Construction of DMFT Secretariat (Conference Hall and 02 rooms in DIC building Una Distt. Una (HP).

Amount

Excavation in earth work in all heights and depth in all kinds of soils, including saturated soil comprising of pick work, jumper work, and blasting work both in soft and hard rock with chiselling and wedging out of rock (where blasting is prohibited) and their intermediate classification of soils including, dewatering wherever required, setting out to required lines, levels as shown on the drawing and directed by the Engineer -in-Charge at site. and disposal of surplus earth in all leads and lifts.

Providing and laying cement concrete 1:4:8 (1 cement:4 sand:8 graded stone aggregate 40mm nominal size) and curing complete including cost of form work in:Foundation and plinth and wall including carriage of materials upto all leads and lifts.

Providing and laying Boulder filling under the floors complete in all respect.

Providing form work with steel plates 3.15 mm( three decimal fifteen millimeter ) thick welded with angle iron in frame of 30x30x5mm(thirty into thirty into five millimeter) so as to give a fair finish including centering shuttering strutting and propping etcetera with wooden battens and ballies for all heights of propping and centering below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in including carriage of materials upto all leads and lifts. (a). Foundations, footings & bases of columns etc., and mass concrete.including enitre carriage of material within all leads and lifts and other incidentials as per the direction by the Engineer-in-charge .

(B).columns, pillars, posts and struts square rectangular or polygonal in plan in any height including entire carriage of material within all leads and lifts and other incidentials and as per the direction by the Engineer-in-charge .

(C). Lintels, beams, plinth beams, girders, bressumers and cantilevers including enitre carriage of material within all leads and lifts and other incidentials as per the direction by the Engineer-in-charge .

(D).Suspended floors, roofs, landings, balconies, fecia , moulding and access platformincluding enitre carriage of material within all leads and lifts and other incidentials as per the direction by the Engineer-in-charge .

(e). Stair cases with slopping or stepped soffits including landings etc.including enitre carriage of material within all leads and lifts and other incidentials as per the direction by the Engineer-in-charge .

(f). Edges of slab, chajjas etc. including carriage of materials upto all leads and lifts.

(g). Vertical surfaces such as walls (any thickness) partitions and like i/c attached buttresses, pillasters, plith and string courses and the liike including carriage of materials upto all leads and lifts.

Providing and laying cement concrete 1:1.5:3 (One cement : one point five sand :Three graded crushed stone aggregate 20mm nominal size)( Twenty milimetre) and curing complete, mixing the material in mechanical mixture and compacting the concrete with viberator complete excluding cost of form work and reinforcement for reinforced concrete workFoundations, footings, bases of columns and the like and mass concrete. including carriage of materials upto all leads and lifts.

Providing and layingReinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement :1:1.5:3 (1 cement : 1.5 coarse sand): 3 graded stone aggregate 20 mm nominal size) and curing complete, mixing the material in mechanical mixture and compacting the concrete with viberator complete excluding cost of form work and reinforcement for reinforced concrete work including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge. including carriage of materials upto all leads and lifts.

Providing and laying Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, fecia ,mouldings, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand) : 3 graded stone aggregate 20 mm nominal size).and curing complete, mixing the material in mechanical mixture and compacting the concrete with viberator complete excluding cost of form work and reinforcement for reinforced concrete work including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge. including carriage of materials upto all leads and lifts.

Providing and laying tor steel reinforcement for reinforced cement concrete work including ,bending binding,straightening and placing in position complete in all floor level/ heights including cost of binding wire complete including entire carriage of material within all leads and lifts and other incidentials as per the direction by the Engineer-in-charge .

Providing Brick work using common burnt clay building bricks in foundation and plinth in Cement Mortar 1:6 (1 Cement : 6 Sand) upto all height 1st Class Bricks including carriage of material within all leads and lifts.

Providing Brick work using common burnt clay building bricks in superstructure 1:6 (1cement:6sand) up to all height including carriage of material within all leads, lifts and heights. 1st class bricks.

