Construction of temporary office building at Gulab Bagh, INA, New Delhi for General Consultant of Delhi - Gurugram- Bawal Namo Bharat Corridor.

The Price bid shall be read in conjunction with the Bidding Documents.

There are 3 Schedules in the Financial Bid as follows : (i) Schedule-A : (Civil) (ii) Schedule-B : (PEB) (iii) Schedule-C: (Electrical, HVAC, Telecom & IT) The bidder is required to quote a flat percentage "Above" (+) / "Below" (-) / "At par" on the Total amount of all the Schedules in the "BoQ1" Sheet and further discount, if any, may be Quoted in the "Letter of Price Bid" along with methodology of discount. The percentage quoted by the Bidder in "BoQ1" sheet and discount (if any) quoted by the Bidder in the "Letter of Price Bid" will be applied on the individual rate mentioned under Column "6"(rate without GST) of each schedule, for the purpose of payment to the Contractor.

The quantities for various items provided in the Price Bid are estimated quantities and are given to provide a common basis for Bidding. During the execution of works, the same may vary based upon "Good for Construction" (GFC) drawings approved by the Engineer and as per the site conditions. The basis of the payment will be the actual quantities of the work executed and accepted by the Engineer or quantities as per the GFC drawings whichever is less and shall be paid /valued as per the accepted rates.

The quoted rates for various items are for completed and finished items of work complete in all respects. It will be deemed to include all the cost involved in the execution of the items and shall include all duties, taxes [except Goods and Service Tax (GST) and Custom Duty] royalties, cess, overheads, profit and other levies payable by the Bidder under the Contract, or for any other cause etc. The Bidder shall be required to consider this aspect while quoting rates. It shall include all general risks, liabilities and obligations set out or implied in the Contract shall and including remedy of any defects during the Defect Liability Period, unless otherwise provided in the Contract. The whole cost of complying with the provisions of the Contract shall be deemed to have been included in the quoted rates. GST as prevalent will be paid extra.

Bidder may please note that to perform this contract. nothing extra shall be payable on account of field constraints, non-availability of uninterrupted front, cost of project management, monitoring, coordination and supervision, cost of adhering to quality requirements (QA/QC), cost of adhering to SHE requirements, cost of preparing drawings and documents, as-built records and documentation, preparation of detailed scheme for taking necessary clearance and approval from the concerned authority and other local bodies etc.

Income Tax and any other statutory taxes to be deducted at source will be deducted by the Employer from the due payments of the contractor in accordance with the prevailing rules in force.

Bidder should not tamper the Price Bid. If the Price Bid is found to be modified by the bidder, then the same will be treated as incomplete and non-responsive and shall result in the rejection of the Bid.

Method of Quoting the Price in the Price Bid The Price Bid is in Excel Format and the Quoting the Price in the Price Bid should be as Follows: (i) Whole Excel Worksheet is Locked except the Cells which are highlighted in Blue. (ii) Bidders are required to fill these cells which are highlighted in Blue only. (iii) Bidder is required to quote a flat percentage Excess/Less/At par on 'Total Amount of all the Schedules' in "BOQ1'' Sheet of Price Bid and further discount if any in "Letter of Price Bid" along with methodolodgy of discount if any. (iv) All 'blanks' in the Pricing Document, where the Bidder is permitted to quote shall be filled in. (v) If some % is quoted inspite of marking 'At par' that % will not be considered and it will be taken as "At par" on basic amount. Failure to quote the % in case of excess or less for the "Total amount of Schedule shall be treated as "At Par" and shall be evaluated accordingly. (vi) Bidder is required to quote Rates in INR only.

Errors will be corrected by the Employer for any arithmetic errors in computation or summation as per contract conditions.

