness made out of wood wool fibre of width 1Mm Fiber thickness mixed with Natural water

& Magnesite (No-Cement) with open & smooth surface texture. A Completly harmless

Envirenment & Human Friendly & also a disposable or recyclable Material & can last for long

span in building interiors As it has long lifespan & suitable for Indoor conditions with relative air

humidity of upto 90%. Magnesite protects the wood cells against ageing & fungal attack. To

achive upto NRC=1.00 it should be a clear gap of 200Mm from wall slab along with

the backing of Mineral of 50kg/m3. Edge Detail : AK 01 Heradesign Woodwool - Acoustical

Wall Mounting System Solutions_x005fEcologically Sound Material with high mechanical

strength with Crash test of 90Km/H with Ball Impact Test DIN18032 & EN13964 with flying

colors & A sustainable material (PEFC & FSC Certified) along with EPD Certified Acc. to EN

ISO 14025 (AUB-Environmental Product declaration).Providing 100% Natural Material-

Magnesite (Hygroscopic & biologically sound binding agent) bonded woodwool Panel

"Heradesign - Superfine series planks of 600Mm*1200Mm *25Mm thickness made out of wood

wool fibre of width 1Mm Fiber thickness mixed with Natural water & Magnesite (No-Cement)

with open & smooth surface texture. A Completly harmless Envirenment & Human Friendly &

also a disposable or recyclable

Material & can last for long span in building interiors As it has long lifespan &

suitable for Indoor conditions with relative air humidity of upto 90%.

Magnesite protects the wood cells against ageing & fungal attack. To achive

upto NRC=1.00 it should be a clear gap of 200Mm from wall slab along with

the backing of Mineral of 50kg/m3. Edge Detail : AK 01

Heradesign Woodwool - Acoustical Wall Mounting System SolutionsEcologically Sound

Material with high mechanical strength with Crash test of

90Km/H with Ball Impact Test DIN18032 & EN13964 with flying colors & A

sustainable material (PEFC & FSC Certified) along with EPD Certified Acc. to EN

ISO 14025 (AUB-Environmental Product declaration).Providing 100% Natural Material-

Glass Partition

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc.

9 MR with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the -

directions of engineer-in-charge .

With Toughened glass 12 mm thickness Sqm 656.55 - - 3,626.00 2,380,634.80

Digitally signed by MOHD

Providing and fixing '' Glass Fibre Reinforced Concrete (G.F.R.C) Jali casted with 'Spray Mix'

concrete design in approved size, pattern, thickness (Border 40-50mm thick & Internal Member

15-20mm thick) and shade. The Elements should be made from ‘43 grade’ Ordinary Portland

Cement manufactured by ‘JK Cement’ / 'Birla white' / Ultratech / Nuvoco. White Quartz fine

graded sieve Silica Sand, Alkali Resistant Glass Fiber manufactured by 'NEG Japan, Owen

Corning ‘Saint Gobain’ or equivalent, Super Plasticizers manufactured by ‘Karochem’ or

equivalent, Polymers manufactured by ‘Nova Polychem’ or equivalent and U.V resistant

Synthetic inorganic pigments should be used for pigmentation manufactured by ‘Phenochem

industries or equivalent. The Elements casting shall take place with layering methodology using-

Direct Power Spray machines. The GRC Elements flexural strength average L.O.P should be

above or equivalent to 6 N/mm2 & M.O.R should be above or equivalent to 12 N/mm2 for tests

done on 28 days cured samples. The fixing of Elements should be done using ‘Dry fixing’ method

onto structural support members i.e. R.C.C, Brick work or Red Oxide Primer -paint or Epoxy

10 MR primer -paint treated mild steel. The fixtures, fasteners and self-tapping screws to be used for dry Sqm 378.43 6,880.00 2,603,581.20

fixing should be of HP/STEEL GRIP/KLIMAS/Fischer, SS 304 Clamps of 40x40x40x3mm to be

used. The quantity of fasteners or self-tapping screws shall be calculated in accordance to the

weight of Elements and actual site fixing conditions. Welding Electrodes to be of M/s ESAB /

ADANI / VICTOR. Joints to be left open for any expansion & contraction due to changes in

temperature. If at all there is a requirement of Joint filling, then Elastomeric exterior grade

paintable PU Sealant to be used. For final finishing of Element one weather shield exterior grade

water based diluted paint coat will be done if required. Vendors shall submit shop drawings of

the same, the drawings to be duly approved by the Engineer in charge at site

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid plain

flush door shutter of required size comprising of virgin polymer of K value 58-60 (Suspension

Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic

additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum

and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength

50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A

11 26.87 category with property of being termite/ borer proof, water/moisture proof and fire retardant and

fixing with stainless steel butt hinges of required size with necessary full body threaded star

headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. (Note: stainless steel

butt hinges and necessary S.S screws shall be paid separately)

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid

door/window/Ceosetory windows & other Frames/Chowkhat comprising of virgin PVC polymer

of K value 58- 60 (Suspension Grade), calcium carbonate and natural fibers (wood

powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100

gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body

threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal

strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2,

modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with

property of being termite/borer proof, water/moisture proof and fire retardant and fixed in

position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete as per

direction of Engineer-In- Charge. (M.S hold fast/lugs or SS dash fasteners shall be paid for

Note: For WPC solid door/window frames, minus 5mm tolerance in dimensions

i.e depth and width of profile shall be acceptable. Variation in profile dimensions on plus side

shall be acceptable but no extra payment on this account shall be made.

V SUB HEAD-V :- WOOD WORK -

Digitally signed by MOHD

Providing wood work in frames of doors, windows, clerestory windowsand other frames, wrought

framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length

12 9.1 (hold fast lugs or dash fastener shall be paid for separately). -

9.1.1 Second class teak wood Cum 2.13 131,576.95 280,332.92

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative

type, core of block board construction with frame of 1st class hard wood and well matched teak 3

13 9.5 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters . 35 -

mm thick including ISI marked Stainless Steel butt hinges with necessary screws

9.5.1 Second class teak wood -

Providing and fixing 12 mm thk Farmeless glass Door including fixing, hardwares etc complete

under the direction of engineer in charge

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded

built up standard tubular sections/ appropriate Z sections and other sections of approved make

conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including

necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM

rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and

15 21.1 jointed mechanically wherever required including cleat angle, Aluminium snap beading for -

glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings

and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for

21.1.1.2 Powder coated aluminium (minimum thickness of powder coating 50 micron) Kg 199.19 466.30 92,881.36

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and

making provision for fixing of fittings wherever required including the cost of EPDM rubber /

neoprene gasket required (Fittings

shall be paid for separately)

21.1.2.2 Powder coated aluminium (minimum thickness of powder coating 50 micron) Kg 184.34 564.80 104,114.10

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc.

with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the

directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):

21.3.2 With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm) Sqm 25.22 1,325.55 33,427.72

Providing and fixing fire resistant door frame of section 50 x 60 mm on horizontal side & 35 x 60

mm on vertical sides having built in rebate made out of 1.6 mm thick GI sheet (Zinc coating not

less than 120gm/m²) suitable for mounting 120 min Fire Rated Glazed Door Shutters. The frame

shall be filled with Mineral wool Insulation having density min 96Kg/m³ . The frame will have a

provision of G.I. Anchor fastners 14 nos ( 5 each on vertical style & 4 on horizontal style of size

M10 x 80 ) suitable for fixing in the opening along with Factory made Template for SS Ball

Bearing Hinges of Size 100x89x3mm for fixing of fire rated glazed shutter. The frame shall be

finished with a approved fire resistant primer or Powder coating of not less than 30 micron in

desired shade as per the directions of Engineer - in- charge . (Cost of SS ball bearing hinges is

Digitally signed by MOHD

Providing and fixing 60 mm thick glazed fire resistant door shutters of 120 min Fire Rating

confirming to IS:3614 (Part II) or EN1634- 1:1999, tested and certified as per laboratory

approved by Engineer-in-charge, with suitable mounting on door frame, consisting of vertical

styles, top rail & side rail 60 mm x 60 mm wide and bottom rail of 110 mm x 60 mm made out of

1.6mm thick G.I. sheet (zinc coating not less than 120gm/m²) duly filled mineral wool insulation

19 9.162 having density min 96 kg/m³ and fixing with necessary stainless steel ball bearing hinges of size Sqm 87.38 9,736.05 850,774.99

100x89x3mm of approved make, including applying a coat of approved fire resistant primer or

powder coating not less than 30 micron etc all complete as per direction of Engineer-in-charge

(panelling to be paid for seperately).

WOODEN HARDWARE -

Providing and fixing bright finished brass hanging type floor door stopper with necessary screws,

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having

brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width

21 9.83 upto 700 mm), with necessary accessories and screws etc. complete. Each 19.00 1,025.65 19,487.35

Providing and fixing chromium plated brass 100 mm mortice latch and lock with 6 levers and a

22 9.88 pair of lever handles of approved quality with necessary screws etc. complete. Each 30.00 817.50 24,525.00

Providing and fixing ISI marked aluminium butt hinges anodised (anodic coating not less than

23 9.95 grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade with necessary -

screws etc. complete

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than

24 9.97 grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary -

screws etc. complete :

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade

AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws

etc. complete :

GLASS DOOR HARDWARE -

Providing and fixing double action hydraulic floor spring of approved brand and manufacture

conforming to IS : 6315, having brand logo embossed on the body / plate with double spring

mechanism and door weight upto 125 kg, for doors, including cost of cutting floors, embedding in

26 21.4 floors as required and making good the same matching to the existing floor finishing and cover -

plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per

the direction of Engineer-in-charge.

21.4.1 With stainless steel cover plate minimum 1.25 mm thickness Each 48.00 2,448.85 117,544.80

Filling the gap in between aluminium frame & adjacent RCC/ Brick/ Stone work by providing

21.8 weather silicon sealant over backer rod of approved quality as per architectural drawings and

direction of Engineer-in-charge complete

21:08:01 Upto 5mm depth and 5 mm width Metre 200.00 85.25 17,050.00

Digitally signed by MOHD

Providing and fixing bright /matt finished Stainless Steel handles of approved quality & make

with necessary screws etc all complete.

Providing and fixing chromium plated brass 100 mm mortice latch and lock with 6 levers and a

29 9.88 pair of lever handles of approved quality with necessary screws etc. complete. Each 16.00 817.50 13,080.00

VI SUB HEAD-VI :- EXTERNAL FAÇADE -

Providing and supplying aluminium extruded tubular and other aluminium sections as per the

architectural drawings and approved shop drawings , the aluminium quality as per grade 6063 T5

or T6 as per BS 1474,including super durable powder coating of 60-80 microns conforming to

AAMA 2604 of required colour and shade as approved by the Engineer-in-Charge. ( The item

30 25.1 includes cost of material such as cleats, sleeves, screws etc. necessary for fabrication of extruded Kg 19,380.75 370.05 7,171,846.54

aluminium frame work. Nothing extra shall be paid on this account). The weight of aluminium

extruded section shall be taken for purpose of payment.

Designing, fabricating, testing, protection, installing and fixing in position semi (grid) unitized

system of structural glazing (with open joints) for linear as well as curvilinear portions of the

building for all heights and all levels, including: (a) Structural analysis & design and preparation

of shop drawings for the specified design loads conforming to IS 875 part III (the system must

passed the proof test at 1.5 times design wind pressure without any failure), including functional

design of the aluminum sections for fixing glazing panels of various thicknesses, aluminium cleats,

sleeves and splice plates etc. gaskets, screws, toggles, nuts, bolts, clamps etc., structural and

weather silicone sealants, flashings, fire stop (barrier)- cum-smoke seals, microwave cured EPDM

gaskets for water tightness, pressure equalisation & drainage and protection against fire hazard

(b) Fabricating and supplying serrated M.S. hot dip galvanised / Aluminium alloy of 6005 T5

brackets of required sizes, sections and profiles etc. to accommodate 3 Dimentional movement

for achieving perfect verticality and fixing structural glazing system rigidly to the RCC/

masonry/structural steel framework of building structure using stainless steel anchor fasteners/

bolts, nylon seperator to prevent bimetallic contacts with nuts and washers etc. of stainless steel

grade 316, of the required capacity and in required numbers. (c) Providing and filling, two part

pump filled, structural silicone sealant and one part weather silicone sealant compatible with the

structural silicone sealant of required bite size in a clean and controlled factory / work shop

environment, including double sided spacer tape, setting blocks and backer rod, all of

approved grade, brand and manufacture, as per the approved sealant design, within and all

around the perimeter for holding glass.Providing and fixing in position flashings of solid

aluminium sheet 1 mm thick and of sizes, shapes and profiles, as required as per the site

conditions, to seal the gap between the building structure and all its interfaces with curtain

glazing to make it watertight.

(e) Making provision for drainage of moisture/ water that enters the curtain glazing system to

make it watertight, by incorporating principles of pressure equalization, providing

suitable gutter profiles at bottom (if required), making necessary holes of required sizes and of

required numbers etc. complete. This item includes cost of all inputs of designing, labour for

Digitally signed by MOHD

Providing, assembling and supplying vision glass panels (IGUs) comprising of hermetically-sealed

6-12- 6 mm insulated glass (double glazed) vision panel units of size and shape as required and

specified, comprising of an outer heat strengthened float glass 6mm thick, of

approved colour and shade with reflective soft coating on surface # 2 of approved colour and

shade, an inner Heat strengthned clear float glass 6mm thick, spacer tube 12mm wide, dessicants,

including primary seal and secondary seal (structural silicone sealant) etc. all

complete for the required performances, as per the Architectural drawings, as per the approved

32 25.3 shop drawings, as specified and as directed by the Engineer-in-Charge. The IGUs shall be

assembled in the factory/ workshop of the glass processor. (Payment for fixing of IGU Panels in

the curtain glazing is included in cost of item No.25.2) For payment, only the actual area of glass

on face # 1 of the glass panels (excluding the areas of the grooves and weather silicone sealant)

provided and fixed in position, shall be measured in sqm

(i) Coloured tinted float glass 6mm thick substrate with reflective soft coating on face # 2, +

12mm Airgap + 6mm Heat Strengthened clear Glass of approved make having properties

as visible Light transmittance (VLT) of 25 to 35 %, Light reflection internal 10 to 15%, light

reflection external 10 to 20 %, shading coefficient (0.25- 0.28) and U value of 3.0 to 3.3 W/

m2 degree K etc. The properties of performance glass shall be decided by technical sanctioning Sqm 1,292.05 3,377.50 4,363,898.88

authority as per the site requirement.

Extra for openable side / top hung vision glass panels (IGUs) including providing and supplying

at site all accessories and hardwares for the openable panels as specified and of the approved

make such as heavy duty stainless steel friction hinges, min 4 -point cremone

locking sets with stainless steel plates, handles, buffers etc. including necessary stainless steel

screws/ fasteners, nuts, bolts, washers etc. all complete as per the Architectural drawings, as per

the approved shop drawings, as specified and as directed by the Engineer- in- Charge.

Structural steel work in single section, fixed with or without connecting

34 10.1 plate, including cutting, hoisting, fixing in position and applying a priming kg 25,841.00 93.05 2,404,505.05

coat of approved steel primer all complete.

Painting with synthetic enamel paint of approved brand and

manufacture to give an even shade :

13.61,1 Two or more coats on new work Sqm 646.03 131.45 84,919.99

Toilet Cubicles -

Supply and Installation of Modular Toilet cubicles as per description Athena Lite Series (SS +

Aluminium ) Shade- Thickness of compact laminate board = 12mm and a gap of 150 mm from

the ground with standard height as per drawing/site requirment.

Accessories in SS 316 for all bottom accessaries and other in SS 304 as per direction of EIC,

drawing, specification etc complete in all respect.

1. Alluminium Wall bracket for H-top rail

2. Aluminium U-channel

4. SS Privacy thumb turn with occupancy indicator.

5. SS Hinges with cover 6. SS Coat Hook

7. Alluminium Door Stopper channel

8. Rubber door stoper lining

9. U Channel -SS

VII SUB HEAD-VI :- STEEL WORK -

37 GLASS RAILING -

Digitally signed by MOHD

Providing and fixing stainless steel (Grade 304) glass railing made of Hollow tubes, channels,

plates etc., including welding, grinding, buffing, polishing and making curvature (wherever

required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the

railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of

required size, on the top of the floor or the side of waist slab with suitable arrangement as per

MR approval of Engineer-incharge, and fixing 12mm toughened glass with the help of suitable flat Sqm 125.39 - - 10,432.00 1,308,075.78

head brushed steel bolts, The work to be completed as per drawing, specification and direction

of Engineer In Charge completre in all respect.

VIII SUB HEAD-VII :- FLOORING WORK -

Providing and laying vitrified floor tiles in different sizes (thickness to bespecified by the

manufacturer) with water absorption less than 0.08%and conforming to IS: 15622, of approved

make, in all colours and shades,laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse

sand),jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white

cement and matching pigments etc.,complete.

11.41A.3 Glazed Vitrified tiles Matt/Antiskid finish of size -

11.41A.3. Size of Tile 600x600 mm

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the

manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved

brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1

cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints

39 11.41.A with white cement and matching pigments etc. The tiles must be cut with the zero chipping -

diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of

required thickness, leveling system and rubber mallet for placing the tiles gently and easily.

11.41.A.1 Size of Tile 600 x 600 mm

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer),

with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all

colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement:

40 11.46 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with -

white cement & matching pigments etc. complete.

Providing and fixing Glass mossaic tiles on finished plain wall surface ofsize 20 mm x 20 mm x 4

mm in all colour, design , fixing in customizedesign as per direction of Engineer-in- Charge. The

glass mosaic tilesto be fixed on the wall surface with the help of approved adhesive appliedat the

41 11.53 rate of 2.5 kg per sqm and grouting of the same. The rate is inclusive of all operation, material sqm 511.47 3,282.50 1,678,895.84

and required pattern approved by Engineer-in-Charge:

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as

well as curvilinear portions of the building all complete as per the architectural drawings with 18

mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse

42 11.56 sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with -

pigment of matching shade including rubbing, curing and polishing etc. all complete as specified

and as directed by the Engineer-in-Charge.