Providing Half brick work using common burnt clay building bricks in super structure above plinth level upto floor all height using first class building bricks in cement mortar 1:4 (1cement : 4sand) including carriage of materials upto all leads and lifts and as per the direction of Engineer in charge.

Providing and fixing factory made uPVC door frame double rebate of required colour & shade of size 50mmx95mm with a wall thickness of 5mm made by jointing 3 Nos heat bent PVC sheet C chanel of 5mm PVC foam sheet of sizes 35x30x25mm and 40x35x40mm & 25mmx30mmx35mm for jointing using solvent cement. the two side C channels shall be reinforced with 19mmx19mm M.S. square tube of 19 gauge and all the three "C" channels shall be fixed to flat base of 5mm thick PVC sheet with salvent cement. the profile shall be mitred at corners and joined by inserting 4 nos 150mm long bracket of 15mmx15mm M.S. square tube to inner side. the 19mmx19mm M.S. square tubes the door frame shall be fixed to wall with 100mm long M.S. screws to wooden or rawl plugs embedded in masonry complete as per the specification of manufactures & direction of Engineer -in-charge including carriage of materials within all leads and lifts . .

Providing and fixing factory made uPVC door frame single rebate of any clours of size 50x47mm with a wall thickness of 5mm made out of extruded 5mm rigid PVC foam sheet heat bend & mitred at corners and jointed with 2 Nos. of 150mm long brackets of 15mmx15mm M.S. square tube, the vertical door profiles to be reinforced with 19mmx19mm M.S. square tube of 19 gauge EPDM rubber gasket weather seal to be provided throughout the frame i/c fixing of door frame to wall with M.S. screws 100long with wooden or rawl plugs emedded in masonry complete as per manufactures specification & direction of Engineer-in-Charge including carriage of materials within all leads and lifts . .

Providing and fixing to existing door frames, 30mm thick factory made uPVC panelled door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19mm x19mm for styles and 15mmx15mm for top & bottom rails, M.S. frame shall have a coat of steel primers of approved make and manufacture M.S. frame covered with 5mm thick heat moulded PVC "C" channel of size 30mm thickness, 70mm width out of which 50mm shall be flat and 20mm shall be tappred in 45 degree angle on either side forming style and 5mm thick, 95mm wide, PVC sheet out of which 75mm shall be flat and 20mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115mm wide PVC sheet out of which 75mm shall be flat and 20mm shall be tapered on both side to form lock rail, top, bottom and lock rail shall be provided either side of the panel 10mm thick, 20mm wide cross PVC sheet be provided as gap insert for top rail and bottom rail paneling of 5mm thick both side PVC Sheet to be fitted in the M.S. frame welded/sealed to the style & rails, joints mitred and jointed with solvent cement adhesive i/c fixing of PVC shutter with existing frame with M.S. butt hinges 100x50x1.90mm size with necessary screws zinc alloy (white powder coated) 3D hinges and one handle on each side of panels along with zinc plated mild steel multi point locking having transmission gear etc complete including carriage of materials within all leads and lifts . .

Providing and fixing to existing door frames 30mm thick factory made wire mesh solid PVC door shutters consisting of frame made out of M.S. tube of 19 gauge thickness of size 19mmx19mm for style and 15mmx15mm M.S. square tube for top, bottom & Lock rail M.S. frame shall have & coat of steel primer and covered with 5mm thick PVC solid sheet heat moulded "C" channel of size 75mmx30mmx60mm out of which 10mm shall be bent at 90degree towards inner side on front face of the door M.S. frame at lock rail shall be covered with 100mm wide PVC sheet out of which 10mm on both the edges shall be bent at 90 degree on front face of the door and 85mm wide PVC sheet shall cover the M.S. frame at top, bottom & lock rail lof 70mm on back side of door 5mm thick 20mm wide cross PVC sheet as gap insert for top and bottom rail, PVC sheet beading of 10mm thick, 15mm wide PVC sheet beading in to be stick internally in the back side of style and rails of door with solvent cement adhesive i/c fixing of G.I. wire mesh 85G or 0.56 dia wire fixed between PVC sheet of style and rail bent at 90 degree on front face using 15mmx15mm L-shape PVC beading nailed on style a rails i/c fixing shutter to existing door frame with M.S. butt hinges 100x58x1.90mm with necessary screws, zinc alloy (white powder coated) hinges and one handle on each side of panels along with zinc plated mild steel multi point locking having transmission gear etc. complete including carriage of materials within all leads and lifts.

