Item 1 External Electrification decorative Lightning HV AC and Fire fighting work for Development of Foutain Squaire at VT road Mansarover RHB Jaipur

Amount

The pole shall be tubular in shape, made with different distinct sections which shall be welded using special V groove technique with MIG welding process. The decorative base and the decorative flower on midsection of the pole will be made of GDC aluminium conforming to LM6 specification. Decorative Ornamental Base GDC housing at the pole bottom, decorative design / ring embellishments made of GDC aluminium at the mid portions with a cross arm at the top. They should be properly integrated with the pole The pole shall consist of two sections, made of MS circular tubes of ∅139.7mm x 3.6mm thick of 1000mm length at the bottom, ∅76.1mm x 2.6mm thick of 3259mm length at the second section, with steel of grade YSt 210 to IS 3601 : 2006 and shall be able to withstand the wind speed of 50 m/sec, considered in design as per IS 875 (Part 3) : 1987. The pole shall be provided with built-in control box with PDC aluminium service door and a safety chain. The control gear tray is to be prewired with Ramanuj 4way connector for loop-in loop-out arrangement and Siemens / Crabtree make MCB & connector. The gear tray wiring shall be with 2.5 sqmm copper cable. The wiring will be limited to gear tray only The Pole is to be provided with a surface mounting base plate of size 200 x 200 x 12 mm, (steel of grade E250 to IS 2062 : 2011). The mounting plate shall be provided with elongated holes (38 x 19) for alignment of the pole to suit M16 Bolt at CC 140. The Pole is to be coated with an epoxy zinc rich penetrating primer 45 microns thick and finished with polyurethane base paint for a long lasting finish with 45 microns coat in required colour. Wherever special finish of antique gold, copper or any metallic colours is done, an additional coat of lacquer is to be provided.. • Hot dip GI foundation bolts and nuts (Grade 4.6 to IS 1367) are to be supplied with the poles. • Foundation template is to be provided

Foundation Bolt, 4 Nos of M16 x 500 mm bolt with 2 Nuts & 2 Washer

50W WW CRI >70 or suitable, post top luminaire with total system lumen of not less than 6220lm. The luminaire housing made of die cast aluminium with dimension A9: 634mm(dia) x 1065mm height. The PCB / LED module along with driver is housed inside and covered with acrylic diffuser / white powder coated aluminium sheet and supporting brackets. Prewired with LED driver and suitable for operation on 240V, 50Hz, single phase ac supply. Luminaire should be suitable for mounting on 60mm OD pipe with cable entries for through-wiring of mains supply cable with Integral power supply and earth connection. The protection class should be IP 65. LM 79 Report to be submitted

Decorative Single arm, surface mounting type lighting pole of total height 6.00 meters above ground. The luminaire bracket is a decorative single arm type with an arched design, two flower made of GDC aluminium, a overhang of 1000mm and mounted on to a vertical 60.3 dia pipe as a single piece assembly, which can be fitted on to a pole top and oriented in any direction. The decorative double arm bracket holding pipe will be fitted on top with a 620mm of height cast aluminium ornamental finial. The pole shall be tubular in shape, made with different distinct sections which shall be welded using special V groove technique with MIG welding process. The decorative base and the decorative flower on mid section of the pole will be made of GDC aluminium conforming to LM6 specification. The Pole design has some special provisions with a gravity die cast aluminium Finial on pole top with a minimum height of 620 mm, Decorative Ornamental Base GDC housing at the pole bottom, decorative floral design / circular ring embellishments made of GDC aluminium at the mid portions, for architectural appeal. They should be properly integrated with the pole The pole shall consist of two sections, made of circular tubes of Ø139.7 mm x 3.6mm thick of 1200mm length at the bottom section, Ø114.3 mm x 3.2mm thick of 3161mm length at the second section with steel of grade YSt 210 to IS 3601 : 2006 and shall be able to withstand the wind speed of 50 m/sec ,considered in design as per IS 875 (Part 3) : 1987. The decorative arched design single arm bracket made of circular tube of Ø38.1 and overhang length of 1000 mm shall be mounted on to a Ø60.3mm circular tube in single piece formation. This single piece assembly should be capable of orientation in any direction and secured with stainless steel 304 grade allen grub screws. The bracket is to be prewired with 1.0 sqmm copper cable and with connector. The pole shall be provided with built-in control box with PDC aluminium service door and a safety chain. The control gear tray is to be prewired with Ramanuj 4way connector for loop-in loop-out arrangement and Siemens / Anchor make MCB & connector. The gear tray wiring shall be with 2.5 sqmm copper cable. The wiring will be limited to gear tray only The Pole is to be provided with a surface mounting base plate of size Ø280 x 12 mm, (steel of grade E250 to IS 2062 : 2011) and welded at the bottom of the pole with supporting gussets. The mounting plate shall be provided with elongated holes (38 x 19) for alignment of the pole to suit M16 Bolt at PCD 230. The Pole is to be coated with an epoxy zinc rich penetrating primer 45 microns thick and finished with polyurethane base paint for a long lasting finish with 45 microns coat in required colour. Wherever special finish of antique gold, copper or any metallic colours is done, an additional coat of lacquer is to be provided. Accessories : • Hot dip GI foundation bolts and nuts (Grade 4.6) are to be supplied with the poles. • Foundation template is to be provided.

