ADDN/ALTN CUM SPECIAL REPAIRS OF OFFRS, JCOS/OR AND CIV MD ACCN UNDER GE (EAST) LUCKNOW

Amount

Taking down cement plaster or cement lime plaster on PCC/stone surface/brick surfaces including raking out joints hacking for key scrubbing down with water etc complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floor and paving n.exc 15 cm thickness below and above ground level, complete all as specified and directed.

Demolition of Brickwork or stone/boulder masonry, built in cement mortar or cement lime mortar mortar including all quoins, arches, pillars,etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed.

M & L for old size brick work using fly ash brick straight or curved on plan, exc 6.0 m mean radius, built in CM (1:6) , complete all as specified and directed.

M & L for old size brick work with fly ash bricks straight or curved on plan to any radius in half brick thick walls, in CM 1:4, complete, all as specified and directed.

dismantling brick tiles or terracing tiles,mud phuska including concrete/ cement screed bed in any depth of roof complete all as specified and directed

Striping out old roof treatment (tarfelt) from roof top and removing from site complete all as specified and directed.

M&L PCC 1:2:4, type B1 using 20 mm graded stone aggregate using WPC @3% by weight of cement as in roof kerbs / benching / coving and roof padding over roof surfaces /sunken treatment etc rounded or chamfered on edges, complete, all as specified and directed. Note:- The water proofing compound measured & paid separately relevant Item

M&L for rendering 15 mm thick in cement mortar 1:6 on fair face of brick work of walls, finished even & smooth without using extra cement, complete all as specified and directed.

M&L for rendering 15 mm thick in cement mortar 1:4 on fair face of brick work of walls, mixed with water proofing compound (ISI marked) @ 2% by weight of cement or as per manufacturer’s instructions, finished even & smooth without using extra cement complete all as specified. incl mouldings, chamfers, splay srounded or coved angles, beads,grooves and rebate upto 10 cm in width or 15 cm in girth complete, all as specified and directed.. Note : - Water proofing compound shall be measured and paid for separately.

M&L for rendering 5 mm thick in cement mortar 1:3 on concrete surfaces in ceiling, finished even & smooth without using extra cement, complete, all as specified and directed.

Supply only integral water proofing compound, ISI Marked.

M&L for preparation of new plastered surfaces of walls and applying two coats of of oil bound distemper over 1mm thick wall care putty and one coat of alkali resistant primer and including necessary scaffoldings as required etc complete all as specified and as directed.

Material and labour for complete removal of existing surface including washing / rubbing down with water of wall and applying two coats of oil bound distemper over coat of alkali resistant primer including two coat of birla wall care putty to make the surface smooth and including necessary scaffoldings as required etc complete all as specified and as directed.

M&L for preparation of newly plastered surfaces of wall & applying two coats of cement base paint of approved shade/tint over a coat of water based cement primer and including necessary scaffoldings as required etc complete all as specified and as directed. Note:-Necessary curing shall be carried out during execution of work as per standard engineer practice

M&L for complete removal of existing teatment from old plastered surfaces of wall & applying two coats of cement base paint of approved shade/tint over a coat of water based cement primer and including necessary scaffoldings as required etc complete all as specified and as directed. Note:-Necessary curing shall be carried out during execution of work as per standard engineer practice

M&L for preparation of newly plastered surfaces of ceiling & applying three coats of white wash, complete, all as specified and directed.

M&L for complete removal of old decorated plastered surfaces of ceilling and applying two coat of white washing on ceilling after preperation of undecorated surface complete, all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), and rubbish off the premises complete, all as specified and directed.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc. complete, all as specified and directed.

M& L for Vitrified tile double charged 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar 1:6, complete all as specified and as directed.

All as per above item No. 25 but on vertical surfaces over and including 10mm thick screed plaser in CM 1:4 , complete all as specified and as directed.

M&L for non skid ceramic joint free tiles (coloured) 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.09 sqm but not exceeding 0.18 sqm as in floors , set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar 1:6, complete all as specified and as directed

All as per above item No-27 but on vertical surfaces including 10mm thick rendering in CM 1:4 , complete all as specified and as directed.

M&L for ceramic, joint free tiles (coloured) 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar 1:6, complete all as specified and as directed.

All as per item No 29 above but on vertical surfaces over and including 10mm thick rendering in CM 1:4 , complete all as specified and as directed.

M&L for glazed ceramic tiles (coloured) 300x600 x 7mm thick on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10 mm thick rendering (as screed bed) in cement & sand mortar 1:4, complete all as specified and as directed.

M&L machine cut Kota stone slab flooring 20-25mm thick over and including 15mm screed bed (1:6) laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and including granite polish on Kota slab stone a complete all as specified and directed.

All as per item No 32 above but on vertical surface such as dado, skirting etc over and including 10 mm thick rendering in CM 1:4 complete all as specified and directed.

M&L for 75 mm thick PCC 1:3:6 type C2 using 40 mm graded crushed stone aggregate as in plinth protection surface finished fair and even without using etra cement complete all as specified. Note :- Plinth protection shall be of width as directed and shall be laid to slope of 1:30 in alternative bays not exceeding 3 meter in length. Joints of 6 mm wide and 10 mm deep shall be provided along the wall and bays and same shall be filled with bitumen mastic (1:3) complete all as specified and directed.

M&L Granite 18-20mm thick (of any type of minimum 2 m length of piece) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over and including 20mm thick screed in CM 1:4 including cutting, polishing, rubbing & moulding of edges including demolition of stone slab complete, all as specified and directed.

Rounding to edges of stone slabs one edge, such as in steps, cooking plateform and other similar situation complete, all as specified and directed.

