Comprehensive repair and maintenance of newly allotted quarters (Phase-3) in Bokaro Steel City Township

Modified Estimated Cost after using Correction

Included in rate

factor on DSR 2023 on account of

W GRAND TOTAL 7,01,34,621

W GRAND TOTAL 7,01,34,621

Name of Work- Comprehensive Repair and Maintenance of Newly Allotted Quarters (Phase-3) at Bokaro Steel City, Jharkhand.

DSR 2023 AMOUNT

SL NO ITEM DESCRIPTION UNIT QTY Rate AMOUNT (DSR)

Ref No. (NON DSR)

Building Civil Works

Earth work in excavation by mechanical means (Hydraulic

excavator) / manual means over areas (exceeding 30cm in depth,

2.6 1.5m in width as well as 10 sqm on plan) including getting out and -

disposal of excavated earth, lead up to 50m and lift up to 1.5m,as

directed by Engineer-in-Charge.

Filling available excavated earth (excluding rock) in trenches,

plinth, sides of foundations etc. in layers not exceeding 20cm in

2 2.25 depth, consolidating each deposited layer by ramming and cum 50.00 209.78 10,488.94

watering, lead up to 50 m and lift up to 1.5 m.

Excavating, supplying and filling of local earth (including royalty)

by mechanical transport up to a lead of 5 km, also including

3 2.25A ramming and watering of the earth in layers not exceeding 20 cm cum 50.00 749.75 37,487.26

in trenches, plinth, sides of foundation etc., complete.

Supplying and filling in plinth with sand under floors, including

4 2.27 watering, ramming, consolidating and dressing complete. cum 100.00 2273.05 2,27,304.96

Clearing jungle including uprooting of rank vegetation, grass, brush

wood, trees and saplings of girth up to 30 cm measured at a height

5 2.31 of 1 m above ground level and removal of rubbish up to a distance sqm 5000.00 18.84 94,186.40

of 50m outside the periphery of the area cleared.

Diluting and injecting chemical emulsion for POST-

2.35 CONSTRUCTIONAL anti- termite treatment (excluding the cost of

chemical emulsion) :

Treatment of soil under existing floors using chemical emulsion @

one litre per hole, 300 mm apart including drilling 12 mm diameter

holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse

sand) to match the existing floor :

6 2.35.3.1 With Chlorpyriphos/Lindane E.C. 20% with 1% concentration. sqm 1200.00 331.85 3,98,215.82

Treatment of existing masonry using chemical emulsion @ one

litre per hole at 300 mm interval including drilling holes at 45

degree and plugging them with cement mortar 1:2 (1 cement : 2

coarse sand) to the full depth of the hole :

7 2.35.4.1 With Chlorpyriphos/Lindane E.C. 20% with 1% concentration. nos 2000.00 46.02 92,045.80

Treatment at points of contact of wood work by chemical

emulsion Chlorpyriphos/ Lindane (in oil or kerosene based

8 2.35.5 solution) @ 0.5 litres per hole by drilling 6 mm dia holes at meter 1500.00 299.36 4,49,044.37

downward angle of 45 degree at 150 mm centre to centre and

sealing the same.

Extra for levelling & neatly dressing of disposed soil completely as

directed by Engineer-in-Charge.

Reinforced Concrete work for counters

1:2:4 (1 cement : 2 coarse sand(zone-III) derived from natural

10 4.1.3 sources : 4 graded stone aggregate 20 mm nominal size derived cum 37.68 8432.36 3,17,724.98

from natural sources)

Reinforced cement concrete work in beams, suspended floors,

roofs having slope up to 15° landings, balconies, shelves, chajjas,

lintels, bands, plain window sills, staircases and spiral stair cases

above plinth level up to floor five level, excluding the cost of

centering, shuttering, finishing and reinforcement with 1:1.5:3 (1

cement : 1.5 coarse sand(zone-III)derived from natural sources : 3

graded stone aggregate 20 mm nominal sizederived from natural

Centering and shuttering including strutting, propping etc. and

Shelves (Cast in situ)

Providing precast cement concrete Jali 1:2:4 (1 cement : 2 coarse

sand(zone-III) : 4 graded stone aggregate 6mm nominal size ),

reinforced with 1.6 mm dia mild steel wire, including centering

and shuttering, roughening cleaning, fixing and finishing in cement

mortar 1:3 (1 cement: 3 fine sand) etc. complete, excluding

plastering of the jambs, sills and soffits.

DSR 2023 AMOUNT

SL NO ITEM DESCRIPTION UNIT QTY Rate AMOUNT (DSR)

Ref No. (NON DSR)

Steel reinforcement for R.C.C. work including straightening,

cutting, bending, placing in position and binding all complete upto

plinth level. Thermo Mechanically Treated bars of grade Fe-500D

Brick work with clay flyash F.P.S. (non modular) brick of class

15 6.32.2 designation 7.5 in superstructure above plinth level up to floor five cum 50.00 9734.43 4,86,721.60

level in : Cement mortar 1:6 (1 cement : 6 coarse sand)

6.13 Half brick masonry with common burnt clay F.P.S. (non modular)

bricks of class designation 7.5 in superstructure above plinth level

up to floor V level.

16 6.13.2 Cement mortar 1:4 (1 cement :4 coarse sand) sqm 50.00 1202.80 60,140.16

Providing and fixing 18mm thick gang saw cut ( premoulded and

prepolished) machine cut for kitchen platforms, vanity counters,

window sills, facias and similar locations of required size of

approved shade, colour and texture laid over 20mm thick base

17 8.2.1.1 cement mortar 1:4 (1 cement : 4 coarse sand) with joints treated sqm 50.00 3654.86 1,82,743.02

with white cement, mixed with matching pigment, epoxy touch

ups, including rubbing, curing, moulding and polishing to edge to

give high gloss finish etc. complete at all levels.

Marble Area of slab over 0.50 Sqm.( For Counter)

Extra for fixing marble /granite stone, over and above

corresponding basic item, in facia and drops of width upto 150

mm with epoxy resin based adhesive, including cleaning etc.

