PROVN OF XBIS BAGGAGE ROOM AT SUB GUARD ROOM WITH ASSOCIATED WORKS SERVICES, COLD WATER GREASE TRAP IN MESSES, EXHAUST FANS IN CERTAIN SMQ AND SPECIAL REPAIR TO BUILDING OF STN SECURITY SECTION AND SUB GUARD ROOM AT AF STN UTARLAI

Amount

Excavation in trenches n exc 1.50 m wide and n exc 1.5 m in depth for foundation etc n exc 10sqm on plan in hard dense soil and getting out complete all as specified.

Excavation in trenches n exc 1.50 m wide and n exc 1.5 m in depth for foundation etc n exc 10sqm on plan in soft rock/disintegrated and getting out complete all as specified.

M&L PCC 1:4:8 type D-2 (using 40 mm graded stone aggregate) as in foundation, filling and mass concrete etc. complete all as specified.

Returning, filling in, including spreading, levelling, watering and well remming in layers n exc 25 cm, in soft soil complete all as specified.

Removing excavated soil, exc 50 m but n exc 250 m and deposited where directed at a level n exc 1.50 m above the starting point complete all as specified.

M&L for morrum/red bajri filling in floors or pavings,laid in layers n exc 15 cm thick each , spread,levelled and rammed including watering. complete all as specified.

M&L for 100 mm thick PCC (1:4:8) type D-2 using (40 mm graded stone aggregate) as in sub base. complete all as specified.

M&L for 50 mm thick PCC (1:2:4) type B-1 using (20 mm graded stone aggregate) as in floor finishing cement concrete surface even and fair with out using extra cement. complete all as specified.

M&L RCC M-25 (using 20 mm graded stone aggregate) as in footing, foundation and plinth beams etc. complete all as specified.

M&L RCC M-25 (using 20 mm graded stone aggregate) as in columns, pillars, piers, posts and struts. complete all as specified.

M&L RCC M-25 (using 20 mm graded stone aggregate) as in beams, cantilevers, bressumers, lintels, over 1.50 m span etc. complete all as specified.

M&L RCC M-25 (using 20 mm graded stone aggregate) as in slabs supported on walls, beams and columns in floors and roof etc and the like complete all as specified.

Formwork to sides of concrete foundations, footings, bases of columns and raft beams, side and soffits of foundation and plinth beams of rough finished surfaces of concrete complete all as specified.

Formwork to sides of pillars, posts, struts, piers,columns, and stanchions Rough finished surfaces of concrete Square, rectangular or polygonal complete all as specified.

Formwork to sides & soffits of floor or roof beams, beam haunchings, girders, bressum-mers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors & beams, etc. Rough finished surfaces of concrete flat complete all as specified.

Form work to soffits of suspended slabs, such as roof slab, floor slabs, landing and similar work, n.exc 200 mm thick (horizontal or sloping). complete all as specified.

M&L TMT bars 10mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire(annealed) not less than 0.9 mm diameter. complete all as specified.

M&L TMT bars 6 to 8 mm dia cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire(annealed) not less than 0.9 mm diameter. complete all as specified.

Ditto all as per item ser No 17 above but 5 to 10 mm diameter in stirrups, spacers and binders complete all as specified.

M&L for precast cement concrete block masonry with solid blocks of PCC 1:3:6 type C1 using 20 mm graded stone aggregate, exc. 10 cm in width and setting in CM 1:6 complete all as specified.

M&L for rendering 15 mm thick, in CM (1:6) on fair faces of brick or concrete surfaces of walls, finished even and smooth without using extra cement complete all as specified.

M&L for rendering 10 mm thick, in CM (1:3) on concrete surfaces in ceiling, fin facia chajja/concrete surfaces finished even and smooth without using extra cement complete all as specified.

M&L for rendering 15 mm thick in CM (1:4) in two layer i.e. first layer 10mm thick and second layer 5mm thick on surface other than fair finish of brickwork/concrete/PCC block masonry wall or on stone masonry wall using water proofing compound @ 3% by wt of cement mixed with in second/finish coat and finished even and smooth without using extra cement ( Note : WPC will be measured & paid seperately) complete all as specified.

Supply only integral water proofing compound ISI marked. complete all as specified.

M&L for Preparing newly plastered surfaces of walls and applying two coats of oil bond distumper over a coat of primer. complete all as specified.

M&L for Preparing newly plastered surfaces of ceiling and applying three coats of white wash complete all as specified.

