Construction of State Emergency Operation Centre SEOC and Allied Civil Works in Guwahati Assam under AIRBMP

Amount

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth. 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5m, disposed earth to be levelled and neatly dressed.All kinds of soil

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

Centering and shuttering including strutting, propping etc. and removal of form for: Foundations, footings, bases of columns, etc. for mass concrete

Centering and shuttering including strutting, propping etc. and removal of form for:Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

Centering and shuttering including strutting, propping etc. and removal of form for:Suspended floors, roofs, landings, balconies and access platform

Centering and shuttering including strutting, propping etc. and removal of form for:Lintels, beams, plinth beams, girders, bressumers and cantilevers

Centering and shuttering including strutting, propping etc. and removal of form for:Columns, Pillars, Piers, Abutments, Posts and Struts

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.Thermo-Mechanically Treated bars

Steel reinforcement for R.C.C. work including straightening, cutting,bending, placing in position and binding all complete above plinth level.Thermo-Mechanically Treated bars of grade Fe-500D or more.

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. (Note :- Cement content considered in this item is @ 330 kg/cum. Excess/ less cement used as per design mix is payable/recoverable separately).All works upto plinth level Concrete of M25 grade with minimum cement content of 330 kg /cum

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. (Note :- Cement content considered in this item is @ 330 kg/cum. Excess/ less cement used as per design mix is payable/recoverable separately).All works above plinth level upto floor V level Concrete of M25 grade with minimum cement content of 330 kg /cum

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level.Cement mortar 1:4 (1 cement :4 coarse sand)

Providing and laying autoclaved aerated cement blocks masonry with150mm/230mm/300 mm thick AAC blocks in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-Charge. (The payment of RCC band and reinforcement shall be made for seperately).

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in:Cement mortar 1:6 (1 cement : 6 coarse sand)

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.Granite of any colour and shadeArea of slab over 0.50 sqm

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge.Granite work

Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and finished smooth.Granite Stone of approved shade

12 mm cement plaster of mix :1:4 (1 cement: 4 coarse sand)

15 mm cement plaster on rough side of single or half brick wall of mix:1:4 (1 cement: 4 coarse sand)

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade:New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour.Two coats

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :Two or more coats on new work

With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood)

Applying priming coat:With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/ steel works

Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content. With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre

Boring, providing and installation bored cast-in-situ reinforced cement concrete piles of grade M-25 of specified diameter and length below the pile cap, to carry a safe working load not less than specified,excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and temporary casing of appropriate length for setting out and removal of same and the length of the pile to be embedded in the pile cap etc. by percussion drilling using Direct mud circulation (DMC) or Bailer and chisel technique by tripod and mechanical Winch Machine all complete, including removal of excavated earth with all its lifts and leads (length of pile for payment shall be measured up to bottom of pile cap).Note: Truck Mounted rotary/TMR/Tubewell boring machine shall not be used 500 mm dia piles

Vertical load testing of piles in accordance with IS 2911 (Part IV) including installation of loading platform by Kentledge/Anchor piles method and preparation of pile head or construction of test cap and dismantling of test cap after test etc. complete as per specification & the direction of Engineer in-charge. Note: 1. Initial and Routine Load Test shall not be carried out by Note: 2. Testing agency shall submit the design of loading platform for the approval of Engineer-in-charge.Single pile upto 50 tonne Safe capacity Initial test (Test Load 2.5 times the Safe capacity)

Vertical load testing of piles in accordance with IS 2911 (Part IV) including installation of loading platform by Kentledge/Anchor piles method and preparation of pile head or construction of test cap and dismantling of test cap after test etc. complete as per specification & the direction of Engineer in-charge. Note: 1. Initial and Routine Load Test shall not be carried out by Note: 2. Testing agency shall submit the design of loading platform for the approval of Engineer-in-charge.Single pile upto 50 tonne Safe capacity Routine test (Test Load 1.5 times the Safe capacity)

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre,shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I.wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointingcompound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills,diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks)

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished seamless type tubes

Providing and fixing precoated galvanised iron profile sheets (size,shape and pitch of corrugation as approved by Engineer-in-charge)0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 micronsepoxy primer on both side of the sheet and polyester top coat 15-18microns. Sheet should have protective guard film of 25 micronsminimum to avoid scratches during transportation and should besupplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tappingscrews of size (5.5x 55 mm) with EPDM seal, complete upto anypitch in horizontal/ vertical or curved surfaces, excluding the cost ofpurlins, rafters and trusses and including cutting to size and shapewherever required.

Providing and fixing precoated galvanised steel sheet roofing accessories0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxyprimer on both side of the sheet and polyester top coat 15-18 micronsusing self drilling/ self tapping screws complete : Ridges plain (500 - 600mm)

Providing and fixing precoated galvanised steel sheet roofing accessories0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxyprimer on both side of the sheet and polyester top coat 15-18 micronsusing self drilling/ self tapping screws complete : Gutter (600 mm over all girth)

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge.In cement mortar

Providing and laying damp-proof course 40 mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 12.5 mm nominal size).

Extra for providing and mixing water proofing material in cement concrete work in doses by weight of cement as per manufacturer's specification.

Applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7 kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil.

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters.35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete.

Providing and fixing bright finished brass door latch with necessary screwsetc. complete :300x16x5 mm

Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete :250x10 mm

Providing and fixing bright finished brass handles with screws etc. complete:

Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete.

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete :250x16 mm

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete :250x10 mm

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete :125 mm

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.Twin rubber stopper

Providing and fixing pressed steel door frames conforming to IS: 4351,manufactured from commercial mild steel sheet of 1.60 mm thickness,including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm,pressed mild steel welded or rigidly fixed together by mechanical means,including M.S. pressed butt hinges 2.5 mm thick with mortar guards,lock strike-plate and shock absorbersas specified and applying a coatof approved steel primer after pre-treatment of the surface as directedby Engineer-in-charge: Profile C Fixing with carbon steel galvanised dash fastener of required dia and size (to be paid for separately)

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

Providing and fixing Ist quality ceramic glazed floor tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete, on 20 mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand).Dark shade pigment using ordinary cement

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), including pointing the joints with white cement and matching pigment etc., complete.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete.Size of Tile 600x600 mm

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), including grouting the joint with white cement & matching pigments etc. complete.Size of Tile 600x600 mm

Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earthwith lead upto 50 metres.

Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earthwith lead upto 50 metres.

Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge With material conforming to Grade-III (size range 26.5 mm to 0.075 mm ) having CBR Value-20

Providing and laying 60mm thick faciory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :For fixed portionAnodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15)

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately)Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 5 mm thickness

Providing and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compoundconsisting of applying:(a) after surface preparation, first layer of slurry of cement @0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm.(b) laying second layer of Fibre glass cloth when the first layer is still green. Overlaps of joints of fibre cloth should not be less than 10 cm.(c) third layer of 1.5 mm thickness consisting of slurry of cement @ 1.289 kg/sqm mixed with water proofing cement compound @ 0.670 kg/sqm and coarse sand @ 1.289 kg/sqm. This will be allowed to air cure for 4 hours followed by water curing for 48 hours. The entire treatment will be taken upto 30 cm on parapet wall and tucked into groove in parapet all around.(d) fourth and final layer of brick tiling with cement mortar (which will be paid for separately.For the purpose of measurement the entire treated surface will be measured.

Providing and fixing wall panelling at interior partition walls and columns chowkaths etc for decorative face pelmet upto ceiling level from floor level with 12 mm thick solid plywood board(green/century/archid or equivalent)on one side of the wall and finishing with 1 mm thick laminate (green/century/archid or equivalent)of approved shade and make as per design fixed with necessary adhesive complete as specified and directed by the department

supplying fitting and fixing Partition walls both side made out of 19 mm and 12 mm thick greenply & laminated with 1 mm thick greenlam laminates complete and as directed

supplying fitting and fixing Jhonson Zebra Roller blinds (combi blackout)make and shade design as per choice complete as specified and directed by the department at all levels(CEAPPROVED RATE)

Providing fitting and fixing carpet on floor (plain)with material installation including labour carriage etc as directed and specified

Providing brick soling in foundation and under floor with stone/ best quality picked jhama brick, sand packed and laid to level and in panel after preparing the subgrade as directed including all labour and materials and if necessary dewatering, complete. a) Brick on flat Solling

Providing & fixing Knauf Armstrong Woodworks ChannelledG13 Perforated Wooden Planks of size- 192x2400x15mm using Aluminium Keel and GI framework along with an infill of 16kg density 50mm thick Glasswool to achieve an NRC of 0.8

Providing and fixing MCM modified clay tiles of approved shade and color as per direction of the department with fitting fixing all complete

Providing fitting and fixing roof insulation of AEROLAM XLPE 25 mm one side Alu Foil all complete as directed and specified

Providing and Supplying aluminum extruded tubular sections for Structural Glazing with Mullion size of 131 x 67 x 2.00 mm, Transom size of 81 x 67 x 2 mm, Sash Frame of 60 x 25 x 2 mm) as per the architectural drawings and approved shop drawing and as per grade 6063 T5 or T6 as per BIS 1474 including super durable powder coating of 60-80 micron conforming to AAMA - 2604 of required color and shade as approved with design, fabrication, testing, protection, installing and fixing in position semi (grid) unitized system of structural glazing (with open joints) for linear as well ascurvilinear portions of the building for all heights including: (a) Structural analysis &design and preparation of shop drawings for the specified design loads conforming to IS 875 part Ill, including functional design of the aluminum sections for fixing glazingpanels of various thicknesses, aluminum cleats, sleeves and splice plates etc. gaskets,screws, toggles, nuts, bolts, clamps etc., structural and weather silicone sealants,flashings, fire stop (barrier)-cum-smoke seals, microwave cured EPDM gaskets forwater tightness, pressure equalization & drainage and protection against fire hazard including b) Fabricating and supplying serrated M.S. hot dip galvanized / Aluminium alloy of 6005 T5 brackets of required sizes, sections and profiles etc. to accommodate three Dimensional movement for achieving perfect verticality and fixing structural glazing system rigidly to the RCC/masonry/structural steel frame-work of building structure using stainless steel anchor fasteners (HITLI HST3 M10x130) / bolts, nylon separator to prevent bimetallic contacts with nuts and washers etc. of stainless steel grade 316, of the required capacity and in required numbers. (c) Providing and filling,two part pump filled, structural silicone sealant and one part weather silicone sealant compatible with the structural silicone sealant of required bite size in a clean andcontrolled factory / workshop environment including double sided spacer tape,setting blocks and backer rod, all of approved grade, brand and manufacture, as per the approved sealant design, within and all around the perimeter for holding glass. (d) Providing and fixing in position flashings of solid aluminum sheet 1 mm thick and of sizes, shapes and profiles, as required as per the site conditions, to seal the gap between the building structure and all its interfaces with curtain glazing to make it watertight.e) Providing, assembling and supplying vision glass panels (IGUs) comprising of hermetically-sealed 6-12- 6 mm insulated glass (double glazed) vision panel unitsprocessed by Keshar Safety Glass with logo of keshar, of size and shape as required and specified, comprising of an outer heat strengthened float glass 6mm thick, of approved colour and shade with reflective soft coating on surface #2 of approved colour and shade, an inner Heat strengthened clear float glass 6mm thick, spacer tube 12mm wide, desiccants, including primary seal and secondary seal (structuralsilicone sealant) etc. all complete for the required performances, as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineer-in-Charge. The IGUs shall be assembled in the factory/workshop of the glass processor.(f) Coloured tinted float glass 6mm thick substrate with reflective soft coating on face # 2, + 12mm Airgap + 6mm Heat Strengthened clear Glass of approved make having properties as visible Light transmittance (VLT) of 25 to 35 %, Light reflection internal 10 to 15%, light reflection external 10 to 20 %, shading coefficient (0.25- 0.28) and Uvalue of 3.0 to 3.3 W/m2 degree K etc. The properties of performance glass shall be decided by technical sanctioning authority as per the site requirement

Providing and fitting ozone aluminium bottom profile 75mmx50mm top hand rail 40 mm x 40mm gasket and with all accessories 12 mm toughened glass clear balcony profile railing installation complete

Server room raised flooring WITH UNIFLOOR OR EQUIVALENT

supplying and providing steel fire door with frame vision panellock and all other accessories complete as directed by the department

supplying and providing hilti bolt for fixing furniture and racks to the concrete slab HILTI(HSA-BW (M6-M20))

Providing and fixing white vitreous china extended wall mounting water closet of size 780x370x690 mm of approved shape including providing & fixing white vitreous china cistern with dual flush fitting, of flushing capacity 3 litre/6 litre (adjustable to 4 litre/8 litres), including seat cover, and cistern fittings, nuts, bolts and gasket etc complete.

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps

Providing and fixing white vitreous china battery based infrared sensor operated urinal of approx. size 610 x 390 x 370 mm having pre & post flushing with water (250 ml & 500 ml consumption), having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer-in-charge.

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS: 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : Kitchen sink without drain board 610x510 mm bowl depth 200 mm

Providing and fixing PTMT Bottle Trap for Wash basin and sinkBottle trap 38 mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm from the centre of the waste coupling, 77 mm breadth with 25 mm minimum water seal, weighing not less than 263 gms

Providing and fixing C.P. sink mixer with swinging spout J-pipe. including painting of fittings and brackets, cutting and making good the walls wherever require:

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : Rectangular shape 1500x450 mm

Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete.

Providing and fixing PTMT Waste Coupling for wash basin and sink, of approved quality and colour. Waste coupling 31 mm dia of 79 mm length and 62mm breadth weighing not less than 45 gms

Waste coupling 38 mm dia of 83 mm length and 77mm breadth, weighing not less than 60 gms

Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms.

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms

Providing and fixing PTMT shelf 440 mm long, 124 mm width and 36 mm height of approved quality and colour, weighing not less than 300 gms.

Providing and fixing PTMT 15 mm Urinal spreader size 95x69x100 mm with 1/2" BSP thread and shapes, weighing not less than 60 gms.

Providing and fixing toilet paper holder : C.P. brass

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,havingthermal stability for hot & cold water supply and all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall20 mm nominal dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,havingthermal stability for hot & cold water supply and all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall 25 mm nominal dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,havingthermal stability for hot & cold water supply and all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall 32 mm nominal dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,havingthermal stability for hot & cold water supply and all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall 40 mm nominal dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,havingthermal stability for hot & cold water supply and all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall 50 mm nominal dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work 20 mm nominal dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work 25 mm nominal dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work 32 mm nominal dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work 40 mm nominal dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work 50 mm nominal dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work 65 mm nominal dia Pipes

Providing and fixing brass bib cock of approved quality : 20 mm nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 32 mm nominal bore.

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 40 mm nominal bore.

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 50 mm nominal bore.

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 65 mm nominal bore.

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 20 mm nominal bore (In Shaft)

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 25 mm nominal bore (In Shaft & Terrace Floor )

Providing and fixing gun metal non- return valve of approved quality (screwed end) : Horizontal

Providing and fixing gun metal non- return valve of approved quality (screwed end) : Horizontal

Providing and fixing gun metal non- return valve of approved quality (screwed end) : Horizontal

Providing and fixing gun metal non- return valve of approved quality (screwed end) : Horizontal

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 :15 mm nominal bore

Providing and fixing PTMT Ball cock of approved quality, colour and make complete with Epoxy coated aluminium rod with L.P./ H.P.H.D. plastic ball. 25 mm nominal bore, 152mm long, weighing not less than 440 gms

Providing and fixing PTMT Ball cock of approved quality, colour and make complete with Epoxy coated aluminium rod with L.P./ H.P.H.D. plastic ball. 40 mm nominal bore, 206mm long, weighing not less than 690 gms

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 a) 15 mm nominal bore15mm nominal bore

P & F 15mm C.P. sink mixer with swinging spout J-pipe.

P & F Health Faucet with 1.0 meter long flexible pipe for water closet with C.P. Copper Tube flange of approved make.

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. 40 mm dia nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. 50 mm dia nominal bore

Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete : 25 to 40 mm nominal bore

Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete : 50 to 80 mm nominal bore

Painting G.I. pipes and fittings with two coats of anti-corrosive bitumastic paint of approved quality : 40 mm dia nominal bore

Painting G.I. pipes and fittings with two coats of anti-corrosive bitumastic paint of approved quality : 50 mm dia nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :32 mm nominal bore.

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 40 mm nominal bore.

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 50 mm nominal bore.

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :65 mm nominal bore.