Extra for providing opening of required size & shape for wash

basin/kitchen sink in kitchen platform, vanity counter and similar

19 8.5 location in marble/ Granite/ stone work, including necessary holes nos 41.29 1047.50 43,248.15

for pillar taps etc. including moulding, rubbing and polishing of cut

edges etc. complete

Providing and fixing Ist quality ceramic glazed wall tiles conforming

to IS: 15622 (thickness to be specified by the manufacturer), of

approved make, in all colours, shades except burgundy, bottle

green, black of any size as approved by Engineer-in-Charge, in

skirting, risers of steps and dados, over 12 mm thick bed of

cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with

grey cement slurry @ 3.3kg per sqm, including pointing in white

cement mixed with pigment of matching shade complete

Providing wood work in frames of doors, windows, clerestory

windows and other frames, wrought framed and fixed in position

with hold fast lugs or with dash fasteners of required dia & length

(hold fast lugs or dash fastener shall be paid for separately).

21 9.1.1 Second class teak wood Cum 2.00 152999.06 3,05,998.13

9.7.7 Float glass panes

23 9.7.7.1 4 mm thick glass pane (weight not less than 10 kg/sqm). sqm 300.00 2399.40 7,19,819.56

5.0 mm thick glass panes (weight not less than 12.50 kg/sqm).

Providing and fixing glazed shutters for doors, windows and

clerestory windows using 4 mm thick float glass panes (weight not

9.9 less than 10 kg per sqm) fixing with ISI marked M.S. pressed butt

hinges bright finished of required size with necessary screws.

9.9.1 Second class teak wood

9.16 Providing and fixing 25 mm thick shutters for cup board etc.

9.16.1 Panelled or panelled & glazed shutters

Second class teak wood including ISI marked nickel plated bright

finished M.S. piano hingeswith necessary screws

Providing and fixing ISI marked flush door shutters conforming to

IS : 2202 (Part I) non-decorative type, core of block board

9.21 construction with frame of 1st class hard wood and well matched

commercial 3 ply veneering with vertical grains or cross bands and

face veneers on both faces of shutters:

30 mm thick including ISI marked Stainless Steel butt hinges with

necessary screws

DSR 2023 AMOUNT

SL NO ITEM DESCRIPTION UNIT QTY Rate AMOUNT (DSR)

Ref No. (NON DSR)

Extra for providing lipping with 2nd class teak wood battens 25

28 9.23 mm minimum depth on all edges of flush door shutters (over all Sqm 650.00 494.85 3,21,654.58

area of door shutter to be measured).

9.48 Providing and fixing M.S. grills of required pattern in frames of

windows etc. with M.S. flats, square or round bars etc. including

priming coat with approved steel primer all complete.

29 9.48.1 Fixed to steel windows by welding kg 100.00 234.50 23,450.27

9.48.2 Fixed to openings /wooden frames with rawl plugs screws etc.

9.51 Providing and fixing fly proof galvanized M.S. wire gauge to

windows and clerestory windows using wire gauge with average

width of aperture 1.4 mm in both directions with wire of dia 0.63

mm all complete.

31 9.51.1 With second class teak wood beading 62X19 mm sqm 100.00 1400.33 1,40,032.70

32 9.51.2 With 12 mm mild steel U beading sqm 100.00 1005.23 1,00,522.58

Providing 40x5 mm flat iron hold fast 400 mm long including fixing

to frame with 10 mm diameter bolts, nuts and wooden plugs and

33 9.53 embedding in cement concrete block 300x100x150 mm 1:3:6 mix Each 1500.00 244.94 3,67,407.23

(1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm

Providing and fixing ISI marked IS:1341 M.S. pressed butt hinges

bright finished with necessary screws etc. complete :

Providing and fixing oxidised M.S. hasp and staple (safety type)

9.67 conforming to IS : 363 with necessary screws etc. complete

(Copper oxidised as per IS 1378)

Providing and fixing oxidised M.S. casement stays (straight peg

9.68 type) with necessary screws etc. complete (Copper oxidised as per

41 9.68.1 300 mm weighing not less than 330 grams No 1500.00 72.14 1,08,207.33

42 9.68.2 250 mm weighing not less than 280 grams Nos 1500.00 65.34 98,012.72

Providing and fixing chromium plated brass 100 mm mortice latch

43 9.88 and lock with 6 levers and a pair of lever handles of approved Nos 50.00 1068.53 53,426.70

quality with necessary screws etc. complete.

Providing and fixing chromium plated brass 50 mm cupboard or

wardrobe knobs with nuts complete.

Providing and fixing chromium plated brass handles with

necessary screws etc. complete:

Providing and fixing aluminium sliding door bolts ISI marked

anodised (anodic coating not less than grade AC 10 as per IS :

1868) transparent or dyed to required colour or shade with nuts

and screws etc. complete :

Providing and fixing aluminium tower bolts ISI marked anodised

(anodic coating not less than grade AC 10 as per IS : 1868 )

transparent or dyed to required colour or shade with necessary

screws etc. complete :

Providing and fixing aluminium pull bolt lock, ISI marked, anodised

(anodic coating not less than grade AC 10 as per IS : 1868)

transparent or dyed of required colour and shade, with necessary

screws bolts, nut and washers etc. complete.

Providing and fixing aluminium handles of approved make

anodized (anodic coating not less than grade AC 10 as per IS :

1868) transparent or dyed to required colour or shade with

necessry screws etc. complete.

Providing and fixing aluminium hanging floor door stopper ISI

marked anodised (anodic coating not less than grade AC 10 as per

IS : 1868) transparent or dyed to required colour and shade with

necessary screws etc. complete.

DSR 2023 AMOUNT

SL NO ITEM DESCRIPTION UNIT QTY Rate AMOUNT (DSR)

Ref No. (NON DSR)