M&L Preparing new plastered surfaces and applying two coats of cement base paint over a coat of primer on wall surface etc complete all as specified.

M&L PCC (1:4:8) type D2 (using 40mm graded stone aggregate) as in sub base, 75 mm thick , finished even and fair without using extra cement complete all as specified.

M&L PCC (1:3:6) type C-2 (using 40mm graded stone aggregate) as in plinth protection, 75mm thick, finished even and fair without using extra cement complete all as specified.

S & F fctory made solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, as per specification and drawing complete all as specified.

S & F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M S tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, as per specification and drawing complete all as specified.

S & F 100mm size type B-21 butt hings extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed complete all as specified and as directed by Engr-in-Charge.

S & F extruded aluminium alloy handles fabricated types, anodised each 150mm size complete all as specified.

S & F aluminium, anodised, barrel tower bolt of extruded section and fixed, 200mm long complete all as specified.

S & F extruded aluminium alloy, anodised, slidind door bolt 300mm in length with hasp, staple (bolt type) and fixing bolts and sliding bolts of extruded sections complete all as specified.

S & F factory made steel ventilator with top hung shutter including hinges, steel peg stay, complete all as specified.

M & L for Anodised aluminium door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, ruber neoprence packing, handles 2 Nos in each door, hinges, anodised aluminium snap beading screws etc, complete all as specified.

M & L for Anodised aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glasing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified.

S & F sheet glass 3.00 mm thick, ordinary quality and glazing with oil putty or wooden beads supplied with shutters in square n.exc. 0.5 sqm in each pane complete all as specified.

M & L preparing new steel surfaces of any description, over 10 cm in width or girth, and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified.

S & F vitreous china wash down white water closet pan (squatt pattern ) orrisa pattern complete size 580 x 440 mm with integral footrest (excl flushing cistern & flush pipe) incl lime concrete etc complete all as specified.

M & L cast iron Nahani trap/floor trap 75mm dia of outlet with grating including jointing to waste pipe, fixed in PCC (1:2:4) type B-1 (using 20 mm graded stone aggregate), complete all as specified.

S & F 10 liters PVC valveless, syphonic action type flushing cistern, white with inlet, ball valve, float and handle including brackets complete all as specified.

S & F Chromium Plated pillar tape, fancy type cast copper alloy, with capstan heads, screwed down high pressure, with or without lettered 'hot or cold' with long scerwed shanks and fly nuts screwed for iron pipe of 15 mm bore dia. complete all as specified.

S & F 15 mm bore Chromium Plated bib tap fancy type cast copper alloy with crutch or butterfly handle with screwed down, screwed for iron pipe. complete all as specified.

S&F 15mm bore Chromium Plated stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified.

S & F waste coupling brass Chromium Plated for glazed wash basin with long screwed shanks and fly nut 32 mm diameter complete all as specified.

S & F PVC waste pipe 32 mm dia for wash hand basin & Urinal Pot low density polyethyulene (LDPE) had pipe of pressure rating 6 kgf/Sqcm complete all as specified.

S & F Towel rail 600mm long of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats. (Minumum weight 190 gms) complete all as specified.

S & F PVC connection 15 mm dia and 450 mm long with both end socket fixed complete all as specified.

S & F grating 125 mm dia of PTMT with waste hole (Min Wt 40 gms). complete all as specified.

S & F 15mm bore GI Tubes medium grade in lengths with screwed and socket jointsl with all galvanised steel fittings such as bends, tees, reducers unions, cap plugs, nipples etc fixed complete to walls by means of and including clips, connecaled in walls, floors complete all as specified.

-dito- all as per item Ser No 52 above but 20 mm bore complete all as specified.

M & L cast iron (spun pipe) soil, waste and vent pipes, in any length with or without ears with cement joints, laid in trenches or in floors 100 mm dia complete all as specified.

M & L cast iron (spun pipe)soil, waste and vent pipes, in any length with or without ears with cement joints, fixed to walls 100 mm dia. complete all as specified.

M & L cast iron (spun pipe)soil, waste and vent pipes, in any length with or without ears with cement joints, laid in trenches are in floors 75 mm dia. complete all as specified.

M & L cast iron vent cowl 100 mm bore complete all as specified.

M & L for cast iron Bends, 75 mm bore laid and jointed, complete all as specified.

M & L for 75 mm dia cast iron trap P or S laid and jointed, complete all as specified.

