GE 861 EWS-59/2024-25

Amount

Surface excavation n. exc (not exceeding) 30cm deep and averaging 15cm deep and getting out in hard/dense soil complete all as specified and directed by Engineer-in-Charge.

Excavation in trenches, n. exc 1.5m wide and n. exc 1.5m in depth, for foundations, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sqm on plan and n exc 1.5m in depth and getting out in Hard / Dense soil complete all as specified and directed by Engineer-in-Charge.

Excavation in post holes (or similar holes) each n exc 0.5 cum getting out, returning, filling in and ramming earth or broken rubble mixed with earth around in layers not exceeding 25 cm complete all as specified and directed by Engineer-in-Charge.

Returning filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in soils complete all as specified and directed by Engineer-in-Charge.

Removing excavated materials n. exc. 50 metres and depositting where directed at a level n. exc. 1.5 m above the starting point complete all as specified and directed by Engineer-in-Charge.

M&L for PCC 1:4:8 type D2 (using 40 mm graded crushed stone aggregate) as in foundations, filling and mass concrete complete all as specified and directed by Engineer-in-Charge.

M&L for PCC type C2 (1:3:6) (using 40mm graded crushed stone aggregate) as in foundations, filling and mass concrete complete all as specified and directed by Engineer-in-Charge.

M&L for Brickwork with sub class ‘B’ bricks, straight or curved on plan exc 6m mean radius for manholes/septic tank/soak well etc/ in sewer works with old size bricks built in cement mortar (1:6) complete all as specified and directed by Engineer-in-Charge.

M&L for 15mm thick rendering in cement mortar (1:4) inside and outside brick wall of manhole /septic tank /concrete surfaces even surface finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of newly plastered surfaces of walls and applying two coats of cement based paint over a coat of alkali resistant primer complete all as specified and directed by Engineer-in-Charge.

S&F mild steel work in tabular trusses and tubular post including special shaped washers etc. complete using ERW or induction butt welded tubes conforming IS:1161-1979 St-240 complete all as specified and directed by Engineer-in-Charge.

S&F mild steel plates (plain or chequered) square cut or notched (forming holes with riveted, bolted welded attachment) Fe 410-w(Grade-E-250) quality-A complete all as specified and directed by Engineer-in-Charge.

S&F roof trusses (framed), trussed, fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc., including Welding, cutting for required position conforming to Fe 410-W (Gde-E- 250) quality complete all as specified and directed by Engineer-in-Charge.

S&F Pre- painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed by Engineer-in-Charge.

S&F Pre- painted galvalume aluminium zinc coating GI based plain steel sheets 0.50mm thick of any colour having tensile strength of 550Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed by Engineer-in-Charge.

M&L for two coats synthetic enamel paint over a coat of red oxide primer on new steel surfaces including preparation of steel surfaces over 10 cm width or girth complete all as specified and directed by Engineer-in-Charge.

M&L for hard core of gauge n. exc. 63 mm, deposited, spread and levelled in layers n. exc. 15 cm thick, watered and rammed to a true surface of broken stones or boulders complete all as specified and directed by Engineer-in-Charge.

M&L for 100mm thick plain cement concrete (1:3:6) type C2 (using 40mm graded crushed stone aggregate) as in sub base of floor complete all as specified and as directed by Engr-in-Charge.

M&L for sand filling under floors or in foundations including watering and consolidation complete all as specified and directed by Engr-in-charge.

M&L for Machine pressed coloured concrete interlocking paver blocks any slope and size confirming to IS 15658-2006 of 80mm thickness M-40 Grade with grey cement and pigments fixing through vibratory compaction by using plate vibrator, filling the joint with fine sand cutting of paver block as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed by Engineer-in-Charge.

Excavating in trenches, n. exc 1.5m wide and n exc 1.5m in depth, for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sqm on plan and n exc 1.5m in depth and getting out in soft/loose soil complete all as specified and directed by Engineer-in-Charge.

M&L for setting coat of 3mm thick of cement mortar (1:2) trowelled to even and smooth finish over rendering 15mm thick in cement mortar 1:4 on fair faces of brick work finished surface even & smooth with using water proofing compound @ 2% by weight of cement complete all as specified and directed by Engineer-in-Charge.

Supply only liquid water proofing compound complete all as specified and directed by Engineer-in-Charge.

M&L for providing RCC precast cement concrete type B-0 1:2:4 mix (using 20 mm graded crushed stone aggregate) as in cover slab for manhole and similar articles with plain face set in cement mortar (1:4) complete all as specified nd directed. Note : Reinforcement shall be measured and paid separately.

S&F mild steel TMT bars 10mm and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia or securing with clip complete all as specified and directed by Engineer-in-Charge.

M&L for point wiring for one light point/fan point controlled by one switch with 2.5 sqmm PVC FRLS insulated unsheathed copper conductor single core multi strand flexible cable and 2.5 sqmm PVC FRLS insulated unsheathed copper conductor single core cable (green colour) as earth lead in and including PVC conduit medium grade of suitable size run or concluded with all fittings (ISI Marked) controlled by one switch including CI/MS/ wooden sunk box of required size & as directed by Engr-in-Charge & 3mm thick plastic laminated sheet, including cutting chases to wall making good the disturbed surfaces to match with the existing specification complete all as specified and directed by Engineer-in-Charge.

Supply & fixing sheet metal enclosure double door, single pole and neutral, AC 240 volts, 8 way with 200 Amps rated copper bus bar and IP-43 protection with metal double door and flush to wall and making good including two coats of white/ colour washing/ distempering etc to match the existing disturbed surfaces complete all as specified and directed by Engineer-in-Charge.

Supply and fixing MCB, SP, AC, 240 volts "B" series capacity of 06 to 32 Amps, 10KA and making connections complete all as specified and directed by Engineer-in-Charge.

Supply and fixing MCB, SPN (Single Pole Neutral), AC, 240 volts, "B" series capacity 32 Amps 10 KA and making connections complete all as specified and directed by Engineer-in-Charge.

Supply and fixing LED street light fitting 60 Watt 230 V AC out door type with high pressure die cast aluminium hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and directed by Engineer-in-Charge.

Supply and fixing security light brackets of GI pipe medium grade upto 1.2 mtr long bend to shape at 100-120 degree including arrangement of fixing at pole/wall/angle with the help of flat iron clamps and suitable nuts and bolts including all material required for fitting complete all as specified and directed by Engineer-in-Charge.

Supply and fixing and testing of 1100 volts grade heavy duty cable PVC insulated aluminium conductor of size 10 sqmm 2 core served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 metre apart including 4mm suspension wire, one twin core cable flat or circular all specified and directed.

BHAT CONSTRUCTIONS AND BUILFERS (BID ID -3146908)

JANDOO AND CO (BID ID -3147011)

M/S BILAL AHMAD BHAT (BID ID -3153001)