Item Rate BoQ

BoQ_Ver4.0

Name of the Bidder/ Bidding Firm / Company :

PRICE SCHEDULE (This BOQ template must not be modified/replaced by the bidder and the same should be uploaded after filling the relevent columns, else the bidder is liable to be rejected for this tender. Bidders are allowed to enter the Bidder Name and Values only)

NUMBER #

SCHEDULE-A

SCHEDULE-B

SCHEDULE-C

Total Amount of Schedules.(Excluding GST)

Letter of Price Bid

Bid No.:

National Capital Region Transport Corportation Limited

GatiShakti Bhawan,INA, New Delhi- 110023

We, the undersigned, declare that:

[amount in INR in figures]

DISCOUNT (IN %age )

Amount

Name of the authorized representative of the bidder

Desiganation of the authorized representative

Name of the Bidder/ Bidding Firm / Company :

Date: (DD/MM/YYYY)

Bid No. DA/MS/CPM-DS/040

Schedule-A (Civil items)

Schedule A:

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge- All kinds of soil

filling available excavated earth in treanch plinth,sides,of foundation etc. in layer not exceeding 20 cm in depth,consolidating each deposited layer by raming and watering.lead up to 50 mm lift upto 1.50 m.

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete.

Centering and shuttering including strutting, propping etc. and removal of form work for:- foundation ,footing,bases for column.

Providing and laying in position ready mixed plain cement concrete, with cement content as per approved design mix and manufactured in fully automatic batching plant and transported to site of work in transit mixer for all leads, having continuous agitated mixer, manufactured as per mix design of specified grade for plain cement concrete work, including pumping of R.M.C. from transit mixer to site of laying and curing, excluding the cost of centering, shuttering and finishing, including cost of curing, admixtures in recommended proportions as per IS : 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineerin-charge (All works upto plinth level) :-M-15 grade plain cement concrete (cement content considered @ 240 kg/cum)

FORM WORK Centering and shuttering including strutting, propping etc. and removal of form for Centering and shuttering including strutting, propping etc. and removal of form for :- Lintels, beams, plinth beams, girders, bressumers andcantilevers

FORM WORK Centering and shuttering including strutting, propping etc. and removal of form for:- All Heights Column , Pillars , Piers , Abutments,Posts and struts

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level:- Thermo-Mechanically Treated bars of grade Fe-500D or more.

Brick Work With Common Burnt Clay F.P.S(non modular) bricks of class designation 7.5 in Foundation & plinth in Cement Mortar 1:6 (1Cement:6 Course Sand)

Providing and laying Autoclaved Aerated concrete(AAC) blocks masonry with 150 mm to 300 mm thick with Grade-1 AAC blocks of density 551 to 650 kg/cum conforming to IS:2185 (Part 3) in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete s per direction of Engineer-in-Charge. (The payment of RCC band and reinforcement shall be made for seperately).

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Granite work

Designing, fabricating, testing, installing and fixing in position Curtain Wall with Aluminium Composite Panel Cladding, with open grooves for linear as well as curvilinear portions of the building , for all heights and all levels etc. including: (a) Structural analysis & design and preparation of shop drawings for pressure equalisation or rain screen principle as required, proper drainage of water to make it watertight including checking of all the structural and functional design. (b) Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding in pan shape in metalic colour of approved shades made out of 4mm thick aluminium composite panel material consisting of 3mm thick FR grade mineral core sandwiched between two Aluminium sheets (each 0.5mm thick). The aluminium composite panel cladding sheet shall be coil coated, with Kynar 500 based PVDF / Lumiflon based fluoropolymer resin coating of approved colour andshade on face # 1 and polymer (Service) coating on face # 2 as specifiedusing stainless steel screws, nuts, bolts, washers, cleats, weathersilicone sealant, backer rods etc.(c) The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot DipGalvanised with serrations and serrated washers to arrest the wind loadmovement, fasteners, SS 316 Pins and anchor bolts of approved makein SS 316, Nylon separators to prevent bi-metallic contacts all completerequired to perform as per specification and drawing The item includescost of all material & labour component, the cost of all mock ups atsite, cost of all samples of the individual components for testing in anapproved laboratory, field tests on the assembled working curtain wallwith aluminium composite panel cladding, cleaning and protection ofthe curtain wall with aluminium composite panel cladding till the handingover of the building for occupation. Base frame work for ACP cladding ispayable under the relevant aluminium item.s The Contractor shall providecurtain wall with aluminium composite panel cladding, having all theperformance characteristics all complete , as per the Architecturaldrawings, as per item description, as specified, as per the approvedshop drawings and as directed by the Engineer-in-Charge. However, forthe purpose of payment, only the actual area on the external face of thecurtain wall with Aluminum Composite Panel Cladding (including widthof groove) shall be measured in sqm. up to two decimal places.

Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete.

Providing and fixing panelled or panelled and glazed shutters for doors ,windows and clerestory window fixing with butt hinges of required size with necessary screw, excluding panelling which will be paid for separately ,all complete as per direrction of engineer-in-charges.(note; butt hinges and necessary screws shall be paid separately) Second class teak wood 35 mm thick shutters:

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete.

Providing and fixing partition upto ceiling height consisting of G.I. frame and required board, including providing and fixing of frame work made of special section power pressed/ roll form G.I. sheet with zinc coating of 120 gms/ sqm(both side inclusive), consisting of floor and ceiling channel 50mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener or metal screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre, and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and ceiling channels at the spacing of 300 mm centre to centre. The boards are to be fixed to the frame work with joints staggered to avoid through cracks, Galvanised M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm each with zinc coating of 120 gms/sqm(both side inclusive)) to be provided at the horizontal joints of twoboards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush finish with recommended jointing compound, jointing tape, angle beads at corners (25 mm x 25 mm x 0.5 mm), joint finisher and two coats of primer suitable for board as per manufacture's specification and direction of engineer in charge all complete. 75 mm overall thickness partition with 12.5 mm thick double skin fire rated Glass Reinforced Gypsum (GRG) plaster board conforming to IS: 2095: (part 3) : 1996 (Board with BIS certification marks)

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Providing and fixing pressed steel door frames conforming to IS:4531,manufactered from commercial mild steel sheet of 1.60mm thickness,including hinges,jamb,lock jamb,bead and if required angle threshold of mild steel angle of section 50 x 25 mm or base ties of 1.60 mm,pressed mild steel welded or rigidly fixed together by mechanical means,including m.s pressed butt hinges 2.5mm thick with mortar guards,lock strike-plate and shock absorbers are specified and pplying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer in charge Profile C Fixing with adjustable lugs with split end tail to each jam

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Providing and laying Vitrified tiles in different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS: 15622, of approved brand & manufacturer, in all colours and shade, in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately). Size of Tile 600x600 mm

Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineer-in-charge.size of tile 600X600 mm

Providing and fixing removable raised/false access flooring with system and its components of approved make for different plenum height with possible height adjustment upto 50 mm, comprising of modular load bearing floor panels supported on G.I. rectangular stinger frame work and G.I. Pedestal etc. all complete, as per the architectural drawings, as specified and as directed by Engineer-in-charge consisting of:300 mm Finished Floor Height (FFH)

Providing and fixing false ceiling at all heights including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediatechannel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25 mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer’s specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks)

CEMENT PLASTER (IN COARSE SAND) 12 mm cement plaster of mix 1:6(1cement:6coarse sand)

15 mm cement plaster on rough side of single or half brick wall of mix: 1:6 (1 cement: 6coarse sand)

18 mm cement plaster in two coats under layer 12 mm thick cement plaster 1:5 (1 cement : 5 coarse sand) and a top layer 6 mm thick cement plaster 1:3 (1 cement : 3 coarse sand) finished rough with sponge.

CEMENT PLASTER IN TWO COATS :- 20 mm cement plaster 1:2 (1 cement : 2 stone dust).

Providing and Applying Plaster of Paris Putty of 2mm thickness Over Plastered Surface to Prepare the Surface even and Smooth Complete

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade:- Two or more coats on new work

French spirit polishing : Two or more coats on new works including a coat of wood filler

Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour: Two Coates

Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content. With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre

Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge).

Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required : Single half stall urinal with 5 litre P.V.C. automatic flushing cistern

Providing & Fixing White Vitereous China Extended Wall Mounting Water Closet Of Size 780X370X690 mm Of Approved Shape including P&F White Vitreous China Cistern With Dual Flush Fitting

Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms.15 mm nominal bor

18.2 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, havingthermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing.This includes jointing of pipes & fittings with one step CPVC solventcement and the cost of cutting chases and making good the sameincluding testing of joints complete as per direction of Engineer in Charge.Concealed work, including cutting chases and making good the wallsetc:- 20mm nominal outer dia pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, havingthermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing.This includes jointing of pipes & fittings with one step CPVC solventcement and the cost of cutting chases and making good the sameincluding testing of joints complete as per direction of Engineer in Charge.Concealed work, including cutting chases and making good the wallsetc:- 25mm nominal outer dia pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge:- 32 mm nominal outer dia pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge:- 40 mm nominal outer dia pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge:- 50 mm nominal inner dia Pipes

Providing and fixing uplasticised PVC connection pipe with brassunions : 15 mm nominal bore

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15 mm nominal bor

Providing and laying non-pressure NP2 class (light duty) R.C.C pipes with collers jointed with stiff mixture of cement mortar in the proportion of 1: 2( 1 cement : 2 sand )including testing of joints etc . Complete :- 250 mm dia RCC pipe

Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double action hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-incharge (Door handle, lock and stopper etc.to be paid separately).

Providing and fixing double scaffolding system (cup lock type) on the exterior side of building/structure, upto 25 metre height, above ground level, including additional rows of scaffolding in stepped manner as per requirement of site, made with 40mm dia M.S. tube, placed 1.5 metre centre to centre, horizontal & vertical tubes joint with cup & lock system with M.S. Tubes, M.S. tube challis, M.S. clamps and staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for execution of work of cleaning and/ or pointing and/ or applying chemical and removing it thereafter. The scaffolding system shall be stiffened with bracings, runners, connecting with the building etc, wherever required, if feasible, for inspection of work at required locations with essential safety features for the workmen etc., complete as per directions and approval of Engineer-in-charge. Note:- (1) The elevational area of the scaffolding shall be measured for payment purpose. (2) The payment will be made once only for execution of all items for such works.

Providing and fixing mineral fibre false ceiling tiles at all heights of size 595X595 mm of approved texture, design and pattern. The tiles should have Humidity Resistance (RH) of 99%, Light Reflectance ≥ 85%, Thermal Conductivity k = 0.052 - 0.057 w/m K, Fire Performance as per (BS 476 pt - 6 &7)in true horizontal level suspended on interlocking T-Grid of hot dipped all round galvanized iron section of 0.33 mm thick (galvanized @120 gsm) comprising of main T runners of 15x32 mm of length 3000 mm, cross T of size 15x32 mm of length 1200 mm and secondary intermediate cross T of size 15x32 mm of length 600 mm to form grid module of size 600x600 mm suspended from ceiling using galvanized mild steel item (galvanised@80gsm) 50 mm long 8 mm outer diameter M-6 dash fasteners, 6 mm diameter fully threaded hanger rod up to 1000 mm length and L-shape level adjuster of size 85x25x2 mm, spaced at 1200 mm centre to centre along main ‘T’. The system should rest on periphery walls /partitions with the help of GI perimeter wall angle of size24x24X3000 mm made of 0.40 mm thick sheet, to be fixed to the wall with help of plastic rawl plug at 450 mm centre to centre & 40 mm long dry wall S.S. screws. The exposed bottom portion of all T-sections used in false ceiling support system shall be pre-painted with polyester baked paint, for all heights. The work shall be carried out as per specifications, drawings and as per directions of the engineer-in-charge :-With 16 mm thick Beveled mineral Fiber False Ceiling Tile (0.55 to 0.6)

Providing & Grouting of dowel tubes / shear keys / joints of precast members with m60 grade cementitious grout(non shrink) of approved make by suitable means( Free flowing/pump), curing etc. Complete as per direction of Engineer-incharge.(The payment shall be made on the basis of actual weight of approved grout injected.):-Stirrer mixed cementitious grout(non-shrink) of approved make in dowel tubes / shear keys /joint of precast members

Casement Door & Windows (UPVC)

Casement Door & Windows without opening (UPVC)

Providing and fixing C.P. Brass extension nipple (size 15 mm x 50 mm) of approved make and quality as per direction of Engineer-in-charge.

