REPAIR TO KITCHEN TILING, PLUMBING, JOINERY, MISC BR WORK AT JCOs, ORs MD ACCN IN ZONE D AREA AND PERIODICAL SERVICES, BR WORKS AT MES INSTALLATION UNDER AGE BR-II AT DINJAN MIL STN UNDER GE DINJAN

Amount

Demolition of brick work or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars etc but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and as directed.

Dismantling of plain or corrugated steel sheeting, any gauge, thickness, in roof covering including ridges complete all as specified and as directed.

Dismantling asbestos cement (corrugated or semi corrugated) sheet in roof covering complete all as specified and as directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings not exceeding 15 cm thickness. (below or above ground level) complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and disposing the rubbish off the premises complete all as specified and as directed.

Dismantling of frame work, timber scantlings 40 Sq.cm and over in section, in any position complete all as specified and as directed.

Dismantling of timber boarding, any description, fixed in any position with nails complete all as specified and as directed.

Dismantling of wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed.

M&L for plain cement concrete (1:4:8), type D2 (using 40 mm graded stone aggregate) as in foundation, filling and mass concrete complete all as specified and as directed.

M&L for Reinforced Cement Concrete 1:2:4, type B-1 (Using 20 mm graded stone aggregate) as in slab supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves etc complete all as specified and directed. (Note : reinforcement shall be measured and paid separately against respective item).

S&F TMT steel bars 10 mm dia., and over cut to length, bend to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality complete all as specified and directed.

Use and waste of form work to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200 mm thick (Horizontal or sloping) for flat rough finished surfaces of concrete complete all as specified and directed.

Use and waste of form work to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 5cm but n exc 10cm wide Rough finished surface of concrete, flat complete all as specified and as directed.

M&L for brick work with sub class 'B' bricks (old size brick), straight or curved on plan exceeding 6 m mean radius, built in cement mortar (1:6) complete all as specified and as directed.

M&L for brick work with sub class 'B' bricks, straight or curved on plan to any radius, built in cement mortar (1:4) as in half brick thick walls complete all as specified and as directed.

Taking down chowkats or frame with shutters (without taking off shutter from the frame) not exceeding 1.5 Sqm in each complete all as specified and as directed.

Taking down chowkats or frames with shutter (without taking off shutter from the frame) exceeding 1.5 Sqm but not exceeding 4 Sqm in each complete all as specified and as directed.

Taking down the shutters of any description not exceeding 1.00 Sqm each complete all as specified and as directed

Taking down the shutters of any description exceeding 1.00 Sqm and not exceeding 2.00 Sqm each complete all as specified and as directed

Taking down shutters of any description and refixing in same location/opening not exceeding 1 sqm each including resecuring or easing & adjusting also refixing existing serviceable builders hardware complete all as specified and as directed.

Taking down shutters of any description and refixing in same location/opening exceeding 1 sqm but not exceeding 2sqm each including resecuring or easing & adjusting also refixing existing serviceable builders hardware complete all as specified and as directed.

Resecuring or easing and adjusting without taking down the shutter of size exceeding 1 Sqm and not exceeding 2 Sqm complete all as specified and as directed.

M&L for second class hard wood timber scantling, clean swan as in frame work, fixed with nails complete all as specified and directed.

S&F for second class hard wood plain, solid, straight chowkat and frames, wrought, framed, rebated on the solid rounded or chamfered, put together with glue pinned at joints complete all as specified and as directed.

S&F pressed steel frames for doors of size 105x60mm with one or more rebates using cold rolled commercial mild steel sheet of 1.2mm thick including providing and fixing necessary lugs, 100mm butt hinges, lock strike plate, shock absorber etc and including PCC filling of hollow section using plain cement concrete (1:3:6) type C1 complete all as specified and as directed.

S&F pressed steel frames for doors of size 125x60mm with one or more rebates using cold rolled commercial mild steel sheet of 1.2mm thick including providing and fixing necessary lugs, 100mm butt hinges, lock strike plate, shock absorber etc and including PCC filling of hollow section using plain cement concrete (1:3:6) type C1 complete all as specified and as directed.

S&F for 35 mm thick, second class hard wood, glazed and skeleton shutters with open rebated and prepared to receive glass, gauze, etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut mitered beads for securing glass, etc, sizes of members of shutters as specified in SSR Part I, Section -8, clause 8.24 (a) complete all as specified and as directed..

S&F for 35 mm thick, second class hardwood, Plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats complete all as specified and as directed.

