Interior Fit-Out Works of SIDBI Office at Sitapura, Jaipur, Rajasthan

NAME OF WORK: BOQ FOR THE INTERIOR FIT OUT WORKS OF SIDBI SITAPURA BO JAIPUR

Total Amount DSR

Total Amount DSR

Sr.No Description DSR Amount Non- DSR Amount

5 Fire Fighting Work 48,935.00 40740.00 89,675.00

9 Lighting Work 149,940.00 149,940.00

Total (DSR +MR) BOQ Amount 6,063,364.00

GRAND TOTAL (I/C GST) 6,063,364.00

GRAND TOTAL (I/C GST) 6,063,364.00

Digitally signed by AMIT

SCHEDULE OF QUANTITIES - CIVIL WORKS

S NO DSR/MR DESCRIPTION UNIT QUANTITY RATE AMOUNT AMOUNT

DSR 2023 VOL-1 DSR RATE NON DSR

CIVIL & INTERIOR WORKS

Dismantling tile work in floors , Wall and roofs laid in cement mortar including

stacking material within 50 metres lead.

For thickness of tiles above 25 mm and up to 40 mm

Demolishing brick work manually / by mechanical means including stacking of

serviceable material and disposal of unserviceable material within 50 metres lead

as per direction of Engineer-in-Charge.

15.7.4 In cement mortar CUM 1.00 2,060.20 2,060.20

Carriage of material by mechanical transport including loading unloading and

1.1.1 Lime, murrum, building rubbish

2 MASONRY AND PLASTER

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone

2.1 11.3 aggregate) finished with a floating coat of neat cement, including cement slurry,

but excluding the cost of nosing of steps etc. complete.

11.3.1 40 mm thick with 20 mm nominal size stone aggregate SQM 5.00 614.20 3,071.00

CEMENT PLASTER :- 15 mm cement plaster on the rough side of single or half brick

2.5 13.4 12 mm cement plaster of mix

POP PUNNING (12mm-15mm) : Providing and fixing Average 12mm to 15mm thick

2.6 MR POP Punning over cement plaster in line & plumb finished smooth to receive SQM 100.00 301.33 30,132.62

paint. (Internal surfaces of walls).

3 FLOORING WORKS

ALUMINIUM SKIRTING: Supply of 100mm Aluminium (Grade 6063) Skirting with 15 micron

3.01 MR anodising In Natural Finish. Thickness 1.30 to 1.50mm. Designed to conceal screws. metre 30.00 325.00 9,750.00

Seamless finish. Complete with Rubber/ PVC Jointers and Gasket.

Supplying and fixing of 3mm Luxury vinyl flooring Top layer of approved design & Pattern

as per architects approval & Instructions

Digitally signed by AMIT

S NO DSR/MR DESCRIPTION UNIT QUANTITY RATE AMOUNT AMOUNT

DSR 2023 VOL-1 DSR RATE NON DSR

CARPET TILES: Providing and laying carpet tile flooring. Carpets shall be of Type 6 nylon

loop pile carpet tiles/Plank. The carpet shall have sufficient gauge (1/10 ~ 1/12) with

sufficient stitches (10~13) per inch. The carpet shall be solution dyed fibre content or with

injection printing technology. The carpet shall have the pile height ranging from (2.0 ~

3.0) mm with average density higher than 4500 Oz/ cubic yard. The total thickness

of the carpet tile shall also range from (5.5 ~ 6.0) mm.

4 FALSE CEILING WORKS

GYPSUM BOARD CEILING: Providing and fixing false ceiling at all height including

providing and fixing of frame work made of special sections, power pressed from

M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per

IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of

27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with

dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed

to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required

size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm

running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm

thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of

10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to

G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long

G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high

having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to

wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall

screws @ 230 mm interval, including fixing of gypsum board to ceiling section and

perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c,

including jointing and finishing to a flush finish of tapered and square edges of the

board with recommended jointing compound , jointing tapes , finishing with jointing

compound in 3 layers covering upto 150 mm on both sides of joint and two coats of

primer suitable for board, all as per manufacturer's specification and also including

the cost of making openings for light fittings, grills, diffusers, cutouts made with

frame of perimeter channels suitably fixed, all complete as per drawings, specification

and direction of the Engineer in Charge but excluding the cost of painting with

12.5mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011

(Board with BIS certification marks)

Providing & fixing of Silhoutee Frame ceiling tile in size 600x600x15mm having noise

reduction co-efficient of 0.7, Density of 100 kg / m3, and Humidity resistance of 95% to be

4.02 MR laid on exposed grid system with white wrap comprising main runner 3.00 mm x 24mm sq m 50.00 2450.00 122500

web height cross tee 1.2 mtrs x 24 mm web height and 0.6 mtrs x 24 mm web height. The

wall angle shall be 3.0 mtrs.

Digitally signed by AMIT

S NO DSR/MR DESCRIPTION UNIT QUANTITY RATE AMOUNT AMOUNT

DSR 2023 VOL-1 DSR RATE NON DSR

5 PARTITIONS AND WALL CLADDING

WALL PANELING :-Providing and fixing Paneling upto ceiling height consisting of

Aluminium frame and required board, frame work made of Aluminium section made of

50x25 mm , consisting of floor and ceiling channel 50mm wide having equal flanges of 25

mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to

centre with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener

or metal screws with nylon plugs and the studs 48 mm wide having one flange of 34

mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and

ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia

bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with

5.01 MR suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to

centre, and fixing of boards to both side of frame work by 25 mm long dry wall screws on

studs, floor and ceiling channels at the spacing of 300 mm centre to centre. The boards

are to be fixed to the frame work with joints staggered to avoid through cracks, M.S.

fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm each) to be

provided at the horizontal joints of two boards, fixed to the studs using metal to metal

flat head screws, including jointing and finishing to a flush finish with recommended

jointing compound, jointing tape, angle beads at corners (25 mm x 25 mm x 0.5 mm), joint

finisher as per manufacture's specification and direction of engineer in charge all

Paneling with 11- 12 mm thick HDHMR board to IS: 5509 sq m 52.00 2,414.28 125542.56

Digitally signed by AMIT

S NO DSR/MR DESCRIPTION UNIT QUANTITY RATE AMOUNT AMOUNT

DSR 2023 VOL-1 DSR RATE NON DSR

WALL PARTITION-Providing and fixing partition upto ceiling height consisting of

Aluminium frame and required board, frame work made of Aluminium section made of

50x25 mm , consisting of floor and ceiling channel 50mm wide having equal flanges of 25

mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to

centre with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener

or metal screws with nylon plugs and the studs 48 mm wide having one flange of 34

mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and

ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia

bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with

5.02 MR suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to

centre, and fixing of boards to both side of frame work by 25 mm long dry wall screws on

studs, floor and ceiling channels at the spacing of 300 mm centre to centre. The boards

are to be fixed to the frame work with joints staggered to avoid through cracks, M.S.

fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm each) to be

provided at the horizontal joints of two boards, fixed to the studs using metal to metal

flat head screws, including jointing and finishing to a flush finish with recommended

jointing compound, jointing tape, angle beads at corners (25 mm x 25 mm x 0.5 mm), joint

finisher as per manufacture's specification and direction of engineer in charge all

Both side 12 mm thick HDHMR board to IS: 5509 sq m 110.00 3450.00 379500

LAMINATE CLADDING- P/F 1mm thick laminate including 4 mm thick MDF, on an existing

Plywood surface.