Providing and fixing toughned glass glazing in upvc door, window, ventilator shutters and partition etc with PVC/neoprens gasket etc. complete as per the architectural drawings and the directions of Engineer-In_charge glazing with glass panes of 5.00 mm thickness (Weight not less than 13.75 kg/sqm.) including carriage of materials within all leads and lifts

Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately) Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm) including carriage of materials within all leads and lifts.

Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately) Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Two track two panels sliding window made of (small series) frame 52 x 44 mm & sash 32 x 60 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area of window upto 1.75 sqm) including carriage of materials within all leads and lifts.

Providing and fixing galvanised S.S. wire gauge of IS gauge designation 140 g with wire of dia 0.71 mm to windows and clerestory windows including beading of aluminium including carriage of material within all leads and lifts.

6mm (Six milimetre) cement plaster to ceiling in cement mortar 1:3 (One Cement is to three Sand) in all floor level. The rate isincluding carriage of materials within all leads and lifts and as per the direction of Engineer-in-Charge.

15mm (fifteen milimetres) thick cement plasters in single coat on rough/fair side of brick/concrete/stone walls for interior/exterior plastering upto all floor level including arises, internal rounded angles, chamfers and or rounded angles not exceeding 80mm (Eighty milimetres) in girth and finished even and smooth with cement mortar 1:6 (one cement: six sand) including carriage of materials within all leads and lifts and as per the direction of Engineer-in-Charge.

Rough side exterior cement plaster on wall upto all height with a mixture of sand and gravel or crushed stone graded from 6mm to 12mm nominal size dashed over and including fresh plaster in two coats,backing coat 10mm cement plaster 1:3(1 cement:3 sand)and finishing coat 10mm cement plaster with cement mortar 1:3(1 cement:3 sand)mixed with 10% finely grounded hyderated lime by volume of cement including arriss,chamfers and/or rounded angles not exceeding 80mm in girth. Natural cement finish using ordinary cement. including carriage of materials within all leads and lifts and as per the direction of Engineer-in-Charge.

Applying Birla white wall care putty two coats over plaster surface after thoroughly brushing the surface free from mortar drops, dust, loose materials and other foreign matters sand papered smooth to give final matter finish to the surface complete. including carriage of materials upto all leads and lifts.

Distempering (two coats) with oil bound washable distemper of approved brand and manufacture and of required shade on undecorated wall surfaces to give an even shade over and including a priming coat with distemper primer of approved brand and manufacture after thoroughly brushing the surface free from mortar droppings and other foreign matter and also including preparing the surface even and sand papered smooth. Priming coat with distemper primer including carriage of materials upto all leads and lifts.

Finishing wall with weather proof exterior grade emulsion of approved design (Apexultima) or its equarlied on undecorated wall surfaces (two coats) to give an even shade and final finish after throughly cleaning the surface to remove all dirt, dust and other foreign matter etc including sand paper smooth and cement primer complete. including carriage of materials upto all leads and lifts.

Painting two coats (including priming coat) on new steel and other metal surfaces with enamel paint brushing to give an even shade including cleaning the surfaces of all dirt, dust and other foreign matters:- With white enamel paint.or other than white including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge.