S&F 30 mm thick, second class hardwood glazed and skeleton shutters open rebated and prepared to receive glass, gauge, etc, divided in to squares, with plain, chamfered or rounded, mitered and rebated sash bars, any numbers, edges of framing plain, chamfered or rounded as in SSR Part I Section 8 clause 8.24 (b) complete all as specified and as directed..

S&F for solid PVC door frames of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube complete all as specified and as directed.

S&F for factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded, plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour 5mm thick PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement, complete all as specified and as directed.

S&F for 100mm size butt hinges, medium weight, cold rolled mild steel complete all as specified and as directed.

S&F for 75 mm size stainless steel, butt hinges, medium weight, cold rolled, complete all as specified and as directed.

S&F 150 mm long mild steel pressed handle, oval type, stove enameled black complete all as specified and as directed.

S&F for 150 mm size aluminium handles, cast type, anodised complete all as specified and as directed.

S&F for 100 mm size aluminium handles, cast type, anodised complete all as specified and as directed.

S&F 200mm long mild steel, barrel tower bolts, stove enamelled black, with bright bolt and fixed complete all as specified and as directed.

S&F 150mm long mild steel, barrel tower bolts, stove enamelled black, with bright bolt and fixed complete all as specified and as directed.

S&F for 150mm long aluminium, barrel tower bolts, stove enamelled black, with bright bolt and fixed complete all as specified and as directed.

S&F for 100mm long aluminium, barrel tower bolts, stove enamelled black, with bright bolt and fixed complete all as specified and as directed.

S&F for mild steel sliding door bolts, 250mm long, plate type, stove enamelled black, with bright bolts not less than 12mm dia with & including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate etc complete all as specified and as directed.

S&F for aluminium sliding door bolts, 250mm long, plate type, stove enamelled black, with bright bolts not less than 12mm dia with & including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate etc complete all as specified and as directed.

M&L for mild steel framed work such as grills, gratings, gates etc., with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bar, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work conforming to Fe-290 (Gde E-165) complete all as specified and directed.

S&F for mild steel small articles using flat iron of size 25x3mm thick such as band, strap, hold fast, cleat, support, hook, hinges, base tie for door frame etc and other similar items conforming to Fe-290 (Gde E-165) complete all as specified and as directed.

M&L for plain cement concrete (1:3:6) type C-1 (using 20 mm graded stone aggregate) for fixing hold fast complete all as specified and as directed.

S&F in repair steel windows with side double hung shutters including projecting /box type hinges with steel handle, and steel peg stay complete with glazing bars, devotailed or welded complete all as specified and as directed.

S&F in repair steel windows with side double hung shutters including projecting /box type hinges with steel handles and steel peg stay complete without glazing bars, dovetailed or welded complete all as specified and as directed.

S&F in repair steel ventilators with top hung shutter including two pairs of brass cup pivots, catch spring and pulley wheel complete all as specified and as directed.

S&F anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified complete all as specified and as directed.

S&F anodised aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified

S&F for galvanised mild steel wire cloth of 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with stainless steel wire staples complete all as specified and as directed.

S&F in repairs galvanised mild steel wire cloth of 0.36mm nominal dia of wire and average width of aperture 1.18mm and fixed with stainless steel wire staples complete all as specified and as directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or steel frames, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and as directed.

S&F for 3 mm thick sheet glass, ordinary quality and glazing with oil putty in square not exceeding 0.5 Sqm in each pane complete all as specified and as directed.

S&F for 4.8 mm thick sheet glass, ordinary quality and glazing with oil putty in square not exceeding 0.5 Sqm in each pane complete all as specified and as directed.

S&F for 12mm thick prelaminated particle board, interior grade, both side with decorative choice lamination fixed with screws to timber frame works as in shutter of cup board and other similar work complete all as specified and as directed.

S&F for pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of profile as approved, any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

S&F for pre-painted galvalume aluminium zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in ridges/valley gutter, fixed with self tapping screws complete all as specified and as directed. Note : Colour of ridge shall be same colour as that of sheet used for roof.

S&F for GI snap grid frame work of size 605mm x 605mm frame work for ceiling with aluminium tee section of size 23.5mm x 26.4mm x 1.4mm thick and aluminium angle section of size 36.5mm x 25mm x 1.4mm thick, for false ceiling including Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia, 40mm long including 4 mm thick non asbestos E-board (plain), HSPC fixed to frame complete including dismantling of existing ceiling any type complete all as specified and as directed.