Supply and fixing for Vitreous China wash basin, white, flat back, size 600 x 480 excluding taps, waste pipe and porcelain stopper but including brackets, pinning in ends of brackets/erecting stand neccesary fixing complete all as specified.

M & L for rendering 10 mm thick in cement mortar 1:3 with WPC @ 3 % by weight of cement on roof surface finished even & fair complete all as specified. NOTE : Water Proofing Compound shall be measured and paid separetely.

M & L for applying roof treatment on top of roof with 3 mm minimum thickness APP modified membrane (weighing 3 Kgs/sqm) with non-woven polyster reinforcement/mat(centre core) with thermal insulation with white mineral finish on upper side of membrane laid by torch application method with overlap 100 on length and 100 mm on the width side as per manufacture's instructions over a coat of approved cold applied butuminous oil based primer (IS-3384) @ 250gm/sqm complete all as specified and directed by engineer-in-charge.

supply and Fixing for Vitreous China urinals, half stall type (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, ecuring urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement: fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe including cost of waste pipe, PVC connection etc complete all as specified.

M & L for Vitrified Ceramic tiles 10 mm thick light shade laid over and including 15 mm thick screed bed in CM 1:6 (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified.

M & L for Vitrified Ceramic tiles 10 mm thick dark shade laid over and including 15 mm thick screed bed in CM 1:6 (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified.

Ditto all as per item above but as in skirting/dado over 10mm thick cement plaster in CM 1:4 complete allas specified and directed.

M & L for coloured non- skid ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 15 mm thick screed bed in CM 1:6 complete all as specified.

M & L for 20 mm thick Granite (of any type) work (table rubbed and polished) for wall lining (veneering to wall) 12 mm thick in cement mortar 1:3) and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified.

M & L for GI frame work for seamless ceiling comprising of GI perimeter channel 0.55 mm thick with two unequal flanges of 20 to 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to ntre/ intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with GI cleat and steel expansion fastners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel at 457 mm centre to centre complete all as specified.

M & L for 12 mm thick non asbestos fibre cement building boards fixed or laid/ inserted to timber/GI/Aluminium framework with screws complete all as specified.

M & L for 12 mm thick Prelaminated particle board, exterior grade prelaminated one side with decorative choice lamination and other side balancing white lamination, fixed with screws to complete all as specified.

Suppling and fixing 4 mm thick sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 m in each pane complete all as specified.

Suppling and fixing 4 mm thick frosted /obscured sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 m in each pane complete all as specified.

S & F for mild steel mortice lock, vertical type size 100 mm 4 levers complete all as specified.

M & L for rotational moulded polyethlene 500 ltr capacity water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as spcified in SSR Part-I complete all as specified. Note:- PVC tank shall be ISI marked & having two layers.

S & F for 150 mm long aluminium anodised, barrel tower bolts extruded section and fixed complete all as specified.

S & F for 200 mm long aluminium anodised, barrel tower bolts ox extruded section and fixed complete all as specified.

S&F anodized aluminum brown/ white colour door made of anodized aluminum frame size 101x44x2mm thick and anodized aluminum shutters bottom rail of size 114x44x2mm, top rail 83x44x2mmm, middle rail 85x44x2mm with two numbers of disc / D type handle in each shutter, 200 size aluminum tower bolts 02 Nos brass lock 04 levers and key, floor door spring and hydraulically regulated door closer glazing with 5mm thick tinted glass in upper panel and with 12mm thick per laminated particle board in lower panel including rubber gasket, amuminum beading complete all as specified.

S&F three track aluminum powder coated sliding window with three sliding shutter, the size of outer frame three track 100 x37x1.50mm (using two track for glazed window shutter and one track for wire gauged ), the section shutter size 37x18x1.2mm a and glazing with 5 mm thick transparency glass of poly carbone including all-around suitable rubber gasket and stainless steel wire cloth 0.36 mm nominal dia of wire and avrge width of aperture 1.4mm and fixed on aliminum flat and inserted in the frmae of shutter with tracking arrangement eeach sliding window shall be provided with one bnumber handle including licking arrangement & 2 numbers sliding rollers of nylon with including all necessary fittings complete all as specified.

M&L for Anti termit treatment for Treating the bottom and sides of excavation at the rate of 5 litres of emulsion per square metre of surface area complete all as specified.

M&L for Anti termit treatment for Treating of backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface. (Area of the sub structure in contact with backfill to be measured). complete all as specified.

M&L for Anti termit treatment for Treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface complete all as specified.

