PROVISION OF TRAINING SHED FOR 13 PARA (SF), TOILET BLOCK FOR JCOs SINGLE LIVING WITH ALLIED INFRA NEAR MT AREA AT HEBBAL GARRISON UNDER GE (NORTH) BANGALORE

Excavation in trenches not exc 1.5 mtr depth & not exc 1.5 m deep and getting out in Hard/Dense soil all as specified & directed

Excavation in trenches not exc 1.5mtr wide and depth exc 1.5 m but not exc 3m deep and getting out Hard/Dense Soil all as specified & directed

M&L for Plain Cement Concrete (1:4:8) type D-2 using 40mm graded stone aggregate in foundations, filling and mass concrete all as specified & directed

M&L for Reinforced Cement Concrete Design mix M-25 grade using 20mm graded stone aggregate in Foundations footings, plinth beams, bases for columns, etc all as specified & directed

M&L for Reinforced Cement Concrete Design mix M-25 grade using 20mm graded stone aggregate above top of footings including attached pilasters and buttresses all as specified & directed

M&L for Reinforced Cement Concrete Design mix M-25 grade using 20mm graded stone aggregate in Columns, pillars, piers, posts and struts all as specified & directed

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm thick all as specified & directed

Removing excavated soil to a distance exc 1.50 km but not exc 5 km and depositing where directed all as specified & directed

M&L for Formwork to sides of concrete foundations, footings, bases of columns, and plinth beams and similar work vertical or to batter finished fair flat surfaces all as specified & directed

M&L for Formwork to sides of pillars, posts, struts, piers, columns and stanchions finished fair square, rectangular surfaces all as specified & directed

M&L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips all as specified & directed

M&L for Mild steel TMT bars 5mm dia and over upto 10mm bars as in stirrups, spacers, binders, cut to length, bent to shape required, including cranking binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips all as specified & directed

M&L for Pre-cast cement concrete (1:3:6) type C-1 using 20mm graded stone aggregate as in solid block masonary exceeding 10cm in width setting in cement mortar (1:6) complete all as specified & directed

M&L for rendering 15mm thick cement mortar (1 :4) mixed with WPC on concrete surfaces of roof slab and parapets mixed with WPC all as specified and directed (Note : WPC shall be measured and paid separetely)

Earth filling under floors or in foundations including watering and consolidation etc complete all as specified and directed

M&L for Hardcore of gauge not exc 63mm, deposited, spread and levelled in layers n exc. 15cm thick, watered and rammed to a true surface complete all as specified and directed

M&L for Plain Cement Concrete (1:4:8) type D-2 using 40mm graded stone aggregate as in 75mm thick sub base to floor complete all as specified and as directed.

M & L for Plain Cement Concrete (1:2:4) type B-1 using 20mm graded stone aggregate as in 40mm thick flooring finishing surface even and smooth without using extra cement complete all as specified and as directed.

M&L for preparations of new plastered wall surfaces and applying three coats of white wash complete all as specified and as directed.

S & F Rolled mild steel Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, with riveted, bolted or welded attachment, conforming to Fe-410- W(Gde- E-250) quality B complete all as specified and as directed.

S & F Rolled mild steel work in Compound girders and stanchions, lattice girders, aerial masts, staging for water tanks and the like including caps, bases, splices etc. built up from two or more beam or channel sections or angles with plates, including all lattice bars, stiffeners, gusset plates, etc Fe-410- W(Gde- E-250) quality B complete all as specified and as directed.

S & F Steel work in Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. Fe 410 -W (Gde- E- 250) quality- A complete all as specified and as directed.

M & L for Preparation of new or previously untreated steel surfaces exceeding 10cm width or girth not otherwise described & applying a two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed.

M & L for Pre - painted galvatume aluminum zinc coating, 150 AZ, GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws all as specified and as directed.

S & F Pre-painted galvalume aluminum zinc coating, 150 AZ, GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws all as specified and as directed.

Material and Labour for plain cement concrete (1:3:6) type C-1 using 20mm graded stone aggregate as in 75 mm thick paving / plinth protection laid in panels including necessary form work, complete all as specified and directed

Excavation over areas not exc 1.50m deep and getting out in Soft/Loose soil complete all as specified and directed

Removing excavated soil to a distance exc. 250 m but not exc. 500 m and depositing where directed complete all as specified and directed

M & L for Plain Cement Concrete (1:4:8) type D-2, using 40mm graded stone aggregate as in 100 mm thick in sub-base concrete to pavement complete all as specified and directed

M & L for Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and directed

M & L for Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand; all as specified and directed

Surface excavation not exc 30 cm deep and averaging 15 cm deep and getting out hard dense soil all as specified & directed.

