PROVN OF TOILET BLOCK AND BATHROOM FOR OR LIVING ACCN AND OTHER SANCTIONED WORKS AT CHANGSARI MILITARY STATION UNDER GE RANGIA

Amount

Excavation in trenches n.exc 1.5m wide and n.exc 1.5 m in depth for foundation etc or for shafts, wells, cesspits, manholes, pier holes etc n.exc 10 sqm on plan and n.exc 1.5m in depth and getting out in soft/loose soil complete all as per specified and as directed by Engineer-in-charge.

Excavation in trenches for each additional 1.5 m or part thereof in depth beyond the first 1.5 n exc 3.0 m deep and getting out in soft/loose soil complete all as specified and as directed by Engineer-in-charge.

M&L for PCC 1:3:6 type C-2 (40mm graded stone aggregate) as in foundations, fillings and mass concrete complete all as per specified and as directed by Engineer-in-charge.

M&L for reinforced cement concrete (nominal mix) type B-l, 1:2:4 (20 mm graded aggregate) as in columns, pillars, piers, posts and struts etc, complete all as per specified and as directed by Engineer-in-charge.

M&L for form work for side of concrete footings, foundations beam, base of columns & similar works vertical or batter complete all as specified and as directed by Engineer-in-charge.

M&L for Formwork to faces of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses, etc.; vertical or to batter, complete all as specified and as directed by Engineer-in-charge.

M&L for mild steel TMT bars 10 mm dia. and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips, complete all as per specified and as directed by Engineer-in-charge.

S&F 100 mm High density polyethylene pipes (HDPE Pipes PN 10) as in weep holes to walls, complete all as per specified and as directed by Engineer-in-charge.

Returning, filling in, including spreading, leveling, watering and well ramming in layers n exc 25cm complete all as per specified and as directed by Engineer-in-charge.

Removing excavated material not exc. 50 m & depositing where directed at a level not exc. 1.5 m above starting point complete all as per specified and as directed by Engineer-in-charge.

Surface excavation n.exc 30cm deep and averaging 15cm deep and getting out in soft/loose soil complete all as per specified and as directed by Engineer-in-charge.

M&L for Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering, complete all as per specified and as directed by Engineer-in-charge.

M&L for Hardcore of guage exc 63mm but n exc. 100 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rolled/rammed to a true surface, complete all as per specified and as directed by Engineer-in-charge.

M&L 100 mm thick PCC (1:2:4) type B-1 (using 20 mm graded crushed stone aggregate) as in floor, finished even and smooth without using extra cement complete all as specified and as directed by Engineer-in-charge.

M&L for forming construction joint 30 mm deep x 10 mm wide filled with sealing compound grade "A", complete all as specified and as directed by Engineer-in-charge.

M&L for Painting lines, dashes, arrows, letters, etc. on roads pavements and the like n exc 10cm wide with road marking paint, white or golden yellow, complete all as specified and as directed by Engineer-in-charge.

Surface dressing not exc. 15 cm deep in soft/loose soil, complete all as per specified and as directed by Engineer-in-charge.

Rough excavation in soft/loose soil and getting out for shallow pit n. exc 1.5 m deep, complete all as specified and as directed by Engineer-in-charge.

M&L for PCC (1:4:8) type D2 ( using 40mm graded crushed stone aggregate) as in foundation, filling and mass concrete complete all as per specified and as directed by Engineer-in-charge.

M&L for brick work with sub class 'B' bricks, straight or curved on plan exc. 6m mean radius in cement mortar 1:6, complete all as per specified and as directed by Engineer-in-charge.

'M&L for sand filling under floors or in foundations spreading and levelling in layers not exc. 25 cm thick including watering and consolidation, complete all as per specified and as directed by Engineer-in-charge.

M&L for rendering 15mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 , surface finished even and smooth without using extra cement using water proofing compound in top layers as per manufacturer's direction complete all as per specified and as directed by Engineer-in-charge. Note - WPC shall be measured and paid saparately.

Supply only integral water proofing compound confirming to IS complete all as per specified and as directed by Engineer-in-charge.

M&L 15mm thick rendering in CM (1:6) on other than fair faces of brick work or concrete surfaces and finished the surface even & smooth without using extra cement complete all as per specified and as directed by Engineer-in-charge.