Providing & fixing PVC pipe confirm to IS -4985 and suitable for 6 kg/sqcm. This shall include connection from fixtures to all fittings conforming to IS:7834, supports from wall/ceiling, clamps & hangers cutting & making good the walls & floor where ever required. Jointing shall be done complete with PVC solvent cement. Including 1:2:4 concrete all round the pipe with bedding. Making, cutting & chasing in walls / floor, upto 63 mm dia waste pipes & fittings. Making good the same by using 1:1 Cement mortar. 110 mm dia

Providing & fixing PVC pipe confirm to IS -4985 and suitable for 6 kg/sqcm. This shall include connection from fixtures to all fittings conforming to IS:7834, supports from wall/ceiling, clamps & hangers cutting & making good the walls & floor where ever required. Jointing shall be done complete with PVC solvent cement. Including 1:2:4 concrete all round the pipe with bedding. Making, cutting & chasing in walls / floor, upto 63 mm dia waste pipes & fittings. Making good the same by using 1:1 Cement mortar. 110 mm dia Toilet Indirect waste. 40 mm OD

Providing & fixing PVC pipe confirm to IS -4985 and suitable for 6 kg/sqcm. This shall include connection from fixtures to all fittings conforming to IS:7834, supports from wall/ceiling, clamps & hangers cutting & making good the walls & floor where ever required. Jointing shall be done complete with PVC solvent cement. Including 1:2:4 concrete all round the pipe with bedding. Making, cutting & chasing in walls / floor, upto 63 mm dia waste pipes & fittings. Making good the same by using 1:1 Cement mortar. 110 mm diaToilet Indirect waste. 50 mm OD

Providing & Fixing of PVC injection moulded SWR floor trap inline with top tile & strainer having 50 mm water seal as per IS : 14735, including cost of PVC SWR height raiser to be fixed over floor trap with one inlet of 110 mm. Including cutting & making good the walls & floors. The jointing shall be done with complete with PVC solvent cement. 110 mm inlet & 110 mm outlet

Providing and fixing clean out pipe (door piece) of POLO KAL NG for cleaning. 100 mm OD

Providing and fixing clean out cap plug (FCO ) for cleaning of same material composition as per item no. 1 above 100 mm dia.

Providing, fixing, testing & commissioning of uPVC inlet fitting with maximum 3 inlets 40, 50 & 75 OD size, fixed to uPVC traps including jointing complete with all civil work.

Providing & fixing 4 mm thick stainless steel grating with rim of approved design including setting in floor with cement mortar. (For Trap and Floor Drain) 125 mm dia

Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : All Kind of Soil Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame o f 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: 150 x 100 mm size P type With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 150 mm dia. R.C.C. pipe

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 250 mm dia. R.C.C. pipe

Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg), R.C.C. top slab with 1:2:4 mix (1 cement: 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand), finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design: With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete.

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 110 mm diameter

Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams.

Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer -in-charge, upto 90 metre depth below ground level. All types of soil 300 mm dia

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge. 150 mm nominal size dia

Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge. 150 mm nominal size dia

Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.

Supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in

Supplying, filling, spreading & leveling coarse sand of size range 1.5 mm to 2 mm in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engineer -in-charge.

Gravel packing in tubewell construction in accordance with IS:4097 including provinding gravel fine/medium /coares, in requried grading & sizee as per actual requriment, all complete as per direction of Engineer -in-charge.

Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by “V” notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge.

Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : All Kind of Soil Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 150 mm dia. R.C.C. pipe

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 250 mm dia. R.C.C. pipe

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 300 mm dia. R.C.C. pipe

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Extra for depth beyond 45 cm of brick masonry chamber : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer -in-charge, beyond 90 metre & upto 150 metre depth below ground level. 300 mm dia

Supplying, assembling, lowering and fixing in vertical position in bore well, ERW (Electric Resistance Welded) FE 410 plain slotted (having slot of size 1.6/3.2 mm) mild steel threaded and socketed / plain bevel ended pipe (type A) of required dia, conforming to IS: 8110, of reputed and approved make, having wall thickness not less than 5.40 mm, including painted with outside surface with two coats of anticorrosive bitumestic paint of approved brand and manufacture, including hire & labour charges, fittings & accessories, all complete, for all depths, as per direction of Engineer -in-charge. 100 mm nominal size dia

Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by “V” notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge.

Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of:100 mm dia

Providing and fixing M.S. clamp of required dia to the top of casing/housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts f required size complete. 100 mm clamp

Supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in

Supplying, filling, spreading & leveling coarse sand of size range 1.5 mm to 2 mm in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engineer -in-charge.

Supplying & Installation of approved Make required capacity 3 phase, 50 Hz, 415V, Submersible pump, with Control Panel Starter with Dry Run Protection, single phase preventer, connections, etc. as required as per specifications but excluding Pipe and connection cable. Water Pump submercible 2 No 3.0 HP Head-200m Discharge-170 Ltr/MMake:Lubi/ITT or equivalent

Planning, Designing, Detailing, Manufacturing, Supplying,Erection, Testing and Commissioning of Sewage Treatment Plant (STP) of 120 cu mt per day (Civil Part considered in Building ) including electrical ,mechanical and civil construction, STP based on Moving bed bio - film reactor technology including secondary treatment of pressure sand filter and activated carbon filter with necessary chlorine contact system complete to treat raw seawge from Domestic liquid waste with output characteristics as follows : pH-6 to 8 ,Total suspended solid less then 2 mg/lt COD less then 2 mg/lt BOD less then 0.5 mg/liter oil and grease nil Note:-Treated water will be used non human use i.e. flushing, gardining, etc.

Providing, fixing, testing and commissioning of vertical self supporting dual media filter fabricated from MS sheet as per IS : 2825, pressure gauges at inlet & outlet, sample cock, air vent valve with piping, GI class 'C' face piping distribution pipe with diffuser on top, CI butterfly valves Multiport valve and all accessories, with initial charge of filter media for dual media filter, painting inside with food grade epoxy paint and outside with two coat of red oxide primer and two or more coat of synthetic enamel paint complete.Dual Media Filter for Domestic Water Supply :Capacity - 10000 LPH ( 10.0m3/hour)Filtration rate - 15000 LPH/sqm (15 m3/hr/m2)Filter dia (approx.) - 600 mmWorking pressure - 3.0 Kg/Sq.cmTest pressure - 5.5 Kg/Sq.cmSupply,Installation, testing & commissioning

Providing, fixing, testing & commissioning vertical self supporting Activated Carbon Filter (ACF) fabricated from M.S. Sheet as per IS: 2825, pressure gauge at inlet & outlet, sample cock, G.I. Class 'C' face piping, C.I. Butterfly valve / Multiport Valve and all accessories, air vent valve with piping, with initial charge of filter media for activated carbon filter, painting inside with epoxy paint and outside with two coat of synthetic enamel paint complete.Capacity - 10000 LPH ( 10.0m3/hour)Filtration rate - 15000 LPH/sqm (15 m3/hr/m2)Filter dia (approx.) - 600 mmWorking pressure - 3.0 Kg/Sq.cmTest pressure - 5.5 Kg/Sq.cmSupply,Installation, testing & commissioning

Providing, fixing, testing & commissioning of metering pump type chemical doser with 100 lits.HDPE/ FRP solution tank, injection fitting assembly, suction and delivery hose upto the point of injection, capacity 0-6 lph, complete in all respects for treated water tank. Chlorination of Domestic Water : Supply,Installation, testing & commissioning

Providing , fixing, testing and commissioning of water softener fabricated from MS plate as per IS : 2825 (shell & thick dished ends) complete with initial charge of resins, GI class 'C' face piping, CI butterfly valves, pressure gauge, hydraulic brine injector, accessories, painting inside with epoxy paint and outside with two coat of red oxide primer and two or more coat of synthetic enamel paint, including suitable PVC/HDPE brine tank of 2 regeneration capacity complete with resins of approved quality and make.Hardness Inlet - 400 PPM (Approx.) Outlet - Commercial zero (<5 PPM) Capacity - 10000 LPH (14.4 m3/hour) Operating pressure - 3.0 kg/Sq.cm Test pressure - 5.5 Kg/Sq.cm Suggest ed Resin Quantity - 400Kg Suggested dia - 600 mm Supply,Installation, testing & commissioning

Providing, fixing, testing and commissioning of Electronic Level indicator including sensor, Display Panel, cabling and all fitting and accessories (For Underground Water Tank).

Providing, installation, testing and commissioning of centrifugal monoblock water transfer pumps domestic water UGT to OHT . The pump shall have cast iron casing, Bronze impeller, stainless steel shaft with mechanical seal, directly coupled with totally enclosed fan cooled induction motor, 2900 rpm mounted on a M.S. channel base frame including pressure gauge on delivery line with gunmetal isolation cock, suitable vibration elimination pads of approved quality and design, nuts, botls. Each pump shall be suitable for 415 ± 10% volts 3 phase 50 Hz A.C. Electric supply and shall be of the capacity as under: Flow Rate = 3.0 LPS Head = 60 Mtrs.(2 Nos. 1W+1S)

Providing, installation, testing and commissioning of centrifugal monoblock water transfer pumps treated water from STP to OHT . The pump shall have cast iron casing, Bronze impeller, stainless steel shaft with mechanical seal, directly coupled with totally enclosed fan cooled induction motor, 2900 rpm mounted on a M.S. channel base frame including pressure gauge on delivery line with gunmetal isolation cock, suitable vibration elimination pads of approved quality and design, nuts, botls. Each pump shall be suitable for 415 ± 10% volts 3 phase 50 Hz A.C. Electric supply and shall be of the capacity as under: Flow Rate = 2.0 LPS Head = 60 Mtrs.(2 Nos. 1W+1S)

Providing, installation, testing and commissioning of centrifugal monoblock filter feed pump Raw water UG tank to Domestic Water UG tank . The pump shall have cast iron casing, Bronze impeller, stainless steel shaft with mechanical seal, directly coupled with totally enclosed fan cooled induction motor, 2900 rpm mounted on a M.S. channel base frame including pressure gauge on delivery line with gunmetal isolation cock, suitable vibration elimination pads of approved quality and design, nuts, botls. Each pump shall be suitable for 415 ± 10% volts 3 phase 50 Hz A.C. Electric supply and shall be of the capacity as under: Flow Rate = 2.0 LPS Head = 20 Mtrs.(2 Nos. 1W+1S)

Supplying, installing, testing and commissioning of centrifugal mud sump pumps, suitable for 415 ± 10% Volts, 3 phase/230 ±10% volts 50 Hz A.C. power supply. Each pump shall suitable for automatic/manual operation complete with starter / control panel as per specification. Basement Storm Water/ Sewerage (2 Nos. 1 W + 1 S) Flow rate = 2.0 LPS Head = 15 Mtrs. Solid Handling = 32mm

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. Group C

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.2 X 4 sq. mm + 1 X 4 sq. mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 6 sq. mm + 1 X 6 sq. mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.4 X 10 sq. mm + 2 X 6 sq. mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.4 X 16 sq. mm + 2 X 6 sq. mm earth wire

Supplying and fixing metal box of following sizes (normal) on surface or recess with suitable size of phenolic laminated sheet cover in front including painting etc. as required. 100 mm x 100 mm x 60 mm deep

Supplying and fixing metal box of following sizes (normal) on surface or recess with suitable size of phenolic laminated sheet cover in front including painting etc. as required. 180 mm x 100 mm x 60 mm deep

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 5/6 A switch

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 3 pin 5/6 A socket outlet

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 1 or 2 Module (75mmX75mm)

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 3 Module (100mmX75mm)

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required. [P & RAW POWER]

Installation, testing and commissioning of pre-wired, fluorescent fitting / compact fluorescent/LED fitting of all types, complete with all accessories and tube etc. directly on ceiling/ wall, including connection with 1.5 sq. mm FR PVC insulated, copper conductor, single core cable and earthing etc. as required.

Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable, including providing and fixing phenolic laminated sheet cover on the fan box etc. as required.

Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required. Upto 450 mm sweep

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 12 way, Double door

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 4 way (4 + 12), Double door

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 8 way (4 + 24), Double door

Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCB/MCCBs (but without MCCB/MCBs and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.) 8 way (4 + 24), Double door

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Double pole

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Triple pole

Supplying and fixing following rating, double pole, (single phase and neutral), 240 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 30 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required. 25 amps

Supplying and fixing following rating, double pole, (single phase and neutral), 240 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 30 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 amps

Supplying and fixing following rating, four pole, (Three phase and neutral),415 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 30 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 amps

Supplying and Fixing Singe Pole Blanking Plate in the existing MCB DB complete etc. as required.

Providing and fixing M.V.. danger notice plate of 200 mm X 150 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required.

Supplying, installing by suspension on ceiling, testing and commissioning of following capacity Sandwich Type Rising Mains for use on 3 phase 4 wire 415 volts, 50Hz A.C. supply with metal clad enclosure having IP-54 rating after fixing the tap off boxes and all accessories, made of 1.6mm thick steel sheet duly powder coated in convenient sections complete with 4 Nos aluminium bus bars having current density of 130 A/ sq cm at nominal current rating, necessary joints, elbow joints & expansion joints and bends, fire barrier at Each floor, provision of tapping at every metre, adopter box and copper flexible for joints, continuous earthing with 2 Nos aluminium strip of suitable size (one on Each side) including, G.I. clamping brackets, suspenders, angle iron bracket, steel fasteners, connecting to earthing system etc. as required 400 A 30kA SC for 1 sec

Supplying, installing by suspension on ceiling, testing and commissioning of following capacity Sandwich Type Rising Mains for use on 3 phase 4 wire 415 volts, 50Hz A.C. supply with metal clad enclosure having IP-54 rating after fixing the tap off boxes and all accessories, made of 1.6mm thick steel sheet duly powder coated in convenient sections complete with 4 Nos aluminium bus bars having current density of 130 A/ sq cm at nominal current rating, necessary joints, elbow joints & expansion joints and bends, fire barrier at Each floor, provision of tapping at every metre, adopter box and copper flexible for joints, continuous earthing with 2 Nos aluminium strip of suitable size (one on Each side) including, G.I. clamping brackets, suspenders, angle iron bracket, steel fasteners, connecting to earthing system etc. as required 630 A 30kA SC for 1 sec

Supplying, installation, testing & commisioning of following capacity Plug In/ tap off box on the existing Air Insulated Compact Type bus trunking/ rising mains for use on 3 phase 4 wire 415 volts, 50Hz A.C. supply made with 1.6mm thick sheet steel enclosure (IP54) duly powder coated with provision of MCCB/ACB (but without MCCB/ACB) complete etc. as required125 A 15kA SC for 1 sec

Supplying, installation, testing & commisioning of following capacity Plug In/ tap off box on the existing Air Insulated Compact Type bus trunking/ rising mains for use on 3 phase 4 wire 415 volts, 50Hz A.C. supply made with 1.6mm thick sheet steel enclosure (IP54) duly powder coated with provision of MCCB/ACB (but without MCCB/ACB) complete etc. as required200 A 25kA SC for 1 sec

Supplying, installation, testing & commisioning of following capacity End Feed Unit for the existing Air Insulated Compact Type bus trunking/ rising mains for use on 3 phase 4 wire 415 volts, 50Hz A.C. supply made with 1.6mm thick steel sheet enclosure (IP54) duly powder coated with provision of MCCB/ACB (but without MCCB/ACB) complete with necessary joints including clamping brackets, angle iron bracket, steel fasteners, connecting to earthing system etc. as required 400 A 35kA SC for 1 sec

Supplying, installation, testing & commisioning of following capacity End Feed Unit for the existing Air Insulated Compact Type bus trunking/ rising mains for use on 3 phase 4 wire 415 volts, 50Hz A.C. supply made with 1.6mm thick steel sheet enclosure (IP54) duly powder coated with provision of MCCB/ACB (but without MCCB/ACB) complete with necessary joints including clamping brackets, angle iron bracket, steel fasteners, connecting to earthing system etc. as required 630 A 50kA SC for 1 sec

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 150 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 300 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "bends" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 150 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "bends" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 300 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "Tee" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 150 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "Tee" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 300 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "Cross member" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 150 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "Cross member" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 300 mm width X 50 mm depth X 1.6 mm thickness

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 Metre long etc. with charcoal/ coke and salt as required.

Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm)

Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required.

Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.

Providing and fixing 4mm dia.copper wire on surface or in recess for loop earthing as required.

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required.

Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CM/M/W) minimum 6.00, Air delivery minimum 210 Cum/Min , 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required.

