REPAIRS TO BOUNDARY WALL COMPOUND WALL FENCING GATE AT ITR TECH AREA LAUNCH COMPLEXES TRACKING STATIONS AND PLACES ALONG RANGE ROAD AT ITR CHANDIPUR UNDER AGE BR II

Amount

NOTE (Applicable for all items) :- The bidders/contractors are advised to read tender document & all corrigendum / amendments and General conditions of contracts before entrying/quoting the rates.

Dismantling wrought iron or mild steel work of any description not otherwise provided for.

Demolition of reinforced cement concrete of any description in any position not otherwise specifically provided for.

Demolition of brick work or stone/boulder masonry, built in lime mortar including all quoins, arches,pillars, rtc., but excluding ashlar facings, dressed stonework and precast concrete articles built in cement mortar.

Demoition Concrete in ground floors and pavings n exc 15 cm thick (below or above ground level).

Dismantling Fencing wire mesh, any type.

Dismantling posts or struts (wood, steel or RCC) any section, incl taking out embedded any position and making good disturbed in ground or PCC.

Taking down cement plaster on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and as directed.

Excavating in post holes in soft / loose soil not exc. 0.5 cum all as specified

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc1.5 m in depth and getting out in soft/loose soil.

M&L Moorum/red bajri filling in floors or pavings, laid in layers n exc 15 cm thick, spread, levelled and blinded with earth and rammed incl watering.

M&L PCC 1:4:8 type D-2 (using 40 mm graded stone aggregate) as in foundation filing and mass concrete

M&L for RCC M-30 design mix with using 20mm graded stone agg as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc; basement slabs, under-reamed piles and mass concrete.

M&L for RCC M-30 design mix with using 20mm graded stone agg as in columns, pillars, piers, posts and struts.

M&L for RCC M-30 design mix with using 20mm graded stone agg as in beams, cantilevers, bressummers, lintels over 1.5m span.slabs etc

Formwork to sides of rough finished flat surfaces of concrete pillars, posts, struts, piers, columns, and stanchions fair finished surfaces of concrete in square, rectangular etc all as specified and directed.

Formwork to sides of rough finished surface of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work complete

Formwork to sides and soffits of rough finish surfaces of concrete floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, fair finished surface complete

M&L MS TMT bars (Fe 500D) 10 mm and above, cut to length ,bent to shape required, including cranking, bending, spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips as in reinforcement

All as per Sl Item No. 18 above but 5 mm dia and over upto and incl 10 mm dia in stirrus, spaces, and binders.

M&L for brick work in flyash bricks old size, straight or curved on plan exc 6m mean radius built in cement mortar 1:4 etc complete all as specified

All as per Sl Item No 20 above but except bricks.

M&L for 15 mm thick cement plaster in CM 1:4 on brick/stone surface finished even and fair complete

M&L for Preparation of new plastered surfaces and applying two coats of cement based paint over a coat of chalk whitning all as specified and directed.

M&L for Preparation of old plastered surfaces and applying two coats of cement based paint all as specified and directed.

M&L for Preparation of old plastered surfaces and applying one coat of cement based paint all as specified and directed.

M&L for applying one coat of acrylic weather coat premium quality antifungal exterior emulsion to old painted surface of wall including preparation all as specified and directed

M&L for finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

M&L for mild steel framed work such as posts, railing and fencing work framed guard bars, barred iron doors and similar work including cutting tops to shape as directed, drilling, holes notching for wire, etc: flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc, and similar work conforming to Fe-290 Gde E-165.

Providing precast reinforced cement concrete type B1 1:2:4 (using 20mm graded aggregate) as in precast posts, fencing posts, stuts etc. for fencing, average sectional area exe 100 and n exc 250 sq.cm with or without chamfered angle and flat, splayed, rounded or mitred tops incl necessary formwork.

S&F PVC coated GI chain link fencing with 50mm x 50mm /75mm x 75mm mesh proper fixed to any type of fencing post with MS fillet and screw bolts all as specified and directed. Note : MS fillet and Screw bolts will be measured and paid separately

Refixing chain link fencing including line wires, any mesh, size and type of standards, rails, straining bolts, etc.

S&F Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other or screwed both end each screwed end to be fitted with washers and one hexagonal or square nut, exc 10 cm but n exc 15 cm long of 5 to 10 mm dia of neck.

S&F MS round bars 10mm dia for support to chain link fencing

S&F in repair Galvanised, 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacing and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossing with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed

M&L for spiral punched tape concertina coil of 600 dia and 6 m max openable length, fixed with angle iron Y shaped with G.I. staples and G.I. clips to retain horizontal, incl necessary bolts as required complete as directed by Engr-in-Charge Note : Angle iron and barbered wire shall be measured and paid separately.

M&L for preparation of new steel surfaces of any description, not exc 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer.

M&L for preparation of new surfaces of steel or iron surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer.

M&L Providing, cement concrete 1:2:4 type B-1 (using 20 mm graded stone aggregate) as in roof kerbs or mud stop, rounded or champered on edges as in coping including necessary formwork complete all as directed.

M&L for providing broken glass coping 150 mm long @ 50 mm c/c fixed on top of walls in CM 1:3.

Returning, filling in, includingspreading, levelling, ateringand well ramming in layersnot exc 25 cm in soft/loose soil.

Removing excavated material n exc 50 m and depositing where directed at a level n exc 1.5 m above the starting point for soils

M&L for precast cement concrete 1:2:4, type B-2 (using 40 mm graded stone aggregate) as in landing cover slab, chull huds similar works etc complete all as specified.

M&L Cement concrete 1:4:8 type D2 (using 40 mm graded stone aggregate), 75 mm thick as in sub base.

M&L Cement concrete work in pavement /hard-standing of flexural strength 40 kg/per square centimeter in field using 400 kg of cement per cubic metre, thickness of concrete 25 cm or less laid in panels complete all as directed.

Forming contraction Dummy joint 65mm deep and 10 mm wide with filling sealing compound grade A, as in 100 mm thick concrete slab.

Forming Construction joint 30 mm deep 10 mm wide filled with sealing compound.

S&F Rolled sections/Tubular MS pipes as in cross beams, hip and jack rafters, vertical posts, purlins where connected to commonn rafters fixed with angle cleats or other connecting plates including welding and all necessery works complete all as specified

S&F in repair Pre-laminated galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of colour having tensile strength of 550 Mpa as iin roof covering/cladding to wall, fixed with self tapping screws including dismantling all as specified

All as per Sl Item No. 48 above but plain steel sheet as in ridges & vally gutters

S & F Framed work such as grills, gratings, framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165

M&L for providing and fixing stainless steel (Grade 316) railing /grill gate and similar work made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing/gate with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, complete

M/S T.N.CONSTRUCTION

M/SNeelachal Enterprises

RANA ENTERPRISES

vaishnaveedevienterprises

MS SUBHAM ENGINEERING AND CO

M/s R.C REFRIGERATION

MS BEHERA SANITARY AND HARDWARE

Bidder Name

RANA ENTERPRISES

M/s R.C REFRIGERATION

R.B.Construction

M/S T.N.CONSTRUCTION

MS BEHERA SANITARY AND HARDWARE

M/SNeelachal Enterprises

vaishnaveedevienterprises

MS SUBHAM ENGINEERING AND CO