Demolition of sunken slab floor of WC and Bath including WC trap etc incl taking down loose filling of aggregate in any type and removing where direted and providing water proofing treatment of sunken slab as follows:- (a) 15mm thick rendering on vertical sides of RCC slab in CM 1:3 mixed with chemical " PIDIPROFF LW of Dr Pidilite or equivalent " as per manufacturer instructions. (b) Cleaning the concrete surface by brushing and watering and remove all surface inperfections. (c) Fixing 40mm dia Pipe 450mm long at bottom of the sunken floor and wraping of bath seal tape on the pipes inserted through walls to floor area and seal it (Bath seal tape product of Dr fixit or equivalent and grouting around the inserted pipes by pouring Dr fixit bath seal or equivalent grout as directed (d) Make angle fillets by mixing sand cement and Dr fixit pidicrete URP or equivalenont all corners. (e) Brushing neat cement slurry two coats with high performance cementitious polymer water proofing coating of Dr fixit bath seal WPC or equivalent of thickness 1mm in combination of WPC and cement (1:1.5) by vol and giving upto height 15cm from bottom slab and allow it dry completely. (f) Providing PCC 1:4:8 type D-2 using 40mm graded stone aggregate mixed with WPC as per mnufacturer instructions in sunken slab over brick bat . (g) Fill the sanitary gaps with sealing compounds complete.

Taking up or down steel water tubing and connections of 15mm bore, fixed in walls, ceiling, floors, trenches etc. complete all as specified and directed.

Taking up or down steel water tubing and connections of 20mm bore, fixed in walls, ceiling, floors, trenches etc. complete all as specified and directed.

M&L for cutting chases, pinning in, making good to facings as original where required and pointing in cement mortar 1:3 for concealed water tubing etc. and making good, cutting not exc 10 cm girth in brick walls complete all as specified and directed.

M&L for galvanized steel water tubing medium grade of 15mm bore with & including all GI fittings (ISI Marked) and fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

M&L for galvanized steel water tubing medium grade of 20mm bore with & including all GI fittings (ISI Marked) and fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

M&L for galvanized steel water tubing medium grade of 25mm bore with & including all GI fittings (ISI Marked) and fixed complete to walls and ceilings or laid in floors including aking up or down steel water tubing and connections of 20mm bore, fixed in walls, ceiling, floors, complete all as specified and directed.

S&F in repair Vitreous China wash down water closet pan (pedestal pattern), white including fixing bolts, seat cover , (excluding flush pipe) and 'P' or 'S' trap, including connection to trap and flushing pipe, antisyphonage pipe etc including provision of PCC (1:5:10) type E2 usi in filling, making good to floor, complete all as specified and directed.

S&F in repair vitrious China squatting pan orissa pattern size 580x440mm white with integral foot rest (excluding flushing cistern & flush pipe) including connection to trap set and to flush pipes etc and lime concrete bedding complete all as specified and directed.

S&F in repair PVC valveless symphonic action type low level flushing cistern (ISI marked) of 10 litre capacity including 32 mm dia PVC flush pipe connected to water closet with inlet, ball valve, float and handle complete all as specified and directed.

S&F in repair vitreous china wash hand basin, white, flat back of size 550mm x 400mm with & including a pair of cast iron brackets embedded in PCC 1:3:6 type C1 blocks of size 10x7.5x15cm, 32 mm dia PVC waste pipe and 32mm bore chromium plated brass waste fitting with long screwed shanks and fly nuts, flange end bedded in red lead cement & other end fixed, (excluding tap, waste chain & plug), complete all as specified and directed.

S&F in repair sink with drainage board made of stainless steel 1mm thick for kitchen with plugs, washers and wastes, including fixing with cast iron cantilever brackets, bedding in cement mortar on to dwarf wall, connecting union to pipe, overall minimum size 915mm x 460 mm with bowl size 410mm x 330mm x160 mm including 32mm dia waste pipe of polythelene of low or high density, 32mm bore chromium plated brass waste fitting with long screwed shanks and fly nuts, flange end bedded in red lead cement & other end fixed, making holes in walls for brackets and fixed in CM 1:3 or PCC 1:2:4 type B0, complete, including taking down old unserviceable sink incl 40mm dia Waste coupling of PTMT (half or full threaded) complete all as specified and directed.

S&F in repair sinks made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160m including 32mm dia waste pipe of polythelene of low or high density, 32mm bore chromium plated brass waste fitting with long screwed shanks and fly nuts, flange end bedded in red lead cement & other end fixed, making holes in walls for brackets and fixed in CM 1:3 or PCC 1:2:4 type B0, complete, including taking down old unserviceable sink incl 40mm dia Waste coupling of PTMT (half or full threaded) complete all as specified and directed.

S&F in repair 15mm bore Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed long body for kitchen sink complete all as specified and directed.

S & F stainless steel Kitchen plate rack of overall minimum size 750 mm x 600 mm and 250 mm deep, with partitions for small/large plates etc made out of stainless steel 0.80 mm thick fixed with rawl plug and CP steel screws complete all as specified and directed.

S & F in repair stainless steel Kitchen plate rack of overall minimum size 750 mm x 900 mm and 250 mm deep, with partitions for small/large plates etc made out of stainless steel 0.80 mm thick fixed with rawl plug and CP steel screws complete all as specified and directed.

S&F in repair CP Brass square gratings 125mm dia with waste hole (Minimium weight 40 grams) complete all as specified and directed.

S&F in repair PTMT grating 125mm dia without waste hole (Minimium weight 40 grams) complete all as specified and directed.

S&F in repair PVC connection 450 mm long suitable for 15 mm bore GI pipe including CP brass nuts on both sides, complete all as specified and directed.

S&F in repair long body 15mm bore fancy type bib tap of min weight 0.575 kg, cast copper alloy, chromium plated with capstan head, screwed down, screwed for iron pipe or for brass ferrule, complete all as specified & directed.

S&F in repair cp angle valve fancy type of min weight 0.575 kg, long body for 15 mm bore pipe with capstan head long screwed shank including cp cover plate fancy type complete all as specified and directed.

S&F 15 mm bore CP brass Central Hole Basin mixture fixed to GI pipe complete all as specified and directed.

S & F in repair single lever brass CP wall mixer 3-in-1 system with provision for over head shower with 115 mm long bend pipe, connecting legs and wall flange (without overhead shower) shower for iron pipe of 15 mm bore GI pipe complete all as specified and directed.

S&F in repair hand shower (Health faucet) with 1 Mtr flexible tube with wall hook bracket etc, complete set of superior quality complete all as specified and directed.

S&F in repair toilet paper holder CP fixed complete all as specified and directed .