Foundation Bolt, 4 Nos of M16 x 500 mm bolt with 2 Nuts & 2 Washer

50W, post top luminaire . The Luminaire made up of spun alumininum body with dimension A9: 634mm(dia) x 618mm height. The PCB / LED module along with driver is housed inside and covered with acrylic diffuser / white powder coated aluminium sheet and supporting brackets. Prewired with LED driver and suitable for operation on 240V, 50Hz, single phase ac supply. Luminaire should be Suitable for mounting to internally threaded pipe of designation M30 with cable entries for through-wiring of mains supply cable with Integral power supply and earth connection. The protection class should be IP 65. LM 79 Report to be submitted

The pole shall be tubular in shape, made with different distinct sections which shall be welded using special V groove technique with MIG welding process. The decorative base and the decorative flower on midsection of the pole will be made of GDC aluminium conforming to LM6 specification. Decorative Ornamental Base GDC housing at the pole bottom, decorative design / ring embellishments made of GDC aluminium at the mid portions with a cross arm at the top. They should be properly integrated with the pole The pole shall consist of two sections, made of MS circular tubes of ∅139.7mm x 3.6mm thick of 1000mm length at the bottom, ∅76.1mm x 2.6mm thick of 2660mm length at the second section, with steel of grade YSt 210 to IS 3601 : 2006 and shall be able to withstand the wind speed of 50 m/sec, considered in design as per IS 875 (Part 3) : 1987. The pole shall be provided with built-in control box with PDC aluminium service door and a safety chain. The control gear tray is to be prewired with Ramanuj 4way connector for loop-in loop-out arrangement and Siemens / Crabtree make MCB & connector. The gear tray wiring shall be with 2.5 sqmm copper cable. The wiring will be limited to gear tray only The Pole is to be provided with a surface mounting base plate of size 200 x 200 x 12 mm, (steel of grade E250 to IS 2062 : 2011). The mounting plate shall be provided with elongated holes (38 x 19) for alignment of the pole to suit M16 Bolt at CC 140. The Pole is to be coated with an epoxy zinc rich penetrating primer 45 microns thick and finished with polyurethane base paint for a long lasting finish with 45 microns coat in required colour. Wherever special finish of antique gold, copper or any metallic colours is done, an additional coat of lacquer is to be provided. Accessories : • Hot dip GI foundation bolts and nuts (Grade 4.6 to IS 1367) are to be supplied with the poles. • Foundation template is to be provided.

Foundation Bolt, 4 Nos of M16 x 300 mm bolt with 2 Nuts & 2 Washer

"40W WW CRI >70 or suitable, post top luminaire with total system lumen of not less than 4976lm. The luminaire housing made of die cast aluminium with dimension A9: 634mm(dia) x 1065mm height. The PCB / LED module along with driver is housed inside and covered with acrylic diffuser / white powder coated aluminium sheet and supporting brackets. Prewired with LED driver and suitable for operation on 240V, 50Hz, single phase ac supply. Luminaire should be suitable for mounting on 60mm OD pipe with cable entries for through-wiring of mains supply cable with Integral power supply and earth connection. The protection class should be IP 65. LM 79 Report to be submitted

The pole shall be tubular in shape, made with different distinct sections which shall be welded using special V groove technique with MIG welding process. The decorative base and the decorative flower on midsection of the pole will be made of GDC aluminium conforming to LM6 specification. Decorative Ornamental Base GDC housing at the pole bottom, decorative design / ring embellishments made of GDC aluminium at the mid portions with a cross arm at the top. They should be properly integrated with the pole The pole shall consist of two sections, made of MS circular tubes of ∅139.7mm x 3.6mm thick of 1000mm length at the bottom, ∅76.1mm x 2.6mm thick of 2050mm length at the second section, with steel of grade YSt 210 to IS 3601 : 2006 and shall be able to withstand the wind speed of 50 m/sec, considered in design as per IS 875 (Part 3) : 1987. The pole shall be provided with built-in control box with PDC aluminium service door and a safety chain. The control gear tray is to be prewired with Ramanuj 4way connector for loop-in loop-out arrangement and Siemens / Crabtree make MCB & connector. The gear tray wiring shall be with 2.5 sqmm copper cable. The wiring will be limited to gear tray only The Pole is to be provided with a surface mounting base plate of size 200 x 200 x 12 mm, (steel of grade E250 to IS 2062 : 2011). The mounting plate shall be provided with elongated holes (38 x 19) for alignment of the pole to suit M16 Bolt at CC 140. The Pole is to be coated with an epoxy zinc rich penetrating primer 45 microns thick and finished with polyurethane base paint for a long lasting finish with 45 microns coat in required colour. Wherever special finish of antique gold, copper or any metallic colours is done, an additional coat of lacquer is to be provided. Accessories : • Hot dip GI foundation bolts and nuts (Grade 4.6 to IS 1367) are to be supplied with the poles. • Foundation template is to be provided.