M&L for preparation of new plastered surfaces and applying three coats of white wash of ceiling surface/ false ceiling etc complete all as specified and as directed.

S&F 6mm thick asbestos cement, two piece adjustable plain angular ridge fixed with L-type or J-type or cranked hook bolts complete all as specified and as directed.

S&F 6mm thick asbestos cement, corrugated sheet or semi-corrugated sheets fixed with L-type or J-type hook in roofs covering complete all as specified and as directed.

S&F 20 mm thick, second class hard wood boarding, clean sawn, planed one side with butt joints and fixed with nails in any situation as in eaves board, etc complete all as specified and directed.

S&F for false ceiling with exposed metal (PPGI) framework/ "Tee" grid providing and fixing of suspended Tee grid false ceiling using 'T" grid system - powder coated GI (PPGI) exposed grid false ceiling suspension system in grid size 600mmx600mm with main runner 32mm x 24mm x 0.3mm thick, cross tee 26mm x 24mm x 0.3mm thick and wall angle 24mm x 24mm x 0.40 mm thick using 4mm thick non asbestos fiber cement board of size 595mm x 595mm, and asbestos free fiber cement board manufacturer using high pressure system curing technology. T grid framing is suspended using 4mm GI/MS bar hanger fixed with steel dash fasteners or iron purlin from the roof with adjustment clip, also providing provisions for light fixtures, air conditioning diffusers and ducts, sprinklers, smoke detectors etc. The main runners to be secured to structural soffit by hanger @ 1220mm maximum c/c. The last hanger at the end of each main runner should not be placed at not more than 300mm from the adjacent wall. 1220mm/600mm cross tee to be interlocked between main runners @ 600mm c/c, so as to form 600mm x 600mm or 1200mm x 600mm grid, confirming IS 14862 and type B category III of ISO 8336, tested as per AS 1530 Part-3 & B. S-476 Part 4, 5, 6, 7 & 8 should be placed in grid module to form after and including dismantling of existing false ceiling of any type complete all as specified and as directed.

M&L for 75 mm thick, plain cement concrete (1:3:6) type C-1 (using 20mm graded stone aggregate) as in plinth protection, footpath, etc, finishing cement concrete surface even and smooth without using extra cement including making joints with bitumastic filing in proportion of bitumen and sand (1:2) making impressions of expanded metal whilst the concrete is green complete all as specified and as directed.

M&L for 75 mm thick plain cement concrete (1:4:8) type D-2 (using 40mm graded stone aggregate) as in sub base of floor, etc complete all as specified and as directed.

M&L for non-skid, ceramic, coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. including 15 mm thick screed bed in cement mortar (1:6) and set & jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles complete all as specified and as directed.

M&L for non-skid coloured ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, as in skirting etc. over 10 mm thick back coat of cement mortar in (1:4), set and jointed in neat cement slurry and pointed in white or colour cement to match over complete all as specified and as directed.

M&L for glazed, ceramic, coloured tiles of size 450mm x 300mm x 7-8mm thick, on vertical surfaces, set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles including 10 mm thick backing of cement mortar (1:4) complete all as specified and as directed.

M&L for prepolished chequered cement concrete tiles of size 20cm x 20cm x 25mm thick, as in floors etc, including 20 mm thick screed bed or bedding in cement mortar (1:4) and set and jointed in neat cement slurry and pointed in grey cement and pigments to match with the shade of tiles complete all as specified and as directed.

M&L for granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including 15 mm thick screed bed in cement mortar (1:4) complete all as specified and as directed.

M&L for machine pressed precast conctete interlocking paver block, design & shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade with grey cement and pigment including 75 mm thick compacted bed of coarse sand, filling the joints with fine sand etc. complete all as specified and as directed.

Taking down cement plaster on brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water complete all as specified and as directed

M&L for rendering 15 mm thick on fair faces of external wall of brick work or stone surfaces in two layers (10 mm and 5 mm thick) in cement mortar (1:4) using water proofing compound in top layer (water proofing compound measured as separately) and finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15 mm thick in cement mortar (1:6) on other than fair faces of brick masonry or concrete surfaces and finishing the surfaces even and smooth without using extra cement complete all as specified and as directed.

M&L for rendering 10 mm thick in cement mortar (1:4) on fair faces of brick masonry or concrete surfaces and finishing the surfaces even and smooth without using extra cement complete all as specified and as directed.

M&L for rendering 5 mm thick on ceiling in cement mortar (1:3) finished even & smooth without using extra cement complete all as specified and directed

Supply only water proofing compound complete all as specified and directed.