54 9.101.1 Single rubber stopper Each 1000.00 42.38 42,383.88

Providing and fixing factory made uPVC door frame made of uPVC

extruded sections having an overall dimension as below (tolerance

±1mm), with wall thickness 2.0 mm (± 0.2 mm), corners of the

door frame to be Jointed with galvanized brackets and stainless

9.117 steel screws, joints mitred and Plastic welded. The hinge side

vertical of the frames reinforced by galvanized M.S. tube of size 19

X 19 mm and 1mm (± 0.1 mm) wall thickness and 3 nos. stainless

steel hinges fixed to the frame complete as per manufacturer ’s

specification and direction of Engineer in-charge

55 9.117.1 Extruded section profile size 48x40 mm Rmt 1200.00 289.20 3,47,034.07

9.118 Providing and fixing to existing door frames.

24 mm thick factory made PVC door shutters made of styles and

rails of a uPVC hollow section of size 59x24 mm and wall thickness

2 mm (± 0.2 mm) with inbuilt edging on both sides. The styles and

rails mitred and joint at the corners by means of M.S. galvanised/

plastic brackets of size 75x220 mm having wall thickness 1.0 mm

and stainless steel screws. The styles of the shutter reinforced by

inserting galvanised M.S. tube of size 20x20 mm and 1 mm (± 0.1

mm) wall thickness. The lock rail made up of 'H' section, a uPVC

hollow section of size 100x24 mm and 2 mm (± 0.2 mm) wall

thickness, fixed to the shutter styles by means of

plastic/galvanised M.S. 'U' cleats. The shutter frame filled with a

uPVC multi-chambered single panel of size not less than 620 mm,

having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall

thickness. The panels filled vertically and tie bar at two places by

inserting horizontally 6 mm galvanised M.S. rod and fastened with

nuts and washers, complete as per manufacturer's specification

and direction of Engineer-in-charge. (For W.C. and bathroom door

Providing and fixing factory made Fiberglass Reinforced Plastic

(F.R.P.) Chhajja 4mm thick of required colour size and design made

of Resin Transfer moulding (RTM)Machine technology, resulting in

void free compact laminate in single piece, having smooth gradual

slope curvature for easy drainage of water and duly reinforced by

2 nos vertically and 1 no horizontally mm thick MS flat with 12mm

inbuilt hole for grouting on the existing wallalongwith 50mm

flangesduly inserted and sealed in the wall completein one single

57 9.128 piece casted monolithically, including all necessary fittings. The sqm 30.00 5573.53 1,67,206.01

FRP chhajja should be manufactured using unsaturated polyester

resin as per IS: 6746, duly reinforced with fiber glass chopped

strand mash (CSM) as per IS:11551 complete with protective Gel

coat U/V coating on top for complete resistance from the extreme

of tempetrature, weather & sunlight (only plan area of chhajjas

shall be measured for making payment)

9.147A Providing and fixing factory made uPVC glazed/wire mesh

windows/doors comprising of lead free uPVC multi-chambered

frame, sash and mullion/coupler (where ever required) extruded

profiles having minimum wall thickness of 1.70 mm for Series R1

and R2 profiles and 2.10 mm for Series R3 and R4 profiles

conforming to EN: 12608 in any shape, colour and design duly

reinforced with galvanized mild steel section made of required

shape & size as per CPWD Specification, uPVC extruded glazing

beads, interlocks and Inline sash adaptor (where ever required) of

appropriate dimension, EPDM gasket, hardware, SS 304 grade

fasteners of minimum 8 mm dia with countersunk head,

comprising of matching polyamide PA6 grade sleeve for fixing

frame to finished wall as per IS 1367 : Part 1 to 14, plastic packers,

plastic caps and necessary stainless steel screws etc. Profile of

frame, sash & mullion (if required) shall be mitred cut and fusion

welded/mechanically jointed duly sealed at all corners, including

drilling of holes for fixing hardware and drainage of water etc.

After fixing frame the gap between frame and adjacent finished

wall shall be filled with weather proof silicon sealant over backer

rod pf approved size and quality, all complete as per approved

drawing conforming to CPWD specification & direction of

Engineer-in-Charge.

DSR 2023 AMOUNT

SL NO ITEM DESCRIPTION UNIT QTY Rate AMOUNT (DSR)

Ref No. (NON DSR)

Section of steel reinforcement and cross sections of uPVC profiles

to be as per design approved by Engineer-in-Charge. Wire mesh /

Glazing of plain/ toughened/ laminated/ double glass unit with /

without high performance coatings as per design requirements

and conforming to IS: 3548 & IS:16231 shall be paid separately.

Note:- Structural design proof checked from a Government

Engineering Institute, to be provided by the manufacturer for:

(i) Sites with basic wind speed > 45 m/sec as per IS 875 - Part 3

(ii) Sites with structure height more than 20m for all wind speeds.

9.147.A1 Two track two panels sliding window with Aluminium channel for

roller track, wool pile, nylon rollers with SS 304 body.

9.147.A1.1 Using R2 series with frame (40mm & above) x (40mm & above) &

sash (25mm & above) x (50mm & above) with zinc alloy (zamak)

powder coated touch locks with hook (Height upto 1.2 meter)

9.147.D1 Ventilator Casement window single panel with or without fixed

panel with S S. 304 friction hinges as per size and weight of sash,

single point locking zinc alloy (zamak) powder coated handles.

9.147.D1.1 Using R1 series with frame (33mm & above ) x (35mm & above) &

59 sash /mullion (33mm & above) x (50 mm & above). (Height upto sqm 50.00 14129.24 7,06,462.22

9.147.E1 Casement window single panel with S.S. 304 friction hinges as per

size and weight of sash, multi-point locking system, zinc alloy

(zamak) powder coated handles.

9.147.E1.1 Using R2 series with frame (39mm & above) x (39mm & above) &

60 sash (39mm & above) x (60mm & above). (Height upto 1.2 meter) sqm 50.00 15465.03 7,73,251.61

Providing and fixing bright /matt finished Stainless Steel handles of

9.165 approved quality & make with necessary screws etc all complete.

Providing and fixing M.S. grills of required pattern in frames of

windows etc. with M.S. flats, square or round bars etc. including

priming coat with approved steel primer all complete.

MS Grills for windows, Fixed to openings

Fixing standard steel glazed doors, windows and ventilators in

walls, including fixing of float glass panes with glazing clips and

special metalsash putty of approved make, or metal beading with

screws, (only steel windows, glass panes cut to size and glazing

clips or metal beading with screws, shall be supplied by

department free of cost.

Fixing with 15x3 mm lugs 10 cm long embedded in cement

65 10.10.1 concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse kg 500.00 88.25 44,123.12

sand : 6 graded stone aggregate 20 mm nominal size).

Providing and fixing T-iron frames for doors, windows and

ventilators of mild steel Tee-sections, joints mitred and welded,

10.13 including fixing of necessary butt hinges and screws and applying a

priming coat of approved steel primer.

Fixing with 15x3 mm lugs 10 cm long embedded in cement

66 10.13.1 concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse kg 500.00 151.66 75,830.76

sand : 6 graded stone aggregate 20 mm nominal size).

Welding by gas or electric plant including transportation of plant

at site etc. complete.