Foundation Bolt, 4 Nos of M16 x 300 mm bolt with 2 Nuts & 2 Washer

"24W LED, CRI >70, post top luminaire. The luminaire comprises of specially contoured spun aluminium body and supporting brackets with dimension A9: 634mm(dia) x 1065mm height. The PCB / LED module along with driver is housed inside and covered with acrylic diffuser / white powder coated aluminium sheet and supporting brackets. Prewired with LED driver and suitable for operation on 240V, 50Hz, single phase ac supply. Luminaire should be suitable for mounting on 60mm OD pipe with cable entries for through-wiring of mains supply cable with Integral power supply and earth connection. The protection class should be IP 65. LM 79 Report to be submitted "

The pole shall be tubular in shape, made with different distinct sections which shall be welded using special V groove technique with MIG welding process. The decorative base of the pole will be made of GDC aluminium conforming to LM6 specification. Decorative Ornamental Base GDC housing at the pole bottom, They should be properly integrated with the pole. The luminaire bracket is a specially designed decorative single arm type with an arched design, two leaves made of MS, a overhang of 700mm and mounted on to a vertical 88.9 dia pipe as a single piece assembly, which can be fitted on to a pole top and oriented in any direction. The pole shall consist of one sections, made of circular tubes of Ø88.9 mm x 2.9mm thick of 2327mm length, with steel of grade YSt 210 to IS 3601 : 2006 and shall be able to withstand the wind speed of 50 m/sec, considered in design as per IS 875 (Part 3) : 1987. The decorative arched design single arm bracket made of circular tube of Ø38.1 and overhang length of 700 mm shall be mounted on to a Ø88.9 mm circular tube in single piece formation. This single piece assembly should be capable of orientation in any direction and secured with stainless steel 304 grade allen grub screws. The bracket is to be prewired with 1.0 sqmm copper cable and with connector. The pole shall be provided with built-in control box with GDC aluminium service door and a safety chain. The control gear tray is to be prewired with Anchor make MCB & connector. The gear tray wiring shall be with 2.5 sqmm copper cable. The wiring will be limited to gear tray only The Pole is to be provided with a surface mounting base plate of size 200 x 200 x 12 mm, (steel of grade E250 to IS 2062 : 2011) and welded at the bottom of the pole. The mounting plate shall be provided with elongated holes (38 x 19) for alignment of the pole to suit M16 Bolt at CC 140. The Pole is to be coated with an epoxy zinc rich penetrating primer 45 microns thick and finished with polyurethane base paint for a long lasting finish with 45 microns coat in required colour. Wherever special finish of antique gold, copper or any metallic colours is done, an additional coat of lacquer is to be provided. Accessories : • Hot dip GI foundation bolts and nuts (Grade 4.6) are to be supplied with the poles. • Foundation template is to be provided.

Foundation Bolt, 4 Nos of M16 x 300 mm bolt with 2 Nuts & 2 Washer

"30W LED, CRI >70, post top luminaire. The luminaire comprises of specially contoured spun aluminium body and supporting brackets with dimension A9: 425mm(dia) x 415mm height. The PCB / LED module along with driver is housed inside and covered with acrylic diffuser / white powder coated aluminium sheet and supporting brackets. Prewired with LED driver and suitable for operation on 240V, 50Hz, single phase ac supply. Luminaire should be Suitable for mounting to internally threaded pipe of designation M30 with cable entries for through-wiring of mains supply cable with Integral power supply and earth connection. The protection class should be IP 65. LM 79 Report to be submitted "