Removing excavated soil to a distance exc. 1.50 km but not exc. 5 km and depositing where directed all as specified & directed.

M&L for Reinforced cement concrete Design mix M-25 grade using 20mm graded stone aggregate as in Beams, cantilevers, bressummers, lintels over 1.5m span all as specified & directed.

M&L for Reinforced cement concrete Design mix M-25 grade using 20mm graded stone aggregate as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like all as specified & directed.

M&L for Reinforced cement concrete Design mix M-25 grade using 20mm graded stone aggregate as in chajjas all as specified & directed.

M&L for Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelvesincluding sup- ports, overhangs, etc. also splays between floors and beams, etc. finished fair flat surfaces all as specified & directed.

M&L for Formwork to suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) finished fair flat surfaces all as specified & directed.

M&L for Formwork to edges of concrete flats, treads, breaks in floors, window-cills, concrete railing, openings in concrete walls, floor and roofs not exc 20cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10 cm but not exc 20 cm wide in rough finished flat surfaces of concrete all as specified & directed.

M&L for Formwork to chullah hoods, chajjas, troughs and similar items including edges rough finished flat surfaces all as specified & directed

M& L for water proofing treatment over RCC roof slab with the following specification all as specified & directed :- (i) Cleaning existing surface properly (ii) Screed bed 15mm thick in CM (1:3) mixed with and including supply of approved water proofing compound as per manufacturers instructions, finished smooth surfaces (iii) Apply oil bound bitumen primer @ 0.40 lit/Sqm manufactured by the same agency as that of APP with a density o 0.87-0.89 Kg/Lit at 25º C on the prepared dry roof surface., providing and laying APP modified water proofing membrane 3mm thick reinforced with non woven polyester matt with physical prosperities as under:- (a) Membrane weight>3.8 Kg/ sqm (b) Non woven polyester weight>160 gm/Sqm (c) Softening point of membrane >150º C (d) Joint tensile strength longitudinal >650 Sqm Cm at 230º C & Transverse> 450/Sq Cm (e) Tear strength - longitudinal >300N & Transverse>250 N Direction (f) Elongation > 30 % (g) Impermeability under water pressure > 3 Kg/Sq cm (iv) Applying a coat of solar reflective bituminous aluminium paint @ 0.10 litre/sqm

M&L for Pre-cast cement concrete (1:3:6) type C-1 using 20mm graded stone aggregate as in solid block masonary not exceeding 10cm in width setting in cement mortar ( 1:4) complete all as specified and as directed

M&L for 15mm thick rendering in two layers i.e., 10mm thick backing coat in CM (1:6) and 5mm thick floating coat in CM (1:4) mixed with water proofing compound on all external wall surfaces all as specified and as directed (Note : WPC will be measured & paid seperately)

Supply only liquid water proofing compound, ISI marked, all as specified and as directed

M&L for 10mm thick rendering in cement mortar ( 1:6) on brick or concrete wall surfaces finished even & smooth all as specified and as directed

M&L for rendering 5mm thick in cement mortar (1:3) on soffits of RCC slabs, roof projections, soffits and sides of RCC beams, waist slab, Loft Slab, RCC shelves, Chajjas, and the like all as specified and as directed.

Material and labor for PCC (1:2:4) type B-1 using 20mm graded stone aggregate as in 40 mm thick in ramp, finishing cement concrete surface even and fair without using extra cement etc., all as specified and as directed.

Material and labor for PCC (1:2:4) type B-1 using 20mm graded stone aggregate as in 25 mm thick in flooring finishing cement concrete surface even and fair without using extra cement etc all as specified and as directed.

M&L for Plain Cement concrete (1:3:6) type C2 using 40mm graded stone aggregate as in 75mm thick plinth protection finished even & smooth without using extra cement and joint filling with sealing compound Grade ‘A’ all as specified and as directed.

M&L for PCC 1:2:4 Type B0 using 12.5 mm graded stone aggregate as in coping, as in hold fast block, filling in steel frame of window, in roof kerbs of mud stops, rounded or chamfered on edges cills, steps etc; all as specified and directed.