M&L for Anti termit treatment for Treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area complete all as specified.

M&L for Anti termit treatment for Treating the soil with external perimeter of building at the rate of 2.25 litre of emultion per metre complete all as specified.

Demolition of concrete in groound floors and pavings n exc 15 cm thickness (below or above ground level) and removing of debris out of defence land complete all as specified.

Dismantling of Brickwork or stone/ boulder masonry, built in lime mortar or in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast. complete all as specified.

M & L for PCC 1:3:6 type C2, using 40mm graded for bed concrete to drain pipe packing under and hunching against the sides of 150 mm dia pipes after they are laid tested complete all as specified.

M & L for 150 mm bore, reinforced concrete drain pipes class NP2, laid and jointed complete with collars complete all as specified.

M & L for Cutting into existing manholes for connecting new sewage line 150mm dia, making good to pipe & rendering, cutting out existing benching for & forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished, & reforming benching as required complete all as specified.

S&F PTMT urinal spreader in any colour for fixing with 15mm dia pipe (min wt 60gm) complete all as specified.

Rough excavation n exc 1.5 m deep & getting out in hard/ dense soil complete all as specified.

-Ditto- all as per Item above above but depth exceeding 1.50m and n exc 3.0m complete all as specified.

M&L for PCC 1:2:4 type B-2 (40 mm graded stone aggregate) in foundation complete all as specified.

M&L for Pre-cast cement concrete 1:3:6 Type C-1 (20 mm graded stone aggregate) block mansonry with solid blocks, exc 10 cm in width and setting in motor, in CM 1:4 complete all as specified.

M&L for Rendering 15 mm thick on stone masonry surfaces or surface other than fair face of brick work in CM (1:6) finished even and smooth complete all as specified.

S&F stainless steel tank 304 grade 3mm thick of size 3x2x3 m (LxBxH) 02 Nos of intermediate partitions in tank and 02 Nos of covers on top complete all as specified and shown on drawing.

S&F framed work such as grills, gratings etc, with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed blastures; walk ways; railings; framework of water tanks & similar work conforming to Fe 290-0 Gde E-165 complete all as specified.

M & L for Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required; hooks (stay), heavy,, for large gates, hook & pintel hinges; large hasps & staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way & three way straps, plate washers & similar small articles conforming to Fe290-0 Gde E-165 complete all as specified.

S&F Mild steel, plain black sheet 1.25 mm thick in hearths; covering to door shutters; covering to door chowkats (frames); chullah hoods; waters tanks; water troughs; ducts; urinal troughs & funnels, etc cut to size, edges beaded if directed, holes punched; including round headed screws; clout nails or rivets & fixed to wood or steel members, etc., with plain 40 mm lap joints or welded/riveted seams including bending, turning up, mitred angles, stopped ends, outlets, etc. as required complete all as specified.

M&L PCC in surface channels and drains type B-2 (1:2:4) using 40mm graded stone aggregate complete all as specified.

M&L Precast cement concrete 1:2:4 Type B-1 (20 mm graded stone aggregate) in cover slap of manhole set in CM 1:4 complete all as specified.

M&L for two coats of synthetic enamel paint over primed surface on newly surface of concrete of any description over 10 cm girth or width not otherwise described including preparation and as directed by Engineer-in-Chage.

Demolition of brickwork or stone/boulder masonry, built in CM or cement lime mortar including all quions, arches, pillars etc, but excluding ashlar facings, dressed stonework & precast concrete articles 3M high above ground level complete all as specified.

M&L for 15mm thick rendering over dubbing out average 20mm thick cement plaster (1:4) on irregular face of walls (when specifically ordered in writing) complete all as specified.

M&L for Random rubble walling, uncoursed, well bounded, bedded and solidly hearted built in CM (1:6) complete all as specified.

S&F Stainless steel wire cloth, 0.36mm nominal dia of wire & average width of aperture 1.40mm with stainless steel wire staples complete all as specified

S&F Coloured Glazed ceramic tiles in vertical surfaces 350x250mmx7mm / 450x350x7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match shade of tiles , laid over and including 10mm thick plaster in CM (1:6) finished even & fair complete all as specified.