M&L for preparing new plastered surfaces and applying two coats of cement base paint on one coat of white wash on surfaces of walls, complete all as specified and as directed by Engineer-in-charge.

M&L for preparing newly plastered surfaces of walls and applying three coats of white wash complete all as specified and as directed by Engineer-in-charge.

M&L for hardcore of guage not exc. 63mm deposited, spread and levelled in layers not exc. 15 cm thick, watered and rammed to a true surface of broken stone or boulders, complete all as per specified and as directed by Engineer-in-charge.

M&L for 75 mm thick cement concrete type D-2, 1:4:8 (using 40 mm graded stone aggregate) as in sub base, complete all as specified and as directed by Engineer-in-charge.

M&L 75 mm thick Cement concrete type C-2, 1:3:6 (using 40 mm graded stone aggregate) as in footpath / hardstanding / pavings / plinth protections, finished even and smooth without using extra cement complete all as specified and as directed by Engineer-in-charge.

S&F coloured non-skid ceramic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shades of tiles over 15 mm thick screed bed or bedding layers in CM 1:6 complete all as per specified and as directed by Engineer-in-charge.

M&L for Coloured Glazed ceramic tiles 300 x 450 x 7 or 8 mm thick, on vertical surfaces such as skirting, dados and risers to steps etc., set and jointed in neat cement slurry and pointed in white or Coloured cement to match over and including 15 mm thick screed in CM (1:6) complete all as per specified and as directed by Engineer-in-charge.

S&F anodised aluminium window and ventilator shutters, fixed type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings, screws etc complete all as specified and directed by Engineer-in-charge.

S&F 4 mm thick Figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sq. m in each pane, complete all as per specified and as directed by Engineer-in-charge.

S&F galvanised mild steel wire cloth, 0.56 mm dia of wire and average width of aperture 1.18 mm and fixed with galvanised wire staples, complete all as specified and as directed by Engineer-in-charge.

M&L Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping), complete all as per specified and as directed by Engineer-in-charge.

M&L for Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC / PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide, complete all as per specified and as directed by Engineer-in-charge.

M&L for mild steel TMT bars 8 mm to 10 mm dia., cut to length, bent to shape required, in stirrups, spacers and binders and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips quality confirming to Fe-410-S 0r Fe-410-O, complete all as per specified and as directed by Engineer-in-charge.

M&L for RCC (desing mix) M-25 (20 mm graded Agg) as in foundations, including rafts, footing, foundation beams, plinth beams, base of columns etc., complete all as per specified and as directed by Engineer-in-charge.

S&F MS steel work in tubular trusses including special shaped washers etc., complete using ERW or induction butt welded tubes confirming to IS 1161- 1979 graded St 240 along with one shop coat of zinc chromate primer paint , complete all as per specified and as directed by Engineer-in-charge.

M&L for preparation of new or previously untreated wood or wood based surfaces of any description, exceeding 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of zink chromate primer, complete all as specified and as directed by Engineer-in-charge.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated or semi-corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 mpa as in roof covering/cladding to wall, fixed with self tapping screws or J hooks, complete all as specified and as directed by Engineer-in-charge.

S&F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 mpa as in roof covering/cladding to wall, fixed with self tapping screws or J hooks, complete all as specified and as directed by Engineer-in-charge.

S&F solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet rainforced with MS square tube in opening complete all as per specified and as directed by Engineer-in-charge.

Supply and fixing factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. .frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail,; Paneling of plain colour PVC sheet to be fitted in the M.S. frame welded/ sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement complete all as per specified and as directed by Engineer-in-charge.

M&L for Granite (of any type) work (table rubbed and polished) 20mm thick in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, complete all as specified and as directed by Engineer-in-charge.

M&L precast Coloured cement concrete glossy finished chequered tiles 300x300x25mm thick set jointed and pointed in with grey cement and pigment laid over and including 20mm thick screed bed in CM 1:6 in floorings, complete all as per specified and as directed by Engineer-in-charge.

M&L for PCC (1:2:4) type B-1 ( using 20 mm grade crushed stone aggregate) as in coping roof kerbs or mud stops, rounded or chamfered on edges with necessary form work as required complete all as specified and as directed by Engineer-in-charge.

S&F15 mm bore fancy type Chromium plated bib taps, cast copper alloy, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and as directed by Engineer-in-charge.