S&F glass corner self assembly, fancy type, made of 6 to 7mm thick sheet toughened glass of size 250x250mm, fixed with CP brackets, complete all as specified and directed. Make: Jaquar range OR equivalent

Supply & fix sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed.

S&F in repair CP brass tubular towel rail, 20mm dia, ‘D’ type, 60cm long between flanges, fixed to PVC rawl plugs with chromium plated brass screws, ccomplete all as specified and directed.

S&F in repair 40mm bore PVC low density (LDPE) pipe of pressure 6kg/Cm2 fixed to wall or laid in floor, ccomplete all as specified and directed.

S&F in repair brass chromium plated shower rose 125 mm size without swivel joint including fixing to steel pipe of 15mm bore or union complete all as specified and directed.

S&F in repair pvc(swr) 125 mm bore floor/nahani trap including jointing with solvent cement complete all as specified and directed

Disconnecting existing tanks, exc 250 Ltr & n.exc 500 Ltr setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position.(Cleaning repairing, etc. measured separately) complete all as specified & as directed.

Disconnecting existing tanks, exc 500 Ltr & n.exc 1000 Ltr setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position.(Cleaning repairing, etc. measured separately) complete all as specified & as directed.

Dismantling PVC water tanks and removing for capacity exceeding 250 litres & not exceeding 500 litres etc., all as directed.

S&F rotational moulded polyethylene water storage tank of capacity 500 Litre, three layer construction, white colour, ISI mark (cylindrical vertical with closed top) hoisted and fixed in position with and including 20 mm dia GI pipe medium grade washout pipe 450 mm long with plug and 20 mm dia GI pipe medium grade overflow pipe 600 mm long with fittings complete all as specified and as directed.

Dismantling PVC water tanks and removing for capacity exceeding 500 litres & not exceeding 1000 litres etc., all as directed.

S&F rotational moulded polyethylene water storage tank of capacity 1000 Litre, three layer construction, white colour, ISI mark (cylindrical vertical with closed top) hoisted and fixed in position with and including 20 mm dia GI pipe medium grade washout pipe 450 mm long with plug and 20 mm dia GI pipe medium grade overflow pipe 600 mm long with fittings complete all as specified and as directed.

S&F in repair 20 mm ball valve high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe, complete all as specified and directed.

S&F in repair gun metal globe or gate valve with iron wheel head, screwed both ends for iron pipe and fixed of 20 mm bore, complete all as specified and directed.

Supply & Fixing gun metal gate valve screwed both ends to 15mm bore pipe complete all as specified and directed.

S&F PVC coated 25mm dia anodize aluminium alloy pipe as in curtain rods including brackets and fancy type end knobs, complete, complete all as specified and directed.

S&F in repair stainless steel 25 dia pipe as in curtain rods incl SS brackets and fancy type end knobs, complete all as specified and directed.

Demolition and breaking up or taking down PVC/AC/CI/SSW 100mm/75mm bore pipe drain pipes, set in cement mortar including PCC haunching and bedding, complete all as specified and directed.

S&F 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall including PVC holding clamps, complete all as specified and directed.

S&F 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall including PVC holding clamps, complete all as specified and directed.

S&F 110mm bore PVC (SWR) bend, any radius complete all as specified and directed.

S&F 75mm bore PVC (SWR) bend, any radius with access door. complete all as specified and directed.

S&F 75mm bore PVC (SWR) bend, any radius complete all as specified and directed.

S&F 110mm bore PVC (SWR) vent cowl complete all as specified and directed.

S&F PVC(SWR) 110mm dia branch piece, single(single Y) equal or enequal with access door complete all as specified and directed.

S&F PVC(SWR) 75mm dia branch piece, single(single Y) equal or enequal with access door complete all as specified and directed.

Taking down chowkhat with shutter (without taking off shutter from the frame) and area exc 1.5 sqm but n.exc 4 sqm each, complete all as specified and directed.

Taking down chowkhat with shutter (without taking off shutter from the frame) and area not exc 1.5 sqm each, complete all as specified and directed.

M&L plain cement concrete cast in situ 1:3:6 type C1 using 20 mm graded stone aggregate as in copings ,hold fast,back filling of pressed steel frame and other similar work water troughs and the like including weathering, slightly rounded or chamfered angles and throating etc including form work complete all as specified and directed.

S&F pressed steel frame for door with one or more rebates size 125x60mm including necessary fixing lugs, lock striking plates,hinges,hold fast etc. complete size /profile of frame as per IS complete all as specified and directed.

S&F pressed steel frame for door with one or more rebates size 105x60mm including necessary fixing lugs, lock striking plates,hinges,hold fast ,etc. complete size /profile of frame as per IS complete all as specified and directed.

M&L 35mm thick factory made door shutter plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed.Note:-Shutter shall be manufactured as per TD No LZ/C-TD/125 sheet No 1/3 to 3/3

Supply and fixing factory made 35mm thick glazed and skeleton shutters made of second class hard wood, open rebated and prepared to receive glass, gauze etc (with sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc., sizes of members of shutters as specified in clause 8.24 (a) of Section 8 in SSR Part-I, kiln seasoned and chemically pressure treated, fixed to chowkat, complete all as specified & directed.Note:-Shutter shall be manufactured as per TD No LZ/C-TD/125 sheet No 1/3 to 3/3

S&F Solid PVC frame (Single Rebated) of size 60mm x 30mm made out of solid PVC foam with homogenous fine cellular structure having smooth outer integral skin with suitable metal stiffner and fixed with 100 x 8 sheet metal CSK screws complete all as specified and directed. (Note :- Door frame shall be water proof, termite proof, elegant and should have excellent screws holding strength to fix hinges and hold doors properly for a long life)

S&F Factory made soild PVC profiled panel door shutter 28mm thick with integral skin as frame & 3mm thick high pressure compact laminate on both side of approved colour as infill, with 'C type Gl or 40 x 20 x19 of MS pipe as stiffner complete all as specified and directed.

S&F butt hinges of size 100 mm medium weight, stainless steel ISI marked ccomplete all as specified and directed.