Decorative Four arm, surface mounting type lighting pole of total height 9.00 meters above ground. The luminaire bracket is a specially designed decorative four arm type with an arched design, four flower made of GDC aluminium, a overhang of 2000mm and mounted on to a vertical 60.3 dia pipe as a single piece assembly, which can be fitted on to a pole top and oriented in any direction. The decorative four arm bracket holding pipe will be fitted on top with a 620mm of height cast aluminium ornamental finial. The pole shall be tubular in shape, made with different distinct sections which shall be welded using special V groove technique with MIG welding process. The decorative base and the decorative flower on mid section of the pole will be made of GDC aluminium conforming to LM6 specification. The Pole design has some special provisions with a gravity die cast aluminium Finial on pole top with a minimum height of 620 mm, Decorative Ornamental Base GDC housing at the pole bottom, decorative floral design / circular ring embellishments made of GDC aluminium at the mid portions, for architectural appeal. They should be properly integrated with the pole The pole shall consist of two sections, made of circular tubes of Ø139.7 mm x 3.6mm thick of 2000mm length at the bottom section, Ø114.3 mm x 3.2mm thick of 5357mm length at the second section with steel of grade YSt 210 to IS 3601 : 2006 and shall be able to withstand the wind speed of 50 m/sec ,considered in design as per IS 875 (Part 3) : 1987. The decorative arched design double arm bracket made of circular tube of Ø38.1 and overhang length of 2000 mm shall be mounted on to a Ø60.3mm circular tube in single piece formation. This single piece assembly should be capable of orientation in any direction and secured with stainless steel 304 grade allen grub screws. The bracket is to be prewired with 1.0 sqmm copper cable and with connector. The pole shall be provided with built-in control box with PDC aluminium service door and a safety chain. The control gear tray is to be prewired with Ramanuj 4way connector for loop-in loop-out arrangement and Siemens / Anchor make MCB & connector. The gear tray wiring shall be with 2.5 sqmm copper cable. The wiring will be limited to gear tray only The Pole is to be provided with a surface mounting base plate of size Ø280 x 16 mm, (steel of grade E250 to IS 2062 : 2011) and welded at the bottom of the pole with supporting gussets. The mounting plate shall be provided with elongated holes (48 x 24) for alignment of the pole to suit M20 Bolt at PCD 230. The Pole is to be coated with an epoxy zinc rich penetrating primer 45 microns thick and finished with polyurethane base paint for a long lasting finish with 45 microns coat in required colour. Wherever special finish of antique gold, copper or any metallic colours is done, an additional coat of lacquer is to be provided. Accessories : • Hot dip GI foundation bolts and nuts (Grade 4.6) are to be supplied with the poles. • Foundation template is to be provided.

Foundation Bolt, 4 Nos of M20 x 500 mm bolt with 2 Nuts & 2 Washer

2 x 50W, post top luminaire . The Luminaire made up of spun alumininum body with dimension A9: 634mm(dia) x 618mm height. The PCB / LED module along with driver is housed inside and covered with acrylic diffuser / white powder coated aluminium sheet and supporting brackets. Prewired with LED driver and suitable for operation on 240V, 50Hz, single phase ac supply. Luminaire should be Suitable for mounting to internally threaded pipe of designation M30 with cable entries for through-wiring of mains supply cable with Integral power supply and earth connection. The protection class should be IP 65. LM 79 Report to be submitted

90W LED, 3 Meter High Tiranga Column Light of 166MM dia, made of extruded aluminium alloy (grade 6063) with die-cast aluminium components and non corrosive SS fasteners. Non yellowing UV stabilized polycarbonate translucent diffuser. Silicone gasket .LED Make : San’an.GI mounting plate for bolting onto a foundation. Luminaire can be aligned on the mounting plate around 360°.Cable entries for through-wiring of mains supply cable. Integral power supply. Earth connection. Safety class I. Protection class IP65. CE - Conformity mark .Prewired with all accessories and suitable for operation on 240V, 50Hz single phase ac supply.

Foundation Bolt, 4 Nos of M16 x 500 mm bolt with 2 Nuts & 2 Washer

Pillar light, laser cut options of Sq.206 x 2500, IP 65, inbuilt 50W LED, 240V, colour-WW,CW,NW, Symmetrical, >80 luminaire made of extruded alu. alloy, grade 6063, die cast alu. components & SS fastners shielded/unshielded non yellowing, UV protected PC Diffuser Transluent. Foundation Base platecast iron ?250 x 12thk. 2 Nos. of M16 Nut & 2 Nos. of Plain washer, 4 Elongated holes 38 x 19 to suit M16 bolts at CC 180. LBC 10 Mt/m² (Minimum) Wind speed 50 m/s Grade of steel reinforcement: Fe 415. height of foundation above ground level (150mm) to be revised to suit the site conditions. electrical junction box. Wind speed consideration (m/Sec) 50m/sec IS 875 part 3:1987

Foundation Bolt, 4 Nos of M16 x 500 mm bolt with 2 Nuts & 2 Washer

20W Landscape Light luminaire made of die cast aluminium alloy with non corrosive SS fasteners Clear tempered safety glass diffuser retained by aluminium frame. Die cast aluminium hood cover for directional light throw. The dimension shall be 132mm x 118mm(dia) x 148mm. Luminous flux up to 1260 lm, CRI >80 Power Factor >0.9 Beam Angle 24° Operating Temperature : -20°C~+40°C Mounting spike & bracket arrangement to facilitate easy installation at any desired location. Swivel range of the luminaire in the horizontal axis +70°/-20°.Cable entries for through-wiring of mains supply cable (supplied with one metre cable length). Integral power supply, Earth connection Safety class I, CE - Conformity mark, Luminaire prewired with LED driver and Suitable for operation on 240V, 50Hz single phase ac supply. Lamp flux: 1755.16 lm with Eff of 85.09 lm/W. IP65

9W led In Ground Luminaire made up of die-casting grey powder coated aluminium, corrosion resistance with low copper content.. Hard chromeplated stainless steel 316 grade front ring. Molding shaped seal gasket. Stainless steel screws. Step tempered glass of 8mm thickness with static load resistance. IP68 PG-11 cable gland. Mechanical resistance IK10 with Protection class IP67. The dimension of fixture shall be Ø173 x 142mm. Supplied with mounting sleeve for preparing recessed opening in ground. Cable entries for through-wiring of mains supply cable (supplied with one metre cable length). Integral power supply, Earth connection Safety class I, CE - Conformity mark, Luminaire prewired with LED driver and Suitable for operation on 240V, 50Hz single phase ac supply.