DSR 2023 AMOUNT

SL NO ITEM DESCRIPTION UNIT QTY Rate AMOUNT (DSR)

Ref No. (NON DSR)

Providing and fixing stainless steel ( Grade 304) railing made of

Hollow tubes, channels, plates etc., including welding, grinding,

buffing, polishing and making curvature (wherever required) and

fitting the same with necessary stainless steel nuts and bolts

complete, i/c fixing the railing with necessary accessories &

68 10.28 stainless steel dash fasteners , stainless steel bolts etc., of required Kg 120.00 826.70 99,203.97

size, on the top of the floor or the side of waist slab with suitable

arrangement as per approval of Engineer-incharge, (for payment

purpose only weight of stainless steel members shall be

considered excluding fixing accessories such as nuts, bolts,

fasteners etc.).

Brick on edge flooring with bricks of class designation 7.5 on a bed

of 12 mm cement mortar, including filling the joints with same

mortar, with common burnt clay non modular bricks:

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4

graded stone aggregate) finished with a floating coat of neat

cement, including cement slurry, but excluding the cost of nosing

of steps etc. complete.

70 11.3.1 40 mm thick with 20 mm nominal size stone aggregate sqm 1912.20 657.38 12,57,040.59

Chequerred precast cement concrete tiles 22 mm thick in footpath

&courtyard, jointed with neat cement slurry mixed with pigment

11.20 to match the shade of tiles, including rubbing and cleaning etc.

complete, on 20mm thick bed of cement mortar 1:4 (1 cement: 4

71 11.20.1 Light shade pigment using white cement. sqm 50.00 1500.56 75,028.03

Medium shade pigment using 50% white cement 50% Grey

73 11.20.3 Dark shade pigment using ordinary cement. sqm 50.00 1198.20 59,910.04

74 11.20.4 Ordinary cement without any pigment. sqm 50.00 1130.61 56,530.57

Providing and laying rectified Glazed Ceramic floor tiles of size

300x300 mm or more (thickness to be specified by the

manufacturer), of 1st quality conforming to IS : 15622, of

approved make, in all colours, shades, except White, Ivory, Grey,

Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1

Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3

kg/ sqm including pointing the joints with white cement and

matching pigments etc., complete.

Providing and laying Vitrified tiles in floor in different sizes

(thickness to be specified by the manufacturer) with water

absorption less than 0.08% and conforming to IS:15622, of

approved brand & manufacturer, in all colours and shade, laid on

20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing

11.41A with grey cement slurry @3.3 kg/sqm including grouting the joints

with white cement and matching pigments etc. The tiles must be

cut with the zero chipping diamond cutter only . Laying of tiles will

be done with the notch trowel, plier, wedge, clips of required

thickness, leveling system and rubber mallet for placing the tiles

gently and easily.

Double charge vitrified tile polished finish of size

Providing and fixing on wall face unplasticised Rigid PVC rain water

pipes conforming to IS : 13592 Type A, including jointing with seal

ring conforming to IS : 5382, leaving 10 mm gap for thermal

expansion, (i) Single socketed pipes. 110 mm diameter

Providing and fixing on wall face unplasticised - PVC moulded

fittings/ accessories for unplasticised Rigid PVC rain water pipes

79 12.42.4.2 conforming to IS : 13592 Type A, including jointing with seal ring Each 500.00 236.91 1,18,455.45

conforming to IS : 5382, leaving 10 mm gap for thermal

expansion:Single tee with door 110x110x110 mm

Providing and fixing on wall face unplasticised - PVC moulded

fittings/ accessories for unplasticised Rigid PVC rain water pipes

80 12.42.5.2 conforming to IS : 13592 Type A, including jointing with seal ring Each 200.00 160.92 32,183.92

conforming to IS : 5382, leaving 10 mm gap for thermal

expansion:Bend 87.5° 110 mm bend

DSR 2023 AMOUNT

SL NO ITEM DESCRIPTION UNIT QTY Rate AMOUNT (DSR)

Ref No. (NON DSR)

Providing and fixing on wall face unplasticised - PVC moulded

fittings/accessories for unplasticised Rigid PVC rain water pipes

81 12.42.6.2 conforming to IS : 13592 Type A, including jointing with seal ring Each 200.00 141.12 28,223.81

conforming to IS : 5382, leaving 10 mm gap for thermal

expansion:Shoe (Plain) 110 mm Shoe

Providing and fixing precoated galvanised iron profile sheets (size,

shape and pitch of corrugation as approved by Engineer-in-Charge)

of total coated thickness 0.50mm (base metal of minimum

0.45mm thickness with total coating thickness of 0.05mm) with

zinc coating 120 grams per sqm as per IS:277, in 240 mpa steel

grade, 5-7 microns epoxy primer on both side of the sheet and

polyester top coat 15-18 microns. Sheet should have protective

guard film of 25 microns minimum to avoid scratches during

transportation and should be supplied in single length upto 12

metre or as desired by Engineer-in- charge. The sheet shall be

fixed using self drilling /self tapping screws of size (5.5x 55 mm)

with EPDM seal, complete upto any pitch in horizontal/ vertical or

curved surfaces, excluding the cost of purlins, rafters and trusses

and including cutting to size and shape wherever required.

Providing and fixing precoated galvanised steel sheet roofing

accessories of total coated thickness 0.50mm (base metal of

minimum 0.45mm thickness with total coating thickness of

12.51 0.05mm) with Zinc coating 120 grams per sqm as per IS: 277, in

240 mpa steel grade, 5-7 microns epoxy primer on both side of the

sheet and polyester top coat 15-18 microns using self drilling/ self

tapping screws complete:

84 12.51.2 Flashings/ Aprons.( Upto 600 mm) meter 25.51 519.74 13,256.20

85 12.51.3 North light curves meter 25.56 584.49 14,938.71

87 12.51.6 Gutter (600 mm over all girth) meter 25.36 1406.05 35,660.26

13.1 12 mm cement plaster of mix :

15 mm cement plaster on the rough side of single or half brick wall

13.16 6 mm cement plaster of mix : -

91 13.18 Neat cement punning sqm 150.00 85.57 12,835.57

Rough cast plaster upto 10 m height above ground level with a

mixture of sand and gravel or crushed stone from 6 mm to 10 mm

nominal size, dashed over and including the fresh plaster in two

13.19 layers, under layer 12mm cement plaster 1:4 (1 cement: 4 coarse

sand) and top layer 10 mm cement plaster 1:3 (1 cement: 3 fine

sand) mixed with 10% finely grounded hydrated lime by volume of

92 13.19.1 Ordinary cement finish using ordinary cement sqm 2500.00 948.93 23,72,319.95

Extra for providing and mixing water proofing material in cement per bag of

plaster work in proportion recommended by the manufacturers. 50KG Cement

Finishing walls with textured exterior paint of required shade :

New work (Two or more coats applied @ 3.28 ltr/10 sqm) over

94 13.45.1 and including priming coat of exterior primer applied @2.20kg/10 sqm 70.00 239.32 16,752.34

13.50 Applying priming coat :

With ready mixed aluminium primer of approved brand and

manufacture on resinous wood and plywood.