Digitally signed by MOHD

20 mm thk Polished Granite stone slab colour of Black, Cherry/Ruby Red or equivalent

52 mm thick cement concrete flooring with concrete hardener topping, under layer 40 mm thick

cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

and top layer 12 mm thick cement hardener consisting of mix 1:2 (1 cement hardenermix : 2

43 11.4 graded stone aggregate 6 mm nominal size) by volume, hardening compound mixed @ 2 litre per Sqm 190.40 855.90 162,963.36

50 kg of cement or as per manufacturer's specifications. This includes cost of cement slurry, but

excluding the cost of nosing of steps etc. complete.

Supply & fixing of flexible pvc sheet flooring in 2 mm thickness in the size of 2 mtr X 20 mtr use

area classification 23/34/43 results from independent testing demonstrate that product inherently

inhibits the growth of microbial strain MRSA. It shall be homogeneous in construction. The

flooring shall incorporated a specially (PUR) to give polish free maintenance imported pvc vinyl

flooring with total weight 28oo g/m2,dimensional stability EN-434, static electrical charge <2kv,

44 MR impact sound reduction approx ISO 717-2, good resistant to scratch, slip, fire ,chemical & does sqm 665.24 - - 3,194.00 2,124,766.98

not favor in growth fungi & bacteria, diamond 10 coating for more durabality, duly installed on

smooth and hard surface of self levelling compound with adhesive and seamless joint. The work

to be completed as per drawing, specification and direction of Engineer In Charge completre in

Providing and fixing countertops with 12 mm thick acrylic solid surface manufactured as per ISO

19712-2. Solidsurface used should be Microbial resistant and resistant to mould growth,boiling

water resistant, heat resistant, impact resistant, stain resistant, scratchresistant as per ASTM G171

( min 800 MPa), Green Guard certified and with afire rating conforming Class 1 as per BS 476

(Part 6 and 7) and duly approvedunder IS12777 as per Indian Fire standrds. Acrylic solid surface

countertop, tobe fixed over commercial grade 18mm thick marine board, supported over an

underlaying MS Sections of 50X50X25 designed to support a weight of 25 Kg.per Sqmtr. The

pasting of Corian counter top to be done with approved grade of moisture cured Silicon Sealants

as per manufacturer's specification and guideline, The countertop scope includes fascia, back

45 MR splash, moulding ofedges, buffing of surface, making of holes for plumbing fixtures, flushing of Sqm 18.56 - - 17,547.00 325,672.32

joints, installing of necessary hardware,bowl, sealing with silicon sealants, etc asper approved

drawings etc. For measurement, plan and elevation area (horizontal and vertical) including bowl

cutout, to be measured for payment.Fabrication to be done by authorized fabricators and

supplying company to provide 5 years installed warranty on material as well as fabrication. The

work to be completed as per drawing, specification and direction of Engineer In Charge

completre in all respect.

Providing & fixing 10.5 mm thick engineerwood flooring american exotic bruce 7 layer

construction,top layer of wood veener 2mm ,plank size width 120 mm ,length 400-1200 mm

,Lock & fold locking ,premium finish,micro bevel edges/ends with an underlayment made of

46 MR natural colour foam,with accessories like end profile,transition profile,reducer ,etc.complete.The Sqm 229.16 13,387.00 3,067,764.92

profiles are 100% matching. profile at door openings The work to be completed as per drawing,

specification and direction of Engineer In Charge completre in all respect.

IX SUB HEAD-VIII :- ROOFING/ FALSE CEILING -

Providing and fixing Heat Resistant Terrace Tiles (300 mm x 300mm x 20 mm) with SRI (solar

refractive index) > 78, solar reflection> 0.70 and initial emittance > 0.75 on waterproof and

sloped surface of terrace, laid on 20 mm thick cement sand mortar in the ratio of 1:4 (1 cement : 4

47 12.55 coarse sand) and grouting the joints with mix of white cement & marble powder in ratio of 1:1, Sqm 1,759.72 1,444.90 2,542,612.35

including rubbing and polishing of the surface upto 3 cuts complete, including providing skirting

upto 150 mm height along the parapet walls in the same manner.

Digitally signed by MOHD

GYPSUM CEILING -

Providing and fixing false ceiling at all height including providing and fixing of frame work made

of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120

gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x

1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to

the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat

fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required

size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running

at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom

wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to

centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting

clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing

perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the

48 12.45 perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with -

25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling

section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm

c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with

recommended jointing

compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm

on both sides of joint and two coats of primer suitable for board, all as per manufacturer's

specification and also including the cost of making openings for light fittings, grills, diffusers,

cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings,

specification and direction of the Engineer in Charge but excluding the cost of painting with

Fully Perforated Gypsum Plaster Board of size 1200 x 2400x12.5 mm having approx. 15 %

perforated area with perforation size and pattern as approved by the Engineerin- charge and as

12.45.4 per manufacturer's specification, with all 4 side tapered and backed by acoustical tissue with Sqm 1,048.25 1,483.15 1,554,711.47

NRC value not less than 0.60 sqm 1483.15

METAL CEILING -

Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true

horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections (

galvanized @ 120 grams/ sqm, both side inclusive) consisting of main "T" runner with suitably

spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum)

sheet, spaced at 1200 mm center to center and cross "T" of size 24x25 mm made of 0.30 mm

thick (minimum) sheet, 1200 mm long spaced between main "T" at 600 mm center to center to

form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size 24x25 mm made

of 0.30 mm thick (minimum) sheet to be interlocked at middle of the

1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and

laying false ceiling tiles of approved texture in the grid including, required cutting/making,

49 12.52 opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main -

"T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm

fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with

galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center

along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with

polyester paint, all complete for all heights as per specifications, drawings and as directed by

Engineer-in-charge.

GI Metal Ceiling Lay in perforated Tegular edge global white color tiles of size 595x595 mm and

0.5 mm thick with 8 mm drop; made of GI sheet having galvanizing of 100 gms/sqm (both sides

inclusive) and 20% perforation area with 1.8 mm dia holes and having NRC (Noise

12:52:02 Reduction Coefficient ) of 0.5, electro statically polyester powder coated of thickness 60 microns Sqm 3,438.19 1,746.25 6,003,938.13

(minimum), including factory painted after bending and perforation, and backed with a black

Glass fiber acoustical fleece.

Digitally signed by MOHD

BAFFLE CEILING -

"U shaped" Roll-formed Baffle Ceiling with Fixed and Demountable Torsion Spring System of

size 25 X 65 x 0.5 mm Aluminium: -

Supply & Installation of Torsion spring Roll formed U-Baffle Ceiling System, comprising of

baffle width of 25mm and height of 65mm manufactured out of 0.5mm thick Coil Coated

Aluminium (AA 3105/ 3000 series). Panel shall be places in a module of 75mm C/C and length

upto 4000 mm of fixed baffle panel with perforation of 2mm dia Ø in a diagonal pattern 4.33mm

↔ C/C, 8.66mm↕ C/C. The baffle shall be manufactured on high speed, high precision roll

forming machine with configuration roller leveling process to ensure the flatness and to avoid the

failure of metal at corners which may occur normally on press brake machine. The coil is coated

on a continuous paint line double baked and shall be stove enamelled in a continuous coil

coating process of the approved colour on the exposed side and the reverseside with polyester

primer. The U-Baffle ceiling panels shall be mounted on coil coated customise d Hat type

Aluminium carrier of size 60mm*30mm*0.9mm thick. The customised carrier shall be suitable for

both torsion spring based & standard fixed Baffle panels. The carrier shall be suspended with M6

Threaded rod hangers spaced at 1200mmc/c. Maximum upto 20% of the total ceiling area, based

50 MR on client requirement, shall be demountable torsion spring-based panels. The length of the panel Sqm 232.61 - - 8,968.00 2,086,040.20

shall be upto 2400mm. Suspension System: As per manufacturerst and arditis recommend to have

minimum gap of 250mm between plenum and its baffle top surface height for easy engagement of

spring. The baffle ceiling system should meet the required standards for Green Pro certification

and should qualify as green product as per C -II green products and services council. The

manufacturer should be ISO9001:2015 Quality Management System Certification compliant with

in house testing facility and should have their own manufacturing plant with Roll forming

machine in India.Mode of Measurements :Measurements shall be wall to wal lwithout any

deductions for lights, diffusers, columns, etc. The work to be completed as per drawing,

specification and direction of Engineer In Charge completre in all respect.

Polycarbonate Skylight System :- -

Providing and fixing of Tuflite/DPI 16mm thick Multicell UV protected Polycarbonate Panel

System with 5 cells and 6 walls structure over structure Steel/MS purlin as per approved

colour/shade. Co-extruded UV protected panels shall have width of 900mm to ensure best

performance for wind uplift, vibration, oil canning, and visual appearance. Panels shall be

manufactured with vertical standing seam at both sides of the panel. Welding or gluing up of

standing seam is not acceptable. Panels shall be fixed on purlins with Stainless Steel retention

51 MR clip of SS-304 grade and connectors. Snap-on connectors to interlock the panels shall have a -

grip-lock double tooth locking mechanism to ensure maximum uplift capability. Panels shall have

End-cap/Aluminium U-profile/Glazing bar for ends as per requirement. Panel shall be co-

extruded with special anti-glare compound (if required) to make it anti-glare/soft light to prevent

glare and sun streaks.

Polycarbonate panels shall not have yellowness index more than - 6.86 as per ASTM G 155

when tested for minimum of 1000 hours exposed to UV light source under Xenon Arc Lamp with

irradiance 0.35 W/m2 @340 mm. -

The polycarbonate panels must satisfy Dart drop impact test as per IS-14443 shall show no sign

of breakage on Polycarbonate sheets which have been exposed to UV for a minimum of 1000

hours as per ASTM G 155. Panels shall be fixed over structural steel/MS purlins (will be paid

extra) conforming to the detail technical specifications and as per approved architectural sqm 9.21 - - 5,660.00 52,105.39

drawings. (U value - 1.62, Light transmission & Colour as approved). The work to be completed

as per drawing, specification and direction of Engineer In Charge completre in all respect.

Digitally signed by MOHD

Providing and fixing beveled edge mirror of superior glass (of approved quality) complete with 6

mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers

52 MR complete. The work to be completed as per drawing, specification and direction of Engineer In Sqm 73.26 5,911.00 433,039.86

Charge completre in all respect.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality)

complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and

washers complete.

X SUB HEAD-IX :- FINISHING -

54 13.16 6 mm cement plaster of mix : 1:3 (1 cement : 3 fine sand) sqm 15,166.02 253.05 3,837,762.09

55 13.1 12 mm cement plaster of mix : 1:6 (1 cement: 6 fine sand) sqm 1,783.45 282.00 502,932.47

Providing and applying white cement based putty of average thickness 1 mm, of approved brand

56 13.80 and manufacturer, over the plastered wall surface to prepare the surface even and smooth sqm 15,166.02 123.85 1,878,311.93

Distempering with oil bound washable distemper of approved brand

and manufacture to give an even shade :

New work (two or more coats) over and including water

thinnable priming coat with cement primer

58 13.45 Finishing walls with textured exterior paint of required shade : -

New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of

exterior primer applied @ 2.20kg/10 sqm

Painting with synthetic enamel paint of approved brand and

manufacture to give an even shade :

13.61,1 Two or more coats on new work Sqm 100.00 131.45 13,145.00

XI SUB HEAD-X :- WATER PROOFING -

Providing and applying integral crystalline slurry of hydrophilic innature for waterproofing

treatment to the RCC structures like retainingwalls of the basement, water tanks, roof slabs,

podiums, reservior,sewage & water treatment plant, tunnels / subway and bridge decketc.,

prepared by mixing in the ratio of 5 : 2 (5 parts integral crystalline slurry : 2 parts water) for

vertical surfaces and 3 : 1 (3 parts integralcrystalline slurry : 1 part water) for horizontal surfaces

and applyingthe same from negative (internal) side with the help of synthetic fiberbrush. The

material shall meet the requirements as specified in ACI- 212-3R-2010 i.e by reducing

permeability of concrete by more than90% compared with control concrete as per DIN 1048 and

resistantto 16 bar hydrostatic pressure on negative side. The crystalline slurryshall be capable of

self-healing of cracks up to a width of 0.50mm.The work shall be carried out all complete as per

specification andthe direction of the engineer-in-charge. The product performance shallcarry

guarantee for 10 years against any leakage.

22.23.1 For vertical surface two coats @ 0.70 kg per sqm Sqm 221.03 406.25 89,794.73

22.23.2 For horizontal surface one coat @1.10 kg per sqm. Sqm 290.18 311.50 90,391.07

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by

61 22.5 applying cement slurry mixed with water proofing cement compound consisting of applying: -

First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @

(a) 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours. -

Digitally signed by MOHD

Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound

(b) @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for -

The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of

pipes and masonry with polymer mixed slurry. Sqm 255.94 516.60 132,217.05

Providing and laying integral cement based water proofing treatment including preparation of

62 22.7 surface as required for treatment of roofs, balconies, terraces etc consisting of following -

Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing

compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab

(a) including adjoining walls upto 300 mm height including cleaning the surface before treatment. -

Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of

cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming

to IS : 2645 and approved by Engineerin- charge over 20 mm thick layer of cement mortar of mix

1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645

and approved by Engineerin- charge to required slope and treating similarly the adjoining walls

upto 300 mm height including rounding of junctions of walls and slabs.

After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of

cement admixed with water proofing compound conforming to IS : 2645 and approved by

Engineer-in-charge

Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse

sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-

in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally

(d) finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm -

square 3 mm deep.

The whole terrace so finished shall be flooded with water for a minimum period of two weeks for

e) curing and for final test.“All above operations to be done in order and as directed and specified -

by the Engineer-in-Charge

22.7.1 With average thickness of 120 mm and minimum thickness at khurra as 65 mm. Sqm 1,880.85 1,522.95 2,864,436.09

6.28.01/P Providing and fixing Signages and name Board all complete as specified and as directed by the

AR 2021 Engineer-in-Charge.

Fixing Rebar as per dia given below,with Hilti Hit- RE-500 or equivalent as per structural

64 MR drawing , manufacturer instructions and as instructed for anchoring/rebaring of reinforcement

bars as per direction of engineer in charge.

25 MM Dia Bar and above Nos 100.00 1,500.00 150,000.00

65 7019 Dash fastener / Chemical fastener Each 500.00 12.50 6,250.00

GRAND TOTAL with DSR and NDSR 160,364,299.84

GRAND TOTAL with DSR and NDSR 160,364,299.84

Digitally signed by MOHD

SCHEDULE OF QUANTITIES FOR ELECTRICAL AND LV SYSTEM

PROJECT-HEART BEAT CITY-II_CLUB

Item Code Description Quantity Unit Rate AMOUNT

PART-A_DSR ITEM

1.10 Wiring for light point/ fan point/ exhaust fan point/ call bell point with

1.5 sq.mm FRLS PVC insulated copper conductor single core cable

in surface / recessed medium class PVC conduit, with modular

switch, modular plate, suitable GI box and earthing the point with

1.5 sq.mm. FRLS PVC insulated copper conductor single core

cable etc as required.

1.12 Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated

copper conductor single core cable in surface/ recessed medium

class PVC conduit alongwith 1 No 4 sq. mm FRLS PVC insulated

copper conductor single core cable for loop earthing as required. 2525 Metre 334 843961

1.13 Wiring for light/ power plug with 4X4 sq. mm FRLS PVC insulated

copper conductor single core cable in surface/ recessed PVC

conduit alongwith 2 Nos 4 sq. mm FRLS PVC insulated copper

conductor single core cable for loop earthing as required. 50 Metre 537 26861

1.14 Wiring for circuit/ submain wiring alongwith earth wire with the

following sizes of FRLS PVC insulated copper conductor, single

core cable in surface/ recessed PVC conduit as required

1.14.1 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire 375 Metre 233 87409

1.14.2 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire 1640 Metre 275 451389

1.14.4 2 X 6 sq. mm + 1 X 6 sq. mm earth wire 295 Metre 439 129533

1.14.5 2 X 10 sq. mm + 1 X 6 sq. mm earth wire 135 Metre 570 76889

1.14.6 2 X 16 sq. mm + 1 X 6 sq. mm earth wire 15 Metre 772 11580

1.14.10 4 X 10 sq. mm + 2 X 6 sq. mm earth wire 345 Metre 1005 346721

1.19 Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid

copper conductor PE insulated, shielded with fine tinned copper

braid and protected with PVC sheath in the existing surface/

recessed steel/ PVC conduit as required.

1.21 Supplying and fixing of following sizes of medium class PVC

conduit along with accessories in surface/recess including cutting

the wall and making good the same in case of recessed conduit as

1.24 Supplying and fixing following modular switch/ socket on the

existing modular plate & switch box including connections but

excluding modular plate etc. as required.

1.24.1 5/6 amps switch 43 Each 103 4422

1.24.4 3 pin 5/6 amp socket outlet 43 Each 122 5246

1.24.5 6 pin 15/16 amp socket outlet 61 Each 197 12011

1.24.6 Telephone socket outlet 9 Each 148 1331

1.24.7 TV antenna socket outlet 7 Each 148 1035

1.25 Supplying and fixing stepped type electronic fan regulator on the

existing modular plate switch box including connections but

excluding modular plate etc. as required. 62 Each 369 22847

1.26 Supplying and fixing modular blanking plate on the existing modular

plate & switch box excluding modular plate as required.

1.27 Supplying and fixing following size/ modules, GI box alongwith

modular base & cover plate for modular switches in recess etc as

1.27.1 1 or 2 Module (75mmX75mm) 67 Each 298 19985

1.27.3 4 Module (125mmX75mm) 10 Each 343 3433

1.27.4 6 Module (200mmX75mm) 10 Each 402 4016

1.33 Supplying and fixing 3 pin, 5 amp ceiling rose on the existing

junction box/ wooden block including connection etc as required. 12 Each 87 1040

1.45 Installation, testing and commissioning of ceiling fan, including

wiring the down rods of standard length (upto 30 cm) with 1.5 sq.

mm FRLS PVC insulated, copper conductor, single core cable,

including providing and fixing phenolic laminated sheet cover on the

fan box etc. as required. 62 Each 337 20901

1.50 Installation of exhaust fan in the existing opening, including making

good the damage, connection, testing, commissioning etc. as

1.50.1 Upto 450 mm sweep 12 Each 450 5400

1.51 Extra for fixing the louvers/ shutters complete with frame for a

exhaust fan of all sizes. 12 Each 207 2484

1.53 Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the

existing surface/ recessed Steel/ PVC conduit as required.