Providing and fixing 12mm thick frameless toughened glass door shutter of approved

brand and manufacture, including providing and fixing top & bottom pivot & double

5.04 21.18 acting hydraulic floor spring type fixing arrangement and making necessary holes etc. for sq m 10.00 5325.9 53259.00

fixing required door fittings, all complete as per direction of Engineer in charge (Door

handle, lock and stopper etc. to be paid separately)

Providing and fixing partition comprising 12 mm thick clear toughened safety glass of

approved make conforming to IS 2553 (Part-I) and IS 14900, fixed in anodized aluminium U-

channels of approved size and section at top, bottom and sides as required. The work

MR shall include machine polished exposed edges of glass, neoprene packing, EPDM sq m 21.00 3560 74760.00

gaskets, silicone sealant, aluminium channels, screws, fasteners, anchoring arrangements,

cutting, handling, transportation, installation, cleaning and all incidental works complete

as per approved drawings and direction of Engineer-in-Charge.

Digitally signed by AMIT

S NO DSR/MR DESCRIPTION UNIT QUANTITY RATE AMOUNT AMOUNT

DSR 2023 VOL-1 DSR RATE NON DSR

Providing wood work in frames of doors, windows, clerestory windows and other frames,

5.05 9.1 wrought framed and fixed in position with hold fast lugs or with dash fasteners of

required dia & length (hold fast lugs or dash fastener shall be paid for separately).

9.1.1 Second class teak wood cum 0.25 142949.7 35788.89

Providing and fixing partition top beading 80x12 mm, including cutting, shaping,

adhesive/fastener fixing, edge finishing, surface preparation, and applying polish with

matching finish, complete in all respects as per site requirement and engineer-in-charge

INSULATION- Providing and fixing thermal insulation with Resin Bonded rock wool

conforming to IS: 8183, having density 48 kg/m3,50 mm thick,wrapped in 200 G Virgin

Polythene Bags fixed to wall wirh screw, rawel plug & washers and held and in position by

criss cossing GI wire etc. complete as per directions of Engineer-in-Charge.

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-

decorative type, core of block board construction with frame of 1st class hard wood and

well matched commercial 3 ply veneering with vertical grains or cross bands and face

veneers on both faces of shutters:

9.21.1 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws sq m 10 2,392.65 23926.50

Providing and applying panelling/partition with matching colour groove finish and

polishing, including all materials, labour, surface preparation, fixing accessories, edge

finishing, sanding, colour matching, groove cutting, polishing coats, and complete

finishing as per site requirement and engineer-in-charge directions.

TOWER BOLTS:- Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic

AC 10 as per IS : 1868 ), transparent or dyed to required colour or shade, complete:

DOOR STOPPER:- Providing and fixing bright finished brass hanging type floor door

stopper with necessary screws, etc. complete.

Door Closers: Providing and fixing aluminium extruded section body tubular type universal

hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door

weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed

adjustment with necessary accessories and screws etc. complete.

MORTICE LOCK AND LEVER HANDLES- Providing and installing Tubular Handle TH 123

5.14 MR with Roses & Escutcheon in SS packaged with Mortice lockset 55mm backset, 20 SS EACH 5 2,650.00 13,250.00

forend, SS strike plate and EP Cylinder for all flush doors.

Providing and fixing 600 mmx25 mm H Type handle for Doors approved make and designs

as per engineer in charge

Digitally signed by AMIT

S NO DSR/MR DESCRIPTION UNIT QUANTITY RATE AMOUNT AMOUNT

DSR 2023 VOL-1 DSR RATE NON DSR

Providing and fixing minimium 70-90 kg capacity flooor spring for Doors approved make

and designs as per engineer in charge

Providing and fixing Glass door lock approved make and designs as per engineer in

5.18 MR Providing and fixing Glass Big -L approved make and designs as per engineer in charge each 2 2,450.00 4,900.00

Providing and applying plaster of paris putty of 2 mm thickness over plastered

surface to prepare the surface even and smooth complete.

Wall painting with premium acrylic emulsion paint of interior grade, having VOC

(Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and

manufacture, including applying additional coats wherever required to achieve even

shade and colour.

Applying priming coats with primer of approved brand and manufacture, having low

VOC (Volatile Organic Compound ) content.

With ready mixed pink or grey primer on wood work (hard and soft wood) having VOC

content less than 50 grams/ litre

Painting with synthetic enamel paint of approved brand and manufacture of required

colour to give an even shade :

13.99.1 One or more coats on old work. sq m 85 102.80 8738.00

FROSTEDFILM(CRYSTALQUALITY):-Providing and fixing scotchcal over glass surface as

approval of the Architect. (Only film surface area shall be measured and paid).

Providing & fixing Sidbi Signages & Logo & Sidbi Enviremoent Theme as per Direction of

Engineer in Charge

Providing & fixing Sidbi Sign Glow Board For Exterior Acrylic Base Embeded Letter as per

design (Front approx = 21 x 4)

Providing and fixing sandwich poster made of printed graphic mounted on required

thickness sunboard/ACP board, fixed directly on wall with SS decorative studs, complete

with all necessary hardware, fitting, and installation at site, as per approved design and

direction of engineer-in-charge.

Digitally signed by AMIT

S NO DSR/MR DESCRIPTION UNIT QUANTITY RATE AMOUNT AMOUNT

DSR 2023 VOL-1 DSR RATE NON DSR

GYPSUM PARTITIONING:- Providing and fixing partition upto ceiling height consisting

of G.I. frame and required board, including providing and fixing of frame work

made of special section power pressed/ roll form G.I. sheet with zinc coating of

120 gms/sqm(both side inclusive), consisting of floor and ceiling channel 50mm

wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at

the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter

50 mm length or suitable anchor fastener or metal screws with nylon plugs and the

studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50

mm thick fixed vertically within flanges of floor and ceiling channel and placed at a

spacing of 610 mm centre to centre by 6 mm dia bolts and nuts, including fixing of studs

along both ends of partition fixed flush to wall with suitable anchor fastener or

metal screws with nylon plugs at spacing of 450 mm centre to centre, and fixing of

boards to both side of frame work by 25 mm long dry wall screws on studs, floor and

ceiling channels at the spacing of 300 mm centre to centre.

The boards are to be fixed to the frame work with joints staggered to avoid through

cracks, M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm

each) to be provided at the horizontal joints of two boards, fixed to the studs using metal

to metal flat head screws, including jointing and finishing to a flush finish with

recommended jointing compound, jointing tape, angle beads at corners (25 mm x

25 mm x 0.5 mm), joint finisher and two coats of primer suitable for board as per

manufacture's specification and direction of engineer in charge all complete.

75 mm overall thickness partition with 12.5 mm thick double skin fire rated Glass

Reinforced Gypsum (GRG) plaster board conforming to IS: 2095:

Providing and fixing gypsum board vertical bend in required radius/shape using 12.5mm

5.33 MR thick gypsum board over GI framework (stud/channel), including cutting, bending, fixing, Rmtr 40 195.00 7800

joint treatment with tape and compound, finishing complete in all respect

Add labour cess @0.973 as per CPWD circular 436,442.30

Add CPWD cost index @103 on DSR civil 2023 449,535.57

Total Amount DSR & NDSR 1,940,284.06

Total Amount DSR & NDSR 1,940,284.06

Digitally signed by AMIT

SCHEDULE OF QUANTITIES - ELECTRICAL WORKS

S NO DESCRIPTION UNIT QUANTITY RATE

2025 DSR (INR)

A POINT WIRING

Wiring for light point/ fan point/ exhaust fan point/call bell point with 1.5 sq.mm FRLS PVC insulated

copper conductor single core cable in surface/ recessed medium class PVC conduit, with modular

A.1 switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated

copper conductor single core cable etc as required.

Wiring for group controlled (looped) light point/ fan point/call bell point (without independent switch

etc.) with1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed PVC

A.2 conduit, and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core

cable etc as required.