With ready mixed red oxide zinc chromate primer of approved

96 13.50.3 brand and manufacture on steel galvanised iron/steel works sqm 4500.00 72.14 3,24,621.99

Providing and applying white cement based putty 1mm on plaster

Wall painting with premium acrylic emulsion paint of interior

grade, having VOC (Volatile Organic Compound ) content less than

13.83 50 grams/ litre. of approved brand and manufacture, including

applying additional coats wherever required to achieve even

shade and colour.

DSR 2023 AMOUNT

SL NO ITEM DESCRIPTION UNIT QTY Rate AMOUNT (DSR)

Ref No. (NON DSR)

Applying priming coats with primer of approved brand and

13.85 manufacture, having low VOC (Volatile Organic Compound )

With water thinnable cement primer on wall surface having VOC

content less than 50 grams/litre.

Removing white or colour wash by scrapping and sand papering

13.88 and preparing the surface smooth including necessary repairs to sqm 47510.20 21.14 10,04,290.85

scratches etc. complete

Painting with synthetic enamel paint of approved brand and

100 13.99.1 manufacture of required colour to give an even shade : One or sqm 17163.87 110.03 18,88,486.61

more coats on old work

Repairs to plaster of thickness 12 mm to 20 mm in patches of area

2.5 sq.meters and under, including cutting the patch in proper

shape, raking out joints and preparing and plastering the surface

101 14.1.1. of the walls complete, including disposal of rubbish to the sqm 500.00 585.88 2,92,941.11

dumping ground, all complete as per direction of Engineer in-

With cement mortar 1:4 (1 cement : 4 fine sand)

Fixing chowkhats in existing opening including embedding

chowkhats in floors or walls cutting masonry for holdfasts,

embedding hold fasts in cement concrete blocks of size 15 x 10 x

10 cm with cement concrete 1:3:6 (1 cement : 3 coarse sand : 6

14.2 graded stone aggregate 20 mm nominal size), painting two coats

of approved wood preservative to sides of chowkhats and making

good the damages to walls and floors as required complete,

including disposal of rubbish to the dumping ground, all complete

as per directions of Engineer-In-Charge.

14.73 Providing and fixing bright finished brass casement window

104 fasteners or peg stays to windows/ ventilators with necessary kg 20.00 596.37 11,927.42

welding and machine screws etc. complete.

14.75 Repair to plaster of thickness 12mm to 20 mm in patches of area

2.5 sqm and under, including cutting the patch in proper shape,

raking out joints and preparing plastering the wall surface with

white cement based polymer modified self curing mortar,

including disposal of rubbish, all complete as per the direction of

Engineer-In- Charge.

Dismantling W.C. Pan of all sizes including disposal of dismantled

106 14.82 materials i/c malba all complete as per directions of Engineer-in each 300.00 143.53 43,058.17

Dismantling 15 to 40 mm dia G.I. pipe including stacking of

dismantled pipes (within 50 metres lead) as per direction of

Engineer in-Charge.

(a) Internal Work- Exposed on wall

Taking out existing wooden door shutter, repair by cutting,

painting etc. and refixing of repaired door shutters to existing door

108 14.85 frames, including replacement of hinges with screws, etc. as Each 2000.00 459.27 9,18,531.46

required, all complete as per the direction of the Engineer-in-

Dismantling works

Demolishing cement concrete manually/ by mechanical means

including disposal of material within 50 metres lead as per

109 15.2.2 direction of Engineer - in - charge. cum 150.00 1609.30 2,41,395.46

Nominal concrete 1:4:8 or leaner mix (i/c equivalent design mix).

Demolishing R.C.C. work manually/ by mechanical means including

stacking of steel bars and disposal of unserviceable material within

50 metres lead as per direction of Engineer - in- charge.

Demolishing brick work manually/ by mechanical means including

stacking of serviceable material and disposal of unserviceable

material within 50 metres lead as per direction of Engineer-in-

Dismantling doors, windows and clerestory windows (steel or

wood) shutter including chowkhats, architrave, holdfasts etc.

complete and stacking within 50 metres lead

Of area 3 sq. metres and below.

Dismantling tile work in floors and roofs laid in cement mortar

113 15.23.1 including stacking material within 50 metres lead. sqm 70.00 78.56 5,499.20

For thickness of tiles 10 mm to 25 mm

DSR 2023 AMOUNT

SL NO ITEM DESCRIPTION UNIT QTY Rate AMOUNT (DSR)

Ref No. (NON DSR)

Dismantling barbed wire or flexible wire rope in fencing including

making rolls and stacking within 50 metres lead

Dismantling of flushing cistern of all types (C.I./PVC/Vitrious China)

115 15.52 including stacking of useful materials near the site and disposal of each 300.00 119.93 35,978.13

unserviceable materials within 50 metres lead.

Dismantling old plaster or skirting raking out joints and cleaning

116 15.56 the surface for plaster including disposal of rubbish to the sqm 10000.00 58.49 5,84,918.95

dumping ground within 50 metres lead.

Disposal of building rubbish / malba / similar unserviceable,

dismantled or waste materials by mechanical means, including

117 15.60 loading, transporting, unloading to approved municipal dumping Cum 150.00 282.51 42,375.85

ground or as approved by Engineer-in-charge, beyond 50 m initial

lead, for all leads including all lifts involved.

16.15 Supplying at Site

R.C.C. Standards post/ struts/rails/ pales of mix 1:1.5:3 (1 cement :

1.5 coarse sand : 3 graded stone aggregate 12.5 mm nominal size)

118 16.15.1 with wooden plugs or 6mm bar nibs wherever required as per Cum 12.00 35203.45 4,22,441.42

direction of Engineer-in-charge (cost of earth works in excavation,

concrete works in foundation to be paid separately).