M & L for Non Skid ceramic coloured tiles 7 to 8 mm thick , (square / rectangular) area of each tiles exc 0.11 Sqm but not exc 0.18 Sqm as in floors etc, over & including screed bed or bedding layer of 15 mm thick cement mortar (1:6) for laying floor finishes set and jointed in neat cement slurry and pointed with white or coloured cement to match etc complete all as specified and as directed

M&L for Glazed ceramic coloured tiles 350mmx 250mmx 7mm / 450mm x 350mm x 7 mm thick as in skirting / dado, set and jointed in neat cement slurry and pointed in white or colour cement to match etc complete all as specified and and as directed

S & F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification and as directed

S & F Solid PVC Door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification and as directed

S & F Butt hinges medium weight, cold rolled mild steel 100mm long and fixed to door frame and shutter duly welded/screwed complete all as specified and as directed

S & F Aluminium anodized barrel tower bolt of extruded section of size 125mm long complete all as specified and directed.

S & F Extruded Aluminum handles 150mm size, fabricated type, anodised all as specified

M&L for Granite slab 18/20mm thick (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite all as specified and directed.

S&F Rotational moulded polythylene water storage tanks 1000 ltrs capacity, triple layered, (cylindrical or vertical with closed top) hoisted and fixed in position, complete all as specified and directed.

S&F Vitreous china water closet, pedestal type, white including connection to flush pipe, seat cover etc, connection to drain (or out going pipe) and to flushing pipe anti syphonage pipes etc complete all as specified and as directed.

S&F Vitreous china squatting pan "Orissa" Pattern, size 580 x 440 mm etc, including connection to drain (or out going pipe) and to flushing pipe anti syphonage pipes etc complete all as specified and as directed.

S & F Wash basins, Vitreous China (flat back or angle back type) size 550x400, including cutting for and pinning in ends of brackets or erecting stand all as specified and as directed.

S & F Vitreous China Urinal, Half stall type, white including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement all as specified and as directed.

S&F PVC low level flushing cistern,10 litres capacity, PVC valveless, syphonic action type, white, with inlet, ball valve, float and handle including brackets including PVC connection 300 mm long with PTMT nuts and other accessories, fixed to 15mm dia bore pipes complete all as specified and directed.

S&F PVC (SWR) Pipe 110 mm dia bore single socketed in any length with rubber ring joint laid in trenches/fixed on floor/walls including jointing with solvent cement all as specified and directed.

S&F PVC (SWR) bends 110 mm dia with access door any radius complete all as specified and directed

S&F PVC (SWR) junction single 110 mm dia, (Single T) equal or unequal complete all as specified and directed

S&F PVC (SWR) vent cowl 110 mm dia complete all as specified and directed

S&F PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and directed.

S&F Towel Rail 600mm long of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 190gms) complete all as specified and directed.

S & F Soap dish, vitreous China white, approximate size 160x 160x90mm embedded in the wall complete all as specified & directed

Supplying and laying CPVC pipes 25mm outer dia SDR 11 & Plain CPVC SDR 11 fittings fixed to walls, ceilings or in floors etc.,complete all as specified & directed.

Supplying and laying concealed CPVC pipes 20mm outer dia SDR 11 & Plain CPVC SDR 11 fittings in to walls concealed complete all as specified & directed. (Note : Quoted rate deemed to be included cutting into wall for concealing pipe, filling cement mortar, making good etc)

Supplying and fixing of Brass Elbow 25mm dia bore complete all as specified & directed

Supplying and fixing of Brass Tee 25mm dia bore complete all as specified & directed

Supplying and fixing of 20mm dia Brass Elbow complete all as specified & directed

Supplying and fixing of 20mm dia Brass Tee complete all as specified & directed

Supplying and fixing of CPVC BALL VALVE suitable for 25mm dia pipe complete all as specified & directed

S & F in repairs fancy type pillar tap cast copper alloy with capstan heads chromium plated screwed down high pressure with long screwed shanks and fly nuts screwed for iron pipes 15 mm bore all as specified and directed.

S & F Fancy type chromium plated Bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe 15 mm bore or for brass ferrule and fixed all as specified and directed.

S & F Fancy type, chromium plated with long shank and cup (concealed type) Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe 15 mm bore or for unions and fixed all as specified and directed.

S & F Fancy type, chromium plated Stop valves/angle valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle,screwed both ends for iron pipe 15 mm bore or for unions and fixed all as specified and directed.

S & F PVC waste pipe 32mm dia, for WHB, urinal etc, complete all as specified and as directed.

S & F PVC connections 15mm dia with PTMT nuts of length 600mm complete all as specified and as directed.

M&L for rendering 10 mm thick in cement mortar 1:3 on fair faces of brick work or concrete surface as backing coat coat of dado/skirting etc complete all as specified and as directed

M&L for preparation of newly plastered surfaces of walls and applying two coat of cement base paint, including one coat of white washing primer complete all as specified and as directed.