S&F aluminium handle fancy type, 150mm size, cast type, anodized (ISI marked) complete all as specified and directed.

S&F 200 mm long aluminium anodized barrel tower bolts fancy type of extruded section (ISI marked) complete all as specified and directed.

&F 300 mm aluminium alloy, anodised, sliding door bolt fancy type with hasp, staple (bolt type) and fixing clips of sheets, cast or extracted sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed complete all as specified and directed.

S&F mild steel helical door spring 300mm ordinary rat tail rod pattern spring including roller and roller plate complete all as specified and directed.

S&F 150mm Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed.

S&F Eye door viewer (Magic Eye) of suitable size fixed with panneled door shutter complete all as specified and directed.

S&F in repair 300mm long stainless steel six peg hanger of minimum weight 150gms chromium plated as approved by engr-in-charge complete all as specified and directed

S&F mild steel Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165 including welding work complete all as specified & as directed. Note:Design and pattern of window Grills as decided by GE at site.

S&F stainless steel grade 304 Framed work such as staircase raling etc.. with ends of bars shouldered and/or riveted, or forged into spikes walk ways; railings including welding work complete all as specified & as directed. Note:-Railing shall be manufactured as per TD No LZ/C-TD/109 sheet No 1/1

M & L Prepainted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour approved by GE having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws all as specified & directed.

M&L for mild steel work as in roof trusses (framed) purlin, and heavy bracket framing(beam, tee,angle,channel or flat sections) including distance pieces, cleats etc complete all as specified and directed.

S&F stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire, staples complete all as specified and directed.

All per item No 110 above but fixed in repairs.

M&L for preparation of new surfaces of wood or wood based materials of any description over 10 cm width or girth and applying two coats of synthetic enamel paint of approved tint over a coat of pink primer complete all as specified and directed.

M&L for preparation of new surfaces of steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint of approved tint over a coat of red oxide complete all as specified and directed.

M&L for preparation of old painted surfaces of wood and wood based material of any description over 10 cm in width or girth and applying one coat of synthetic enamel paint of approved tint complete all as specified and directed.

M&L for preparation of old painted steel and iron surfaces of any description over 10 cm in width or girth and applying one coat of synthetic enamel paint of approved tint complete all as specified and directed.

S&F magnetic catcher with strike plate of brass body for cup board shutters complete all as specified and directed.

s&f stainless steel handle, 150mm size with smooth finish matching the requirment of relevant is code as approved by engr-in-charge complete all as specified and directed.

S & F auto concealed hinges SS size 103mmx64mmx28mm suitable for cabinet and wardrobe complete all as specified and directed.

Demolition of reinforced cement concrete in floors ,beams ,chajjas,landing slab in any position or height and similar suspended works complete all as specified and directed.

M/L RCC 1:11/2:3 type A1 (using 20 mm graded aggrigate)as in slab, chajjas, beam etc complete all as specified and directed.

Use and waste of Form work to soffits of suspended slab such as roof slab, floor slab, landing and similar work n.exc 200mm thick complete all as specified and directed.

M&L 10mm dia and over TMT bars, cut to length, bent ot shape required, including cranking, bending , hooking ends and binding with and including mild steel wire(annealed not less than 0.9mm dia) icluding welding, rivetting etc complete all as specified and directed.

Repairing of RCC projections chajjas, roofs, facia etc by necessary preparation, scrapping, cutting, chiseling, derusting and cleaning exposed reinforcement, surfaces of damaged, loose RCC and providing cement concrete (1:1.5:3) using 12.5 mm graded crushed stone aggregate including necessary form work and reinforced with chicken wire mesh and rendering in cement mortar 1:3 using coarse sand in patches area not exceeding 5 sqm each and thickness of RCC member not exceeding 150mm including applying two coats of finishes as provided to the existing surfaces to match with the existing surfaces in at any height complete all as specified and directed.

M&L providing and injecting chemical emulsion Post Constructional Antitermite Treatment along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear meter including drilling and plugging holes etc. in apron complete all as specified and directed.

M&L treating of soil under existing floors using emulsion Post ConstructionalAntitermite Treatment @ one litre per hole,300mm apart including drilling and plugging 12mm dia holes with cement morter 1:2 (1 cement :2 coarse sand) to match the existing floor complete all as specified and directed.

S&F stainless steel security latches of suitable size with security chain , and fixed to in-side door with security bolt complete all as specified and directed.

S & F Plain mild steel wire 4mm dia, galvanised class 3,in cloth hanger including straining and fixing to wood, concrete or steel posts and/or to straining bolts, including securing with and provision of galvanised iron tying wire, galvanised iron staples or steel pins, etc.complete all as specified and directed. (Note : Each line of wire to be measured)

Dismantling wrought iron mild steel wk of any description not otherwise provided for etc complete all as specified and directed.

M&L for mild steel framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified and directed.

S&F 1.00 MM thick Mild steel, plain black sheet in wall cladding,steel gates and similar work, cut to size, holes punched; including round headed screws,clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred as in garage gates and ventilators chhaja's complete all as specified and directed.

M&L for Mild steel TMT bars 08 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

S&F IInd class HW plain,solid,straight chowkhats and framed wrought,framed rebated,on the solid rounded or completed but together with gue pinned complete all as specified & directed.

Demolition of cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed.

M & L preparation and applying three coats of white wash on new plastered surface of wall complete all as specified and directed.

Supply and fixed in repair stop valves, 15mm dia, cast copper alloy,CP fancy type with long shank and cup(concealed type) screwd down,high pressure with crutch or butter fly handle,screwed both ends for iron pipes or for unions and fixed in pipe complete all as specified and directed.

S & F in repair CP pillar tap cast copper alloy of min weight 656 gms , with capstan heads, chromium plated, screwed down, high pressure fancy type with long shanks and fly nuts, screwed for iron pipe 15mm bore complete all as specified and directed.

Taking down shutters of any description exc 1 Sqm and n exc 2.0 sqm each and and removing to store etc complete all as specified and directed.

Taking down shutters of any description exc 1 Sqm and n exc 2.0 sqm each and refixing in same opening etc complete all as specified and directed.