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/HUME/METAL Pipe as required. Upto 35 sq. mm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/HUME/METAL Pipe as required. Above 35 sq. mm and upto 95 sq. mm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/HUME/METAL Pipe as required. Above 185 sq. mm and upto 400 sq. mm

Supplying and fixing cable route marker with 10 cm X 10 cm X 5 mm thick G.I. plate with inscription there on, bolted /welded to 35 mm X 35 mm X 6 mm angle iron, 60 cm long and fixing the same in ground as required.GI AND RCC PIPE

Supplying and fixing cable route marker with 10 cm X 10 cm X 5 mm thick G.I. plate with inscription there on, bolted /welded to 35 mm X 35 mm X 6 mm angle iron, 60 cm long and fixing the same in ground as required.GI AND RCC PIPE 40mm Dia, G. I. Pipe (medium class)

Supplying and fixing cable route marker with 10 cm X 10 cm X 5 mm thick G.I. plate with inscription there on, bolted /welded to 35 mm X 35 mm X 6 mm angle iron, 60 cm long and fixing the same in ground as required.GI AND RCC PIPE 32mm Dia, G. I. Pipe (medium class)

Supplying and fixing cable route marker with 10 cm X 10 cm X 5 mm thick G.I. plate with inscription there on, bolted /welded to 35 mm X 35 mm X 6 mm angle iron, 60 cm long and fixing the same in ground as required.GI AND RCC PIPE 100mm Dia, G. I. Pipe (medium class)

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3½ X 25 sq. mm (28mm)

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3½ X 70 sq. mm (38mm)

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3½ X 120 sq. mm (45mm)

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3½ X 300 sq. mm (70mm)

Supplying and making outdoor end termination with cast resin compound including aluminium lugs and other jointing materials for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required. 3½ X 25 sq. mm

Supplying and making outdoor end termination with cast resin compound including aluminium lugs and other jointing materials for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required. 3½ X 70 sq. mm

Supplying and making outdoor end termination with cast resin compound including aluminium lugs and other jointing materials for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required. 3½ X 120 sq. mm

Supplying and making outdoor end termination with cast resin compound including aluminium lugs and other jointing materials for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required.3½ X 300 sq. mm

Supplying and making outdoor end termination with cast resin compound including aluminium lugs and other jointing materials for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required. 95.00 mm² 3½ core U.G. CU. Cable

Supplying and making outdoor end termination with cast resin compound including aluminium lugs and other jointing materials for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required. 25.00 mm² 3½ core U.G. Cable

Supplying and making outdoor end termination with cast resin compound including aluminium lugs and other jointing materials for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required. 70.00 mm² 3½ core U.G. AL. Cable

Supplying and making outdoor end termination with cast resin compound including aluminium lugs and other jointing materials for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required. 120.00 mm² 3½ core U.G. AL Cable

Supplying and making outdoor end termination with cast resin compound including aluminium lugs and other jointing materials for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required. 300.00 mm² 3½ core U.G. AL Cable

300KVAR APFC WITH 7% HD HARMONIC DETUNED REACTOR CAPACITOR TYPE:- MPP (ABB/ SCHNEIDER/ CROMPTON GREAVES/ C&S/ SIEMENS/ L& T OR EQUIVALENT MAKE AS APPROVED BY THE Deptt.) Supplying including installation testing and commissioning of 300kVAr, 440V WITH 7% HD HARMONIC DETUNED REACTOR CAPACITOR TYPE:- MPP APFC Panel Non-Compartmentalized Type, Free Standing, Floor Mounted rated Voltage 440V rated Frequency 50Hz Number of phases 3 Phase Switching Option Auto-Manual ENCLOSURE DETAILS Material CRCA Thickness of sheet steel Frame & Doors: 2.0mm, Partitions: 1.6mm, Gland plate: 3.0mm Ingress Protection IP 42 Installation Type Indoor Cable Entry Bottom Colour RAL 7035 - Light Grey BUSBAR DETAILS Material Aluminium Cross Section (mm) 40 x 10 x 1 Run Bus bar Supports DMC Moulded CAPACITORS Heavy Duty @ 440V No of Steps 12 Incomer MCCB, 800A, 50kA CVS Type Switching Capacitor Duty Contactors Step Protection MCB/MCCB APFC RELAY INCOMER MCCB, 800A, 50kA CVS Type Digital Volt - Amp Freq meter 1 Phase Indicating Lamps (L1, L2, L3) 3 Current Transformer - 800/5A APFC Relay 1Fans 1 Control Circuit Protection - MCB 2 Step Indicating Lamps 12 On / Off push buttons 12 Step protection - MCCB, CVS Type, 25kA - 100A -3Nos., 63A-4Nos., 25A-5Nos.

Supplying and fixing following rating, Single pole, 415 volts, MCB in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 amps

Supplying and fixing following rating, Four pole, 415 volts, MCB in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 amps

Supplying and fixing following rating, Four pole, 415 volts, MCB in the existing MCB DB complete with connections, testing and commissioning etc. as required. 63 amps

Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required. 630 A, 50KA, 4P MCCB

Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required. 400 A, 36KA, 4P MCCB

Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required. 160 A, 25KA, 4P MCCB

Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required. 125 A, 25KA, 4P MCCB

Supplying of Indoor Decorative Recess mounted LED down lighter luminaries of make-PHILIPS CAT no.-RS262B LED20S/865 PSU MB WH 20W LED complete with all accessories such as ballast, starter etc. In the false ceiling type Armstrong /Gypsum or similar ceiling mounting with necessary support with 1.5 sq.mm. P.V.C. insulated S.C.copper conductor as required and as directed by the department ( Jaquar / LT / Wipro make). [PR]

Supplying of Superior finish extruded LED Batten white powder coated pressure die cast aluminium body with High transmitivity, non Yellowing PMMA diffuser with driver and accessories pre-wired upto terminal block assembly. LED Luminaires of make PHILIPS Cat No. BN170C LED40S- PSU L120 LED 40W or equivalent inlcuding lamps etc. complete [TL]

Supplying of Indoor Decorative Surface mounted LED down lighter luminaries of Make-PHILIPS CAT no.-SM296C LED20S-6500 PSU WH 20WATT complete with all accessories such as ballast, starter etc. In the ceiling mounting with necessary support with 1.5 sq.mm. P.V.C. insulated S.C.copper conductor as required and as directed by the department . [CR]

Supplying of Indoor Decorative Ceilling hanging mounted LED down lighter luminaries of Make-PHILIPS CAT No.-SM321P LED10S-5700 PSU NB DIA100 WH 10WATT complete with all accessories such as ballast, starter etc. In the false ceiling type Armstrong /Gypsum or similar ceiling mounting with necessary support with 1.5 sq.mm. P.V.C. insulated S.C.copper conductor as required and as directed by the department . [TR]

Supplying of Indoor Decorative Surface mounted LED Batten type deep recessed luminaries of Make-PHILIPS CAT no.SP780X H LED20S-6500 PSU W5L112 OC S1 WH 112WATT complete with all accessories such as ballast, starter etc. In the ceiling mounting with necessary support with 1.5 sq.mm. P.V.C. insulated S.C.copper conductor as required and as directed by the department .[TLC]

Supplying of Indoor Decorative Surface mounted LED Batten type deep recessed luminaries of Make-PHILIPS CAT no.SP780P LED26S-6500 PSU W5L113 OD WH 20WATT complete with all accessories such as ballast, starter etc. In the ceiling mounting with necessary support with 1.5 sq.mm. P.V.C. insulated S.C.copper conductor as required and as directed by the department .[TLD]

Supplying of Indoor Decorative Surface mounted LED Batten type deep recessed luminaries of Make-PHILIPS CAT no.SP780X LED12S-6500 PSU WH W5L5 113WATT complete with all accessories such as ballast, starter etc. In the ceiling mounting with necessary support with 1.5 sq.mm. P.V.C. insulated S.C.copper conductor as required and as directed by the department .[TLE]

Supplying of Indoor Decorative Surface mounted LED Batten type deep recessed luminaries of Make-PHILIPS CAT no.SP791X I LED27S 865 PSU W6L120 OC WH 120WATT complete with all accessories such as ballast, starter etc. In the ceiling mounting with necessary support with 1.5 sq.mm. P.V.C. insulated S.C.copper conductor as required and as directed by the department .[TLF]

Supplying of Indoor Decorative Surface mounted LED Batten type deep recessed luminaries of Make-PHILIPS CAT no.SP790P I LED28S 865 PSU W6L120 OC WH 120WATT complete with all accessories such as ballast, starter etc. In the ceiling mounting with necessary support with 1.5 sq.mm. P.V.C. insulated S.C.copper conductor as required and as directed by the department .[TLB]

Supplying of Indoor Decorative Surface mounted LED Batten type deep recessed luminaries of Make-PHILIPS CAT no.SP800P LED41 840 L120W6 SD 120WATT complete with all accessories such as ballast, starter etc. In the ceiling mounting with necessary support with 1.5 sq.mm. P.V.C. insulated S.C.copper conductor as required and as directed by the department . [CLSA]

Supplying, installation, testing and Commission of Indoor Decorative Recessed mounted 2' x 2' LED down lighter luminaries of Make-PHILIPS CAT no- SM367 LED 30S-6500 G6 L54W54 PUS OD WH OC with 30Watt LED lamp complete with all accessories such as ballast, starter etc. In the false ceiling type Armstrong /Gypsum or similar ceiling mounting with necessary support with 1.5 sq.mm. P.V.C. insulated S.C.copper conductor as required and as directed by the department ( Philips / Crompton / LT make). [CLTA]

Supplying, installation, testing and Commission of Indoor Decorative Recessed mounted 2' x 2' LED down lighter luminaries of Make-PHILIPS CAT no- SM367 LED42S-6500 G6 L54W54 PSU OD with 42Watt LED lamp complete with all accessories such as ballast, starter etc. In the false ceiling type Armstrong /Gypsum or similar ceiling mounting with necessary support with 1.5 sq.mm. P.V.C. insulated S.C.copper conductor as required and as directed by the department ( Philips / Crompton / LT make). [CLTB]

Supplying of Indoor Decorative Recessed mounted 2' x 2' LED down lighter luminaries of Make-PHILIPS CAT no- SP740B LED25S/840 W60L60 PSU WH with 25Watt LED lamp complete with all accessories such as ballast, starter etc. In the false ceiling type Armstrong /Gypsum or similar ceiling mounting with necessary support with 1.5 sq.mm. P.V.C. insulated S.C.copper conductor as required and as directed by the department ( Philips / Crompton / LT make). [CLSB]

Supplying of Indoor Decorative Recess mounted LED down lighter luminaries of make-PHILIPS CAT no.-DN296B LED20S-6500 PSU WH 20W LED complete with all accessories such as ballast, starter etc. In the false ceiling type Armstrong /Gypsum or similar ceiling mounting with necessary support with 1.5 sq.mm. P.V.C. insulated S.C.copper conductor as required and as directed by the department ( Jaquar / LT / Wipro make). (DN)

Supplying of 450 mm sweep Heavy duty exhaust fan 900rpm of make HAVELLS Cat/Brand TURBO FORCE-SP complete with all accessories complete or equivalent. [EFH]

Supply, Installation antistatic rubber mat suitable for 1.1 KV Voltage grade

Supply and installation of advanced encapsulated compound based CPRi tested maintenance free Pipe pin pipe technology upgraded (zinc and alloy coated) zinc coated (80 to 100) microns with Pure zinc 99.9% and alloy coating 200 to 250 microns Earthing system confirming ls 3043. The outer and inner pipe should be 762 mm and 41.9 mm dia or 48.3 mm and 26.4mm 3 meters length Copper bonded zinc coated with additional special pipes being filled up with compact fill crystaline conductive compound the Compact film mibxture which is machine pressed in the pipe should not disintegrate or collapse when outer pipe corrodes. The inner pIpe be extended with terminals for connectivity the job includes dealing the earthing should pits and refilling the same by Baron Electrode backfill compound. The BFC should be eco friendly it should not contain environmentally hazardous material metal having ROHS certification from NABL accredited lab. The earthpit should be provided with FRP or EPCC earthpit cover for protection and safeguard of terminals in areas where soil condition is bad. Good earth that is black cotton or moisture normal soil is to be arranged to fill the excavated pits by mixing the arranged soil with BFC 2-4 bags electrode BFC for installation of earth electrode. Resistance of Earthing should be less than 1 ohm. Make:Zenith/ Indelec/Erico/Macmate.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providng and fixing 2 nos. 6 pin 15/16 A modular socket outlet and 2 nos. 15/16 A modular switch, connections etc. as required. (For UPS POWER POINT). [SOC}

Supplying including installation testing and commissioning of Lightning Protection System using one or more OPR Units mustbe performed in accordance wth manufactrer's recomendatons as well as clients satifactory requirements and NF C17-102 (Edition 2011) with OPR efficiency [Delta A] 60Micro Second. The Rolling sphere Protection Radious shall be 60/65 metres with appropiate length of G I Mast POle [4Mtrs.] and Base Plat,Insulator, Lightning Strike Counter & Test Link. The Grounding Rod (17.2mmX3 Metres Long) shall be Copper Bonded and Polymer Pit Cover Round with proper connections, Clampings etc. 10Sqmm Single Core Copper Cable as required as Directed. UPS SYSTEM upplying including installation of Inverter (NUMERIC/Hitachi/ APC/ Eaton) with Battery and its case as per direction and specified by the Deptt.

Supply, Installation, testing & commissioning of Three Phase (3-Phase Input and 3-Phase Output), 160 KVA, Modular/Scalable, On-line, Double Conversion (VFI), UPS, in PRS configuration, with Isolation Transformer. The Day-1 KVA rating of the moulder UPS would be 160 KVA; scalable to 200KVA or more. The UPS shall be supplied with MODBUS/BMS and Ethernet ports with software for real-time UPS health monitoring, Fault Diagnostics upto the battery status, temperature, cell voltage, capacity remaining, run time etc UPS shall be housed in Seismic-rated enclosures, include heavy-duty, torsion-resistant construction to withstand industrial vibrations and other severe seismic movement. Similarly, It is critical that the entire batteries shall be mounted on a Seismic-rated enclosures 19” / 23” heavy-duty, torsion-resistant rack installation, that can withstand severe seismic movement beyond five. UPS OEM must guarantee that the offered batteries, as per supplied specifications provide a minimum back up time of 30~45 minutes at 160 KVA, in full rated load - Per frame/rack. (Dummy load to be provided for load and parameter testing and acceptance.

Supply including installation of Inverter with Battery and its case as per direction and specified by the Dept. 2KVA On-Line UPS System having 0.9 P.F, with PWM-IGBT technology 240V AC Input (170V – 280VA. 1 Ph input- 1 Ph output, preferably with inbuilt Isolation Transformer, 2KW output, 60min backup, with batteries as per supplied specifications, mounted on proper Rack, Battery interlink cables etc.

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 Metre long etc. with charcoal/ coke and salt as required.

Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm)

Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required.

Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.

Providing and fixing 4mm dia.copper wire on surface or in recess for loop earthing as required.

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required.

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavatoin, sand cushioning, protective covering and refilling the trench etc, as required. Upto 35 sq. mm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavatoin, sand cushioning, protective covering and refilling the trench etc, as required. Above 35 sq. mm and upto 95 sq. mm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavatoin, sand cushioning, protective covering and refilling the trench etc, as required. Above 185 sq. mm and upto 400 sq. mm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/HUME/METAL Pipe as required. Upto 35 sq. mm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/HUME/METAL Pipe as required. Above 35 sq. mm and upto 95 sq. mm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/HUME/METAL Pipe as required. Above 185 sq. mm and upto 400 sq. mm

Supplying and fixing cable route marker with 10 cm X 10 cm X 5 mm thick G.I. plate with inscription there on, bolted /welded to 35 mm X 35 mm X 6 mm angle iron, 60 cm long and fixing the same in ground as required.

GI AND RCC PIPE40mm Dia, G. I. Pipe (medium class)

GI AND RCC PIPE 32mm Dia, G. I. Pipe (medium class)

GI AND RCC PIPE 100mm Dia, G. I. Pipe (medium class)

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3½ X 25 sq. mm (28mm)

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3½ X 70 sq. mm (38mm)

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3½ X 300 sq. mm (70mm)

Supplying and making outdoor end termination with cast resin compound including aluminium lugs and other jointing materials for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required. 3½ X 300 sq. mm

Supplying and making outdoor end termination with cast resin compound including aluminium lugs and other jointing materials for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required. 4.00 mm2 3core U.G. Cable

Supplying and making outdoor end termination with cast resin compound including aluminium lugs and other jointing materials for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required. 6.00 mm2 3core U.G. Cable

Supplying and making outdoor end termination with cast resin compound including aluminium lugs and other jointing materials for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required. 25.00 mm² 3½ core U.G. Cable

Supplying and making outdoor end termination with cast resin compound including aluminium lugs and other jointing materials for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required. 70.00 mm² 3½ core U.G. Cable

Supplying and making outdoor end termination with cast resin compound including aluminium lugs and other jointing materials for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required. 300.00 mm² 3½ core U.G. Cable

Design, Manufacture, Supplying, Fixing in position, Testing & Commissioning of floor mounted Feeder Pillar including all components housed in 16 SWG cubicle type sheet steel floor mounting, outdoor type as required with dust proof, hinged and lockable doors complete with inter-connections with copper wires, taps, bonding to earth & painting in line with specification, complete with neutral, earth strips of adequate size & drawings. Astronomical timer switch – 1 no. Busbar: 100 Amps TPN Copper Busbar (25mmX3mm) Outgoings: 32 amps DP MCB –5 nos 16 amps switch and socket – 1 no. 24" tube light with switch inside feeder pillar – 1 no.