M&L for Point wiring with 1.5 Sqmm PVC insulated and unsheathed multi stranded FRLSH flexible copper conductor cable in and incl rigid PVC conduit concealed in wall with pressed mild steel terminal boxes duly painted with a coat of red oxide primer fixed flushed to the wall with 3mm thick plastic laminated sheet cover of adequate size for one light/fan controlled by one switch incl 1.5 Sqmm FRLSH, PVC insulated and unsheathed multi stranded flexible copper conductor cable as earth wire to common earth dolly, including cutting chases in block masonry wall , replastering and making good to match the existing specifications complete all as specified and directed by Engr-in-charge. Note: a) Unit rate shall be include for cutting chases for conduits and sunken boxes and making good to wall, floors etc

All as per item above but for one 3 pin 5 Amp socket outlet on same board complete all as specified.

All as per item above but for one 3 pin 5 Amp socket outlet on independent board complete all as specified.

M&L for Point wiring with 2.5 Sqmm PVC insulated and unsheathed multi stranded FRLSH flexible copper conductor cable in and incl rigid PVC conduit concealed in wall with pressed mild steel terminal boxes duly painted with a coat of red oxide primer fixed flushed to the wall with 3mm thick plastic laminated sheet cover of adequate size for one 3 pin socket outlet 15 Amp on independent board incl 2.5 Sqmm FRLSH, PVC insulated and unsheathed multi stranded flexible copper conductor cable as earth wire to common earth dolly, including cutting chases in block masonry wall , replastering and making good to match the existing specifications complete all as specified and directed by Engr-in-charge. Note: a) Unit rate shall be include for cutting chases for conduits and sunken boxes and making good to wall, floors etc.

Supply & fix switch piano flush button single pole one way 5 amps 230 volts,complete all as specified and directed

Supply & fix socket outlet 5 amps 5 pin flush type, 230 volts, complete all as specified and directed

Supply & fix switch socket combination 2 in 1, 5 pin, 5 Amp flush type.

Supply & fix switch socket combination 2 in 1, 6 pin, 5 and 15 Amp flush type universal complete all as specified and directed.

Supply and fix Sheet metal enclosures for fixing MCBs SPN 8 way, 230 volts with 200 Amps rated bus bar with double door fixed flushed to the wall including making the hole in the wall and fixing the DB including cement work and plastering complete all as directed.

S&F MCB single pole and neutral, 240 volts 32 Amps complete all as specified and directed.

S&F MCB single pole, 240 volts 6 to 32 Amps complete all as specified and directed.

S&F MCB single pole, 240 volts 40 to 63 Amps complete all as specified and directed.

Supply & fix LED tube light fitting 1x20 W, 230 V, including LED (tube rod) ultra bright LED, 4 feet batten fitting fixtures, complete with all accessories internally pre-wired and including connecting up with three/two core twisted flexible copper conductor cable with suitable size all as specified and directed.

Supply and fix LED street light 20 W, with aluminium pressure die cast housing, glass in the front with complete with all accessories internally pre-wired and including connecting up with three core twisted flexible copper conductor cable with suitable size all as specified.

M&L bracket for street light fitting made out of 25 mm bore pipe light grade GI tube bent to shape required, fixed with and including MS flat iron clamps, bolts, nuts, washers duly painting the bracket with two coats of aluminium paint over a coat of zinc chrome primer including PVC copper cable 1.5 Sqmm 3 core connecting from ceiling rose to light fitting complete all as specified and directed.

Supply & fix ceiling rose surface bakelite 65x50mm three terminal isolated body on pvc round block complete all as specified and directed.

M & L for earthing complete with galvanised steel earthplate of size 60cmx60cmx6mm thick electrode and 4.0mm dia GI wire as earth lead, buried directly in ground (earth pit not less than 2.25m deep below ground level) with top edge of the plate not less than 1.5m below ground level, connected to 4.0mm earth wire by means of nuts, bolts, check nuts and washers of GI all as shown in electrical plate No.5 of SSR Part-I, connected to earth test terminal point all as specified or as indicated including testing on completion (Rates inclusive of neccessary excavation in any type of soil, earth work, PCC pit, CI cover, funnel with watering pipe, suitable size of light grade GI Protection pipe for earth strip in ground etc. all as required at site for complete earthing)

M&L for Supply, laying, connection and testing in trenches, under floors/roads or on walls cable XLPE insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables ISI marked with stranded aluminium conductor, 1100 volts grade of size 25 Sq mm 4 core complete all as specified and directed by Engr-in-Charge

Excavation in trenches, not exceeding 1.5 metre wide and n. exc 1.50m in depth, for laying of cable n exc 10sqm on plan and getting out in any type of soil complete all as specified.