M&L for 30 mm thick factory made flush shutters, solid core construction, with block board 3 core and plywood face panels, commercial type on both sides complete all as specified and directed.

S&F in repair 32 mm dia of discharge pipe bottel trap of PTMT having minimum water seal of 25 mm .(Minimum weight 32 mm -260 gms) etc complete all as specified and directed.

S&F in repairs long body 15mm bore two-way bib tap, cast copper alloy, chromium plated with capstan head, screwed down, screwed for iron pipe or for brass ferrule, complete all as specified & directed.

M&L providing cement concrete louveres and jallies, 25 mm thick (measured solid), inclunding all mouldings set in cement motar 1:4 type B0, 1:2:4 (using 12.5 mm graded stone aggregate) etc complete all as specified and directed.

S&F powder coated (min thickness of powder coating 50 micron) anodised aluminum window shutter three track sliding type, section having frame size bottom with outer 92x45.5x1.5mm (section code 20617) , top and side 92x31.75x1.5 (section code 20831) & aluminum section of shutter top and bottom size 40 x 18 x 1.5 ( section code 20736) , interlock size 40 x 18x 1.45 (section code 20737), side/ middle size 40 x18 x1.55, (section code 20738) including necessary joining cleats, glazing clips rubber backing, anodised aluminum snap beading screw, anodised aluminum fitting complete as per site requirtement glazing by using 5mm thick plain sheet glass and ss wiremess of dia 0.36mm and aperture 1.4mm thick all as specified and directed. ref drg no celz/c-td/151 sheet no 1/1 & 2/2 . NOTE- 1. Glazed shutter glass thickness not less than 5mm and SS wiremess shutter with ss wiremesh as approved by GE is also included. no payment will be made separately. 2. No extra payment will be made for section profilesprovided of higher sizes.

S&F powder coated (minimum thickness of powder coating 50micron)aluminum ventilator (louvers) with 3.8 mm thick plain / tinted glass consisting of frame of size 63.5 x 44 and sections weighing not less than 0.55 kg/m with locking arrangement as approved fixed including necessary joining cleats, glazing clips, rubber packing, powder coated aluminium snap beading, screws, powder coated aluminium fittings with stainless steel wiremesh of 0.36mm including necessary fixing arrangement complete all as specified and directed.

S&F 110mm bore PVC(SWR) pipes single socketed, any length with rubber ring joints laid in trenches or in floors complete all as specified and directed.

S&F PVC cabinet shutter as in Kitchen, Cup board, wardrobe etc with frame of min size 60mm x 44mm including shelves in required sizes at site made out of 18 mm thick one side decorative lamination & other side balancing lamination sheet & provision of shutter made out of 18 mm thick one side decorative laminated PVC sheet all required brackets stainless steel screw etc the panels shell be fabricated using adhesive and screws where ever required. All the edges shall be covered with 2mm thick edge bonding tape or 90 degree edge bend finish including all necessary fitting as per site requirement and as per make and specification mentioned complete all as specified and directed. Note:- Density of PVC solid sheet should not be less than 575 kg/M3

Demolition of stone slab and tiles of any description or thickness in floors, apron, etc laid bedded and pointed in any mortor etc complete all as specified and directed.

M&L for rendering 15 mm thick in cement mortar 1:4 on fair face of brick work or concrete surfaces of walls, finished even & smooth without using extra cement including mouldings, chamfers, splay srounded or coved angles, beads complete all as specified and directed.

M&L Hard core of Broken stone Boulders of gauge n.exc 63mm deposited spread & levelled in layers n exc 15cm watered and rammed to a true surface thickness all as directed

M&L plain cement concrete type D2 1:4:8 (using 40mm graded stone aggregate)as in sub base /mass concrete complete all as spciified and directed

M&L for Machine pressed precast concrete interlocking paver block rubber moulded any shape and size conforming to IS 15658-2006 of 60mm thickness,M-35 grade of approved design /colour set and bedded over sand cushion all as specified and directed.Note : Sand Cushion shall be measured and paid seperately

M&L factory made precast cement conc type B-1 , 1:2:4(using 20mm graded aggregate), as in kerb stones etc and set in CM (1:4) complete as directed and specified.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft/loose soil complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in soft/loose soil complete all as specified and directed

Removing excavated material (Soils) n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and directed

M&L 50 mm thick sand cushion and joint filled with fine sand including leveling tamping & sweeping etc all as specified & directed.

M & L for Plain Cement concrete Type B1 1:2:4 (20 mm graded stone aggregate) as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, complete all as specified and directed.

M & L for Plain Cement concrete Type C1 1:3:6 (20 mm graded stone aggregate) as in surface channels and drains complete all as specified and directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using ex- tra cement, including forms, moulds, mi- tred/stopped ends etc. complete all as specified and directed.

Add or deduct for each 25 mm girth or part thereof over or under 30cm for forming fair finish drain or channel in cement concrete using extra cement including forms, moulds, mitred, stopped ends, complete all as specified and directed.

M & L for Providing precast cement concrete ( 1:2:4) Type B1 ( using 20 mm graded stone aggregate) as cover slabs (for man holes etc.) set in CM 1:4 and similar articles with plain faces complete all as specified and directed.

S&F Reinforced concrete pipes 300 mm dia, class NP2, laid and jointed complete with collars complete all as specified and directed.

Demolition and breaking up drain pipe of any description up to 150mm dia in set CM 1:4 including demolition of cement concrete bedding and hunching complete all as specified and directed.

Demolition and breaking up drain pipe of any description exc 150mm dia and up to 200mm dia set in CM 1:4 including demolition of cement concrete bedding and hunching complete all as specified and directed.

Demolition of RCC of any description and in any position not other wise specially provided for reinforcement cut as required to facilitate demolition complete all as specified and directed.

Excavation in trenches exc 1.5 m wide and depth exc 1.5m but n.exc 3 m for foundation and getting out in soft/loose soil complete all as specified and directed.

M&L for PCC 1:3:6 type C-2 using 40mm graded stone aggregate as in concrete bed to drain pipe including packing under, and haunching against the sides of pipes after they are laid and tested for 150mm dia pipe complete all as specified and directed.