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in

A.3 1.12 surface/ recessed medium class PVC conduit alongwith 1 No 4 sq. mm FRLS PVC insulated copper Metre 240 373.00 89520.00

conductor single core cable for loop earthing as required.

Supplying and fixing following modular switch/socket on the existing modular plate & switch box

including connections but excluding modular plate etc. a srequired.

1.24.4 3 pin 5/6 amp socket outlet Each 50 136.00 6800.00

1.24.5 6 pin 15/16 amp socket outlet Each 14 219.00 3066.00

Digitally signed by AMIT

S NO DESCRIPTION UNIT QUANTITY RATE

2025 DSR (INR)

Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding

modular plate as required.

Supplying and fixing following size/module, GI box along with Modular base & cover plate on existing

modular metal boxes etc. as required.

B SUBMAIN AND CONTROL WIRING

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FR PVC

1.14 insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as

1.14.1 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire Metre 210 267.00 56070.00

1.14.4 2 X 6 sq. mm + 1 X 6 sq. mm earth wire Metre 20 482.00 9640.00

1.14.11 4 X 16 sq. mm + 2 X 6 sq. mm earth wire Metre 35 1454.00 50890.00

Supplying and making end termination with brass compression gland and aluminium lugs for following

11.1 size of PVC insulated and PVC sheathed/ XLPE aluminium conductor cable of 1.1 KV grade as

Supply of following XPLE armourned 1.1 KV grade conforming to I.S.7098/1554Aluminium Conductor

Digitally signed by AMIT

S NO DESCRIPTION UNIT QUANTITY RATE

2025 DSR (INR)

C.2 Supply of following sizes of PVC sheathed PVC/XLPE insulated Aluminium conductor armoured cable of

1.1KV grade conforming to IS:7098 part-1/IS:1554 part-1 respectively & ISI marked.

(b) 3.5 C x 95 Sqmm XLPE cable RM 10 762.00 7620.00

(e) 3.5 C x 35 Sqmm XLPE cable RM 10 366.00 3660.00

Supply of following sizes of copper cables -PVC sheathed PVC/XLPE insulated Copper conductor

armoured cable of 1.1 KV grade conforming to IS:7098 part-1 / IS:1554 part-1 respectively & ISI marked.

(a) 4 C x 16 Sqmm XLPE copper cable RM 34 1300.00 44200.00

(b) 4 C x 25 Sqmm XLPE copper cable RM 8 1800.00 14400.00

D.1 2.11 Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required. Each 5 14.00 70.00

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable

2.10 for inductive load of following poles in the existing MCB DB complete with connections, testing and

D.2 commissioning etc. as required.

Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with

connections, testing and commissioning etc. as required.

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution

board, 415 V, on surface/recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din

bar, interconnections, powder painted including earthing etc. as required. (But without MCB/ RCCB/

Digitally signed by AMIT

S NO DESCRIPTION UNIT QUANTITY RATE

2025 DSR (INR)

Providing and fixing 400mm wall mounted oscillating fan, heavy-duty type, 230V, 50Hz, single phase,

with three-speed control regulator, complete with suitable mounting brackets, clamps, bolts, nuts, and

MR necessary wiring connections from the nearest point using 1.5 sq.mm copper flexible wire, including Each 5 3950.00 19750.00

testing and commissioning at site, complete as required.( Make: Havells/Cromton/Usha/Bajaj

asapproved by ingineer-in-charge)

Supplying and fixing of following sizes medium class PVC conduit aong with accessories in surface/

E.12 recess including cutting the wall and making good the same incase of recessed conduit as required

Supplying and Installation of following size perforated of painting with powder coating M.S. cable trays

E.13 4.1 of perforation of not more than 17.5% in convinient sections, joined with connectors suspended from

the cieling with MS suspenders including bolts and nuts painting suspenders etc as required

4.1.6 450 mm width x 50 mm depth x 2 mm thickness Metre 5 1243.00 6215.00

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing

F.1 5.6 masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long SET 2 15004.00 30008.00

etc. with charcoal/coke and salt as required.

Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. As

F.3 5.15 Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required. MTR 15 287.00 4305.00

Digitally signed by AMIT

S NO DESCRIPTION UNIT QUANTITY RATE

2025 DSR (INR)

Online UPS- Input supply: Three Phase, Output

supply: Three Phase.

Supplying, installation, Testing & Commissioning of

following capacity at full load (Unity Power Factor)

at operating temperature 0 to 40 0C, Relative

humidity 0 to 95%, Online double conversion true

sine wave Uninterrupted hot swapable (allow for the

replacement or addition of battery modules without

shutting down the entire system) modular Power

Supply (UPS) system with N+1 modules (N denotes

total number of modules required for rated capacity).

The UPS shall include a Rectifier, inverter, battery

bank suitable for 30 minutes back up (Battery VAH

capacity shall not be less than 1600 VAH per KVA of

UPS rating per Hour backup time) on full load

(Battery shall be VRLA, SMF in ABS Container) and

Static Bypass switch along with provision for manual

bypass, suitable isolation transformer for additional

protection against neutral faults etc. UPS shall have

inbuilt phase sequence correction. The UPS

systems offered are to be of the latest technology

with Digital Control Microprocessor based for

190 DELHI SCHEDULE OF RATES (E&M)-2025

reliable operation using Insulated Gate Bipolar

Transistor (IGBT)'s both for the rectifier & inverter

(3 Level) with PWM (Pulse Width Modulation). The

quality of design, manufacturing and inspection

process should confirm to the relevant Inter-national

Providing & Fixing exhaust fan of approved make and size complete with frame, mounting

MR arrangement, necessary wiring connection from nearby point, screws, fasteners, cutting/fitting work and Nos 2 2150 4300

testing & commissioning complete as required at site

Supply, Installation, Testing and Commissioning of 3W LED Unidirectional Exit Signage Light with inbuilt Nos. 4 3775.75

2hours battery back up (Maintained type).

Total of Electrical items 827086 109033

Total Amount 827086.00 109033.00

Total Amount 827086.00 109033.00

Total DSR+NDSR 936119.00

Digitally signed by AMIT

1.0 VRF/VRV OUTDOOR UNIT Unit Quantity Rate DSR Amount

2025 Amount (A)

Supply, Installation, Testing & Commissioning of Modular type Variable Refrigerant Flow/Variable

Refrigerant Volume air cooled Outdoor units suitable for cooling /heating having 100%

hermetically sealed inverter type twin Rotary/Scroll Compressor(s),minimum two compressors (with

individual separate PCB) for above 14HP modules, microprocessor based Controller, top discharge

type condensing unit(s), with R-410-A Refrigerant or equivalent, vibration Isolators with suitable

foundation etc. complete as required. To have better efficiency condenser fan shall be capable

to operate at different speed with respect to load. The unit shall deliver the rated capacity and in

confirmation as per IS 18728:2024 and CPWD Specifications and work even at 50°C ambient

temperature without tripping. The system shall be able to deliver 100% of the rated capacity upto

39 Degree Celcius.The unit shall be suitable to work on 400V +/- 10%, 3 Phase, 50Hz AC power

supply and BMS compatible. The unit shall be filled with first charge of the refrigerant and ready

for use as required. The condenser should be coated with a hydrophilic film to prevent water

accumulation on the surface of the heat exchanger, enhance water dispersion, and reduce the

risk of degradation, thereby improving overall performance and durability. The Indian Seasonal

Energy Efficiency Ratio (ISEER) of the unit shall be as per Energy Conservation and Sustainable