S&F fancy type 15mm dia bore pillar tap cast copper alloy with capston heads chroumium plated, screwed down high pressure with or without lettered Hot or Cold with long screwed shanks and fly-nuts, screwed for iron pipe complete all as per specified and as directed by Engineer-in-charge.

S&F 15mm angle stop valves cast copper alloy, fancy type, chromium plated with long shank and cup for iron pipe or for unions complete all as per specified and as directed by Engineer-in-charge.

Supply and fix 100mm dia grating doom of PTMT with minimum weight 25 grams complete all as specified and as directed by Engineer-in-charge.

S&F 15mm dia PVC connection pipe with PTMT nuts of length 450 mm complete all as specified and as directed by Engineer-in-charge.

S&F PVC valveless, syphonic action type 10 ltr capacity low level flushing cistern, white, with inlet, ball valve, float and handle including brackets and 32 mm bore PVC flush pipe, complete all as per specified and as directed by Engineer-in-charge.

S&F Vitreous China Ware Wash hand basin white, flat back, size 550 x 400 mm size (flat back or angle back type) including cutting for and pinning ends of brackets or erecting stand etc., complete all as per specified and as directed by Engineer-in-charge.

S&F vitreous china wash down water closet pan (pedestal pattern) white, including seat cover, closed pattern with flat bottom and cover with chromium plated hinging device complete all as per specified and as directed by Engineer-in-charge.

S&F Vitreous China squatting pan "Orissa" patern size 580x440mm white with integral foot rest including connection to trap and to flushing pipe, anti-syphonage pipe, etc including 'P' or 'S' trap complete all as per specified and as directed by Engineer-in-charge.

S&F Vitreous china urinals, half stall type white complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement complete all as per specified and as directed by Engineer-in-charge.

S&F swivel shower of PTMT any colour for fixing with 15mm pipe. (Minimum weight 40gms), complete all as specified and as directed by Engineer-in-charge.

S&F cromimum plated health faucet (Easy flex Chrome Hose, Handset, ABS Body & Bracket) shower with CP flexible pipe up 15 mm bore with 1 m long Easy Flex tube in chrome finish, complete all as per specified and as directed by Engineer-in-charge.

S&F corner glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chomium plated bracket guard & railing 45 cm long, complete all as per specified and as directed by Engineer-in-charge.

S & F Brass Chromium plated tubular towel rail, 20 mm dia., D Type, 60 cm long between flanges complete all as per specified and as directed by Engineer-in-charge.

S&F 50 mm dia low density polyethylene pipe (LDPE) of pressure rating @ 6Kgf per sqcm fixed to wall complete all as specified and as directed by Engineer-in-charge.

S&F 50 mm PVC (SWR) floor trap with grating including jointing with solvent cement complete all as per specified and as directed by Engineer-in-charge.

S&F 110 mm dia PVC (SWR) pipes single socketed, in any length, laid in trenches or in floors, complete all as per specified and as directed by Engineer-in-charge.

S&F110 mm dia bore PVC (SWR) bends with acess door, complete all as specified and as directed by Engineer-in-charge.

S&F PVC SWR vent cowl 110 mm bore complete all as specified and as directed by Engineer-in-charge.

S&F rotational moulded polyethylene water storage tanks (cylinderical, vertical with closed top) of 1000 Ltrs capacity hoisted and fixed in position including 20mm ball valves, high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed (Minium weight 20mm- 210 gms) and fixed in position complete all as per specified and as directed by Engineer-in-charge.

S & F 20 mm stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed, complete all as per specified and as directed by Engineer-in-charge.

S&F GI tube 15 mm bore medium grade with fittings and fixed complete to wall, ceiling or laid in floor complete all as specified and as directed by Engineer-in-charge.

S&F GI tube 20 mm bore medium grade with fittings and fixed complete to wall, ceiling or laid in floor complete all as specified and as directed by Engineer-in-charge.

S&F 150 mm long extruded Aluminium alloy handles, fabricated type, anodised, complete all as per specified and as directed by Engineer-in-charge.

S&F 150 mm long Aluminium, anodised, barrel tower bolts of extruded section, complete all as per specified and as directed by Engineer-in-charge.

S&F 100 mm long extruded Aluminium alloy anodised butt hinges with galvanized mild steel hinge pin type B-21, complete all as per specified and as directed by Engineer-in-charge.