Supplying,installation,testing and commissioning of the following integral flood lighting luminaires conforming to IP 65 / IP 66 suitable for vertical and horizontal mounting applications pressure die cast powder coated aluminium alloy housing with corrosion resistance powder coating using nano Technology transparent injection moulded poly carbonate UV stabilized diffuser having high impact strength to withstand min IK09 with high power LED and unique flood optics to ensure uniform light distribution and maintenance free system ideal for area lighting and billboard. The luminaires should be equiped with external surge protection device to withstand 10 KV / 5KV including connection with 2.5 sqmm 3 core PVC insulated round copper conductor as required and as directed by the department. PHILIPS MAKE CAT REF: BVP 120 LED047 CW FLNB FG A1 PSU GR 120Watt LED. [FDL]

Supplying with fitting and fixing sheet steel cable junction box of size 40cm x 20cm x 15 cm made of 16 SWG thick MS Sheet with provision for hinge door and panel locking arrangement complete painted with 2 coats of metal primer and 2 coats of enamelled gloss paint of approved brand and manufacture to give an even shape including cleaning surface to remove of all dirt, dust and other foreign matter, the box is to be fitted on the bottom section of pole with minimum 165 mm dia 25 mm x 5mm size flat iron pole clamp complete with making necessary connection as directed consisting of the following electrical items. 12mm x 2mm x 15cm long 2 strip copper Bus Bar - 1 set 6-32 Amp "L" series DP MCB - 1 No. 6 amp "L" series SP MCB as outgoing - 2 Nos.

Supplying, installation, testing and commissioning of the following of the street light luminairies of the following specification "Die Cast Aluminum housing acting as Heat Sink for reliable performance. ü Prismatic Diffuser to ensure Road Light Distribution Operating Voltage 220 – 240V /50 Hz AC ü Luminaire Efficacy of >60 lm/W ü CRI : 75 ü Ingress Protection : IP 65ü Suitable for side entry with pole diameter of 28mm to 40mm conforms to IEC598 Section 5 part 1, conforms to IEC598 Section 4 part 1, has lifetime of 50000 Hours with constant lumen output. ü Output luminaous flux of luminaire - 5700 Lumens. (a) WIPRO make Cat No.LR02-102-XXX-57-XX 90W LED. [STL] Supplying including installation of the Octagonal poles shall be designed to withstand the maximum wind speed of 169 km/hr. The top loading i.e. area and weight of fixtures are to be considered to calculate maximum deflection of the poles and the same shall meet the requirement of BS:5649 Part VI 1982. The pole shaft shall have octagonal cross section and shall be continuously tapered with single longitudinal welding. There shall not be any circumferential welding of the pole shaft. The welding of the pole shaft shall be done by Submerged Welding process. All octagonal pole shafts shall be provided with the rigid flange plate of suitable thickness with provision for fixing 4 foundation bolts. The base plate shall be fillet welded to the pole shaft at two locations i.e. from inside and outside. The welding shall be done as per process approved by Third Party Inspection agency. (BAJAJ/ PHILIPS/ VALMONT/ PARUTHI ENGR/Nezone make)

Pole Type BOP or equivalent-9030 Height 9m The materials of the pole as follows : Conforming to grade S355JO Conforming to grade S355JO, Base Plate :- Fe 410 Conforming to IS 226/ IS 2062, Foundation Bolts:- 6.8 Gr. As per IS 1367, Pole Sections:- The Octagonal Poles shall be in single piece with single longitudinal welding join, Galvanization :- The poles shall be hot dip galvanized as per IS 2629 / IS 2633 / IS 4759 standards with average coating thickness of 65 micron. The galvanizing shall be done in single dipping. Door opening:- The Octagonal poles shall have door of approximate 500 mm length at the elevation of 500 mm from the base plate. The door shall be vandal resistance and shall be weather proof to ensure safety of inside connection as approved by the Depts.. The door shall be flush with the exterior surface and shall have suitable locking arrangement. The pole shall be adequately strengthened at the location of the door compensate for the loss in section. There shall also be suitable arrangement for the purpose of earthing, Smart pack Junction box with 6 MCB & Terminals for mounting inside base compartment of Pole. Top Dia. :- (A/ 70, Bottom Dia.:- (A/ 155 , Sheet Thickness :- 3mm , Base Plate Dimensions :- (L x B x 260 x 260 x 16, Foundation Bolt Size :- (no. x dia.) 4 x 24 Dia, Pitch Circle Dia.:- (PC 250 Bolt Length:- 750, Projected Bolt Length :-125 Anchor plate thickness :- 4 mm , Pole Foundation :- The octagonal poles shall be bolted on a pre- cast foundation with a set of four foundation bolts for greater rigidity. Foundation:- The foundation shall be done with ( Earth work 2.04 cubic Meters.RCC 1:1.5 : 3 proportion 0.65 cubic metres. Steel 22.43 Kg. Shuttering 4.32 square metres. = 22.43 Kg.

Supplying including fitting and fixing of Hot Dip galvanised arm bracket for installation of luminaries. Header with top cap 300 mm long pipe of thickness 3 with arrangement to fix on pole top with 3 Nos. of bolts. i Armed of required length size 48.3mm out side dia x 3.25mm thick (BAJAJ/ PHILIPS/ VALMONT/ PARUTHI ENGR/Nezone make) Stiffener plate from arm of the following types : Single arm bracket 1000mm long for 3m to 10 metre. Poles.

Supplying, installation, testing and commissioning of pressure die cast powder coated aluminium alloy housing frosted PC diffuser, IP65/IP66 protection with build in LED of the following landscape luminarie ( POST TOP ) suitable for 38mm dia post top mounting applications including connections with 2.50 sq.mm 3core multistrand P.V.C. insulated round copper cable as required and directed by the department. PHILIPS CAT REF: BGP200 LED26 CW PSU GR CPC SPD25 26WATT. [PTL]

Supply,installation,testing and commissioning of IP 65, 13W Inverted type LED bollard Height: 920mm Holder: B 22 Black with 360 degree light distribution. Make ; PHILIPS ( Ref. Cat. No. BCP150 LED150/WW PSU 220-240V 7043 Bollard or equvalent K-LIGHT as approved. [BL}

Supply, Installation antistatic rubber mat suitable for 1.1 KV Voltage grade

Supply and installation of advanced encapsulated compound based CPRi tested maintenance free Pipe pin pipe technology upgraded (zinc and alloy coated) zinc coated (80 to 100) microns with Pure zinc 99.9% and alloy coating 200 to 250 microns Earthing system confirming ls 3043. The outer and inner pipe should be 762 mm and 41.9 mm dia or 48.3 mm and 26.4mm 3 meters length zinc coated with additional special pipes being filled up with compact fill crystaline conductive compound the Compact film mibxture which is machine pressed in the pipe should not disintegrate or collapse when outer pipe corrodes. The inner pIpe be extended with terminals for connectivity the job includes dealing the earthing should pits and refilling the same by Baron Electrode backfill compound. The BFC should be eco friendly it should not contain environmentally hazardous material metal having ROHS certification from NABL accredited lab. The earthpit should be provided with FRP or EPCC earthpit cover for protection and safeguard of terminals in areas where soil condition is bad. Good earth that is black cotton or moisture normal soil is to be arranged to fill the excavated pits by mixing the arranged soil with BFC 2-4 bags electrode BFC for installation of earth electrode. Resistance of Earthing should be less than 1 ohm. Make:Zenith/ Indelec/Erico/Macmate.

Load security deposit to be deposited to concerned Power Supply Agency with check meter as well as permission from Power Supply Authority including liasioning with all the concerned departments etc..

Supervision Charges and Liaision Charges to be paid to Power Supply Agency

Supplying including installation, testing and commissioning of Air/Water Cooled Diesel Generator set coupled to suitable alternator of 220/415 V, AC, 1/3-Phase 0.8 p.f.(la mounted on a 1) M.S. Fabricated base frame.,2) M.S. fuel tank of required capacity.,3) Residual Silencer.,4) Standard Control Panel.5) Suitable batteries with lead.,5) First fill of lube oil.,6) Acoustic Enclosure complete with all accessories as specified and directed by the department conforming to CPCB-IV+EMMISSION COMPLIANT and IS comprising the Technical Specification WITH SYNCRONYSING PANEL with 2Nos.X500KVA DG And 1No.X500KVA SPARE as per SLD and as per manufacturer. (RANGE FROM 5 KVA TO 625 KVA) CAPTIVA/bliss, Leyland, Volvo Penta, Perkinson, Mahindra, engine and Kirloskar, Stamford, Leroy somer alternator.KVA- PHASE- Approx size- Approx Wt - COOLING 500 - 3 -6200x2100x2570- 7500 Kg W/C

(A)Supplying,installation,testing and commissioning of electric driven pressurisation pump suitable for automatic operation and consisting of following, complete in all respects, as required : (Jockey Pump) (B) Horizontal type, multistage, centrifugal pump of cast iron body and bronze impeller with stainless steel shaft, mechanical seal conforming toIS:1520. (C) Suitable HP squirell cage induction motor TEFC type suitable for operationon415volts,3phase50HzACsupplywithIP55classof protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS : 325. (D) M.S.fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. (E) Suitable cement concrete foundation duly plastered and with anti vibrationpads. 180 LPM at 56 Mtr. Head

Designing, Supply, Installation, Testing and commissioning of system controller to control operation of main electric fire pump, diesel pump, Pressurization pump, Terrace pump in sequence as per specification consisting of relays, timers. Sensors, annunciation window for fault indication, complete as per specification

Designing, Supply, Installation, Testing and commissioning of system controller to control operation of main electric fire pump, diesel pump, Pressurization pump, Terrace pump in sequence as per specification consisting of relays, timers. Sensors, annunciation window for fault indication, complete as per specifications.

Designing, Supply, Installation, Testing and commissioning of system controller to control operation of main electric fire pump, diesel pump, Pressurization pump, Terrace pump in sequence as per specification consisting of relays, timers. Sensors, annunciation window for fault indication, complete as per specifications.

Designing, Supply, Installation, Testing and commissioning of system controller to control operation of main electric fire pump, diesel pump, Pressurization pump, Terrace pump in sequence as per specification consisting of relays, timers. Sensors, annunciation window for fault indication, complete as per specifications.

Designing, Supply, Installation, Testing and commissioning of system controller to control operation of main electric fire pump, diesel pump, Pressurization pump, Terrace pump in sequence as per specification consisting of relays, timers. Sensors, annunciation window for fault indication, complete as per specifications.

Providing laying, testing & commissioning of 'C' class heavy duty MS Pipe conforming to IS 1239/3589 l/c fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. in ground including welding. excavation & providing cement concrete blocks as supports, anticorrosive treatment with coaltar/asphalt tane as per IS 10221 refilling the trench ETC. of the following sizes complete as required 150 mm. Dia

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required:25 mm dia.

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required:32 mm dia.

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required:` 40 mm dia.

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required:`50 mm dia.

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required:`65 mm dia.

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required:`80 mm dia.

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required:`100 mm dia.

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required:`150 mm dia.

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required:`200 mm dia. (wall thickness 6.3 mm)

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required:` 250 mm dia. (wall thickness 6.3 mm)

Supplying and fixing single headed internal hydrant valve with Instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type A) with blank gunmetals/stainless steel cap and chain as required : Single handed gunmetal

Supplying and fixing single headed external yard hydrant valve with no. 1 63 mm Instantaneous FM Gunmetal/Stainless Steel coupling with cast iron wheel ISI marked conforming to IS 5290 (Type A) with blank gunmetals/stainless steel cap and chain as required :Single handed gunmetal

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required: 65 mm dia

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required: 80 mm dia

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required:100 mm dia

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required: 150 mm dia

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required: 200 mm dia

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required:250 mm dia

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, Gl bolts, nuts, washers etc.as required:80 mm dia

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, Gl bolts, nuts, washers etc.as required: 100 mm dia

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, Gl bolts, nuts, washers etc.as required: 150 mm dia

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, Gl bolts, nuts, washers etc.as required:250 mm dia

Providing, installation, testing and commissioning of stainless steel Y-strainer fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm dia holes with stainless steel flange.200 mm dia

Supplying and fixing 63 mm m long RRL hose pipe with 63 mm dia male and female couplings duly bound with Gl wire, rivets etc. conforming to IS 636 (type-A) as required: Gun metal

Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required. 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585 20 mm nominal internal dia gun metal globe valve & nozzle. Drum and brackets for fixing the equipmets on wall. Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket. 30 m

Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required: Gun metal

Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required: 2 way-100 mm dia M.S. Pipe

Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required: 4 way - 150 mm dia M.S. Pipe

Supplying and fixing air vessel made of 250 mm dia, 8 mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and painting with synthetic enamel paint of approved shades as required :

Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories: Pendent Sprinkler

Providing & fixing of pressure switch in M.S. pipe line including connection etc. as required.

Providing & fixing flow switch in following sizes M.S. pipe including connection etc as required 150 mm dia

Providing, fixing, testing & commissioning of installation control valve of cast iron body, brass/bronze working parts comprising of water motor alarm, bronze seat clapper, clapper arm and hydraulically driven mechanical gong bell to sound continuous alarm when the wet riser/sprinkler system activates, pressure gauges, emergency releases, strainer, pressure switch, cock valve complete with drain valve and bypass, test control box, ball valves, MS pipe of required size, flanges, orifice plate, gasket etc of follwing sizes as required 150 mm dia

Supplying, installation, testing & commissioning of sprinkler flexible pipe (UL Listed) of stainless steel complete with 15 NPT on reducer thread with maximum working pressure of 175 PSI test pressure of 875 PSI (Burst) with branch line (Inlet) 25mm NPT male thread to sprinkler head (Outlet) 15mm NPT female thread with reducer, nipple, 2 side brackets, center bracket, stockbar of following sizes complete as required. 700 mm

Providing & fixing of IS marked (IS:15683) portable fire extinguisher, carbondioxide type flat base including valve, discharge hose of not less than 10 mm dia. 1 M long & complete in all respects including initial fill with CO2 gas confirming to IS:15222 filled to a filling ratio of not more than 0.667 and wall suspension bracket Capacity 4.5 kg

6 Kg. ABC MAP-90% Powder type fire extinguishers are manufactured and marked to Indian standard IS: 15683. Hose shall made of EPDM Rubber, CE Marked Valve, Suitable first aid appliance for fighting fires in Class A, B & C fire that is wood, textile, flammable liquids & gases.

Providing & fixing of IS marked (IS: 13386-1992) mechanical foam type fire extinguishers 50 kg consisting of welded M.S. trolley mounted cylindrical body, squeeze lever discharge valve fitted with pressure discharge hose, discharge nozzle, trolley etc. finished externally with red enamel paint and fixed to wall with brackets complete with internal charges

K (Kitchen) type 6 Ltr. Stored Pressure type Fire Extinguisher, with UGTS Pressure Gauge, Deep Drawn, Stainless Steel Body, EPDM Rubber Hose with SS Nozzle, CE Mark Valve with Safety Release Provision, Helium Leak Detection Tested, Controllable discharge mechanism applicable on Class K (Kitchen) Fire, maintenance, care and refilling as per IS 2190:2010

Sand Bucket with Stand (6 Bucket)

Providing, Fixing, of Photo luminescent Self charge EXIT Sign boards of approximate size 12" x 6" The colour combination and letter size shall be in accordance with IS: 9457-1980, IS: 12349- 1988. complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR .

GAS SUPPRESSION 25 BAR SYSTEM (FK5112)80L 25BAR SAPPHIRE ASSEMBLY

120L 25BAR SAPPHIRE ASSEMBLY

SAPPHIRE / FK5112 AGENT PER 1KG

Supervisory presure switch - standard (open on fall)

Electrical Actuator - UL Bridge Rectifier and Placement Switch (TLXUS)

LOCAL MANUAL ACTUATOR

Male adaptor (1/4" BSPT x 1/4" BSPP)

Male elbow (1/4" NPT x 1/4" BSPP )

DN1/4" PTFE flexible actuation hose x 710mm

2" FLEXIBLE DISC HOSE

Pr. SWT, DPST, WP (2-3/4'' outl't), Lat.

34L & 80 litre 267Ø container bracket

SAPPHIRE (FK-5-1-12) door caution plate (less than NOAEL - no lock off) - English

SAPPHIRE (FK-5-1-12) manual release caution plate - English

Brass nozzle - 360 degree NPT - India

Gas Release Panel

Smoke/Heat detector

Hooter

Wiring Fire Alarm to devices

Battery

Piping Work As area

Supplying, installation, testing and commissioning of reapter panel with 320 character/ Touch screen LCD display with inbuilt reset, acknowledge and silence switches complete as required.