M&L for PCC 1:3:6 type C-2 using 40mm graded stone aggregate as in concrete bed to drain pipe including packing under, and hunching against the sides of pipes after they are laid and tested for 200mm dia pipe complete all as specified and directed.

M&L for 150mm bore PVC pipe type‘B’ matching the requirement of IS 13592 ,laid in trenches and jointed with sealent and testing of lines etc complete all as specified and directed.

All as per item No 170 above but 200mm bore pipe.

Cutting in to existing manholes for connecting new drains, making good to pipe & rendering, cutting out existing benching for and forming branch channel in cement concrete1:2:4 type B-1 smooth finished and reforming benching as required for 150 mm bore drain pipe complete all as specified and directed.

M&L for salt glazed stone ware gully traps size 150 x 150mm, square, type ‘P’ including setting and jointing to drains with CM 1:1 and CI grating including demolition of existing traps complete all as specified and directed.

S&F reinforced concrete pipes, class NP-2, laid and jointed complete with collars of 200mm dia as in repair complete all as specified and directed.

Cutting of bituminous road to the width and depth required for laying SWG pipe or sewage line including hacking , benching and including making good to top surface of road with bitumen & aggregate as per road specification complete and as directed.

M&L brick work with fly ash brick straight or curved on plan exc 6 m mean radius built in CM 1:4 complete all as specified and directed.

M&L for cement concrete 1:2:4, type B-1, using 20mm graded stone aggregate as in benching , surface channel and similar articles finishing even and smooth using extra cement complete all as specified and directed.

M&L for rendering 15mm thick in CM 1:4 on brick or concrete surface, finishing even and smooth using extra cement complete all as specified and directed.

S&F RCC Septic tank designed to carry sewage and sullage water, for 50 users excavation in any type of soil, PCC 1:4:8 below foundation, RCC M-30 Design Mix in Walls , Base Slab , Baffle walls and Roof Slab including beams etc with Vent shaft , manhole openings with cover connection etc., complete with effective depth of 1.5 meter and overall depth of 3 meter. complete all as shown in TD drg No TD 576 sheet 1/2 and 2/2 and TD 217 sheet 1/2 and 2/2 , specified and directed.

All as per item no. 179 above of Septic tank (3.00m overall depth) but overall depth exceeding beyond 3.00m and upto 4.50 m complete all as directed and specified. Note:- The tenderer shall quote rates for per meter of depth beyond 3.00m and upto4.50m. Actual payment shall be made based on actual depth provided at site for one meter depth or part thereof . Tenderer should note this aspect while quoting rates against this item.

All as per item no. 179 above of Septic tank (3.00m overall depth) but overall depth exceeding beyond 4.50m and upto 6.00 m complete all as directed and specified. Note:- The tenderer shall quote rates for per meter of depth beyond 4.50m and upto 6.00m. Actual payment shall be made based on actual depth provided at site for one meter depth or part thereof . Tenderer should note this aspect while quoting rates against this item.

S&F Soakage wells excavation, in any type of soil, foundation in PCC 1:3:6, walls of honey combed masonry with top ring of M25 concrete including intercepting chamber and screen chamber made of Brick masonary in CM, RCC cover slab in M25/ SFRC cover, interconnecting pipes of RCC/DWC complete filled with brick bats of size 2.4m dia and 4.5m effective depth complete all as shown in TD drg No TD 576 sheet 1/2 and 2/2 and TD 217 sheet 1/2 and 2/2 , specified and directed.

All as per item no. 182 above of Soakage well (4.5m effective depth) but depth exceeding beyond 4.50m and upto 6.00 m complete all as directed and specified. Note:- The tenderer shall quote rates for per meter of depth beyond 4.50m and upto 6.00m. Actual payment shall be made based on actual depth provided at site for one meter depth or part thereof . Tenderer should note this aspect while quoting rates against this item.

All as per item no. 182 above of Soakage well (4.5m effective depth) but depth exceeding beyond 6.00m and upto 7.50 m complete all as directed and specified. Note:- The tenderer shall quote rates for per meter of depth beyond 6.00m and upto 7.50m. Actual payment shall be made based on actual depth provided at site for one meter depth or part thereof . Tenderer should note this aspect while quoting rates against this item.

S&F RCC Septic tank designed to carry sewage and sullage water, for 100 users excavation in any type of soil, PCC 1:4:8 below foundation, RCC M-30 Design Mix in Walls , Base Slab , Baffle walls and Roof Slab including beams etc with Vent shaft , manhole openings with cover connection etc., complete with effective depth of 1.5 meter and overall depth of 3 meter. complete all as shown in TD drg No TD 576 sheet 1/2 and 2/2 and TD 217 sheet 1/2 and 2/2 , specified and directed.

All as per item no. 185 above of Septic tank (3.00m overall depth) but overall depth exceeding beyond 3.00m and upto 4.50 m complete all as directed and specified. Note:- The tenderer shall quote rates for per meter of depth beyond 3.00m and upto4.50m. Actual payment shall be made based on actual depth provided at site for one meter depth or part thereof . Tenderer should note this aspect while quoting rates against this item.

All as per item no. 185 above of Septic tank (3.00m overall depth) but overall depth exceeding beyond 4.50m and upto 6.00 m complete all as directed and specified. Note:- The tenderer shall quote rates for per meter of depth beyond 4.50m and upto 6.00m. Actual payment shall be made based on actual depth provided at site for one meter depth or part thereof . Tenderer should note this aspect while quoting rates against this item.

Taking down copper / aluminium point wiring (light, fan, socket or power) complete including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc removing materials to store for keeping in safe custody or taking credit and making good the disturbed surfaces of walls, floors, etc. complete all as specified and as directed.

Taking down DBs any type and size including MCBs removing materials to store for keeping in safe custody or taking credit and making good the disturbed surfaces of walls, floors, etc. complete all as specified and as directed.