S&F aluminium alloy 300 mm anodised sliding door bolts with hasp, staple (bolt type) & fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast - aluminium alloy, complete all as specified and as directed by Engineer-in-charge.

M&L for preparing new plastered surfaces and applying two coats of oil bound distemper on walls over 1 mm thick wall care on plastered surface, complete all as per specified and as directed by Engineer-in-charge.

M&L for vitrified ceramic tiles 10 mm thick of light shade (square/rectangular) polished area of each tile not exceeding 0.36 sqm in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shades of tiles over 15 mm thick screed bed or bedding layers in CM 1:4 complete all as per specified and as directed by Engineer-in-charge.

S&F Solid PVC Door Frame of size 50mm x 120mm made out of 5mm Plain colour PVC sheet reinforced with M.S. tube, suppling & fixing in opening as per specification & drawing complete all as per specified and as directed by Engineer-in-charge.

Supply and fixing factory made solid panel factory made solid PVC moulded door shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing complete all as per specified and as directed by Engineer-in-charge.

S&F 4 mm thick sheet glass of ordinary quality in squares not exc. 0.5 sqm in each pane glazing with oil putty complete all as per specified and as directed by Engineer-in-charge.

S&F aluminium frame for doors, partition with shutter (double/single leaf) with one or more rebates using aluminium section of approved make including joining cleat for fixing, handles, glazing/panelling boards etc., complete all as specified and as directed by Engineer-in-charge. Note- Floor spring/door spring closer, glazing and panelling shall be measured and paid separatly

S&F 12 mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work, complete all as per specified and as directed by Engineer-in-charge.

M&L aluminium alloy extruded body Door closer hydraulically regulated, designation No. 1 universal type, suitable for door shutters up to 700 mm in width and of weight not more than 35 kg and fixed complete all as per specified and as directed by Engineer-in-charge.

S&F exposed GI powder coated snap grid frame work for false ceiling of grid size 600x600mm comprising of wall/cleat angle of size 25x25x0.35mm and cross tee of size 22x35x0.60mm with 4mm dia GI wire as suspender and including 4mm thick E-Board classic (decorative type) including fixing arrangement from steel truss of any type and applying three coats of white wash on exposed surface, complete all as per specified and as directed by Engineer-in-charge.

S&F sinks made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar 1:4 to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420 mm bowl size 410 mm x 330 mm x 160 mm, complete all as per specified and as directed by Engineer-in-charge.

S&F glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chomium plated bracket guard & railing 60 cm long, complete all as per specified and as directed by Engineer-in-charge.

S&F CP toilet paper roll holder with flap including all necessary fittings, complete all as per specified and as directed by Engineer-in-charge.

S&F CP towel-ring sqaure, complete all as per specified and as directed by Engineer-in-charge.

S&F of 150 mm internal diameter of double wall corrugated (DWC) high density polyethelene pipes (HDPE) and stiffness classes-8 (SN-8) with ISI marked (with CML no) with and including all fitting & jointing material for sewage line and laid in trenches as specified in IS 16098-2013 part-2 complete all as per specified and as directed by Engineer-in-charge.

Cutting existing 40 or 50 mm bore steel tubing for alterations or additions (each cut measured) complete all as per specified and as directed by Engineer-in-charge.

Supply and laying PP-R Pipes 25 mm dia ( PN 16/ SDR 7.4) with all fittings laid in trenches including testing complete all as per specified and as directed by Engineer-in-charge.

Supply and laying PP-R Pipes 35 mm dia ( PN 16/ SDR 7.4) with all fittings laid in trenches including testing complete all as per specified and as directed by Engineer-in-charge.

S&F gun metal globe or gate valve, with iron wheel head screwed both ends for iron pipe of 25 mm bore, complete all as specified and as directed by Engineer-in-charge.

M&L for rendering 15mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 , surface finished even and smooth without using extra cement, complete all as per specified and as directed by Engineer-in-charge.

S&F 100 mm long extruded Aluminium alloy anodised butt hinges with galvanized mild steel hinge pin type C-21, complete all as per specified and as directed by Engineer-in-charge.

S&F 32 mm bore waste coupling of PTMT (60 gm weight) (half or full threaded), complete all as per specified and as directed by Engineer-in-charge.