Providing and fixing pillar cock ( make- Jaquar) Code PRS-031, complete as per direction of Engineer-in-charge.

Providing & fixing 12 mm thick toughned glass Urinal Partitions With Frosted Film and as per approved design and direction of engg-in charge

Providing & fixing White Vitereous Oval/Circular(Table Top) Washbasin

Providing & fixing Dorset or its equivallent handle 334mm for approved quality with necessary screws etc. all complete Eden ED06 PSS

Providing & fixing Stainless Steel Jali of Approved Quality &Colour,Circular Type 100mm nominal dia

Providing & fixing Health faucet in WC of washrooms of approved quality,complete as per the direction of engg. In charge

Providing & fixing Door buffer-Wall Mounted dia-22mm Ht. 75mm Without Cover(Stainless Steel)Acuacted of Approved quality with neccesary screws etc. All Complete Model No. DB(22)

100 mm thick C.C. paver block of M-35 grade with approved colour design and pattern.

Stair case granite fixing for treads and riser

Providing and fixing of Sintex under ground water tank ( 10000 ltr) with installation as per direction of engineer in charge

Providing and applying hertiage smooth stone finish texture ( external work) as per direction of Engineer in incharge.

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 110 mm diameter

Providing and fixing 5mm toughened glass in wooden door frames complete in all respects as per site requirements and directions of engineer in charge

Providing and installation of 2HP submersible pump with starter including all necessary fittings for operation in UG tank complete in all respect as per directions of engineer in charge

Providing and installation of 1HP centrifugal pump with starter including all necessary fittings for operation, complete in all each respect as per directions of engineer in charge.

Providing and applying of fiber reinforced polymer waterproofing using xylene primer with two component resin and hardener with 2 layers of fiber glass mesh of 450 CSM complete in all respect as per directions of engineer in charge.

Any other DSR 2023 (Excl. GST)

Total Amount of Schedule A (Excl. GST)

Bid No. DA/MS/CPM-DS/040

Schedule B : (PEB Items)

Total of Schedule B: (PEB Items) (Excl. GST)

Total of both the Buildiings

Escalated Rate Calculation

Steel Structure

Deck Sheet

26.92% escalated Presentage

GC Building

Deck Sheet Calculations considering 85.53m x 15m (1st Floor) & 87.53m x 17m (2nd floor) Area

Building at Land A

Total:

GC Building at Plot 'B'

Building at Land B

Total:

Bid No. DA/MS/CPM-DS/040

Schedule-C(Electrical, HVAC,Telecom & IT items)

Supplying and fixing of following sizes of steel conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required.

DISTRIBUTION BOARD

INTELLIGENT FIRE ALARM SYSTEM

EARTHING AND EARTH CONDUCTOR

External Lighting

LIGHT FIXTURE AND FANS

FIRE ALARM SYSTEM

CABLES

Brass compression gland and aluminium lugs

TELECOME AND IT WORK (D)

Supply of following sizewall mounted MDF Complete with sa plusdisconnection module , back mounting frame & wire manager on good quality power coated base plate : 200pair MDF

Supplying and fixing of following sizes of PVC conduit 25mm along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required.

Supply of 4 pair CAT-6 UTP LAN / data cable, fire retardant LSZH

Laying fixing & termination of 4 pair CAT-6 UTP LAN/ Data cable in the existing surface /recessed steel/ PVC conduit as required.

supplying of 24 port modular CAT-6 jack panel with wire manager etc.

Make: DAIKIN/ MITSUBISHI ELECTRIC/ O GENERAL

ODU GROUND FLOOR AIR CONDITIONING (20 HP X 4. Nos)

ODU TREATED FRESH AIR UNIT (10 HP x 2Nos.)

Supply, Installation, testing & commissioning of wall Mounted High static type Unit of following capacity suitable to operate from 230+10% volt, 50 HZ, 1 phase power supply cordless remote control, fittings & required cable to connect indoor unit to socket.Refrigerant Pipe size and gas quantity should suit to the copper pipe length at actual.The capacity guarantee should be ensured by the vendor. All indoor Units must have force shut adaptor to connect with fire alarm, so that the unit automatically stops in case of fire.