Providing and fixing double charge 10mm thick anti skid water proof stain and impect resistent heavy duty and Mat Finish vetrified tiles of approved make, in all colours, and any size as approved by Engineer-in-Charge manufactured of required shade and colour in flooring, treads of steps and landings laid with spacers laid over 12mm thick cement mortar 1:3 (1 cement : 3 sand) and jointed with grouting of Epoxy material mixed with pigment to match the shade of tiles in all storeys, height, levels and location as required complete.including carriage of materials upto all leads and lifts. SIZE 600X600mm

Providing and laying flamed finish Granite stone flooring and wall in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge : Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent. including carriage of materials upto all leads and lifts

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. including carriage of materials upto all leads and lifts.SIZE 600x1200mm

Providing and laying chequered tile 22mm thick laid on cement concrete 1:3 (1 Cement : 3 Sand) under layer for plinth protection (unconsolidated) bed dry brick/stone aggregated 40mm nominal size with rammed and consolidated and grouted with fine sand including preparation of ground including carriage of materials upto all leads and liftsSIZE 400x400mm

Steel work welded in built up sections,trusses and framed work,including cutting ,hoisting ,fixing in position and applying a priming coat of red lead paintIn gratings framed guard bars,ladders,railling,brackets , roof and similar works of using channels ,Tee,angles,circular, square,Tubular pipesof any size and rectangular hollow sections and including carriage of materials upto all leads and lifts.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.47 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.including carriage of materials within all leads and lifts and as per the direction of Engineer-in-Charge. Tata make

Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete :Ridges plain (500 - 600mm)

Providing and fixing of M.S. BP sheet 1.66mm to 2mm thick in eaves board/facia/soffits/ceiling including cutting, fixing and welding to steel roof members and applying a coat of red lead primer complete as per the instructions of the Engineer-in-charge. including carriage of materials upto all leads and lifts.

Providing and fixing on wall face PVC(D-Plast) rain water pipes of working pressure not less than 4.5 kg/sqm including filling the joints withapproved adhesive complete.110mm dia pipes including carriage of materials upto all leads and lifts

Providing and fixing accessories for wall face PVC(D-Plast) rain water pipes ie. bends, tee clamps etc. 110mm dia pipes including carriage of materials upto all leads and lifts

Constructing manhole with R.C.C top slab in 1:2:4 mix in 1 cement : 2 sand : 4 graded stone aggregate 20mm nominal size) foundation concrete1:4:8 (1cement : 4 sand : 8 graded stone aggregate 40mm nominal size) inside plastering 15mm thick with cement mortar 1:3 (1cement 3 sand) finished with a floating coat of neat cement and making channels in concrete 1:2:4 mix (1 cement : 2 sand : 4 graded stone aggregate 20mm nominal size) finished smooth complete including curing and testing: including carriage of materials upto all leads and lifts.Inside size 800mm x 800mm and 500mm deep including precast RCC manhole Cover and frame of required shape and approved quality HD 20 Circular shape 560 mm internal diameter ( heavy duty test load 20MT as per IS 12592 Part I & II ) With 230mm thick walls of brick masonry using common burnt clay building bricks in cement mortar 1:3 (1 cement : 3) including carriage of materials within all leads and lifts

Providing and fixing to wall ceilling and floor galvainised mild steeel tubes(medium grade)tube fittings and clamps including making good the wall including carriage of material within all leads and lifts. (A) 15 mm nominal bore. including carriage of materials upto all leads and lifts.

(B) 20 mm nominal bore. including carriage of materials upto all leads and lifts.

(C) 25 mm nominal bore. including carriage of materials upto all leads and lifts.

Making connection of galvainised steel distribution branch with galvainised mild steel main 15mm to 40mm nominal bore by providing and fixing Tee including cutting and threading the pipes complete including carriage of material within all leads and lifts.

Providing and fixing high pressure PVC 4.5 kg/sqm pressure spigot and socket, waste and ventilating pipes ISI marked including fixing with approved adhesive etc. complete 110 mm dia.including carriage of materials upto all leads and lifts.

Providing and fixing high pressure PVC 4.5 kg/sqm pressure spigot and socket, waste and ventilating pipes ISI marked including fixing with approved adhesive etc.150 mm dia including carriage of materials upto all leads and lifts.