S&F 32 mm dia low density polyethylene pipe (LDPE) of pressure rating @ 6Kgf per sqcm fixed to wall complete all as specified and as directed by Engineer-in-charge.

Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required for pipe of internal dia. 100mm, complete all as specified and as directed by Engineer-in-Charge.

M&L for point wiring with 1.5 sqmm size (nominal area) PVC insulated unsheathed single core multi stranded FRLSH copper conductor cable drawn into and incl PVC casing capping sleeves and caps of adequate width and length with all accessories and fittings like bends . elbow crosses etc with PVC round block and PVC terminal boxes with 3.00mm thick plastic laminated sheet cover for mounting fittings etc like switches sockets and fan regulator incl 1.5 sqmm size PVC insulated multistranded FRLSH copper conductor cable as earth continuity conductor and connected to earth dolly complete all as specified and as directed for one light point controlled by one switch, complete all as per specified and as directed by Engineer-in-Charge.

All as per serial item No. 99 above but for one ceiling fan point controlled by one switch.

All as per serial item No. 99 above but for one exhaust fan point controlled by one switch.

All as per serial item No. 99 above but for one 3 pin 5 Amps socket outlet on independent board.

All as per serial item No. 99 above but for one 3 pin 5 Amps socket outlet on same board.

All as per serial item No. 99 above but with 4 sqmm (nominal area) cable with 4.00 sq mm size copper earth continuity conductor of green colour for 15 A socket outlet on independent boards.

Supply and fix switch piano flush type, 6/5 Amps 240 volts single pole one way, complete all as specified and as directed by Engineer-in-charge.

Supply and fix ceiling rose surface backelite three terminals, PVC/polycarbonate, insulated body, complete all as specified and as directed by Engineer-in-charge.

Supply and fix switch socket combination multipurpose 3 pin 15 Amp and 3 pin 5 amp flush type 2 in 1 complete all as specified and as directed by Engineer-in-charge.

Supply and fix switch socket combination multi purpose 3 pin 5 Amp flush type complete all as specified and as directed by Engineer-in-charge.

Supply and fix socket outlet, 5 pin 6 Amps, flush type 2 in 1 complete all as specified and as directed by Engineer-in-charge.

Supply and fix fan regulator electronic type, rotary step, Socket type 240 Volt, complete all as specified and as directed by Engineer-in-charge.

Supply and fix LED tube light fittings with regal batten for LED, wall mounted, extruded head dissipation & integrated with crystal gladd LED tube light (single side connection) 20 W LED 4', 230 V complete with all accessories internally prewired and including connecting up with twin core twisted flexible copper conductor cable from ceiling rose to tube light fitting complete all as specified and as directed by Engineer-in-charge.

S&F LED light fitting 1x9W /1X10W bulk head luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed by Engineer-in-charge.

S&F PVC rectangular block for mounting, DBs, etc. with 3mm thick plastic laminated sheet cover of size 300 x 300 x 50 mm deep complete all as specified and as directed by Engineer-in-charge.

Supply and fix sheet metal enclosure powder painted for MCB SPN 08 way double door DB with din rail and suitable bus bar complete all as specified and as directed by Engineer-in-charge.

Supply and fix sheet metal enclosure powder painted for MCB SPN 12 way double door DB with din rail and suitable bus bar complete all as specified and as directed by Engineer-in-charge.

Supply and fix MCB SPN 6-32 Amp 10KA braking capacity 230/240 volt AC, complete all as specified and as directed by Engineer-in-charge.

Supply and fix MCB SPN 40 Amp 10KA braking capacity 230/240 volt AC, complete all as specified and as directed by Engineer-in-charge.

Supply and fix MCB SP 240 Volts 6 to 32 Amps breaking capacity 10 KA rating complete all as specified and as directed by Engineer-in-charge.

Supply and fixing 240V, 10 KA 'B' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 6 to 32 AMP, in the MCB DB Complete with connection testing and commissioning, complete all as specified and as directed by Engineer-in-charge.

Supply and fix 6 Sqmm 1100 volts grade heavy duty cable PVC insulated aluminium conductor, served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 metre apart including 4mm suspension wire, one twin core cable flat or circular complete all as specified and as directed by Engineer-in-charge.

Supply and fix exhaust fan heavy duty AC, single phase 230 V of size 300 mm sweep having metallic blade and frame and pre wired with cutting of wall to suitable size to fix the exhaust fan with nut bolts etc., complete all as specified and as directed by Engineer-in-charge.