Building Code (ECSBC) 2024 as below and complete as per CPWD specification, connections,

inter connections etc. as required. (For capacity <40 kWr ISEER 7.4, Capacity > 40 and <70 ISEER

7.5, Capacity > 70 ISEER 7.6 for Super ECSBC Building)

2.0 INDOOR UNIT

Supply, Installation, Testing and Commissioning of following minimum capacity 4 way Cassette

Type Indoor ceiling mounted unit equipped with synthetic washable media pre- filter, fan section

with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX Copper

coil, electronic expansion valve, outer cabinet, drain pump, grill, necessary supports, vibration

31.4 Isolation, Corded remote control etc., suitable for operation on single phase 230 V ± 10%, 50Hz

AC supply, complete, as required. The Indoor units must shut down upon receiving a singal

from the BMS System/Fire Signals. The system shall be capable to adjust air flow as per room

requirement in auto mode. The cooling capacity of indoor unit will be at air inlet conditions of 27

Degree C DB and 19 Degree C WB temperature. (Make will be same as of Outdoor)

Digitally signed by AMIT

1.0 VRF/VRV OUTDOOR UNIT Unit Quantity Rate DSR Amount

2025 Amount (A)

Supply, Installation, Testing and Commissioning of following minimum capacity High wall type

Indoor unit equipped with and comfort washable synthetic media pre-filter, fan section with

low noise fan/dynamically balanced blower, multispeed motor, coil section with DX copper

coil, electronic expansion valve, outer cabinet, cord less remote control, drain pan, necessary

31.8 accessories etc., suitable for operation on 230 V ± 10%, 50 Hz, single phase AC supply, complete

as required. The Indoor units must shut down upon receiving a singal from the BMS System/Fire

Singnals. The system shall be capable to adjust air flow as per room requirement automatically.

The cooling capacity of indoor unit will be at air inlet conditions of 27 Degree C DB and 19

Degree C WB temperature. (Make will be same as of Outdoor)

Supply , Installation, Testing and Commissioning of Air Cooled Hi Wall split type Air conditioners complete with

Indoor unit(IDU), Out door unit (ODU), surface / concealed copper Refrigerant piping with insulation (closed

cell elastomeric nitrile rubber tubular pipe section) upto 3 Mtr (IDU to ODU), copper power cable upto 3.5 Mtr

(IDU to ODU) i/c drain pipe R-32/R-410/ R407 Green Refrigerant, wireless Remote control, suitable for working

between 180-260V with low & high voltage cutoff and 50 hz ,1 phase AC supply capable of performing

cooling, dehumidification, air circulation of following capacity with Scroll / rotary compressor. The system

32.2 shall be able to deliver 100% of the rated capacity upto 42 Degree Celsius. Min 5 year

Original Equipment Manufacturer (OEM) warranty both compressor and Printed Circuit Board (PCB). Must

comply : Electrical cable IS 694 or IS 9968 temperature sensing control IS /International Electro technical

Commission (IEC) 60730, hermetic compressor IS 10617, heat exchanger IS 11329, capacitor IS 2993 and motor

IS 12615. Complete as per CPWD

specification and IS : 1391 Part II 2023. The system shall be able to operate up to 50 0C (out door ambient

32.2.2 1.0 TR with 5 Star BEE Rating Each 1 39196 39,196.00

REFRIGERANT PIPING

Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of

following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system,

complete with fittings, with suitable adjustable ring type hanger supports, jointing/brazing

including accessories, insulated with XPLE Class-O tubular insulation/with Class-O closed cell

elastometric nitrile rubber tubular sleeves sections of 19 mm thick insulation as given below for

Suction and Liquid lines, all accessories as per specifications etc. as required :

3 31.14.1 6.4 mm dia (OD) (Softdrawn) with tube thickness 1.2 mm with 19 mm thick insulation Rmt 75.00 256.00 19,200.00

3.2 31.14.2 9.5 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm Rmt 75.00 346.00 25,950.00

3.3 31.14.3 12.7 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm Rmt 50.00 487.00 24,350.00

3.4 31.14.4 15.86 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm Rmt 35.00 615.00 21,525.00

Digitally signed by AMIT

1.0 VRF/VRV OUTDOOR UNIT Unit Quantity Rate DSR Amount

2025 Amount (A)

3.5 31.14.5 19 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm Rmt 20.00 739.00 14,780.00

3.8 31.14.8 28.58 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm Rmt 15.00 1,157.00 17,355.00

3.10 31.14.10 34.9 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm Rmt 8.00 1,286.00 10,288.00

3.13 31.13.1 Indoor Units (y-joint) Each 6 4535 27,210.00

5 CONDENSATE DRAIN UPVC PIPE

Supply, installation, testing and commissioning of uPVC Pipe, complete with fittings, supports, U

trap arrangement, Clean Plug with 6mm nitrile insulation and accessories as per specifications,

Wiring for circuit/ submain wiring along with earth wire

with the following sizes of FRLS/HFFR PVC insulated

copper conductor, single core cable in surface/

recessed medium class PVC conduit as required.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc.,

10.16 including cutting, hoisting, fixing in position and applying a priming coat of approved steel

primer, including welding and bolted with special shaped washers etc. complete.

10.16.1 Hot finished welded type tubes kg 50.0 194.40 9,720.00

Supplying and fixing following rating, double pole,

(single phase and neutral), 240 V, residual current

circuit breaker (RCCB), having a sensitivity current 30

mA in the existing MCB DB complete with

connections, testing and commissioning etc. as

Total Amount 945,810.00 25,280.00

Total Amount 945,810.00 25,280.00

Total Amount 971,090.00

Total Amount 971,090.00

Digitally signed by AMIT

SCHEDULE OF QUANTITIES - DATA and VOICE WORKS

S NO Description UOM Qty Rate

Amount Amount (A)

A. 2025 UTP Components for Data

Supplying, drawing, Testing and commissioning of Cat6A UTP 4 pair, 23 AWG solid copper

cable in existing conduit/ on surface, U/FTP, LSZH, Non-

Plenum, Horizontal (solid) Cable suitable for high speed data networking application

supporting upto 10Gbps over a 100 meter channel. The 4 Unshielded Twisted Pairs (UTP)

1 1.53 cable with color coded insulation

for easy indentification should have FLAME PROPERTIES i.e. Flammability Test - IEC 60332-1,

Smoke Density - IEC 61034, LSZH standards compliance: ANSI/TIA-568 C.2, ISO/IEC 11801,

IEEE 802.3an, RoHS. Delay Skew should be < 45NS. The outer Cable Diameter should be 7.5 +

2 mm. Cable should have been tested and verified by UL/ ETL etc. complete as required.