1.53.1 1 run of cable 450 Metre 57 25862

1.55 Wiring for group controlled (looped) light point/fan

point/exhaust fan point/ call bell point ( without independent

switch etc.) with 1.5 sq. mm FRLS PVC insulated copper

conductor single core cable in surface/ recessed PVC conduit,

and earthing the point with 1.5 sq. mm FRLS PVC insulated

copper conductor single core cable etc. as required.

2 MCCB, MCB & DB'S

2.2 Providing and fixing following rating and breaking capacity MCCB in

existing cubicle panel board including drilling holes in cubicle panel,

making connections, etc. as required.

2.3 Supplying and fixing following way, single pole and neutral, sheet

steel, MCB distribution board, 240 volts, on surface/ recess,

complete with tinned copper bus bar, neutral bus bar, earth bar, din

bar, interconnections, powder painted including earthing etc. as

required. (But without MCB/RCCB/Isolator)

2.3.1 6 way, Double door 1 Each 2206 2206

2.3.2 8 way, Double door 6 Each 2573 15438

2.3.3 12 way, Double door 4 Each 2315 9259

2.3.4 16 way, Double door 2 Each 3141 6282

2.4 Supplying and fixing following way, horizontal type three pole and

neutral, sheet steel, MCB distribution board, 415 volts, on surface/

recess, complete with tinned copper bus bar, neutral bus bar, earth

bar, din bar, interconnections, powder painted including earthing

etc. as required. (But without MCB/RCCB/Isolator)

2.4.2 6 way (4 + 18), Double door 4 Each 4974 19894

2.4.3 8 way (4 + 24), Double door 8 Each 5967 47737

2.5 Supplying and fixing of following ways surface/ recess mounting,

vertical type, 415 volts, TPN MCB distribution board of sheet steel,

dust protected, duly powder painted, inclusive of 200 amps tinned

copper bus bar, common neutral link, earth bar, din bar for

mounting MCB's (but without MCB's and incomer ) as required .

(Note : Vertical type MCB TPDB is normally used where 3 phase

outlets are required.)

2.5.1 4 way (4 + 12), Double door 1 Each 7512 7512

2.10 Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C"

curve, miniature circuit breaker suitable for inductive load of

following poles in the existing MCB DB complete with connections,

testing and commissioning etc. as required.

2.10.1 Single pole 213 Each 256 54507

2.10.3 Double pole 8 Each 656 5248

2.11 Supplying and fixing single pole blanking plate in the existing MCB

DB complete etc. as required. 82 Each 13 1027

2.12 Supplying and fixing following rating, double pole, 240 volts, isolator

in the existing MCB DB complete with connections, testing and

commissioning etc. as required.

2.14 Supplying and fixing following rating, double pole, (single phase and

neutral), 240 volts, residual current circuit breaker (RCCB), having

a sensitivity current upto 300 milliamperes in the existing MCB DB

complete with connections, testing and commissioning etc. as

2.18 Supplying and fixing 20 amps, 240 volts, SPN industrial type,

socket outlet, with 2 pole and earth, metal enclosed plug top

alongwith 20 amps "C" curve, SP, MCB, in sheet steel enclosure,

on surface or in recess, with chained metal cover for the socket out

let and complete with connections, testing and commissioning etc.

as required. 64 Each 1621 103764

2.19 Supplying and fixing 20 amps, 415 volts, TPN industrial type,

socket outlet, with 4 pole and earth, metal enclosed plug top

alongwith 20 amps "C" curve, TPMCB, in sheet steel enclosure, on

surface or in recess, with chained metal cover for the socket out let

and complete with connections, testing and commissioning etc. as

required. 2 Each 2590 5181

2.21 Providing and fixing M.V. danger notice plate of 200 mm X 150 mm,

made of mild steel, at least 2 mm thick, and vitreous enameled

white on both sides, and with inscription in single red colour on front

side as required. 4 Each 269 1074

4.6 Supplying and installing following size of perforated Hot Dipped

Galvanised iron cable trays (Galvanisation thickness not less than

50microns) with perforation not more than 17.5%, in convenient

sections, joined with connectors, suspended from the ceiling with

G.I. suspenders including bolts & nuts, painting suspenders etc as

4.6.2 150 mm width X 50 mm depth X 1.6 mm thickness 20 Metre 716 14325

4.7 Supplying and installing following size of perforated Hot Dipped

Galvanised iron cable trays bends (Galvanisation thickness not less

than 50microns) with perforation not more than 17.5%,, joined with

connectors, suspended from the ceiling with G.I. suspenders

including bolts & nuts, painting suspenders etc as required.

4.7.2 150 mm width X 50 mm depth X 1.6 mm thickness 2 Each 1270 2540

4.8 Supplying and installing following size of perforated Hot Dipped

Galvanised iron cable trays Tee's (Galvanisation thickness not less

than 50microns) with perforation not more than 17.5%, joined with

connectors, suspended from the ceiling with G.I. suspenders

including bolts & nuts, painting suspenders etc as required.

4.8.2 150 mm width X 50 mm depth X 1.6 mm thickness 1 Each 1383 1383

4.10 Supplying and installing following size of perforated Hot Dipped

Galvanised iron cable trays reducers (Galvanisation thickness not

less than 50microns) with perforation not more than 17.5%, joined

with connectors, suspended from the ceiling with G.I. suspenders

including bolts & nuts, painting suspenders etc as required.

4.10.2 150 mm width X 50 mm depth X 1.6 mm thickness 1 Each 1921 1921

5.15 Providing and fixing 25 mm X 5 mm G.I. strip on surface or in

recess for connections etc. as required. 100 Metre 244 24396

5.18 Providing and fixing 6 SWG dia G.I. wire on surface or in recess for

loop earthing along with existing surface/ recessed conduit/

submain wiring/ cable as required. 75 Metre 42 3134

6 LIGHTNING CONDUCTOR

6.2 Providing and fixing of lightning conductor finial, made of 25 mm dia

300 mm long, GI tube, having single prong at top, with 85 mm dia 6

mm thick GI base plate including holes etc. complete as required.

6.7 Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or

surface of wall for lightning conductor complete as required.(For

horizontal run) 315 Metre 126 39846

6.8 Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or

surface of wall for lightning conductor complete as required.(For

vertical run) 175 Metre 197 34560

6.9 Fixing of copper/ G.I. tape 20 mm X 3 mm thick on parapet or

surface of wall for lightning conductor complete as required.(For

horizontal run) 315 Metre 80 25305

6.10 Fixing of copper/ G.I. tape 20 mm X 3 mm thick on parapet or

surface of wall for lightning conductor complete as required.(For

vertical run) 175 Metre 162 28317

6.14 Providing and laying G.I. tape 32 mm X 6 mm from earth electrode

directly in ground as required.

6.15 Laying copper/ G.I. tape 32 mm X 6 mm from earth electrode

directly in ground as required.

7 MV CABLE LAYING

7.7 Laying and fixing of one number PVC insulated and PVC sheathed /

XLPE power cable of 1.1 KV grade of following size on wall surface

7.7.1 Upto 35 sq. mm (clamped with 1mm thick saddle) 30 Metre 55 1636

9 MV CABLE JOINTING & END TERMINATION

9.1 Supplying and making end termination with brass compression

gland and aluminium lugs for following size of PVC insulated and

PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade

19.1 Supply, Installation, Testing and Commissioning of 1200 mm

sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current

(BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long

down rod, 2 nos. canopies, shackle kit, safety rope, copper winding,

Power Factor not less than 0.9, Service Value (CMM/W) minimum

6.85, Air delivery minimum 215 CMM, 350 RPM (tolerance as per

IS : 374-2019), THD less than 10%, remote or electronic regulator

unit for speed control and all remaining accessories including safety

pin, nut bolts, washers, temperature rise=75 degree C (max.),

insulation resistance more than 2 mega ohm, suitable for 230 V, 50

Hz, single phase AC Supply, earthing etc. complete as required.

10.18 (CIVIL) Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box

for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid

of 1.5 mm thick M.S. sheet with its top surface hacked for proper

bonding, top lid shall be screwed into the cast iron/ M.S. sheet box

by means of 3.3 mm dia round headed screws, one lock at the

corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape

as per standard drawing. 62 Each 185 11483

TOTAL COST (PART-A_DSR ITEM) 4,919,491

PART-B_NON DSR ITEM

1 Providing & Fixing of modular plate type white RJ 45 CAT 6 Data outlet /

information outlets in existing 1.0 mm tk G.I. Switch control boxes, with

cover plate, grid plate, screws, etc with connections as required.

a 1 nos. RJ 45 Data Outlet 3 NOS 331 993

Supplying, fixing, connecting, testing and commissioning of

following rating, ISI marked (IS 8828) 240 / 415 volts, 10 KA,

2 Miniature Circuit Breaker (MCB) of single / double / three / four poles in

the existing MCB DB or in existing MS enclosure complete in all respects.

a 40 Amp. DP MCB 5 NOS 962 4812

b 40 Amp. SP MCB 5 NOS 604 3018

c 63 Amp. DP MCB 2 NOS 1117 2234

d 63 Amp. SP MCB 2 NOS 699 1397

e 20 Amp. TP MCB 2 NOS 1122 2243

f 40 Amp. FP MCB 9 NOS 1979 17814

g 40 Amp. TP MCB 9 NOS 1612 14507

3 Design, manufacture, supply, testing , installation and commissioning

of CLUB Panel fabricated out of 14 SWG CRCA sheet steel, IP 42, wall /

floor mounting type. The sheet steel shall undergo minimum 9 tank

treatment followed by finishing powder coating of min 60 micron thickness.

the board includes 415 V electrolitic Aluminium Bus Bar, removable gland

plates, cable glands, including connection with outgoing feeders complete

in all respect.

The incoming MCCB shall be microprocessor based with inbuilt O/L & S/C

release with inbuilt E/F protection and all Outgoings MCCB's shall be

thermal-magnetic based with inbuilt O/L & S/C release.

All MCCB's shall be Ics = 100% Icu, with rotary handle & pad locking

arrangement, with adjustable O/L & S/C trip setting as per load

requirement. All TP MCCB shall be with solid isolable neutral link. The

breaking capacity specified is Ics value. All outgoing MCB's shall be C type

with 15 KA breaking capacity.

Mix & Match famlies / makes of MCCB's / MCB's shall not be allowed, They

are all of same manufacturer.

The fault withstanding capacity of panel shall be 15 KA rms for 1 sec.

The above board shall be complete with 3 nos. phase indicating lights, flush

mounted Ammeter, Voltmeter, CT's, PT's, selector switches, protective

fuses etc. at Incomer with all inter connections by min. 2.5 sq.mm. Copper

INCOMER : 630 AMP FP MCCB (25 KA)

BUS BAR : 630 AMP, 500 Volts, 3 phase 50 HZ TPN high conductivity

electrolytic Aluminium bus bar with conductivity of min 57 to 58% of

suitable length, insulated by heat shrinkable sleeves. The current density of

bus bar shall be minimum 1.00 sq mm / amp.

The Maximum allowable temperature for the Bus bar to be restricted to 85

deg C. The temperature rise should be restricted to 35 deg C above ambient

2 no 315 AMP TP MCCB (25 KA)

1 no 250 AMP TP MCCB (25 KA)

5 no100 AMP TP MCCB (25 KA)

4 no 40 AMP TP MCCB (25 KA)

4 no 40 AMP TP MPCB (25 KA) 1 SET 450481 450481

SUPPLY AND LAYING OF CABLES & ACCESSORIES

4 Supply of ISI marked aluminium conductor XLPE insulated cable as per

IS 7098,Al. armoured, served, sheathed 1100 volts grade.

5 Supply of 1000V grade bare copper conductor XLPE low smoke halogen

free insulated with fire rated glass mica tape LSZH inner and outer

sheathed armored fire survival cable, having fire resistance and all other

parameters conforming to IS-17505. (For Elevator ).

6 Laying and testing of aluminium / copper conductor cable PVC / XLPE

insulated armoured, served, sheathed 1100 volts grade. On surface the

cable run shall be fixed by GI clamps etc. of suitable size or on existing

cable tray or inside existing RCC / HDPE DWC pipe complete in all

respect .The armouring of the cable shall be properly connected with the

earth conductor including fixing of palm or pin type copper tin plated cable

socket (lug) / end terminations to the cable leads, insulating with tape and

making connections with brass / nickle plated flame proof double

compression glands, providing cable tags complete in all respect upto the

satisfaction of Engineer-in-charge. (The supply of terminations and glands

shall be under seperate item)

7 Supply fixing of plam type heavy duty Copper cable socket (lug) (for

Fire Survival Cable) to the cable leads, insulating with tape and

making connections etc. complete in all respects as per direction of

Engineer-in-charge.

8 Supply and fixing brass nickle plated flame proof double compression

glands for PVC / XLPE insulated armoured, served, sheathed cable

including rubber ring etc. complete in all respect. The armouring of the

cable shall be properly connected with the earth conductor.

6 sqmm 4 core 6 NOS 474 2845

9 Providing & fixing 32mm x 6mm G.I. strip on surface, in recess or in

ground including connections etc. as required.

10 Maintenance Free Earthing : - Supply of Low carbon high tensile Copper

Bonded Ground rods having min 250 micron of copper coating . The

diameter of Rod should be 17.2 mm with the length of 3000 mm . The

ground rod should be UL approved and tested from CPRI. The earthing

include 400 mm square C.I. frame with hinged cover, masonry housing

including excavation and back filling.

The Rod should be surrounded with Earth Enhance compound of 25 Kg

tested as per IEC 62561-2 for the rod & IEC 62561 -7 for compound. (borh

are from same manufacturer)

Exothermic welding shall be used for connection between main electrode

(copper bonded rod) and copper strip of size 32 x 6 mm. Further GI strips

from equipments shall be connected to Copper strips by means of special bi-

matellic connector (i.e. stainless steel). please refer submitted drawing.

11 Installation of Maintenance free earthing , as per specification ,including all

the required work in supervision of site engineer.

Supply of AC 230/250 volts, 50 HZ exhaust fans including providing

12 nuts, bolts, mounting frame and other accessories etc. complete

a 450 mm sweep 900 rpm (BEE 5 Star) 12 Nos 7094 85133

13 Supply of 400mm circular Suspended 25w energy saving, environmental

friendly, long life, decorative, corrosion resistant, surface-suspended

luminaires with PS diffuser and extruded aluminium housing with LEDs as

light source Aluminum extrusion heat sink for effective thermal

management, sturdiness and excellent corrosion resistant fitted in white

finish covered with high efficiency long life SMD LED module is mounted on

FR4 with lumen efficacy of >140 lm/W to enhance the lumen output: 2300

with system efficacy : 90 Lm/W. PS diffuser in opal finish for glare free

uniform light distribution which was powered by a built-in isolated low THD

electronic LED driver (SMPS based constant current supply) with output

short circuit protection, surge protection with 2.5kv & other safety tests as

per IS: 15885 Part 2/ Sec 13 Operating temperature :- 10 °C to +45 °C &

Operating voltage range : 140 V - 270 V Average life L70B50: 50000 hours

with IP20 with power factor PF: 0.90 CCT : 4000k CRI: ≥80 this should be

with BIS & NABL certified with LM79 & LM80 Reports.

14 Supply of 25w 4 feet suspended with aluminum extruded housing in white

powder coated finish and plastic (ABS) end caps and High transmittance

PMMA opal diffuser for glare free symmetric light distribution. along with

high efficiency long life LED package in integral module with lumen efficacy

> 135 lm/W With Systems Lumens of 2750 Lumens with system efficacy of

115 LM/W and viewing angle of 120° to ensure better uniformity. Powered

by a built-in isolated low THD :≤10 electronic LED driver ( SMPS based

constant current supply) with output short circuit protection, surge

protection with 2.5kv & other reliability tests as per IS: 15885 Part 2/ Sec

13. Operating temperature :- 10 °C to +45 °C & Operating voltage range :

140 V - 270 V Average life L70B50: 50000 hours with IP20 with power

factor PF: 0.90 CCT : 4000k CRI: ≥80 this should be with BIS & NABL

certified with LM79 & LM80 Reports.

15 Supply of 600mm circular Suspended 36w energy saving, environmental

friendly, long life, decorative, corrosion resistant, surface-suspended

luminaires with PS diffuser and extruded aluminium housing with LEDs as

light source Aluminum extrusion heat sink for effective thermal

management, sturdiness and excellent corrosion resistant fitted in white

finish covered with high efficiency long life SMD LED module is mounted on

FR4 with lumen efficacy of >140 lm/W to enhance the lumen output: 3400

with system efficacy : 90 Lm/W. PS diffuser in opal finish for glare free

uniform light distribution which was powered by a built-in isolated low THD

electronic LED driver (SMPS based constant current supply) with output

short circuit protection, surge protection with 2.5kv & other safety tests as

per IS: 15885 Part 2/ Sec 13 Operating temperature :- 10 °C to +45 °C &

Operating voltage range : 140 V - 270 V Average life L70B50: 50000 hours

with IP20 with power factor PF: 0.90 CCT : 4000k CRI: ≥80 this should be

with BIS & NABL certified with LM79 & LM80 Reports.