3W led In Ground Luminaire made up of stainless steel housing.. Hard chromeplated stainless steel 316 grade front ring. Silicone seal gasket. Clear acrylic diffuser.Optical lens efficiency <85%.Mechanical resistance IK09 with Protection class IP65. The dimension of fixture shall be Ø158 x 122mm. Supplied with mounting sleeve for preparing recessed opening in ground. Cable entries for through-wiring of mains supply cable (supplied with one metre cable length). Integral power supply, Earth connection Safety class I, CE - Conformity mark, Luminaire prewired with LED driver and Suitable for operation on 240V, 50Hz single phase ac supply.

12W led step light Luminaire made of pressure die cast aluminium alloy of high corrosion resistance and non corrosive A2 stainless steel fasteners.. Non yellowing UV stabilized clear polycarbonate diffuser. Protection class IP65. The dimension of fixture shall be COD : 237 x 184x 90. THD: <10%, Efficiency: >85%, Light distribution: Asymentrical. LM 79 Report to be submitted

6 W LED Step light, Asymmetrical Luminaire made of pressure die cast aluminium alloy of high corrosion resistance and non corrosive A2 stainless steel fasteners. Non yellowing UV stabilized translucent acrylic diffuser. Silicon gasket. Industrial ABS plastic Installation housing for preparing the recess opening in the wall / stairs with Mechanical resisitance:Luminaire of dimension COD : 126 x 71 x83, IK08 LED Lumens: 960 lm, CRI>=80, Life span:>54K hrs MacAdam Ellipse: 3Step.Driver- PF>0.95 THD<15% Surge protection:2KV Efficiency: >75%. Cable entries for through-wiring of mains supply cable. Integral power supply. Earth connection. Safety class I. Protection class IP65. CE - Conformity mark Suitable for operation on 240V, 50Hz single phase ac supply. IP65

24W led bollard, Luminaire body of Dimension : Ø200x 972. . IP65

12 LED Flexible strip lighting systems to be Cut to the desired length12W/m IP67 120pcs 400lm/m 2700-6000K Dimension: 5m / Roll. Wattage 12W/m. Dimension 12mm 5m / Roll. 120 LEDs per metre. Integrated with SMD 2835 LEDs. Symmetrical Constant current LED driver (5Amp). CRI is >90. Protection class IP67 for LED strip. CE – Conformity mark. Low Voltage at 12V dc assures safety. Lamp flux: 830.694x1 lm . Beam angle: 120 deg.

Series Waterproof IP65 Power Supply, Wattage : 60W

24W linear in ground wall grazer Luminaire made up of extruded aluminium for better thermal management. Stainless steel grade316 front cover. Clear lines, corrosion resistant. Tempered glass diffuser for excellent diffused lighting experience throughout the life of the fixture. Supplied with extruded aluminium mounting sleeve for preparing recessed opening in ground. Cable entries for through-wiring of mains supply cable. Protection class IP67.Mechanical resistance IK07. Low Voltage at 24V dc assures safety

Two/Three WayGel Connector,Dimension : ,Wattage

24VSeries WaterproofIP65 PowerSupply, Wattage :30W

12W LED Wall Recessed Step Light, Luminaire made of pressure die cast aluminium alloy of high corrosion resistance and non corrosive A2 stainless steel fasteners. Non yellowing UV stabilized clear polycarbonate diffuser. Silicone gasket. Industrial plastic installation housing for preparing the recess opening in the wall / stairs. Cable entries for through-wiring of mains supply cable. Integral power supply. Safety class I. Protection class IP65. Dust-tight and protection against water jets. CE - Conformity mark. BIS - Conformity mark. Suitable for operation on 240V, 50Hz single phase ac supply. Cut out Dimensions: 242 x 71 x 83mm

2X18 W LED Wall Mounted Up Down Luminarie made of extruded aluminium hollow square tube with die cast aluminium frame with non corrosive SS fasteners. Toughened clear glass diffuser. Silicone gasket .Cast aluminium plate for mounting onto the wall. Surface mounting on wall using hardware after connecting to the power supply. Integral power supply. Earth connection. Safety class I. Protection class IP 65. CE - Conformity mark. BIS - Conformity mark. Suitable for operation on 240V, 50Hz single phase ac supply. Dimensions 150 x 100 x 270mm. IK 08, Citizen LED.

