REPAIR TO SHEET, POST OF SHEDS, FLOORING, DADO, SKIRTING TILE AND CERTAIN OTHER MISC B/R WORKS IN TECH AREA AT AF STN UTARLAI

Amount

S & F Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws including dismantling of old sheeting complete all as specified and directed.

S & F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws including dismantling of old sheeting complete all as specified and directed.

S & F Hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 and including dismantling Complete all as specified and directed

S&F Rolled sections as in main and cross beams, hip and jack rafters purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates Fe-410- W(Gde- E-250) quality- B, and including dismantling, Complete all as specified and directed

M & L for preparation of new steel surfaces of any description, exc 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified.

M & L for preparation of new steel surfaces of any description, n.exc 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified.

Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) as in Roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work , Complete all as specified and directed.

M&L for reinforced cement concrete design mix M-25 (20mm graded aggregates) in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like, complete all as specified and directed.

M&L for formwork to (rough finished flat surfaces of concrete ) soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping). complete all as specified and directed.

M&L for formwork to (rough finished flat surfaces of concrete ) edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide . complete all as specified and directed.

M & L for ms deformed or twisted ,TMT bars 10 mm dia and above , cut to length, bent to shape required, including cranking, bending spirally for hooping, hooking ends and binding with MS wire (annealed) not less than 0.90 mm dia or securing with clips quality conforming to Fe-410-S or Fe-410 -0 ,complete all as specified and as directed.

M & L for 10 mm thick rendering in CM 1:3, finished even and smooth as in ceiling including applying three coats of white wash complete all as specified and directed.

Demolition of cement Concrete of any description and in any position not otherwise specifically provided for, complete all as specified and directed.

M & L PCC1:2:4 type B-1 (using 20 mm graded stone aggregate) as in coping or similar work etc including necessary form work complete all as specified and directed.

M&L for applying roof treatment with 3mm thick APP modified membrane with non woven polyster reinforcement over screed bedding of 10mm thick in CM 1:6 on roof slab over 25mm thick plain cement concrete type B-0 using 12.5mm graded stone aggregate as is roof padding, the membrane shall be laid by torch application method with overlap of 100mm on either side along with a coat of bituminous oil based primer @250gm/sqm weight not less than 3kg/sqm alongwith taking down of old roof treatment complete all as specified and directed.

Taking down cement plaster on brick/ concrete or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc including 15 mm thick rendering with cement mortar 1:6 finished even and smooth with out using extra cement and applying three coats of white wash , complete all as specified and directed

Supply only Integral water proofing compound complete all as specified and directed.

M&L for non Skid ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 but not exceeding 0.18 sqm, in floors and set and jointed in neat cement slurry and pointed in white or coloured cement to match etc. and including 15mm thick screed bed in CM 1:6 complete including dismantling of old tiling all as specified and directed

M&L for glazed ceramic coloured joint free tiles of size (450x300 mm) x 7mm thick in dados skirting etc set and jointed in neat cement slurry and pointed in white or coloured cement to match and including 10mm thick plaster in CM 1:4 complete including dismantling of old tiling all as specified and directed

M&L for Gypsum board false ceiling: fabrication and fixing in position of false ceiling at a ht of 3-4 mtr from floor level by fixing 12mm thick gypsum board sheets on frame work of GI sheet section . The main runner of 22 guage GI Sheet and cross runner of 24 guage . GI sheet must be framed to form a mesh of 2 feet x 2 feet c/c. The gypsum board must be fixed to the GI frame and joint to be properly filled in with pop paste and paper tape to get a levelled smooth ceiling. Recessing of the gypsum board for light fixtures must be done along with extra form of GI sheet section of hold the concealed light fixtures etc. including two or more coats to given even shade of plastic emulsion paint on ceiling with putty work complete with designer ceiling (with part ply laminate and cover) including dismantling of old false ceiling as required & directed by Engr-in-Charge.

S&F Anodised aluminium snap grid of size 605 x 605mm frame work for false ceiling including S&F 12 mm thick Perforated particle board/ tiles for insula-tion and accoustic purposes, 60x60 cm in size, fixed with nails to timber framework or with staples or on snap grid as in ceiling alongwith dismantling of old wall and ceiling boards complete all as specified and as directed.

Demolition of pre-cast PCC block walling / brick work or stone / boulder masonry including all quoins, arches, pillars, etc. built in cement mortar or cement lime mortar complete all as specified and directed

M&L for stone walling of squared rubble, regular coursed, well bonded, bedded and solidly hearted,built in cement mortar 1: 6 and including complete all as specified and directed

M&L for Rendering 15mm thick in cement mortar (1:4) on brick walls or concrete/stone walling surfaces, finished even and smooth without using extra cement and applying applying two coats of cement base paint over a coat of primer , complete all as specified and directed.

M&L for 15 mm thick rendering on fair faces of brick work or concrete surfaces with cement mortar 1:6 finished even and smooth with out using extra cement and applying three coats of white wash complete all as specified and directed.

Demolition of cement concrete ( unreinforced) ) in ground floors and pavings n exc 15 cm thickness (below or above ground level) , Complete all as specified and directed.

M & L for cement concrete 1:4:8 type D2 using (40mm graded stone aggregate) as in sub base floor concrete complete all as specified

M & L for 40 mm thick cement concrete 1:2:4 type B 0 using (12.5 mm graded stone aggregate) as in floor finish even and smooth with out using extra cement, concrete complete all as specified

M/S Tanisha Traders (BID ID -3134819)

M/s Malinath Electricals (BID ID -3129754)