Major Renovation and Modification works of S.B. Boginodi (Assam-437) along with re-powring of Engines against Guwahati Umananda river cruise service.

Amount

Dry docking of vessel/boat carefully and placing over roller/blocks for major repairing works without causing any damage to the boat as per direction

Up to 10 ton

Additional 20 Ton

Supplying/Providing of wooden blocks up to the sizes (75x45x30) cm under lifted vessel/boat etc. including necessary wooden packing per direction complete.(Non-Sal)

Cutting /removing old damaged plate, angle, etc. by using gas including the cost of labour as directed. 6 mm plate

Supplying of I.S. Grade 2026 Mild Steel Plate of required size and specified thickness in keel , bottom hull, side hull, transom, side keelson etc. for the hull erecting in position by cutting welding straighten etc. in proper shape and size and welding the same including all cost of labour, material etc. complete as directed. (5mm & above)

Providing M S Plate cutting into required size fitting & fixing by welding in superstructure wheel house, passengers accommodation, cabin etc. including cost of labour and materials complete. M. S. Plate below 5mm thick

Providing frame work in hull & superstructure by cutting M.S. angle, M.S. Rod, channel etc.in required sizes welding the same including all cost of labour and materials complete.

Providing steel Fender cutting from M.S. pipe having 6 mm thick half round fitting and fixing by welding including cost of labour and materials complete. (20mm dia pipe )

Providing Double Bollard including making/ repairing of its base frame.

Double Bollard

Single Bollard

(i) Providing G.I. pipe connection in the service water line with required G.I. pipe socket bend, tee, stop-cock, bib-cock, valve etc. complete as per direction.

12 mm dia pipe

25 mm dia pipe

37 mm dia pipe

Supplying fitting and fixing M.S pipe railing in deck and superstructure of vessel/boat etc. complete as direction. (M.S.Pipe)

Applying priming coat: 13.50.3- With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/ steel works

Painting on G.S. sheet with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : 13.53.1 New work (two or more coats) including a coat of approved steel primer but excluding a coat of mordant solution

a) Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed steel conduit, with piano type switch, phenolic laminated sheet, suitable size MS box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required

Short point

Medium point

Supplying including fitting & fixing of electronics igniters complete as direction and specification by the Deptt.(Philips/Hevells/Bajaj of equivalent make)

b) Providing fitting and fixing in position 6 mm thick Bison panel (cement bonded particle board) partition wall on both faces of the timber frame of 1st class local wood (Hollock/Bonsum/Sundi) with horizontal and vertical batten of size 50mmx 80 mm spaced at not more than 1.20 m apart, with necessary nails,wood screws, bolts etc. including painting (one coat primer and two coats painting)as necessary complete as directed by the Department for all levels. One side laminated

Letter writing on Board as per direction

Ashok Stambha

Rhino

Providing , fitting & fixing Anti Skid Embossed Venyle flooring (1.50m width x 1.5-2.0 mm thick) commercial category of required colour recommended area of usage on floors (steel/wooden/PCC) etc. fixed with adhesive as recommended by the manufacturer, as per direction. For both lower & upper deck.

Providing and fixing in position suspended false ceiling using E-Grid (exposed ceiling suspension 2430 system) of grid size 600 mm x 600 mm /1200mm x 600 mm with main runner 38 x 24 mm , cross tee 29 mm x 24 mm & wall angle 24 mm x 24 mm .Using 4mm/6mm thick High Pressure Steam Cured . Non Asbestos Fibre Cement Board as per IS 14862, to be placed in a grid of G.I. system duly suspended with 4 mm/6 mm dia G.I/M.S bar hanger fixed with steel dash fasteners or iron purlin from the roof with adjustment clip providing positions for light fixtures, air conditioning diffuser and ducts, sprinklers, smoke detectors etc. The main runners to be secured to structural soffit by hanger @ 1220 mm maximum c/c . The last hanger at the end of each main runner should not be placed at more than 450 mm from the adjacent wall. Flush fitting 1220 mm cross tee to be interlocked between main runners @ 610 mm c/c so As to form 600mmx600mm /1200mmx 600mm grid, all complete as per the drawing & direction of engineer-in –charge. Finally if specified boards are to be painted with 2 coats of acrylic emulsion paint of approved shade/make over a coat of cement primer before installing it on the grid. Designer Ceiling of Everest make or equivalent as directed by the department. (ii) Using 6 mm thick FC Board

Rudder Repairing

(i) Re-metalling, machining, cutting, straightening of rudder shaft as per direction at coupling end and at plumber block

(ii) Re-metalling of coupling inner

(iii)Rudder coupling Nut & Bolts

(iv)Rudder shaft lock new fitting 12 mm thick M.S. plate.