Removing of excavated surplus soil n.exc 50M and deposited where directed at a level n.exc 1.5M above the starting point complete all as specified.

M&L for sand cushioning to all around the cable protection of natural Tibba sand all as directed (Note : Punning thickness will be measured and paid for payment purpose) complete all as specified.

Supply and Laying stone patti quarry faced Jodhpur type 4 to 5 Cm thick and 25 to 30 Cm wide putting on cable abutting to each other for cable protection complete all as specified and directed.

Supply and Laying light grade galvanised steel tube 50mm bore light grade for protection of cable complete all as specified and directed.

Supply and Fixing LT cable route indicator cast iron of suitable size mounted on 40x40x3 mm angle iron with height of 1.5 Mtr alongwith LT cable trench including planting in ground with PCC 1:2:4 type B-1 using 20mm graded stone aggregate complete all as specified and directed.

Supply install and testing in replacement of out door weather proof bus bar chamber of size 80cm x 30 cmx 25 cm made out of 18 SWG MS sheet having one side openable hinged door shutter with locking arrangement mounted on 40x40x6mm anle iron frame with legs welded and 04 Nos copper bus bar of 200 Amp rating provn of one MCCB TPN 63 Amp 16 KA for controlling Electric Supply complete erected on ground with necessary PCC 1:3:6 type C2 foundation complete bus bar chamber painted with two coats of approved enamel paints over one coat of primer including making cable connection with necessary gland, lugs/thimbles complete all as specified Note : Cost of dismantling/taking down old unserviceable bus bar chamber shall be included in the quoted rate of this item.

M&L earthing complete as per electrical plate No 5 of MES SSR Part-I with galavanised steel earth plate electrode 60cmx60cmx6mm thick, buried directly vertically in ground in a pit depth not less than 2.25 metres below ground level with top edge of earth plate at a depth not less than 1.5 M below normal ground level connected to and including galvanised iron or steel earth strip 25mmx4mm by means of bolts, nuts check nuts and washers of galvanised iron or steel. Earthing strip shall be protected by galvanised iron or steel pipe 50mm bore light grade and connected to continuous earth wire on pole/test point. Watering pipe shall be 20 mm bore GI medium grade. The earthing shall be of inclusive of excavation & earth work in any type of soil, charcol, salt, funnel PCC pit and RCC cover complete all as specified & tested complete all as specified. Note : 1. Following items deemed to be included in quoted rate (a) Earth electrode (b) Main earth lead from earth electrode to test point and further to equipment to be earthed upto 7.5 Mtr (c) M&L for connecting earth electrode and earth lead as specified (d) Adequate qty of charcol, dust and common salt as per direction. (e) All labour involved incl testing of earth network (f) Excavation and earth work or drilling hole for electrode (g) PCC pit and CI cover (h) Funnel with watering pipe, wiremesh and copper lugs etc as specified (j) GI protection pipe of size as specified for protection of earth lead from mechanical injury or tempring. 2. On testing after completion if the desired earth resistance is not obtained the earthing will be redone at no extra cost.

M&L for Dismantling concretepoles/struts, any size with accessories including earth work and deposit to E/M yard complete all as specified and directed by Engr-in-Charge.

M&L for stay assembly as shown on electrical plate No. 1 (SSR part -I) complete with accessories including earth work complete all as specified and directed by Engr-in-Charge.

Supply & fix exhaust fan metal body, AC single phase 230/240 V of size 300 mm sweep, 900 RPM, power flow, powder coated metallic finish, specially designed metal blades including fixing of louvers 300mm dia by using suitable fastener grouted in the wall, including PVC copper cable 1.0 Sqmm 3 core connecting from celing rose to exhaust fan complete all as specified and directed. Note:- Exhaust fan shall be ISI marked.

M&L point wiring with PVC insulated (FRLSH) unsheathed copper stranded conductor single core cable of 1.5 Sqmm size drawn through PVC casing caping fixed on walls/ceilings with 1.6 mm thick fabricated pressed mild steel terminal box duly painted with a coat of red oxide primer fixed flushed to the wall with 3mm thick plastic laminated sheet cover for fixing switch complete with 1.5 Sqmm PVC insulated (FRLSH) copper conductor single core cable as earth continuity conductor connected to common earth dolly for one fan point controlled by one switch all as specified and directed by Engr-in-Charge.

Ditto as item above but for one 5 amps socket point controlled by switch on the same board with other switches.