M&L for preparation of new plastered surface of walls etc and applying three coats of white wash on walls complete all as specified and directed

M&L for preparation of old plastered or unplastered surfaces of walls and applying one coat of white wash complete all as specified and as directed.

M&L for preparation of old old plastered or unplastered surfaces of ceiling and applying one coat of white wash complete all as specified and as directed.

M&L for preparing old plastered or unplastered surfaces of walls by washing, rubbing down and scraping of existing distempering/painted surfaces etc and applying one coat of distemper oil emulsion complete all as specified and as directed.

M&L for preparation old decorated plastered or unplastered surfaces of wall cornices etc by brooming down or steel wire brushing, scraping down, the surfaces covered by smoke soot, growth of moulds and moos, efflorescent, having oil and gresase spots and applying one coat of cement base paint (white or tinted) complete all as specified and as directed

M&L for preparation old decorated plastered or unplastered surfaces of wall cornices etc by brooming down or steel wire brushing, scraping down, the surfaces covered by smoke soot, growth of moulds and moos, efflorescent, having oil and gresase spots and applying one coat of cement base paint (white or tinted) including scaffolding upto 30 mtr height complete all as specified and as directed

M&L for preparation of new wood and wooden based surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed.

M&L for preparation of new steel surfaces of any description, over 10 cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of zinc chrome red oxide primer complete all as specified and as directed.

M&L for preparation of new plastered surface of walls etc and applying two coats of distempering interior walls with distemper oil emulsion white or tinted over chalk whiting complete all as specified and as directed.

M&L for preparation of new plaster surfaces of wall, and applying two coats of water based acrylic weather proof exterior emulsion (Apex ultima superior quality) paint over a coat of primer as per manufacturer's instruction complete all as specified and as directed.

Taking up or down 15 mm bore steel water tubing galvanised including connections from trenches/wall/floor/ ceiling etc and keeping serviceable quantity in safe custody for reuse at same site or other site complete all as specified and as directed.

Taking up or down 20 mm bore steel water tubing galvanised including connections from trenches/wall/floor/ ceiling etc and keeping serviceable quantity in safe custody for reuse at same site or other site complete all as specified and as directed.

Supply, laying, connection and testing, 15mm bore, steel water tubing, galvanised, medium grade conforming to IS 1239 (Part -1):2004 with all fittings conforming to IS 1239 (Part -2):2011 and fixtures fixed to walls and ceilings or laid in floors, etc complete all as specified and as directed.

Supply, laying, connection and testing, 20mm bore, steel water tubing, galvanised, medium grade conforming to IS 1239 (Part -1):2004 with all fittings conforming to IS 1239 (Part -2):2011 and fixtures fixed to walls and ceilings or laid in floors, etc complete all as specified and as directed.

Refixing 15mm bore old steel tubing and connections in new or old position (Walls, ceiling, floors, etc.) complete all as specified and as directed.

Refixing 20 mm bore old steel tubing and connections in new or old position (Walls, ceiling, floors, etc.) complete all as specified and as directed.

S&F in repair for 500 litres capacity rotational moulded polyethylene water storage tanks (cylindrical or vertical with closed top) as per IS 12701:1996, hoisted and fixed in position including provision of 20/15mm bore medium grade pipe for connecting inlet, outlet, overflow and washout pipe complete all as specified and as directed.

S&F in repair 1000 litres capacity rotational moulded polyethylene water storage tanks (cylindrical or vertical with closed top) as per IS 12701:1996, hoisted and fixed in position including provision of 20/15mm bore medium grade pipe for connecting inlet, outlet, overflow and washout pipe complete all as specified and as directed.

S&F 20 mm bore, ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed. (Minimum weight - 210 gms) complete all as specified and as directed.

S&F in repairs 20 mm bore, ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed. (Minimum weight - 210 gms) complete all as specified and as directed.

M&L for water proofing treatment on RCC roof etc. comprising with the following operation and as specified herein below and as directed:- (a) Taking down existing old tarfelt, bituminous compound including cleaning & removing debris to a distance exc 100m & n.exc.250m. (b) 15 mm thick plastering in cement mortar 1:4 finished even & smooth. (c) Preparing & cleaning of fully dried cement plastered surface. (d) Applying one coat of cold bituminous primer to the plastered surface @ 0.25 liters per sqm conforming IS-3384 (e) A layer of APP based polymeric membrane membrane 3mm thick (minimum) weighing 3.5 kg per sqm reinforced with polyster non woven fabric (weighing not less than 160 gms/sqm )shall be applied over bituminous primer as specified above. Application of polymeric membrane shall be by torch application. The over lap shall be minimum 100 mm on transverse direction and 75 mm in longitudinal direction. (f) One coat of aluminium paint over the APP based membrane @ 0.11 Kg/Sqm Note :- Prior to execution of the APP Membrane works, leak proof test shall be done by ponding water on roof slab to minimum depth of 25 mm. The entire roof slab shall be flooded with water for 48 hours. The necessary barrier shall be made to make feasible to stagnate water for 48 hours on roof slab.