Material and labour for point wiring with 1.5 Sq.mm nominal cross sectional area, single core, 1100 Volts grade, multi-stranded, PVC insulated, unsheathed FRLSH copper conductor cable with and including continuous earth wire of size 1.5 Sqmm nominal cross sectional area, single core, 1100 Volts grade, multi-stranded, PVC insulated, unsheathed, FRLSH copper conductor cable and connected to common earth and earth dolly with suitable copper lugs and drawing into and including rigid non-metallic PVC conduit of 20mm dia or higher, medium grade complete with and including all PVC conduit accessories concealed into wall by cutting of chases in wall and replacement of sunken box for modular switches/sockets, regulators etc and making good to the disturbed surfaces to match with the existing finishes complete all as specified and directed for one light / fan point controlled by one switch complete all as specified and as directed.

All as per srl item No 190 above but one bell / buzzer point controlled by one bell push button on the same board with other switches or independent with cable 1.5 Sq mm size.

All as per srl item No 190 above but one light point controlled by two, two way switches with cable 1.5 Sq mm size.

All as per srl item No 190 above but one 3 pin socket outlet, 05 Amps, independent with cable 1.5 Sq mm size.

All as per srl item No 190 above but one 3 pin socket outlet 05 Apms point on the same board with other switches with cable 1.5 Sq mm size.

All as per Serial item No 190 above but one 3 pin socket outlet, 15 Amps, independent with cable 2.5 Sq mm size.

Supply and fixing Modular switch 1 way 6A, 1 module complete all as specified & directed.

Supply and fixing Modular Bell push 6A 1 module complete all as specified & directed.

Supply and fixing Modular switch 1 way 16A, 1 module complete all as specified & directed.

Supply and fixing Modular switch 2 way 6A, 1 module complete all as specified & directed.

Supply and fixing modular Socket, 6A - 2/3 pin combined 2 module complete all as specified & directed.

S&F modular Socket 6A/16A - 2/3 pin combined 2 module complete all as specified & directed.

Supply and fixing Fan step regulator, 120W - 2 module (Modular) complete all as specified & directed.

Supply and fixing white cover plate with frame modular type of 03 module

Supply and fixing white cover plate with frame modular type of 04 module

Supply and fixing white cover plate with frame modular type of 06 module

Supply and fixing white cover plate with frame modular type of 08 module

Material and labour for point wiring with 1.5 Sq.mm nominal cross sectional area, single core, 1100 Volts grade, multi-stranded, PVC insulated, unsheathed FRLSH copper conductor cable with and including continuous earth wire of size 1.5 Sqmm nominal cross sectional area, single core, 1100 Volts grade, multi-stranded, PVC insulated, unsheathed, FRLSH copper conductor cable and connected to common earth and earth dolly with suitable copper lugs and drawing into and including rigid non-metallic PVC conduit of 20mm dia or higher, medium grade complete with and including all PVC conduit accessories concealed into wall by cutting of chases in wall and replacement of sunk zinc coated pressed steel terminal box of 1.60mm thick with 3mm thickness, plastic laminated sheet top cover, brass screws, cup washers etc and making good to the disturbed surfaces to match the existing complete all as specified and directed for one light / fan point controlled by one switch complete all as specified and as directed.

All as per srl item No 207 above but one bell / buzzer point controlled by one bell push button on the same board with other switches or independent with cable 1.5 Sq mm size.

All as per srl item No 207 above but one light point controlled by two, two way switches with cable 1.5 Sq mm size.

All as per srl item No 207 above but one 3 pin socket outlet, 05 Amps, independent with cable 1.5 Sq mm size.

All as per srl item No 207 above but one 3 pin socket outlet 05 Apms point on the same board with other switches with cable 1.5 Sq mm size.

All as per Serial item No 207 above but one 3 pin socket outlet, 15 Amps, independent with cable 2.5 Sq mm size.

Supply and fixing switch piano flush type, single pole, one way, 05 Amps complete all as specified & directed.

Supply and fixing bell push, flush type, 05 Amps complete all as specified & directed.

Supply and fixing switch piano flush type, single pole, two way, 05 Amps complete all as specified & directed.

Supply and fixing socket outlet 2 in 1, 5 pin, 05 Amps complete all as specified & directed.

Supply and and fixing switch socket combination 2 in 1, 3 pin, 05 and 15 Amps, flush type, universal complete all as specified & directed.

Supply and fixing stepped type, electronic fan regulator, flush and socket type on the existing phenolic laminated sheet etc as required complete all as specified & directed.

Supply and fixing bell, AC, 230 volts, single pole complete all as specified & directed.

S&F angle type holder insulated body with back plate suitable for batten fittings complete all as specified and as directed.

Supply & fix LED down lighter, 12 W complete all as specified and as directed.

Supply & fixing bulk head light fitting made from cast aluminium body with heat resistance pressure die cast housing, IP-65 protection cover suitable for bulk head fitting integrated type 6.5 W LED, 6000K , 105 lumens/watt including inbuilt electronic driver complete all as specified and as directed.

Supply and Fixing wall/surface mounting luminaires integrated LED Batten 20 W, 6000 K,100 lumens/watt , 230V with extruded Aluminium housing 4 feet long with frosted PMMA/PC diffuser & integrated electronic driver complete including Electrical connection with PVC three core copper flexible wire & all necessary fixing arrangements complete all as specified and as directed.

S&F in repair LED Building security light 35/40 Watt with high power LED source (>110lumen/watt) PDC housing, IP65 and IK 07 with 4 KV inbuilt surge protection potted driver including Electrical connection with PVC three core copper flexible wire & all necessary fixing accessories such as bracket of GI pipe light grade 40 mm dia 0.60 mtr long bend to shape as per suitable size along with all accessories, fixed on wall including bolts & nuts complete all as specified and as directed.

Supply and fix ceiling rose, 3 terminals, polycarbonate body complete all as specified & directed.

Supply and fix sheet metal enclosure distribution board, single pole and neutral, AC, 240 volts, 08 way with 200 Amps rated bus bar and double door protection grade IP 43 in fine powder coated, matt finish with best CRCA sheet, fitted with shrouded neutral, insulated pin type copper bus bar, Din rail, earth bar confirming to IS 13032 & 8623 complete all as specified and directed.

Supply and fixing of MCB with MCB SP, 06 to 32 Amps 240 volts, 'C' Series, ISI marked and conforming to IS 8828/IEC 60898-1 including making connections with copper lugs, testing as required complete all as specified and directed.