Ditto as item above but for one 3 pin 5 Amp socket outlet on independent board.

Demolition of pre-cast PCC block walling / brick work or stone / boulder masonry including all quoins, arches, pillars, etc. built in cement mortar or cement lime mortar complete all as specified and directed

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing rubbish off the premises complete all as specified.

M&L for 40mm thick PCC 1:2:4 type B1,using 20mm graded stone aggregate as in floor finished concrete surface even & rough complete all as specified and directed.

Taking down cement plaster, any description on brick, concrete or stone walls or ceiling including raking out joints, hacking for key scrubbing down with water etc and removal of rubbish off all as specified and directed by engineer-in-charge

M & L for Dubbing out average 10mm thick CM 1:4 on irregular face of old walls/ ceiling,fin facia chajja, complete all as specified and directed

S & F GI chicken wire mesh of 0.71 mm dia wire & 12mm mesh size fixed with nails & screws around RCC chajjas/facias/ columns ,beam ,concrete wall / ceiling etc complete all as specified and directed

M&L for preparation on new plaster surface of ceiling & applying two coats of white wash complete all as specified and directed

M&L for complete removal of existing treament on old surfaces of walls and applying two coats of oil bound distemper over one coat of primer over and including 3mm thick (average) layer of wall care putty including rubbing down with sand paper to have smooth surfaces complete all as specified.

M&L for complete removal of existing treament on old surfaces of ceiling and applying two coats of oil bound distemper over one coat of primer over and including 3mm thick (average) layer of wall care putty including rubbing down with sand paper to have smooth surfaces complete all as specified.

M & L for PCC1:2:4 type B-1 (using 20 mm graded stone aggregate) as in coping or similar work etc including necessary form work complete all as specified and directed.

M&L for 20mm thick granite (of any type) work (table rubbed and polished ) in steps, jambs, pillars, window cills, cooking plateforms and like in cement mortor (1:4) including 15mm thick screed bed in CM 1:6, including pointing in white cement 1:2 using marble dust with admixture of pigment to match with shade of granite including moulding work on exposed edges of granite stones complete all as specified.

Demolition of reinforced cement concrete of any description and in any position (reinforcement cut as required to faciliate demolition) , complete all as specified and directed.

Formwork to edges of concrete flats, breaks in floors, openings in concrete walls, floors and roofs and sides of RCC/PCC bands in walls, horizontal or sloping, and similar work all exceeding 20cm wide,( flat rough finished surfaces of concrete.) . complete all as specified and directed.

M&L for RCC1:2:4 (Nominal mix) type B-1 using 20mm graded stone aggregate as in Beams, cantilevers, bressummers, lintels over 1.5m span, complete all as specified and directed.

S& F rolled section as in main and cross beams hip and jack rafters purlins where connected to common rafters and running rails and guides for sliding rails and guides for sliding doors fixed with angle cleats or other connecting plates and similar work con-forming to Fe.- 290. Gde-E, Complete all as specified and driected.

Taking down chowkhats or frames area not exc. 1.50 Sqm each with shutters (without taking off shutters from the frames) complete all as specified and directed.

Taking down chowkhats or frame exc 1.50 Sqm but n exc 4 Sqm each with shutters (Without taking off shutters from the frames) complete all as specified.

S & F anodised aluminium frame for doors, windows, ventilators partitions with one or more rebates including joining cleat for fixing etc. complete all as specified and directed.

S & F mild steel butt hinges "medium weight" cold rolled mild steel 100mm long complete all as specified.

S & F Mild steel butt hinge, 75 mm long, medium weight, cold rolled fixed with steel screws or welded to steel frame where required complete all as specified and directed .

S&F 125mm size, aluminium (cast type) anodized, handle and fixed with steel screws complete all as specified and directed

S&F 150mm size, aluminium D type purpose made fancy type handle for aluminum door only (cast type) anodized, and fixed with steel screws complete all as specified and directed.

S&F sheet glass 5 mm thick, ordinary quality and glazing with oil putty in square n.exc. 0.5 sqm in each pane complete all as specified.

M&L for 100mm thick Cement concrete (1:2:4), type B-2 using 40mm graded stone aggregate as in path/hard standing complete all as specified.

M&L for Kota stone slabs, 18-20mm thick, machine cut as in flooring of size not less than 550mm x 500mm each, set and jointed in cement slurry laid over & including screed bed of 20 mm thick in cement mortar (1:6) and pointed in cement mixed with pigment to match the shade of slab including rubbing, cutting and polishing (mirror type) complete all as specified.