1.53 1 Run Of Cable METRE 1250 74.00 92500.00

Supply , Installtion , Testing and Comissioning of I/O port for CAT6 cable termination at

Rack Side. Keystone Unshielded Outlet, 180DG C6, Blue

Supply, Installtion, Testing and Comissioning of I/O port for CAT6 cable termination at Rack

Side end Redantant . Keystone Unshielded Outlet, 180DG C6, Yellow

Supply , Installtion , Testing and Comissioning of CAT6 patch cord 2 Mtr (7 feet) for

4 MR information outlet (I/O) to end user Redantant device connectivity.High Speed Gigabit Nos. 30 420.00 12600

24AWG U/UTP Patch Cord Yellow, LSZH, C6, 2M (Yellow)

Supply , Installtion , Testing and Comissioning of CAT6 patch cord 2 Mtr (7 feet) for

5 MR information outlet (I/O) to Rack End Redantant device connectivity.High Speed Gigabit Nos. 30 420.00 12600

24AWG U/UTP Patch Cord Yellow, LSZH, C6, 2M (Yellow)

Supply, Installtion, Testing and Comissioning of 24 port Loaded Angled Staggred Jack Panel

for CAT6 cable termination at rack end. Data Active Redandant

Supply , Installtion , Testing and Comissioning of 2 Port British Style Shuttered Face Plate white for I/O

fixing at user side

8 MR SITC of 04 core OM3 Multimode fiber orange color 50/125, minimum bending radius 15x OD RM 30 229.17 6875.00

9 MR SITC of 24U Rack Each 1 25,000.00 25000

Digitally signed by AMIT

Supply, Installation, Testing & Commissioning of 24-Port Layer-2 Managed Gigabit Ethernet

Switch comprising 24 × 10/100/1000 Mbps RJ45 ports and 4 × Gigabit SFP uplink ports,

switching capacity not less than 56 Gbps, forwarding rate not less than 41.7 Mpps,

supporting IEEE 802.3, 802.3u, 802.3ab, VLAN (802.1Q), QoS, STP/RSTP/MSTP, IGMP Snooping,

Link Aggregation (LACP), Port Mirroring, DHCP Snooping, Access Control List (ACL), Jumbo

Frames, rack-mountable, complete with power cord, rack mounting accessories,

configuration, testing and commissioning, suitable for structured cabling and LAN

Total Amount 92500.00 128155.00

Total Amount 92500.00 128155.00

Total Amount DSR & NDSR 220655.00

Total Amount DSR & NDSR 220655.00

Digitally signed by AMIT

SCHEDULE OF QUANTITIES: FIRE PIPING, HYDRANTS, SPRINKLERS AND ACCESSORIES

S No 2025/ DESCRIPTION QTY UNIT RATE

AMOUNT AMOUNT (A)

DSR (INR) NON-DSR

Providing, laying, testing & commissioning of 'C' class

heavy duty MS pipe conforming to IS 3589/IS 1239

including Welding, fittings like elbows, tees, flanges,

27.7 tapers, nuts bolts, gaskets etc. and fixing the pipe on the

1 wall/ceiling with suitable clamp/support frame and

painting with two or more coats of synthetic enamel

paint of required shade complete as required :

Providing, fixing, testing & commissioning of 15mm dia

27.21 quartzoid bulb type sprinklers of rating 68 degree

centigrade with required accessories :

27.21.1 Pendant type 1 Each 599.00 599.00

Supplying, fixing, testing and commissioning of butterfly

valve of PN 1.6 rating with bronze/gunmetal seat duly ISI

marked complete with nuts, bolts, washers, gaskets

conforming to IS 13095 of following sizes as required :

Digitally signed by AMIT

Carefully Extending, lowering and repositioning the

existing sprinkler points from the existing fire fighting

sprinkler piping network to suit the revised false ceiling

layout, including providing and fixing required lengths of

GI/MS sprinkler drop pipes (up to 1.5 m average), fittings,

socket, nipple, reducer, clamps, hangers, cutting and

threading, refixing existing sprinkler heads, alignment with

ceiling tiles, testing, commissioning and making the system

operational complete as required and as directed by

Engineer-in-Charge.

Supplying, installation, testing & commissioning of

sprinkler flexible pipe (UL Listed) of stainless steel

complete with 15 NPT on reducer thread with

maximum working pressure of 175 PSI test pressure of

27.25 875 PSI (Burst) with branch line (Inlet) 25mm NPT

5 male thread to sprinkler head (Outlet) 15mm NPT

female thread with reducer, nipple, 2 side brackets,

center bracket, stockbar of following sizes

complete as required.

Providing and fixing ISI Marked of approved make

6 Fire Extinguishers complete with all accessories as per

manufacturer's specifications.

a) CO2 gas nozzle type - 9 Litre capacity (IS:15683). 1 NOS 12000.00 12000.00

Mechanical Foam gas cartridge type. 9 Kg capacity

ABC dry powder stored pressure type 6 kg capacity

Total Amount 89675.00

Total Amount 89675.00

Digitally signed by AMIT

SCHEDULE OF QUANTITIES - CCTV

TOTAL TOTAL AMOUNT

TOTAL TOTAL AMOUNT

S NO DSR/ MR DESCRIPTION UNIT QUANTITY RATE

A. CCTV DSR NDSR

Supply, Installation, Testing & Commissioning of 2MP IR IP H.265

Vandal Proof Dome camera with 2.8 to 12mm Motorised Lens,Smart

IR, up to 30M IR distance,Up to 120 dB WDR (Wide Dynamic

Range),3D DNR (Digital Noise Reduction),H.265+, H.265, H.264,

MJPEG,Corridor mode, Triple streams,3-Axis, IP67, IK10 Vandal

Resistant,Colour: 0.005Lux (F1.4, AGC ON), 0 Lux with IR,Video

Compression H.265+, H.265, H.264, MJPEG,Behavior Detection

Supply, installation testing and commissioning of Network Video

recorder Linux based to manage and control all the cameras from

2 MR control room. Software shall support maximum 16 channel with Nos 1 26500.00 26500.00

joystick controller. 256Mbps Bit Rate Input Max(up to 32-ch IP video), 2

SATA Interfaces, alarm I/O: 16/4, 1.5U case,19"

Supply, Installation, Testing & Commissioning of 4 TB Surveillance Grade

SATA Hard Disk Drive (HDD), 3.5-inch form factor, 7200/5400 RPM as per

manufacturer design, SATA III (6 Gb/s), specifically designed for 24×7 CCTV

3 MR surveillance applications, compatible with Network Video Recorder (NVR), Nos 1 12900.00 12900.00

complete with mounting, formatting, configuration, testing and

commissioning. Approved makes: Western Digital Purple, Seagate SkyHawk,

Toshiba S300 or equivalent.

Supply Installation Testing & Commissioning of 32 inch Full HD LED

monitor including wall mount brackets/ clamps/ desk mounting stand.

Digitally signed by AMIT

TOTAL TOTAL AMOUNT

TOTAL TOTAL AMOUNT

S NO DSR/ MR DESCRIPTION UNIT QUANTITY RATE

Supply, Fixing & Laying of CAT 6A UTP cable 23 AWG solid copper

5 conductors for Connectivity of Hub room to End Point.High Speed Gigabit METRE 400 74.00 29600.00

Ethernet U/UTP, 250 MHz, Class E, 23 AWG, Unshielded LSZH Cable, C6

6 MR SITC of HDMI cables 10 meters M2M etc all compelte. Nos 2 3500.00 7000.00

Supply, Installation, Testing & Commissioning of 16-Port Gigabit

Managed PoE Switch conforming to IEEE 802.3af/at PoE standards,

comprising 16 × 10/100/1000 Mbps RJ45 PoE ports and 2 × Gigabit SFP

uplink ports, minimum PoE power budget 240 W, switching capacity

7 MR not less than 36 Gbps, forwarding rate minimum 26.8 Mpps, VLAN, Nos 1 23760.00 23760.00

QoS, STP/RSTP, IGMP Snooping, port isolation, surge protection, rack-

mountable, complete with power cord, rack mounting accessories,

configuration, testing and commissioning, suitable for operation with

Total Amount 29600.00 145160.00

Total Amount 29600.00 145160.00

Total Amount DSR & NDSR 174760.00

Total Amount DSR & NDSR 174760.00

Digitally signed by AMIT

FIRE ALARM SYSTEM WORKS

S.NO. DESCRIPTION UNIT Qty RATE Amount

INTELLIGENT FIRE ALARM SYSTEM

Supplying, installation, testing & commissioning sector panel

suitable for following zones, complete with visual indications

for short circuit fault, open circuit fault, fire condition and all

other standard facilities as per IS:2189 with mimic diagram

for all area/zone covered, complete with all connections,

interconnections as required.