7W LED InGround Walk Over Luminarie, made up of aluminium, corrosion resistance with low copper content. Hard chromeplated stainless steel 316 grade front ring. Silicone seal gasket. Stainless steel screws. Luminaire hard wired with 3 x 1.0mm2 cable of 0.5mts length. Supplied with mounting sleeve for preparing recessed opening in ground. Integral power supply. Safety class I. Protection class IP65. CE - Conformity mark. Suitable for operation on 240V, 50Hz single phase ac supply. Dimensions Ø116 x 114mm

2X60W LED Flood Light with Clear polycarbonate optical cover and Excellent thermal management heat sink. Luminous flux up to 9000 ± 00 lm (60W). Efficiency up to 150 lm/W. Operating Temperature : -40°C~+50°C. Colour Rendering Index(CRI) > Ra70.Mounting bracket to facilitate proper aiming of the luminaire at desired angle. Cable entries for through-wiring of mains supply cable. Available in 40°, 60°, 90° & Type II beam angles. Integral power supply options. Safety class I. Protection class IP68 for LED Module and IP67 for LED Driver. CE - Conformity mark. Suitable for operation on 240V, 50Hz single phase ac supply. Life time of LED ( Burning hours ) : 90000Hrs. LM 79 Report to be submitted with luminarie. Dimensions: 342 x 135 x 245mm

50W LED Landscape Flood Light with Extruded aluminium hood cover integrated with module and die cast aluminium control gear. Clear polycarbonate diffuser and Heat resistant optical lens. Mounting bracket to facilitate proper aiming of the luminaire at desired angle.Cable entries for through-wiring of mains supply cable. Safety class I. Protection class : IP65. CE - Conformity mark. Suitable for operation on 240V, 50Hz single phase ac supply. LM 79 Report to be submitted with luminarie. Dimensions: 200 x 153 x 351mm

12W LED Surface Mounted Wall Light with L305 x B28 x H90mmmade of extruded aluminium with fabricated aluminium frame. Extruded aluminium housing profile designed to throw upward and downward lighting.Surface mounting on wall using hardware after connecting to the power supply.Cable entries for through-wiring of mains supply cable. Protection class IP20. CE - Conformity mark. Prewired with constant current LED driver and suitable for operation on 240V, 50Hz single phase ac supply.

12W LED Half Frame Bulkead with L 185 x B 84 x H 280mm made of die cast aluminium with non corrosive SS fasteners, Non yellowing UV stabilized polycarbonate translucent diffuser ,Silicone gasket, Cable entries for through-wiring of mains supply cable,Integral power supply, Protection class IP54, Suitable for operation on 240V, 50Hz single phase ac supply.

12W LED Glare Free Recessed Downlighter. Luminaire made of die-cast aluminium for better thermal management. Dark light technology with UGR <16. Precision engineered high quality optics & electro plated reflector. Powered by CITIZEN / CREE, CRI >90. Adjustable upto 30° / Rotatable 355°. Beam Angle : 15° / 24° / 38° with diffuser options. Protection class IP44 for LED Module. CE - Conformity mark. High PF constant current LED driver with surge and thermal protection.Cable entries for through-wiring of mains supply cable.Suitable for operation on 240V, 50Hz single phase ac supply. LM 79 Report to be submitted with luminarie. Power Factor > .95, THD < 10%, 6Kv Surge Protector, Efficiency > 87%

2'x2' luminaire of 40W with system lumen shall not be less than 3915 lm. Luminaire made of CRCA housing with aluminium front frame.High efficiency prismatic diffuser for glare free, uniform light distribution.The Luminaire Integrated with 40W LED.Cable entries for through-wiring of mains supply cable, Beam Angle 120°,Protection class IP20, UGR<19.CRI >80 Prewired with constant current LED driver and suitable for operation on 240V, 50Hz single phase ac supply. Power Factor > .95, THD < 10%, 2.5Kv Surge Protector, Efficiency > 83%

18W LED Surface Mounted luminarie with 100MM Dia and 181MM Height, made of extruded aluminium hollow circular tube with die cast aluminium frame on bottom is completely covered. Toughened clear glass diffuser. Die cast aluminium base for mounting onto the ceiling. Surface mounting on ceiling using hardware after connecting to the power supply.Cable entries for through-wiring of mains supply cable. Integral power supply. Protection class IP65. CE - Conformity mark Suitable for operation on 240V, 50Hz single phase ac supply. LM 79 Report to be submitted with luminarie. Power Factor > .95, THD < 10%, 3Kv Surge Protector, Efficiency > 85%

12W LED Open Frame Bulk head with 133 Lx 59B x 217Hmm made of die cast aluminium with non corrosive SS fasteners, Non yellowing UV stabilized polycarbonate translucent diffuser ,Silicone gasket, Cable entries for through-wiring of mains supply cable,Integral power supply, Protection class IP54, Suitable for operation on 240V, 50Hz single phase ac supply. LM 79 Report to be submitted with luminarie