Supply and fixing of MCB SPN, 32 Amps 240 volts, 'C' Series, ISI marked and conforming to IS 8828/IEC 60898-1 including making connections with copper lugs, testing as required complete all as specified and directed.

Supply and fixing of MCB SPN, 63 Amps 240 volts, 'C' Series, ISI marked and conforming to IS 8828/IEC 60898-1 including making connections with copper lugs, testing as required complete all as specified and directed.

Taking down fan, sealing cable end, dismantling blades and removing fan and blades to sore including painting of ceiling fans complete, in situ with synthetic enamel paint by one coat spraying after cleaning all dust etc including filling cavities with filler and hanging only ceiling fan and connecting up including provision of cable from ceiling rose or connector to fan complete all as specified & directed.

S&F of exhaust fan single phase, 230/240 Volt heavy duty of size 300 mm sweep 1400 RPM including suitable louvers and making connection with twisted copper flexible wire 23/0.076mm all as specified and directed.

S & F water heater storage type electric BEE five star rated of capacity 25 ltrs to operate on 230 volt AC, vertical type including 4 Nos full threaded fastener of size 100x10 mm with, 2 No washer, water connection with 02 Nos PVC flexible pipe of size 15 mm, 450 mm lenght & suitable plug top of 16 Amp capacity complete all as specified and directed.

Supply and fix sheet metal enclosure with socket plug top and MCBs with atwo pin and earth plug and socket complete with one MCB 20 Amp complete all as specified and directed.

Supply only LED bulb 7/9 watt complete all as specified and directed.

Refixing of tube light fitting removed in item item No 235 above including electrical connection with PVC three core copper flexible wire and all necessary fitting arrangement all as complete all as specified and directed.

Taking down exhaust fan of any size including louvers and making good to the disturbed surface of walls and deposit to AGE E/M store yard for safe custody and refixing including electrical connection with three core copper flexible wire complete all as specified and directed.

Supply & fix exhaust fans, plastic body, AC, single phase, 230/240 V of size 200 mm sweep with louver complete all as specified and directed.

M&L for Cutting, opening circular/Rectangular in shape hole on wall for fixing of exhaust fan of size 300/200 mm sweep incl plastering and making good the disturbed surface surrounding complete all as specified and directed.

Supply & fix wall fan, 300 mm sweep, AC, single phase, 230/240 V, 1400 RPM complete all as specified and directed.

S& F Decorative wall light fixture made up of Metal base, synthetic white in colour and square/round metal base with bend pipe and glass globe with nickel finish, ( B-22/E27 base), with 01 No. 7/9 W LED Bulb, 230 V, 6000K, complete incl all required electrical connecting arrangements all as specified and as directed. Make Phillips Model Grace or Jaquar lighting Cat part No JNL-NKL-WLBPGG001E27/ Havells decorative model Floretine WL 1LS B22 SS Cat part No LHFOAJE1TZ1I060

Supply and fixing wall/surface mounting luminaires (Mirror Light) integrated LED Batten( 2 feet) 10/12 W, 6500 K, 230V ,100 lumens/watt,with extruded aluminium housing & integrated electronic driver complete including Electrical connection with PVC three core copper flexible wire & all necessary fixing arrangements complete all as specified and directed.

Taking down geyser of any size including connected items and making good to the disturbed surface of walls and deposit to AGE E/M store yard for safe custody complete all as specified and directed.

Taking down electric meter and refixing the same in its original or new location as directed, fixed on new board and providing electrical connection including provision of cable lugs complete all as specified & directed

Supply and fix modular type blanking plates, one module complete all as specified

M&L for disconnecting of electrical supply and taking down VTPN 4 way double door including MCCB and MCBs and kept in store for reuse incl civil work and painting of VTPN complete in situ with synthetic enamal paint by spraying painting one coat after cleaning all dust etc and refixing VTPN and connecting up including provn of cable lugs complete all as specified and directed.

S&F in replacement of sheet metal enclousre distribution board TPN (VTPN) ,AC 440 volt , 04 way with 200 amp rated bus bar and metal door with IP-54 & IK-09 protecting alongwith cable end box for above DB and flush to wall including all cutting etc in wall and making good to the disturbed surfaces to match the exiting complete all as specified and directed and comprising of rhe following (a) MCCB 125 amp , 04 pole. AC 415 volts og 16 KA breaking capacity complrte -01 No (b) MCB , SP , AC ,240 volt of 06-32 amp , C-curve , 10 KA breking capacity -12 Nos

Earthing complete with galvanized steel earth plate electrode 60 cm x 60 cm x 6 mm thick buried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of the plate not less than 1.5 mtr below normal ground level surrounded from all sides by 15 cm thick packed layer of charcoal dust and common salt filling in alternate layers and electrode connections by mean of GI wire 4 mm dia by means of bolts, nuts check nuts and washers of GI or steel and connecting to earthing test point, main switch board, testing on completion including PCC cover and frame, PCC (1:3:6) type C-2 as in earthing pit, MS funnel with wire mesh GI pipe 20 mm dia light grade for watering and GI pipe 20 mm dia light grade for the protection of GI wire from earth pit to earth point complete including necessary excavation and earth work in any type of soil, returning, filling in approved soil and disposal of surplus soil to a distance n.exc 50 m all as specified as shown in electrical plate No 5 SSR Part-I. PCC chamber shall be constructed at least one metre away from the earth pit and GI pipe fittings for watering shall be provided up to chamber and cost of the same is deemed to be included in the rate of earthing. Note :- Test result should be vary max up to 5 ohm / satisfied of user.

LUMOS INFRA PVT LTD

GANGA INFRABUILD PVT LTD

AKM CONSTRUCTION AND ENGINEERING LLP

RAGHUSONS INFRA ENGINEERING PVT. LTD

NARSINGH DEVELOPERS LLP

NAND LAL PURI AND SONS PRIVATE LIMITED

SAWHNEY BUILDWELL LLP

SHRI GURMUKHDAS CONTRACTORS PVT. LTD.

M/s Madan Lal Bansal and Co. Contractors Pvt. Ltd.