16 Supply of Surface/ Suspended 80W Low Bay made up of White powder

coated, elegantly designed Pressure die-cast aluminium ring and shot

ballasting heat sink for efficient heat dissipation, High efficiency long life

Discrete LED mounted on MCPCB. Lumen efficacy of LED >150 lm/W with

viewing angle 120º to ensure better uniformity of light distribution. High

efficiency polycarbonate UV stabilize cover with integrated lens to ensure

symmetric light distribution ( for detail photometric data please refer LM79

report & IES). Powered by built-in, isolated, electronic LED driver (SMPS

based constant current supply) with Output Short-circuit protection, Surge

Voltage protection & other safety,test as per IS:15885 Part 2/Sec 13 and

CISPR. Corelated Color temperature(CCT): 5700K, IP 54, IP: 65, IK 07,

Operating temperature: -10 °C to +45 °C, Operating voltage range: 140 V -

270 V, Average life L70B50: 50000 hours THD<10%, LED Driver: Potted

Driver, Surge protection > 3 KVA, Fixture Lumen Efficacy > 135Lm/W,

Fixture Lumen>6200, Color Rendering Index (CRI)> 80, With dia of 166MM.

Havells Cat Ref: Iliosbay

17 Supply of 25w with 36degree Circluar recessed snoot light (Wall Washer)

Off-White powder coated, elegantly designed

pressure die-cast aluminium housing / heat sink for efficient heat dissipation

& White PC ring for

holding the diffuser and High efficiency long life COB LED mounted on

MCPCB. Lumen efficacy of LED >90 lm/W with viewing angle 120º to

ensure better uniformity of light distribution with High purity faceted

aluminum glossy reflector. to enhance the lumen output @ 2375 Lumens

with High quality PC Diffuser for uniform light distribution. Powered by an

independent, isolated, SELV

output electronic LED driver (SMPS based constant current supply) with

Output Short-circuit protection, Surge Voltage protection & other safety test

as per IS:15885 Part 2/Sec 13.

18 Supply of LED 25W decorative, 400MM Dia, corrosion resistant, surface-

suspended luminaire.Housing in Aluminum extrusion heat sink for effective

thermal management, sturdiness and excellent corrosion resistant fitted in

white finish.High transmittance PS diffuser in opal finish for glare free

uniform light distribution.High efficiency long life SMD LED module is

mounted on FR4 with lumen efficacy of >140lm/W to enhance the lumen

output.Powered by an integral isolated low THD electronic LED driver (

SMPS based constant current supply) with output short circuit protection,

surge protection. Lumen Output of 2180 lumens.CRI >80, Color

temperature 4000K, THD <10% and PF >0.90,IP20,IK03.Life class of

50,000 hrs @ L70, Operating Temperature:-10 TO +45 DEG.C; Input

Supply Voltage Range:140-270 V, Frequency :50-60 HZ; Internal Surge

Protection:3 KV; Protection : Reverse Polarity, Open & Short Circuit.

DRIVER SAFETY REQUIREMENT STANDARDS :IS 15885-2-13, TEST

REPORT TO BE SUBMITTED; PHOTO BIOLOGICAL SAFETY NORMS:

IS 16108, TEST CERTIFICATE TO BE SUBMITTED; CERTIFICATION:

LM 79 FOR LUMINAIRE LM 80 FOR LED SOURCE. Havels Cat Ref:

19 Supply of 18W LED Surface mounted downlighter with nominal system

lumen output of 1800lm and a minimum system efficacy of 100lm/W.

Surface mounted Downlight with Aluminium (99% Purity) Sink, available in

Round shape. PC diffuser in white powder coated finish with built in

electronic low THD (<10%) LED driver.The LED chips are mounted in Metal

core printed circuit board with thermal paste for better heat dissipation.The

luminaire shall have a rated system life of 50,000BH @ L70 and other

standard accessories. complete in all aspects and as directed by Electrical-

In-Charge.. The luminaire shall have Aluminium housing in White PC

finish.The luminare should have beam angle of 90Deg with a color

temperature of 5700K and CRI>80. The luminaire shall meet IP20 rating

with high quality polycarbonate frosted diffuser for glare-free uniform light

distribution and the diffuser helps to stabilise UV and prevent from yellowing

and the luminaire has the features of Input Voltage : AC220-240V, 50/60Hz,

Voltage operating range : 90-295V with, High Surge Protection : 2.5KV. The

luminaire shall have operating temperature of (-10) Deg C to 45 Deg C.

(Model- INTEGRANXTRDDLRSURD18WLED857S)

20 Supply of recessed mounted 15W Round Shape Downlighter with high

performance LEDs, suitable for mounting with Armstrong/Grid ceiling.

pressure die-cast aluminium heat sink & PC diffuser in white powder coated

finish with integral electronic low THD (<10%) LED driver.High efficiency

long life LED package in integral module with lumen efficacy of >110 lm/W

.Powered by an integrated driver, SELV Output electronic LED driver

(SMPS based constant current supply) with Output Short-circuit protection,

Surge protection & other reliability test. CRI >80, Color temperature 5700K,

THD <10% a,PF >0.95,IP20,IK03.Life class of 50,000 hrs @ L70,

Operating Temperature:-10 TO +45 DEG.C; Input Supply Voltage

Range:140-270 V, Frequency :50-60 HZ; Internal Surge Protection:3.5 KV;

Protection : Reverse Polarity, Open & Short Circuit. DRIVER SAFETY

REQUIREMENT STANDARDS :IS 15885-2-13, TEST REPORT TO BE

SUBMITTED; PHOTO BIOLOGICAL SAFETY NORMS: IS 16108, TEST

CERTIFICATE TO BE SUBMITTED; CERTIFICATION: LM 79 FOR

LUMINAIRE LM 80 FOR LED SOURCE. Havells Cat Ref:Havells

INTEGRA, Signify, LT

21 Supply of IP65, IK05, dust free & zero maintenance 2x2 LED Clean Room

Bottom Opening luminaire for hygenic facilities. 2x2 BOCR with walkable

tray @ 4000 Lumens with System Efficacy of 100lm/W of SDCM LEDs < 5

along with MS powder coated white after phosphochromate treatment

provided as standard with 60 Micron and High quality polycarbonate opal

diffuser with 1.5MM thickness for glare free uniform light distribution with

High efficiency 90% long life LED package in integral module with lumen

efficacy of >140 lm/ W and viewing angle of 120° to ensure better

uniformity.Powered by an independent, Isolated, SELV Output electronic

LED driver (SMPS based constant current supply) with Output Shortcircuit

protection, Surge protection with 3.5kv & other Safety test as per IS:15885

Part 2/Sec 13.CRI >80, Color temperature 5700K, THD <10% ,PF

>0.95.Life class of 50,000 hrs @ L70, Operating Temperature:-10 TO +45

DEG.C; Input Supply Voltage Range:140-270 V, Frequency :50-60 HZ; Anti

Bacterial with Paint Coated protection ISO 22196: 2011 and exhibited a

minimum of 95% and up to 99.99% reduction in the population of

Escherichia coli and Methicillin Resistant Staphylococcus aureus

(MRSA).Reverse Polarity, Open & Short Circuit, TEST REPORT TO BE

SUBMITTED; PHOTO BIOLOGICAL SAFETY NORMS: IS 16108, TEST

CERTIFICATE TO BE SUBMITTED; CERTIFICATION: LM 79 FOR

LUMINAIRE LM 80 FOR LED SOURCE. Havells Cat Ref:Havells

BOCR2X2R42WLED857SPCMSEXE or Equivalent

22 Supply of 12W Deep Recessed diffuser Ceiling Recess Mounted downlight

luminaires with housing, bottom ring and heat sink made of pressure die-

cast aluminium. Luminaire shall deliver excellent illumination & comfort with

CRI of >80, Deep-recessed opal diffuser for glare-free symmetric light

distribution. Luminaires should be with 100 lm/W System Efficacy and

designed Avg. LED Life (L70 B50) 50,000 Burning Hours & with high

efficient Photobiologically safe LEDs. Luminaire should be Powered by an

independent, isolated output electronic driver offering THD<10% , Output

Short-circuit protection, Surge Voltage protection, and other reliability tests

as per IS:15885 Part 2/Sec 13. Luminaires and Drivers to be manufactured

by the same OEM having an in-house NABL-accredited Laboratory for

testing Photometric parameters.

23 Supply of 40W Energy saving, environmental friendly, long life, corrosion

resistant, impact proof, surface mounting IK07, IP66 luminaire with System

Lumen Output 4200 lm. Housing is made up of scratch resistant

unbreakable polycarbonate in grey finish. PG 16x1.5 cable gland is used for

maintaining ingress protection. The luminaire shall have High efficiency long

life LED package in integral module with lumen efficacy of >140 lm/W and

viewing angle of 120° to ensure better uniformity. The fixture shall have High

quality polycarbonate diffuser in opal finish for glare free uniform light

distribution, clip fitted to the housing. The luminaire shall have With power

coated CRCA sheet acts as reflector and control gear trey.The luminaire

shall be Powered by a built-in isolated low THD electronic driver (SMPS

based constant current supply) with low THD, Output Short-circuit / Open

Circuit protection, Surge protection & Safety test as per IS:15885 Part

2/Sec 13. The luminaire shall have Operating temperature: -10 °C to +45

°C, Operating voltage range: 140 V - 270 V, Average life L70B50: 50000

hour. The luminaire shall have Power Factor>=0.95 & THD <=10, CCT

4000 K & CRI>=80. Havells Havells Magnum Grand Neo, LT, Signify

24 Supply of 10W LED batten luminaires with housing made of Aluminum

Extrusion for thermal management with an anodized finish. Battens should

be suitable for Wall/Ceiling mounting with SS clamp. Luminaire shall deliver

excellent illumination & visual comfort with CRI of >80, High transmittance

Opal Polycarbonate diffuser for glare-free symmetric light distribution.

Luminaires should be with 100 lm/W System Efficacy and designed for

Avg. LED Life (L70 B50) 50,000 Burning Hours & with high efficient

Photobiologically safe LEDs. Luminaire should be Powered by an integral

electronic constant current driver offering THDi<10% , Output Short-circuit

protection, Surge Voltage protection, and other reliability tests as per

IS:15885 Part 2/Sec 13. Luminaires should be provided with 4kV surge

protection. Luminaires manufacturer to have an in-house NABL-accredited

Laboratory for testing Photometric parameters

25 Supply of Track Mounted 25W LED light with Modern design,compact Size

with High power COB LED to provide focussed light. Track light is a method

of lighting where light fixtures are attached anywhere on a continuous track

rail which is electrically charged as compared to the need of routing

electrical wiring to individual light position made of Pressure Die-cast

aluminium housing (heat sink)with powder coated White finish. PC diffuser

in clear finish for glare free uniform light distribution along with Aluminum

reflector to enhance the lumen output of the fixture. Operating voltage range-

140 V - 270 V, Operating temperature: ta 35 °C, Average life L70B50:

50000 hours, IP 20, THD<15%, PF>0.95, Powered by a Built-in isolated

electronic LED driver in PC housing with Output Short Circuit protection,

Over Voltage protection, Surge oltage protection and other safety test as per

IS:15885 Part 2/Sec 13. CCT 3000K/4000K, System Eficacy>80Lm/W,

System Lumen 2000 Lm, Beam angle 24/38 Deg, CRI>80. DRIVER

SAFETY REQUIREMENT STANDARDS :IS 15885-2-13, TEST REPORT

TO BE SUBMITTED; DRIVER PERFORMANCE REQUIREMENTS: IS

16104, TEST REPORT TO BE SUBMITTED; PHOTO BIOLOGICAL

SAFETY NORMS: IS 16108, TEST CERTIFICATE TO BE SUBMITTED;

CERTIFICATION: LM 79 FOR LUMINAIRE LM 80 FOR LED SOURCE.

Cat Ref: Havells Uneco. Suitable for 1m and 2m Track to be bought

26 Supply of 12w 2 feet suspended with aluminum extruded housing in white

powder coated finish and plastic (ABS) end caps and High transmittance

PMMA opal diffuser for glare free symmetric light distribution. along with

high efficiency long life LED package in integral module with lumen efficacy

> 135 lm/W With Systems Lumens of 1200 Lumens with system efficacy of

100 LM/W and viewing angle of 120° to ensure better uniformity. Powered

by a built-in isolated low THD :≤10 electronic LED driver ( SMPS based

constant current supply) with output short circuit protection, surge

protection & other reliability tests as per IS: 15885 Part 2/ Sec 13.

Operating temperature :- 10 °C to +45 °C & Operating voltage range : 140 V

- 270 V Average life L70B50: 50000 hours with IP20 with power factor PF:

0.90 CCT : 5700k CRI: ≥80 this should be with BIS & NABL certified with

LM79 & LM80 Reports.

27 Supply of 20W LED batten luminaires with housing made of Aluminum

Extrusion for thermal management with an anodized finish. Battens should

be suitable for Wall/Ceiling mounting with SS clamp. Luminaire shall deliver

excellent illumination & visual comfort with CRI of >80, High transmittance

Opal Polycarbonate diffuser for glare-free symmetric light distribution.

Luminaires should be with 100 lm/W System Efficacy and designed for

Avg. LED Life (L70 B50) 50,000 Burning Hours & with high efficient

Photobiologically safe LEDs. Luminaire should be Powered by an integral

electronic constant current driver offering THDi<10% , Output Short-circuit

protection, Surge Voltage protection, and other reliability tests as per

IS:15885 Part 2/Sec 13. Luminaires should be provided with 4kV surge

protection. Luminaires manufacturer to have an in-house NABL-accredited

Laboratory for testing Photometric parameters

28 Supply of half moon 36w 4 feet suspended with aluminum extruded housing

in grey powder coated finish and screwless ABS end covers covered High

transmittance special profiled opal PC diffuser for glare free symmetric light

distribution also High efficiency long life LED package in integral module

with lumen efficacy >120 lm/W and viewing angle of 120 degree to ensure

better uniformity. Systems Lumens of 3050 Lumens with system efficacy of

85 LM/W and viewing angle of 120° to ensure better uniformity.Powered by

Buit-In, Isolated low THD electronic LED driver ( SMPS based constant

current supply) with output short circuit protection, surge protection of 2.5Kv

& other reliability tests as per IS: 15885 Part 2/ Sec 13.. Operating

temperature :- 10 °C to +45 °C & Operating voltage range : 140 V - 270 V

Average life L70B50: 50000 hours with IP20 ,IK03 with power factor PF:

0.90 CCT : 5700k CRI: ≥80 this should be with BIS & NABL certified with

LM79 & LM80 Reports.

29 Supply of X Shape, 48w Surface/Suspended Downlight, linear 4ft

luminaire(50mm width) made of Aluminum extruded housing in white

powder coated finish and plastic moulded end caps. High transmittance

PMMA opal diffuser . High efficiency long life LED package in integral

module with lumen efficacy > 110 Lm/W and viewing angle of 120° to

ensure better uniformity. Powered by an integral isolated low THD electronic

LED driver ( SMPS based constant current supply) with output short circuit

protection, surge protection. Lumen Output of 5900 lumens. CRI >80, Color

temperature 5700K, THD <10% and PF >0.90,IP20,IK03.Life class of

50,000 hrs @ L70, Operating Temperature:-10 TO +45 DEG.C; Input

Supply Voltage Range:140-270 V, Frequency :50-60 HZ; EMI/EMC

Compliance Internal Surge Protection:3 KV; Protection : Reverse Polarity,

Open & Short Circuit. DRIVER SAFETY REQUIREMENT STANDARDS

:IS 15885-2-13, TEST REPORT TO BE SUBMITTED; PHOTO

BIOLOGICAL SAFETY NORMS: IS 16108, TEST CERTIFICATE TO BE

SUBMITTED; CERTIFICATION: LM 79 FOR LUMINAIRE LM 80 FOR LED

SOURCE. Cat Ref: DESTELLO

30 Supply of Y Shape, 36w Surface/Suspended Downlight, linear 4ft

luminaire(50mm width) made of Aluminum extruded housing in white

powder coated finish and plastic moulded end caps. High transmittance

PMMA opal diffuser . High efficiency long life LED package in integral

module with lumen efficacy > 110 Lm/W and viewing angle of 120° to

ensure better uniformity. Powered by an integral isolated low THD electronic

LED driver ( SMPS based constant current supply) with output short circuit

protection, surge protection. Lumen Output of 5900 lumens. CRI >80, Color

temperature 5700K, THD <10% and PF >0.90,IP20,IK03.Life class of

50,000 hrs @ L70, Operating Temperature:-10 TO +45 DEG.C; Input

Supply Voltage Range:140-270 V, Frequency :50-60 HZ; EMI/EMC

Compliance Internal Surge Protection:3 KV; Protection : Reverse Polarity,

Open & Short Circuit. DRIVER SAFETY REQUIREMENT STANDARDS

:IS 15885-2-13, TEST REPORT TO BE SUBMITTED; PHOTO

BIOLOGICAL SAFETY NORMS: IS 16108, TEST CERTIFICATE TO BE

SUBMITTED; CERTIFICATION: LM 79 FOR LUMINAIRE LM 80 FOR LED

SOURCE. Cat Ref: DESTELLO

31 ERECTION OF LIGHTING FIXTURES

Recess / surface, round / square, ceiling mounting LED Light fixture 1,019 NOS 150 152850

TOTAL COST (PART-B_NON DSR ITEM) 7,228,654

GRAND TOTAL COST (PART-A+PART-B) 12,148,145

GRAND TOTAL COST (PART-A+PART-B) 12,148,145

SCHEDULE OF QUANTITIES FOR INTERNAL PLUMBING WORKS

PROJECT: COMMUNITY CENTRE, HEART BEAT CITY-2, NOIDA.

PART A (SCHEDULED ITEMS AS PER D.S.R. - 2021)

SNo DESCRIPTION QTY

D.S.R. RATE AMOUNT

No. UNIT (Rs.) (Rs.)

A SANITARY FIXTURES & ACCESSORIES

1 Providing and fixing white vitreous china extended wall

mounting water closet of size 780x370x690 mm of approved

shape including providing & fixing white vitreous china cistern

with dual flush fitting, of flushing capacity 3 litre/ 6 litre 17.78 28 Each 13036.54 365,023.02

(adjustable to 4 litre/ 8 litres), including seat cover, and cistern

fittings, nuts, bolts and gasket etc complete.