Supplying, installation, testing and commissioning of intelligent analog addressable photo thermal detector complete with mounting base complete as required.

Supplying, installation, testing and commissioning of response indicator on surface/ recessed. MS Box having two LED, metallic cover complete with all connection as required.

Supllying, installation, testing and commissioning of fault isolator base complete as required.

Supplying, installation, testing and commissioning of intelligent analog addressable thermal detector with rate of rise cum fixed temp. thermistor complete with base as required.

Supplying, installation, testing and commissioning of addressable fire control module complete as required.

Supplying, installation, testing and commissioning of addressable manual call point complete as required.

Supplying, installation, testing and commissioning of addressable horn cum strobe complete as reqired.

Supplying, installation, testing and commissioning of fire fighter telephone handset complete as required.

Supplying, installation, testing and commissioning of fore fighter phone jack complete as required.

SITC of UV Flame detector operating Volage 24 V DC

SITC of addressable Zone module to connect conventional devices

Supplying, installation, testing and commissioning of 6 zones, voice alarm controller with USB, MP3 player 9including 6 zone botton paging station) with seamless integration facility with main fire panel alarm for voice evacuation complete as required.

Supplying, installation, testing and commissioning of 10W ceiling speakers complete as required.

Supplying, installation, testing and commissioning of 10W metal box ceiling/wall speakers complete as required.

Supplying and laying of 2*1.5 sqmm fire survival armoured cable, 600/1000V rated with annealed copper conductor having glass mica fire barrier tape covered by exterude layer of cross linkable Ethylene propylene Rubber (EPR) insulation and LSZH inner bedding, steel wire armouring & LSZH outer sheath complete as required.

Supplying and drawing of Oxygen free stranded copper conductor to IS 8130, class 5 or class 6 Insulated with Transparent PVC Operation Temperature Max.: 70˚ C Voltage Rating 1100 V Speaker cable two pair, 2-core.1.5 sqmm

Main table Size- 2350mm (W) x 2350mm (D) x 750mm (H) Primary work surface:Made of 25mm thick MDF­one side pre­laminate board confirming to IS­14587:1998 with 0.4mm PVC membrane pressed on to top Softclosing access flap with in-build power box are provided on work surface for wire management. Secondary Work Surface:Made of 25mm thick MDF­one side pre­laminate board confirming to IS­14587:1998 with 0.4mm PVC membrane pressed on to top. Modesty Panel: Made of 25mm thick MDF­one side pre­laminate board confirming to IS­14587:1998 with 0.4mm PVC membrane pressed on to top. Under- structure: Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Integrated Pedestal: Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Drawer fronts made of 25mm thick MDF­one side pre­laminate board confirming to IS­14587:1998 with 0.4mm PVC membrane pressed on to top Pedstal construction is BOX-BOX-FILE type which Uses powder coated 400 MM long metal Panel Drawer Slides. Drawer extension is 325 MM. Drawers have a soft closing & anti slam mechanism. Handles are provided for ease of opening. Pedestals are provided with lock for security Dimension: Primary surface 1650 mm (W) X 1650mm (D) x 750 mm (H). Product should be cretified with Greenguard (UL), IAQ Gold, Green Pro. OEM Should be a BIFMA member and should have at least 18 products in BIFMA complianc registry.OEM should have a valid BIFMa membership with having more than 20 products in BIFMA compliance registry. OEM should be Greenguard certified and should have more than 20 products in UL greenguard registry.

Size- 2350mm (W) x 500mm (D) x 750mm (H) Top Panel 750 H Back Unit 1650/1800/2350 W DATE:16.09.21 Slide Door Unit Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping for body panels like side, bottom,back and shelves. Shutters are made of 25mm thick MDF­one side pre­laminate board confirming to IS­14587:1998 with 0.4mm PVC membrane pressed on to top. Shutters have a soft closing & anti slam mechanism. Handles are provided for ease of opening. Storage is provided with lock for security. Made of 25mm thick MDF­one side pre­laminate board confirming to IS­14587:1998 with 0.4mm PVC membrane pressed on to top. Product should be cretified with Greenguard (UL), IAQ Gold, Green Pro. OEM Should be a BIFMA member and should have at least 18 products in BIFMA complianc registry. OEM should have a valid BIFMa membership with having more than 20 products in BIFMA compliance registry. OEM should be Greenguard certified and should have more than 20 products in UL greenguard registry.

The cushioned seat should be made of injection moulded Plastic outer & inner. Plastic inner should be upholstered with leatherette and moulded High resilience polyurethane foam of density 45+/-2 kg/m3, and hardness load 16+/-2 kgf as per IS :7888 for 25% compression.The cushioned back is made of PU foam with insitu molded MS ERW Round tube of size 1.9+/-0.03cm x 0.16+/-0.0128 cm.It should be upholstered with leatherite. Seat size :47 cm (W) x 48 cm (D). High back size :47.7cm (W) x 76.4 cm (D). Mid back size : 47.7 cm (W) x 60.1cm (D). The product should have Green Guard(UL) Gold, BIFMA Level 2, IAQ Gold, Green Pro & GRIHA certifications. OEM should have a valid BIFMa membership with having more than 20 products in BIFMA compliance registry. OEM should be Greenguard certified and should have more than 20 products in UL greenguard registry.

Visitor chair The cushioned seat should be made of injection moulded Plastic outer & inner. Plastic inner should be upholstered with leatherette and moulded High resilience polyurethane foam of density 45+/-2 kg/m3, and hardness load 16+/-2 kgf as per IS :7888 for 25% compression.The cushioned back is made of PU foam with insitu molded MS ERW Round tube of size 1.9+/-0.03cm x 0.16+/-0.0128 cm.It should be upholstered with leatherite. Seat size :47 cm (W) x 48 cm (D). High back size :47.7cm (W) x 76.4 cm (D). Mid back size : 47.7 cm (W) x 60.1cm (D). The product should have Green Guard(UL) Gold, BIFMA Level 2, IAQ Gold, Green Pro & GRIHA certifications. OOEM should have a valid BIFMa membership with having more than 20 products in BIFMA compliance registry. OEM should be Greenguard certified and should have more than 20 products in UL greenguard registry.

TV Unit All carcass panel are made of 18 mm prelaminated particle board with edge banding 1.5 mm thickness. • Upper vertical side are of 18 mm thickness in PU • Bottom side doors are of 18 mm thick MDF in PU on front • Bottom middle doors are made of 4 mm thick toughened glass with PU paint in black • All doors are fitted with push to open fittings • Levellers are provided on vertical panels at back to rest the unit properly against the wall OEM should have a valid BIFMa membership with having more than 20 products in BIFMA compliance registry. OEM should be Greenguard certified and should have more than 20 products in UL greenguard registry.

2 seater sofa Width: 146 cm Depth: 92.0 cm Height: 82 cm and Seat Height 45.0 cm Seat Foam: The Seat is made of PU Foam with Density 32+/- 2 kg/cu .mtr having an additional top layer of PU Foam with Density 28+/- 2 kg/cu.mtr, Seat is upholstered wuth Fabric or Leatherite.Back Foam: The Back is made of PU Foam with Density 28 +/- 2 kg/cu .mtr having an additional top layer of PU Foam with Density 23+/- 2 kg/cu.mtr, Backis upholstered wuth Fabric or Leatherite. understructure: unterstructure is made up of 1.2+/- 0.1 cm thick hote pressed plywood , 4mm Dia zigzag Spring is mounted in the understructure for support and additional cushioning purpose. Leg Assembly: is welded assembly made in SS 202 Grade tube and plate. OEM should have a valid BIFMa membership with having more than 20 products in BIFMA compliance registry. OEM should be Greenguard certified and should have more than 20 products in UL greenguard registry.

Center Table Product should have 10±0.3mm thick black tinted toughened glass UV glued with bushes made in SS 202 grade for fixing with understructure. It is a welded Assembly made in SS202 grade having dia 12±0.04 as per IS:1762 SIZE: 112cm(W)X60cm(D)X34.9(H). OEM should have a valid BIFMa membership with having more than 20 products in BIFMA compliance registry. OEM should be Greenguard certified and should have more than 20 products in UL greenguard registry.

sideTable Product Should have 10±0.3mm thick black tinted toughened glass UV glued with bushes made in SS 202 grade for fixing with understructure. It is a welded Assembly made in SS202 grade having dia 12±0.04 as per IS:1762 SIZE: 60cm(W)X60cm(D)X34.9(H) OEM should have a valid BIFMa membership with having more than 20 products in BIFMA compliance registry. OEM should be Greenguard certified and should have more than 20 products in UL greenguard registry.

8'W Linear Desk Size- 2400mm (W) X 725Dmm (D) X 740Hmm (H) Overall dimension should be (2400W X 1770D X 740H) with worksurface counter 1035mm H. Desk should comprise of 1. Rubber wood Top with clean matt PU finish 18mm thick, inside radius 700mm, outside radius 1350mm, depth 650mm. 2. Rubberized cork with 18mm thick 3. 10 mm thick diamond cut frosted glass, inside radius 1202.5mm, outside radius 1402.5mm, dept 200mm. Understructure should comprise of MS perforated sheet modesty panel, below worksurface should be 0.8mm thick*665.0mm height * 1345mm flat length. Above worksurface should be 0.8mm Thick* 260mm Height * 1345mm Flat length. Legs should be 1.6mm thick MS tube with diameter 50.8mm, height 604mm. Product should be certified with Greenguard (UL) and IAQ Gold. OEM should have a valid BIFMa membership with having more than 20 products in BIFMA compliance registry. OEM should be Greenguard certified and should have more than 20 products in UL greenguard registry.

chair SEAT ASSEMBLY Should be made up of 1.5 ± 0.1 cm thick hot - pressed plywood upholstered with fabric and moulded polyurethane foam. SEAT SIZE: 51.8cm (W) x 49.7cm (D). The Back is injection moulded in glass filled Nylon which is upholstered with Mesh fabric.The back consist of adjustable Lumbar support made of injection moulded Polypropylene having an adjustment of 5.0 ±0.1 cm. BACK SIZE: 47.9 cm(W) x 66.9 cm (H). HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane seat foam is moulded with density 45+/-2 kg/m³ and hardness 16 ± 2 kgf as per IS:7888 for 25% compression. ARMRESTS (ADJUSTABLE) :The height adjustable armrest is made of Polypropylene and can be adjusted to 6.0±0.1cm height.It also has swivel and To and Fro adjustment with moulded PU armtop. ACTIVE BIO-SYNCHRO MECHANISM: The adjustable tilting mechanism is designed with the following features: · 360° revolving type · Front-pivot for tilt with feet resting on ground & continuous lumber support ensuring more comfort. · Tilt tension adjustment can be operated in seating position. · 5 position Tilt limiter giving option of variable tilt angle to the chair. · Seat / back tilting ratio of 1:2. · The mechanism housing is made up of HPDC Aluminium & black powder coated (DFT 40 to 60 micron). The pneumatic height adjustment with an adjustment stroke of 10.0 ± 0.3cm. Product SHould be Greenguard (UL), Green Pro, IAQ GOLD, GRIHA and BIFMA Level 2 certified. OEM should have a valid BIFMa membership with at least 10 products in BIFMA compliance registry. OEM should be Greenguard certified and should have 10 products in UL greenguard registry, with also have IAQ Gold Certification, Green pro Certification.

Conference table 10 seater Size- 3000mm (W) X 1150mm (D) X 740mm (H) Work Surface : Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Plastic ABS access flap is provided for easy access to wires and cables. Work top is available in various shapes as shown above. Understructure: It consist of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Aluminium alloy 63400 - WP profile is used for connecting panels together. The product has a knock-down construction. Modesty Panel: Made of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Powder coated accent metal strip provided below work surface to enhance aesthetics. It is made of 0.8mm CRCA as per IS 513,epoxy polyester powder coated (DFT 40-60 microns. Wire Management: An array of panels made of 0.8mm CRCA MS IS:513, epoxy polyester powder coated (DFT 40-60 microns) is used for flow of wires and cables. Provision to mount Anchor Roma 6 module plate is provided below worktop. Cutout on top with two piece injection moulded plastic part polymer component is fitted to pull out audio,video cables onto worktop and connect devices charger to power socket below worktop. Product should be Greenguard (UL), IAQ Gold, Green Pro and GRIHA. OEM should have a valid BIFMa membership with having more than 20 products in BIFMA compliance registry. OEM should be Greenguard certified and should have more than 20 products in UL greenguard registry.

Conference Chair he seat is made up of 1.2±0.1cm thick hot pressed plywood and upholstered with fabric or synthetic leather and moulded Polyurethane foam.the back is made up 1.2±0.1cm thick hot pressed plywood upholstered with replaceable fabric or synthetic leather upholstery covers and mouldedp polyurethane foam.The back ply and foam is designed with contoured lumber support for comfortable seating posture.Back size:48cm(W) x 64.5 cm(H),seat size : 51cm(W) x 48cm(D).The high resilience polyurethane foam for seat and back is moulded with density 45±2kg/m³ and hardness load16±2 kgf as per IS:7888 for 25% compression.The armrest top is made of moulded polyurethane and mounted on to a drop lift height adjustable type M.S. Tubular armrest support chrome plated.The armrest height is adjustable upto 6.5±0.5cm. In 5 steps & also has swivel adjustment of 22°±2° on both sides.The mechanism is knee-tilt synchro mechanism with following features:360° revolving type,single point control,front pivot for tilt with feet resting on ground ensuring more comfort,tilt tension adjustment,4 position locking with anti-shock feature,seat/back tilting ratio of 1:2 and seat depth adjustment of 6.0±0.5cm can be locked in 6 positions.The backrest consists of a sliding up down mechanism,which can be adjusted in the range of 7.5±0.5cm and can be locked in 4 positions for correct position of lumber support.The pneumatic height adjustment has an adjustment of 9.0±0.3cm.The pedestal is fabricated from 0.2±0.02cm thick high resilience sheet(IS:DD 1079/HR skin pass),chrome plated and assembled with injection moulded black polypropylene hub cap and 5 nos. Twin wheel castors.The pedestal is 66.0±0.05cm.Pitch center dia (76.0±1.0cm with castors).The twin wheel castors are injection moulded in black nylon.OEM should have a valid BIFMa membership with having more than 20 products in BIFMA compliance registry. OEM should be Greenguard certified and should have more than 20 products in UL greenguard registry.

16 seater Conference Table Work Surface : Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Plastic ABS access flap is provided for easy access to wires and cables. Work top is available in various shapes as shown above. Understructure: It consist of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Aluminium alloy 63400 - WP profile is used for connecting panels together. The product has a knock-down construction. Modesty Panel: Made of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Powder coated accent metal strip provided below work surface to enhance aesthetics. It is made of 0.8mm CRCA as per IS 513,epoxy polyester powder coated (DFT 40-60 microns). Wire Management: An array of panels made of 0.8mm CRCA MS IS:513, epoxy polyester powder coated (DFT 40-60 microns) is used for flow of wires and cables. Provision to mount Anchor Roma 6 module plate is provided below worktop. Cutout on top with two piece injection moulded plastic part polymer component is fitted to pull out audio,video cables onto worktop and connect devices charger to power socket below worktop. Product should be Greenguard (UL), IAQ Gold, Green Pro and GRIHA. OEM should have a valid BIFMa membership with having more than 20 products in BIFMA compliance registry. OEM should be Greenguard certified and should have more than 20 products in UL greenguard registry.

Conference Chair The seat is made up of 1.2±0.1cm thick hot pressed plywood and upholstered with fabric or synthetic leather and moulded Polyurethane foam.the back is made up 1.2±0.1cm thick hot pressed plywood upholstered with replaceable fabric or synthetic leather upholstery covers and mouldedp polyurethane foam.The back ply and foam is designed with contoured lumber support for comfortable seating posture.Back size:48cm(W) x 64.5 cm(H),seat size : 51cm(W) x 48cm(D).The high resilience polyurethane foam for seat and back is moulded with density 45±2kg/m³ and hardness load16±2 kgf as per IS:7888 for 25% compression.The armrest top is made of moulded polyurethane and mounted on to a drop lift height adjustable type M.S. Tubular armrest support chrome plated.The armrest height is adjustable upto 6.5±0.5cm. In 5 steps & also has swivel adjustment of 22°±2° on both sides.The mechanism is knee-tilt synchro mechanism with following features:360° revolving type,single point control,front pivot for tilt with feet resting on ground ensuring more comfort,tilt tension adjustment,4 position locking with anti-shock feature,seat/back tilting ratio of 1:2 and seat depth adjustment of 6.0±0.5cm can be locked in 6 positions.The backrest consists of a sliding up down mechanism,which can be adjusted in the range of 7.5±0.5cm and can be locked in 4 positions for correct position of lumber support.The pneumatic height adjustment has an adjustment of 9.0±0.3cm.The pedestal is fabricated from 0.2±0.02cm thick high resilience sheet(IS:DD 1079/HR skin pass),chrome plated and assembled with injection moulded black polypropylene hub cap and 5 nos. Twin wheel castors.The pedestal is 66.0±0.05cm.Pitch center dia (76.0±1.0cm with castors).The twin wheel castors are injection moulded in black nylon. OEM should have a valid BIFMa membership with having more than 20 products in BIFMA compliance registry. OEM should be Greenguard certified and should have more than 20 products in UL greenguard registry.