Make: DAIKIN/ MITSUBISHI ELECTRIC/ O GENERAL

Wall Mounted Type Indoor Unit - 1.65 TR

Wall Mounted Type Indoor Unit - 2.08 TR

Cordless Remote Controls for Above Units

DX AHU UNITS (TFA)

Make: ZECO/EDGETECH/CRYSTAL ( VRV COMPATIBLE)

Supply of Treated Fresh Air Unit as per specs below. Unit type: Ceiling Suspened, TFA, DX Coil. Outer skin: 0.8 mm Pre- coated GI, Inner Skin: 0.8 mm Plain G.I Frame work: Thermal break Al profile with thermal barrier. Thickness of insulated panels: 43 mm thick, CFC Free PUF injected (Density: 40 kg / Cu. m.) Material of Drain pan: 18 G SS-304 Tray duly insulated with 13 mm closed cell Nitrile insulation. Unit Base: G.S.S Base Channel The face velocity across filter & coil has been considered 500 FPM. Fan outlet velocity up to 10 M/S. Motors should VFD compatible however VFDs are not in our scope of supply. Coil section with 8 row deep DX type cooling coil with single no. of distributor. Coil Casing / Blank off: GI , Material Of Tube: Copper Fan section with imported DIDW forward curved centrifugal fan, Drive set with V belt & Motor (IE-2).The unit shall have limit siwtch. Rates are including Installation, testing & commissiong of this item.

Expansion Valve and Contorl Kit (10 HP)

Electrical Integration Kit

Remote Control (Standard Model)

REFNET-joints

Make: DAIKIN/ MITSUBISHI ELECTRIC/ O GENERAL

Refrigerant Piping

Make: Copper Pipes - MEXFLOW/MANDEV/RAJCO, Insulation Class O : ARMACEL/KLFEX

Drain Piping

Make: Pipes - SUPREME/PRINCE, Insulation Class O : ARMACEL/KLFEX

VENTILATION

Make: Systemair/Caryaire/ Ostberg

AIR DISTRIBUTION

MAKE FABRICATOR: ZECO/DUCTOFAB/ROLASTAR GSS SHEET: JINDAL/SAIL 24 Gauge ( Thickness 0.63mm)

Supply, installation, balancing and commissioning of fabricated at site GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required:- 24 Gauge ( Thickness 0.63mm)

MAKE FOR AIR DISTRICUTION PRODUCTS: DYNAMIC/AIRFLOW/CARYAIRE

Supply, installation, testing and commissioning of GI volume control duct damper complete with neoprene rubber gaskets, nuts, bolts, screws linkages, flanges etc, as per specifications.

Supplying & fixing of powder coated extruded aluminium Return Air Grills with louvers but without volume control dampers complete as required.

Supply, Installation, testing & commissioning of Constant Airflow Regulator. CAR shall have regulation mechanism with a stainless steel spring and a silicone membrane.CAR shall have a tool-free airflow setting mechanism. CAR shall be classified UL 2043, CAR shall have a temperature range for use from -10° to 60°C. Dia:100 mm/ 50 CFM

Supply, Installation, testing & commissioning of pre insulated flexible duct duly insulated with 25 mm thick glass wool of 24 Kg/Cum density of following sizes duly supported at regular interval as per site requirement etc. complete as required as per specifications. 100 mm dia.

Supply, Installation, testing & commissioning of single piece GI round spigot made out of spinning process with 50mm height and having grooves on both sides and circular flanges. Spigots shall be installed on main ducts to facilitate connection of flexible ducts:- 100 mm Dia.

INSULATION

MAKE: ARMACELL/K-FEX/A-FLEX

ELECTRICAL-CABLES & CABLE TRAY

MAKE: KEI/FINOLEX/POLYCAB/BATRA HENLEY

MAKE: SVS/GSP/RICO

MAKE: KEI/FINOLEX/POLYCAB/BATRA HENLEY

LT PANEL

Total (Schedule C) (Excl. GST)