Providing and fixing white vitreous china flat back half stall

urinal of size 580x380x350 mm with white PVC automatic

flushing cistern, with fittings, standard size C.P. brass flush pipe,

spreaders with unions and clamps (all in C.P. brass) with waste

fitting as per IS : 2556, C.I. trap with outlet grating and other

couplings in C.P. brass, including painting of fittings and cutting

and making good the walls and floors wherever required :

Single half stall urinal with 5 litre P.V.C. automatic flushing

Providing and fixing wash basin with C.I. brackets, 15 mm C.P.

brass pillar taps, 32 mm C.P. brass waste of standard pattern,

including painting of fittings and brackets, cutting and making

good the walls wherever require: 17.7

White Vitreous China Wash basin size 630x450 mm with a single

15 mm C.P. brass pillar tap

Providing & fixing stainless steel A ISI 304 (18/8) kitchen sink as

per IS :13983 with C.I. brackets and stainless steel plug 40 mm,

including painting of fittings and brackets, cutting and making

good the walls wherever required. 17.10

Kitchen sink with drain board. 17.10.1

Providing and fixing CP Brass 32mm size Bottle Trap of approved

quality & make and as per the direction of Engineer-in-charge.

Providing and fixing CP Brass Single lever telephonic wall mixer

of quality & make as approved by Engineer in charge.

(a) 15 mm nominal dia 17.22B 6 Each 6119.17 36,715.02

7 Providing and fixing P.V.C. waste pipe for sink or wash basin

including P.V.C. waste fittings complete 17.28

Flexible pipe 17.28.2

8 Providing and fixing 600x450 mm beveled edge mirror of

superior glass (of approved quality) complete with 6 mm thick

hard board ground fixed to wooden cleats with C.P. brass screws

and washers complete

9 Providing and fixing toilet paper holder : 17.34

B WATER SUPPLY PIPES AND FITTINGS

1 Providing, fixing chlorinated polyvinyl Chloride (CPVC) pipes,

having thermal stability for hot and cold water supply including

all CPVC plain and brass threaded fittings including fixing the

pipes with clamps at 1.00 m spacing. This includes jointing of

pipes & fittings with one step CPVC solvent cement and testing

of joints complete as per direction of Engineer in charge.

Internal work-exposed on wall

32mm nominal outer dia pipes 18.7.4 10 R.M. 500.97 5,009.70

40mm nominal outer dia pipes 18.7.5 5 R.M. 674.36 3,371.80

50mm nominal outer dia pipes 18.7.6 5 R.M. 927.00 4,635.00

2 Providing, fixing chlorinated polyvinyl Chloride (CPVC) pipes,

having thermal stability for hot and cold water supply including

all CPVC plain and brass threaded fittings including fixing the

pipes with clamps at 1.00 m spacing. This includes jointing of

pipes & fittings with one step CPVC solvent cement and the cost

of cutting chases and making good the same including testing of

joints complete as per direction of Engineer in charge.

Concealed work including cutting chase and making good the

15mm nominal outer dia pipes 18.8.1 280 R.M. 441.15 123,522.00

20mm nominal outer dia pipes 18.8.2 160 R.M. 513.73 82,196.80

25mm nominal outer dia pipes 18.8.3 20 R.M. 626.05 12,521.00

32mm nominal outer dia pipes 18.8.4 25 R.M. 712.75 17,818.75

3 Providing, fixing G. I. pipes complete with G. I. fittings and

clamps including cutting and making good the walls etc.

Internal work-exposed on wall

25mm dia nominal bore 18.10.3 20 R.M. 491.18 9,823.60

32mm dia nominal bore 18.10.4 20 R.M. 563.58 11,271.60

4 Painting G. I. pipes and fittings with synthetic enamel white

paint with two coats over a ready mixed priming coat, both of

approved quality for new work.

25mm dia nominal bore 18.38.3 20 R.M. 25.64 512.80

32mm dia nominal bore 18.38.4 20 R.M. 30.75 615.00

5 Providing and fixing G.I. Union in G.I. pipe including cutting and

threading the pipe and making long screws etc. complete (New

32mm dia nominal bore 18.46.4 5 R.M. 409.47 2,047.35

40mm dia nominal bore 18.46.5 5 R.M. 523.20 2,616.00

6 Providing and fixing gun metal gate valve with C.I. wheel of

approved quality (screwed end) :

32 mm nominal bore 18.17.2 2 Each 589.91 1,179.82

7 Providing & fixing unplasticised PVC connection pipe with

45 cm length 18.21.2 -

15 mm nominal bore 18.21.2.1 70 Each 85.18 5,962.60

8 Providing and fixing C.P. brass shower rose with 15 or 20 mm

9 Providing & fixing CP brass bib cock of approved quality

conforming to IS: 8931.

15 mm nominal bore 18.49.1 5 Each 434.20 2,171.00

10 Providing and fixing C.P brass long Nose bib cock of approved

quality conforming to IS standards and weighing not less than

15 mm nominal bore 18.50.1 2 Each 715.06 1,430.12

11 Providing & fixing 15 mm nominal bore C.P brass angle valve for

basin mixer and geyser points of approved quality conforming

12 Providing and fixing C.P. Brass extension nipple (size

of approved make and quality as per direction of Engineer-in-

C RAIN WATER PIPES AND FITTINGS - (Rigid PVC)

Providing and fixing on wall face unplasticised - Rigid PVC rain

water pipes conforming to IS : 13592 Type A including jointing

with seal ring conforming to IS : 5382 leaving 10 mm gap for

thermal expansion, (i) Single socketed pipes

2 Providing and fixing on wall face unplasticised - PVC moulded

fittings / accessories for unplasticised - Rigid PVC rain water

pipes conforming to IS : 13592 Type A,including jointing with

seal ring conforming to IS : 5382 leaving 10 mm gap for thermal

Coupler 12.42.1

Single pushfit Coupler 12.42.2

Single Tee without door 12.42.4

3 Providing and fixing unplasticised - PVC pipe clips of approved

design to unplasticised - PVC rain water pipes by means of

50x50x50 mm hard wood plug screwed with MS screws of

required length including cutting brick work and fixing in cement

mortar 1:4 (1 cement : 4 coarse sand) and making good the wall

4 Providing and fixing to the inlet mouth of rain water pipe cast

iron grating 15 cm diameter and weighing not less than 440

TOTAL SCHEDULED ITEM COST 1,167,797.00

PART B (NON SCHEDULED ITEMS - AS PER MARKET RATES)

A WATER SUPPLY PIPES AND FITTINGS

Providing & Fixing of C.P. Brass health faucet for ablution with 1

1 meter long CP tube, hand shower, couplings, wall hook and MR-1 28 Each 1,101.00 30,828.00

other accessories, complete in all respect.

2 Providing, fixing and testing in position ISI marked (IS : 1239) G.I

pipes (medium class) in exposed works complete with all

necessary G.I fittings i.e. sockets, elbows, tees, bends, unions,

plugs and clamps. (on terrace the pipes shall be supported at

suitable interval and inside ducts these shall be properly

clamped through duct walls by G.I. U clamp / bracket). The

Galvanization shall conform to IS : 4736. The work shall include

the painting with two coats enamel paint of approved quality

and shade over a coat of primer on exposed pipe works

including providing grooved fittings wherever pipe crosses exp

joint, complete as required by the Engg-in-charge for proper

completion of the work. (The price excludes breaking and

making good the walls / floor)

(Make : Jindal (Hissar) / Prakash Surya/ Tata)

65mm nominal bore (wall thickness - 3.6 mm) MR-2 5 R.M. 1,317.01 6,585.05

80mm nominal bore (wall thickness - 4.0 mm) MR-3 5 R.M. 1,586.44 7,932.20

3 Supply & fixing in position ISI marked cast iron Wafer type

butterfly valves (PN 16) as per IS:13095, with SS disc, SS shaft,

SS seating rings, SS internal fastening, EPDM seat, CS external

nuts-bolts including transporting to worksite etc. including

testing, Complete as per drawings & directions of the Engineer-

4 Providing and fixing C I body flanged strainer fabricated out of

1.6 mm thick Stainless Steel 304 sheet having 0.6 mm to 0.8 mm

dia perforations complete.

5 Supply & fixing in position cast iron / ductile iron body dual

plate wafer type check valve (NRV) (PN 16) with SS disc, SS

stem, EPDM seat, spring & pin, SS stem, SS internal fastening, CS

external fastening, including transportation to worksite, supply

& fixing complete with testing as per direction of the Engineer -

6 Providing, fixing, jointing and testing in position UPVC sch 80

pipes with sch 80 fittings, Lead Free, UV stabilized, confirming to

ASTM D 1785 & ASTM D 2467 suitable for cold water supply in

exposed / suspended works complete with all necessary fittings

i.e. elbows, tees, bends, couplers, reducers, unions, plugs,

transition fittings, clamps including jointing the pipe and fitings

by solvent cement over primer coat as per ASTM D 2564

including proper support and clamped complete as required. (on

terrace / basement the pipes shall be supported at suitable

interval and inside ducts these shall be properly clamped

through duct walls by rubber lined G.I. U strap clamp / bracket)

on 40x40x3 mm G.I slotted angle included threaded fittings with

or without brass inserts including building expansion loop

wherever pipe crosses expansion joint, as required by the Engg-

in-charge for proper completion of the work.

15 mm Nominal Size / 21.34 mm OD (min. wall tk - 3.73 mm) 182.00

20 mm Nominal Size / 26.67 mm OD (min. wall tk -3.91 mm) 213.00

25 mm Nominal Size / 33.40 mm OD (min. wall tk - 4.55 mm) 267.00

32 mm Nominal Size / 42.16 mm OD (min. wall tk - 4.85 mm) 315.00

40 mm Nominal Size / 48.26 mm OD (min. wall tk -5.08 mm) 364.00

50 mm Nominal Size / 60.32 mm OD (min. wall tk - 5.54 mm) 466.00

65 mm Nominal Size / 73.02 mm OD (min wall tk - 7.01 mm) 670.00

80 mm Nominal Size / 88.90 mm OD (min wall tk - 7.62 mm) 863.00

7 Providing, fixing, jointing and testing in position UPVC sch 40

pipes with sch 80 fittings, Lead Free, UV stabilized, confirming to

ASTM D 1785 & ASTM D 2467 suitable for cold water supply in

concealed works complete with all necessary fittings i.e.

elbows, tees, bends, couplers, reducers, unions, plugs, transition

fittings, clamps including jointing the pipe and fitings by solvent

cement over primer coat as per ASTM D 2564 including proper

support and clamped complete as required by the Engg-in-

charge for proper completion of the work. All termination points

for installation of faucets shall have brass terminal fittings. (The

price includes cutting chases and making good the walls)

15 mm Nominal Size / 21.34 mm OD (min. wall tk - 2.77 mm) 164.00

20 mm Nominal Size / 26.67 mm OD (min. wall tk - 2.87 mm) 176.00

25 mm Nominal Size / 33.40 mm OD (min. wall tk - 3.38 mm) 216.00

32 mm Nominal Size / 42.16 mm OD (min. wall tk - 3.56 mm) 267.00

8 Providing & fixing of hand lever operated uPVC (Sch 80) ball

valve type isolating valve including solvent welded joint as

15 mm nominal bore MR-23 31 Each. 222.00 6,882.00

20 mm nominal bore MR-24 53 Each. 266.00 14,098.00

25 mm nominal bore MR-25 6 Each. 381.00 2,286.00

32 mm nominal bore MR-26 5 Each. 458.00 2,290.00

40 mm nominal bore MR-27 5 Each. 633.00 3,165.00

50 mm nominal bore MR-28 2 Each. 883.00 1,766.00

65 mm nominal bore MR-29 1 Each. 3457.00 3,457.00

80 mm nominal bore MR-30 1 Each. 5051.00 5,051.00

9 Providing and fixing of cast iron Manhole Cover with frame for

overhead / underground water storage tanks. The fixing of

frame shall be done during the casting of the RCC slab of the

Providing and fixing in position M.S. / G.I. pipe flanged /

threaded sleeves of upto 600 mm long (heavy class) with M.S.

puddle flange fabricated out of 6 mm thick MS plate in RCC walls

of water tanks / retaining walls during the time of casting the

same including hot dipped galvanization after fabrication and

painting with two coats of anti corrosive paint over primer.

B SOIL , WASTE & VENT PIPES AND FITTINGS - SWR

1 Providing, fixing, jointing and testing in position of ISI marked

UV stabilized UPVC pipes for soil, waste, and vent, Type-B as

per IS : 13592 suitable for rubber ring joints for vertical pipes

and solvent cement joints for horizontal pipes, including all

neccessary specials and fittings (confirming to IS:14735) i.e.

bends, tees, junctions (with or without doors), reducers, WC

connectors, couplers, cowels, clamps, long radius / swept bend

at bottom of pipe, (All connections from horizontal to vertical

stacks must be through swept type fitting) hangers, rubber rings,

clean outs, C P Grating for any waste connection from washing

machine etc. fixing at wall / ceiling / floor level supported by

clamp & hangers etc. inside duct / suspended from floor under

false ceiling for proper completion of the work. The rubber ring

shall confirm to IS:5382.

The Pipes will be supported by either G.I. U strap clamps on

40x40x3 mm G.I. slotted angle duly painted (for a group of

pipes) or G.I. rubber lined split clamp (for independent pipes).

The cost will include all support arrangements. The work

includes cutting holes in wall/ floors/ slabs and making good the

same with cement concrete 1:2:4 complete as required. The

work includes commissioning of all pipes lines as per drawings

and specifications and as directed by engg-in-charge at site.

110 mm dia (Wall Thickness - 3.2 to 3.8 mm) MR-38 450 RM 574.00 258,300.00

75 mm dia (Wall Thickness - 3.2 to 3.8 mm) MR-37 50 RM 407.00 20,350.00

2 Providing & fixing UPVC Floor trap of self cleansing design with

CP Jali complete in all respects.

P-Trap type Floor Trap 110 x 110 mm (Long type - 50 mm seal) 317.00

Providing and fixing of drain point with 75 mm dia. Bend with CP

Jali complete in all respects.

Providing, fixing, jointing and testing in position ISI marked

(IS:4985) UPVC pipes of min 6 Kg/ Sq cm rating with fitting for

waste pipe from fixtures to floor trap including reduces,

enlarger, socket, couplers, bends, tees etc including fixing at

wall/ ceiling level supported by clamp & hangers etc. The work

includes cutting holes in wall/ floors/ slabs and making good the

same with cement concrete 1:2:4 complete as required.

E BOOSTER SYSTEM

Supply, installation, testing and commissioning of a set of MR-43

hydropneumatic Booster pump set for domestic water with

single VFD suitable for automatic operation and delivering the

specified discharge at the specified head. Each Pump shall be of

C.I base stainless steel SS 304 casing, SS 304 impeller and shaft

complete with gunmetal isolation valve on the suction line with

150mm dia pressure gauge, gunmetal non return valve and

gunmetal isolation valve on delivery line, complete with s/s

suction and delivery header piping of suitable size. The motor

shall be suitable for 415 ± 10% volts, 3 phase, 50 Hz A.C. power

supply. The set shall include Pump Mountedor Wall mounted an

automatic control panel with pressure sensor

transmitter,electrical wiring,cabling from panel to pumps and

FRP presssure tank with common base frame and complete

connecting accessories. The set shall be completely equipped

with variable fequency drive for automatic operation as per

load requirements and will run alternately in sequence in

cascade mode based on water demand. Note:Pumps should

be Eff > 3 HP >60% or BEE 4 star rated & Motors should

be Eff> 3 HP > 75% or BEE 4 star rated.

Domestic Booster System

One set of pumps- (1Working)

a) Water Flow Rate 3 LPS each MR-44 1 set 234,642.00 234,642.00

TOTAL ( NON-SCHEDULED ITEM ) 890,773.97

COST SUMMARY OF PLUMBING WORKS

TOTAL ( SCHEDULED ITEM ) 1,167,797.00

T O T A L ( NON SCHEDULED ITEMS ) 890,773.97

GRAND TOTAL (SCHEDULED + NON SCHEDULED ITEMS) 2,058,570.97

GRAND TOTAL (SCHEDULED + NON SCHEDULED ITEMS) 2,058,570.97

SCHEDULE OF QUANTITIES FOR FIRE FIGHTING WORKS - QUANTITY FOR INTERNAL ( CLUB )

PROJECT : HEART BEAT 2 HEARTBEAT CITY, PLOT NO. GH-01D, SECTOR-107, NOIDA

S.No DESCRIPTION TOTAL QTY UNIT AMOUNT (Rs.)

PART A (SCHEDULED ITEMS AS PER D.S.R. - 2019 (E&M))

1 Supplying, fixing, testing

and commissioning of

butterfly valve of PN 1.6

bronze/gunmetal seat

duly ISI marked complete

with nuts, bolts, washers,

gaskets conforming to IS

13095 of following sizes

2 Providing, installation,

commissioning of non-

return valve of following

sizes confirming to IS:

5312 complete with

rubber gasket, GI bolts,

nuts, washers etc.as

3 Providing, installation,

commissioning of

stainless steel Y-strainer

fabricated out of 1.6 mm

thick stainless steel,

Grade 304, sheet with 3

mm dia holes with

stainless steel flange.

4 Providing, laying, testing

& commissioning of 'C'

class heavy duty MS

pipe conforming to IS

3589 / IS 1239 including

Welding, fittings like

elbows, tees, flanges,

tapers, nuts bolts,

gaskets etc. and fixing

the pipe on the

wall/ceiling with suitable

clamp/support frame and

painting with two or more

coats of synthetic enamel

paint of required shade

complete as required :

5 Supplying and fixing

single headed internal

hydrant valve with

instantaneous Stainless

Steel coupling of 63 mm

dia with cast iron wheel

ISI marked conforming to

IS 5290 (Type -A) with

blank Gunmetal

/Stainless Steel cap and

chain as required :

6 Supplying and fixing first-

aid Hose Reel with MS

construction spray

painted in post office red,

conforming to IS 884

complete with the

following as required.