Conference table 8 seater Size- 2350mm (W) X 1150mm (D) X 740mm (H) Worktop Should be Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Access Flap provided with soft closing hinges, Under structure The Under-structure should consist of mixture of 25mm and 18mm Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Anodised aluminium alloy 63400 - WP profile is added at bottom edges for improving the aesthetics. The product has a knock-down construction. A wire raise should made of 0.8mm CRCA MS IS:513. It is epoxy polyester powder coated (DFT 40-60 microns) for flow of wires and cables. Cutout provision below Access flap at two locations for standard 8 module Anchor Roma is provided. Beside each cutout, an additional cutout with plate is provided for mounting Audio Visual Cables (eg.HDMI, VGA-A,etc). Product should be Greenguard (UL), IAQ Gold, Green Pro and GRIHA. OEM should have a valid BIFMa membership with having more than 20 products in BIFMA compliance registry. OEM should be Greenguard certified and should have more than 20 products in UL greenguard registry.

Conference Chair The seat is made up of 1.2±0.1cm thick hot pressed plywood and upholstered with fabric or synthetic leather and moulded Polyurethane foam.the back is made up 1.2±0.1cm thick hot pressed plywood upholstered with replaceable fabric or synthetic leather upholstery covers and mouldedp polyurethane foam.The back ply and foam is designed with contoured lumber support for comfortable seating posture.Back size:48cm(W) x 64.5 cm(H),seat size : 51cm(W) x 48cm(D).The high resilience polyurethane foam for seat and back is moulded with density 45±2kg/m³ and hardness load16±2 kgf as per IS:7888 for 25% compression.The armrest top is made of moulded polyurethane and mounted on to a drop lift height adjustable type M.S. Tubular armrest support chrome plated.The armrest height is adjustable upto 6.5±0.5cm. In 5 steps & also has swivel adjustment of 22°±2° on both sides.The mechanism is knee-tilt synchro mechanism with following features:360° revolving type,single point control,front pivot for tilt with feet resting on ground ensuring more comfort,tilt tension adjustment,4 position locking with anti-shock feature,seat/back tilting ratio of 1:2 and seat depth adjustment of 6.0±0.5cm can be locked in 6 positions.The backrest consists of a sliding up down mechanism,which can be adjusted in the range of 7.5±0.5cm and can be locked in 4 positions for correct position of lumber support.The pneumatic height adjustment has an adjustment of 9.0±0.3cm.The pedestal is fabricated from 0.2±0.02cm thick high resilience sheet(IS:DD 1079/HR skin pass),chrome plated and assembled with injection moulded black polypropylene hub cap and 5 nos. Twin wheel castors.The pedestal is 66.0±0.05cm.Pitch center dia (76.0±1.0cm with castors).The twin wheel castors are injection moulded in black nylon. OEM should have a valid BIFMa membership with having more than 20 products in BIFMA compliance registry. OEM should be Greenguard certified and should have more than 20 products in UL greenguard registry.

13 seater conference table Worktop Should be Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Access Flap provided with soft closing hinges, Under structure The Under-structure should consist of mixture of 25mm and 18mm Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Anodised aluminium alloy 63400 - WP profile is added at bottom edges for improving the aesthetics. The product has a knock-down construction. A wire raise should made of 0.8mm CRCA MS IS:513. It is epoxy polyester powder coated (DFT 40-60 microns) for flow of wires and cables. Cutout provision below Access flap at two locations for standard 8 module Anchor Roma is provided. Beside each cutout, an additional cutout with plate is provided for mounting Audio Visual Cables (eg.HDMI, VGA-A,etc). Product should be Greenguard (UL), IAQ Gold, Green Pro and GRIHA. OEM should have a valid BIFMa membership with having more than 20 products in BIFMA compliance registry. OEM should be Greenguard certified and should have more than 20 products in UL greenguard registry.

Conference Chair The seat is made up of 1.2±0.1cm thick hot pressed plywood and upholstered with fabric or synthetic leather and moulded Polyurethane foam.the back is made up 1.2±0.1cm thick hot pressed plywood upholstered with replaceable fabric or synthetic leather upholstery covers and mouldedp polyurethane foam.The back ply and foam is designed with contoured lumber support for comfortable seating posture.Back size:48cm(W) x 64.5 cm(H),seat size : 51cm(W) x 48cm(D).The high resilience polyurethane foam for seat and back is moulded with density 45±2kg/m³ and hardness load16±2 kgf as per IS:7888 for 25% compression.The armrest top is made of moulded polyurethane and mounted on to a drop lift height adjustable type M.S. Tubular armrest support chrome plated.The armrest height is adjustable upto 6.5±0.5cm. In 5 steps & also has swivel adjustment of 22°±2° on both sides.The mechanism is knee-tilt synchro mechanism with following features:360° revolving type,single point control,front pivot for tilt with feet resting on ground ensuring more comfort,tilt tension adjustment,4 position locking with anti-shock feature,seat/back tilting ratio of 1:2 and seat depth adjustment of 6.0±0.5cm can be locked in 6 positions.The backrest consists of a sliding up down mechanism,which can be adjusted in the range of 7.5±0.5cm and can be locked in 4 positions for correct position of lumber support.The pneumatic height adjustment has an adjustment of 9.0±0.3cm.The pedestal is fabricated from 0.2±0.02cm thick high resilience sheet(IS:DD 1079/HR skin pass),chrome plated and assembled with injection moulded black polypropylene hub cap and 5 nos. Twin wheel castors.The pedestal is 66.0±0.05cm.Pitch center dia (76.0±1.0cm with castors).The twin wheel castors are injection moulded in black nylon. OEM should have a valid BIFMa membership with having more than 20 products in BIFMA compliance registry. OEM should be Greenguard certified and should have more than 20 products in UL greenguard registry.

Storwel Plain Size- 1981(H) x 916(W) x 486(D) Big size almirahof 916mm W x 486mm D x 1981mm H made of 0.7mm thick CRCA MS epoxy powder coated with welded construction. The almirah should have 4 adjustable shalves made with 0.8mm thick CRCA MS. The doors should be metal door made with0.8mm thick CRCA MS having mozac handles with m10 screw type leaver. Product should be Greenguard (UL), Green Pro, IAQ Gold, and GRIHA. OEM should have a valid BIFMa membership with having more than 20 products in BIFMA compliance registry. OEM should be Greenguard certified and should have more than 20 products in UL greenguard registry.

Size- 1500 (W1) X 1500 (W2) X 600 (D) Workstation made with combination of tile and pannel base partition. The partition panel should be 52 mm thick made with vertical and horizontal aluminium extrusions. The partition should be made with 4 nos. horizontal blocks of 259mm (approx). The bottom block should have metal tile in both side made with 0.8mm thick CRCA steel and the middle part should be hollow to accomodate wire and should work as wire carrier. The lower and upper middle block should be made with composite construction of 3mm thick MDF and 38mm thick paper honeycomb wrapped in fabric upholstery. The top tile should be made with pre laminated perticle board. The work top shoud be made with 25mm prelaminated pertical board supported with worksurface bracket. The partition pannels should be supported with metal legs made with CO2 welded MS Tube of section 38 mm x 25 mm. Size of each workstation should be 1500mm W1 x 1500 mm W2 x 600mm D1 x 600mm D2 x 1200mm H. Each workstations shoudl have 1 no. of 3 drawer all steel free standing pedestal + 1 no. Metal Cpu Trolley + 1 Plastik Key Board Trey. Product should be Greenguard (UL), IAQ Gold, Green Pro and GRIHA, Bifma level 2. OEM should have a valid BIFMa membership with having more than 20 products in BIFMA compliance registry. OEM should be Greenguard certified and should have more than 20 products in UL greenguard registry.

Chair Chair should have pneumatic seat height adjustment facility. Height of the chair should be atleast 110cm. Depth and width of the chair should be at least 76cm. Seat height should be at least 54cm.Back size-47.5cmWx69.5cmH. The seat and back should be made up of 1.2±0.1 cm thick hot pressed plywood upholstered with fabric upholstery cover and moulded polyurethane foam .The back Foam should be designed with countered lumbar support for extra comfort. The High resilience polyurethane Foam should be moulded with density=45±2kg/m3 and hardness load 16±2 kgf. The armrest should be injection moulded from black Co polymer polprylene. It should have centre tilt mechanism with tilt tension adjustment, upright position locking, 360 degree revolving and seat back tilting ratio should be 1:3.The pedestal should be injection moulded in black 33% glass filled Nylon-66. The pedestal should also have 5 nos twin wheel castor. Product should be IAQ Gold, Green Pro and GRIHA. OEM should have a valid BIFMa membership with having more than 20 products in BIFMA compliance registry. OEM should be Greenguard certified and should have more than 20 products in UL greenguard registry.

Size- 1650mm (W) x 700mm (D) x 743mm (H) (Main Desk) 1000mm (W) x 450mm (D) x 743mm (H) (ERU) Product Understructure should be The understructure is in prelam panels, made with PLT boards. 2­Drawer and 3­Drawer storage units with different combinations to support Tops, made with 18mm PLT boards of different colours. Modesty and back panels, made with 18mm PLT boards. The Pedestals/Storages are fitted with necessary Locks PLT Board Tops (Straight Edges): Tops for Junior1, Junior2, and Middle desk with ERU are of 18mm thickness. Made of 18mm thick PLT board with 2mm Edge banding. Wenge and Savannah Maple PLT board used for making Tops. PVC membrane Tops (with profiles): Tops for senior main and back unit desk are of PVC membrane pressed. Made of 25mm thick MDF­one side laminate board with 0.4mm PVC membrane pressed on to tops. The top has Duck nose and half round profiles edges. The top is made in only one finish: European Ash. OEM should have a valid BIFMa membership with having more than 20 products in BIFMA compliance registry. OEM should be Greenguard certified and should have more than 20 products in UL greenguard registry.

The seat & back is made up of 1.2 ± 0.1cm thk. hot pressed plywood measured as per QA method described in OCP-QLTA-PL14-18 upholstered with synthetic leather over moulded High Resilience Polyurethane foam. * BACK SIZE: 51.8 cm. (W) x 75.2 cm. (H) The HR polyurethane foam is moulded with density = 55+/-2 kg/m³ and hardness 16 ± 2 kgf as per IS:7888 for 25% compression.The adjustable armrest is designed with the following features : Up-Down adjustment– 8 steps (8.0±0.5 cm range) , Height adjustable armrest structure which is powder coated & fitted with an armrest top, Fixed Armrest Top is PU molded over metal insert.The adjustable tilting mechanism is designed with the following features.360° revolving type, Single point control, Front-pivot for tilt with feet resting on ground ensuring more comfort, Tilt tension adjustment. 4-position locking with anti-shock feature Seat/back tilting ratio of 1:2.moulded High Resilience Polyurethane foam. Back SIZE: 51.8 cm. (W) x 75.2 cm. (H). Back can be adjusted in 5 positions by manually.Stroke of height adjustable spine is 7 cm. Back height adjustability is applicable for for High back and Mid back chair. The pneumatic height adjustment has an adjustment stroke of 10.0 ± 0.3 cm.The pedestal is High Pressure Die cast polished Aluminium and fitted with 5 nos. twin wheel castors. The pedestal pitch-canter dia is Ø65.0± 0.5 cm. (75.0 ± 1.0 cm. with castors).The twin wheel castors are injection moulded in black PP. Product should be Greenguard (UL), GRIHA. OEM should have a valid BIFMa membership with having more than 20 products in BIFMA compliance registry. OEM should be Greenguard certified and should have more than 20 products in UL greenguard registry.

visitor chair The seat & back is made up of 1.2 ± 0.1cm thk. hot pressed plywood measured as per QA method described in OCP-QLTA-PL14-18 upholstered with synthetic leather over over moulded High Resilience Polyurethane foam. * MID BACK SIZE: 51.6 cm. (W) x 65.7 cm. (H) The HR polyurethane foam is moulded with density = 55+/-2 kg/m³ and hardness 16 ± 2 kgf as per IS:7888 for 25% compression.The tubular frame is powder coated ( DFT 40-60microns ) cantilever structure & made of Dia.Ø 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. M.S. E.R.W.Tube with a connecting M.S. Spine welded to it. Back spine is fitted to the frame assembly. Product should be Greenguard (UL) and GRIHA. OEM should have a valid BIFMa membership with having more than 20 products in BIFMA compliance registry. OEM should be Greenguard certified and should have more than 20 products in UL greenguard registry.

Storwel Plain Size- 1981(H) x 916(W) x 486(D) Big size almirahof 916mm W x 486mm D x 1981mm H made of 0.7mm thick CRCA MS epoxy powder coated with welded construction. The almirah should have 4 adjustable shalves made with 0.8mm thick CRCA MS. The doors should be metal door made with0.8mm thick CRCA MS having mozac handles with m10 screw type leaver. Product should be Greenguard (UL), Green Pro, IAQ Gold, and GRIHA. OEM should have a valid BIFMa membership with having more than 20 products in BIFMA compliance registry. OEM should be Greenguard certified and should have more than 20 products in UL greenguard registry.

4 Drawer Filing Cabinets Size- 1320mm (H) x 470mm (W) x 620mm (D) It should have rigid knock down construction made of CRCA. Panel Thicknes: Top side and drawer front 0.7mm. Frames, Drawer- inside cover,side back side 0.6mm.back,bottom and drawer bottom-0.5mm.The drawer front should have easy to grip full length handle recess integrated into metal drawer fronts. The filing cabinet should also have sanp on type label holder on drawer front. It should have centralized locking with 10 lever cam lock and have anti tipping arrangment to ensure that when one drawer is opened for use, it doesnt allow other drawers to be opened. The drawers should be mounted on high quality precision ball slides. The uniformly distributed load capacity of drawers should be 40 kg for 75000 cycles. It should have plain triangular plate pop riveted at bottom corner for rigidity. Accesories like drawer partition and cradle for hanging A4 files front to back should be there. Epoxy powder coated finish of thickness 50 microns (+/-10 ). Dimension: 1320mmhx470mmDx620mmD. Product should be certified with IAQ Gold. OEM should have a valid BIFMa membership with having more than 20 products in BIFMA compliance registry. OEM should be Greenguard certified and should have more than 20 products in UL greenguard registry.

13 seater conference Table Worktop Should be Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Access Flap provided with soft closing hinges, Under structure The Under-structure should consist of mixture of 25mm and 18mm Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Anodised aluminium alloy 63400 - WP profile is added at bottom edges for improving the aesthetics. The product has a knock-down construction. A wire raise should made of 0.8mm CRCA MS IS:513. It is epoxy polyester powder coated (DFT 40-60 microns) for flow of wires and cables. Cutout provision below Access flap at two locations for standard 8 module Anchor Roma is provided. Beside each cutout, an additional cutout with plate is provided for mounting Audio Visual Cables (eg.HDMI, VGA-A,etc). Product should be Greenguard (UL), IAQ Gold, Green Pro and GRIHA. OEM should have a valid BIFMa membership with having more than 20 products in BIFMA compliance registry. OEM should be Greenguard certified and should have more than 20 products in UL greenguard registry.

conference chair The seat is made up of 1.2±0.1cm thick hot pressed plywood and upholstered with fabric or synthetic leather and moulded Polyurethane foam.the back is made up 1.2±0.1cm thick hot pressed plywood upholstered with replaceable fabric or synthetic leather upholstery covers and mouldedp polyurethane foam.The back ply and foam is designed with contoured lumber support for comfortable seating posture.Back size:48cm(W) x 64.5 cm(H),seat size : 51cm(W) x 48cm(D).The high resilience polyurethane foam for seat and back is moulded with density 45±2kg/m³ and hardness load16±2 kgf as per IS:7888 for 25% compression.The armrest top is made of moulded polyurethane and mounted on to a drop lift height adjustable type M.S. Tubular armrest support chrome plated.The armrest height is adjustable upto 6.5±0.5cm. In 5 steps & also has swivel adjustment of 22°±2° on both sides.The mechanism is knee-tilt synchro mechanism with following features:360° revolving type,single point control,front pivot for tilt with feet resting on ground ensuring more comfort,tilt tension adjustment,4 position locking with anti-shock feature,seat/back tilting ratio of 1:2 and seat depth adjustment of 6.0±0.5cm can be locked in 6 positions.The backrest consists of a sliding up down mechanism,which can be adjusted in the range of 7.5±0.5cm and can be locked in 4 positions for correct position of lumber support.The pneumatic height adjustment has an adjustment of 9.0±0.3cm.The pedestal is fabricated from 0.2±0.02cm thick high resilience sheet(IS:DD 1079/HR skin pass),chrome plated and assembled with injection moulded black polypropylene hub cap and 5 nos. Twin wheel castors.The pedestal is 66.0±0.05cm.Pitch center dia (76.0±1.0cm with castors).The twin wheel castors are injection moulded in black nylon. OEM should have a valid BIFMa membership with having more than 20 products in BIFMA compliance registry. OEM should be Greenguard certified and should have more than 20 products in UL greenguard registry.