Supplying, installation, testing & commissioning of smoke detector with built in LED and

Mounting base complete withb all Connections etc. as required.

Supplying, installation, testing & commissioning of manual call boxes of MS construction in

28.1.3 Surface/ Recess with Stainless Steel chain & hammer Assembly complete with glass and Each 2.00 513.00 1026.00

push button etc. as Required.

Supplying, installation, testing & commissioning of response indicator on surface/recessed

MS Box having two LED, metallic cover complete with all connections etc as required.

Supplying, installation, testing & commissioning of Fire alarm Sounder with Facility to make

e) 28.1.6 annoucement, mountedc in M.S Box (16 SWG) with Hinged cover plate & Suitable for Each 2.00 600.00 1200.00

operation with Amplifier i/c line matching transformer etc complete as required .

Supply, Installation, Testing & Commissioning of LED Exit Signage, Single Side, 3W–5W, wall

f) MR mounted, 230V AC, inbuilt Li-ion/Ni-Cd battery backup (minimum 180 minutes), complete Each 6.00 2750.00 16500

with fixing accessories and connection from nearest lighting point

CABLING & WIRING

Supplying & laying of 2x1.5 sqmm fire alarm armoured cable,

600/1000V rated with annealed copper conductor having

XLPE insulation, steel wire armouring & FRLS/HFFR outer

sheath complete as required.

Total Amount 79161.00 16500.00

Total Amount 79161.00 16500.00

Total Amount DSR & NDSR 95661.00

Total Amount DSR & NDSR 95661.00

Digitally signed by AMIT

Sno. Item Specifications Unit Qty Rate Amount

Supplying and placing in position of main table as per photograph/drawing .The table shall be made out

of 25mm thick pre -laminated particle board of approved shade. The working and non working edges

shall be finished with machine pressed with 2mm PVC egdge banding. The table top shall be supported

with MS powder coated "C" shape leg of size 50mm x 50mm with connectors of size 40mm x 40mm.

The front modesty are made out of 18mm thick prelaminated particle board with 2mm thk pvc edge

banding. The table shall be provisioned with Side unit of overall size: 900mm(L) x 450mm(D) x

BO Incharge 675mm(H) . Side storage having a provision for three equal drawer unit and two openable shutter &

Table one open storage with shelf in it. The Side unit top shall be made out of 18mm thick pre laminated

particle board and rest all storage to be made out of 18mm thick pre laminated particle board.

Provision of Junction box, wire raceway and 6 module fliptop box for wire passing or as per site

requirement.Main Table Dimension (L)2100mm X (D) 900mm X (H)750mm overall Side Runer

Dimension (L)900mm X (D) 400mm X (H) 675mm

Supplying and placing in position of Back Storage as per photograph/drawing .The back storage shall

be made out of 25mm thick pre -laminated particle board of approved shade. The working and non

working edges shall be finished with machine pressed with 2mm PVC egdge banding. Back Storage

2 Back Storage Nos 1.00 23,500 23,500.00

Dimension (L)2100mm X (D) 400mm X (H)675mm

Supplying and placing in position of 360 degrees revolving high back chai. The chair of Size :-

(W)590mm X (D)505mm X (H)1180mm - 1280mm. The chair shall be ergonomically design contour

lumbar back design made of 12mm thick BWR plywood (IS Grade - 303 for seat and back) upholstered

BO High Back with leatheritte and cut foam. The chrome plated loop armrest with padded upholstery is provided for

3 extra comfort. The chair shall be provided with pneumatic height adjustment which shall have stroke of Nos 1.00 10,500 10,500.00

10.0 +/- 0.3 cm . Five star chrome base with nylon castors . Chair seat has foam of density 30- 35 (+/

2kg /m3) Dimensions The backrest has a foam of 28kg/m3.

Supplying and placing in position of medium back cantilever chair of size: (W)610mm X (D)505mm X

(H)990mm.A contemporary design with an all black finish, . Material & subtype:Premium Leatherette,

Colour & Colour Family:Black, Dimension(W)610mm X (D)505mm X (H)990mm, Back Type:Cantilever,

BO Visitor Back Base:Cantilever Frame, Base Type: Cantilever, Maximum Seating Height:19".The Seat & back are

Chair made up of 12mm thk hot pressed plywood upholstered with PVC with polyurethane foam, chair seat

has foam of density 32-35 kg/m3. The backrest has a foam of 28kg/m3.

Supplying, and placing in position of sofa with premium Leatherette upholstery adds class to the soft

cushioned backrest and seating. Material & subtype:Premium Leatherette, Colour & Colour Family:as

per requirement, Seating Height:16.14" ,Legs:Stainless Steel, Finish:Matte, Size:Compact,

2 seater sofa BO Style:Modern, Texture:Two Tone. steam beech solid wood have used for framing construction of sofa

5 Cabin/ .The seat cushion is made of multi layered foam of density 32-35 kg/m3. The seating cushion have Nos 2.00 30,000 60,000.00

Reception 2.75 & 1.75 inches of elastic webbing. The thread used is nylon bonded to provide lasting stitch

strength . The backrest has a foam of 28kg/m3 with polyster polyfill outer layer of 200 gsm. 2 seater

Dimension(L)1390mm X (D)750mm X (H)710mm

Digitally signed by AMIT

Sno. Item Specifications Unit Qty Rate Amount

Supplying and placing in position of main table as per photograph/drawing .The table shall be made out

of 25mm thick pre -laminated particle board of approved shade. The working and non working edges

shall be finished with machine pressed with 2mm PVC egdge banding. The table top shall be supported

with MS powder coated "C" shape leg of size 50mm x 50mm with connectors of size 40mm x 40mm.

The front modesty are made out of 18mm thick prelaminated particle board with 2mm thk pvc edge

banding. The table shall be provisioned with Side unit of overall size: 900mm(L) x 450mm(D) x

BO Incharge 675mm(H) . Side storage having a provision for three equal drawer unit and two openable shutter &

Table one open storage with shelf in it. The Side unit top shall be made out of 18mm thick pre laminated

particle board and rest all storage to be made out of 18mm thick pre laminated particle board.

Provision of Junction box, wire raceway and 6 module fliptop box for wire passing or as per site

requirement.Main Table Dimension (L)2100mm X (D) 900mm X (H)750mm overall Side Runer

Dimension (L)900mm X (D) 400mm X (H) 675mm

Supplying, and placing in position of Cofee/ Corner Table as per approved design Dimension(L)450mm

Reception X (D)450mm X (H)450mm

Supplying, and placing in position of Centre Table as per approved design Dimension(L)1150mm X

7 Centre Table Nos 1.00 16,500 16,500.00

Supplying and placing in position of main table as per photograph/drawing .The table shall be made out

of 25mm thick pre -laminated particle board of approved shade. The working and non working edges

shall be finished with machine pressed with 2mm PVC egdge banding. The table top shall be supported

with MS powder coated "C" shape leg of size 50mm x 50mm with connectors of size 40mm x 40mm.

The front modesty are made out of 18mm thick prelaminated particle board with 2mm thk pvc edge

banding. The table shall be provisioned with Side unit of overall size: 900mm(L) x 450mm(D) x

8 675mm(H) . Side storage having a provision for three equal drawer unit and two openable shutter & Nos 2.00 38,790 77,580.00

one open storage with shelf in it. The Side unit top shall be made out of 18mm thick pre laminated

particle board and rest all storage to be made out of 18mm thick pre laminated particle board.