20 mm nominal internal

thermoplastic (Textile

reinforced) type -2 as per

20 mm nominal internal

dia gun metal globe valve

Drum and brackets for

fixing the equipmets on

Connections from riser

with 25 mm dia stop gun

valve & M.S. Pipe and

7 Supplying & fixing 63

mm dia Stainless Steel

(Grade 304)l short

branch pipe with 20 mm

nominal internal diameter

size nozzle conforming to

IS 903 suitable for

instantaneousconnection

to interconnect hose pipe

coupling as required

8 Supplying and fixing 63

mm dia, 15 m long RRL

hose pipe with 63 mm

dia male and female

couplings duly bound with

GI wire, rivets etc.

conforming to IS 636

9 Supplying and fixing air

vessel made of 250 mm

dia, 8 mm thick MS

sheet, 1200 mm in height

with air release valve on

top and flanged

connection to riser, drain

arrangement with 25 mm

dia gun metal wheel valve

accessories, pressure

gauge and painting with

synthetic enamel paint of

approved shade as

10 Supplying, installation,

commissioning of electric

driven terrace pump

suitable for automatic

operation and consisting

of following, complete in

all respects, as required:

(a) Horizontal type,

multistage, centrifugal,

split casing pump of cast

iron body & bronze

impeller with stainless

steel shaft, mechanical

confirming to IS : 1520.

b) Suitable HP squirell

cage induction motor

TEFC type suitable for

operation on 415 volts, 3

phase, 50 Hz, AC supply

with IP55 class of

protection for enclosure,

horiziontal foot mounted

type with Class-'F'

insulation, conforming to

(c) M.S.fabricated

common base plate,

coupling, coupling

guard, foundation bolts

etc.as required.

(d) Suitable cement

concrete foundation

duly plastered and with

anti vibration pads.

TOTAL SCHEDULE ITEM COST 308,108.00

1 PART B (NON SCHEDULED ITEMS - AS PER MARKET RATES)

Supply & erection of ISI

marked portable fire

confirming to IS:15683,

wall mounted type, wall

brackets complete in all

respect as per standard

item with all accessories,

delivery hose & nozzle

whereever required,

including fixing on walls

as per the directions of

Engineer-in-charge.

ABC dry powder Type 6

kg. capacity 4 NOS 2,943.00 11,772.00

CO2 gas type. 4.5 kg.

2 Providing & fixing MR-3

standard carbon steel

fireman axe with rubber

insulated handle tested to

20000 Volts. (MAKE :

Newage (Gujarat) /

Safeguard / Padmini /

3 Providing and fixing MR-4

standard fire hose

cabinet door with frame

(suitable to fit in the

masonry or RCC shaft).

The frame / shutter made

of not less than 1.6 / 1.0

mm thick G.I. / CRCA

sheet having glass

hinged door (4 mm thick

glass) including

necessary locking

arrangement with handle,

4 sets of master keys as

required as per drawings,

including brackets for

mounting accessories, 65

micron powder coating of

required shade. The door

shall be fixed in the

masonry wall or as

required. The words

"FIRE HOSE" to be

painted on the box in Fire

Red Colour. (Make :

ASES (agni suraksha) /

Vidyut control / Dynamic)

TOTAL NON SCHEDULE ITEM COST 80,744.00

COST SUMMARY FOR FIRE FIGHTING WORKS

TOTAL (SCHEDULED ITEM) 308,108.00

TOTAL (NON SCHEDULED ITEM) 80,744.00

COST SUMMARY FOR FIRE FIGHTING WORKS 388,852.00

SCHEDULE OF QUANTITIES FOR ADDRESSABLE FIRE ALARM, PUBLIC ADDRESS AND TALK BACK SYSTEM

PROJECT-HEART BEAT CITY-II_CLUB

S.No DESCRIPTION QTY UNIT RATE AMOUNT

PART-A_DSR ITEM

INTELLIGENT FIRE ALARM SYSTEM

1.21 Supplying and fixing of following sizes of medium class

PVC conduit along with accessories in surface/recess

including cutting the wall and making good the same in

case of recessed conduit as required.

1.53 Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in

the existing surface/ recessed Steel/ PVC conduit as

17.2.1 Supplying, installation, testing and commissioning of micro

processor based intelligent addressable main fire alarm

panel, central processing unit with the following loop

modules and capable of supporting not less than 240 devices

(including detectors) and minimum 120 detectors per loop

and loop length up to 2 km, network communication card,

minimum 320 character graphics/ LCD display with touch

screen or other keypad and minimum 4000 events history log

in the non volatile memory (EPROM), power supply unit (230

± 5% V, 50 hz), 48 hrs back-up with 24 volt sealed

maintenance free batteries with automatic charger. The

panel shall have facility to connect printer to printout log and

facility to have seamless integration with analog/digital voice

evacuation system (which is part of the schedule of work

under SH: PA System) and shall be complete with all

accessories . The panel shall be compatible for IBMS system

with open protocol BACnet/ Modbus over IP complete as per

specifications.

Supplying, installation, testing & commissioning of intelligent

analog addressable photothermal detector complete with

mounting base complete as required. 129 2858.25638 368715.0726

Supplying, installation, testing & commissioning of response

indicator on surface/recessed MS Box having two LED,

metallic cover complete with all connections etc as required. 4 275.77176 1103.087038

Supplying, installation, testing & commisssioning of

intelligent addressable programmable sounder complete as

Supplying, installation, testing & commissioning of fault

17.2.7 isolator complete with base as required. 8 Each 3269.85353 26158.82825

Supplying, installation, testing & commissioning of intelligent

addressable thermal detector with rate of rise cum fixed

17.2.9 tempreature thermistor complete with base as required. 17 Each 2726.20045 46345.40761

Supplying, installation, testing & commissioning of

addressable fire control module complete as required.

17.2.14 Supplying, installation, testing & commissioning of

addressable manual call point complete as required.

17.2.17 Supplying, installation, testing & commissioning of fire fighter

telephone handset complete as required.

Supplying, installation, testing & commissioning of fire fighter

phone jack complete as required.

17.3 PUBLIC ADDRESS SYSTEM

17.3.1 Supplying, installation, testing & commissioning of 6 zone,

voice alarm controller with USB, MP3 player (including 6 zone

button paging station) with seamless integration facility with

main fire alarm panel for voice evacuation complete as

17.3.5 Supplying, installation, testing & commissioning of 6 inches

dia, 2 watts, 70/100 volts ceiling speaker complete as

17.3.9 Supplying, installation, testing & commissioning of Voice

command keypad 6 zone, with microphone assembly

complete as required. 1 Each 81756.1751 81756.1751

17.5.3 Supplying and drawing of cable Fire Retardant PVC insulated

copper conductor cable in the existing surface / recessed

steel conduit of following pairs, cores and size including

connections and interconnections etc. as required.

17.5.3.1 speaker cable Single pair, 2-core, 1.5 sqmm 2575 Metre 53.8854239 138754.9664

TOTAL COST (PART-A_DSR ITEM) 1,665,401

PART-B_NON DSR ITEM

1 Supply, installation, testing and commissioning of Two way Fire

Fighter Phone system complete as required. The Product shall

be UL / FM / VDS Listed .

2 Providing and fixing of self illuminated / auto glow "EXIT" signs

printed on photoluminescent sheet containing self illuminated

base chemical, of appropriate size not less than 300 x 150 mm,

suspended from ceiling or fixed to the walls with accessories as

required and as directed at site. .

TOTAL COST (PART-B_NON DSR ITEM) 108,560

GRAND TOTAL COST (PART-A+PART-B) 1,773,961

GRAND TOTAL COST (PART-A+PART-B) 1,773,961

SCHEDULE OF QUANTITIES FOR CCTV SYSTEM

PROJECT-HEART BEAT CITY-II_CLUB

Description of Item QTY. UNIT RATE AMOUNT

PART-A_DSR ITEM

1.14 Wiring for circuit/ submain wiring alongwith earth wire with the following

sizes of FRLS PVC insulated copper conductor, single core cable in

surface/ recessed PVC conduit as required

1.14.4 2 X 6 sq. mm + 1 X 6 sq. mm earth wire 10 Metre 439 4391

1.21 Supplying and fixing of following sizes of medium class PVC conduit along

with accessories in surface/recess including cutting the wall and making

good the same in case of recessed conduit as required.

1.24 Supplying and fixing following modular switch/ socket on the existing

modular plate & switch box including connections but excluding modular

plate etc. as required.

1.24.4 3 pin 5/6 amp socket outlet 3 Each 121.99 365.9687723

1.27 Supplying and fixing following size/ modules, GI box alongwith modular base

& cover plate for modular switches in recess etc as required.

1.53 Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the

existing surface/ recessed Steel/ PVC conduit as required.

2.3 Supplying and fixing following way, single pole and neutral, sheet steel,

MCB distribution board, 240 volts, on surface/ recess, complete with tinned

copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder

painted including earthing etc. as required. (But without

MCB/RCCB/Isolator)

2.10 Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve,

miniature circuit breaker suitable for inductive load of following poles in the

existing MCB DB complete with connections, testing and commissioning

etc. as required.

2.14 Supplying and fixing following rating, double pole, (single phase and

neutral), 240 volts, residual current circuit breaker (RCCB), having a

sensitivity current upto 300 milliamperes in the existing MCB DB complete

with connections, testing and commissioning etc. as required.

2.11 Supplying and fixing single pole blanking plate in the existing MCB DB

complete etc. as required.

TOTAL COST (PART-A_DSR ITEM) 123,125

PART-B_NON DSR ITEM

1 2 Megapixel IP IR Dome Camera :- Supply, installation, testing and

commissioning of 2 Megapixel,1/2.9 CMOS IP-66 Vandal-proof, Network Dome

Camera ,Day &Night IR cut filter with auto switch,Digital WDR,3D DNR,Video

Compression H.264/MJPEG, ,Minimum Resolution 1920 x 1080:25fps, Built-in

Micro SD/SDHC/SDXC card slot, up to 64 GB ,Line Crossing, Intrusion Detection,

Motion detection, Dynamic analysis,One-key reset, Flash-prevention, dual stream,

heartbeat, mirror,Standard ONVIF, PSIA, CGI, ISAPI,Operating Conditions,-30

°C – 60 °C (-22 °F – 140 °F),PoE (802.3af), IR Range 30 meters, Ingress

Protection,Backlight compensation, ,including RJ45 connector for connection etc.

required for commissioning.

2 Supply, installation, Testing and Commissioning of UL listed NVR . This shall

support minimum 5 clients and include the required hardware cost and the

software cost for the same as per the system requirement. APP allows a quick

remote access and control via mobile phone, having minimum 25 Mbps Incoming

bandwidth & 80Mbps Outgoing bandwidth & recording resolution of video all

channel suitable for 1080 realtime /nonrealtime Live view,H.264/MJPEG dual core

decoding,Max 240fps@1080p,480fps @720p,960 fps @D1 preview &

recording,Up to 5Mp resolution,Support minimum 4 SATA solt for hard disk , 2

USB 2.0,should have 2HDMI ports & 1 VGA port for simultaneous video

output,Support Multi-brand Network camera, ONVIF Version 2.0 with input

voltage of 240 V AC, suitable Hard disk required for 15 days recording

(calculations to be submiited by vendor) complete as per specifications, DVR

should be of same make as Cameras

a) 8 Channel 1 Nos. 33925 33925

3 Supply,installation,testing and commissioning of 10/100/1000 Fast Ehernet

switches- All PoE network switch with 2x Giagbit ports or 2xSFP slots for Fiber

modules with suitable POE budget for camera rating & upto 4 KV surge

protection for camera & POE Port etc required for commisioning.

4 Supply,installation,testing and commissioning of following port loaded jack panel

for CAT6 Cable termination .

5 Supply,installation,testing and commissioning of following port loaded LIU with

adaptor plates , pigtel cables for connections .

6 Supply , Installtion , Testing and comissioning of CAT6 patch cord 3 feet for rack

side switch termination. 18 Nos. 610.65 10991.7

7 Supply , Installtion , Testing and comissioning of SC-LC Single mode fiber patch

8 Supply, Installation, Testing & Commissioning of Fibre Modules 1000BASE-SX

SFP connector. 2 Nos. 12077.3 24154.6

9 Supply,installation,testing and commissioning of 40" CCTV colour Led

Monitor including all accessories complete as required. 74635

10 Supply, installation, testing and commissioning of wall mounted Rack with front

glass door with lock and key arrangement, rear MS door, passive and active

mountable space with active switch installable space, horizontal power manager,

cable manager, twin fan, c complete as required.

11 Supply, Installation, Testing & Commissioning of on line UPS as per following

Technology : Micro processor based controls, True on line, Double conversion

type, should have cold start facility.

Input :- (mains / local D G set compatibility)

a) Voltage : 230 V / 1 Phase

b) Voltage Variation : - 20% to + 20%

c) Input Frequency : 50 Hz.

d) Frequency Variation : + 10%

a) Voltage : 230 V / 1 Phase

b) Voltage Variation : + 1%

c) Frequency Variation : 50 Hz. + 0.1%

Overall Efficiency : > 90%

Charger : Should have built in charger to suit system requirement.

Battery type : Sealed Maintenance Free - SMF

Back-up time : 20 Min. with SMF batteries

(a) Rating : 1 KVA 1 SET 47495 47495

(b) Rating : 2 KVA 1 SET 70564 70564

(c) Rating : 3 KVA 2 SET 89562 179124

TOTAL COST (PART-B_NON DSR ITEM) 853,232

GRAND TOTAL COST (PART-A+PART-B) 976,357

GRAND TOTAL COST (PART-A+PART-B) 976,357

DETAILED ESTIMATE FOR CONSTRUCTION OF CLUB HOUSE AT HEART BEAT CITY-02, NOIDA

BILL OF QUANTITY BASED ON DSR-2021

DSR DESCRIPTION OF ITEM DSR DSR

S. NO. UNIT QUANTITY NDSR RATE NDSR AMOUNT

NO. RATE AMOUNT

1 MR Swimming pool Equipments and accessories Nos -

Supply,installation,testing and commisioning for 1000 DIA TOP MOUNT FRP Filter with 6

way Multiport valve Top Mount Gauge Working Pressure id 2.5 Kg cm2 /36Psi Operating

Temperature 43 Degree complete under the direction of engineer in charge.

Supply,installation,testing and commisioning for 3 HP MOTOR Motor. Ip 55 Rating with

pre filter Total Electrical Separation Ambien t . temperature up to 50 Degree C Capacitor

Inside complete under the direction of engineer in charge.

Supply,installation,testing and commisioning for TEST KIT Water Test Kit Basic Ph` & CI

iii Test Kit Phinol Red - 15 mI Orthotodiline - 15 mI complete under the direction of engineer nos 1.00 754.00 754.00

Supply,installation,testing and commisioning for WALL BRUSH Standard wall Brush (Poly

iv bristle Wall Brush ) Size – 18” Weight - 320gm complete under the direction of engineer in nos 1.00 1,028.00 1,028.00

Supply,installation,testing and commisioning for ALGAE BRUSH Algae Stainless Steel

v Brush ( Hi- Grade Stainless Steel ) Size – 10” Weight – 190gm complete under the nos 1.00 1,165.00 1,165.00

direction of engineer in charge.

Supply,installation,testing and commisioning for TELESCOPIC ROD ALUMINIUM 8 FT.

Telescopic Adjustable Rod Size – 8FT. Long. Body – Aluminum Thickness/Blue/Silver

complete under the direction of engineer in charge.

Supply,installation,testing and commisioning for VACUUM HEAD 18 INCHI Vacuum head

vii with 4 wheel , Alu Body Size - 18 inch Weight – 2.20 Kgs complete under the direction of nos 1.00 3,290.00 3,290.00

engineer in charge.

Supply,installation,testing and commisioning for Hose Pipe 30 Mtr (Per Pcs) Hose Pipe

viii Extruded EVA Vaccum Hose Quality - EVA complete under the direction of engineer in nos 1.00 10,280.00 10,280.00

Supply,installation,testing and commisioning for LEAF NET BLUE/WHITE NET Leaf Net

ix Heavy Duty Plastic Leaf Net complete under the direction of engineer in charge. nos 1.00 1,028.00 1,028.00

Supply,installation,testing and commisioning for SQURE DRAIN BIG Square Main Drain

x Color – White Flow Rate – 850L/Min Squire Main Drain 300mm x 300mm Material – ABS nos 1.00 1,714.00 1,714.00

complete under the direction of engineer in charge.

Supply,installation,testing and commisioning for EYES BALL NOZZLES (6 KG) Floor Inlet

Nozzle Body – ABS Fiber Color – White Flow Rate – 45M3/hr Multiple flow UV Protected

xi Appreciated for long life. Connection 50mm/63mm Suitable for 10Kg & 6 Kg Pressure nos 20.00 411.20 8,224.00

complete under the direction of engineer in charge.

Supply,installation,testing and commisioning for SUCTION VACCUM 6 KG Suction

Nozzle complete under the direction of engineer in charge.

Digitally signed by MOHD

Supply,installation,testing and commisioning for 12V-10W ABS SEVEN INCH Swimming

xiii Pool Under Water Light (12 V- 10W)LED Size - 7" Color – As per Requirement IP 68 nos 22.00 2,946.73 64,828.00

Rating complete under the direction of engineer in charge.

Supply,installation,testing and commisioning for SMPS 30 AMP LED Driver for Light

complete under the direction of engineer in charge.

Supply,installation,testing and commisioning for FOUR STEP LADDER 4 STEP LADDER

MATERIAL - STAINLESS STEEL 304 GRADE Pool Ladder is made with high quality

xv grade Stainless Steel 38/42mm Tube for reliability and durability complete with anchoring nos 2.00 11,650.00 23,300.00

fixtures complete under the direction of engineer in charge.

Supply,installation,testing and commisioning for 12 Inch Double Pin White (Per Mtr)

Swimming Pool Over Flow Grating Color Blue,White UV Protected Material

–PP,CP,Natural Dana Heavy Duty/Non Skid complete under the direction of engineer in

Supply,installation,testing and commisioning for FILTER MEDIA (PER BAG 50 KG)

xvii FILTER MEDIA PACKAGING - 50 KG BAG MASH - 8-16 MASH- 16-32 complete under BAG 26.00 616.77 16,036.00

the direction of engineer in charge.