Outdoor grade IP65 switch boxes with switches and power sockets

Height Adjustable Screed box for mount MT R2 1.5

Polyamide, Mounting support for GES R2

Chrome Plated (Die cast Zinc) hinged cover with locking slider

Mounting plate for GES R2 for 2 no of Type LJUC data techology support

Outdoor grade IP65 junction boxes

Junction box T 100, plug-in seal Clear internal dimensions:136x102x57 mm, IP 66

Terminal strip 1.5–6 mm², junction box, T series (Nominal crosssection mm² 1 - 4)

Junction box T 350, plug-in seal Clear internal dimensions 267x182x110 mm, IP66

Terminal strip 16–35 mm², junction box, T series (Nominal cross-section mm² 16 - 35)

IP 67 16A 5pin Power distribution unit with MCB provision

IP-67 16A,5pin Plug

Outdoor grade IP65 MCB distribution boxes

RoHS Complied, Distribution box, 5 Division Units, Empty Dimensions:190x150x125mm

RoHS Complied, Distribution box, 12 Division Units, EmptyDimensions:286x202x125mm

Switch Box for MCB Installation

3 Module Switch Box for MCB Installation

4 Module Switch Box for MCB Installation

6 Module Switch Box for MCB Installation

9 Module Switch Box for MCB Installation

10 Amp Single Pole MCB

16 Amp Single Pole MCB

PART-C HVAC WORK -H-2

AIR COOLED DX SYSTEM :

To design & supply air cooled DX type airconditioning system (one to one) complete with outdoor units comprising condenser, scroll/rotary comresssors, etc. and indoor units comprising various types of evaporative blowers, expansion device , microprocessor based remote controls, etc.

1.5 TR WALL MOUNTED UNIT (2W +1S) (3-STAR)

Note:- Two working + One stand by AC unit on sequence controller in server room.

To design & supply of air cooled TREATED FRESH AIR unit with DX type coil for cooling only, comprising 6-row / 8-row coil & following air discharge and refrigeration capacities at an external static pressure of 20 mm wg, expansion device, microprocessor based remote controls and complete with outdoor units comprising condenser, scroll/rotary comresssors, complete in all respect.

7.5TR/1300 CFM @ 20 mm ESP, ceiling Suspended TFA Unit with 100% Fresh Air along with 7.5 TR CDU, control panel, piping cabling etc.

5.5TR/1000 CFM @ 20 mm ESP, ceiling Suspended TFA Unit with 100% Fresh Air along with 5.5 TR CDU, control panel, piping cabling etc.

DX SYSTEM INSTALLATION:

Lifting/ shifting, installation, testing, and commissioning of outdoor/indoor units including M.S. stand,refrigarant charging/top up, fixing of remote control etc.complete in all respect of following capacity unit:

1.5 TR WALL MOUNTED UNIT (2W +1S)

Note:- Two working + One stand by AC unit on sequence controller in server room.

TFA Unit

1300 CFM with 7.5 tr ODU

1000 CFM with 5.5 tr ODU

Supply and installation of copper refrigerant piping of required sizes duly insulated with closed cell elastomeric insulation thickness as specified by manufacturer,as per pipe size and cabling between indoor and outdoor complete with proper supports etc for following capacity unit. All related civil work such as making hole, chasing in wall, shall be inclusive in the quoted price.

1.5 TR WALL MOUNTED UNIT (2W +1S)

TFA Unit

1300 CFM with 7.5 tr ODU

1000 CFM with 5.5 tr ODU

To supply, install, test and commission UPVC drain pipes duly insulated with 6 mm thick nitrile rubber and 'U ' traps from indoor units to nearest drain point.

25mm dia.

AIR DISTRIBUTION SYSTEM

AIR COOLER

Suppling, installing, testing and commissioning of Double skin construction CELLULOSE FILL AIR COOLER giving 90% efficiency at 500 FPM air velocity across pads, factory assembled complete with 18 g stainless steel 304 water tank, fans, Cellouse fill, water distribution header, valves , quick fill, G.I./ CPVC internal piping, pump, strainers, and necessary fitting.The quoted price shall also include box type pre filters and 2 bend PVC drift eliminators. The fan section shall have imported DIDW forward curved centrigugal fan, drive set with v belt, and motor. The motor shall be aligned with blower and suitable for 415 volts, 50 cycles, 3 Phase power supply. External Static pressure shall be 30 mm WG or need to be confirmed as per ducting by HVAC vendor before installation. Make: ZECO, Edgetech.

CONTROL PANELS FOR AIR COOLER

Design, manufacture, supply, installation, testing & commissioning of the following cubicle type, dead front, sheet steel, wall mounted control panels, including anchoring into the wall, wiring terminating into MCB & copper earthing, in each panel shall be provided by the electrical contractor.Panel shall be suitable for weather proof application. Make : Zeco, Edgetech, Symphony, Evapolar.

All wiring & copper earthing of motors from panel shall be included.

The panel shall be include the following components & accessories.

MCB as per the ratings given below, suitable for motor duty and able to withstand fault level of 20KA.

DOL / SD starter as per HP rating

Terminal block for power distribution as required.