(v) Adjusting Screw

(vi)Rudder shaft & rudder plate straightening by hydraulic pressure.

(vii)Rudder Chain

(viii) D.Shackle

(ix) G.M.Bush for rudder shaft(60mm)

(x) G.M. Stud making

(xi) Plumber block with bearing (60mm)

(xii) Rudder stock with guardant

(xiii) Propeller shaft machining, turning cutting and polishing and re-metaling where necessary including straightening.

(xiv) Coupling inner surface re-metaling cutting turning machining as per direction.

(xv) Peopeller shaft key making

(xvi) Propeller check nut making

(xvii) Cotter Pin

(xviii) Propeller shaft straightening by hydraulic pressure.

(xix) Propeller shaft screw blade reshaping

Cut-less Bush---- OD-100 mm ID—60 mm FD—150 mm Length----300 mm

Propeller screw (Manganese Bronze) 3 blade with reqd. pitch. Size---50 cm to 70 cm

Group-A (Port side Engine) No. 21220620716

Cylinder head gasket. 408530074

Value spring IGL 400240001

Cylinder barrel 006100122111

Piston ring set std YDA 4614009

Piston YWA MK-6 2014043

Push rod YDA series 1700104011

Set of “O” ring 2272116

Valve guide with groove 005600100018

Valve seat insert (inlet) STD 2200100125

Valve seat insert (exhaust)STD 2200100126

Inlet valve YDA 001200103117

Exhaust value YDA 001200103118

Gasket for thermostat IGL 408530094

Complete set of joint 004672102

Push rod sleeve 001200104016

Air filter element 106900000038

Connecting rod bearing set IGL 404300016

Connecting rod bolt IGL 40150034

Connecting rod nut IGL 40150024

Gudgeon pin 03707148821

Connecting rod bush IGL 404310014

Crank shaft bearing IGL 404320046

Crank shaft gear 001600170028

Cam shaft bush IGL 404320014

Oil seal 001700132022

Thrush ring IGL 403400014

V. belt YDA 90611031

V. belt YDA 90611032

Exhaust manifold 6YDA 000267460011

Set of Hose 6Y2DX 00004671039

L.O. pressure gauge pipe 001240320773

L.O. filter 001200371115

Fuel filter element 001100240107

Injector nozzle 003737230852

Injector tube 0017001000015

Ammeter 01700530031

Battery cable +ve 001240530059 (78’’ long)

Battery cable -ve 001240530061(78’’ long)

Banjo (Special) 707320007

Hose clip no 1 (30 to 40 mm)90021203

Spring washer (5/8’’)

Bolt HEX ¼ UNF 1’’ long

Exhaust bend 1100460243

Exhaust pipe 1100463105

Tail pipe exhaust silencer 1100463211

Pipe injector overflow 1110251016

Pipe tank to filter 1110251129

Fuel pipe 2YWA 34032 SP 120340031

Thrust washer .005’’ O/S 1200178002

Fuel fed pump 1200207190

Injector pipe 1240220716

Injector pipe 1240220717

Injector pipe 1240220718

Pipe fuel pump to injector 1240220726

L.E. Bearing HD YD 1700141050

Main Bearing (Narrow)STD 1700178060

Main Bearing (wide)STD 1700178070

Specification of Item

Injector complete EM0107230015

Delivery valve 9411038578

Nozzle element 9430034270

Bearing 30204

Coupling fuel pump 001700202024

Nozzle holder flange YDA EM 0207230022

Calibration of fuel pump

Calibration of nozzle

Specification of Item

Cylinder head testing

Con. Rod re-boring and remaking

Con. Rod bushing fitting

Con. Rod alignment checking

Crankshaft bend testing

Main bearing setting

Cam shaft bushing fitting

Valve seat cutting & fitting

Valve guide remarking & fitting

Labour charge for Overhauling of main engine including replacing and assembling of engine spares starting the engine and test run for 24 hours.