Welded steel wire fabric of required width having rectangular

mesh painted with two or more coats of enamel paint of approved

shade over a coat of primer (Priming & Painting to be paid for

Fencing with R.C.C. post placed at required distance, embedded in

cement concrete blocks, every 15th post, last but one end post

16.17 and corner post shall be strutted on both sides and end post one

side only, provided with horizontal lines and two diagonals of

barbed wire weighing 9.38 kg per 100 metres (minimum),

between the two posts fitted and fixed with G.I. staples on

Fencing with angle iron post placed at required distance

embedded in cement concrete blocks, every 15th post, last but

16.18 one end post and corner post shall be strutted on both sides and

end post on one side only and provided with horizontal lines and

two diagonals interwoven with horizontal wires, of barbed wire

weighing 9.38 kg per 100 m (minimum), between the two posts

Supplying at site Angle iron post & strut of required size including

122 16.19 bottom to be split and bent at right angle in opposite direction for kg 425.00 134.59 57,200.85

10 cm length and drilling holes upto 10 mm dia. etc. complete.

Providing and fixing concertina coil fencing with punched tape

concertina coil 600 mm dia 10 metre openable length ( total

length 90 m), having 50 nos rounds per 6 metre length, upto 3 m

height of wall with existing angle iron 'Y' shaped placed 2.4m or

3.00 m apart and with 9 horizontal R.B.T. reinforced barbed wire,

stud tied with G.I. staples and G.I. clips to retain horizontal,

123 16.53 including necessary bolts or G.I. barbed wire tied to angle iron, all meter 400.00 402.22 1,60,887.50

complete as per direction of Engineer-in-charge, with reinforced

barbed tape(R.B.T.) / Spring core (2.5mm thick) wire of high

tensile strength of 165 kg/ sq.mm with tape (0.52 mm thick) and

weight 43.478 gm/ metre (cost of M.S. angle, C.C. blocks shall be

paid separately)

Providing and laying 60mm thick factory made cement concrete

interlocking paver block of M -30 grade made by block making

machine with strong vibratory compaction, of approved size,

124 16.68 design & shape, laid in required colour and pattern over and sqm 750.00 1040.33 7,80,248.70

including 50mm thick compacted bed of coarse sand, filling the

joints with fine sand etc. all complete as per the direction of

Engineer-in-charge.

Aluminium works -

DSR 2023 AMOUNT

SL NO ITEM DESCRIPTION UNIT QTY Rate AMOUNT (DSR)

Ref No. (NON DSR)

Providing and fixing aluminium work for doors, windows,

ventilators and partitions with extruded built up standard tubular

sections/appropriate Z sections and other sections of approved

make conforming to IS: 733 and IS : 1285, fixed with rawl plugs

and screws or with fixing clips, or with expansion hold fasteners

including necessary filling up of gaps at junctions, at top, bottom

21.1 and sides with required PVC/neoprene felt etc. Aluminium

sections shall be smooth, rust free, straight, mitred and jointed

echanically wherever required including cleat angle, Aluminium

snap beading for glazing / paneling, C.P. brass / stainless steel

screws, all complete as per architectural drawings and the

directions of Engineer-in-charge. Glazing and paneling to be paid

for separately) :

21.1.1 For fixed portion.

Powder coated aluminium (minimum thickness of powder coating

For shutters of doors, windows & ventilators including providing

and fixing hinges/ pivots and making provision for fixing of fittings

wherever required including the cost of EPDM rubber / neoprene

gasket required (Fittings shall be paid for separately)

Powder coated aluminium (minimum thickness of powder coating

Providing and fixing glazing in aluminium door, window, ventilator

shutters and partitions etc. with EPDM rubber / neoprene gasket

etc. complete as per the architectural drawings and the directions

of engineer-in-charge . (Cost of aluminium snap beading shall be

paid in basic item):

With float glass panes of 4.0 mm thickness

Providing and laying water proofing treatment in sunken portion

of WCs, bathroom etc., by applying cement slurry mixed with

water proofing cement compound consisting of applying :

(a) First layer of slurry of cement @ 0.488 kg/sqm mixed with

water proofing cement compound @ 0.253 kg/ sqm. This layer will

be allowed to air cure for 4 hours.

(b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with

water proofing cement compound @ 0.126 kg/sqm. This layer will

be allowed to air cure for 4 hours followed with water curing for

(The rate includes preparation of surface, treatment and sealing of

all joints, corners, junctions of pipes and masonry with polymer sqm 293.02 660.43 1,93,520.94

DSR 2023 AMOUNT

SL NO ITEM DESCRIPTION UNIT QTY Rate AMOUNT (DSR)

Ref No. (NON DSR)

Repair with New Technologies

Chipping of unsound/weak concrete material from slabs, beams,

columns etc. with manual Chisel and/ or by standard power driven

percussion type or of approved make including tapering of all

129 26.28.1 edges, making square shoulders of cavities including cleaning the sqm 20.00 404.57 8,091.47

exposed concrete surface and reinforcement with wire brushes

etc. and disposal of debris for all lead and lifts all complete as per

direction of Engineer-In-Charge. 75mm average thickness

Cleaning of reinforcement from rust from the reinforcing bars to

give it a total rust free steel surface by using alkaline chemical rust

remover of approved make with paint brush and removing loose

particles after 24 hours of its application with wire brush and

thoroughly washing with water and allowing it to dry, all complete

as per direction of Engineer-In-Charge.

Providing, mixing and applying bonding coat of approved adhesive

26.31 on chipped portion of RCC as per specifications and direction of

Engineer-In-charge complete in all respect.

Epoxy bonding adhesive having coverage 2.20 sqm/kg

of approved make

Total civil works ₹ 6,00,68,138.00

Sanitary & Plumbing

Providing and fixing water closet squatting pan (Indian type

W.C.pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level

white P.V.C. flushing cistern, including flush pipe, with manually

17.1 controlled device (handle lever) conforming to IS : 7231, with all

fittings and fixtures complete, including cutting and making good

the walls and floors wherever required:

White Vitreous china Orissa pattern W.C. pan of size 580x440 mm

with integral type foot rests

Providing and fixing white vitreous china pedestal type water

closet (European type W.C. pan) with seat and lid, 10 litre low

level white P.V.C. flushing cistern, including flush pipe, with

17.2 manually controlled device (handle lever), conforming to IS : 7231,

with all fittings andfixtures complete, including cutting and making

good the walls and floors wherever required :

134 17.2.1 W.C. pan with ISI marked white solid plastic seat and lid Nos 60.00 6973.59 4,18,415.59

17.8 Providing and fixing white vitreous china pedestal for wash basin

135 completely recessed at the back for the reception of pipes and Nos 70.00 1801.69 1,26,118.27

Providing and fixing CP Brass 32 mm size Bottle Trap of approved

quality & make and as per the direction of Engineer-in-charge.