Providing and fixing PVC accessiries ISI marked including fixing with approved adhesive etc. complete. Plain bend 110 mm nominal size. including carriage of materials upto all leads and lifts.

Providing and fixing PVC accessiries ISI marked including fixing with approved adhesive etc. complete.Door bend 110 mm nominal size. including carriage of materials upto all leads and lifts.

Providing and fixing PVC accessiries ISI marked including fixing with approved adhesive etc. complete.Plain Tee 110 mm nominal size. including carriage of materials upto all leads and lifts.

Providing and fixing pvc cowl 110mm dia including carriage of materials upto all leads and lifts.

Providing and fixing PVC floor trap ISI marked of self cleaning design including fixing with approved adhesive, cost of cutting and making good the wall and floors etc. complete. 110 mm X 90 mm including carriage of materials upto all leads and lifts.

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level PVC flushing cistern with GI inlet connections ,PVC connection pipe 30cm length ,seat and cover and zet and P or S trap including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required :W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing wash basin including with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm PVC waste of standard pattern,PVC connection pipe 30cm length , concealed and 15mm CP stop cock including painting of fittings and brackets, cutting and making good the walls wherever require:White Vitreous China Flat back wash basin size 550x 400 mm with single 15 mm C.P. brass pillar tap and stop cock including carriage of material within all leads and lifts.

Providing and fixing viterous china pedestal for wash basin complete recessed at the back for the recption of pipes and fittings including carriage of materials upto all leads and lifts.

Providing and fixing 100mm dia. Stainless steel grating for gully,foor or Nahani trap including carriage of material within all leads and lifts..

Providing and fixing 600x450mm bevelled edge mirror of superior glass mounted on 6 mm thick AC sheet or plywood sheet and fixed to wooden plugs with CP brass screw and washers including carriage of material within all leads and lifts.

Providing and fixing CP brass towel rail complete with CP brass brackets fixed to wooden pluges with CP brass screws 600x20mm including carriage of material within all leads and lifts.

Providing and fixing CP brass bib tap with capastan head 15 mm dia. including carriage of material within all leads and lifts.

Providing and fixing CP stop cock 15mm dia including carriage of material within all leads and lifts.

Providing and fixing brass full way valve with wheel 15mm nominal bore including carriage of materials upto all leads and lifts.

Providing and fixing brass full way valve with wheel 20mm nominal bore including carriage of materials upto all leads and lifts.

Providing and fixing brass full way valve with wheel 25mm nominal bore including carriage of materials upto all leads and lifts.

Providing and fixing GI or MI union15mm nominal size including carriage of materials upto all leads and lifts.

Providing and fixing GI or MI union20mm Nominal size including carriage of materials upto all leads and lifts.

Providing and fixing GI or MI union25mm Nominal size including carriage of materials upto all leads and lifts.

Providing and fixing charomium plated brass soap dish with C.P.brass brackets fixed to wooden cleats with C.P. brass screws including carriage of material within all leads and lifts.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.including necessary fittings including carriage of material within all leads and lifts.

Providing and fixing white glazed fire clay squatting plate pattern single stall urinal of 600mmx500mm size of Cera/ Pariware Make including carriage of material within all leads and lifts.

Providing and fixing Division Plate for Urinals 600mm x 300. Vitreous China including carriage of materials upto all leads and lifts.

Excavation in earth work and banking in 20 cm. layers including breaking clods, ramming and dressing ground for the purpose of making embankment or filling up ground depressions upto al lead and lift including carriage of materials upto all leads and lifts.

Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in Charge80mm thick inter locking blocks sqm including carriage of materials upto all leads and lifts.

Cement concrete flooring 1:2:4 (1 cement : 2 sand:4 graded stone aggregate 20 mm nominal size)laid in one layer finished with a floating coat of neat Cement. 50mm thick. including carriage of materials upto all leads and lifts.

Rajat Kumar (BID ID -519331)

Karnail Singh (BID ID -519241)

Sohan Singh Govt. Contractor (BID ID -519498)