Provision of Junction box, wire raceway and 6 module fliptop box for wire passing or as per site

requirement. Main Table Dimension (L)1500mm X (D) 900mm X (H)750mm overall Side Runer

Dimension (L)900mm X (D) 400mm X (H) 675mm

Supplying and placing in position of 360 degrees revolving high back chai. The chair of Size :-

(W)590mm X (D)505mm X (H)1180mm - 1280mm. The chair shall be ergonomically design contour

lumbar back design made of 12mm thick BWR plywood (IS Grade - 303 for seat and back) upholstered

with leatheritte and cut foam. The chrome plated loop armrest with padded upholstery is provided for

9 AGM Chair extra comfort. The chair shall be provided with pneumatic height adjustment which shall have stroke of Nos 2.00 10,500 21,000.00

10.0 +/- 0.3 cm . Five star chrome base with nylon castors . Chair seat has foam of density 30- 35 (+/

2kg /m3) Dimensions The backrest has a foam of 28kg/m3.

Supplying and placing in position of medium back cantilever chair of size: (W)610mm X (D)505mm X

(H)990mm.A contemporary design with an all black finish, . Material & subtype:Premium Leatherette,

Colour & Colour Family:Black, Dimension(W)610mm X (D)505mm X (H)990mm, Back Type:Cantilever,

AGM Visitor Base:Cantilever Frame, Base Type: Cantilever, Maximum Seating Height:19".The Seat & back are

Back Chair made up of 12mm thk hot pressed plywood upholstered with PVC with polyurethane foam, chair seat

has foam of density 32-35 kg/m3. The backrest has a foam of 28kg/m3.

Digitally signed by AMIT

Sno. Item Specifications Unit Qty Rate Amount

Supplying and placing in position of main table as per photograph/drawing .The table shall be made out

of 25mm thick pre -laminated particle board of approved shade. The working and non working edges

shall be finished with machine pressed with 2mm PVC egdge banding. The table top shall be supported

with MS powder coated "C" shape leg of size 50mm x 50mm with connectors of size 40mm x 40mm.

The front modesty are made out of 18mm thick prelaminated particle board with 2mm thk pvc edge

banding. The table shall be provisioned with Side unit of overall size: 900mm(L) x 450mm(D) x

BO Incharge 675mm(H) . Side storage having a provision for three equal drawer unit and two openable shutter &

Table one open storage with shelf in it. The Side unit top shall be made out of 18mm thick pre laminated

particle board and rest all storage to be made out of 18mm thick pre laminated particle board.

Provision of Junction box, wire raceway and 6 module fliptop box for wire passing or as per site

requirement.Main Table Dimension (L)2100mm X (D) 900mm X (H)750mm overall Side Runer

Dimension (L)900mm X (D) 400mm X (H) 675mm

Supplying and placing in position of Back Storage as per photograph/drawing .The back storage shall

be made out of 25mm thick pre -laminated particle board of approved shade. The working and non

11 Back Storage working edges shall be finished with machine pressed with 2mm PVC egdge banding. Back Storage Nos 2.00 23,500 47,000.00

Dimension (L)2100mm X (D) 400mm X (H)675mm

Supplying and placing in position of conference table of required size as per image/ Layout drawing.

The work surface top should be of thickness 42mm top prelaminated particle board with 2mm thick

Conference PVC edge banding. The side panel are made up of 36mm thick prelaminated particle & modesty panel

12 are made out of 25mm thick prelaminated particle board with 2mm thick PVC edge banding. The wire Nos 1.00 48,500 48,500.00

carrier should be made from 0.6mm thick CRCA & powder coated 40-50 microns. Also having a

provision of 6 module flip top box & metal raceway for wire flow.

Supplying and placing in position of 360 degrees revolving medium back chair . The Craze chair of Size

:-(W)590mm X (D)505mm X (H)1005mm - 1115mm. The chair shall be ergonomically design contour

lumbar back design made of 12mm thick BWR plywood (IS Grade - 303 for seat and back) upholstered

Medium Back with leatheritte and cut foam. The chair shall be provided with pneumatic height adjustment which

13 chair Confrence shall have stroke of 10.0 +/- Nos 9.00 9,500 85,500.00

room 0.3 cm . Five star chrome base with nylon castors . Chair seat has foam of density 30-35 (+/- 2kg

/m3) The backrest has a foam of 28kg/m3.

Dimension: 1200mm(L) X 600mm(D) x 1050mm(H) Supplying, and placing in position of linear

workstation as per Image.The worktop made out of 25mm thk. Prelam Particle board with 2 mm thk

PVC edge banding.The Table top supported on Mild Steel of size 50mm x50mm Slanted Leg and 50mm

x 25mm Horizontal connectors with Powder coting of 50 Micron.Middle Leg :- 0.8 mm thk Metal panel

fixed on both side of the "T" leg for Vertical wire carrying purpose.(Sharing Workstation). 0.8 mm thk

Single/Double metal powder coated raceway with Powder coting of 50 Micron below top for

Linear wiring.Vertical wire carrying pole with powder coating 50 micron below top for wiring( Non- sharing

14 workstation ). Also having a provision of ms perfoated sheet hanging modesty. provision of glass Nos 6.00 24,500 147,000.00

divider rest on the "D" brackets on the table top between opposite seatings. All working or non working

edges shall be provided with machine pressed 2mm thick PVC edging using special hot melt glue at hot

temperature. Provision of pullout PVC keyboard tray and CPU trolley for each seating.

Also a provision of Pedestal Unit (size:- L-400mm x D-450mm x H-600mm) with a combination of 2

drawer & one filing drawer. The pedestal storage unit shall be made of 18 mm thick prelaminated

Particle board with provision of handles & Locking arrangement

Digitally signed by AMIT

Sno. Item Specifications Unit Qty Rate Amount

Supplying and placing in position of main table as per photograph/drawing .The table shall be made out

of 25mm thick pre -laminated particle board of approved shade. The working and non working edges

shall be finished with machine pressed with 2mm PVC egdge banding. The table top shall be supported

with MS powder coated "C" shape leg of size 50mm x 50mm with connectors of size 40mm x 40mm.

The front modesty are made out of 18mm thick prelaminated particle board with 2mm thk pvc edge

banding. The table shall be provisioned with Side unit of overall size: 900mm(L) x 450mm(D) x

BO Incharge 675mm(H) . Side storage having a provision for three equal drawer unit and two openable shutter &

Table one open storage with shelf in it. The Side unit top shall be made out of 18mm thick pre laminated

particle board and rest all storage to be made out of 18mm thick pre laminated particle board.

Provision of Junction box, wire raceway and 6 module fliptop box for wire passing or as per site

requirement.Main Table Dimension (L)2100mm X (D) 900mm X (H)750mm overall Side Runer

Dimension (L)900mm X (D) 400mm X (H) 675mm

Providing and fixing printer table of size 1500 mm × 750 mm (5' × 2.5') made from 18 mm thick pre-

laminated particle board (both side laminated) of approved shade and make, including top, sides,

modesty panel, shelves as required, edge banding with 2 mm PVC edge tape on exposed edges,

15 Printer Table necessary screws, fittings, hardware, level adjustment arrangement, labour, handling, transportation Nos 1.00 11,500 11,500.00

and complete installation as per approved design and direction of Engineer-in-Charge.

Dimesnion: 1500mm(L) x 1500mm(L) x 600mm(D) x 1200mm(H) Modular Workstation With Side Top

with 3 drawer Pedestal Size 1500W x 600D x 750/1200H.Partition NI-60mm Partition Ht.

1200mm, Double Raceway systems Skirting label and below the table top . lower tile both side

laminated and upper tile inside side fabric, White Board and white Tinted Glass . With Side Top Size

16 900W x 400D x 750H 25mm thick Gabel end 18mm thick MDF board., and 3Drawer top supported Nos 7.00 38,000 266,000.00

Pedestal unit Size 400W x 400D x 725H made in 18mm thick..Complete Made in MDF Board..