M & L for Preparation of newly plastered surfaces of wall and applying two coats of Acrylic emulsion distemper over a coat of alkali resistant primer complete all as specificed and as directed

M & L for Preperation of newly plastered surfaces of Ceilings, soffits of RCC slabs, roof projections, soffits and sides of RCC beams, waist slab, Loft Slab, RCC shelves, Chajjas, and the like applying three coats of of white wash complete all as specificed and as directed

S&F Mild steel framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, Doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive or steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing, conforming to Fe- 290 (Gde E-165) complete all as specificed and as directed

M& L for Mild steel, plain black sheet 1 mm thick in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required

S&F Steel windows/ Ventilitors with side hung shutter without glazing bar including projecting type hinges with steel handle, and steel peg stay, dovetailed or welded complete all as specified and as directed

Supply and fix Sheet glass 4mm thick ordinary quality and glazing with rubber packing around the glass, in squares not exc 0.5 Sqm in each pane complete all as specified and as directed.

M & L for Mild steel framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work as in ornamental type gate conforming to Fe.290.Gde-E-165 complete all as specified and as directed.

Excavation over areas not exc 1.50m deep and getting out in hard / dense soil complete all as specified and directed

M & L for PCC (1:4:8) type D-2 using 40mm graded stone aggregate as in surface channel all as specified and directed

M&L for rendering 15mm thick cement mortar (1:4) mixed with water proofing compound as per manufactures instructions on fair faces of brick work or concrete block walling surfaces finished even and smooth without using extra cement all as specified and directed. (Note : WPC willbe measured seperately)

Removing the excavated soil to a distance not exc 50m and depositing where directed at a level not exc 1.5m high from the starting point all as specified and directed.

M&L for Plain cement concrete (1:2:4) type B1 using 20 mm graded stone aggregate as in coping, benching of manholes and similar work etc complete all as specified and directed.

M & L for Precast Reinforced cement concrete (1:2:4) type B1 using 20mm graded stone aggregate as in cover slab for man hole set in cement mortar (1:4) all as specified and directed.

M & L for Mild steel TMT bars 8 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips all as specified and directed.

Excavation over areas exc 1.50m but not exc 3m deep and getting out in hard / dense soil complete all as specified and directed

M & L for Plain cement concrete (1:4:8), type D2 using 40 mm graded stone aggregate as in concrete bed to drain pipes 200 mm dia bore including packing under and haunching against the side of DWCP pipes after they are laid and tested complete all as specified and as directed

M & L for Double wall corrugated polyethelene pipes (DWCPE pipes) 200 mm dia, class SN-8 conforming to IS 16098 (part-2) in 6 mtr length laid in trenches with couplers complete all as specified and as directed

M&L for Plain cement concrete (1:2:4) type B1 (using 20 mm graded stone agg) as in coping, benching of manholes and similar work etc complete.

M&L for plain Cement concrete (1:2:4) type B2 (using 20 mm graded stone agg) in surface channels and drains complete all as specified and as directed

M & L for Point Wiring with single core PVC insulated unsheathed 1.5 Sqmm cable 1100 volts grade multi stranded copper conductor drawn through & including PVC rigid non metallic conduit ISI marked fixed with all fittings and all accesories, surface type on walls/roof /truss including suitable sunken box frame and cover, frame plate for mounting of switches/sockets as required, including 1.5 Sqmm PVC insulated single core multi stranded copper conductor cable as earth continuity conductor and connecting to common earth dolly, all as specified and as directed for the following :-

One light point controlled by one switch

One fan/exhaust point controlled by one switch/regulator

One 3 pin socket out let 5 A on same board

One 3 pin socket out let 5 Amps on independent board

All as per item No 108 here-in-before but point wiring with 2.5 Sqmm PVC insulated unsheathed copper conductor on independent board including 2.5 Sqmm PVC insulated solid copper conductor contineous earth wire for 16 Amps socket outlet Note for Item No 107 & 108 :- (i) The earth wire for the points in the same circuit can be looped from point to point (ii) Earth wire shall be taken inside the conduit (iii) Cost of terminal box is deemed to be included in the item rate quoted for point wiring (iv) Cost of a circuit of any length of cable from DB to any switch/ socket board to be included in point wiring.

S&F LED batten with luminaire suitable for indoor applications 18/20 Watts, 4 feet long with extruded aluminium housing & integrated LED channel rectangular white arcylic cover complete with hanging provision accessories all as specified and directed.