S&F House service bracket (Hook type) complete with 40 mm dia GI pipe 3.00 m long, medium grade, two Nos. of 90 degree bends, M.S hook and stay or guy complete all as per specified and as directed by Engineer-in-charge.

Supply and fix lamp holder, PVC/Polycarbonate type with LED lamp 10 W, complete all as specified and as directed by Engineer-in-charge.

Supply and fixing LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and as directed by Engineer-in-charge.

Supply and fixing ceiling fan having sweep size of 1400 mm, 240 volt, energy efficient, 50 Hz having metalic blade of 3 nos with inetrnal pre-wired including accessories such as hook, nuts, bolts, etc. complete all as per specified and as directed by Engineer-in-charge.

Supply and fix exhaust fan heavy duty AC, single phase 230 V of size 225 mm sweep having metallic blade and frame and pre wired with cutting of wall to suitable size to fix the exhaust fan with nut bolts etc., complete all as specified and as directed by Engineer-in-charge.

Supply and fix electric water heater, storage type steel body with opper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, hermostate, NRV, connection piece etc., complete all as specified and as directed by Engineer-in-charge.

Supply and install hi wall split units indoor/outdoor complete with cordless remote control unit and with in built air ioniser and Plasma filter for better indoor air quality with minimum 4 star rating and EER 3.2.of capacity 2.0 TR, complete all as specified and as directed by Engineer-in-charge.

S&F 7 KVA capacity of volatge stabilizer for automatic operation, single phase, naturally air cooled indoor type and designed for input voltage variation between 130 V to 300 V, having 4-6 second initial delay with output volatge stabilized at 230V with accuracy of ± 2.5%, complete all as specified and as directed by Engineer-in-charge.

Supply and fix single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 Amps for AC point, complete all as specified and as directed by Engineer-in-charge.

M&L for earthing complete with galvanised steel earth plate electrode of size 600 mm x 600 mm x 6 mm thick buried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of the plate not less than 1.5 mtr below ground level, connected to galvanized earth lead wire 4.00 mm dia by means of bolts nuts check nuts & washers of galvanized iron or steel , procteded by GI pipe 15 mm bore( light grade) and watering pipe 20 mm bore GI pipe (light grade) and chamber of pcc 1:4:8 type D2 using 40 mm graded stone aggregate and coping shall be in PCC 1:3:6 type C1 using 20mm graded stone agg. 50 mm thick cover of RCC 1:2:4 type B1 using 20 mm graded stone agg. reinforced with 8 mm dia MS tor bar @ 80 mm c/c both ways including excvation and earth work and removal of surplus soil complete all as shown in electrical plate no. 3 of SSR PT 1, 1991 with charcoal dust and salt complete and earth lead connected to earthing test point (up to main switches, DBs), complete all as specified & testing on completion. NOTE:- (I) item includes the cost of 7.5 mtr length GI pipe for protection for GI earth wire. (ii) item rates includes the cost of 7.5 mtr earth lead GI earth wire. (iii) PCC pit shall be provided at least 500mm away from the pit and not on the earth pit itself and the extra cost of additional length of watering pipe,bends,elbow etc shall be deemed included in the unit rate.

Supplying and fixing 10 Sqmm, twin core, flat cable 1100 volts grade heavy duty cable PVC insulated aluminium conductor, served with inner sheathing of PVC tape and over all PVC sheathed in service connections suspended by insulating hangers not more than 1 metre apart including 4mm suspension wire, complete all as specified and as directed by Engineer-in-charge.

Supplying and fixing 16 Sqmm, twin core, flat cable 1100 volts grade heavy duty cable PVC insulated aluminium conductor, served with inner sheathing of PVC tape and over all PVC sheathed in service connections suspended by insulating hangers not more than 1 metre apart including 4mm suspension wire, complete all as specified and as directed by Engineer-in-charge.

Supply and fix sheet metal enclosure powder painted for MCB SPN 2 way single door DB with din rail and suitable bus bar complete all as specified and as directed by Engineer-in-charge. Note:- The contract sum shall be calculated by deducting the amount shown in Credit Schedule attached to this tender, from total amount of Schedule 'A'/BOQ.

M/s Nice Traders

OM CONSTRUCTIONS