M&L for machine cut kota stone slab flooring 18-20mm thick as in window cill skirting treads etc over cement screed base laid over 15mm thick rendering in CM 1:4 and jointed neat cement slurry with grey cement slurry with pigment to match the shade of the slab including rubbing cutting and polishing mirror finish type complete all as specified and directed

Dismantling of Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets

S&F Anodised aluminium snap grid of size 605 x 605mm frame work for false ceiling all as specified

S&F 12 mm thick Perforated particle board/ tiles for insulation and acoustic purposes, 60x60 cm in size, fixed with nails to timber framework or with staples or on snap grid as in ceiling , complete all as specified and as directed.

S&F in repairs door closer aluminium (die cast ) body hydraulically regulated designation No 3 universal type suitable for door shutter of 851 to 1000 mm in width of Aluminium body (die cast) weight between 61 to 80 Kg complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise complete all as specified and directed.

Dismantling, stone slabs and tiles of any description or thickness in floors, aprons etc laid dry or laid dry and pointed complete all as specified.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, socket. Light fitting, PVC conduit, steel conduit, PVC casing caping etc. complete including making good the disturbed surfaces of walls, ceilings complete all as specified and directed.

point wiring with 2.5 sqmm FRLS, PVC insulated and unsheathed multi stranded flexible copper conductor cable drawn in and including PVC casing caping of suitable size with pressed steel terminal boxes of adequate size fixed flushed to the wall with 3mm thickness plastic laminated sheet cover for one 3 pin socket outlet 15 Amp on independent board including continuous 2.5 sqmm FRLS,PVC insulated and unsheathed copper conductor cable (multistranded) as earth wire to common earth dolly, including cutting chases in brick wall, replastering and making good to match the existing specificationscomplete all as specified.

S&F fan regulator electronic flush type stepped (rotary type) with 5 steps speed control complete all as specified and directed.

S & F sheet metal powder coated versatile double door tripal pole and neutral (TPN) distribution system for MCB provisions, 415 volts, 50 Hz AC supply 4 way fitted with two cover with copper bus bar rated 200 amps neutral link, earth bar and din rail complete all as specified and directed.

S & F MCB TPN 63amps complete all as specified and directed.

S&F in sub main wiring with two run of single core (FRLS) PVC insulated and unsheathed cable with copper conductor (multistranded) having nominal area 2.5 Sqmm drawn into and including PVC casing caping of adequate size and making electric connections including one run (FRLS) PVC insulated single core copper conductor cable 2.5 Sqmm as a earth continuity conductor in and including PVC casing caping, including cutting chases in stone masonry wall wherever necessary for crossing the wall , replastering and making good to match the existing specifications complete all as specified and directed by Engineer-in-Charge. Note :- (i) Rates are deemed to be included cutting chases for making holes in stone masonry wall/floor for passing in or through conduit (ii) Two run of 2.5 sqmm single core (FRLS) PVC insulated copper conductor cable one run of 2.5 sqmm copper conductor cable (FRLS) as a earth lead and one run of casing caping of suitable size will be measured as a one unit.

-ditto- all as per item above but with 2 run of 4.0 Sqmm and one run of 4.0 Sqmm as earth continuity conductor complete all as specified & directed.

-ditto- all as per item above but with 2 run of 6.0 Sqmm and one run of 6.0 Sqmm as earth continuity conductor complete all as specified & directed.

M&L for Earthing complete with galvanized steel earth plate electrode 600x600x6mm thick buried directly in ground (Earth pit not less than 2.25 Metre deep below ground level) with top edge of the plate not less than 1.5 metre below normal ground level, connected to galvanized earth lead wire 4.0 mm dia by means of bolts, nuts, check nuts and washers of galvanized iron or steel all as shown in electrical plate No.5 of SI Part-I (2009) including filling of charcoal dust , common salt all around Earth plate upto 150mm, 20mm bore GI medium grade watering pipe, 15 mm bore light grade earth lead protection pipe upto main board, funnel with wiremesh, 40mm thick RCC 1:2:4 type B-1 using 20 mm graded crushed stone aggregate reinforced with suitable handle and angle iron frame and necessary excavation and earth work in any type of soil etc. complete all as specified and as directed including testing on completion. (Note: The rate quoted include cost of min 7.5 metre earthing wire)

M.D. CONSTRUCTION CO.

M/S M.D. CONSTRUCTION .CO