Storwel Plain Size- 1981(H) x 916(W) x 486(D) Big size almirahof 916mm W x 486mm D x 1981mm H made of 0.7mm thick CRCA MS epoxy powder coated with welded construction. The almirah should have 4 adjustable shalves made with 0.8mm thick CRCA MS. The doors should be metal door made with0.8mm thick CRCA MS having mozac handles with m10 screw type leaver. Product should be Greenguard (UL), Green Pro, IAQ Gold, and GRIHA. OEM should have a valid BIFMa membership with having more than 20 products in BIFMA compliance registry. OEM should be Greenguard certified and should have more than 20 products in UL greenguard registry.

size 1500x600 It should be made with combination of tile and pannel base partition. The partition panel should be 52 mm thick made with vertical and horizontal aluminium extrusions. The partition should be made with 4 nos. horizontal blocks of 259mm (approx). The bottom block should have metal tile in both side made with 0.8mm thick CRCA steel. The middle part should be hollow to accomodate wire and should work as wire carrier. The lower and upper middle block should be made with composite construction of 3mm thick MDF and 38mm thick paper honeycomb wrapped in fabric upholstery. The top tile should be made with pre laminated perticle board. The work top shoud be made with 25mm prelaminated particle board supported with worksurface bracket. The partition pannels should be supported with metal legs made with CO2 welded MS Tube of section 38 mm x 25 mm. Size of each workstation should be 1200mm W x 600mm D x 1200mm H. Each workstations shoudl have 1 no. of 3 drawer all steel free standing pedestal + 1 no. Metal Cpu Trolley + 1 n. Plastick Key Board Trey. (as per layout). Product should be Greenguard (UL), IAQ Gold, Green Pro and GRIHA, Bifma level 2. OEM should have a valid BIFMa membership with having more than 20 products in BIFMA compliance registry. OEM should be Greenguard certified and should have more than 20 products in UL greenguard registry.

The cushioned seat is made of injection moulded plastic outer and inner. Plastic inner is upholstered with stitched cover and moulded HR PU foam of density 45+-2 kg per cubic metre and hardness load 16+-2 kgf load. The stitched cover should be made from spacer fabric and leatherite. Seat size should be 47cm x 48cm. The cushioned back should be made of PU foam with insitu molded MS ERW round tube of size 1.9cm x 0.16cm. It should be upholstered with spacer fabric and leatherite. Back size should be 45cm x 75.5cm. The powder coated tubular frame is cantilever type and made of dia 2.54+/-0,03cm x 0.2+/-0.016cm thk MS ERW tube. The back connected to frame through powder coated high pressure die cast connector piece. Product should be Greenguard (UL), IAQ Gold, Green Pro and Bifma level 2. OEM should have a valid BIFMa membership with having more than 20 products in BIFMA compliance registry. OEM should be Greenguard certified and should have more than 20 products in UL greenguard registry.

13 seater conference Table Worktop Should be Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Access Flap provided with soft closing hinges, Under structure The Under-structure should consist of mixture of 25mm and 18mm Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Anodised aluminium alloy 63400 - WP profile is added at bottom edges for improving the aesthetics. The product has a knock-down construction. A wire raise should made of 0.8mm CRCA MS IS:513. It is epoxy polyester powder coated (DFT 40-60 microns) for flow of wires and cables. Cutout provision below Access flap at two locations for standard 8 module Anchor Roma is provided. Beside each cutout, an additional cutout with plate is provided for mounting Audio Visual Cables (eg.HDMI, VGA-A,etc). Manufacturer should be certified with ISO18001, ISO 9001, ISO 14001 and a member of BIFMA. Product Should be GREENGUARD (UL), IAQ GOLD & GREENPRO Certified

conference chair The seat is made up of 1.2±0.1cm thick hot pressed plywood and upholstered with fabric or synthetic leather and moulded Polyurethane foam.the back is made up 1.2±0.1cm thick hot pressed plywood upholstered with replaceable fabric or synthetic leather upholstery covers and mouldedp polyurethane foam.The back ply and foam is designed with contoured lumber support for comfortable seating posture.Back size:48cm(W) x 64.5 cm(H),seat size : 51cm(W) x 48cm(D).The high resilience polyurethane foam for seat and back is moulded with density 45±2kg/m³ and hardness load16±2 kgf as per IS:7888 for 25% compression.The armrest top is made of moulded polyurethane and mounted on to a drop lift height adjustable type M.S. Tubular armrest support chrome plated.The armrest height is adjustable upto 6.5±0.5cm. In 5 steps & also has swivel adjustment of 22°±2° on both sides.The mechanism is knee-tilt synchro mechanism with following features:360° revolving type,single point control,front pivot for tilt with feet resting on ground ensuring more comfort,tilt tension adjustment,4 position locking with anti-shock feature,seat/back tilting ratio of 1:2 and seat depth adjustment of 6.0±0.5cm can be locked in 6 positions.The backrest consists of a sliding up down mechanism,which can be adjusted in the range of 7.5±0.5cm and can be locked in 4 positions for correct position of lumber support.The pneumatic height adjustment has an adjustment of 9.0±0.3cm.The pedestal is fabricated from 0.2±0.02cm thick high resilience sheet(IS:DD 1079/HR skin pass),chrome plated and assembled with injection moulded black polypropylene hub cap and 5 nos. Twin wheel castors.The pedestal is 66.0±0.05cm.Pitch center dia (76.0±1.0cm with castors).The twin wheel castors are injection moulded in black nylon.OEM should have a valid BIFMa membership with having more than 20 products in BIFMA compliance registry. OEM should be Greenguard certified and should have more than 20 products in UL greenguard registry.

New Modular Control Desk for provision of 08 monitors & 02 Operators made in " XLAT" system.1. Table top: - The material of the working surface shall be minimum 12/18 thick Compact Laminate. The proposed Control Desk’s life cycle should be assessed (from approved LCA consultant) for environmental impacts associated with all the stages of a product's life for cradle to grave analysis. Valid report/document from UL/Intertek to be submitted along with the technical bid.2. Structure: 2.1. Made of heavy-duty extruded vertical and horizontal aluminium profiles. The extrusions shall be duly powder coated with 40+ microns over all surfaces. All sheet metal parts shall be finished with a durable, black, electrostatic powder coating. OEM shall have a valid trademark registration certificate issued by the Government of India for the Control Desk proposed in this tender. Valid Trademark registration certificate to be submitted along with the technical bid.2.2. To allow future extension and expansion, a weld-free system shall be proposed. Interconnecting joints shall not be visible. The structure shall be rigid enough to withstand BIFMA X5.5 tests.The structure shall allow easy assembly of hinged shutters, slat wall, gland plate, and monitor arms in extremely rigid manner. Valid certificate of BIFMA X5.5 from authorized agencies to be submitted along with technical Bid.2.3. The EPD (Environmental product declaration) of Control Desk shall be verified in accordance with ISO 14025 (from UL/Intertek) for Impacts on Environment by Control Desk. Valid report/document from UL/Intertek to be submitted along with the technical bid.2.4. Consoles shall be tested and qualified to sustain seismic vibrations as per design spectrum IS 1893 for zone 4 vibrations with monitor mounted on monitor arms of the control room console. Seismic safety of user & equipment is a prime concern area. This test shall be carried out by authorised government agency. Test report with images of control room console seismic test shall be submitted along with technical bid.3. Slat Wall: - Slat wall shall be made of approximately 2mm thick extruded aluminium (aluminium alloy). 4. Monitor Arm: - The Console shall feature ergonomic display mounting arms. It shall enable quick & easy replacement of VESA mounts & arm extensions. UL audit certified design feature of monitor arm assembly shall have auto lock, push & remove feature for quick release of VESA mounts and modular arm extensions for ease in maintenance and fixing of monitor by one technician within 30 seconds without using any tools. Valid UL audit certificates to be submitted along with the technical bid.5. The proposed control desk shall be ANSI/BIFMA e3-2019 certified/tested at least for level 3 from UL/Intertek as per Furniture Sustainability Standard to identify the sustainability level of the furniture with respect to the environmental, health & wellness, and social impacts applicable to product(s). Valid certificate to be submitted along with the technical bid.6. Shutters & Side Legs: - Front, and back shutters shall be of 18 mm Laminated MDF Board with premium finish.Side leg shall be of 25mm of the same finish.The central portion of the side leg shall feature illuminated strip on the periphery. To ensure healthier air quality for the operators. The proposed console shall be Greenguard Gold certified. Valid certificate to be submitted along with the technical bid.7.The proposed console shall be RoHS Certified/tested from UL/Intertek and the valid certificate/ test report shall be submitted along with the technical bid.

New Modular Control Desk for provision of 02 monitors & 01 Operator made in " XLAT" system.1. Table top: - The material of the working surface shall be minimum 12/18 thick Compact Laminate. The proposed Control Desk’s life cycle should be assessed (from approved LCA consultant) for environmental impacts associated with all the stages of a product's life for cradle to grave analysis. Valid report/document from UL/Intertek to be submitted along with the technical bid.2. Structure: - 2.1. Made of heavy-duty extruded vertical and horizontal aluminium profiles. The extrusions shall be duly powder coated with 40+ microns over all surfaces. All sheet metal parts shall be finished with a durable, black, electrostatic powder coating. OEM shall have a valid trademark registration certificate issued by the Government of India for the Control Desk proposed in this tender. Valid Trademark registration certificate to be submitted along with the technical bid.2.2. To allow future extension and expansion, a weld-free system shall be proposed. Interconnecting joints shall not be visible. The structure shall be rigid enough to withstand BIFMA X5.5 tests.The structure shall allow easy assembly of hinged shutters, slat wall, gland plate, and monitor arms in extremely rigid manner. Valid certificate of BIFMA X5.5 from authorized agencies to be submitted along with technical Bid.2.3. The EPD (Environmental product declaration) of Control Desk shall be verified in accordance with ISO 14025 (from UL/Intertek) for Impacts on Environment by Control Desk. Valid report/document from UL/Intertek to be submitted along with the technical bid.2.4. Consoles shall be tested and qualified to sustain seismic vibrations as per design spectrum IS 1893 for zone 4 vibrations with monitor mounted on monitor arms of the control room console. Seismic safety of user & equipment is a prime concern area. This test shall be carried out by authorised government agency. Test report with images of control room console seismic test shall be submitted along with technical bid.3. Slat Wall: - Slat wall shall be made of approximately 2mm thick extruded aluminium (aluminium alloy). 4. Monitor Arm: - The Console shall feature ergonomic display mounting arms. It shall enable quick & easy replacement of VESA mounts & arm extensions. UL audit certified design feature of monitor arm assembly shall have auto lock, push & remove feature for quick release of VESA mounts and modular arm extensions for ease in maintenance and fixing of monitor by one technician within 30 seconds without using any tools. Valid UL audit certificates to be submitted along with the technical bid.5. The proposed control desk shall be ANSI/BIFMA e3-2019 certified/tested at least for level 3 from UL/Intertek as per Furniture Sustainability Standard to identify the sustainability level of the furniture with respect to the environmental, health & wellness, and social impacts applicable to product(s). Valid certificate to be submitted along with the technical bid.6. Shutters & Side Legs: - Front, and back shutters shall be of 18 mm Laminated MDF Board with premium finish.Side leg shall be of 25mm of the same finish.The central portion of the side leg shall feature illuminated strip on the periphery. To ensure healthier air quality for the operators. The proposed console shall be Greenguard Gold certified. Valid certificate to be submitted along with the technical bid.7.The proposed console shall be RoHS Certified/tested from UL/Intertek and the valid certificate/ test report shall be submitted along with the technical bid.

14 Monitors Console for Communication Room (Fixed Height)New Modular Control Desk for provision of 14 monitors & 07 Operators made in " XLAT" system.1. Table top: - The material of the working surface shall be minimum 12/18 thick Compact Laminate. The proposed Control Desk’s life cycle should be assessed (from approved LCA consultant) for environmental impacts associated with all the stages of a product's life for cradle to grave analysis. Valid report/document from UL/Intertek to be submitted along with the technical bid.2. Structure: - 2.1. Made of heavy-duty extruded vertical and horizontal aluminium profiles. The extrusions shall be duly powder coated with 40+ microns over all surfaces. All sheet metal parts shall be finished with a durable, black, electrostatic powder coating. OEM shall have a valid trademark registration certificate issued by the Government of India for the Control Desk proposed in this tender. Valid Trademark registration certificate to be submitted along with the technical bid.2.2. To allow future extension and expansion, a weld-free system shall be proposed. Interconnecting joints shall not be visible. The structure shall be rigid enough to withstand BIFMA X5.5 tests.The structure shall allow easy assembly of hinged shutters, slat wall, gland plate, and monitor arms in extremely rigid manner. Valid certificate of BIFMA X5.5 from authorized agencies to be submitted along with technical Bid.2.3. The EPD (Environmental product declaration) of Control Desk shall be verified in accordance with ISO 14025 (from UL/Intertek) for Impacts on Environment by Control Desk. Valid report/document from UL/Intertek to be submitted along with the technical bid.2.4. Consoles shall be tested and qualified to sustain seismic vibrations as per design spectrum IS 1893 for zone 4 vibrations with monitor mounted on monitor arms of the control room console. Seismic safety of user & equipment is a prime concern area. This test shall be carried out by authorised government agency. Test report with images of control room console seismic test shall be submitted along with technical bid.3. Slat Wall: - Slat wall shall be made of approximately 2mm thick extruded aluminium (aluminium alloy). 4. Monitor Arm: - The Console shall feature ergonomic display mounting arms. It shall enable quick & easy replacement of VESA mounts & arm extensions. UL audit certified design feature of monitor arm assembly shall have auto lock, push & remove feature for quick release of VESA mounts and modular arm extensions for ease in maintenance and fixing of monitor by one technician within 30 seconds without using any tools. Valid UL audit certificates to be submitted along with the technical bid.5. The proposed control desk shall be ANSI/BIFMA e3-2019 certified/tested at least for level 3 from UL/Intertek as per Furniture Sustainability Standard to identify the sustainability level of the furniture with respect to the environmental, health & wellness, and social impacts applicable to product(s). Valid certificate to be submitted along with the technical bid.6. Shutters & Side Legs: - Front, and back shutters shall be of 18 mm Laminated MDF Board with premium finish.Side leg shall be of 25mm of the same finish.The central portion of the side leg shall feature illuminated strip on the periphery. To ensure healthier air quality for the operators. The proposed console shall be Greenguard Gold certified. Valid certificate to be submitted along with the technical bid.7.The proposed console shall be RoHS Certified/tested from UL/Intertek and the valid certificate/ test report shall be submitted along with the technical bid.