(3) Water Pump Repairing (Port side)

Water pump bearing

Water pump shaft

Water pump bushing

Water pump gasket set

Water pump impeller

Water pump overhauling cost

Self Starter (24 Volt) (Port side)

Main field coil changing

Auxiliary field coil changing

Metal bush changing

Clutch Disc changing

Carbon brush changing

Carbon holder changing

Carbon spring changing

Solenoid switch changing

Contact point changing

Bendix pinion changing

Kali changing

Self starter gasket with bolt & nut changing

Overhauling cost

Dynamo (24 Volt) (Port side)

Armature changing

Field coil tapping, varnishing & repairing

Armature commutator changing

Armature check nut changing

Bearing changing

Carbon brush changing

Dynamo end point changing

Pole piece screw changing

Long bolt & nut changing

Overhauling cost

(4) Day to Day maintenance materials

Cotton waste

Markin cloth

Battery terminal

Battery clamp

Group-B (Std. side engine) No-21220620712 of SB Boginodi of Commercial Service.

Cylinder head gasket. 408530074

Value spring IGL 400240001

Cylinder barrel 006100122111

Piston ring set std YDA 4614009

Piston YWA MK-6 2014043

Set of “O” ring 2272116

Valve guide with groove 005600100018

Valve seat insert (inlet) STD 2200100125

Valve seat insert (exhaust)STD 2200100126

Inlet valve YDA 001200103117

Exhaust value YDA 001200103118

Gasket for thermostat IGL 408530094

Complete set of joint 004672102

Push rod sleeve 001200104016

Air filter element 106900000038

Connecting rod bearing set IGL 404300016

Connecting rod bolt IGL 40150034

Connecting rod nut IGL 40150024

Gudgeon pin 03707148821

Connecting rod bush IGL 404310014

Crank shaft bearing IGL 404320046

Oil seal 001700132022

Thrush ring IGL 403400014

V. belt YDA 90611031

V. belt YDA 90611032

Set of Hose 6Y2DX 00004671039

L.O. pressure gauge pipe 001240320773

L.O. filter 001200371115

Fuel filter element 001100240107

Injector tube 0017001000015

Battery cable +ve 001240530059 (78’’ long)

Battery cable -ve 001240530061(78’’ long)

Banjo (Special) 707320007

Hose clip no 1 (30 to 40 mm)90021203

Spring washer (5/8’’)

Bolt HEX ¼ UNF 1’’ long

Exhaust bend 1100460243

Exhaust pipe 1100463105

Tail pipe exhaust silencer 1100463211

Pipe injector overflow 1110251016

Pipe tank to filter 1110251129

Fuel pipe 2YWA 34032 SP 120340031

Thrust washer .005’’ O/S 1200178002

Fuel fed pump 1200207190

Injector pipe 1240220716

Injector pipe 1240220717

Injector pipe 1240220718

Pipe fuel pump to injector 1240220726

L.E. Bearing HD YD 1700141050

Main Bearing (Narrow)STD 1700178060

Main Bearing (wide)STD 1700178070

For fuel pump Repairing:-

Injector complete EM0107230015

Delivery valve 9411038578

Nozzle element 9430034270

Bearing 30204

Coupling fuel pump 001700202024

Nozzle holder flange YDA EM 0207230022

Calibration of fuel pump

Group-B (labour charges)

Cylinder head testing

Con. Rod re-boring and remaking

Con. Rod bushing fitting

Con. Rod alignment checking

Crankshaft bend testing

Main bearing setting

Cam shaft bushing fitting

Valve seat cutting & fitting

Valve guide remarking & fitting

Labour charge for Overhauling of main engine including replacing and assembling of engine spares starting the engine and test run for 24 hours.

FOR WATER PUMP REPAIRING (Std. Side) :-

Water pump bearing

Water pump shaft

Water pump bushing

Water pump gasket set

Water pump impeller

Water pump overhauling cost

SELF STARTER (24 VOLT ) (Std. Side)

Main field coil changing

Auxiliary field coil changing

Metal bush changing

Clutch Disc changing

Carbon brush changing

Carbon holder changing

Carbon spring changing

Solenoid switch changing

Contact point changing

Bendix pinion changing

Kali changing

Self starter gasket with bolt & nut changing

Overhauling cost

DYNAMO (Std. Side Engine) (24V)

Armature chinging

Field coil tapping, varnishing & repairing

Armature commutator changing

Armature check nut changing

Bearing changing

Carbon brush changing

Dynamo end point changing

Pole piece screw changing

Long bolt & nut changing

Overhauling cost

DAY TO DAY MAINTENANCE MATERIAL

Cotton waste

Markin cloth

Battery terminal

Battery clamp

Diesel for washing spares

Mobile for changing