S&F in repairs 15 mm bore, bib taps, cast copper alloy, chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and as directed.

S&F in repairs 15 mm bore dia, stop valves, cast copper alloy, fancy type, chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed.

S&F 15 mm bore, pillar taps, fancy type, cast copper alloy, chromium plated with capstan heads, screwed down high pressure with or without lettered 'Hot or Cold' with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and as directed.

S&F in repairs swivel shower of PTMT any colour for fixing with 15mm pipe. (Minimum weight 40gms) including shower arm 15 mm size, 195mm long with bend of 45 degree with flange of PTMT any colour (Minimum weight 40gms complete all as specified and as directed.

S&F in repairs 15 mm bore, bib taps, PTMT, any colour, high pressure screwed for iron pipes and fixed (minimum weight 15mm-90gms/20mm-125gms) complete all as specified and as directed.

S&F in repairs 15 mm bore, Stop valve, PTMT, any colour, high pressure screwed for iron pipes and fixed (minimum weight 15mm-90gms/20mm-125gms) complete all as specified and as directed.

S&F in repairs 15mm bore, PVC connection pipe 600mm long with PTMT nuts at both ends complete all as specified and as directed.

S&F in repair CP health faucet cast copper alloy with push button & 1m long flexible steel pipe with PVC lining suitable for 15mm bore pipe complete all as specified and directed.

S&F in repairs 10 liter capacity, PVC valve less syphonic duel type, flushing cistern, low level, white, with inlet, ball valve, flush pipe, float and handle including brackets complete all as specified and as directed.

S&F for grating doom, circular type, 100mm dia of PTMT, (mimimum weigh 25 gms) complete all as specified and as directed.

S&F in repairs vitreous china squatting pan, 'Orissa' pattern, size 580 x 440 mm white with integral foot rest and 'P' or 'S' trap, including provision of lime concrete bedding, connection to trap and flushing pipe (32mm dia) etc complete including making good to disturbed surfaces of floor using concrete (1:2:4) type B0 and to match with existing specifications complete all as specified and as directed.

S&F in repairs vitreous china wash down water closet pan (pedestal pattern), white, including connection to outgoing drain and flushing pipe, anti syphonic pipe with PVC seat and cover complete but excluding flushing cistern & flush pipe including making good to disturbed surfaces of floor using concrete (1:4:8) type D2 and to match with existing specifications complete all as specified and as directed.

S&F in repairs vitreous china wash basin, size 550x400mm, white, flat back, including PVC waste pipe, CP waste coupling, chain, plug and porcelain stopper & brackets including cutting for and pinning in ends of brackets but excluding tap complete all as specified and as directed.

S&F in repairs stainless steel kitchen, sinks made of 1 mm thick sheet for kitchen or laboratory with plugs, washers and wastes including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm and bowl size 410mmx330mmx160mm complete all as specified and directed.

S&F in repairs 32/40 mm dia x 800mm long waste pipe for sink/wash basin/ urinal etc complete all as specified and directed.

S&F in repairs 32/40 mm dia waste coupling of PTMT (half or full thread) for sink/wash basin/ urinal etc complete all as specified and directed.

Forming 12mm thick Expansion joints filled with pre-formed bituminous filler and top 30mm primed and sealed with sealing compound, Grade ‘A’ for 50-75 mm thickness of concrete slab complete all as specified and as directed.

S&F in repair 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and as directed.

S&F in repairs curtain rails, Harrison rail, aluminium alloy with fixing brackets, stops, rollers etc complete all as specified and as directed.

S&F in repairs110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed.

S&F in repairs 75 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed.

S&F for 110 mm bore, PVC (SWR) bends of any radius complete all as specified and as directed.

S&F in repairs 75 mm bore, PVC (SWR) floor trap, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and as directed.

M/s GANDHESWAR PHUKAN

M/S AUTOMOTIVE WORLD

R.D.CONSTRUCTION

MAZUMDAR ENTERPRISE

Construction House

R D Enterprises

NChetia and Sons Trading