DISPENSING MECHANISM -PESO Approved Dispensing UnitPositive displacement type suitable for achieving maximum accuracy at operating range of 35 PM to 75 LPM at nozzleAccuracy: + 0.1%PESO & W&M approved tamper proof PulsarElectronic Display with totalizer and a reset optionElectronic calibrationSolenoid Valve: PESO approved make. Dual stage type control mechanism for accurate preset deliveryStriner suitable for diesel application Pump: suction type Fuel grade hose size 1°X3.0 metresSize- 1" Nozzle with 1° spoutAuto cut-off to prevent over fuellingCenification- Ex suitable Zone 1. A TEX/PESO approvedFlow rate · Max 35· 75 LPM Receipt printer for transaction statementFUEL LEVEL SENSORSAuto Tank Gauging sensors for real time inventory morntonng An intrinsic salety barrier rs used to provide protection to sensorsManufactured ln rigid stainless steel. for a durable, long· and quality solution. Utilizing magneto strictive lasting technology for high accuracyVery high accuracy sensors with+/· 0.2 % accuracyTANKShell Bottom and top 152062 HR E250 grade Mild Steel tank of minimum 3 mm thickness comflrming to 15 2062 with s1ngle/mult1ple compartment with 5% vapor spaceRobust construct to prevent unsecured access to the man hole. Locking system as per Repos standardsEach Compartment is fitted with an individual manhole covefixed type with CCOEapproved safety fittingsFire screen between tank and dispensing CabinetWell ventilated louvers (window blind or shutter with horizontal slats that are angled to admit light and air). front opening with locking mechanismloT CONTROLLERRepos loT Controller enables complete DATUM automation system Industry grade arm cortex MO architecture based controllerConnected with the DATUM app using wireless architecture for secured data transmissionSupports OTA (Over the air) firmware updates for speedy resolvement of issues occured on siteOperates on isolated power supplyFLAME PROOF LIGHTCCOE approved flame proof lights installed within the dispensing cabinet for better illuminationQUALITY KITHyrdrometer. Thermometer. Measuring BeakerQUANTITY KITDipstick, 5 Litre JarSAFETY KITOne 9KG C02 fire extinguisher. One set of Fire Bucket

Supplying, drilling /cleaning hole and fixing of HILTI Torque Controlled Expansion Anchor HST2 V3, of sizes ranging from M8 to M16 for fixing of HVAC ducts. The Anchor should possess ETA Certificate for use in both Cracked Concrete and non-cracked concrete, approved as per Seismic C1 and C2 Category and have Fire Resistance values for up to 120 mins tested in accordance with EAD 330232-01-0601. The anchor should be pre-assembled with a galvanized bolt as per EN ISO 4042: 1999, a nut of Strength Class 8 (EN ISO 20898-2:2012) and a galvanized washer (EN ISO 4042:1999). It should also possess FM Approval for use in Pipe Hangers. Design of Anchor should be done as per EC2 Part-4 using PROFIS Engineering Software as per actual load data and site conditions as provided by structural consultant and the report to be submitted to the project manager and design engineer for approval. Anchor shall be driven with the help of HS-SC setting tool ,fixed at right embedment depth as per design report and activated using Hilti SIW 6AT-A22 Impact Wrench with adaptive torque Module to ensure adequate torque as per the given diameter mentioned in the ETA.The same must be documented in the form of software generated report and shall be submitted to the peoject manager at the time of inspection. Scanning before drilling to be done with Hilti PS Scanning tool to avoid rebar hits. Safety stud anchor HST2 V3 M10x110

Supplying, drilling /cleaning hole and fixing of HILTI Torque Controlled Expansion Anchor HST2 V3, of sizes ranging from M8 to M16 for fixing of Cable tray supports. The Anchor should possess ETA Certificate for use in both Cracked Concrete and non-cracked concrete, approved as per Seismic C1 and C2 Category and have Fire Resistance values for up to 120 mins tested in accordance with EAD 330232-01-0601. The anchor should be pre-assembled with a galvanized bolt as per EN ISO 4042: 1999, a nut of Strength Class 8 (EN ISO 20898-2:2012) and a galvanized washer (EN ISO 4042:1999). It should also possess FM Approval for use in Pipe Hangers. Design of Anchor should be done as per EC2 Part-4 using PROFIS Engineering Software as per actual load data and site conditions as provided by structural consultant and the report to be submitted to the project manager and design engineer for approval. Anchor shall be driven with the help of HS-SC setting tool ,fixed at right embedment depth as per design report and activated using Hilti SIW 6AT-A22 Impact Wrench with adaptive torque Module to ensure adequate torque as per the given diameter mentioned in the ETA.The same must be documented in the form of software generated report and shall be submitted to the peoject manager at the time of inspection. Scanning before drilling to be done with Hilti PS Scanning tool to avoid rebar hits. Safety stud anchor HST2 V3 M10x110

Supplying, drilling /cleaning hole and fixing of HILTI Torque Controlled Expansion Anchor HST2 V3, of sizes ranging from M8 to M16 for fixing of Fire fighting pipes. The Anchor should possess ETA Certificate for use in both Cracked Concrete and non-cracked concrete, approved as per Seismic C1 and C2 Category and have Fire Resistance values for up to 120 mins tested in accordance with EAD 330232-01-0601. The anchor should be pre-assembled with a galvanized bolt as per EN ISO 4042: 1999, a nut of Strength Class 8 (EN ISO 20898-2:2012) and a galvanized washer (EN ISO 4042:1999). It should also possess FM Approval for use in Pipe Hangers. Design of Anchor should be done as per EC2 Part-4 using PROFIS Engineering Software as per actual load data and site conditions as provided by structural consultant and the report to be submitted to the project manager and design engineer for approval. Anchor shall be driven with the help of HS-SC setting tool ,fixed at right embedment depth as per design report and activated using Hilti SIW 6AT-A22 Impact Wrench with adaptive torque Module to ensure adequate torque as per the given diameter mentioned in the ETA.The same must be documented in the form of software generated report and shall be submitted to the peoject manager at the time of inspection. Scanning before drilling to be done with Hilti PS Scanning tool to avoid rebar hits.Safety stud anchor HST2 V3 M10x110

Providing and supplying HILTI Torque Controlled Expansion Anchor HST2 V3 of HILTI make for fixing of Plumbing pipe supports. The Anchor should possess ETA Certificate for use in both Cracked Concrete and non-cracked concrete, approved as per Seismic C1 and C2 Category and have Fire Resistance values for up to 120 mins tested in accordance with EAD 330232-01-0601. The anchor should be pre-assembled with a galvanized bolt as per EN ISO 4042: 1999, a nut of Strength Class 8 (EN ISO 20898-2:2012) and a galvanized washer (EN ISO 4042:1999). It should also possess FM Approval for use in Pipe Hangers. Design of Anchor should be done as per EC2 Part-4 using PROFIS Engineering Software as per actual load data and site conditions as provided by structural consultant and the report to be submitted to the project manager and design engineer for approval. Anchor shall be driven with the help of HS-SC setting tool ,fixed at right embedment depth as per design report and activated using Hilti SIW 6AT-A22 Impact Wrench with adaptive torque Module to ensure adequate torque as per the given diameter mentioned in the ETA.The same must be documented in the form of software generated report and shall be submitted to the peoject manager at the time of inspection. Scanning before drilling to be done with Hilti PS Scanning tool to avoid rebar hits.Screw anchor HST2 V3 M10x90

Supply of modular type Variable Refrigerant Flow / Volume SYSTEM only cool comprising of 100% DC inverter based scroll compressor only ,connectable to multiple indoor units as perspecification. Outdoor units shall be factory assembled weather proof. Casing constructed from heavy gauge mild steel(sheet metal material is hotzinc plate & sheet metal thickness is 1 mm),must have 100% DC Inverter Scroll compressor in each module & with top Air discharge through. Theoutdoor unit shall be be complete with safety devices .The outdoor unit should be fitted with low noise fan with multiple speed DC motor and large airflow. The unit should also be capable to deliver at least 70pa external static pressure to avoid short cycling of hot exhaust air, Air-cooled condenseralong with in built Micro Processor Panel. Units should be capable to handle incoming voltage fluctuation during operation it should have a voltage operating range from 320V - 460 V 3 phase 50Hz, balanced volt. Considering the long length piping the unit should have a good oil managementsystem to ensure reliability.Outdoor Unit only Cool. (Approved Make Daikin/Mitsubishi/Blue Star/Voltas)60Hp

Supply of modular type Variable Refrigerant Flow / Volume SYSTEM only cool comprising of 100% DC inverter based scroll compressor only ,connectable to multiple indoor units as perspecification. Outdoor units shall be factory assembled weather proof. Casing constructed from heavy gauge mild steel(sheet metal material is hotzinc plate & sheet metal thickness is 1 mm),must have 100% DC Inverter Scroll compressor in each module & with top Air discharge through. Theoutdoor unit shall be be complete with safety devices .The outdoor unit should be fitted with low noise fan with multiple speed DC motor and large airflow. The unit should also be capable to deliver at least 70pa external static pressure to avoid short cycling of hot exhaust air, Air-cooled condenseralong with in built Micro Processor Panel. Units should be capable to handle incoming voltage fluctuation during operation it should have a voltage operating range from 320V - 460 V 3 phase 50Hz, balanced volt. Considering the long length piping the unit should have a good oil managementsystem to ensure reliability.Outdoor Unit only Cool. (Approved Make Daikin/Mitsubishi/Blue Star/Voltas)14Hp

Supply of Cassete type VRF indoor units with compact cooling coil, electronic expansion valve and multispeed fan motor. The blower shall be statically & dynamicaly balanced and designed forsilent operation, the filters shall be washable synthetic media type arranged for convenient cleaning and replacement. The unit shall also consist ofdrain pan and drain pump and Cordless Remote Controller. Large Casseette UnitCapacity-4TR

Supply of Cassete type VRF indoor units with compact cooling coil, electronic expansion valve and multispeed fan motor. The blower shall be statically & dynamicaly balanced and designed forsilent operation, the filters shall be washable synthetic media type arranged for convenient cleaning and replacement. The unit shall also consist ofdrain pan and drain pump and Cordless Remote Controller. Large Casseette UnitCapacity-3.2TR

Supply of Cassete type VRF indoor units with compact cooling coil, electronic expansion valve and multispeed fan motor. The blower shall be statically & dynamicaly balanced and designed forsilent operation, the filters shall be washable synthetic media type arranged for convenient cleaning and replacement. The unit shall also consist ofdrain pan and drain pump and Cordless Remote Controller. Large Casseette UnitCapacity-2.56TR

Supply of Cassete type VRF indoor units with compact cooling coil, electronic expansion valve and multispeed fan motor. The blower shall be statically & dynamicaly balanced and designed forsilent operation, the filters shall be washable synthetic media type arranged for convenient cleaning and replacement. The unit shall also consist ofdrain pan and drain pump and Cordless Remote Controller. Large Casseette UnitCapacity-2.0Tr

Supply of Cassete type VRF indoor units with compact cooling coil, electronic expansion valve and multispeed fan motor. The blower shall be statically & dynamicaly balanced and designed forsilent operation, the filters shall be washable synthetic media type arranged for convenient cleaning and replacement. The unit shall also consist ofdrain pan and drain pump and Cordless Remote Controller. Large Casseette UnitCapacity-2Tr

Supply of Cassete type VRF indoor units with compact cooling coil, electronic expansion valve and multispeed fan motor. The blower shall be statically & dynamicaly balanced and designed forsilent operation, the filters shall be washable synthetic media type arranged for convenient cleaning and replacement. The unit shall also consist ofdrain pan and drain pump and Cordless Remote Controller. Large Casseette UnitCapacity-1.5Tr

Supply of Cassete type VRF indoor units with compact cooling coil, electronic expansion valve and multispeed fan motor. The blower shall be statically & dynamicaly balanced and designed forsilent operation, the filters shall be washable synthetic media type arranged for convenient cleaning and replacement. The unit shall also consist ofdrain pan and drain pump and Cordless Remote Controller. Large Casseette UnitCapacity-1.3TR

Supply of Cassete type VRF indoor units with compact cooling coil, electronic expansion valve and multispeed fan motor. The blower shall be statically & dynamicaly balanced and designed forsilent operation, the filters shall be washable synthetic media type arranged for convenient cleaning and replacement. The unit shall also consist ofdrain pan and drain pump and Cordless Remote Controller. Large Casseette UnitCapacity-1Tr

Supply of Cassete type VRF indoor units with compact cooling coil, electronic expansion valve and multispeed fan motor. The blower shall be statically & dynamicaly balanced and designed forsilent operation, the filters shall be washable synthetic media type arranged for convenient cleaning and replacement. The unit shall also consist ofdrain pan and drain pump and Cordless Remote Controller. Large Casseette UnitCapacity-.8Tr

VRF Ducted UnitCapacity-4Tr

VRF TFA Unit For Fresh Air1024CFM

VRF TFA Unit For Fresh Air741CFM

Cordless Remote

Corded Remote

Supply Of Cu Refnet Joints for indoor and Outdoor.For indoor

Supply Of Cu Refnet Joints for indoor and Outdoor.For Outdoor

Supply of Ceiling Suspended Ducted UVGI ducted Unit with scroll Compressor Cu Condenser coil Microprocessor based Controller Compitable of R410A Gas.Capacity-8.5TR

Supply Of 3Star Hi-Wall Split Machines with Cu Condenser Coil,Rottary Compressor/Scroll Compressor,Microprocessor based Controller with Cordless RemoteCapacity-2.5Tr

Supply Of 3Star Hi-Wall Split Machines with Cu Condenser Coil,Rottary Compressor/Scroll Compressor,Microprocessor based Controller with Cordless RemoteCapacity-2Tr

VRF Out door shifting at location , Installation with Rubber pad ,Testing -Flushing with N2 & Commissioning . Out Door Unit60Hp

VRF Out door shifting at location , Installation with Rubber pad ,Testing -Flushing with N2 & Commissioning . Out Door Unit14Hp

Indoor Unit Installation,Testing & CommissioingVRF Cassette Unit

Indoor Unit Installation,Testing & CommissioingVRF Ducted Unit

Indoor Unit Installation,Testing & CommissioingVRF TFA Unit

Installation testing & Commissioing Of UVGI Ducted UnitCapacity-8.5TR

Installation,Testing and Commissioing of Cu Refnet Joints /Y JointsFor indoor

Installation,Testing and Commissioing of Cu Refnet Joints /Y JointsFor Outdoor

Installation,Testing and Commissioing of Split UnitCapacity-2.5Tr

Installation,Testing and Commissioing of Split UnitCapacity-2Tr

Supplying & Installation of interconnecting following sizes of one end expanded refrigerant copper pipe work of following outer diameter, insulated with 19/13 mm thick closed cell electrometric nitrile rubber tubular insulation between each set of indoor & outdoor units, all piping inside the room shall be properly fixed/supported with suitable size of clamp/ M.S. hanger.6.4mm Dia9.5mm Dia12.7mm Dia15.9mm Dia19.1 mm dia22.2mm Dia28.6mm Dia34.1mm dia41.3mm dia

Providing & fixing rigidC- PVC piping complete with fittings, supports as per specifications and pre insulated with 6mm thick closed cell elastomeric nitrile rubber tubular insulation. "25mm dia

Providing & fixing rigidC- PVC piping complete with fittings, supports as per specifications and pre insulated with 6mm thick closed cell elastomeric nitrile rubber tubular insulation. "32mm dia

Providing & fixing rigidC- PVC piping complete with fittings, supports as per specifications and pre insulated with 6mm thick closed cell elastomeric nitrile rubber tubular insulation. "40mm Dia

Supply, Installation, Testing & commissioning of sealded and fully proof copper flexible cable for indoor communication with all respect with PVC Conduit2 C X.75 SQMM

GI Duct24Gauge

GI Duct22Gauge

Duct thermal insulation with 13mm thick O class closed cell nitrille rubber

Duct accoustic insulation with 25mm thick O class Open Cell Nitrile Rubber

GI Duct DamperAl Powder Coated Grilles/Diffusers with VCD

GI Duct DamperAl Powder Coated Grilles /Diffusers with Out VCD

AL Powder Coated Cable Try for Copper Pipe Support200 x 55

AL Powder Coated Cable Try for Copper Pipe Support300 x 55

Fresh Air Connection with cassatte Unit and Duct with Damper and PVC Pipe.

SITC of fresh air louvers with bird screen and VCD

Gas Charging-R410A

Supply, Installation, Testing and Commissioning of ongrid Solar Photovoltaic Power Plant conforming to MNRE specifications as amended, consisting of Mono/Poly Crystalline silicon solar cells, net metering facility, necessary protections, earthing, mounted on Aluminium/GI structure of suitable strength with following components complete as required:- a) Solar Photovoltaic Module of capacity 330 Wp or above, manufactured in India, conforming to IS 14286/IEC 61215, IS/IEC 61730-Part-1, IS/IEC 61730-Part-2. Solar Photovoltaic Module conversion efficiency shall not be less than 16.5%. PV modules used in solar power plants/ systems must be warranted for their output peak watt capacity, which should not be less than 90% at the end of 10 years and 80% at the end of 25 years. b) Power Conditioning Unit (PCU) of 350-800 V DC Input voltage range and 400 V AC, three phase, 4 wire, 50Hz +/- 2.5 Hz, output voltage suitable to generate AC Power with efficiency not less than 97%, total harmonic distortion less than 3% and suitable for ambient temperature from 0 to 50 degree C. The PCU shall adjust the voltage and frequency level to suit the Grid Voltage Frequency.c) Data Monitoring System complete with accessories. d) Fixing of Array junction box & Main junction box with IP 65 protection and termination arrangement for incoming and outgoing cable along with glands, lugs and other accessories etc. as required. e) Lightning and surge voltage protection. f) Connections & Interconnections by supplying & fixing required size XLPE insulated copper conductor 1.1 kV grade armoured power and control cables between solar modules, main power cable to grid supply PCU unit along with supplying & fixing of necessary channel/conduit lugs and other accessories etc. as required.

Operation and maintenance for 1st year

Operation and maintenance for 2nd year year

Operation and maintenance for 3rd year

ESMP (Exact Amount to be quoted as per Bid Data Sheet Clause No. 14.2)