Laminate 1- Frosty White, Laminate2 For drawer Facia-Honkong Blue, Fabric-F 161 Dolphin Blue,

Powder Coating- Munshel Gray. and White Tinted Glass

Supplying and placing in position of 360 degrees revolving medium back chair . The Craze chair of Size

:-(W)590mm X (D)505mm X (H)1005mm - 1115mm. The chair shall be ergonomically design contour

lumbar back design made of 12mm thick BWR plywood (IS Grade - 303 for seat and back) upholstered

with leatheritte and cut foam. The chair shall be provided with pneumatic height adjustment which

Reception/ shall have stroke of 10.0 +/- 0.3 cm . Five star chrome base with nylon castors . Chair seat has foam

Meeting room of density 30-35 (+/- 2kg /m3) The backrest has a foam of 28kg/m3.

Providing & Installation of Pantry table of size 1.2m x 0.75m x 1.05m (ht) made out of 19mm thk.

Commercial Board finished in Recon veneer and DU Pont Coreanof approved shade as per design. The

Recon surfaces to be white Duco painted. A glass top od width 0.2m on SS pegs to be provided above

18 Pantry Table Nos 1.00 24,500 24,500.00

table. One (1) number Drawer pedestal with 3 drawers to be provided under the table.

Providing & Installation of Reception table of size .75Dia X 0.75m (ht) made out of 19mm thk.

Commercial Board finished in Recon veneer and DU Pont Coreanof approved shade as per design. The

Recon surfaces to be white Duco painted. A glass top od width 0.2m on SS pegs to be provided above

19 Reception Table Nos 1.00 26,500 26,500.00

table. One (1) number Drawer pedestal with 3 drawers to be provided under the table.

Digitally signed by AMIT

Sno. Item Specifications Unit Qty Rate Amount

Supplying and placing in position of main table as per photograph/drawing .The table shall be made out

of 25mm thick pre -laminated particle board of approved shade. The working and non working edges

shall be finished with machine pressed with 2mm PVC egdge banding. The table top shall be supported

with MS powder coated "C" shape leg of size 50mm x 50mm with connectors of size 40mm x 40mm.

The front modesty are made out of 18mm thick prelaminated particle board with 2mm thk pvc edge

banding. The table shall be provisioned with Side unit of overall size: 900mm(L) x 450mm(D) x

BO Incharge 675mm(H) . Side storage having a provision for three equal drawer unit and two openable shutter &

Table one open storage with shelf in it. The Side unit top shall be made out of 18mm thick pre laminated

particle board and rest all storage to be made out of 18mm thick pre laminated particle board.

Provision of Junction box, wire raceway and 6 module fliptop box for wire passing or as per site

requirement.Main Table Dimension (L)2100mm X (D) 900mm X (H)750mm overall Side Runer

Dimension (L)900mm X (D) 400mm X (H) 675mm

Providing & Installation of Pantry chairs of required dimension and as per instruction of EIC

20 Pantry chairs Nos 6.00 3,700 22,200.00

The storage top 25 mm thick, shutter and side panels are made of 18mm thick and back panel is made

of 09mm thick MDF of approved shade. All the edges of storage surface shall be provided with machine

Openable pressed imported PVC lipping glued with hot melt EVA glue free from any VOC with free groove handle

Shutter storage and suitable lock. All exposed area PVC edge lipping

Pantry Under Counter Storage, made with HDHMR board finished with laminate on all exposed

Pantry Under surfaces. Unit depth: 600mm. All edges shall be finished with matching edge banding. Includes

22 Counter shutters, shelves, hardware (hinges, handles), and necessary fittings complete in all respects. Sqm 2.00 11,500.00 23000

Pantry Overhead Storage Unit, made from HDHMR board of approved shade and grade conforming to

E1 norms, with unit depth of 400mm. All exposed edges finished with 2mm PVC edge banding using

23 hotmelt EVA glue. Includes shutters, shelves, and necessary hardware and fittings, complete in all Sqm 2.00 10,500.00 21000

3 Drawer top supported pedestal unit size 400W X 400D X 725 H made in 18mm thick complete made

24 Mobile Vanity Nos 3.00 8,800.00 26400

Digitally signed by AMIT

S.No 2025 E & Description Unit Qty. Rate Amount (A)

LED Down lighter (SMD Type) (System lumen efficacy ≥ 105 < 120 lm/Watt ) Supplying,

Installation, Testing & Commissioning of LED Recessed/ surface Down lighter (Round/

square/ Rectangular) SMD type of following body material with PMMA and prismatic

diffuser and construction as per IS : 10322 with driver as per the requirement with Driver

efficiency >85%, Operating voltage AC 140-270 Volt, frequency 50/60 hz, Operating temp

range -50C to 400C, internal surge protection of 2.5 KV with Short & Open circuit protection

,THD < 10% , P. F.≥0.95, IP20, CRI >80, UGR (Unified Glare Rating) < 19, Flicker free (flicker

should be below 5%), life time (LED, Driver & electrical circuitry), of minimum 50000 Burning

Hours with 70% of initial Lumen maintained till life ends, CCT 3000°K /4000°K / 5700°K /

6500°K (As per ANSI Bin), SDCM (Standard Deviation Colour Matching) <3, Maximum

power consumption should not more than the specified rating and Fixture shall be

confirming to relevant BIS standards. Manufactures Word Mark/ Name Engraved/

Embossing/ Screen printing on housing Complete in all respect i/c external connections

with 1.5 sq.mm FRLS/HFFR, PVC insulated copper conductor single core cable and

earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy ≥105

and <120 lm/Watt output . LM79 & LM80 Test report and all testing required for LED fixtures

as per BIS shall be submitted. Shape size and CCT shall be as approved by Engineer-in-

Charge as per requirement. (Thermal management: heat sink of aluminium housing such

that LED junction temperature shall not rise above 90°C) Powder coated die cast

/Extruded aluminium Body including trim

Digitally signed by AMIT

S.No 2025 E & Description Unit Qty. Rate Amount (A)

LED Panel light 2x2 ft., (System lumen efficacy >135 lm/Watt) Supplying, installation, Testing

& Commissioning of Panel light 2x2 ft., of following body material and construction as per

IS : 10322 with driver as per the requirement with Driver efficiency >85%, Operating voltage

AC 140-270 Volt, frequency 50/60 hz, Operating temp range -5 0C to 40 0C, internal surge

protection of 2.5 KV with Short & Open circuit protection, THD < 10% , P. F.≥0.95, IP20, CRI

>80, UGR (Unified Glare Rating) < 19, Flicker free, (flicker should be below 5 %), life time

(LED, Driver & electrical circuitry), of minimum 50000 Burning Hours with , 70% of initial

Lumen maintained till life ends ,CCT 3000°K / 4000°K / 5700°K /6500°K (As per ANSI Bin),

SDCM(Standard Deviation Colour Matching) <3, Maximum power consumption should not

more than the specified rating and Fixture shall be of relevant BIS standard. Manufactures

Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. complete in all

respect i/c external connections with 1.5 sq.mm FRLS/HFFR, PVC insulated copper

conductor single core cable and earthing etc. as required with Minimum 5 year OEM

warranty. System lumen efficacy >135 lm/Watt output . LM79 & LM80 Test report and all

testing required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be

as approved by Engineer-inCharge as per requirement. (Thermal management: heat sink

of aluminium housing such that LED junction temperature shall not rise above 90°C).

Powder coated die cast /Extruded aluminium Body (Thickness > 1.20 mm)

Total of Electrical items 149940.00

Digitally signed by AMIT