CA No GE(H)-31/2022-23 PROVN OF STONE HARD STANDING 1000 SQM AND COVERED SHED OF SIZE 12M X 13M, 12M X 23M AND 12M X 18M WITH STONE SETT FLOORING IN CERTAIN UNIT IN THE AOR OF AGE B/R II UNDER GE HISAR AT HISAR MIL STN

Amount

Excavation over areas not exc 1.5m deep and getting out in hard / dense soil all as specified and as directed.

Removing excavated soil/material exc. 250m but not exc. 500 m and depositing where directed complete all as specified.

Excavating in trenches not exc 1.5 metre wide and not exc 1.5 metre in depth for foundation or for shafts, walls, manholes, laying of cables, pipes etc not exc 10 Sqm on plan and getting out in soft/loose soil.

Returning, filling in, including spreading, leveling watering and well ramming in layers not exc 25 cm thick in soft/loose soil.

Removal of excavated soil/ material to a distance not exc 50 metre and depositing where directed at a level not exc 1.50 metre above the starting point complete all as specified.

Excavating in post holes (or similar holes) each not exc 0.50 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exc 25cm, watering, and removing surplus soil to a distance not exc 50 m and making good surface in soft/ loose soil all as specified.

M&L for PCC 1:4:8 type D2 using 40 mm graded crushed stone aggregate in foundations, filling and mass concrete all as specified.

S&F mild steel framed work in tubular trusses using ERW or induction butt welded tubes conforming to I.S 1161-1979 Grade St-240 including necessary welding, bolting, special shaped washer, clamps, cleats etc. complete all as specified & as directed.

S&F rolled mild steel work as in Plates (plain or chequered) channels. Square cut or notched (ordinary and counter sunk) forming holes, without any attachment including necessary welding etc. conforming to Gde E-250 (Fe 410-W) quality `A’ all as specified and as directed.

S&F mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 5cm and not exc 10 cm long and dia of neck 11mm to 15mm complete all as specified.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws or ‘L’ type or ‘J’ type or cranked hooks bolts complete all as specified & directed.

Rolling and consolidating formation surfaces in cutting with power roller exc 8 tonne and not exc 12 tonne complete all as specified & directed.

M & L for Soling (or sub base) 225mm thick with broken boulders or quarried stone, inter stices filled, surface formed and rolled and consolidated to required gradient and camber complete all as specified & directed.

M&L for 100mm thick PCC (1:2:4) type B2 using 40 mm graded crushed stone aggregate as in sub base, surface finished fair and even complete all as specified.

M&L stone sett flooring with hard granite stone setts of size 200 to 250mm long, 150 to 200mm wide, 150mm deep and sides dressed, bedded in cement mortar 1:3, joints 20mm thick; grouted in cement mortar 1:2 with an admixture of metallic floor hardner 5% by weight of cement and struck flush complete all as specified & as directed. Make of metallic floor hardener : - IRONITE / HARDONATE

M&L Edge stones to flooring with hard granite stone setts of size 250 to 300mm long x l50 to 200mm wide, and 450mm deep and sides dressed, bedded in cement mortar 1:3, joints 20mm thick; grouted in cement mortar 1:2 with an admixture of metallic floor hardner 5% by weight of cement and struck flush complete all as specified & as directed. Make of metallic floor hardener : - IRONITE / HARDONATE

M&L for preparation of new steel and iron surfaces of any description over 10 cm in width or girth and applying two coats of synthetic enamel paint of approved tint over a coat of red oxide primer complete all as specified.

M&L for Sand cushioning 230mm thickness with dry sand (one layer of 80mm thickness before laying of cable and other layer of 150mm thickness afterlaying of cable) and punned down to 180mm after laying of cable in trenches for protection of cable complete all as directed. Note :- For the purpose of payment only punned thickness shall be measured.

M&L for brick covering to underground electric cable using sub class ‘B’ bricks, laid dry, flat, perpendicular to the direction of cable etc complete all as specified and directed. .

Supply , laying , jointing, testing and commissioning of cable of size 10 sqmm 2 core LT underground cable , 1100 volts grade, XLPE insulated and PVC sheathed, armoured heavy duty with multistrand aluminium conductors as per IS 7098 (Part-I), laid in trenches /fixed on wall /floor /road /culverts /pole or encased in GI pipe complete all as specified. Note : Sand cushioning, cable protection, GI protection pipe, clamps, jointing kits and excavation & earth work shall be measured & paid for separately.

S&F Sub main wiring with two single core cable PVC insulated unsheathed of copper multi stranded conductor FRLS cable of size 1.50 sqmm, 1100 votls grade drawing through and including concealed conduit 25 mm dia medium duty including acessories such as Tee, bend, Elbow etc, ISI marked with and including PVC insulated 1.50 sqmm unsheathed multistranded FRLS copper conductor cable for earth continuity and connected to common earth dolly including fixing the conduit on pipe/angle with necessary jointing clamps etc complete all as specified and directed. Note:- Two lengths of 1.50 Sqmm cable, one length of 1.50 Sqmm cable and one length of PVC conduit will be measured as one length.

S&F sheet metal enclosure distribution board SP&N, 4 way, double door, powder coated, protection class IP-42, suitable for mounting MCB, DBs conforming to IS-13032, IS-8632, BS-5484 with min 200 Amp rating copper bus bar, complete all as specified & directed. Make :- Indo Asian Cat Part No 810319 or equivalent of makes mentioned in list of makes here-in-after .

S & F MCB SP, 6 to 32 Amps 240 Volts , 'C' curve, 10 KA, complete. Note :-Make of MCB shall be same of that DB.

S & F MCB SPN, 32 Amps 240 Volts , 'C' curve, 10 KA, complete. Note :-Make of MCB shall be same of that DB.

S&F ceiling rose surface bakelite 65mm x 50mm, 3 terminals with back plate etc complete all as specified and directed.

S&F LED tube light fitting 1x36/40W, regal batten for LED including ultra bright glass LED Tubelight with very high efficacy, single / double side connection all as specified and directed.

S&F asesthetically designed LED street light fitting 35 Watt system wattage for energy saving having IP 66 degree of protection with minimum system efficiency as >85%, made of pressure die cast aluminum hosing powder coated in graphite grey and heat resistant toughened glass with excellent thermal management LED shold have lens optics and vandal proof prismatic poly carbonate covers for ensuring efficient optics and uniform distribution of light fitting should have operating voltage range of 120-270 Volts, THD<10%, P.F. >0.95, fitting should have in built surge protector of 5 KV and CRI>70 with CCT 5700 K and including 0.5 sqmm flexible copper multistranded conductor cable fixed on wall / pole including security light bracket made to shape out of GI pipe 40mm dia light grade 1.5m length and fixed with MS clamps of size 40x5mm - 2 Nos, nuts, bolts and washers fixed on wall all as specified and directed. Make : Cat Part No ENDURACITYLITEPLATPLUSSL35WLED757SASYBOPC of Endura Citylite Platinum Plus of Havells or TRP-400-35-57-SL-LM-NSR of Crompton or equivalent make as mentioned in Appx 'C' list of makes here-in-after.

M/S RAJESH KUMAR & SONS