EUDCA-40/2025-26

Amount

Safe carriage of following materials from Store centre or any other place to the respective site of work through the Kachha/Pacca road including loading, unloading at the respective ends and erection of same including the work of dragging as per site requirement, jumphering of Transformer with 11 KV line through LT ABC cable, Weasal conductor etc. Cost of labour, T&P carrier etc. required for proper completion of work as per RESPO Norms is included in the work.

11Mtr. STP Pole (for Double pole Structure)

3x95 Sqmm. AB CABLE

ACSR Weasel Conductor

11 KV TPMO with Polymer Insulator

11 KV PIN INSULATOR with Pin

11 KV 45 KN DISC Insulator with Fitting

11 KV DO Fuse Set

Three Phase Distribution Box SMC

Stay set (16X1800 mm)

Earthing Complete

LT 3.5x70 XLPE Cable

LT 3.5x150 XLPE Cable

LT 3.5x400 XLPE Cable

1x400 Sqmm. LT XLPE Cable

1x120 Sqmm. LT XLPE Cable

11/0.4 KV 250 KVA Transformer

11/0.4 KV 100 KVA Transformer

11/0.4 KV 63 KVA Transformer

Supply, fixing and erection of following materials as per site requirement as per RESPO Norms:-

Tee off Chennal size 125x65x1300 mm. with Clamp, Nut, Bolt & Washers

Top Channel size 125x65x2240 mm. with Clamp, Nut, Bolt & Washers

Dropper Channel size 100x50x2028 mm. with Clamp, Nut, Bolt & Washers

Base Angle size 75x75x6x2028 mm. with Clamp, Nut, Bolt & Washers

Suspension clamp with i_hook

Dead end clamp with eye_hook

Pearcing Connector

DP Holding Clamp with Nut, Bolt & Washers

Danger Board with Clamp, Nut & Bolt

Barbed wire G.I.

Alumunium Lug off size

Copper L-Piece 50x225x10mm (LS)

Copper L-Piece 62x225x12mm (LS)

LT Fuse Set Protection Unit For UP To 100kva DT With SMC Box

LT INCOMING PANEL WITH METERING EQIPMENT

Henlay Type Telless Unit Protecetion cubical panel 500A, 650V

Concreting of Support

Neutral & Body earthing at 25 KVA/ 63 KVA/ 100 KVA /250 KVA Distribution Transformer by drilling/boring a hole of size 200 mm dia and 3000mm long in depth and then inserting the Gel earthing electrodes of size 50mm dia and 3000 mm long inside the pit then mix the back fill compound nicely with the soil and re-filling the empty space around the earthing electrode including making of chamber at the top of the earthing as per direction of supervising engineer. It includes the cost of all material labour, T&P, carrier etc. required for proper completion of work. The aforesaid work shall be carried out as per RESSPO norms. Max neutral to earth voltage should be less than 3 volts and earth resistance should be less than 1 ohm.

Construction of plinth at various 11/0.4 KV Sub-station suitable for distribution transformer having size 2x2x1.5 Mtr. Work will include digging of foundation 2’ deep & brick work with Ist class bricks having cement and sand mortar of ratio 1:6 on all the walls, each of 9” thickness. The area inside the wall shall be duly filled by mud up to the height of appropriate level from ground level and shall be duly watered & rammed. Above the filling C.C. of ration 1:6:12 (Cement sand and brick ballast) giving 4” layer shall be provided. Above C.C. layer RCC layer having 4” thickness and with ratio 1:2:4 of cement sand and stone ballast shall be provided Re-enforcement shall be provided by providing net of (8 Nos. + 8 Nos.) M.S. rods of size 10 mm dia and each of 2M length in the middle of the top of C.C. layer. The plinth shall be plastered with 12mm thick plaster in ratio 1:4 at all sides. This work will include cost of labour, T&P and all material required for construction of plinth which shall be provided by the contractor as per RESSPO Norms.

Providing and fixing of welded wire mesh fencing around transformer plinth with M.S. Angle of size 35X35X6 mm. length and 1.20 Meters height, such panels shall be supported on M.S. Angle from of size 40X40X6 mm. having 04 Nos. corner supports of height 1.65 Meters including extended legs for grouting which will be used as a door for entry of the personnel or removal/shifting of transformer with welded hinges, sliding belt etc. for locking the arrangement as per drawing and specifications the fencing will be painted one coat of red oxide primer and then two coats of bus green synthetic enamel paint. The rates should be inclusive of all materials required for proper completion of above work (length of each fencing approx. 11 Meters)

Demounting (removal) of following capacities old and used T/Fs from double pole/plinth to the ground & safe carriage of old and used transformer from site to ESC, Sarsol/workshop at Aligarh including loading unloading at both ends.

25KVA Distribution Transformer

63KVA Distribution Transformer

100KVA Distribution Transformer

D N S ENTERPRISES (BID ID -5537647)

KHAN ENTERPRISES (BID ID -5537838)