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as

per IS:13983 with C.I. brackets and stainless steel plug 40 mm,

including painting of fittings and brackets, cutting and making

good the walls wherever required:

17.10.1 Kitchen sink with drain board

17.10.2 Kitchen sink without drain board

17.13 Providing and fixing white vitreous china water closet squatting

pan (Indian type) :

139 17.13.2 Orissa pattern W.C. pan of size 580x440 mm Nos 65.00 3391.83 2,20,469.22

17.15 Providing and fixing white vitreous china pedestal type (European

type/ wash down type) water closet pan.

17.16A Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto

1 metre long with S.S. triangular plate to Eureopean type W.C. of

quality and make as approved by Engineer - in - charge.

17.17 Providing and fixing a pair of white vitreous china foot rests of

standard pattern for squatting pan water closet :

DSR 2023 AMOUNT

SL NO ITEM DESCRIPTION UNIT QTY Rate AMOUNT (DSR)

Ref No. (NON DSR)

17.18 Providing and fixing P.V.C. low level flushing cistern with manually

controlled device (handle lever) conforming to IS : 7231, with all

fittings and fixtures complete.

17.20 Providing and fixing solid plastic seat with lid for pedestal type

W.C. pan complete :

144 17.20.1 White solid plastic seat with lid Nos 60.00 732.99 43,979.70

17.25 Providing and fixing white vitreous china wash basin including

making all connections but excluding the cost of fittings :

145 17.25.1 Flat back wash basin of size 630x450 mm. Nos 60.00 1433.88 86,032.85

146 17.25.2 Flat back wash basin of size 550x400 mm. Nos 250.00 1062.38 2,65,594.95

147 17.25.3 Angle back wash basin of size 600x480 mm. Nos 5.00 1433.88 7,169.40

148 17.25.4 Angle back wash basin of size 400x400mm. Nos 5.00 931.43 4,657.14

149 17.25.5 Flat back wash basin of size 450x300 mm. Nos 5.00 671.08 3,355.39

17.28 Providing and fixing P.V.C. waste pipe for sink or wash basin

including P.V.C. waste fittings complete.

17.28.2 Flexible pipe

17.29 Providing and fixing 100 mm sand cast Iron grating for gully trap.

17.31 Providing and fixing 600x450 mm beveled edge mirror of superior

glass (of approved quality) complete with 6 mm thick hard board

ground fixed to wooden cleats with C.P. brass screws and washers

Providing and fixing mirror of superior glass (of approved quality)

and of required shape and size with plastic moulded frame of

approved make and shade with 6 mm thick hard board backing :

Rectangular shape 453x357 mm

17.33 Providing and fixing 600x120x5 mm glass shelf with edges round

off, supported on anodised aluminium angle frame with C.P. brass

brackets and guard rail complete fixed with 40 mm long screws,

rawl plugs etc., complete.

Providing and fixing trap of self cleansing design with screwed

down or hinged grating with or without vent arm complete,

including cost of cutting and making good the walls and floors :100

mm inlet and 100 mm outlet Sand Cast Iron S&S as per IS: 1729

17.69 Providing and fixing PTMT Waste Coupling for wash basin and sink,

of approved quality and colour.

17.69.1 Waste coupling 31 mm dia of 79 mm length and 62 mm breadth

weighing not less than 45 gms.

17.70 Providing and fixing PTMT Bottle Trap for Wash basin and sink.

17.70.1 Bottle trap 31mm single piece moulded with height of 270 mm,

effective length of tail pipe 260 mm from the centre of the waste

coupling, 77 mm breadth with 25 mm minimum water seal,

weighing not less than 260 gms

17.71 Providing and fixing PTMT liquid soap container 109 mm wide, 125

mm high and 112 mm distance from wall of standard shape with

158 bracket of the same materials with snap fittings of approved Nos 350.00 180.19 63,064.75

quality and colour, weighing not less than 105 gms.

17.72 Providing and fixing PTMT towel ring trapezoidal shape 215 mm

long, 200 mm wide with minimum distances of 37 mm from wall

face with concealed fittings arrangement of approved quality and

colour, weighing not less than 88 gms.

17.73 Providing and fixing PTMT towel rail complete with brackets fixed

to wooden cleats with CP brass screws with concealed fittings

arrangement of approved quality and colour.

17.73.1 450 mm long towel rail with total length of 495 mm, 78 mm wide

160 and effective height of 88 mm, weighing not less than 170 gms. Nos 130.00 720.74 93,696.20

Providing and fixing CPVC pipes having thermal stability for hot

and cold water supply including all CPVC plain and brass threaded

fittings including fixing the pipe with clamps at 1.00 mt spacing.

18.8 this includes jionting of pipes and fittings with one step CPVC

solvent cement and the cost of cutting chases and making good

the wall same including testing of joints complete as per the

direction of engineer incharge

concealed work including cutting chases and making good the wall

15 mm nominal outer dia pipes

162 18.8.2 20 mm nominal outer dia pipes rmt 240.00 575.39 1,38,094.39

DSR 2023 AMOUNT

SL NO ITEM DESCRIPTION UNIT QTY Rate AMOUNT (DSR)

Ref No. (NON DSR)

163 18.8.3 25 mm nominal outer dia .Pipes. rmt 75.00 671.37 50,352.53

164 18.8.4 32 mm nominal outer dia .Pipes. rmt 10.00 791.27 7,912.73

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,

having thermal stability for hot & cold water supply including all

CPVC plain & brass threaded fittings. This includes jointing of pipes

18.9 & fittings with one step CPVC solvent cement, trenching, refilling &

testing of joints complete as per direction of Engineer in Charge :

165 18.9.1 15 mm nominal dia Pipes rmt 5.00 261.90 1,309.51

168 18.9.4 32 mm nominal dia Pipes rmt 5.00 469.22 2,346.10

Providing and fixing ball valve (brass) of approved quality, High or

low pressure, with plastic floats complete :

18.21 Providing and fixing uplasticised PVC connection pipe with brass

18.21.1 30 cm length

18.21.2 45 cm length

Providing and placing on terrace (at all floor levels) polyethylene

water storage tank, IS : 12701 marked, with cover and suitable

174 18.48 locking arrangement and making necessary holes for inlet, outlet ltr 52909.09 11.77 6,22,914.60

and overflow pipes but without fittings and the base support for

18.49 Providing and fixing C.P. brass bib cock of approved quality

conforming to IS:8931:

18.54 Providing and fixing PTMT bib cock of approved quality and colour.

18.54.3 15 mm nominal bore, 165 mm long. Weighing not less than 110

18.55 Providing and fixing PTMT stop cock of approved quality and

18.55.1 15 mm nominal bore, 86 mm long. Weighing not less than 88 gms.