Providing and fixing the Glass lift as per the specification below:

Model Meta100 MRL Assembled Product Passenger Elevator Capacity 10 persons, 680 kg

Speed 1.0 m/s Stops & Openings 4 Stops, 4 Openings Floor designations G,1,2,3 Machine

type & Location Gearless machine located in the top of overhead Control Duplex Drive

Power supply 415 volts, 3 phase, 50Hz, AC Hoist way dimensions Required 1800mm wide x

2000mm deep Car travel 12900mm Overhead 4600mm Pit depth 1530mm Car dimensions

1100 mm wide x 1600mm deep x 2200mm high Door opening 800mm wide x 2100mm high

Car door 2 panel automatic centre opening with ACVF drive in Stainless steel Hairline finish

Landing door 2 panel automatic centre opening in Stainless steel Hairline finish Car design

Stainless Steel Hairline Finish with Rear Side Glass Panel Car ceiling decoration Stainless

Steel Hairline with round light for car lighting Car flooring 20mm recess provided for

granite/marble flooring (by customer) Handrail Round handrail in Stainless Steel finish

provided on rear wall of car Car operating panel Full Height Landing operating panel

Individual landing operating panel for each elevator complete as per the directions of

engineer-in-charge.

Providing and fixing the Servicce lift as per the specification below:

Model Meta100 MRL Assembled Product Passenger Elevator Capacity 16 persons, 1088 kg

Speed 1.0 m/s Stops & Openings 4 Stops, 4 Openings Floor designations G,1,2,3 Machine

type & Location Gearless machine located in the top of overhead Control Simplex Drive

Power supply 415 volts, 3 phase, 50Hz, AC Hoist way dimensions Required 2400mm wide x

2550mm deep Car travel 12900mm Overhead 4600mm Pit depth 1600mm Car dimensions

1600 mm wide x 1600mm deep x 2200mm high Door opening 1000mm wide x 2100mm

high Car door 2 panel automatic centre opening with ACVF drive in Stainless steel Hairline

finish Landing door 2 panel automatic centre opening in Stainless steel Hairline finish Car

design Stainless Steel Hairline Finish Car ceiling decoration Stainless Steel Hairline with

round light for car lighting Car flooring 20mm recess provided for granite/marble flooring

(by customer) Handrail Round handrail in Stainless Steel finish provided on rear wall of car

Car operating panel Hull Height Landing operating panel Individual landing operating panel

for each elevator complete as per the directions of engineer-in-charge.

TOTAL AMOUNT LIFT - 5,411,480.00

TOTAL AMOUNT LIFT - 5,411,480.00

TOTAL AMOUNT SWIMMING POOL 411,315.00

TOTAL AMOUNT SWIMMING POOL 411,315.00

Digitally signed by MOHD

PROJECT:-AMRAPALI HEARTBEAT 2 CLUB HOUSE

NAME OF WORK: BILL OF QUANTITIES HVAC

Schedule/ Scheduled Non-Scheduled

DSR- Description Unit Qty. Item Item

2019/2022 (Amount Rs.) (Amount Rs.)

A. EQUIPMENTS:

DSR(2019) Variable Refrigerant Volume / Flow Air-conditioning System

-1.0 (Heating & Cooling both)

Supply Installation, Testing & Commissioning of modular type

Variable Refrigerant Flow/Variable Refrigerant Volume air cooled

Outdoor units suitable for cooling and heating, having all

hermetically sealed inverter type Scroll Compressor(s) ,

microprocessor based Controller, top discharge type condensing

unit(s), with R 410 A Refrigerant, vibration isolators, with suitable

foundation etc. complete as required. The unit shall deliver the

rated capacity at AHRI Conditions and work even at 52°C ambient

temperature without tripping (shall submit the OEM printed

document for the same). The unit shall be suitable to work on

400V +/- 10%,3 Phase, 50Hz AC power supply. The unit shall be

filled with first charge of the refrigerant and ready for use as

required. The COP at AHRI conditions shall not be less than 3.1

and IEER not less than 6.5 .

Note: VRF system shall have auto Restart function i.e. In case of

power failure, units should restart automatic when power

resume.The VRF system shall have free phase technology, which

shall correct phases automatically in case of phase reversal.The

rate shall include, duly painted with anti corrosive powder coated

stand for outdoor application for Outdoor unit placement at

terrace.Anti-Corrosive Coating on Brazing Joints of VRV Outdoor

Units and Indoor Units (VRV/VRF OEM

Recommended).Make:Daikin,,LG,Trane,Mitshubishi Electric

Following capacities of ODUs are at standard operating condition

as defined above and Vendor to indicate COP at 100% load & at

part loads i.e. 75% , 50% and 25% in the data sheets/ shop

DSR(2019) EACH

16 HP Cool / Heat Pump Unit 1 262640 262640

DSR(2019) EACH

20 HP Cool / Heat Pump Unit (in cobination of module) 1 328300 328300

DSR(2019) EACH

26 HP Cool / Heat Pump Unit (in cobination of module) 1 426790 426790

DSR(2019) EACH

36 HP Cool / Heat Pump Unit (in cobination of module) 2 590940 1181880

DSR(2019) EACH

40 HP Cool / Heat Pump Unit (in cobination of module) 2 656600 1313200

VRV/VRF 4- Way Cassette Type Units

Supply, installation, testing and commissioning of following

minimum capacity 4-way flow VRV/VRF Cassette Type Indoor

ceiling mounted unit equipped with synthetic washable media pre-

filter, fan section with low noise fan/dynamically balanced

blower, multispeed motor, coil section with DX Copper coil,

electronic expansion valve, outer cabinet, drain pump, grill,

necessary supports, vibration isolation, cord less remote control

etc., suitable for operation on single phase 230 V ± 10%, 50Hz AC

supply, complete, as required. The unit shall have automatic force

shut down provision in case of fire on receiving signal from BMS

System. The cooling capacity of indoor unit will be at air inlet

conditions of 27 Degree C DB and 19 Degree C WB

temperature.Make: Daikin,Hitachi,Mitshubishi Electric,LG.

DSR(2019) EACH

1.6 TR 4- Way Cassette Type Units 3 30204 90612

DSR(2019) EACH

2.0 TR 4- Way Cassette Type Units 4 30801 123204

DSR(2019) EACH

3.2 TR 4- Way Cassette Type Units 18 32787 590166

DSR(2019) EACH

4.0 TR 4- Way Cassette Type Units 7 33981 237867

VRV/VRF High Wall Units

Supply, installation, testing and commissioning of following

minimum capacity VRV/VRF High wall type Indoor unit equipped

with washable synthetic media pre-filter, fan section with low

noise fan/dynamically balanced blower, multispeed motor, coil

section with DX copper coil, electronic expansion valve, outer

cabinet, cord less remote control, drain pan, necessary

accessories etc., suitable for operation on 230 V ± 10%, 50 Hz,

single phase AC supply, complete as required. The unit shall have

automatic force shut down provision in case of fire on receiving

signal from BMS System. The cooling capacity of indoor unit will

be at air inlet conditions of 27 Degree C DB and 19 Degree C WB

temperature..Make: Daikin,Hitachi,Mitshubishi Electric,LG.

DSR(2019) EACH

1.45 TR Highwall Units 1 21315 21315

DSR(2019) EACH

2.0 TR Highwall Units 1 22100 22100

Supply, installation, testing and commissioning of following

minimum capacity and external static pressure VRF/VRV ceiling

mounted ductable type Indoor unit equipped with washable

synthetic media pre-filter, fan section with low noise

fan/dynamically balanced blower, multispeed motor, coil section

with DX copper coil, electronic expansion valve, corded remote

control, outer cabinet, vibration isolators, drain pan, other

necessary supports etc., suitable for operation on single phase AC

supply 230 V ± 10%, 50 Hz complete as required.The unit shall

have automatic force shut down provision in case of fire on

receiveing signal from BMS System. The cooling capacity of

indoor unit will be at air inlet conditions of 27 Degree C DB and 19

Degree C WB temperature. Make:Daikin,LG,Trane,Mitshubishi

DSR(2019) EACH

7.1 TR Ductable Unit 2 87281 174562

VRV/VRF Central Controller for Indoor & Outdoor Units(with

LCD touch screen)

Supply, installation, testing & commissioning of Central Controller

capable of controlling of all IDUs, ODUs complete with necessary

hardware, accessories etc. to perform the following functions:

Control of IDUs, ODUs Units as above with monitoring of vital

parameters such as temperature sensing & setting, ON/OFF,

Permit / prohibit function of each remote controlled unit

Operation of units in individually or in group

Fault indication with Alarm

Provide interface to connect complete VRF system with third

party BMS system

The central controller will be complete including all hardware & EACH

software suitable to perform above function.Complete in all 1 90927 90927

respect as required at site.

NS-2.0 Air handeling Units (Suitable For VRV/VRF System)

Supplying, Installation, testing and commissioning of factory built

DX Type Double skinned panels of Ceiling/Floor Suspended AHU

of 40-23 mm thick panels. Outer sheet of double skinned panels

shall be made of pre-plasticized galvanized sheet, and inner

sheet of plain G.I. Sheet, both inner & outer sheet shall be of 24

gauge,with pressure injected foam insulation (PUF) of density 40

kg/m3 factory injected between them by injection moulding

machine. AHU fan motor(IE2/3) shall have backward/forward

fan. Casing of fan shall be made of galvanized steel sheet. Fan

wheels shall be made of galvanized steel.For AHU Coil, 4/6 Row

DX Coil of 9.5 mm ( Coil row will be as per TR selection from AHU

Supplier).Fan wheels shall be tested and balanced dynamically.

Copper cooling coil section with aluminium finned on copper tube

(6 row deep).The total static pressure required shall be calculated

by the contractor at the time of technical submittal & before

procurement & ordering of equipments.Complete in all ren

cascade mode based on water demand. Note:Pumps should be

The AHU shall be with one set of commissioning filter which shall

be replaced with actual filter. Price shall also be inclusive of all

components described above to make unit complete and

operational as required.

AHUs capacity shall be as follows:

NS-2.1 33.7 TR/13500 CFM FM AHU, 60 mm wc SP Each 1 677735 677735

NS-2.2 15.3 TR/5000 CFM FM AHU, 50 mm wc SP Each 2 251013 502026

Supply ,installation, testing and commissioning of Refrigerant Line Each

accessories kit for AHU suitable to operate with VRV/VRF

NS-3.0 system.System includes Filter Drier, Expansion Valve Kit, 3 115725 347175

Controller,communicator with Wired /wireless remote

etc.Complete as per OEM Standard to run the AHU units.

NS-6.0 Cabinet Type Inline Fans

Supplying, installing, testing and commissioning of INLINE FANS

cabinet type.The casing shall be double skin, internally

acoustically lined and constructed of galvanized steel. All outdoor

application fan shall be of IP 55 rating. The fan shall be backward

curve impeller fitted with maintenance free external rotor motor.

The motor shall be suitable for 220±10%/415±10%(as

required).Cost to include necessary switching / Starter panel

(suitable for out door applications) along with, including cabling

,wiring & earthing as required volt single phase 50 cycles AC

Supplying. All units shall be complete as required with duct

flexible connector and volume control

damper.Make:Airflow,Systemair,Kruger,Nicotra

NS-6.1 Air Quantity : 1500 CFM

Static Pressure : 15 mm wg

Motor rating : As Required

Duty : Kitchen/Store Each 1 35820 35820

NS-6.2 Air Quantity :700 CFM

Static Pressure : 15 mm wg

Motor rating : As Required

Duty : GF Toilet Room Each 2 20665 41330

NS-6.1 Air Quantity : 1000 CFM

Static Pressure : 15 mm wg

Motor rating : As Required

Duty : F1 female & male Toilet Room Each 2 2214 4427

NS-6.2 Air Quantity : 500 CFM

Static Pressure : 15 mm wg

Motor rating : As Required

Duty : 2nd male & female Toilet Room Each 2 79725 159451

Supply, Installation, testing and commissioning of Air-cooled DX

type Hi-wall split air conditioners each comprising an outdoor

unit(s) consisting of hermetically sealed compressor,Inverter type

suitable for operation on 230V, 50Hz, 1 Phase AC supply, air

cooled condenser, condenser fan along with Cooling thermostats

etc. with outer casing and indoor fan coil unit consisting of

centrifugal fans, fan motor, DX cooling coil, outer casing, filter,

control and power panel with remote etc. entire cabling and

wiring from indoor to outdoor, insulation (as per the actual pipe

length) and with full charge of refrigerant gas (including the

increased pipe length, if any) and oil, supports, canvas

connection etc. complete as per drawings. The indoor and

outdoor units shall be with structural steel supports, angles, rods

etc. The quoted price shall also include 24G soft copper

refrigerant piping with 13 mm "O" class factory backed nitrile

rubber with aluminum foil from outdoor unit to indoor unit

complete with insulal of car Car operating panel Hull Height

Landing operating panel Individual landing operating panel for

each elevator complete as per the directions of engineer-in-

charge. engineer-in-charge. BE SUBMITTED; CERTIFI

NS-7.1 2.0 TR split air conditioning units Each 1 104566 104566

NS-7.2 1.5 TR split air conditioning units Each 5 89549 447745

Supply, Installation and commissioning of Non recirculating

centrifugal Air Curtains with following specifications:-

Artistically designed curvaceous body constructed in aluminium

extruded powder coated sections with powder coated sheet

metal base and mounting plates. Motors constructed in

aluminium body to enable rapid cooling, with copper winding,

bearing based motors made in CRNO core to run continuously for

24X7 operation, with thermal overload protection.Dynamically

NS-8.0 balanced centrifugal Blowers made in virgin plastic, with

aerodynamically designed fins to deliver high volume of air., the

suction grills should be made in plastic. Air Curtain should have

dual speed with max. Velocity at Nozzle between 19-21 m/s. Air

curtain should be coupled with the door, with a automatic

magnetic limit switch, to synchronise working of air curtain with

opening of the door.Make:Mitzvah,Mitashi,Mitshubishi.Complete

in all respect as required at site.

Air Curtain / ASP 4210 AP - 3Y, L~2080 mm; H~235 mm; W~208 Each

NS-8.1 mm; Max. Velocity ~ 21,/ 16 m/s; Dual Speed; Al Chassis with CRC 2 44086 88171

Plates,Door 1500W x 2400H

Air Curtain / ASP 4210 AP - 3Y,L~2080 mm; H~235 mm; W~208 Each

NS-8.2 mm; Max. Velocity ~ 21,/ 16 m/s; Dual Speed; Al Chassis with CRC 2 48219 96437

Plates Door 2000W x 2400H

Factory Fabricated Double Skin Air Washer (for fresh air in

Supply, installation, testing and commissioning of factory

fabricated Double Skinned Air-washer unit floor mounted

type fabricated out of extruded aluminum section with

0.6mm pre-plasticized / pre-coated Galvanized steel sheet

outside & 0.6 mm plain Galvanized steel sheet inside with blower,

blower section and blower motor TEFC (IE-3) type suitable

for operation on 415 volts ± 10%, 50 Hz ± 5% AC supply, belt

drive package, wet section & tank shall be made of 18 G

stainless steel. The Air-washer shall be complete with fill of

depth 200 mm & face velocity across the fill shall be limited

to 152 MPM. The Air-washer shall have an efficiency of 90%

& shall be complete with water circulation pump -2

Nos.(1W+1S), GI B Class interconnecting piping, Aluminum

viscous filters. makeup, quick fill and drain connections,

Butterfly/Gate valves for Pumps, make up, drain & quick fill

connections of Sump, 2 Nos. pumps of suitable capacity (1W +1

S), Y strainers and necessary fittings etc.Suitable PCC/RCC

foundation with plaster, Ant vibration arrangement of cushy

foot mountings etc.in all respect shall be in contractor's scope.

The Air-washer shall have an efficiency of 90% & shall be

complete with water circulation pump, GI B Class

interconnecting piping & valves, Aluminum viscous filters, fire

retardant double canvass connection etc. The air washer

panels shall be insulated with 23mm thick & 36 Kg/m³

density PU foam. The Air washer shall conform to specification

given in the tender & shall be of following capacity. Motor Kw is

indicative only, actual as per requirement to be included during

installation.. Complete as required as per site conditions.

NS-11.1 Duty: Kitchen Makeup Air

Air Qty : 8000 CFM

Static Pressure : 50 mm wg

Fan Motor HP : 7.5 HP(Suggested) or as per requirement

Pump Motor HP : 1.5 HP (Suggested) or as per requirement Set 1 286557 286557

NS-12.0 Dry Scrubber With Centrifugal Fan

Supply, Installation, Testing and Commissioning of Scrubber

(including fan) each comprising of extract air intake section,

electrostatic precipitation technology, dry type air cleaner to

remove oil, smoke and fumes from exhaust air, as per the

Specifications. Electrostatic section shall be made of 16 gauge

galvanised sheet, high bake epoxy powder coated, washable type

aluminium mesh filters, stainless steel spiked ionizers to create

high voltage DC field, aluminum collector plates which should be

alternatively charged positive and negative with large collecting

area with 14" deep cell, to work as magnet for charged smoke

and oil particles. Average efficiency of 90-95% in single pass as

per ASHRAE test method. Electrostatic Precipitator should be able

to charge particles from 0.01 micron to 10 microns through solid

state power supply. Collector cell should be of permanent type

and incorporate slide out facility for easy removal for cleaning.

Power supplies shall be 100% solid state UL Listed, Module of

capacity above 3000 CFM shall be equipped with Pulse width

modulating (PWM). The system should be fitted with interlock

switch for safety.

Operating Voltage : 220V, 50 Hz

Ionizing Voltage : 12.5 to 13 KVDC

Collector Cell Voltage : 6 to 6.5 KVDC

Power Consumption : Not more than 50W per cell

NS-12.1 Duty : Kitchen Exhaust

Capacity : 10000 CFM Set 1 654397 654397

Supply, installation, testing & commissioning Refrigerant copper Set

'Y'Joint pair required for distribution of refrigerant in copper

piping press fittings type etc.Complete in all respect as required at

Providing & fixing control cum transmission wiring of 2 core x 1.5 Rmt

sqmm copper in cable tray with refrigerant piping between

indoor units and outdoor units and indoor units and wired

controllers.Complete in all respect as required at site.