S&F Switch piano flush type, single pole, one way 5 Amps, 230volts all as specified and directed.

S&F Switch Socket Combination 5 pin 2 in 1, 5 Amps flush type 230volts all as specified and as directed

S&F MCB SPN 240 volts 40 Amps, C curves complete all as specified and as directed

S&F MCB single pole 240 volts 6 to 32 Amps, C curves complete all as specified and as directed

S&F MCB Distribution Board SPN 8 way, double door type, 240 volts with 200 Amps rated busbar as specified and as directed.

S&F Ceiling rose, surface bakelite type 65 x 50 mm, 2 to 3 terminals all as specified and as directed

M&L for earthing with galvanized steel earth plate electrode 60 cm x 60 cm x 6mm thick buried directly in ground vertically to a depth not less than 2.25 mtr below ground level with top edge of earth plate at a depth not less than 1.5 mtr connected to galvanized earth lead wire 4 mm dia as earth lead up to 7.5 mtr long by means of nuts, bolts, thimbles,check nuts and washers etc made of galvanized iron connected to earthing test point all as shown in electrical plate No 3 of SSR Part-I and as specified or indicated and testing on completion including earth work and excavation in any type of soil, PCC (1:3:6) type C1 chamber, pre cast slab 40mm thick in cement concrete (1:2:4) type B1 with 8 mm dia MS bars reinforced at 10 cm centre to centre both ways, funnel with watering pipe, wire mesh and lugs, test point complete all as specified and as directed.

M&L for sand cushioning under and above the cable complete all as specified and as directed (Note : Punned thickness will be measured for payment)

Supply & laying sub class 'B' burnt bricks for cable protection complete as specified as directed

Supply & laying XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armouned power cables (heavy duty) with aluminium conductor, 1100 volts grade, cross sectional area 16 Sqmm, 2 core laid in trenches / wall complete as specified as directed

S&F G I tubing, light grade 32 mm dia bore with all fitting laid in trenches / walls / Roads for cable protection complete as specified as directed.

S & F Bracket made out of GI tubing medium grade 25 mm bore, approx length 1.5 m long including MS clamps made out of MS flat iron 25 x 6 mm , nuts, bolts, washers etc and including applying two coats of aluminum paint over a coat of red oxide primer complete all as specified and directed.

Supply and fixing LED bldg security light fitting 35 Watts capacity with pressure die cast housing along with prismatic polycarbonate difuser with IP 66 protection complete all as specified and directed.

M & L for Point Wiring with single core PVC insulated unsheathed 1.5 Sqmm 1100 volts grade multi stranded with FRLS copper conductor cable conforming to IS 694 drawn through and including non-metalic rigid PVC conduit medium grade ISI marked with accessories including GI / MS branded sunken boxes of suitable module concealed on walls including modular frame and cover of suitable module fixed with cadmium plated iron screws for housing modular type switches, switch socket outlets, fan regulators etc., including 1.5 Sqmm PVC insulated single core multi stranded copper conductor cable as earth continuity conductor and connecting to common earth dolly, all as specified and as directed for the following :-

One light point controlled by one switch

One fan/exhaust point controlled by one switch/regulator

One 3 pin socket out let 5 Amp on same board Note for Item No. 123 :- (i) The earth wire for the points in the same circuit can be looped from point to point (ii) Earth wire shall be taken inside the conduit (iii) Cost of terminal box & Cost of a circuit of any length of cable from DB to any switch/ socket board is deemed to be included in the quoted rate

S&F LED batten with luminaire suitable for indoor application, 10 Watts capacity 2 feet long with polycarbonate housing & integrated LED channel rectangular white arcylic cover complete with all accessories all as specified and directed.

Supply and fix Modular switch 1 way 6Amps,1 module 240 volts all as specified and directed.

Supply and fix Modular Socket, 6A - 2/3 pin combined 2 module all as specified and directed.

S&F MCB Distribution board SPN 4 way, double door type 240 volts with 200 Amps rated busbar all as specified and as directed.

S&F Exhaust Fan 200mm Sweep with blade, frame and louver, steel body heavy duty, AC single phase, 230Volts all as specified & directed.

S&F G I tubing medium grade 25 mm dia bore with all fitting laid in trenches / walls / Roads for water supply all as specified & directed.

S&F GI tubing medium grade 20 mm dia bore with all fitting laid in trenches/walls/Roads for cable protection all as specified & directed.

S&F Gun metal Gate valve with iron wheel head, screwed both ends for iron pipe 20 mm dia all as specified & directed.

S&F Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe 20mm dia or brass ferrule and fixed all as specified & directed.