18.56 Providing and fixing PTMT pillar cock of approved quality and

18.56.2 15mm nominal bore, 125 mm long foam flow. Weighing not less

Providing and fixing C.P. brass long body bib cock of approved

quality conforming to IS standards and weighing not less than 690

15mm nominal bore

Providing and fixing C.P. brass angle valve for basin mixer and

180 18.53.1 geyser points of approved quality conforming to IS 8931 a) 15 mm Each 350.00 614.67 2,15,135.65

Providing and fixing CP Brass shower rose with 15 or 20 mm inlet,

150 mm diameter

Dismantling old C.I. pipes including excavation and refilling

trenches after taking out the pipes, breaking lead caulked joints,

18.82 melting of lead and making into blocks including stacking of pipes

at site lead upto 50 metre:

Total Sanitary & plumbing works 84,07,315.94

Non-schedule - Civil

Removal and cleaning of one or more vegetation/ plants from

walls roofs, chajja etc.up to 4 sqm area, chemically treatment of

183 MR surface to prevent further growth, and making good the surface nos 100.00 704.28 70,428

by plaster , grouting ,waterproofing , etc. as the case may be

including necessary scaffolding staging etc.

Non Schedule Items- Plumbing

DSR 2023 AMOUNT

SL NO ITEM DESCRIPTION UNIT QTY Rate AMOUNT (DSR)

Ref No. (NON DSR)

Supply, installation , testing commissioning of PP Mineral filled

low noise Soil & Waste system as per EN 12056, with

density 1.9 g/cm3. PP mineral(Astolan) filled Low noise system

should has a fire classification DIN 4102-B2/EN13501 .

Product should have a chemical resistance of pH 2-12 and is a

complete sound protection system according to DIN 4109.

including with push fit rubber ring sockets all necessary

fittings and specials such as Bends, junctions, offsets & vent

cowl. Fixing at wall/ceiling level supported by rubber line

bracket & hangers etc. duly epoxy coated. Cutting,

chases/holes in floors / walls / slab.Compliant with LABC.

Weight mass per unit area of DN100MM should not be less

than 110.07kg/m3. sound levels of not more than 15dBA as per

EN 14366 at a flow rate of 4 l/s.including all core cut ,chases

,cutting making holes in all wall and floor as required complete

in all respect.

Providing Fixing straight /offset type single body push fit type WC pan

connector with factory supplied spring loaded seal guard with

188 NS integral single mould sealing fins made of flexible EVA body, 10.00 800.00 8,000.00

including bush/adaptor as supplied with the pan connector (if

required). Each

Providing and fixing floor drain (FD) with 50mm/40mm outlet and

189 NS one 40mm inlet for waste, with SS grating (adjustable height), 10.00 1655.00 16,550.00

having 50mm water seal and in-built NRV

Providing and fixing PP/UPVC trap of self cleansing design with

screwed down or hinged grating with or without vent arm complete,

including cost of cutting and making good the walls and floors :

100 mm inlet and 100 mm outlet

190 NS Sand cast iron S&S as per IS: 3989 Each 10.00 1655.00 16,550.00

Providing and fixing PP/ UPVC grating with Cockroach proof

strainer of approved design including setting in floor with

cement motor to match with floor finish as per architect

requirement suitable for waster and FT.

Providing and fixing PP/UPVC brass grating with frame of

approved design including setting in floor with cement motor to

match with floor finish as per architect requirement.

Providing and fixing PP/UPVC extention piece for 100 mm dia

floor trap formed out of main pipe with multiple side inlets,

193 NS suitable for various dia pipes including all fixtures as required 20.00 1655.00 33,100.00

complete as per drawing approved sample and direction of

engineer in charge. Each

Providing and fixing Jaguar make ARI-39041 or equivalent Two Each

194 NS way bib cock with wall flange as per direction of E/I 100.00 1868.07 1,86,806.54

Providing and fixing Jaguar Make COP-057PM or equivalent C.P. Each

195 NS angular valve as per direction of E/I 10.00 881.08 8,810.81

Providing and fixing ESSCO make MQT-514 FKN or equivalent Each

196 NS Concealed Stop cock 20mm as per direction of E/I 70.00 1173.35 82,134.45

Providing and fixing Jaguar make COP-273PM or equivalent Short Each

197 NS body bib cock as per direction of E/I 10.00 1195.78 11,957.81

Providing and fixing Jaguar make OHS-1989 or equivalent Each

198 NS Overhead shower as per direction of E/I 10.00 1407.90 14,078.96

Providing and fixing Jaguar make ALD-573 B138 or equivalent Each

199 NS Health Faucet as per direction of E/I 90.00 1482.11 1,33,390.30

Providing and fixing Jaguar make ACN-1111SM Towel rail or Each

200 NS equivalent 600 mm long as per direction of E/I 150.00 1661.42 2,49,213.62

Providing and fixing Jaguar make AHS-1551 or equivalent Toilet Each

201 NS paper Holder as per direction of E/I 10.00 1495.43 14,954.31

Providing and fixing Jaguar make CAN-1161N or equivalent Each

202 NS Double coat hook as per direction of E/I 10.00 657.99 6,579.90

Providing and fixing Jaguar make SDR-WHT-DJ0010F or Each

203 NS equivalent Soap Container as per direction of E/I 150.00 1638.99 2,45,848.90

Providing and fixing Jaguar make CNS-WHT-705 or equivalent Each

204 NS Under Counter basin as per direction of E/I 10.00 3042.02 30,420.19

DSR 2023 AMOUNT

SL NO ITEM DESCRIPTION UNIT QTY Rate AMOUNT (DSR)

Ref No. (NON DSR)

Providing and fixing Jaguar or equivalent make Pillar cock as per Each

Providing and fixing Jaguar ESSCO or equivalent Waste coupling Each

206 NS as per direction of E/I 10.00 548.57 5,485.67

Total of the Sub-Head -Plumbing NS

Total NS Plumbing 15,88,739