TOTAL CARRIED TO SUMMARY A 4772636 4510784

B. REFRIGERANT COPPER PIPING & DRAIN PIPE:

Supply, Installation, testing and commissioning including

vaccumiazation and Nitrogen testing of following nominal sizes of

soft/hard drawn copper refrigerant piping for VRV/VRF system,

complete with fittings, with suitable adjustable ring type hanger

supports, push fitting jointing including accessories, insulated with

Class-O closed cell elastometric nitrile rubber tubular sleeves

sections of specified thickness as given below for Suction and

Liquid lines with factory laminated GC cloth as per

specification,Refrigerant piping shall be laid on heavy duty GI

covered cable trays only at terrace. Entire refrigerant piping work

be carried out in accordance with the specifications. Copper

pipes & fittings Make: MaxiPro, Mexflow, Connex benninger

.Tubler insulation Make : K-flex, Vedoflex,Eurobatex. Copper

Piping shall be of following sizall accessories as per specifications

etc. as required.

DSR(2019) 6.4 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 Rmt

-5.1 mm thick insulation

DSR(2019) 9.5 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 Rmt

-5.2 mm thick insulation

DSR(2019) 12.7 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with Rmt

-5.3 19 mm thick insulation

DSR(2019) 15.86 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with Rmt

-5.4 19 mm thick insulation

DSR(2019) 19 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 Rmt

-5.5 mm thick insulation

DSR(2019) 22.2 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with Rmt

-5.6 19 mm thick insulation

DSR(2019) 25.4 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with Rmt

-5.7 19 mm thick insulation

DSR(2019) 28.58 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm Rmt

-5.8 with 19 mm thick insulation

DSR(2019) 31.8 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm Rmt

-5.9 with 19 mm thick insulation

DSR(2019) 34.9 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm Rmt

-5.10 with 19 mm thick insulation

DSR(2019) 38.1 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm Rmt

-5.11 with 19 mm thick insulation

DSR(2019) 41.27 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm Rmt

-5.12 with 19 mm thick insulation

CONDENSATE DRAIN PIPING

Supply & installation, testing and commissioning of Rigid heavy

class PVC piping complete with fittings, supports as per

NS-11.0 specifications and duly insulated with 6 mm thick nitrile rubber

tubular insulation with factory laminated GC cloth. Make:K-flex,

Vedoflex,Eurobatex

50 mm dia 6mm thick Nitrile rubber with GC laminated tubelar Rmt

32 mm dia 6mm thick Nitrile rubber with GC laminated tubelar Rmt

25 mm dia 6mm thick Nitrile rubber with GC laminated tubelar Rmt

TOTAL CARRIED TO SUMMERY B 1266756 24109

C. DUCTING, GRILLS, DIFFUSER AND INSULATION

Supply, installation, balancing and commissioning of fabricated at

site GSS 120 GSM sheet metal rectangular/round ducting

DSR(2022) .Complete with neoprene rubber gaskets, elbows, splitter

-16.12.2 dampers, vanes, hangers, supports etc. as per approved drawings

and specifications of following sheet thickness complete as

Thickness 0.63 mm sheet (24 Gauge) 430 1058 454940

Thickness 0.80 mm sheet (22 Gauge) 500 1229 614500

Thickness 1.00 mm sheet (20 Gauge) 40 1629 65160

Thickness 1.25 mm sheet (18 Gauge) 10 1793 17930

Supply, installation, testing and commissioning of GI volume Sq.m

DSR(2022) control duct damper complete with neoprene rubber gaskets,

-16.13 nuts, bolts, screws linkages, flanges etc., as per specifications.

Make: Airflow(mapro),Ruskin titus,Systemair.

Supplying & fixing of powder coated extruded aluminium Supply sq.m

Air Grills with aluminium volume control dampers as per 5 9105 45525

specifications. Make: Airflow(mapro),Ruskin titus,Systemair.

Supplying & fixing of powder coated extruded aluminium Return sq.m

DSR(2022) Air Grills with louvers but without volume control dampers

-16.16 complete as required. Make: Airflow(mapro), Ruskin titus,

Supplying, fixing testing commissioning of supply air diffusers sq.m

DSR(2022) round/square flat plate type of powder coated aluminium with

-16.17 aluminium volume control dampers with anti smudge ring &

removable core. Make: Airflow(mapro), Ruskin titus, Systemair.

Supplying, fixing testing commissioning of Return air diffusers sq.m

DSR(2022) round/square flat plate type of powder coated aluminium

-16.18 without volume control dampers with anti smudge ring &

removable core.Make: Airflow(mapro), Ruskin titus, Systemair.

Supplying, Fixing,testing and commissioning of fire dampers in

supply air duct/main branch and return air path as and where

required of required sizes i/c control wiring,the damper shall be

motorized and spring return so as to close the damper in the

event of power failure automatically and open the same in case

of power being restored. The spring return action shall be inbuilt

mechanism and not externally mounted. The damper shall also

be closed in the event of fire signal complete as required and as

per specifications..Make: Airflow(mapro), Ruskin titus, Systemair.

DSR(2022) Sq.m

Fire damper 5 10659 53295

DSR(2022) EACH

Actuator 6 9948 55267

Supplying and fixing of following thickness duly laminated

aluminum foil of mat finish closed cell Nitrile rubber (Class “O”)

insulation on existing duct after applying suitable adhesive for

Nitrile rubber. The joints shall be sealed with 50 mm wide and 3

mm thick self adhesive nitrile rubber tape insulation complete as

per specifications and as required..Make: Armacell,K

DSR(2022) Sq.m

DSR(2022) Sq.m

Supply, installation, testing & commissioning of thermal

insulated flexible duct with flexible duct strap ties following sizes

NS-12.0 duly supported at regular interval as per site requirement

etc.complete as required as per specifications. Make:

Airflow(mapro), Ruskin titus, Systemair.

Supply, fabrication, installation and testing the flexible Sq.m

connections constructed painted MS Frame of fire resistance

flexible double canvas sleeve as per the approved shop

drawings.Make: Airflow(mapro), Ruskin titus, Systemair.

Supplying, installing and testing of Fresh Air powder coated Sq.m

Anodized extruded aluminium construction fresh air louvers (50

NS-14.0 mm deep) (Fresh air louver with VCD , bird screen & rattle- 5 18516 92580

free)complete as per specification.Make: Airflow(mapro), Ruskin

titus, Systemair.

Supplying, installing and testing of Exhaust Air powder coated Sq.m

Anodized extruded aluminium construction fresh air louvers (50

NS-15.0 mm deep) (Fresh air louver without VCD , bird screen & rattle- 3 10608 31824

free)complete as per specification. Make: Airflow(mapro), Ruskin

titus, Systemair.

Supply, Installation, Testing and Balancing of jet diffuser as per SQM

NS-16.0 approved drawings and specifications. Make: Airflow(mapro), 19 12537 238201

Ruskin titus, Systemair.

Supply, installation testing and commissioning of duct acoustic SQM

insulation inside the Duct with Engineered Nitrile Rubber open cell

NS-17.0 foam to be applied using manufacturer's recommended Rubber 50 1659 82936

based Adhesive in a blend of solvents.Make: Armacell,K

flex,Supreme.10 mm thick duct acoustic lining

NS-18.0 G.I. SPIGOT

Supply, Installation and Testing of single piece GI round

spigot made out of spinning process with 50mm height and

having grooves on both sides and circular flanges. Spigots shall be

installed on main ducts to facilitate connection of flexible ducts.

Make: Airflow(mapro), Ruskin titus, Systemair.

Supply, installation ,testing and balancing of extruded aluminium Nos.

NS-19.0 powder coated door transfer grilles. Make: Airflow(mapro), 20 1639 32789

Ruskin titus, Systemair.600 X 150 MM

TOTAL CARRIED TO SUMMERY C 1699618 761559

D. ELECTRICAL FOR HVAC EQUIPMENTS

NS-20.0 HVAC Panel-1 for Outdoor Units

Design, fabrication, assembly, wiring and supply of front operated

dead front cubicle type compartmentalised as per Form 3B, rear

access free standing, dust and vermin proof (IP 65 ingress

protection) main switchboards suitable for use at 415 volts, 3

phase 4 wire 50 Hertz system suitable for a symmetrical fault

level of 25 kA at 415 volts, fabricated from 2 mm thick CRCA MS

sheets with hinged, gasketted (metal based neoprene) and

lockable doors having structural reinforcement with suitable

angle/channel/T/flat sections including 3 mm thick gland plates

on top and bottom and including lifting hooks and including GI

earth strip of required size with 2 nos earthing terminals and

including powder coated paint finish of approved shade over

metal surface cleaned and treated with seven tank process

complete with interconnections etc as per specifications, as

required and as below. Make:Tricolite,Precision Control System ,

Siemens , Schneider

Each Motor control Centre(MCC)/Panel shall include cost of

cabling, wiring, control wiring & inter locking in order to execute

the required sequence of operation.

A separate set of CTs to be provided for wiring from CT’s and

voltage transducers to be brought on to separate set of terminals.

Note : MCCB’s shall be motor duty and suitable for 25 KA (ICS)

Motor Control Centre (415 V) consisting of

OutDoor panels at First Floor Terrace.

One No. 400 amps 4 Pole MCCB ICU=ICS=25KA having front

operating handle with door interlock and as per preamble above

complete with the following :

0 - 400 volts 96 x 96 sq mm digital voltmeter with selector switch -

0 - 400 amps 96 x 96 sq mm digital ammeter with 630/10 amps

CT’s and selector switch - 1 Set

Over voltage tripping mechanism for persistent voltage exceeding

110% of the rated voltage for more than 5 minutes - 1 Set

iv. Phase indicating lamps, with toggle switches.

v. Terminals to receive XLPE insulated Aluminium cables

TPN bus bars shall be of aluminium and shall be sleeved. Phase

bus bars shall be rated at 650 amps and neutral bus bar shall be

of 50% capacity suitable to withstand symmetrical fault level of

Maximum density of aluminium bus bars for current carrying

capacity shall be one amp per square mm.

2 Nos. 25 amps MCCB outgoing feeders to VRV outdoor unit

.Each of these compartment shall contain CT operated digital

ammeter of 0-25 amps range with selector switch, and an

indicating lamp with MCB and toggle switch for ‘ON’ status.(1

spare but without metering )

7 Nos. 40 amps MCCB outgoing feeders to VRV outdoor unit

.Each of these compartment shall contain CT operated digital

ammeter of 0-40 amps range with selector switch, and an

indicating lamp with MCB and toggle switch for ‘ON’ status.(1

spare but without metering )

6 Nos. 63 amps MCCB outgoing feeders to 18 HP VRV outdoor

unit .Each of these compartment shall contain CT operated digital

ammeter of 0-63 amps range with selector switch, and an

indicating lamp with MCB and toggle switch for ‘ON’ status.(1

spare but without metering )

Supplying,Receiving, fixing, testing & commissioning of HVAC Set

Panel for VRV as described above.Complete as required as per 1 413304 413304

site conditions.

NS-22.0 CONTROL PANELS FOR AIR WASHER & SCRUBBER

Design, manufacture, supply, installation, testing and

commissioning of the following cubicle type, dead front, sheet

steel, wall mounted control panels, including anchoring into the

wall, wiring terminating into MCCB and copper earthing, in each

panel shall be provided by the electrical contractor.Complete as

required as per site conditions.Make:Tricolite,Precision Control

System , Siemens , Schneider

All outgoing shall be provided with Stop /Manual /Auto selector

switch to facilitate operation through BAS. All starters shall be

provided with potential free Contact for Connections to Building

Automation System.

All wiring and copper earthing of motors from the panel shall be

The panel shall include DOL/SD starter with over load ,single

phase,undervoltage & over voltage,phase reverse protection with

necessary internal wiring.Starter panel shoul meet the

requirement of various loads.

a. For 5-15 HP MCCB/MCB as per the ratings.

b. DOL / SD starter as per HP ratings

c. Terminal block for power distribution.

d. Contractor, over load relay with built in single phasing protection.

e. Phase indicating lights and indicating light for ON status.

f. Digital voltmeter and digital ammeter with selector switches.

Time delay relay for delayed automatic restart of air handling unit

For on/off/remote and local operation, 3 pole single throw switch

h. shall be provided in each AHU panel to facilitate override of the

automatic operation.

All starters shall be provided with suitable potential free contact

for connections to the Building Automation System.

3 Nos of Single Pole MCB's Shall be provided at the incoming Set

section of the starter panel for fire damper actuator & as a spare.

NS-27.0 AHU Panel-3.7kW

1 No. 25 A TP MCCB, 25 kA breaking capacity with thermal

release and adjustable setting and with rotary handle.

B METERING & INDICATION

1 Set - digital multifunction meter (showing harmonics along with

all other electrical parameters such as voltage current, Hz, KW,

KWHr, PF.) with RS 485 port with matching cast resin CT's

1 Set - 0-25V 96 sqmm Voltmeter with selector switch, 3 No.

phase indicating LED lamp to show the incoming power with

control SP MCB.

1Set of indicating LED lamps for MCCB On/Off with protective SP

1 Set of CTs of the ratio 25/5A with class 0.5 Accuracy for

Metering, burden 15 VA

40A TPN Aluminium Bar with colour coded PVC Sleeves

2 Nos. 40A TP MPCB (including 1 no spare) with 1 No. 5.0 HP DOL

3 Nos. 10A DP MCB

Note- Necessary wiring and interlocking for the above

equipments shall be done with the Fire Alarm system such that

required fan gets actuated and shut off the AHU in case of fire

as per fire zones. No/NC contacts & supply arrangements shall

also be spared for the fire damper actuation & control.

Supplying,Receiving, fixing, testing & commissioning of AHU Set

Panel as described above.Complete as required as per site 2 41330 82661

NS-28.0 AHU Panel-5.5kW

1 No. 25A TP MCB, 25 kA breaking capacity with thermal release

and adjustable setting and with rotary handle.

B METERING & INDICATION

1 Set - digital multifunction meter (showing harmonics along with

all other electrical parameters such as voltage current, Hz, KW,

KWHr, PF.) with RS 485 port with matching cast resin CT's

1 Set - 0-40 V 96 sqmm Voltmeter with selector switch, 3 No.

phase indicating LED lamp to show the incoming power with

control SP MCB.

1Set of indicating LED lamps for MCCB On/Off with protective SP

1 Set of CTs of the ratio 40/5A with class 0.5 Accuracy for

Metering, burden 15 VA

40A TPN Aluminium Bar with colour coded PVC Sleeves

2 Nos. 40A TP MPCB (including 1 no spare) with 1 No. 5.0 HP DOL

3 Nos. 10A DP MCB

Note- Necessary wiring and interlocking for the above

equipments shall be done with the Fire Alarm system such that

required fan gets actuated and shut off the AHU in case of fire

as per fire zones. No/NC contacts & supply arrangements shall

also be spared for the fire damper actuation & control.

Supplying,Receiving, fixing, testing & commissioning of AHU Set

Panel as described above.Complete as required as per site 1 61996 61996

NS-30.0 Isolator Switches With Metal Enclosure

20A RCCB (300 mA),4pole switch for VRV Outdoor units with Each

sheet metal enclosure, rain protection etc. as required to suit the

site condition. (Enclosure shall be suitable for out door

installation.).Complete as required as per site

conditions.Make:Tricolite,Precision Control System , Siemens ,

25A RCCB (300 mA),4pole switch for VRV Outdoor units with Each

sheet metal enclosure, rain protection etc. as required to suit the

site condition. (Enclosure shall be suitable for out door

installation.).Complete as required as per site

conditions.Make:Tricolite,Precision Control System , Siemens ,

40A RCCB (300 mA),4pole switch for VRV Outdoor units with Each

sheet metal enclosure, rain protection etc. as required to suit the

site condition. (Enclosure shall be suitable for out door

installation.).Complete as required as per site

conditions.Make:Tricolite,Precision Control System , Siemens ,

63A RCCB (300 mA),4pole switch for VRV Outdoor units with Each

sheet metal enclosure, rain protection etc. as required to suit the

site condition. (Enclosure shall be suitable for out door

installation.).Complete as required as per site

conditions.Make:Tricolite,Precision Control System , Siemens ,

16A 2/3 Pole isolator switch for equipments with sheet metal Each

enclosure, rain protection etc. as required to suit the site

NS-30.5 condition. (Enclosure shall be suitable for out door 3 4822 14466

installation.).Make:Tricolite,Precision Control System , Siemens ,

NS-31.0 Cables form Air Conditioning Panel to each of ODUs

Supply, laying, Installation and Testing of the following sizes of

PVC insulated and FR PVC Round Sheathed, Copper Conductor

(unarmoured) cable, 1100 Volt. Cables shall be inclusive of all

clamps,saddles,screws,cable identification tags, cable terminal

joints including terminal lugs, insulating tapes, affecting

terminal connections to the equipment as per the

specifications and as required. Make:RR Cable, KEI, Worldcab.

Complete as required as per site conditions.

NS-32.0 MV Cable

Supply, laying & fixing of following sizes of PVC sheathed

PVC/XLPE insulated Aluminium conductor/copper conductor

power/ multicore control armoured cable of 1.1 KV

grade.Make:RR Cable, KEI, Worldcab..Complete as required as

per site conditions.

NS-32.1 4C- 6 sq mm Aluminium Metre 285 212 60466

NS-32.2 4C- 4 sq mm Aluminium Metre 169 167 28172

Note: All control & power supply cables used for Smoke exhaust

fans shall be FS type only.

Supplying and installing following size of powder coated M.S.

cable trays with cover suitable for outdoor application,

perforation not more than 17.5%, in convenient sections, joined

with connectors, suspended from the ceiling with M.S.

suspenders with heavy cover including bolts & nuts, painting

suspenders etc. as required.Make: Aditya Steel,MEM,RICO

150 mm width X 50 mm depth X 1.6 mm thickness powder Metre

coated with heavy duty cover for outdoor application

4.1.4 300 mm width X 50 mm depth X 1.6 mm thickness Metre 300 777 233100

TOTAL CARRIED TO SUMMERY D 305580 1884656