A/R M/O various WSS/FIS under Jal Shakti Sub-Division Udaipur Distt Lahaul Spiti HP

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of cantering, shuttering, finishing and reinforcement - All work up to plinth level : 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) in all leads and lifts complete as per the direction of Engineer-in- Charge.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level in Mild steel and Medium Tensile steel bars or as per the direction of the Engineer-In-Charge.

Providing Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:4 (1 cement : 4 coarse sand) in all respect and as per the entire satisfaction of Engineer-In-Charge.

Stone soling / boulder filling, dry hand-packed, under floors / behind retaining walls, complete in all respects, including all leads and lifts, and to the entire satisfaction of the Engineer-in-Charge

Centering and shuttering including strutting, propping etc. and removal of form for all heights:

Foundations, footings, bases of columns, etc. for mass concrete or as per the direction of the Engineer-In-Charge.

Suspended floors, roofs, landings, balconies and access platform or as per the direction of the Engineer-In-Charge.

Steel work welded in builtup sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works i) Kitchen Truss (10.25.2)

Providing and fixing corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 1.00 mm thick with zinc coating not less than 275 gm/m² in all lead and lift and entire satisfaction of Engineer-In-Charge.

15 mm cement plaster on the rough side of single or half brick wall of mix : Cement Mortar - 1:4 (1 cement: 4 fine sand) in all lead and lift and entire satisfaction of Engineer-In-Charge.

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately). Second class teak wood

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete in all lead and lift and as per the direction of Engineer -In-Charge.

Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade : Two or more coats on new work complete in all lead and lift and as per the direction of Engineer -In-Charge.

Applying priming coat : With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood) in all lead and lift and as per the direction of Engineer -In-Charge.

Painting wood work with Deluxe Multi Surface Paint of required shade two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @0.75 ltr/10 sqm of approved brand and manufacture in all lead and lift and as per the direction of Engineer -In-Charge.

Applying priming coat With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/ steel works in all lead and lift and as per the direction of Engineer -In-Charge.

Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer (primer to be measured and paid for seprataly) of approved brand and manufacture in all lead and lift and as per the direction of Engineer -In-Charge.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm in all lead and lift and as per the direction of Engineer -In-Charge.

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shade ( Area of slab over 0.50 sqm) in all lead and lift and as per the direction of Engineer -In- harge. (Item No. 8.2.2.2)

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS: 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : Kitchen sink without drain board, 610x510 mm bowl depth 200 mm in all respect as specified & directed by Engineer-In-Charge. (Item No. 17.10.2.1)

Providing and fixing C.P. brass bib cock (Mixer tap) of approved quality conforming to IS:8931 : 15mm nominal bore in all lead and lifts and entire satisfaction of Engineer-In-Charge. (Similar Item No. 18.50.1)

Providing and placing on terrace (at all floor levels) polyethylene water storage tank 1000 liter, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank in all leads and lifts as per direction of Engineer-In- Charge. (Item No. 18.48)

Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes confirming to IS:15801, UV stabilized & anti - microbial fusion welded, having thermal stability for hot & cold water supply, including all PP - R plain & brass threaded polypropylene random fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in- harge. (Item No. 18.5.1)

PN - 16 Pipe, 20mm OD (SDR-7.4)

Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes confirming to IS 15801, UV stabilized & anti - microbial fusion welded, having thermal stability for hot & cold water supply, including all PP - R plain & brass threaded polypropylene random fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes testing of joints complete in all leads and lifts as per direction of Engineer-In- Charge. (Item No. 18.4.2 & 18.4.3)

Internal Exposed on walls - PN - 16 Pipe, 25mm OD (SDR-7.4)

Internal Exposed on walls - PN - 16 Pipe, 32mm OD (SDR-7.4)

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid in all respect as specified & directed by Engineer-In-Charge. (Item No. 17.2.1)

Providing and installation of stationary storage type Instant Electric water heater (Geyser) of various sizes by means of Expansion-bolts with nuts and washers, including embedding of expansion-bolts in the wall, providing and fixing of Nonreturn valve, Dead weight safety valve, 2 No C.P. connection rods 18" long, making good the damages, electrical connections, safety valve connections, testing and commissioning etc. as required:- 3 Liter capacity water heater in all leads and lifts.

Providing and fixing of Ball Valve - Plastic Body complete in all respect as per direction and to the entire satisfaction of Engineer-in-Cherge.

25 mm dia

32 mm dia

Providing and fixing of PPR Elbow 90D complete in all respect as per direction and to the entire satisfaction of Engineer-in-Cherge.

25 mm dia

32 mm dia

Providing and fixing of PPR Socket complete in all respect as per direction and to the entire satisfaction of Engineer-in-Cherge.

25 mm dia

32 mm dia

Providing and fixing of PPR Equal Tee complete in all respect as per direction and to the entire satisfaction of Engineer-in-Cherge.

25 mm dia

32 mm dia

Providing and fixing of PPR Union complete in all respect as per direction and to the entire satisfaction of Engineer-in-Cherge.

25 mm dia

32 mm dia

Wiring for light point / fan point / exhaust fan / call bell point with 1.5 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit and earthing the light point with 1.5 Sq.mm. HRFRLS/PVC insulated single core copper conductor cable as required. Group "C"

Wiring for light plug with 2x1.5 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit along with 1 No.1.5 Sq.mm. HRFRLS/PVC insulated single core copper conductor cable for earthing as required.

Supplying & Fixing of G.I. modular boxes of following sizes along with modular base and cover plate for modular switches in recess as required:-

8 modules (120mmx135mmx60mm)

Wiring for circuit/sub-main with following size PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit along with 1 No. HRFRLS/PVC insulated single core copper conductor cable of same size for earthing as required.

2 x 1.50 Sq. mm.

2 x 2.50 Sq. mm.

Supplying and Fixing following rating Modular switch /socket in the existing switch box / cover plate including connections etc. as required.

S.P. 5/ 6 Amps one way Modular switch.

5 pin, 5/ 6 Amps Modular socket outlet.

S.P. 15/ 16 Amps one way Modular switch.

6 pin,15/16 Amps Modular socket outlet.

Providing and installation of exhaust fan of following sizes in the existing opening, including making the hole to suit the size of the above fan, making good the damages, connections, testing and commissioning etc. as required:- Light duty, (Domestic) 300 mm sweep