Contactor, overload relay with built in single phasing protection (only for DOL & S/D starter)

Phase indicating lights & indicating light for 'ON' status.

Time delay relay for delayed automatic restart of motor.

For on / off / remote and local operation, 3 pole single phase throw switch shall be provided in each unit panel to facilitate overide of the automatic operation

Remote start & stop facilities to be provided for each panel

The number of control panels shall be as follows:

2.0 - 7.5 HP DOL starter

AIR DISTRIBUTION

Supply, installation, testing and commissing of INLINE FANS for Toilet/ Pump room Exhaust air system. Each fan shall be complete with totally enclosed fan cooled motor, drive, motor mount & vibration isolators. Fan static pressure shall be 20 mm WG. Make:Maico, Green heck, Caryaire, Systemair Lau

450 mm dia 1400 RPM fan suitable for 220 +(-)6% volts 50 cycles, 1 Phase AC supply

SITE FABRICATED DUCT

Supply, fabricating, installating, and testing of site Fabricated ducts of following thickness including necessary supports flexible hangers with isolators, nut bolts, gasket splitter damper vanes, etc. complete as per specifications in accordance with the approved shop drawings and required by the specifications. Make: Tata, Jindal

TFA duct

24 gauge galvanised sheet

Air cooling duct

24 gauge galvanised sheet

22 gauge galvanised sheet

Toilet and ventilation duct

24 gauge galvanised sheet

22 gauge galvanised sheet

FLEXIBLE CONNECTION

Supply, fabricating, installing, and testing of double canvas flexible connection constructed of fire resistant material as per the drawings /specifications.

GRILLE / DIFFUSER

Supply, installation, testing and commissioning of supply / return aluminium air grille/diffusers as per approved shop drawings and colour. Each grille/diffuser will be equipped with removable core and a aluminium volume control damper which will be key operated complete as per specifications and drawings. Make: Carryaire, Green heck, Ravi star, Air Master,Mapro

Powder Coated aluminium linear/square grille with aluminium damper.

Powder coated extruded double louver aluminium air grille with damper for air cooling of approved colour and shade.

Aluminium powder coated air grille with damper for exhaust of 150 x 150mm

Exhaust/ fresh air louvers with bird screen.

Fire smoke damper made of heavy gauge galvanised steel having multi blade construction,90 min fire rating, with UL stamped thermal cut-off with spring return electric actuator motor.

THERMAL INSULATION

Duct Insulation Make:Armaflex, k- flex,superlon,superlon,UP Twiga, Owens Corning, Lloyd insulation, Beardsell ltd, Cooline,supreme

Supply, installation & testing of duct insulation with fiber glass wool with factory faced aluminium sheet (Density not less 32kg/m³) on G.P. sheet deck as per specifications.

Supply, installation & testing of duct insulation with 13mm thick Nitrile Rubber insulation (Density 50-60 kg/m³ ) on TFA supply air ducts.

Supply, installation & testing of duct insulation with 9mm thick Nitrile Rubber insulation (Density 65 kg/m³ ) on supply air ducts for air cooling.

Supply, installation & testing of 19mm thick nitrile rubber insulation (Density 65kg/m³ ) covered with glass cloth & three coats of UV protected paint complete in all respect.(For Exposed Cooling Ducts only)

50 mm thick

PART-D Fire Fighting NON BSR-H-3

Supply, installation, testing and commissioning of Manufacturer fitted and tested FLD - Mini Fire system comprising of the following:

Vertical Inline multistage centrifugal pump suitable for operation on 415 volts ± 5%, 3 phase, 50 HZ A.C supply.

The pump casing shall be SS 304, shaft shall be SS 316 & impeller shall be SS304 and with Mechanical seal. The system shall be complete with necessary accessories isolation valve on suction & delivery side, pressure gauge, pressure switch-recirculation valve, pressure transmitter, Flow switch, a pressure tank to manage start - stop etc mounted on a MS common base frame complete in all respect.

Squirrel cage induction motor TEFC type IE2 class for operation on 415 V, 3 phase 50 HZ AC supply for the above pump with speed of 2900 R.P.M.

Mini Fire system Skid mounted Panel comprising the following:

Microprosessor based starter panel with IP55 protection included necessary wiring, cable alleys, earthing, Adequate MPCB, contractor, relays,switchgears, cooling fan, Dry run protection, Over load protection, earthing, Indication lamp for pump running, PERIODIC AUTO TEST PROVISION complete in all respect. Panel should be from pump manufacurer.

Panel should have auto delayed operation features

Multiple mode of operation ( Auto test, auto start mannual stop, auto re-pressurization, auto stop , auto delay )

For pump defined above & of duty as follows :

Flow : in LPM as per site requirement ( 400 - 450 LPM )

Head : In Mtr as per site requirement ( 40 - 45 Mtr. )

Cost of 1 Set

Bidder Name

Amount

Raj Electricals(GSTN-08AGBPS1419A1ZV)